MLC 226 Series MediaLink® Controllers

Add to my manuals
5 Pages

advertisement

MLC 226 Series MediaLink® Controllers | Manualzz

Specifications

MLC 226 Series

IP Intercom

Connection type (IPI–MLC) ������������� RJ-45 jack for CAT 5/5e/6 cable

Audio

Frequency response ����������������� 20 Hz to 3�3 kHz, ±1 dB

Audio processing

Audio format ��������������������� PCM, µ-law companded

Sampling rate��������������������� 8 kHz

Sample size ������������������������ 16 bit, µ-law companded to 8 bit

Audio latency ��������������������� Software: 30 ms through 160 ms

Network: <150 ms, typical

Audio output

Number/signal type ������������������ 1 mono (for use with an optional IP Intercom)

Line level output ���������������������� -10 dBV (316 mVrms), unbalanced (via 3�5 mm captive screw connector, 2 pole)

Communication

Transport bandwidth for IPI control and audio, half duplex

80 kbps (0�08% of 100Base-T)

Ethernet protocol ��������������������� IP (control), TCP (control), UDP (audio)

Control host ports

Serial host port ������������������������������� 2 bidirectional RS-232: 1 rear panel female 9-pin D connector (shared with digital input), 1 front panel 2�5 mm mini stereo jack

Baud rate and protocol ������������������� 38400 baud, 8 data bits, 1 stop bit, no parity

Serial control pin configurations ����� 9-pin D connector: 2 = Tx, 3 = Rx, 5 = GND

Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND

Ethernet host port �������������������������� 1 female RJ-45

Ethernet data rate (for network communication)

10/100Base-T, half/full duplex with autodetect

Ethernet protocol ��������������������������� ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet

Ethernet default settings ���������������� Link speed and duplex level = autodetected

IP address = 192�168�254�254

Subnet mask = 255�255�0�0

Default gateway = 0�0�0�0

DHCP = off

Web server ������������������������������������� Up to 200 simultaneous sessions

7�25 MB nonvolatile user memory

Secondary control panel (SCP) �������� (1) 3�5 mm 5-pole direct insertion captive screw connector (shared with control module port)

Program control ����������������������������� Extron Global Configurator for Windows ®

Extron Simple Instruction Set (SIS ™ )

Microsoft ® Internet Explorer ®, Telnet

IR learning frequencies ������������������� 30 kHz to 62 kHz

IR learning distance ������������������������ 2" (5�1 cm) to 12" (30�5 cm) from the front panel

Control relay

Number/type ���������������������������������� 6 momentary or latching (configurable via software)

Connectors ������������������������������������ (3) 3�5 mm captive screw connectors, 3 pole

Connector configuration ���������������� Groups A, B, C; each with 1 common and 2 normally open relays (default)

Contact rating �������������������������������� 24 VDC, 1 A

Extron MLC 226 Series MediaLink ® Controllers • Specifications 1

Control serial ports

Display control port ������������������������ (1) 3�5 mm direct insertion captive screw connector, 3 pole, programmable for bidirectional RS-232 control (±5 V) or TTL level (0 to 5 V) infrared control up to

1 MHz

Switcher control port ���������������������� (1) 3�5 mm direct insertion captive screw connector, 3 pole, for bidirectional

RS-232 control (±5 V)

Baud rate and protocol (RS-232) ����� 115200 to 300 baud (9600 baud = default); 8 (default) or 7 data bits;

1 (default) or 2 stop bits; no parity (default), or even or odd parity

Control IR/serial ports

IR/serial control ports ���������������������� (3) 3�5 mm direct insertion captive screw connectors, 2 pole

Programmable: unidirectional RS-232 (±5 V) control, or TTL level (0 to 5 V) infrared control up to 1 MHz

Baud rate and protocol ������������������� 115200 to 300 baud (9600 baud = default) ; 8 (default) or 7 data bits;

1 (default) or 2 stop bits; no parity (default), or even or odd parity

Digital I/O control

Number/type ���������������������������������� 1 digital input/output (configurable), 1 digital input

Connector �������������������������������������� 1 rear panel female 9-pin D connector (shared with the serial host port)

(1) 3�5 mm direct insertion captive screw connector (shared with power sense port)

Pin configuration ���������������������������� 9-pin D connector: 1 = digital input, 5 = GND; power sense = digital in,

GND = GND

Digital inputs

Input voltage range ����������������� 0-12 VDC

Input impedance ���������������������� 28k ohms

Programmable pullup ��������������� 2k ohms to +5 VDC

Threshold low to high �������������� >2�8 VDC

Threshold high to low �������������� <2�0 VDC

Digital output ��������������������������������� 250 mA sink from 24 VDC, maximum

General

Power supply ���������������������������������� External

Input: 100-240 VAC, 50-60 Hz

Output: 12 VDC, 1 A

Power consumption

MLC 226 IP DV+ ���������������������� Includes MLC 226 IP and IRCM-DV+

Device �������������������������������� 5�4 watts, 12 VDC

Device and power supply ��� 6�5 watts, 100-240 VAC, 50-60 Hz

All other models

Device �������������������������������� 5�0 watts, 12 VDC

Device and power supply ��� 6�4 watts, 100-240 VAC, 50-60 Hz

NOTE: If the MLC powers accessories (control modules, SCPs), the MLC must be powered by its own external power supply, not by a switcher� If accessories are powered separately, the MLC may be powered by an MLS or PVS switcher�

Temperature/humidity �������������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling ������������������������������������������ Convection, no vents

Thermal dissipation

MLC 226 IP DV+ ���������������������� Includes MLC 226 IP and IRCM-DV+

Device �������������������������������� 18�5 BTU/hr

Device and power supply ��� 21�9 BTU/hr

All other models

Device �������������������������������� 17�0 BTU/hr

Device and power supply ��� 21�8 BTU/hr

Extron MLC 226 Series MediaLink ® Controllers • Specifications 2

Mounting

Rack mount

MLC 226 IP DV+ ���������������� No

All other models����������������� Yes, with optional rack mounting kits

Furniture or wall mount

MLC 226 IP DV+ ���������������� Yes

All other models����������������� Yes, with optional mounting kits

Enclosure type

MLC 226 IP, MLC 226 IP DV+ ��� High-impact plastic faceplate, metal rear enclosure

MLC 226 IP AAP, MLC 226 IP L Metal faceplate, metal rear enclosure

Enclosure dimensions

MLC 226 faceplate ������������������ 4�5" H x 6�4" W x 0�1" D (11�4 cm H x 16�3 cm W x 0�3 cm D) (3 gang)

MLC 226 AAP, MLC 226 IP DV+ faceplates

4�5" H x 10�0" W x 0�1" D (11�4 cm H x 25�4 cm W x 0�3 cm D) (5 gang)

MLC 226 L faceplate ���������������� 3�15" H x 6�5" W x 0�1" D (8�0 cm H x 16�5 cm W x 0�3 cm D)

Device

MLC 226 IP DV+ ���������������� 2�75" H x 5�3" W x 2�0" D (7�0 cm H x 13�5 cm W x 5�9 cm D) and

2�7" H x 2�6" W x 0�9" D (6�9 cm H x 6�6 cm W x 2�3 cm D)

(Depth excludes knob and buttons� Fits some 5 gang boxes�

Allow at least 2�1" (5�3 cm) depth in the wall or furniture�)

2.1”

10.1”

5.25"

2.7"

4.5”

E

D

C

B

A

E

D

C

B

A

MLC 226 IP DV+ Rear

All other models����������������� 2�75" H x 5�3" W x 2�0" D (7�0 cm H x 13�5 cm W x 5�9 cm D)

(Depth excludes knob and buttons� Fits some 3 gang boxes)

Extron MLC 226 Series MediaLink ® Controllers • Specifications 3

6.5”

5.25"

2.7"

2.1”

6.4”

5.25"

3.15”

MLC 226 IP L Rear

4.5”

10.1”

5.25"

MLC 226 IP Rear

2.7"

2.1”

2.7"

2.1”

4.5”

MLC 226 IP AAP Rear

Extron MLC 226 Series MediaLink ® Controllers • Specifications 4

Product weight

MLC 226 IP DV+ ���������������������� 1�0 lbs (0�5 kg)

All other models ���������������������� 0�7 lbs (0�3 kg)

Shipping weight

MLC 226 IP DV+ ���������������������� 5 lbs (3 kg)

All other models ���������������������� 4 lbs (2 kg)

Vibration ���������������������������������������� ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

Safety �������������������������������������� CE, c-UL, UL

EMI/EMC ��������������������������������� CE, C-tick, FCC Class A, VCCI, KC mark, ICES

Accessibility ����������������������������� Complies with the appropriate requirements of Section 508 of the

Rehabilitation Act (29 U�S�C� 794d)�

Warranty ���������������������������������������� 3 years parts and labor

NOTE: All nominal levels are at ±10%�

NOTE: Specifications are subject to change without notice�

8�0-011613-D15

Extron MLC 226 Series MediaLink ® Controllers • Specifications 5

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement