Panasonic CQC1120U, CQC1100U, CQC1110U, CQC1200U Operating instructions

Panasonic CQC1120U, CQC1100U, CQC1110U, CQC1200U Operating instructions
E
N
G
L
I
S
H
Power and Sound Controls
Note: If no operation takes place for more than 5 seconds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.
Clock Setting
Power
Audio Mode
(Bass/Treble/Balance/Fader/Sub Woofer)
q Push [SEL] to select the audio mode.
The 12-hour system is used for the clock.
Display Change
Turn the key in the ignition until
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off: Press [SRC](POWER)
again and hold.
1
Press [DISP] (display) to switch to the clock display.
When the power is off:
Volume
No display
ACC
ON
Bass
Treble
Fader
Balance
E
N
G
L
I
S
H
Initial Time
1
2
q Press [DISP] (clock).
Regular mode
Clock display
Sub Woofer
Note: "AdJ" is displayed when the clock is not adjusted.
(➡ page 13)
(Only for CQ-C1200U)
Remote control sensor (➡ page 18)*
(only for CQ-C1200U/C1120U/C1110U)
[k TUNE], [l TUNE] (Hours, minutes)
E / PUSH S
EL
CQ-C1200U
BA
ND
UM
VOL
"AdJ" is displayed when the clock is not
adjusted.
Push
D•M
APM
ND
UME / PUSH SEL
VOL
CQ-C1200U
CLOCK
POWER
C
SR
BA
TUNE
TRACK
D•M
APM
MUTE
7
8
1
2
9
3
10
11
4
5
12
SCAN
6
SQ
REP
DI
SP
TUNE
TRACK
CLOCK
POWER
C
SR
MUTE
MUTE
7
8
1
2
9
3
10
11
4
5
12
6
SCAN
SQ
SQ
REP
SP
DI
w
Turn [VOLUME] clockwise or counterclockwise
to change each level.
Hours
Bass:
SQ indicator
Volume
SQ (Sound Quality)
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
[DISP] (clock)
default: 0 dB
Adjustable range: –12 to +12 (by 2 dB step)
w Press and hold [DISP] (clock) for more than 2
seconds.
Treble:
(Hours blink.)
default: 0 dB
e Press [k TUNE] or [l TUNE].
Press [SQ] to select a sound type as follows:
Volume level (0 to 40)
(default: 18)
Adjustable range: –12 to +12 (by 2 dB step)
(default)
Balance:
R (right speaker) or L (left speaker)
(Hours set.)
Minutes
r Press [DISP] (clock).
Up
SQ -- (default)
flat frequency response:
does not emphasize.
SQ - 1 (ROCK)
speedy and heavy sound:
exaggerates bass and treble.
Down
Mute
Press [MUTE] to mute the sound completely.
SQ - 2 (POP)
MUTE
wide-ranged and deep sound:
slightly emphasizes bass and treble.
ST
SQ - 3 (VOCAL)
lights
Press [MUTE] again to cancel.
clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
• Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,
readjust bass/treble or volume (➡ page 13).
• CQ-C1100U has no remote control function.*
12
CQ-C1200U/C1120U/C1110U/C1100U
Adjustable range: 1 to 15 (by 1 step) Balance center
(default)
Fader:
F (front speaker) or R (rear speaker)
(Minutes blink.)
t Press [k TUNE] or [l TUNE].
(Minutes set.)
y Press [DISP] (clock).
Adjustable range: 1 to 15 (by 1 step)
Sub Woofer:
Fader center
(default)
(Only for CQ-C1200U)
default: 4
Adjustable range (level): MUTE (0) to 7
(End.)
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
Time Reset
Press and hold [DISP] (clock) for more than
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.
CQ-C1200U/C1120U/C1110U/C1100U
13
E
N
G
L
I
S
H
Caution: To ensure safety, never attempt to preset stations while you are driving.
Preset Station Setting
Display Change
E
N
G
L
I
S
H
Up to 6 stations each can be saved in the FM1,
FM2, FM3 and AM preset station memories.
Press [DISP] (display) to switch to the clock display.
4
Radio
Mode
Radio
Press [SRC] (source) to change
3
to the radio mode.
CD player
Radio
FM Stereo indicator
E / PUSH S
EL
Note: Existing saved stations are overwritten with
new stations after following this procedure.
CQ-C1200U
BA
ND
UM
VOL
Frequency
Clock display
D•M
APM
TUNE
TRACK
ST
CLOCK
POWER
C
SR
MUTE
7
8
1
2
9
3
10
11
4
5
12
6
SCAN
SQ
REP
DI
SP
q Band
Press [BAND] to select a desired band.
(➡ page 14)
ND
UME / PUSH SEL
VOL
CQ-C1200U
ND
Band
Press [BAND] to change the band.
BA
BA
D•M
APM
TUNE
TRACK
ST
CLOCK
POWER
C
SR
Tuning
Manual
[l TUNE]: Higher frequency
Seek Tuning
9
3
10
11
4
5
12
SCAN
6
SQ
REP
SP
DI
Press and hold [BAND] (APM: auto preset memory) for more than 2 seconds.
• The 6 stations with good reception will be automatically saved in the memory under preset buttons
from [1] to [6].
• Once set, the preset stations are sequentially scanned for 5 seconds each.
Manual Preset Memory
Direct Memory(D·M)
Your favorite FM/AM radio station can be memorized in the [D·M] button and you can call back the radio station just by
pressing the button whatever the current sound source is, even if the power is off.
Memorize
Use manual or seek tuning to find a station.
(➡ page 14)
Press and hold one of the preset buttons from
[1] to [6] until the display blinks once.
blinks once
Select the station in Radio mode (a above)
¡The direct memoried station is received.
D-M
Press and hold [D·M] until the Frequency display blinks.
D-M
8
2
w Auto Preset Memory (APM)
Press and hold ...
[l TUNE]: Higher frequency
[k TUNE]: Lower frequency
Tuning will automatically stop when the signals of the next
broadcast station are received.
Press [D·M]. (Press again to cancel)
7
1
Preset buttons from [1] to [6]
[k TUNE]: Lower frequency
Recalling the Direct Memory
MUTE
Preset Station Calling
Press the corresponding preset button from
[1] to [6] to tune in a preset station.
lights
D-M
Default: FM 87.9 MHz
blinks
e Release [D·M] button. Then, new station will be
overwritten on existing saved station.
14
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
15
E
N
G
L
I
S
H
E
N
G
L
I
S
H
CD Player
Disc Insert and Playback
Disc insert
5
u (eject)
Playback will start automatically after the player
recognized the loaded disc as an ordinary music
CD. (When a CD-R or CD-RW which has CD-DA
formatted data as the same as an ordinary music
CD is loaded, this player recognizes it as an ordinary music CD.)
“LOAd” will be displayed until the disc is loaded.
Label side
Notes:
• Do not insert a disc when “DISC” indicator
lights.
• The power will be turned on automatically when a
disc is loaded.
Cautions:
• Only 5" (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
• This unit does not support CD text display.
• This unit does not support MP3 and WMA disc playback.
• Refer to page 24 about notes on CD-Rs/RWs.
• This unit is not designed for any 3" (8 cm) disc.
• If you insert an 3" (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then
press [u] (eject).
• Do not use irregularly shaped discs.
• Do not use discs that have a seal or label attached.
• Do not insert foreign matter into the disc slot.
Pause (y / 5)
Direct Track Selection
Press [BAND] (y / 5) to pause.
Press [BAND] (y / 5) again to resume
the playback.
• Press a track number button from
[1] to [6].
The corresponding track starts
playing.
• Press and hold a track number button from [7] to [12] ([1] to [6]) for
more than 1 second.
The corresponding track starts
playing.
UME / PUSH SE
L
CQ-C1200U
BA
ND
VO L
Stop and Disc Eject
D•M
APM
DISC
TUNE
TRACK
TRACK
CLOCK
POWER
C
SR
Press [u] (eject) to stop CD play and eject the disc.
During disc ejection, “EJ” (eject) will be displayed.
MUTE
7
8
11
22
33
10
11
44
55
12
66
SCAN
REP
SQ
DI
SP
Scan PlayC
Listening to a CD
CD Player Mode
<Disc indicator>
• lights when the disc is loaded.
• Do not insert a disc when “DISC”
indicator lights.
Press [SRC] (source) to change to the CD play mode.
Playback will start automatically when a disc is loaded.
Track Selection
Track Search
Press [d TRACK]: Advance to the next track.
Press [s TRACK]: Back to the beginning of the current track.
Back to the previous track. (Press twice.)
Press and hold ...
[d TRACK]: Fast forward
[s TRACK]: Fast reverse
Release to resume the regular play.
CD player
Radio
<CD player display>
Track playing time
BA
ND
UME / PUSH SEL
VOL
Track number
Repeat play
D•M
TUNE
TRACK
DISC
TRACK
CLOCK
POWER
C
SR
MUTE
7
8
1
2
9
3
10
11
4
5
12
6
SCAN
SQ
REP
SP
DI
Random play
Display Change
Press [DISP] (display) to switch to the clock display.
DISC
TRACK
Clock display
Track playing time
track number
CQ-C1200U/C1120U/C1110U/C1100U
• Press [REP].
The current track is repeated.
• Press [REP] again to cancel.
REP: Repeat indicator
• Press and hold [REP] (RANDOM) for
more than 2 seconds.
All the tracks are played in random order.
• Press and hold [REP] (RANDOM) again
to cancel.
R 5 : Random indicator
REP
DISC
TRACK
CQ-C1200U
APM
16
9
6
Scan playC
• Press and hold [SQ] (SCAN), for more than
2 seconds.
The first 10 seconds of each track on the
disc are played in sequence.
• Press and hold [SQ] (SCAN) again to
cancel.
R5
DISC
TRACK
DISC
CQ-C1200U/C1120U/C1110U/C1100U
TRACK
blinks.
17
Only for CQ-C1200U/C1120U/C1110U
E
N
G
L
I
S
H
Remote Control Unit
Anti-Theft System
Battery Installation
This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.
Remove the battery holder.
Pull the battery holder by the position B while pushing position A in the direction indicated by the arrow.
Install the battery on the battery holder.
Place a battery in the holder with its “+” side facing
up as shown in the figure.
Insert the battery holder.
Push the battery holder back into its original position.
7
Battery Notes
E
N
G
L
I
S
H
Lithium battery
8
Back side
1 Remove the removable face plate
Switch off the power of the unit.
Remove the removable face plate.
Position B
Battery holder
Position A
Remove and dispose of an old battery immediately.
Battery Information:
• Battery type: Panasonic lithium battery (CR2025)
• Battery life: Approximately 6 months with normal use (at room temperature)
q Press [
]. The removable face plate will
be opened.
w Push the face plate to either the right or
left.
e Pull it out toward you.
Contact
w
q Press
Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a
fire. Battery leakage may damage the unit.
2 Place the Removable
Face Plate into Case
• Do not disassemble or short the battery. Do not throw a battery into a fire.
• Keep batteries away from children to avoid the risk of accidents.
• Be careful to observe proper local disposal rules when you dispose of batteries.
Gently press the bottom of the case and
open the cover. Place the face plate into
the case and take it with you when you
leave the car.
Control Reference Guide
Removable face plate case
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
Point the remote control unit at the main unit’s sensor.
BA
ND
UME / PUSH SEL
VOL
APM
C
PWR
[MODE]
(Mode (source))
(➡ pages 14, 16)
[BAND]
(Band) (Pause)
(➡ page 14, 17)
POWER
(ATT)
SR
[PWR]
(Power)
(➡ page 12)
MUTE
MODE
VOL
PRG
[MUTE]
(Mute)
(➡ page 12)
MUTE
7
8
1
2
[VOL] [j] [i]
(Volume )
(➡ page 12)
Install Removable Face
Plate
q Slide the left side of the removable face
w
Tab
plate in place.
w Press the right end of the removable
face plate until “click” is heard.
q
BAND/DISC UP
Cutout
TUNE
TRACK
[TUNE] [TRACK] [k] [l] [] []
(Tune/track selection/track search)
(➡ page 14, 17)
Car Audio
Note: CQ-C1100U has no remote control function.
18
9
3
CQ-C1200U/C1120U/C1110U/C1100U
Cautions:
• This face plate is not waterproof. Do not expose it to water or excessive moisture.
• Do not remove the face plate while driving your car.
• Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.
• Do not touch the contacts on the face plate or the main unit, since this may result in poor electrical contacts.
• If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.
CQ-C1200U/C1120U/C1110U/C1100U
19
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Troubleshooting
Preliminary Steps
Check and take steps as described in the tables below.
9
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs.
Never try to repair the unit by yourself because it is dangerous
to do so.
Cautions:
• Do not use the unit if it malfunctions or if
there is something wrong.
• Do not use the unit in irregular condition, for example, without sound, or with
smoke or foul smell, which can cause
ignition or electric shock. Immediately
stop using it and call the store where
you purchased it.
❐ Radio
Trouble
Poor reception or noise
Antenna installation or wiring of antenna cable is faulty.
➡Check whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely
connected to the chassis.
The number of auto preset
stations is less than 6.
The number of receivable stations is less than 6.
➡Move to an area where receivable stations number is maximum, and
try presetting.
❐ Common
Cause/Step
Car’s ignition switch is not on.
➡Turn your car’s ignition switch to ACC or ON.
The power cord (battery, ACC and ground) is connected in the wrong way.
➡Check the wiring.
No power.
Grounding wire is not correctly connected.
➡Connect the grounding wire to a metal part of the car.
❐ CD
Trouble
Mute is set to ON.
➡Set it to OFF.
Noise.
The wiring of the speaker line is not correct, or a break or poor contact
arises.
➡Check the wiring in accordance with the wiring diagram.
Disc is in the CD compartment but no sound is
made, or disc is ejected
automatically.
• Disc is dirty.
• Disc has scratches.
➡Clean disc, referring to the section on “Notes on Discs”.
A disc that has data other than CD-DA type is loaded.
➡Discs that have CD-DA type data should be used.
Condensation (dew).
➡Wait for a while before use.
➡The unit may not successfully play back a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive)
and a disc which are incompatible one another. Refer to instructions for the concerned devices for details.
There is an electromagnetic-wave generator such as a cellular phone near the unit
or its electrical lines.
➡Keep an electromagnetic-wave generator such as a cellular phone away
from the unit and the wiring of the unit. In case that noise cannot be eliminated due to the wiring harness of the car, consult your dealer.
• Disc is dirty.
• Disc has scratches.
➡Clean disc, referring to the section on “Notes on Discs”.
Grounding wire is not correctly connected.
➡Connect the grounding wire to a metal part of the car.
20
Cause/Step
The disc is inserted upside down.
➡Place disc in the correct direction with the label side up.
Fuse is burnt out.
➡Call the store where you purchased the unit, or your nearest
Servicenter (see the attached sheet) and ask for fuse replacement.
No sound.
Cause/Step
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
➡Check the wiring of the antenna amplifier battery lead.
Troubleshooting Tips
Trouble
10
CQ-C1200U/C1120U/C1110U/C1100U
Sound skips, bad sound
quality. (e.g. caused by
noise)
➡The unit may not successfully play back a CD-R/RW that is made up
of a combination of writing software, a CD recorder (CD-R/RW
drive) and a disc which are incompatible with one another. Refer to
instructions for the concerned devices for details.
CQ-C1200U/C1120U/C1110U/C1100U
21
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Troubleshooting (Continued)
❐ CD (Continued)
11
❐ Remote Control Unit
Trouble
Sound skips due to
vibration.
Cause/Step
Trouble
Battery polarities are reversed.
➡Insert the battery correctly.
Instable mounting.
➡Mount the unit securely with the mounting parts, referring to the
section on installation.
Wrong battery.
➡Check the battery.
Disc is not ejected.
Time is counted but no
sound comes out.
The first track of a mix mode disc was reproduced. (Mix mode is a format in which data except music is recorded on the first track and music
data is recorded on other than the first track in a session.)
➡Play back music data recorded on other than the first track.
Buttons are invalid for
operation.
Left and right sounds
are reversed in stereo
listening.
Cause/Step
Battery has run down.
➡Replace the battery.
Remote control unit is in the wrong direction.
➡Direct the remote control unit at sensor on the front panel.
Error Display Messages
❐ CD
Display
❐ Sound Setting
Trouble
12
Cause/Step
Mounting angle is over 30˚.
➡Adjust mounting angle to less than 30˚.
• Disc is defective.
• Mechanical trouble.
➡Press [u] (eject). If normal operation is not restored, call the store
where you purchased the unit or the nearest Servicenter to ask for
repairs.
No sound from left,
right, front or rear
speakers.
Only for CQ-C1200U/C1120U/C1110U
(The disc is ejected automatically)
Left and right balance, or front and rear balance is off on one side.
➡Adjust balance/fader setting as appropriate.
(The disc is ejected automatically)
Cables are not correctly connected.
➡Connect the cables correctly.
Cause/Step
• Disc is dirty, or is upside down.
• A disc that has data other than CD-DA type is loaded.
➡Check the disc.
Disc has scratches.
➡Check the disc.
No operation by some cause.
➡If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs.
The right speaker wire is connected to the left speaker and the left
speaker wire to the right speaker.
➡Connect the speaker wires to the correct ones.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest
authorized Panasonic Servicenter. The product should be serviced only by a qualified technician.
Replace the Fuse
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the product directly without a fuse, could cause fire or damage to the unit.
If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.
22
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
23
E
N
G
L
I
S
H
Maintenance
13
❐ Cleaning this Unit
❐ Caution on Cleaning
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as they
may mar the surface of the unit.
E
N
G
L
I
S
H
Installation
WARNING
Care of the Unit
Notes on discs
Do not play any ordinary music CDs with labels
other than this one.
14
❐ This installation information is designed for experienced installers and is not
intended for non-technical individuals. It does not contain warnings or cautions of
potential dangers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than a qualified
installer could cause damage to the electrical system and could result in serious
personal injury or death.
❐ If your car is equipped with air bag and/or anti-theft systems, specific procedures
How to hold the disc
• Do not touch the underside of the disc.
• Do not scratch the discs.
• Do not bend disc.
• When not in use, keep the disc in the case.
may be required for connection and disconnection of the battery to install this product.
Before attempting installation of this electronic component, contact your car dealer
or manufacturer to determine the required procedure and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN
DAMAGE TO THE VEHICLE AND PERSONAL INJURY.
Label side
Do not use irregularly shaped discs.
Do not leave discs in the following places:
• Direct sunlight
• Near car heaters
• Dirty, dusty and damp areas
• On seats and dashboards
Do not use irregularly shaped discs.
<Right>
<Wrong>
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ballpoint pen stroke.
Notes on CD-Rs/RWs
• You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives),
either due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
• CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs.
Leaving them inside a car for extended periods may damage them and make playback impossible.
• The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a CD recorder (CD-R/RW drive) and a disc if they are incompatible one another.
• This player cannot play the CD-R/RW discs if the session is not closed.
• This player cannot play the CD-R/RW discs which contains other than CD-DA data.
• Be sure to observe the instructions of CD-R/RW disc for handling it.
❐ Overview
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through
the remaining steps:
(Please refer to the “WARNING” statement above.)
• Identify and label the car wires.
• Connect the car wires to the wires of the power
connector.
• Install the unit in the dashboard.
• Check the operation of the unit.
If you encounter problems, please consult your nearest
professional installer.
Caution: This unit operates with a 12 V DC negative ground auto battery system only. Do not
attempt to use it in any other system. Doing so
could cause serious damage.
…Keep for future reference in case the product needs
servicing.
• Installation Hardware…Needed for in-dash installation.
❐ Required Tools
You’ll need a screwdriver, a 1.5 V AA battery, and the following:
12 V DC
Test bulb
Electrical
tape
Side-cut
pliers
❐ Dashboard Specifications
Thickness Min. 3⁄16" (4.75 mm)
Max. 7⁄32" (5.56 mm)
23⁄32" (53 mm)
Before you begin installation, look for the items which are
packed with your unit.
75⁄32" (182 mm)
• Warranty Card…Fill this out promptly.
• Panasonic Servicenter List for Service Directory
24
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
25
E
N
G
L
I
S
H
Installation (Continued)
15
The first step in installation is to identify all the car wires
you’ll use when hooking up your sound system.
As you identify each wire, we suggest that you label it
using masking tape and a permanent marker. This will
help avoid confusion when making connections later.
❐ Identify All Leads
Note: Do not connect the power connector to the stereo
unit until you have made all connections. If there are no
plastic caps on the stereo hooking wires, insulate all
exposed leads with electrical tape until you are ready to
use them. Identify the leads in the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work
with individual leads.
Turn the ignition on to the accessory position, and ground
one lead of the test bulb to the chassis.
Touch the other lead of the test bulb to each of the
exposed wires from the cut radio connector plug. Touch
one wire at a time until you find the outlet that causes the
test bulb to light.
Now turn the ignition off and then on. If the bulb also
turns off and on, that outlet is the car power lead.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for radio
(RADIO), accessory (ACC), or ignition (IGN).
Battery Lead
If your stereo unit has a yellow lead, you will need to
locate the car’s battery lead. Otherwise you may ignore
this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other
function.)
If your car has a radio or is pre-wired for one:
With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the
chassis and checking the remaining exposed wires from
the cut radio connector plug.
26
CQ-C1200U/C1120U/C1110U/C1100U
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for the battery,
usually marked BAT.
Speakers
Identify the car speaker leads. There are two leads for
each speaker which are usually color coded.
A handy way to identify the speaker leads and the speaker
they are connected with is to test the leads using a 1.5 V
AA battery as follows.
Hold one lead against one pole of the battery and stroke
the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a
speaker lead.
If not, keep testing different lead combinations until you
have located all the speaker leads. When you label them,
include the speaker location for each.
Antenna Motor
If your car is equipped with an automatic power antenna,
identify the car motor antenna lead by connecting one
bulb tester lead to the car battery lead and touching the
remaining exposed wires from the cut radio connector
plug one at a time. You will hear the antenna motor activate when you touch the correct wire.
Antenna
The antenna lead is a thick, black wire with a metal plug at
the end.
❐ Connect All Leads
Now that you have identified all the wires in the car, you
are ready to begin connecting them to the stereo unit
wires. The wiring diagram (\ page 30) shows the proper
connections and color coding of the leads.
We strongly recommend that you test the unit before
making a final installation.
You can set the unit on the floor and make temporary connections to test the unit. Use electrical tape to cover all
exposed wires.
carefully to avoid damaging the speakers and the stereo
unit.
The speakers used must be able to handle more than 50
W (CQ-C1200U/C1120U)/45 W (CQ-C1110U/C1100U) of
audio power. If using an optional audio amplifier, the
speakers should be able to handle the maximum amplifier
output power. Speakers with low input ratings can be
damaged. Speaker impedance should measure 4–8 Ω,
which is typically marked on most speakers. Lower or
higher impedance speakers will affect output and can
cause both speaker and stereo unit damage.
E
N
G
L
I
S
H
❐ Final Installation
Lead Connections
Connect all wires, making sure that each connection is
insulated and secure. Bundle all loose wires and fasten
them with tape so they will not fall down later. Now insert
the stereo unit into the mounting collar.
Congratulations! After making a few final checks, you’re
ready to enjoy your new auto stereo system.
16
❐ Final Checks
Motor Antenna
Connect the car motor antenna lead to the dark blue
motor antenna relay control lead.
(Do not confuse the antenna lead with blue/white stripe
lead for a power amplifier.)
1. Make sure that all wires are properly connected and
insulated.
2. Make sure that the stereo unit is securely held in the
mounting collar.
3. Turn on the ignition to check the unit for proper operation.
Battery
Connect the yellow battery lead to the correct radio wire
or to the battery fuse port on the fuse block.
If you have difficulties, consult your nearest authorized
professional installer for assistance.
Antenna
Connect the antenna by plugging the antenna lead into the
antenna receptacle.
Equipment
Connect any optional equipment such as an amplifier,
according to the instructions furnished with the equipment. Leave about 12" (30 cm) of distance between the
speaker leads/amplifier unit and the antenna/antenna
extension cord. Read the operating and installation
instructions of any equipment you will connect to this
unit.
Power
Connect the red power lead to the correct car radio wire
or to the appropriate fuse port on the fuse block.
If the stereo unit functions properly with all these connections made, disconnect the wires and proceed to the final
installation.
Caution: Connect the red power lead last, after
you have made and insulated all other connections.
Ground
Connect the black ground lead of the power connector to
the metal car chassis.
Speakers
Connect the speaker wires. See the wiring diagram
(\ page 30) for the proper hookups. Follow the diagram
CQ-C1200U/C1120U/C1110U/C1100U
27
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Installation (Continued)
❐ Preparation
❐ Installation Hardware
Warning: If your car is equipped with air bag
and/or anti-theft systems, specific procedures
may be required for connection and disconnection of the battery to install this product.
Before attempting installation of this electronic
component, contact your car dealer or manufacturer to determine the required procedure and
strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY.
17
• Disconnect the cable from the negative
battery
terminal (see warning and caution below).
• Remove Mounting Collar q and Trim Plate u from the
main unit temporarily, which are already mounted at
shipment.*
Caution: Various settings that have been stored in the
memory in other on-board equipment (car navigation
etc.) may be lost if the battery terminals are disconnected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the terminals.
After completing installation of the main unit, set the
equipment again according to the record.
No.
Item
Diagram
Q’ty
q
Mounting Collar*
(FX0214C316ZA)
1
w
Hex. nut (5 mmø)
(YJN994C002ZA)
1
e
Rear support strap
(YFG044C002ZA)
1
r
Tapping screw (5 mmø×16 mm)
(XTT5+16AFK)
1
t
Mounting Bolt (5 mmø)
(YEJV014C002A)
1
y
Power Connector
(YEAJ02877)
1
u
Trim Plate*
(YFC054C063ZA)
1
i
Dismounting Plate
(YFX214C323ZA)
2
Cautions:
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
1
First complete the electrical connections, and
then check them for correctness.(a page 30)
The included Mounting Collar q is
designed specially for this unit. Do
not use it to attach any other model.
18
Insert Mounting Collar q into the dashboard, and bend the mounting tabs out
with a screwdriver.
The tabs to be bent vary depending on
the car. To securely install the unit, fully
bend a number of the tabs so that there
is no rattling.
Example:
Tab
q Mounting
Collar
y Power Connector
Mounting Holes
t Mounting Bolt
(a) Using the rear support strap e
Fire wall of car
r Tapping screw
(5 mmø×16 mm)
2
3 mmø
w Hex. nut
(5 mmø)
• Unit should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30°.
Mounting Springs (C)
e Rear support strap
t Mounting bolt (5 mmø)
Establish the rear connection of the unit.
After fixing Mounting Bolt t and Power Connector
y, fix the rear of the unit to the car body by either
method (a) or (b) shown the previous page.
3
Insert Trim Plate u.
4
After installation reconnect the negative
(–) battery terminal.
q Mounting collar
Less than 30°
❐ Dashboard Installation
Installation Opening
This unit can be installed in any dashboard having
an opening as shown below. The dashboard should
be 3 ⁄ 16" (4.75 mm)–7 ⁄ 32" (5.56 mm) thick in
order to be able to support the unit.
23/32"
(53 mm)
75/32"
(b) Using the rubber cushion (option)
Rubber cushion (option)
Rear support bracket
(provided on the car)
t Mounting bolt
(5 mmø)
q Mounting collar
Engage the Mounting
Springs (C) in the
mounting holes of the
Mounting Collar q
firmly.
Mounting
Hole
Mounting Spring
(182 mm)
28
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
29
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Electrical Connections
Only for CQ-C1200U
Cautions:
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Strip about 5 mm of the lead ends for connection.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables
and keep cable terminals free from touching any metal parts.
• Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
19
Only for CQ-C1200U/C1120U/C1110U
20
Sub-Woofer
(option)
External Power Amplifier
CY-M7052
(option)
RCA Cord (option)
External Power Amplifier
CY-M9054
(option)
To remove
the Fuse
Sub-Woofer
cord (monaoural)
S•W-OUT
CQ-C1200U/C1120U
CQ-C1110U/C1100U
(R) Red
(L) White
Fuse
RCA Cord (option)
Antenna
Fuse (15 A)
(L) White
(R) Red
C If the fuse (rear panel) blows frequently, they may be something
wrong with the unit or wiring. Consult
your nearest Panasonic Servicenter
for service.
Preamp. output connector (rear)
Preamp. output connector (front)
y Power connector
Ground lead
To a clean, bare metallic part of car chassis.
System up
speakers
BATTERY 15A
(Black)
Motor antenna relay control lead
(To motor antenna) (Max. 500 mA)
This lead is not intended for use with switch
actuated power antenna.
(Dark blue)
Note: A bridge connection should be
used when connecting only 2 channels
such as CQ-C1100U connection.
C
(Yellow)
ACC
1
3
2
y
Power
connector
Battery lead
To the car battery, continuous +12 V DC
Power lead
To ACC power, +12 V DC
(Red)
Note: The power antenna extends automatically
when the FM/AM radio mode is selected.
Speaker lead
(Dark blue/white stripe)
FRONT SP
(White/
black
stripe) (–)
(White)
(+)
(Gray/black
stripe)
(–)
(Gray)
(+)
REAR SP
(Green/black
stripe)
(–)
(Green)
(+)
(Violet/
black
stripe) (–)
(Violet)
(+)
Speaker connections
L
R
Left speaker
(Front)
30
Right speaker
(Front)
CQ-C1200U/C1120U/C1110U/C1100U
Left speaker
(Rear)
Right speaker
(Rear)
Amp. relay control power lead
(Max. 500 mA)
This lead is for connection to the power
amplifier.
Note: This lead is used for power control
when an external power amplifier is connected. The power supply of a power
amplifier will be activated when turning
on the power of this unit.
L
R
• Do not connect more than one speaker to one set of speaker leads (except for
connecting to a tweeter).
• Do not use a 3-wire type speaker system having a common earth lead.
CQ-C1200U/C1120U/C1110U/C1100U
31
E
N
G
L
I
S
H
To Remove the Unit
1
Specifications
Switch off the power of the unit.
❐ General
Power supply:
Current consumption:
Maximum power output:
21
2
Remove the removable face plate.
q Press [
]. The removable face plate will
be opened.
w Push the face plate to either the right or
left.
e Pull it out towards you.
Contact
w
q Press
3
Remove the Trim Plate u with a screwdriver.
Tone adjustment range:
Bass:
Treble:
Suitable speaker impedance:
Preamp output voltage:
Output impedance:
Sub-Woofer output voltage:
Sub-Woofer output impedance:
Dimensions (W×H×D):
Weight:
12 V DC (11 V–16 V), test voltage 14.4 V, negative ground
Less than 2.2 A (CD play mode; 0.5 W×4 channels)
50 W×4 channels at 1 kHz, volume control maximum (CQ-C1200U/C1120U)
45 W×4 channels at 1 kHz, volume control maximum (CQ-C1110U/C1100U)
22
±12 dB at 100 Hz
±12 dB at 10 kHz
4–8 Ω
2.0 V (CD play mode; 1 kHz, 0 dB)
200 Ω
2.0 V (CQ-C1200U)
200 Ω (CQ-C1200U)
15
7
7"×1 /16 "×5 /8 " (178×50×155 mm)
3 lbs. 1 oz (1.4 kg)
u Trim Plate
Screwdriver
1
2
4
E
N
G
L
I
S
H
q Insert the Dismounting plate i along
the grooves on both sides of the main
unit until “click” is heard.
w Pull out the unit while pushing the plates
further inside.
q Insert
❐ FM Stereo Radio
Frequency range:
Usable sensitivity:
50 dB quieting sensitivity:
Frequency response:
Alternate channel selectivity:
Stereo separation:
Image response ratio:
IF response ratio:
Signal/noise ratio:
87.9 MHz–107.9 MHz
11.0 dBf. (1.25 µV, 75 Ω)
15.2 dBf. (1.6 µV, 75 Ω)
30 Hz–15 kHz (±3 dB)
75 dB
42 dB (1 kHz)
75 dB
100 dB
70 dB
❐ AM Radio
Frequency range:
Usable sensitivity:
Insert the tab
end in the
outer groove.
“Click”
5
Remove the unit by pulling with both hands.
i Dismounting plate
w Pull out
530 kHz–1 710 kHz
28 dB/µV (25 µV, S/N 20 dB)
❐ CD Player
Sampling frequency:
DA converter:
Error correction system:
Pick-up type:
Light source:
Wave length:
Frequency response:
Signal/noise ratio:
Total harmonic distortion:
Wow and flutter:
Channel separation:
8 times oversampling
1 bit DAC system
Panasonic super decoding algorithm
Astigma 3-beam
Semiconductor laser
780 nm
20 Hz–20 kHz (±1 dB)
96 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
Above specifications comply with EIA standards.
Note: Specifications and the design are subject to modification without notice due to improvements in technology.
32
CQ-C1200U/C1120U/C1110U/C1100U
CQ-C1200U/C1120U/C1110U/C1100U
33
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement