CD Boombox with AM/FM Stereo Radio CAUTION: Electrically

CD Boombox with AM/FM Stereo Radio CAUTION: Electrically
CD Boombox with AM/FM Stereo Radio
OWNER’S MANUAL
KT2024A
CAUTION: Electrically Operated Product – Please use care
when plugging into AC outlet.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Caution Marking was located at bottom enclosure of the apparatus
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Cleaning-Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not place this product on an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by
the manufacturer. A product and cart combination should be moved with care-quick stops,
excessive force and uneven surfaces may cause the product and cart combination to
overturn.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that product heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
1
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightening storms or when unused for a long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
This appliance shall not be exposed to dripping or splashing water and that no object filled
with liquids such as vases shall be placed on the apparatus.
Main plug is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the mains
plug should be disconnected form the mains socket outlet completely.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Do not overload wall outlet. Use only power source as indicated.
Use replacement part as specified by the manufacturer.
The product may be mounted to a wall only if recommended by the manufacturer.
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks.
Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instruction.
Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on the product.
Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for
service.
SAVE THESE INSTRUCTIONS
2
CAUTION
Follow the advice below for safe operations.
ON PROTECTION AGAINST LASER ENERGY EXPOSURE
• As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to
disassemble the casing.
• Stop operation immediately if any liquid or solid object should fall into the cabinet.
• Do not touch the lens or poke at it. If you do, you may damage the lens and the player may
not operate properly.
• Do not put anything in the safety slot. If you do, the laser diode will be “ON” when the CD
door is still open.
• If the unit is not to be used for a long period of time, make sure that all power sources are
disconnected from the unit. Remove all batteries from the battery compartment, and unplug
the AC cord from the wall outlet. Make it a practice to remove the AC cord by grasping the
main body and not by pulling the cord.
• This unit employs a laser. The use of controls or adjustment or performance of procedures
other than those specified here may result in exposure to hazardous radiation.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air-flow of the unit by placing it in a place with poor ventilation, by covering
it with a cloth or by placing it on a carpet.
ON CONDENSATION
• When left in a heated room where it is warm and damp, water droplets or condensation may
form inside the unit.
• When there is condensation inside the unit, the unit may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and
dry the unit before use.
Should any trouble occur, remove the power source and refer servicing to qualified personnel.
3
COMPLIANCE WITH FCC REGULATIONS
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio technician for help.
WARNING:
Changes or modifications to this unit not expressively approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PROTECT YOUR FURNITURE!!
This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when
you operate the controls. These ‘feet’ are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain types of oil
based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to
soften, and leave marks or a rubber residue on the furniture.
To prevent any damage to your furniture we strongly recommend that you purchase small selfadhesive felt pads, available at hardware stores and home improvement centers everywhere,
and apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine
wooden furniture.
4
LOCATION OF CONTROLS
5
1. CD Door
2. Play/Pause Button
3. Skip+/Search Forward Button
4. Skip-/Search Backward Button
5. Function Switch (OFF/CD/FM/AUX/AM)
6. Stop Button
7. Program (PROG) Button
8. Repeat (REP) Button
9. FM Stereo Indicator
10. Power Indicator
11. LED Display
12. Play/Prog Indicator
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Repeat Indicator
Volume Control
Tuning Control
AUX-IN Jack
AC Cord
Battery Compartment Door
Telescopic Antenna
Speaker
Speaker
CD Door Open/Close
Dial Scale
POWER SOURCES
This unit operates on AC 120V~ 60Hz or 8 pieces of 1.5V “C” (UM-2) batteries. Do not attempt
to operate the radio on any other power source. You could cause damage to the unit and void
your warranty.
Please be sure the power outlet you plug this unit into is working and receives constant
(unswitched) power.
A.
1.
2.
3.
4.
5.
6.
7.
8.
9.
BATTERY OPERATION
Remove the Battery Door.
Following the polarity diagram as shown in the battery compartment insert 8 x ‘LR14’ (‘C')
batteries then replace the battery door.
IMPORTANT: Be sure that the batteries are installed correctly. Wrong polarity may
damage the unit.
Use only the size and type of batteries specified.
For better performance and longer operating time, we recommend the use of alkaline-type
batteries.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
If the unit is not to be used for an extended period of time, remove the batteries. Old or
leaking batteries can cause damage to the unit and may void the warranty.
Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow battery manufacturer’s directions).
Do not dispose of batteries in fire, batteries may leak or explode.
BATTERY REPLACEMENT
When the output sound of this unit becomes distorted or the CD player operation appears
unstable, the batteries are weak. You need to replace all the exhausted batteries at the same
time as soon as possible to avoid battery leakage.
B.
AC OPERATION
When the AC power cord is plugged into to a wall outlet with AC 120V ~ 60Hz power
supply, the unit will disconnect the batteries automatically, and operate from AC power
instead.
6
IMPORTANT:
This unit has a polarized AC plug with one wide blade and one
narrow blade. This plug will only fit into a matching polarized AC
outlet. This is a safety feature to reduce the possibility of electric
shock. If this plug will not fit in your AC outlet, you probably have
an outdated non-polarized outlet. You should have your out-dated
outlet changed by a qualified, licensed electrician. Do not file the
wide blade on the plug, or use an adaptor to make the plug fit onto
your outlet. This defeats the safety feature and could expose you
to electric shock.
1.
2.
3.
4.
RADIO OPERATION
Slide the FUNCTION SWITCH to “FM” or “AM” as desired. The POWER Indicator will light.
Rotate the TUNING CONTROL to your desired radio station according to the DIAL SCALE
on the unit.
Rotate the VOLUME CONTROL to adjust to the desired output level.
To turn off the radio, slide the FUNCTION SWITCH to “OFF”. The POWER Indicator will go
off.
TIPS FOR BEST RECEPTION
AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change
the position of unit until the internal antenna picks up the strongest signal.
FM – If a stereo broadcast program is being received, the FM STEREO INDCATOR will light.
During FM or FM Stereo reception, always keep
the FM TELESCOPIC ANTENNA fully
extended for best performance. However, if FM reception is weak, try repositioning the
unit near an open window until you get the best reception.
CD OPERATION
NOTE: THIS UNIT NOT ONLY PLAYS COMMERCIAL COMPACT DISCS BUT ALSO
SELF-COMPILED CD-RW DISCS.
• Because of non-standardized format definition/production of CD-R/RW, playback quality
& performance is not guaranteed.
• Manufacturer is not responsible for the playability of CD-R/RW due to recording
conditions such as PC performance, writing software, media properties etc.
• Do not attach a label or seal to either side of the CD-R/RW disc. It may cause a
malfunction.
PLAY MODE
1.
2.
3.
4.
Slide the FUNCTION SWITCH to the “CD” position. The POWER INDICATOR will light.
Open the CD DOOR, load a CD with the label side facing upward and then close the CD
door.
A few seconds later the total number of tracks on the CD will appear on the LED DISPLAY.
Press the PLAY/PAUSE BUTTON to start playing the CD from the first track. The
PLAY/PROG INDICATOR will light steadily.
7
5.
6.
7.
8.
While playing, press the PLAY/PAUSE BUTTON once to pause, the LED DISPLAY will
flash. Press PLAY/PAUSE BUTTON again to resume playing.
Adjust the VOLUME CONTROL to the desired volume level.
Press STOP BUTTON to stop playing.
To turn off the CD player, slide the FUNCTION SWITCH to “OFF”. The POWER
INDICATOR will go off.
NOTE:
If skipping occurs during CD play, try turning the volume down.
Do not open the CD DOOR when a CD is playing.
REPEAT MODE
Repeat 1
When the REPEAT BUTTON is pressed once, the REPEAT INDICATOR will light and blink
continuously. The current track will be repeated until it is interrupted.
Repeat All
When the REPEAT BUTTON is pressed twice, the REPEAT INDICATOR will light steadily. The
whole disc will be played continuously.
To Cancel the Repeat Function: Press the REPEAT BUTTON until the repeat indicator goes
off.
SKIP AND SEARCH MODE
1. During Play or Pause mode, tap the SKIP + or SKIP - BUTTON to go to the next track or go
back to the beginning of the current track.
2. During Play mode or Pause mode, press and hold the SKIP + or SKIP - BUTTON to search
within the current track with audible high speed playback.
PROGRAM PLAY MODE
This function allows music tracks to be played in a programmed sequence.
NOTE: Program can only be set in STOP mode.
1.
Press the PROGRAM BUTTON once. Both Program Number “01” and the PROGRAM
INDICATOR will flash.
2.
Press the SKIP + or SKIP - BUTTON to select the track to be programmed.
3.
Press the PROGRAM BUTTON again to store the selection. The Program Number will
advance to “02” and flash to prompt for the next input.
4.
You may repeat steps #2 to #3 to program up to 20 tracks. As soon as you have entered
the 20th track, the LED DISPLAY will automatically show the programmed tracks one by
one in their correct sequence starting from the first. At the end of program review, Program
Number “01” and the PROGRAM INDICATOR will both flash.
5.
Press the PLAY BUTTON to complete and start program play. Press the STOP BUTTON
to stop.
6.
To review/edit the programmed tracks during play, press the STOP BUTTON and then the
PROGRAM BUTTON, the LED DISPLAY will automatically show the programmed tracks
one by one in their correct sequence starting from the first. At the end of program review,
Program Number “01” and the PROGRAM INDICATOR will both flash. If you do not want to
change any track in the program, press PLAY BUTTON.
7.
To edit a programmed track, first press the PROGRAM BUTTON until you reach the
program number whose track you want to change then press the SKIP+ or SKIPBUTTON to select a new track and press PROGRAM BUTTON again to confirm.
8
8.
9.
To cancel program play, press the STOP BUTTON twice while reviewing programmed
tracks or open the CD DOOR in STOP mode.
To turn off the CD player, slide the FUNCTION Switch to “OFF”. The POWER Indicator will
go off.
AUX IN OPERATION
This CD Player includes an AUX IN JACK so you can enjoy your iPod, MP3 Player or other
audio device.
1. Connect the headphone jack of your external device and the AUX IN jack located on the
back of this CD player. (The connection cable is not included.)
2. Turn on the CD player and it will enter the AUX function mode once the AUX IN jack is
plugged.
3. Start to play your iPod, MP3 player or other audio device.
4. Slowly adjust both the volume controls on your CD player and the external device.
5. Turn off your iPod, MP3 player etc. when you finished listening. Turn the CD player off and
unplug the AUX IN jack.
Remark: Once the AUX IN jack is plugged, the CD player will enter the AUX mode
automatically no matter the FUNCTION Switch is in CD, FM or AM mode. Remember to
disconnect the connection cable from the CD player after use in order to be able to listen to CD
music, FM or AM broadcasts again.
1.
2.
3.
4.
5.
6.
CARE AND MAINTENANCE
Children should be supervised when using this appliance.
Never wrap the earphone lead around any animal or person. Special care should be taken
with long wires.
Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
If drop-outs or interruptions occur in the music during CD play, or if
the CD fails to play at all, its bottom surface may require cleaning.
Before playing, wipe the disc from the center outwards with a good
soft cleaning cloth.
9
TROUBLESHOOTING GUIDE
If you experience difficulties in the use of this music system please check the following or call 1800-777- 5331 for Customer Service.
Symptom
Noise or sound
distorted on AM or FM
broadcast
Possible Cause
CD skips while playing
- Station not tuned properly for AM or
FM.
- FM: FM telescopic antenna is not
extended.
- AM: The bar antenna is not positioned
correctly
- Unit not in “AM” or “FM” function
mode.
- Volume set at minimum
- Unit not in CD function mode.
- CD is not loaded properly.
- If the CD is self-compiled, the media
used may not be compatible with
the player.
- Exhausted battery
- Disc is dirty or scratched.
Intermittent sound from
CD player
- Dirty or defective disc
- Dirty pick up lens
AM or FM no sound
CD player will not play
Sound appears
distorted at high
volume setting
- Player is subject to excessive shock
or vibration
- Volume control is set to maximum.
- Batteries become low
10
Solution
- Retune the AM or FM broadcast
station.
- FM: Extend FM telescopic antenna.
- AM: Reposition the unit until the
best reception is obtained.
- Slide Function Switch to “AM” or
“FM” position.
- Increase Volume.
- Select CD function mode.
- Load CD with label side up.
- Use better quality blank media and
retest.
- Replace all old batteries.
- Wipe CD with clean cloth or use
another disc.
- Clean or replace the defective disc.
- Use a CD lens cleaning disc to
clean the lens.
- Relocate the player away from
shock or vibration.
- Adjust Volume Control to a lower
comfortable level.
- Replace all the old batteries with
new ones.
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U.S.A ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective
materials or factory workmanship for a period of 90 days from the date of original customer purchase and
provided the product is utilized within the U.S.A. This warranty is not assignable or transferable. Our
obligation under this warranty is the repair or replacement of the defective unit or any part thereof, except
batteries, when it is returned to the SPECTRA Service Department, accompanied by proof of the date of
original consumer purchase, such as a duplicated copy of a sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty service. If the
product is repaired or replaced under warranty, the return charges will be at SPECTRA’s expense. There
are no other express warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is demonstrated
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the descriptions
and warnings covered within the owner’s manual or non-SPECTRA approved modifications
c. Claims are made within the warranty period
2. This warranty does not cover damage or equipment failure caused by electrical wiring not
in compliance with electrical codes or SPECTRA owner’s manual specifications, or failure to
provide reasonable care and necessary maintenance as outlined in the owner’s manual.
3. Warranty of all SPECTRA products applies to residential use only and is void when products are used
in a nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the unit carefully and send it
prepaid by insured parcel post or UPS to SPECTRA at the address shown below. IF THE UNIT IS
RETURNED WITHIN THE WARRANTY PERIOD shown above, please include a proof of purchase
(dated cash register receipt) so that we may establish your eligibility for warranty service and repair of the
unit without cost. Also include a note with a description explaining how the unit is defective. A customer
service representative may need to contact you regarding the status of your repair, so include your name,
address, phone number and e-mail address to speed the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $15.00 to cover the
cost of repair, handling and return postage. All out of warranty returns must be sent prepaid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by e-mail at
[email protected] for updated information on the unit requiring service. In some cases the model you
have may be discontinued and SPECTRA reserves the right to offer alternative options for repair or
replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL60634, USA.
1-800-777-5331
To register your product, visit the link below on the website to enter your information.
http://www.spectraintl.com/wform.htm
Printed in China
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement