Enterprise Edge ATA 2 User Guide

Enterprise Edge ATA 2 User Guide
Enterprise Edge ATA 2
User Guide
www.nortelnetworks.com
© 2000 Nortel Networks
P0908546 Issue 02
Contents
About Enterprise Edge ATA 2 5
What does Enterprise Edge ATA 2 do? 5
Feature List 6
Alternate Line 6
Call Forward 6
Call Park 6
Call Park Retrieve 6
Callback for Call Park 6
Call Pick-up (Directed) 6
Call Pick-up (Group) 6
Call Queuing 7
Camp-on 7
Conference Call 7
Conference Hold 7
Conference Consultation (Split Conference) 8
Disconnecting One Party 8
Hold Call (Exclusive) 8
Hold Call (Public) 8
Hotline 8
Last Number Redial 9
Line Pool Selection 9
Enterprise Edge Voice Messaging 9
Page (General) 9
Page (Intercom) 9
Page (External) 9
Page (Intercom/External) 9
Priority Call 10
Privacy Control 10
Restriction Override 10
Ring Again 10
Reply To a Ring Again Signal 10
Saved Number Redial 11
Send Message 11
Service Mode 11
System Speed Dial 11
Tones 11
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
4 Contents
Transfer 12
Blind Transfer 12
Transfer using announce 12
Transfer using Conference 12
To Transfer an external call to a co-worker with a line appearance using
Hold 12
Trunk Answer from any Telephone 13
Voice Call 13
Data Communication 15
Set Tones to OFF 15
Auto-answer Modems and Answering Machines 15
Modem and FAX Transmission Compatibility 15
Troubleshooting for Data Applications 17
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
About Enterprise Edge ATA 2
What does Enterprise Edge ATA 2 do?
Enterprise Edge Analog Terminal Adapter 2 (Enterprise Edge ATA 2) connects a
digital two-line display telephone port to a standard analog voice device, such as a
single-line telephone or a data communication device, such as a modem or facsimile
machine. Enterprise Edge ATA 2 provides on or off-premise service.
This guide describes:
•
Enterprise Edge ATA 2 features used with the Enterprise Edge server
•
Data Communication information
•
Troubleshooting
All of the features available from Enterprise Edge ATA 2 are accessed by pressing
˚• on your telephone and pressing a feature or access code. The feature
list shows ˚• and the feature code. Where applicable, steps are included
to help use each feature. If your telephone does not have a ˚ button, you
must use the hook switch (located under the handset). The hook switch must be
pressed for approximately one half of one second.
If your telephone does not have a • or £ button, you must use dialpad numbers.
To indicate a • press ⁄. To indicate a £ press ‹.
For more information about feature operations, accessing feature operations or
feature codes, see your System Administrator.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
6 About Enterprise Edge ATA 2
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Feature List
Alternate Line
˚¤
Allows you to switch between your two intercom lines. When a line is in use, you
hear an error tone informing you that the line is already in use.
Call Forward
˚•›
Directs your calls to another telephone connected to your Enterprise Edge system.
Press the feature code followed by the extension number of the telephone to receive
the forwarded calls.
To cancel Call Forward, press ˚£›.
Call Park
˚•‡›
Parks the call on hold and allows it to be retrieved from any other telephone within
the system. When the call park is successful, you hear a confirmation tone and the
call is parked on the highest numbered park code in the system. If call park is
unsuccessful, you hear an error tone and remain connected with the call.
Note: Tones must be ON. For a list of park codes, see your System Administrator.
Call Park Retrieve
A parked call can be retrieved from any Enterprise Edge telephone by lifting the
handset and pressing the Call Park code.
Callback for Call Park
Alerts you to the external call you parked and that has remained unanswered for a
set period of time. If your telephone is not in use, callback causes your telephone to
ring. If your telephone is in use, you hear the callback tone over the handset.
Call Pick-up (Directed)
˚•‡fl <plus the ringing number>
Allows you to answer a ringing telephone within your Enterprise Edge system.
Call Pick-up (Group)
˚•‡fi
Allows you to answer any ringing telephone within your Enterprise Edge pick-up
group.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
8 Feature List
Call Queuing
˚•°‚⁄
Allows you to answer the first incoming external call to your telephone, while you
are on a call. All other incoming callers hear a busy signal unless there is another
telephone programmed to ring on the same line.
Camp-on
˚•°¤ <plus the extension number>
Allows you to reroute an external call or a call from a Centrex system telephone to
another Enterprise Edge system telephone.
Conference Call
˚•‹
Allows you to establish a three-way conference between yourself, one external call
and one intercom call, or two intercom calls. Line pool access allows you to
establish a conference between yourself and two external calls.
To establish a conference call:
1. Make or answer the first call.
2. Press ˚¤. This automatically places the first call on hold.
3. Make or answer the second call.
4. Press ˚•‹ to complete the conference.
Note: If the second call is busy, replace the handset and press ˚¤
to return to the first call.
Conference Hold
Allows you to put the two conferenced parties on hold. The held callers are still
conferenced.
To put the conference on hold:
1. Press ˚¤ to put the two conferenced parties on hold.
2. Press ˚¤ to restore the three-way call.
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Feature List 9
Conference Consultation (Split Conference)
Allows you to put one party on hold and consult with the other party.
To consult:
1. Press ˚£‹ to split the conference.
2. Press ˚¤ to alternate between calls.
3. Press ˚•‹ to restore the three-way call.
Disconnecting One Party
Allows you to disconnect one party in a three-way conference call.
To disconnect one call:
1. Press ˚£‹ to put one caller on hold. You are connected with the
other call.
2. Replace the handset.
3. Lift the handset and press ˚¤. You are connected with the caller
on hold.
Hold Call (Exclusive)
˚•‡·
Allows you to place an active call on hold and prevents it from being picked up from
other telephones. When Tones is ON, a held call reminder tone is heard.
Hold Call (Public)
˚¤
Allows you to place an active call on hold and allows it to be picked up from other
telephones. When Tones is ON, a held call reminder tone is heard.
To retrieve a call on hold:
1. Press ˚¤.
Hotline
Allows you to automatically call a programmed internal or external telephone
number. To use the Hotline feature, lift the handset of the designated hotline
telephone.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
10 Feature List
Last Number Redial
˚•fi
Automatically dials the last external telephone number you dialed.
Line Pool Selection
Allows several telephones to access a group of exchange lines. To access line pool
selection, enter the line pool code or during the intercom dial tone press:
˚•› <plus the line pool code>.
Enterprise Edge Voice Messaging
Press the Enterprise Edge Voice Messaging extension, or ˚•·°⁄
<and follow the voice prompts>. Allows you to access your mailbox.
˚•·°‚ <and follow the voice prompts>.
Allows you to leave a message.
˚•·°› <and follow the voice prompts>.
Allows you to forward a call to Enterprise Edge Voice Messaging.
˚•·°fl <and follow the voice prompts>.
Allows you to transfer a call to a mailbox.
˚•·°‡ <and follow the voice prompts>.
Allows you to interrupt a caller who is leaving a message in your mailbox.
˚•·‚› <and follow the voice prompts>.
Allows an agent to login to or logout from a call center.
Note: You cannot use a single line telephone attached to Enterprise Edge ATA 2
for Enterprise Edge Voice Messaging configuration tasks. For more
information about accessing Enterprise Edge Voice Messaging features, see
the Enterprise Edge Voice Messaging Reference Guide.
Page (General)
˚•fl‚ <plus code 1-3> <plus zone code 0-6>
Allows you to make an announcement to all Enterprise Edge telephones
programmed to receive a page, as well as any other connected paging equipment.
You must press a paging zone. For a list of page zones, see your System
Administrator.
Page (Intercom)
˚•fl⁄ <plus zone code>
Page (External)
˚•fl¤
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Feature List 11
Page (Intercom/External)
˚•‹ <plus zone code>
Priority Call
˚•·
Allows you to interrupt an internal call in progress on a digital telephone, or make
a voice call to a digital telephone on Voice Call Deny or Do Not Disturb. The
session in progress is automatically put on hold.
Note: Priority Call must be enabled in Enterprise Edge System Administration.
Privacy Control
˚•°‹
Prevents another telephone that shares your line from joining your current call or
permits another telephone that shares your line to join in.
Restriction Override
˚•fl° <plus an override password> <plus the restricted number>
Allows you to override restrictions imposed on your telephone.
Ring Again
˚•¤
Allows you to queue a call to another Enterprise Edge or Centrex telephone that is
busy or is not answered or to a busy line in the Line Pool. You can use ring again
only on calls placed on an intercom line. When the telephone is available, you are
alerted with one short ring from your telephone.
To cancel ring again, press ˚£¤.
Reply To a Ring Again Signal
To connect with a ring again request when you are on a call (or your telephone is
off-hook):
1. Press ˚¤. This automatically places your call on hold.
2. To return to the caller on hold, press ˚¤.
To connect with a ring again request when your telephone is on-hook:
1. Lift the handset. The ring again number is automatically redialed.
Note: If you do not respond to a ring again signal within 30 seconds, ring
again is canceled.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
12 Feature List
Saved Number Redial
˚•fl‡
Allows you to save an external number while you are on a call or while the called
telephone is ringing. To automatically redial the saved number:
1. Press ˚•‡.
Send Message
˚•⁄
Allows you to leave a message on a co-worker’s telephone.
To cancel send message, press ˚£⁄.
Service Mode
In service mode the Enterprise Edge ATA 2 telephone can be assigned as the control
telephone for one or more lines, or as the night zero telephone. Service mode is
assigned during Enterprise Edge System Administration.
System Speed Dial
˚•‚ <plus the speed dial code>
Allows you to use a speed dial code to quickly dial preprogrammed telephone
numbers. System speed dial codes are established by the System Administrator.
Note: You cannot program personal speed dial numbers from your telephone.
Tones
˚•°‚·
Call progress tones are audio signals heard through the handset or telephone ringer.
Tones signal you about the progress of certain features.
To cancel tones, press ˚£°‚·.
Note: Tones must be OFF when Enterprise Edge ATA 2 is used with a data
communication device such as a FAX or modem.
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Feature List 13
Transfer
Allows you to transfer a call. To transfer a call you must have an available intercom
line.
Blind Transfer
1. Press ˚•‡‚.
2. Press the transfer destination number.
3. Replace the handset.
Transfer using announce
1. Press ˚•‡‚ (intercom dial tone is heard).
2. Press the transfer destination number.
3. Announce the call to the receiving party (optional).
4. Replace the handset.
Transfer using Conference
1. Press ˚¤.
2. Make the second call.
3. ˚•‹.
4. Replace the handset.
To Transfer an external call to a co-worker with a line appearance using Hold
1. Put the caller on hold and select your alternate line.
2. Call your co-worker. Tell your co-worker the flashing line appearance is a call
for them.
3. Replace the handset.
Note: Your co-worker must have an Enterprise Edge telephone with line
appearance.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
14 Feature List
Trunk Answer from any Telephone
˚•°‚‚
Allows you to pick up a ringing external call on a line that has been placed into any
service mode.
Voice Call
˚•flfl <plus the intercom number>
Allows you to make a voice announcement or begin a conversation through the
speaker of a digital telephone without making the other telephone ring.
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Data Communication
This section supplies additional information for using Enterprise Edge Analog
Terminal Adapter 2 with data communication devices.
Set Tones to OFF
Enterprise Edge ATA 2 must have tones OFF so tones do not interfere with data
transmissions.
The following progress tones are not heard when Enterprise Edge ATA 2 is in the
tones OFF mode:
•
Held Line Reminder
•
Call Waiting
•
Ring Again
To turn tones OFF:
Lift the handset and press ˚£°‚·.
Auto-answer Modems and Answering Machines
Enterprise Edge ATA 2 can be connected to a modem or an answering machine as
well as a telephone. It can be programmed to ring in combination with a telephone
connected to one external line on the Enterprise Edge system. It can also be
designated as the Night Set to answer calls after hours. To assign an external line to
ring at a telephone connected to an Enterprise Edge ATA 2, contact your Installer
or System Administrator.
Modem and FAX Transmission Compatibility
Enterprise Edge ATA 2 is compatible with all commercial FAX and modem
protocols. When connected to Enterprise Edge ATA 2, the Enterprise Edge server
supports data transmission rates up to and including 28.8 kbit/s.
Note: The maximum data transmission rate is subject to the quality of the end-toend channel and cannot be guaranteed.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
16 Data Communication
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Troubleshooting for Data Applications
If you are having trouble, check the following before calling a repair person:
1. Make sure the data parameters (parity, baud) are set correctly.
2. Make sure Enterprise Edge Analog Terminal Adapter 2 is in the tones OFF
mode.
3. Make sure you are dialing out on the proper line. The proper line is either an
intercom or external line. See Alternate Line on page 7 of the Feature List. To
change your prime line, see your System Administrator.
4. Substitute a single line telephone for your data communication device. If you
receive a dial tone on the single line telephone, the problem can be with the
data communication device.
P0908546 Issue 02
Enterprise Edge ATA 2 User Guide
18 Troubleshooting for Data Applications
Enterprise Edge ATA 2 User Guide
P0908546 Issue 02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement