N163067 man saw DW743N GB A4.indd

N163067 man saw DW743N GB A4.indd
www.
.eu
DW743N
English (original instructions)
9
Copyright DEWALT
2
10 11
14
13
12
39
3
6
8
7
5
4
2
1
9
40
A1
14
15
16
22
20
17
18
19
21
A2
1
25
26
24
27
23
22
A3
34
30 31
28
A4
2
35
33 32
29
A5
36
37
29
A6
A7
38
A8
X
B
3
46
47
48
49
18
C2
C1
50
20
2
E1
56
23
55
52
D
4
E2
60
58
59
57
F1
F2
62 63
64
22
8
60 61
67
65
F3
G1
7
66
62
4
52
68
70
70
69
G2
H
66
62
22
71
I1
I2
5
72
7
J1
J2
73
74
K1
22
K2
77
76
75
16
12
2
L2
L1
16
62
16
3-8 mm
M
6
N
76
25
20
26
79
80
81
78
O
Q
77
P
R
17
S
T
82
U
81
V1
7
85
85
84
83
V3
V2
W
34
X
8
ENGLI SH
FLIP-OVER SAW DW743N
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough
product development and innovation make DEWALT one of the most
reliable partners for professional power tool users.
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN 61029
and may be used to compare one tool with another. It may be used for
a preliminary assessment of exposure.
WARNING: The declared vibration emission level
represents the main applications of the tool. However if
the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level
over the total working period.
Technical Data
Voltage
(UK & Ireland only)
Type
Power input
230 V tools
115–120 V tools
No-load speed
Blade diameter
Blade bore
Blade body thickness
Blade tooth thickness
Riving knife thickness
Mitre (max. positions)
Bevel (max. positions)
Automatic blade brake time
Weight
V
V
W
W
min-1
mm
mm
mm
mm
mm
left
right
left
s
kg
Cutting capacities
Mitre saw mode (fig. B)
Cutting angle
Straight cross-cut
Table turned 45° right for mitre cuts
Table turned 45° left for mitre cuts
Sawhead tilted 45° left for bevel cuts
DW743N
QS/GB
230
230/115
4
DW743N
LX
–
115
4
2000
1700
2850
250
30
2.2
3
2.3
45°
45°
45°
< 10
37
2000
1700
2850
250
30
2.2
3
2.3
45°
45°
45°
< 10
37
Size of material
H mm
Notes
B mm
20
180
30
40
68
85
176
170
140
26
70
20
50
95
130
140
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of
work patterns.
Fuses:
Europe
U.K. & Ireland
U.K. & Ireland
230 V tools
230 V tools
115 V tools
10 Amperes, mains
13 Amperes, in plugs
16 Amperes, mains
NOTE: This device is intended for the connection to a power supply
system with maximum permissible system impedance Zmax of 0.30 Ω
at the interface point (power service box) of user’s supply.
The user has to ensure that this device is connected only to a power
system which fulfils the requirement above. If necessary, the user can
ask the public power supply company for the system impedance at the
interface point.
Definitions: Safety Guidelines
Workpiece
place against
fence (X)
No packaging
piece required
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
NOTICE: Indicates a practice not related to personal
injury which, if not avoided, may result in property
damage.
Cross-cut at
max. height
Denotes risk of electric shock.
Denotes risk of fire.
Bench Saw mode
Max. ripping capacity left/right
Depth of cut at 90°
Depth of cut at 45°
mm
mm
mm
210/210
0–62
0–32
210/210
0–62
0–32
dB(A)
dB(A)
dB(A)
dB(A)
93
3
106
2.9
93
3
106
2.9
Denotes sharp edges.
EC-Declaration of Conformity
LPA
KPA
LWA
KWA
(sound pressure)
(sound pressure uncertainty)
(sound power)
(sound power uncertainty)
Vibration total values (triax vector sum) determined according to EN 61029-1
and EN 61029-2-11.
Vibration emission value ah
ah =
Uncertainty K =
m/s²
m/s²
2.0
1.5
2.0
1.5
MACHINERY DIRECTIVE
DW743N
DEWALT declares that these products described under technical data
are in compliance with:
2006/42/EC, EN 61029-1, EN 61029-2-11.
These products also comply with Directive 2004/108/EC and
2011/65/EU. For more information, please contact DEWALT at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of DEWALT.
9
EN GL I S H
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Horst Grossmann
Vice President Engineering and Product Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
01.11.2011
Safety Instructions
WARNING! When using electric tools basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury
including the following.
Read all these instructions before attempting to operate this product
and save these instructions.
SAVE THIS MANUAL FOR FUTURE REFERENCE
General Safety Rules
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g., in the
presence of flammable liquids and gases.
3. Guard against electric shock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g., high humidity, when metal swarf is being
produced, etc.), electric safety can be improved by inserting an
isolating transformer or a (FI) earth-leakage circuit-breaker.
4. Keep other persons away.
Do not let persons, especially children, not involved in the work,
touch the tool or the extension cord and keep them away from the
work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was
intended.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing
accessories. Inspect tools periodically and if damaged have
them repaired by an authorized service facility. Keep handles and
switches dry, clean and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories
such as blades, bits and cutters, disconnect tools from the power
supply.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that adjusting keys and
wrenches are removed from the tool before operating the tool.
17. Avoid unintentional starting.
Do not carry the tool with a finger on the switch. Be sure that the
tool is in the “off” position before plugging in.
18. Use outdoor extension leads.
Before use, inspect the extension cable and replace if damaged.
When the tool is used outdoors, use only extension cords intended
for outdoor use and marked accordingly.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired or under the influence of drugs or alcohol.
20. Check for damaged parts.
Before use, carefully check the tool and mains cable to determine
that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual. Have
defective switches replaced by an authorized service centre.
Do not use the tool if the switch does not turn it on and off.
Never attempt any repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may present
a risk of personal injury.
21. Have your tool repaired by a qualified person.
This electric tool complies relevant safety rules. Repairs should
only be carried out by qualified persons using original spare parts;
otherwise this may result in considerable danger to the user.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do
not use tools for purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
9. Use protective equipment.
Always use safety glasses. Use a face or dust mask if working
operations create dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection at all times. Wear a safety helmet at all times.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly
used.
11. Do not abuse the cord.
Never yank the cord to disconnect it from the socket. Keep the
cord away from heat, oil and sharp edges. Never carry the tool by
its cord.
12. Secure work.
Where possible use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to operate the tool.
10
Additional Safety Rules for Flip-over Saws
• Do not allow untrained people to operate this machine.
• Do not use the saw to cut materials other than wood or similar
materials.
• Select the correct saw blade for the material to be cut.
• Do not use cracked or damaged saw blades.
• Do not use HIGH SPEED STEEL blades.
• Use correctly sharpened blades. Observe the maximum speed
marked on the saw blade. The marked speed must always be
equal to or greater than the no-load speed of the machine specified
under technical data.
• Do not use any spacers and spindle rings to make a blade fit onto
the spindle.
• Ensure that the saw blade is mounted correctly before use.
• Make sure that the blade rotates in the correct direction. Keep the
blade sharp.
• Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the technical
data. Use only the blades specified in this manual, complying with
EN 847-1.
• Consider applying specially designed noise-reduction blades.
ENGLI SH
• Disconnect the machine from the mains supply before leaving the
working place.
• Do not use the saw without the guards and riving knife in position
and properly maintained, especially when changing from mitre saw
mode to bench saw mode, or vice versa.
• Make sure the floor area around the machine is level, well
maintained and free of loose materials, e.g. chips and cut-offs.
• Make sure adequate general or localized lighting is provided.
• Wear suitable personal protective equipment when necessary,
including:
– hearing protection to reduce the risk of induced hearing loss;
– respiratory protection to reduce the risk of inhalation of harmful
dust;
– gloves for handling saw blades and rough material. Saw blades
should be carried in a holder wherever practicable.
• Before making any operation ensure the machine is located on an
even and stable surface.
• Refrain from removing any cut-offs or other parts of the work piece
from the cutting area while the saw is running and the saw head is
not in the rest position.
• Select the correct blade for the material to be cut.
• Use a holder or wear gloves when handling a saw blade or rough
material.
• Raise the blade from the kerf in the workpiece prior to releasing the
switch.
• Ensure that the arm is securely fixed when performing bevel cuts.
• Do not wedge anything against the fan to hold the motor shaft.
• The blade guard on your saw will automatically raise when the arm
is brought down; it will lower over the blade when the arm is raised.
The guard can be raised by hand when installing or removing saw
blades or for inspection of the saw. Never raise the blade guard
manually unless the saw is switched off.
• Keep the surrounding area of the machine well maintained and free
of loose materials, e.g. chips and cut-offs.
• Check periodically that the motor air slots are clean and free of
chips.
• Replace the kerf plate when worn.
• Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
• Replace the table insert when worn.
• Never perform any cleaning or maintenance work when the
machine is still running and the head is not in the rest position.
• Replace the table when the slot in the table is too wide.
• When possible, always mount the machine to a bench.
• Report faults in the machine, including guards or saw blades, to
your dealer as soon as they are discovered.
• Ensure that the upper portion of the saw blade is completely
enclosed in the mitre sawing mode.
• If you use a laser to indicate the cutting line, make sure that the
laser is of class 2 according to EN 60825-1:2007. Do not replace
a laser diode with a different type. If damaged, have the laser
repaired by an authorised repair agent.
• Ensure that the arm is securely fixed in the working position in the
bench sawing mode.
• Never use the machine in mitre saw mode as long as the guard is
not fitted (50, fig. D).
• Ensure that the arm is securely fixed when bevelling in the bench
saw mode.
• Never cut workpiece shorter than 150 mm.
• Take care when grooving during the bench saw operation by using
appropriate guarding system. Slotting is not allowed.
• Connect the saw to a dust collection device when sawing wood.
Always consider factors which influence exposure of dust such as:
-– Type of material to be machined (chip board produces more
dust than wood);
-– Correct adjustment of the saw blade;
• Without additional support the machine is designed to accept the
maximum workpiece size of:
– Height 68 mm by width 140 mm by length 600 mm
– Longer workpieces need to be supported by suitable additional
table, e.g. DE3497. Always clamp the workpiece safely.
• Always clamp the workpiece safely.
Additional Safety Rules for Bench Saws
-– Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
• Do not use saw blades with a body thickness greater or a width of
tooth smaller than the thickness of the riving knife.
-– Dust extractor with air velocity not less than 20 m/s
• Make sure that the blade rotates in the correct direction and that
the teeth are pointing to the front of the bench saw.
• Do not use any abrasive discs or diamond cutting wheels..
• In case of an accident or machine failure, immediately turn the
machine off and disconnect machine from the power source.
• Report the failure and mark the machine in suitable form to prevent
other people from using the defective machine.
• When the saw blade is blocked due to abnormal feed force during
cutting, turn the machine off and disconnect it from power supply.
Remove the workpiece and ensure that the saw blade runs free.
Turn the machine on and start new cutting operation with reduced
feed force.
• Never cut light alloy, especially magnesium.
• Whenever the situation allows, mount the machine to a bench
using bolts with a diameter of 8 mm and 80 mm in length (fig. C2).
Additional Safety Rules for Mitre Saws
• Be sure all clamp handles are tight before starting any operation.
• Be sure all blade and flanges are clean and the recessed sides of
the collar are against the blade. Tighten the arbor nut securely.
• Keep the saw blade sharp and properly set.
• Make sure that the riving knife is adjusted to the correct distance
from the blade - maximum 5 mm.
• Never operate the saw without the upper and lower guards in
place.
• Keep your hands out of the path of the saw blade.
• Disconnect the saw from the mains supply before changing blades
or carrying out maintenance.
• Use a push stick at all times, and ensure that you do not place
hands closer than 150 mm from the saw blade while cutting.
• Make sure all locking knobs and clamp handles are tight before
starting any operation.
• Do not attempt to operate on anything but the designated voltage.
• Do not operate the machine without the guard in position, or if the
guard does not function or is not maintained properly.
• Do not reach around behind the saw blade.
• Never use your saw without the kerf plate.
• Do not stand on top of the unit.
• Never place either hand in the blade area when the saw is
connected to the electrical power source.
• During transportation make sure that the upper part of the saw
blade is covered, e.g., by the guard.
• Never attempt to stop a machine in motion rapidly by jamming a
tool or other means against the blade; serious accidents can be
caused unintentionally in this way.
• Do not use the guard for handling or transportation.
• Before using any accessory consult the instruction manual. The
improper use of an accessory can cause damage.
• Do not apply lubricants to the blade when it is running.
• Always keep the push stick in its place when not in use.
• Do not use blades with a body thickness greater or a width of tooth
smaller than the thickness of the riving knife.
• Consider applying specially designed noise-reduction blades.
11
EN GL I S H
Additional Safety Rules for Table Saws
Carrying point
• Rebating, slotting or grooving is not allowed.
• Always use the push stick. Never cut workpiece smaller than
50 mm.
• Without additional support the machine is designed to accept the
maximum workpiece size of:
DATE CODE POSITION (FIG. A1)
The Date Code (39), which also includes the year of manufacture, is
printed into the housing.
Example:
– Height 62 mm by width 600 mm by length 1500 mm
– Longer workpieces need to be supported by suitable additional
table, e.g. DE3497 or DE3472.
Residual Risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
2012 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Partly assembled machine
4 Legs
1 Saw blade
1 Box containing:
– Impairment of hearing.
1 Top guard for bench saw position
– Risk of accidents caused by the uncovered parts of the rotating
saw blade.
1 Under-table guard for mitre saw position
– Risk of injury when changing the blade.
1 Push stick
1 Parallel fence
1 Material clamp
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
1 Plastic bag containing:
4 M8 locking knobs
The following factors are of influence to noise production:
4 M8 x 50 mushroom head bolts
– The material to be cut.
4 D8 flat washers
– The type of saw blade.
– The feed force.
The following factors increase the risk of breathing problems:
– No dust extractor connected when sawing wood.
– Insufficient dust extraction caused by uncleaned exhaust filters
– Worn saw blade.
– Workpiece not exactly guided.
Markings on Tool
The following pictograms are shown on the tool:
1 Locking grommet
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
• Remove the saw from the packaging material carefully.
Description (fig. A1–A8)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Read instruction manual before use.
A1
Wear ear protection.
1 On/off switch (bench saw mode)
2 Table release lever
3 Rotating table clamp
Wear eye protection.
4 Mitre saw table
5 Rotating table
6 Fence right-hand side
Never use the mitre saw when the guard is not in place.
7 Fence left-hand side
8 Rotating table location plunger
✔
9 Mitre scale/table insert
10 Dust extraction adapter
11 Fixed upper blade guard
When using the machine in the mitre saw mode, make sure
to operate the trigger switch when switching on and off. Do
not operate the switchbox in this mode.
12 Moveable lower blade guard
13 Guard release lever
14 Operating handle
A2
When using the machine in the bench saw mode, make
sure that the riving knife has been mounted. Do not use the
machine without the riving knife.
14 Operating handle
15 Trigger switch (mitre saw mode)
16 Riving knife storage
17 Push stick storage
Do not use the riving knife when using the machine in the
mitre saw mode. Make sure that the riving knife is secured in
the upper rest position (fig. A2).
18 Leg
19 Foot
20 Table locking device
21 Saw table retention bracket
12
ENGLI SH
22 Bevel clamp handle
Electrical Safety
BENCH SAW MODE
The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
A3
22 Bevel clamp handle
23 Height adjuster
24 Bench saw table
25 Upper blade guard
26 Parallel fence
This machine is of Class I construction; therefore earthed (grounded)
connection is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
27 Mitre fence (option)
If the supply cord is damaged, it must be replaced by a specially
prepared cord available through the DEWALT service organisation.
OPTIONAL ACCESSORIES
Mains Plug Replacement
(U.K. & Ireland Only)
For use in mitre saw mode:
If a new mains plug needs to be fitted:
A4
• Safely dispose of the old plug.
28 Adjustable stand 760 mm (max. height) (DE3474)
• Connect the brown lead to the live terminal in the plug.
29 Support guide rails 1,000 mm (DE3494)
• Connect the blue lead to the neutral terminal.
29 Support guide rails 500 mm (DE3491)
• Connect yellow/green lead to the earth terminal
30 Swivelling stop (DE3462)
31 Length stop for short workpieces (to be used with guide rails [29])
(DE3460)
32 Support with removable stop (DE3495)
33 Support with stop removed (DE3495)
34 Material clamp (DE3461)
A5
35 Roller support table (DE3497)
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug should be fitted by a competent person. If you are in
doubt, contact an authorized DEWALT repair agent or qualified
electrician.
• The plug fitted should comply with BS EN60309 (BS4343),
16 Amps, earthing contact position 4h.
For use in bench saw mode:
Using an Extension Cable
A3
If an extension cable is required, use an approved 3–core extension
cable suitable for the power input of this tool (see Technical Data).The
minimum conductor size is 1.5 mm2; the maximum length is 30 m.
27 Mitre fence (DE3496)
A6
When using a cable reel, always unwind the cable completely.
36 Extension table (DE3472)
ASSEMBLY AND ADJUSTMENTS
A7
37 Single sliding table (DE3471)
Not shown
– Double sliding table
For use in all modes:
A8
38 Three way dust extraction kit (DE3500)
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental startup can cause injury.
Unpacking
WARNING: When moving the machine, always seek
assistance. The machine is too heavy for one person to
handle.
INTENDED USE
• Remove the loose packaging material from the box.
Your DEWALT flip-over saw has been designed to operate as a mitre
saw or saw bench to perform the four main sawing operations of
ripping, cross-cutting, bevelling and mitring easily, accurately and safely.
• Lift the machine out of the box.
This unit is designed for use with a nominal blade diameter 250 mm
carbide tip blade for professional cutting wood, wood products and
plastics.
MITRE SAW MODE
In mitre saw mode, the sawing machine is used in vertical, mitre or
bevel position.
BENCH SAW MODE
Turned over on its central axis, the sawing machine is used to perform
the standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.
WARNING: Do not use the machine for other purposes as
described.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack
of experience, knowledge or skills unless they are supervised by
a person responsible for their safety. Children should never be left
alone with this product.
• Remove the parts box from the interior of the machine.
• Remove any remaining packing material from the machine.
Mounting the Legs (fig. C1)
With the legs mounted, the machine is suitable for stand-alone
placement.
• Turn the machine upside down.
• Pass a coach bolt (47) from the flat side through the holes into
each of the legs (18).
• Place a lock knob (48) and washer (49) onto the bolts.
• Present a leg (18) to each of the mounting points (46) located at
the edges on the inside of the base. For each leg, make sure that
the lock knob and washer locate at the outside of the open ended
slot.
• Tighten the lock knobs.
13
EN GL I S H
• Turn the machine straight up. Make sure it is level; adjust the leg
clamping height if required.
Mounting the Machine to the Workbench (fig. C2)
With the legs removed, the machine is suitable for placement on a
workbench. To ensure a safe operation, the machine has to be fixed to
the workbench and mounted with bolts 8 mm diameter by 80 mm long.
ASSEMBLY FOR MITRE SAW MODE
Mounting the Under-table Guard (fig. D)
The under-table guard (50) is fitted to the top of the bench saw table.
• Place the two hooks on the left of the guard into the oblong slots
on the left of the blade slot (52).
• Place the guard flat on the table and press it in the locking
grommet.
• To remove, loosen the grommet with a screwdriver and proceed in
reverse order.
Turning the Sawhead and Table Over
(fig. A3, E1, E2)
• Withhold the saw table with one hand and push the table release
lever (2) to the left (fig. E1).
• Push the table downwards at the front and swing it over completely
until the motor assembly is uppermost and the indentation engages
in the retaining teeth of the table locking device (20).
• The head assembly is held down by a clamp strap at the front and
a height adjuster (23) at the rear (fig. A3).
• Remove the strap.
• Rotate the wheel (55) counterclockwise whilst holding down the
head until the "U"-shaped bracket (56) can be disengaged from its
seating (fig. E2).
• Replace the outer arbor collar.
• Tighten the blade locking screw (60) by turning counterclockwise
while holding the hex key steady with your other hand.
• Place the blade spanner and Hex key in their storage position.
WARNING: After mounting or replacing the blade, always
check that the blade is fully covered by the guard. Make
sure the blade spanner and hex key have been replaced in
their storage position.
Adjustments for Mitre Saw Mode
WARNING: Be aware the saw blade shall be replaced in
the described way only. Only use saw blades as specified
under Technical Data; Cat.no.: DT4321.
Your mitre saw was accurately adjusted at the factory. If readjustment
due to shipping and handling or any other reason is required, follow the
steps below to adjust your saw. Once made, these adjustments should
remain accurate.
Checking and Adjusting the Blade to the Fence
(fig. G1, G2, H)
With the head in the vertical position and the bevel clamp handle (22)
released, slacken the locking screw (65) in the rotating table location
plunger (8) (fig. G1).
• Pull down the head until the blade just enters the saw kerf.
• Place a square (66) against the left side (7) of the fence and blade
(62) (fig. G2). The angle should be 90°.
WARNING: Do not touch the tips of the blade teeth with
the square.
• If adjustment is required, proceed as follows:
• Rotate the eccentric adjustment bush (67) until the face of the saw
blade is flat against the square (fig. G1).
• Swing and push the height adjuster up.
• Tighten the locking screw (65).
• Holding the head firmly, allow the spring pressure to take the head
upwards into its rest position.
• Check that the red marks (68) near the blade slot (52) are in line
with the 0° position (69) on the two scales (fig. H).
Mounting the Saw Blade (fig. A1, A2, F1–F3)
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental startup can cause injury.
Checking and Adjusting the Blade to the Table
(fig. I1, I2)
• Loosen the bevel clamp knob (22) (fig. I1).
WARNING: Be aware the saw blade shall be replaced in
the described way only. Only use saw blades as specified
under Technical Data; Cat.no.: DT4321.
• Press the saw head to the right to ensure it is fully vertical and
tighten the bevel clamp handle.
WARNING: The teeth of a new blade are very sharp and
can be dangerous.
• Place a set square (66) on the table and up against the blade (62)
(fig. I2). The angle should be 90°.
WARNING: Always change blades with the machine in
mitre saw mode.
• Ensure riving knife (16) is secured in the upper rest position (fig. A2).
• Insert the hex key (57) through the hole (58) in the belt casing into
the spindle end (fig. F1). Place the blade spanner (59) onto the
blade locking screw (60) (fig. F2).
• The blade locking screw has a left-handed thread, therefore holding
the hex key firmly, turn the spanner clockwise to loosen.
• Depress the head lock up guard release lever (13) to release the
lower guard (12), then raise the lower guard as far as possible.
• Remove the blade locking screw (60) and the outside arbor collar
(61) (fig. F3).
• Make sure the inner flange and both faces of the blade are clean
and free of dust.
• Install the saw blade (62) onto the shoulder (63) provided on the
inside arbor collar (64), making sure that the teeth at the bottom
edge of the blade are pointing toward the back of the saw (away
from the operator).
• Carefully ease the blade into position and release the lower blade
guard.
14
• If adjustment is required, loosen the screws (70) and bring the
indicators in line. The 45° position should now also be accurate. If
this is not the case, the blade is not perpendicular to the rotating
table (see below).
• Pull down the head until the blade just enters the saw kerf.
WARNING: Do not touch the tips of the blade teeth with
the square.
• If adjustment is required, proceed as follows:
• Loosen the bevel clamp knob (22) (fig. I1) and turn the vertical
position adjustment stop screw (71) in or out until the blade is at
90° to the table as measured with the square (66) (fig. I2).
Checking and Adjusting the Mitre Angle
(fig. A1, A2, H)
The straight cross-cut and 45° mitre positions are pre-set.
• Pull up the rotating table location plunger (8) and rotate it
counterclockwise a quarter of a turn (fig. A1).
• Loosen the rotating table clamp (3). The handle allows a ratchettype action when full rotation of the handle is not possible.
• Grip the control handle (14) (fig. A2), compress the guard release
lever (13) and lower the saw about halfway (fig. A1).
• Turn the sawhead with its rotating table to the required position.
• Tighten the rotating table clamp (3). The rotating table location
plunger (8) will engage automatically (fig. A1).
ENGLI SH
• Using the red marks (68), the mitre saw table (4) can be set to any
mitre angle left or right between 0° and 45° (fig. H).
• Proceed as for pre-set positions. The rotating table location plunger
cannot be used for intermediate angles.
WARNING: Always make a trial cut in a piece of waste
wood, to check for accuracy.
Adjusting the Fence (fig. J1, J2)
The moveable part of the left side of the fence can be adjusted to
provide maximum support of the workpiece near the blade, while
allowing the saw to bevel to a full 45° left. The sliding distance is limited
by stops in both directions. To adjust the fence (7):
• Lift the lever (72) to release the fence (7).
• Slide the fence to the left.
• Make a dry run with the saw switched off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and
down movement of the arm.
• Push the lever (72) down to secure the fence in place.
Fitting the Upper Blade Guard (fig. N)
The upper blade guard (25) is designed to be quickly and easily
attached, via a spring-loaded plunger to the hole in the riving knife
(16) once it has been positioned through the worktable for bench saw
mode.
Secure the upper blade guard (25) to the riving knife by pulling the knob
(76) to allow the plunger in the guard to engage.
WARNING: Never use your saw in bench saw mode
without the upper guard correctly fitted.
Mounting and Adjusting the Parallel Fence (fig. O)
The dual height parallel fence (26) can be used in two positions (11 or
62 mm). The parallel fence can be mounted on either side of the blade.
TO MOUNT THE FENCE INTO THE APPROPRIATE POSITION,
PROCEED AS FOLLOWS:
• Loosen the knob (77).
• Slide the bracket on from the left or the right. The clamping plate
(78) engages behind the front edge of the table.
• Tighten the knob (77).
Checking and Adjusting the Bevel Angle
(fig. J1, K1, K2)
• Slide the side fence to the left as far as it will go (fig. J1).
• Loosen the bevel clamp handle (22) and move the saw head to the
left. This is the 45° bevel position.
• If adjustment is required, proceed as follows:
• Turn the stopscrew (73) in or out as necessary until the pointer (74)
indicates 45°.
ASSEMBLY FOR BENCH SAW MODE
Changing from Mitre Saw to Bench saw Mode
(fig. A1–A3, E2, L1, L2)
• Put the blade into 0° cross-cut position with the rotating table
location plunger (8) correctly located and the rotating table clamp
(3) secured (fig. A1).
• Slacken the riving knife clamp bolt (75) just enough to allow the
riving knife to enter the mounting slot (fig. L1).
• Take the riving knife (16) from its storage position against the saw
head (fig. A2).
• Depress the guard release lever (13) to release the blade guard
(12), then raise the blade guard as far as possible (fig. A1).
• Slide the riving knife bracket (76) fully into the mounting slot (77)
(fig. L1). Tighten the clamp bolt.
• Gently release the lower guard until it is held in place behind the
edge protruding from the inside of the riving knife.
• Check that the fence is parallel to the blade.
• If adjustment is required, proceed as follows:
• Adjust the fence so that it is parallel to the blade by checking the
distance between the blade and the fence at the front and rear of
the blade. To do so, turn the adjustment screw in the fence support
in or out as necessary.
The default set-up of the fence is to the right-hand side of the blade.
TO PREPARE THE FENCE FOR USE TO THE LEFT-HAND SIDE OF THE BLADE,
PROCEED AS FOLLOWS:
• Loosen the knob (77).
• Pull out the bracket (79) and replace it in the other end.
• Fit the fence to the table.
• Tighten the knob (77).
WARNING: Use the 11 mm profile for ripping low
workpieces to allow access between the blade and the
fence for the push stick (17).
WARNING: The rear end of the fence should be level with
the front of the riving knife.
Changing from Bench saw to Mitre Saw Mode
(fig. A3, D, E1, E2, L1)
• Remove the parallel fence (26) (fig. A3).
• Turn the wheel (55) of the height adjuster (23) to provide maximum
cutting depth in mitre saw mode (fig. E2).
• Remove the under-table guard.
• Proceed as described in the section Turning the sawhead and
table over.
• Pull down the saw head and swing the height adjuster (23) until its
U-shaped bracket (56) engages on the pin provided in the base
(fig. E2).
• Slacken the riving knife clamp bolt (75) and remove the riving knife
(16), while holding the blade guard (12) (fig. L1).
• Turn the wheel (55) of the adjuster to make the blade and riving
knife protrude from the bench saw table (24) (fig. A3) to provide
maximum cutting depth in bench saw mode.
WARNING: The blade should not foul the lower blade
guard.
• Pull the table release lever (2) to the left, lift the front edge of the
table and flip it back through 180° until the teeth of the tablelocking device (20) automatically engage the saw blade retention
lever to secure it in the bench saw mode (fig. L2).
WARNING: Be careful not to lose control over the
movement of the table.
• Lower the blade guard.
• Place the riving knife in its storage position against the saw head.
• Replace the under-table guard (50) (fig. D).
Prior to Operation
• Install the appropriate saw blade. Do not use excessively worn
blades. The maximum rotation speed of the tool must not exceed
that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
Position of the Riving Knife (fig. M)
• Fit the riving knife (16) as described above. Once fitted, the riving
knife does not require further adjustment.
15
EN GL I S H
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
CAUTION: Always use a workpiece clamp to maintain
control and reduce the risk of personal injury and workpiece
damage.
Use the workpiece clamp (34) provided with your saw. Other aids such
as spring clamps, bar clamps or C-clamps may be appropriate for
certain sizes and shapes of material. The left side fence will slide from
side to side to aid in securing.
TO INSTALL CLAMP
1. Insert the workpiece clamp into the hole lateral to the mitre fence.
WARNING:
2. Rotate the clamp arm toward to the front of the mitre saw.
• The attention of UK users is drawn to the "woodworking
machines regulations 1974" and any subsequent
amendments.
3. Loosen the knob to adjust the clamp up and down and secure it in
the choosen height.
• Ensure the material to be sawn is firmly secured in place.
• Apply only a gentle pressure to the tool and do not exert
side pressure on the saw blade.
• Avoid overloading.
Ensure the machine is placed to satisfy your ergonomic conditions in
terms of table height and stability. The machine site shall be chosen so
that the operator has a good overview and enough free surrounding
space around the machine that allows handling of the workpiece
without any restrictions.
To reduce effects of vibration make sure the environment temperature
is not too cold, machine and accessory is well maintained and the
workpiece size is suitable for this machine.
Switching on and off (fig. A1–A2, P)
This machine has two independent switching systems. In bench saw
mode, the on/off switch (1) (fig. A1) is used. In mitre saw mode, the
trigger switch (15) (fig. A2) is used.
BENCH SAW MODE (FIG. P)
The on/off switch used in bench saw mode offers multiple advantages:
– no-volt release function: should the power be shut off for some
reason, the switch has to be deliberately reactivated.
– extra safety: the hinged safety enclosure plate can be locked by
passing a padlock through the centre hasp. The plate also serves
as an "easy to locate" emergency stop button as pressure on the
front of the plate will depress the stop button.
To switch the machine on, press the green start button (80).
4. Use the fine adjust knob to firmly clamp the workpiece.
NOTE: Place the clamp on the right side of the base when beveling.
ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS TO
CHECK THE PATH OF THE BLADE. ENSURE THE CLAMP DOES NOT
INTERFERE WITH THE ACTION OF THE SAW OR GUARDS.
General Handling
– In the mitre saw mode, the sawhead is automatically locked in the
upper "park" position.
– Squeezing the guard release lever will unlock the sawhead. Moving
the sawhead down retracts the moveable lower guard.
– Never seek to prevent the lower guard returning to its park position
when the cut is completed.
– The minimum length of offcut material is 10 mm.
– When cutting UPVC sections, a supporting piece made out of
timber with a complementary profile should be placed beneath the
material being cut to provide the correct level of support.
Vertical Straight Cross Cut (fig. Q)
• Set the rotating table to 0° and make sure that the locating plunger
is engaged.
• Tighten the rotating table clamping knob.
• Place the wood to be cut against the fence. Take hold of the
control handle and press in the guard retraction lever.
• Switch the machine on.
• Allow the blade to cut freely. Do not force.
MITRE SAW MODE (FIG. A2)
• After completing the cut, release the switch and wait for the saw
blade to come to a complete standstill before returning the head to
its upper rest position.
To switch the machine on, press the trigger switch (15).
• Release the guard retraction lever.
To switch the machine off, press the red stop button (81).
To switch the machine off, release the trigger switch.
WARNING: Do not allow the sawhead to jump back
unaided to prevent damage.
BASIC SAW CUTS
Sawing in Mitre Saw Mode
It is dangerous to operate without guarding. Guards must be in position
when sawing.
• Make sure that the under-table guard does not become clogged
with sawdust.
Clamping the Workpiece (fig. Q, R, S, X)
WARNING: A workpiece that is clamped, balanced
and secure before a cut may become unbalanced after
a cut is completed. An unbalanced load may tip the
saw or anything the saw is attached to, such as a table
or workbench. When making a cut that may become
unbalanced, properly support the workpiece and ensure the
saw is firmly bolted to a stable surface. Personal injury may
occur.
WARNING: The clamp foot must remain clamped above
the base of the saw whenever the clamp is used. Always
clamp the workpiece to the base of the saw – not to any
other part of the work area. Ensure the clamp foot is not
clamped on the edge of the base of the saw.
16
Mitre Cuts (fig. R)
• Set the required mitre angle.
• Ensure that the rotating table clamp is tightly secured.
• Proceed as for a vertical straight cross-cut.
• Prevent the blade cutting the table if the angle is not 45°.
WARNING: When mitring the end of a piece of wood with
a small off-cut, position the wood to ensure that the offcut is to the side of the blade with the greater angle to the
fence: left mitre, off-cut to the right mitre, off-cut to the left.
Bevel Cuts (fig. A2, S)
• Release the bevel clamp handle (22) and tilt the head to the angle
required.
• Tighten the bevel clamp handle.
• Proceed as for a vertical straight cross-cut.
Compound Mitre
This cut is a combination of a mitre and a bevel cut. The limitations are
35° mitre/30° bevel. Do not exceed these limits.
Set the bevel angle and subsequently set the mitre angle.
ENGLI SH
Sawing in the Bench Mode
• Always use the riving knife.
• Always ensure that the riving knife and blade guard are correctly
aligned.
• Always ensure that the mitre saw is set and locked in 0° mitre.
WARNING: DO NOT cut any type of metal material.
Ripping (fig. A2, T)
• Set the bevel angle to 0°.
• Adjust the saw blade height. The correct blade position is to have
the tips of three teeth above the top surface of the wood.
• Set the parallel fence to the required distance.
• Hold the workpiece flat on the table and against the fence. Keep
the workpiece approx. 25 mm away from the saw blade.
• Keep both hands away from the path of the saw blade.
• To prevent small offcut pieces fouling against the blade,
prepare a tapered length of timber and clamp it on the rear
edge of the worktable close enough to the right-hand side of
the blade so that successive offcuts feed automatically to the
right.
– For ripping narrow (< 120 mm) and long workpieces:
• Place the fence in rearmost position to maintain accuracy
during long cuts.
• Push the workpiece with both hands (one on each side of
the blade).
• Use a push stick when close to the blade.
• Support long workpieces at the outfeed side.
– For ripping wider (> 120 mm) workpieces:
• Adjust the fence forward as in figure W if the material being
cut tends to jam between the blade or the riving knife and
the fence.
Optional Attachments
• Switch the machine on and allow the saw blade to reach full
speed.
WARNING: Prior to assembling any accessories always
unplug the machine.
• Slowly feed the workpiece underneath the upper blade guard,
keeping it firmly pressed against the fence. Allow the teeth to cut,
and do not force the workpiece through the saw blade. The saw
blade speed should be kept constant.
WARNING: Since accessories, other than those offered
by DEWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT, recommended
accessories should be used with this product.
• Remember to use the push stick (17) when close to the blade.
• After completing the cut, switch the machine off, allow the saw
blade to stop and remove the workpiece.
WARNING: Never push or hold the free or cut-off side of
the workpiece.
WARNING: Always use a push stick when ripping small
workpieces.
Bevel Cuts (fig. U)
• Release the bevel clamp handle and set the blade to the required
angle.
DUST EXTRACTION KIT (FIG. A1, A2, A8)
This machine is provided with three dust extraction points for use in
mitre mode and two in bench mode.
• When sawing wood, always connect a dust extraction device
designed in accordance with the relevant regulations regarding dust
emission.
WARNING: Whenever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
• In order to prevent material jamming between the blade and the
fence, position the fence to the left of the blade.
Connect a dust collection device designed in accordance with the
relevent regulations. The air velocity of externally connected systems
shall be 20 m/s +/- 2 m/s. Velocity to be measured in connection tube
at the point of connection, with the tool connected but not running.
• Proceed as for vertical ripping.
A seperate dust kit is available as an option (DE3500)
Mitre Cuts (fig. V1–V3)
• To adjust the mitre fence, loosen the stop screw locknut (81) and
screw the stop (82) in or out until the mitre pointer reads 0°
(fig. V1).
1. Fit the dust extraction tube to the nozzles; the longer hose to upper
nozzle.
2. Connect the hoses to the three way connector.
Connecting - mitre saw position
• Set the blade height and angle.
• Connect one hose to the under-table guard.
• Insert the slide bar (83) of the mitre fence into the groove (84)
provided in the left-hand side of the table (fig. V2).
• Connect one hose to the small diameter outlet and one to the
large diameter outlet using the corresponding spouts.
• Loosen the mitre locking knob (85) and rotate the fence to set the
scale to the required angle (fig. V3).
• Connect the hoses to the 3-way connector.
• Tighten the mitre locking knob (85).
• Place the workpiece against the flat surface of the mitre fence.
Switch on and, holding the workpiece firmly, slide the fence along
the groove to take the workpiece into the blade. When the cut is
completed, switch off immediately.
Fence Positions, Bench Saw Mode (fig. W)
– For ripping thin materials, use the 11 mm profile of the dual height
parallel fence and position the fence opposite the front edge of the
riving knife.
– For ripping thicker materials, use the 62 mm profile of the dual
height parallel fence.
– For cross-cutting narrow and short workpieces (fig. W):
• Adjust the parallel fence with the low profile facing the blade
and install the rear of the fence in line with the leading edge
of the blade.
• Set the workpiece against the mitre fence (at 0° or 90°) and
push the mitre fence to make the cut.
• Connect the single outlet of the 3-way connector to the hose from
the dust extractor.
Connecting - bench saw position
• Connect one hose to the small diameter outlet and one to the large
diameter using the corresponding spouts.
• Blank off the middle opening of the 3-way connector.
• Connect both hoses to the outer outlets.
MITRE SAW EXTRA SUPPORT/LENGTH STOP (FIG. A4)
The extra support and length stop can be mounted on the left-hand
side or on the right-hand side, or with two sets on either side.
• Fit the items 28–34 onto the two guide rails (29).
• Use the swivelling stop (30) for cross-cutting 210 mm wide boards
(15 mm thick).
ROLLER SUPPORT TABLE (FIG. A5)
In mitre saw mode, the roller support table can be mounted on the lefthand side or on the right-hand side, or with two sets on either side.
In bench saw mode, it can also be mounted in front or at the rear of the
saw table.
17
EN GL I S H
SIDE EXTENSION TABLE (FIG. A6)
The side extension table increases the distance from the rip fence to
the blade to 600 mm or more, depending on the rod length fitted to the
machine and the clamped position of the table. The side extension table
must be used in conjunction with guide rails (29) (option).
The adjustable table is equipped with an engraved scale along its front
edge and mounted on a sturdy base which clamps to the guide rods.
• Fit the extension table to the right-hand side of the machine for
continuity of the distance scale on both tables.
SINGLE SLIDING TABLE (FIG. A7)
This sliding table (37) allows for board sizes to the left of the blade up to
1200 x 900 mm.
The guide rods are mounted on a sturdy alloy extrusion which is quickly
detachable from the machine and yet fully adjustable is all planes.
The fence incorporates a full length measuring tape for quick positioning
of an adjustable stop and an adjustable support for narrow workpieces.
DOUBLE SLIDING TABLE
This sliding table allows for board sizes to the left of the blade up to
1850 mm.
Transporting
WARNING: Always transport the machine in bench saw
mode with the upper blade guard fitted.
• Remove the legs.
WARNING: When carrying the machine, always use the
hand indentations (fig.A1;40) and seek for assistance. The
machine could be too wide protruding for one person to
handle.
MAINTENANCE
Your DEWALT power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental startup can cause injury.
Lubrication
The bearings of the motor are pre-lubricated and watertight.
• Slightly oil the rotating table bearing surface where it slides on the
lip of the fixed table at regular intervals.
• Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
18
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade. Remove the
jammed parts and reassembling the saw blade.
Optional Accessories
WARNING: Since accessories, other than those offered
by DEWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT, recommended
accessories should be used with this product.
SAW BLADES
ALWAYS USE noise reduced 250 mm SAW BLADES WITH 30 mm
ARBOR HOLES. SPEED RATING MUST BE AT LEAST 3000 RPM.
Never use a smaller or greater diameter blade. It will not be guarded
properly. Use cross cut blades only. Do not use blades designed for
fast ripping, combination blades or blades with hook angles in excess
of 10°.
BLADE DESCRIPTIONS
APPLICATION
DIAMETER
TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
250 mm
30 (Series 60)
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
250 mm
60 (Series 60)
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
Separate collection. This product must not be disposed of
with normal household waste.
Should you find one day that your DEWALT product needs replacement,
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
DEWALT provides a facility for the collection and recycling of DEWALT
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT repair agents and
full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
ENGLI SH
GUARANTEE
DEWALT is confident of the quality of its products and offers
an outstanding guarantee for professional users of the
product. This guarantee statement is in addition to and in no
way prejudices your contractual rights as a professional user
or your statutory rights as a private non-professional user. The
guarantee is valid within the territories of the Member States of
the European Union and the European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of
your DEWALT tool, simply return it within 30 days, complete
with all original components, as purchased, to the point of
purchase, for a full refund or exchange. The product must
have been subject to fair wear and tear and proof of purchase
must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your DEWALT tool, in
the 12 months following purchase, you are entitled to one
service free of charge. It will be undertaken free of charge at
an authorised DEWALT repair agent. Proof of purchase must
be produced. Includes labour. Excludes accessories and
spare parts unless failed under warranty.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, DEWALT guarantees to replace all defective parts
free of charge or – at our discretion – replace the unit free of
charge provided that:
• The product has not been misused;
• The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorised
persons;
• Proof of purchase is produced;
• The product is returned complete with all original
components.
If you wish to make a claim, contact your seller or check the
location of your nearest authorised DEWALT repair agent in
the DEWALT catalogue or contact your DEWALT office at the
address indicated in this manual. A list of authorised DEWALT
repair agents and full details of our after-sales service is
available on the Internet at: www.2helpU.com.
19
20
21
Belgique et
Luxembourg
België en
Luxemburg
Danmark
Deutschland
Ελλάς
España
France
Schweiz
Suisse
Svizzera
Ireland
Italia
Nederlands
Norge
Österreich
Portugal
Suomi
Sverige
Türkiye
United
Kingdom
Middle East
Africa
N163067
Black & Decker - DEWALT
Nieuwlandlaan 7, IZ Aarschot B156
B-3200 Aarschot
Dutch Tel: 32 70 220 063
French Tel: 32 70 220 062
DEWALT
Sluseholmen 2-4
2450 København SV
DEWALT
Richard Klinger Str. 11
65510 Idstein
Black & Decker (Ελλάς) Α.Ε.
Τηλ:
Στράβωνος 7 & Βουλιαγμένης 159
Service:
Γλυφάδα 16674, Αθήνα
Φαξ:
DEWALT
Parque de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
DEWALT
5, allée des hêtres
BP 30084, 69579 Limonest Cedex
DEWALT
In der Luberzen 40
8902 Urdorf
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
DEWALT
c/o Energypark Building 03 sud, Via Monza 7/A,
20871 Vimercate (MB), IT
Black & Decker - DEWALT
Joulehof 12
4600 AB Bergen Op Zoom
DEWALT
Postboks 4613, Nydalen
0405 Oslo
DEWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248
A-1230 Wien
DEWALT
Centro de Escritórios de Sintra Avenida Almirante
Gago Coutinho, 132/134, Edifício 142710-418 Sintra
2710-418 Lisboa
DEWALT
Tekniikantie 12
02150 Espoo, Finland
DEWALT
Box 94
431 22 Mölndal
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
DEWALT
Tel:
210 Bath Road; Slough, Berks SL1 3YD Fax:
DEWALT
P.O. Box - 17164,
Jebel Ali (South Zone), Dubai, UAE
30 210 8981-616
30 210 8981-616
30 210 8983-570
Fax: 32 70 225 585
Fax: 32 70 222 441
www.dewalt.be
Tlf:
70201511
Fax: 70224910
www.dewalt.dk
Tel:
06126-21-1
Fax: 06126-21-2770
www.dewalt.de
www.dewalt.gr
Tel:
934 797 400
Fax: 934 797 419
www.dewalt.es
Tel:
04 72 20 39 20
Fax: 04 72 20 39 00
www.dewalt.fr
Tel:
01 - 730 67 47
Fax: 01 - 730 70 67
www.dewalt.ch
Tel:
00353-2781800
Fax: 00353-2781811
www.dewalt.ie
Tel:
800-014353
Fax: 39 039 9590 317
www.dewalt.it
Tel:
31 164 283 063
Fax: 31 164 283 200
www.dewalt.nl
Tel:
45 25 13 00
Fax: 45 25 08 00
www.dewalt.no
Tel:
01 - 66116 - 0
Fax: 01 - 66116 - 14
www.dewalt.at
Tel:
214 66 75 00
Fax: 214 66 75 75
www.dewalt.pt
01753-56 70 55
01753-57 21 12
Puh: 010 400 430
Faksi: 0800 411 340
www.dewalt.fi
Tel:
031 68 61 00
Fax: 031 68 60 08
www.dewalt.se
Tel:
0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
www.dewalt.co.uk
Tel:
971 4 8863030
Fax: 971 4 8863333
www.dewalt.ae
03/12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising