Operating instructions KENWOOD KRF-V5020

Operating instructions KENWOOD KRF-V5020
You can read the recommendations in the user guide, the technical guide or the installation guide for KENWOOD KRF-V5020.
You'll find the answers to all your questions on the KENWOOD KRF-V5020 in the user manual (information, specifications, safety
advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide.
User manual KENWOOD KRF-V5020
User guide KENWOOD KRF-V5020
Operating instructions KENWOOD KRF-V5020
Instructions for use KENWOOD KRF-V5020
Instruction manual KENWOOD KRF-V5020
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
Manual abstract:
@@@@In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote
control and how to switch its operation modes (etc.). Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations. B60-4155-00 02 MA (T,E2,Q) OC 9809 Remote Control Other Operations Preparation Getting started 2 Before
applying the power Units are designed for operation as follows. U.K. and Europe ....
.....
.....
..........
..........
.....
.....
... AC 230 V only Russia .......
..........
.....
.....
..........
..........
.....
.....
...... AC 220 V only Caution : Read this page carefully to ensure safe operation. KRF-V7020/V6020/V5020 (En/T) Unpacking Unpack the unit carefully and
make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. @@@@@@@@Keep this
manual handy for future reference.
For the United Kingdom Preparations Operations Other Factory fitted moulded mains plug 1. The mains plug contains a fuse. For replacement, use only a
13Amp ASTA-approved (BS1362) fuse. 2. The fuse cover must be refitted when replacing the fuse in the moulded plug. 3. Do not cut off the mains plug from
this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate
safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug
immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. Accessories FM indoor antenna (1) IMPORTANT The wires in
the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live Do not connect those leads to the earth terminal of a threepin plug.
AM loop antenna (1) Loop antenna stand (1) REQUIREMENT BY NEDERLAND GAZETTE Batteries are supplied with this product. When they empty, you
should not throw away. Instead, hand them in as small chemical waste. For KRF-V7020, KRF-V6020 Batteries (R03/AAA) (4) Remote control unit (1) RCR0508 Safety precautions WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. For
KRF-V5020 Remote control unit (1) RC-R0710 Batteries (R06/AA) (2) Cleaning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not use volatile
solvents such as alcohol, paint thinner, gasoline, or benzine, etc.
to clean the cabinet. Use a clean dry cloth. Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners
containing oil, for they may deform the plastic components. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK).
NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE LIGHTNING FLASH WITH ARROWHEAD
SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS
VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK
TO PERSONS. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF
IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. Getting
started KRF-V7020/V6020/V5020 (En/T) Contents Caution : Read the pages marked safe operation. carefully to ensure 3 Getting started ......
..........
.....
.....
......... 2 Before applying the power .
..........
.....
.....
..........
... 2 Safety precautions .......
.....
.....
..........
..........
.....
.....
2 Unpacking ..........
..........
.....
.....
..........
..........
.....
.....
2 How to use this manual ..........
..........
.....
.....
..........
4 Special features ..........
.....
.....
..........
..........
.....
.....
. 4 Names and functions of parts .........
........ 5 Setting up the system ..
.....
.....
..........
..... 8 Preparations Connecting audio components .....
.....
.....
..........
.. 8 Connecting video components ........
.....
.....
..........
9 Connecting DVD 6-channel jack ..........
.....
.....
..... 9 Connecting the antennas .....
..........
.....
.....
..........
.. 9 Connecting the system control ........
.....
.....
........ 10 Connecting the speakers ..
..........
.....
.....
..........
... 11 Preparing the remote control (RC-R0508) .......
.. 12 Preparing the remote control (RC-R0710) ...
.....
. 13 Preparing for surround sound .........
....... 13 Speaker settings ...
.....
.....
..........
..........
.....
.....
..... 13 Normal playback .....
..........
.....
.....
....... 14 Operations Remote Control Other Preparing for playback ...
..........
.....
.....
..........
..... 14 Listening to a source component .....
.....
.....
....... 15 Adjusting the sound ...
..........
.....
.....
..........
..........
15 Recording .....
.....
..........
..........
.....
.....
16 Recording audio ..........
..........
.....
.....
..........
......... 16 Recording video .
.....
.....
..........
..........
.....
.....
........ 16 Listening to radio broadcasts ..
..........
.....
17 Tuning (non-RDS) radio stations .....
..........
........ 17 Using RDS (Radio Data System) ..
.....
.....
..........
. 17 Using the DISPLAY key .........
.....
.....
..........
......... 18 Presetting RDS stations (RDS AUTO MEMORY) .
.....
.....
..........
..........
.....
.. 18 Presetting radio stations manually ...
..........
........ 19 Receiving preset stations ..
.....
.....
..........
..........
.. 19 Receiving preset stations in order (P.CALL) ..
... 19 Tuning by program type (PTY search) ..
..........
.. 20 Reserving the desired information ........
.....
.....
... 20 Operations Ambience effects .......
..........
.....
.....
.... 22 Surround modes ......
..........
.....
.....
..........
..........
... 22 Surround play ..
.....
..........
..........
.....
.....
..........
...... 23 DVD 6-channel playback ....
.....
.....
..........
..........
. 23 Convenient functions ....
.....
..........
..........
.....
.....
.. 24 Other In case of difficulty ........
..........
.....
.....
. 25 Specifications .........
..........
.....
.....
...... 27 Quick start guide ....
..........
.....
.....
......... 1 Getting the most from your remote control .
..........
.....
.....
........ 3 Setup code chart ..
..........
.....
.....
..........
. 7 In case of difficulty .........
.....
.....
..........
13 Remote operation of other components .... 14 Remote Control (Separate booklet) (RC-R0508) Preparations Getting started How to use this manual Special
features True home theater sound KRF-V7020/V6020/V5020 (En/T) 4 The manual covers the KRF-V7020, KRF-V6020, and KRF-V5020. Items such as
functions, number of jacks, and remote control details differ somewhat between these models. To confirm the functions available on the model you have
purchased, refer to the table below. Model name KRF-V7020 Remote Control Terminal Preout This receiver incorporates a wide variety of surround modes to
bring you maximum enjoyment from your video software. Select a surround mode according to your equipment or the software you are going to play and
enjoy! TM Speaker out Front input Dolby Pro Logic & Dolby 3 Stereo This surround system reproduces theater-like surround sound from video software
marked . The PRO LOGIC mode uses the built-in adaptive matrix circuit to steer the Left, Center, Right and Surround channel audio signals.
The 3 STEREO mode will redirect the Surround signal to the front left and right speakers when only the front and center speakers are used. RC-R0508 2
systems (A, B) RC-R0508 2 systems (A, B) RC-R0710 1 system CENTER, Equipped SURROUND, (VIDEO 1) SUBWOOFER CENTER, Not equipped
SURROUND, SUBWOOFER SUBWOOFER Not equipped KRF-V6020 Preparations KRF-V5020 New DSP surround modes This manual is divided in to four
sections, Preparations, Operations, Other, and Remote Control. The DSP (Digital Signal Processor) used for this receiver incorporates a variety of high
quality adjustable sound fields, like "LIVE" and "HALL". It is compatible with almost any kind of program source. Preparations Shows you how to connect
your audio and video components to the receiver and prepare the surround processor.
We've tried to make setting up your system as easy as possible. However, since this receiver works with all of your audio and video components, connecting
the system can be fairly complex. DVD 6-channel input If you own a DVD player equipped with 6-channel output, this receiver allows you to obtain the full
surround sound impact of DVD source material featuring multi-channel encoding.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
Since the source signals are digital and each channel is input independently, the resulting ambience is far superior to what can be achieved with conventional
surround sound systems. Operations Shows you how to operate the various functions available from the receiver.
Universal IR (InfraRed) remote control (RC-R0508 only) In addition to the basic receiver, the remote control supplied with this receiver can also operate
almost all of your remote controllable audio and video components. Just follow the simple setup procedure to register the components you have connected.
Other Shows you additional information such as "In case of difficulty" (troubleshooting) and "Specifications." Remote Control (Separate booklet) (RC-R0508
only) Includes the "Quick Start Guide," which shows you how to operate other components using the remote control, as well as a detailed explanation of all
remote control operations. Once you have registered your components with the proper setup codes, you'll be able to operate both this receiver and your other
AV components (TV, VCR, LD player, CD player, etc.) using the remote control supplied with this receiver. MACRO play (RC-R0508 only) The MACRO
function lets you perform a series of operations automatically, like turning ON the power of the receiver and connected components, switching the input
selectors, and starting playback. (Be sure to register your components before starting the macro set up procedure. RDS (Radio Data System) tuner The
receiver is equipped with a RDS tuner that provides several convenient tuning functions: RDS Auto Memory, to automatically preset up to 30 RDS stations
broadcasting different programs; station name display, to show you the name of the current broadcast station; and PTY search to let you tune stations by
program type. PTY (Program TYpe) search Lets you tune stations by specifying the type of program you want to hear.
EON (Enhanced Other Networks) reservation The EON function lets you monitor information on other stations so you can receive traffic or news programs as
soon as they are broadcast, even they are broadcast on a station different from the one you are currently listening to. When the broadcast ends, the receiver
returns to the original station. When listening to KENWOOD source components connected with system control cords, the input selector on the receiver
automatically switches to the tuner when a program you desire is broadcast. Names and functions of parts KRF-V7020/V6020/V5020 (En/T) TI.VOL indicator
For KRF-V5020 Speaker indicator MUTE indicator SP SP Frequency display, Input display, Preset channel display, Surround mode display PRO LOGIC
indicator Band indicators FM MHz 3 STEREO MONITOR kHz DOWNMIX DSP 5 AUTO indicator MEMO. indicator ST. indicator S.DIRECT indicator
AUTO ST. TUNED A B TI.VOL L C R SW MUTE RDS EON PTY LS TP TA NEWS S RS ***** *;** Display AM PRO LOGIC S.
DIRECT MEMO. Speaker selection indicators Output channel indicators 1 2 3 45 6 7 8 9 AV SURROUND RECEIVER VOLUME CONTROL STANDBY PTY
TA/NEWS DISPLAY BAND AUTO MEMORY MULTI CONTROL INPUT SELECTOR ON / STANDBY - Oling. To access the functions printed above the keys,
press within 3 seconds of pressing the FUNCTION SHIFT key. Function availability varies for each component. 0 SHIFT key RC5 Use in combination with
the AUDIO and VIDEO keys to change the remote control mode without changing the input selector or in combination with the POWER key to turn on and off
components programmed into the remote control.
! TV selector key Sets the remote control to operate a TV or cable box. This key does not change the input selector on tents you are connecting. Do not
connect the power cord to a wall outlet until all connections are completed. Connecting audio components Shape of AC outlets For U.K.
Microcomputer malfunction If operation is not possible or an erroneous display appears, even though all connections have been made properly, reset the
microcomputer referring to "In case of difficulty". For other countries SYSTEM CONTROL jacks 0 To AC wall outlet Preparations Caution regarding
placement To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions, including projections) equal to, or
greater than shown below: Left and right panels: 10 cm, Rear panel: 10 cm, Top panel: 50 cm VIDEO 2/MONITOR jacks The receiver's VIDEO 2/MONITOR
jacks can be used in two different ways. Make the appropriate setting for the component connected to the jack when the receiver is turned on. Use as a VIDEO
2 jack You can connect a video deck or the like to these jacks and perform video playback and recording. The initial factory setting is "VIDEO 2". Use as a
MONITOR jack You can connect a cassette deck or the like to these jacks and make use of the deck's monitoring function during recording. Alternately, you
can connect a graphic equalizer to these jacks to apply compensation to the music signal. To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold
down the VIDEO 2/MONITOR key of the main unit for more two seconds so that the indication shown below appears. REC OUT PLAY IN REC OUT PLAY
IN L R PHONO CD MD / TAPE VIDEO 2 / MONITOR IN OUT ^ Cassette deck or graphic equalizer To use these jacks as MONITOR jacks, you must change
the appropriate setting. OUT VIDEO 2/MONITOR SP Cassette deck or MD recorder IN FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.
DIRECT MEMO. MHz AB MUTE L R SW MONIT O R STEREO MONITOR DSP ST. TUNED 7 6 kHz DOWNMIX 4 1 ¢ ¡ · At the same time the setting is
switched to "MONITOR," the audio input source switches to tuner and the video input source switches to VIDEO 1. · To switch the setting back to "VIDEO 2,"
once again hold down the VIDEO 2/MONITOR key for two seconds or more. · If you decide to use the VIDEO 2/MONITOR jacks as MONITOR jacks, make
sure to delete the "VIDEO 2 (VCR2)" input from the preset remote control (RC-R0508). RC6 OUT CD player OUT Notes 1. Be sure to insert all connection
cords securely. If their connections are imperfect, the sound may not be produced or noise may interfere. 2. Be sure to remove the power cord from the AC
outlet before plugging or unplugging any connection cords.
Plugging / unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. 3. Do not connect power
cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit. Record player To use the receiver
for video recording, connect a video deck to the VIDEO 2/MONITOR jacks. Setting up the system KRF-V7020/V6020/V5020 (En/T) Connecting video
components Even if your DVD player does not have the 6-channel output facility, you can enjoy the 6-channel audio by connecting a multi-channel surround
processor to your DVD player.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
9 6CH. INPUT VIDEO 1 SUB WOOFER CENTER VIDEO 2 VIDEO 1 SUB WOOFER CENTER VIDEO 2 MONITOR REC OUT PLAY IN PLAY IN
MONITOR FRONT SURROUND VIDEO 2 VIDEO OUT VIDEO IN DVD 6CH. INPUT FRONT VIDEO 2 / MONITOR VIDEO 1 SURROUND VIDEO 2
VIDEO OUT VIDEO IN DVD 6CH. INPUT FRONT Monitor TV SUBWOOFER CENTER VIDEO OUT SURROUND Multi-channel surround processor
Video Inputs (Yellow RCA pin cord) VIDEO IN DVD player Connecting the antennas DVD player or LD player OUT Video deck OUT IN Audio inputs and
outputs (Red and white RCA pin cords) OUT IN OUT Video inputs and outputs (Yellow RCA pin cords) Antenna terminal connections 1 Push lever. 2 Insert
cord.
3 Return lever. Connecting DVD 6-channel jack AM loop antenna The supplied loop antenna is for use indoors. Place it as far as possible from the receiver,
TV set, speaker cords and power cord, and adjust the direction for best reception. FM indoor antenna The supplied indoor antenna is for temporary use only.
For stable signal reception we recommend using an outdoor antenna. Disconnect the indoor antenna when you connect one outdoors. FM outdoor antenna
Lead the 75 coaxial cable connected to the FM outdoor antenna into the room and connect it to the FM 75 terminal. 6CH. INPUT VIDEO 1 SUB WOOFER
CENTER VIDEO 2 ANTENNA MONITOR AM loop antenna AM FRONT SURROUND VIDEO 2 VIDEO OUT VIDEO IN GND FM 75 DVD 6CH. INPUT FM
indoor antenna CENTER SURROUND FRONT SUBWOOFER VIDEO OUT Use an antenna adaptor (Commercially available) FM outdoor antenna DVD
player equipped with six channel output jacks, etc.
The sound input to DVD 6CH. INPUT is paired with the video signal input to 6CH. INPUT. Preparations Setting up the system KRF-V7020/V6020/V5020
(En/T) 10 Connecting the system control Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of
convenient system control operations. There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown
below. Notes 1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your equipment consists of this kind of
combination, please do not connect any system control cords. Even without system control cords, normal operations can be carried out without effecting
performance.
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
Preparations Mode : lets you combine f, , and Mode : for terminals only F terminals This unit is compatible with both [XS8] and [SL16] modes. It comes from
the factory set to the [SL16] mode. To switch to the [XS8] mode, follow the instructions in "SWITCHING FROM [SL16] TO [XS8]" below. SYSTEM
CONTROL cord SYSTEM CONTROL SYSTEM CONTROL cord Do not connect a system control cord to a cassette deck connected to the MONITOR jacks. ()
() SL16 (XS8) SYSTEM CONTROL SL16 (XS8) SYSTEM CONTROL OPERATIONS Remote Control Lets you operate this unit with the system remote
supplied with the receiver.
Automatic Operation (except [XR] equipment) When you start playback from a source component, the input selector on this unit switches to that component
automatically. Synchronized Recording (except [XR] equipment) Lets you synchronize recording with the start of playback when recording from CD, MD or
analog discs. SYSTEM CONTROL switch KRF-V5020 SYSTEM CONTROL switch KRF-V7020, KRF-V6020 EXAMPLE: [XS8] mode connections The
underlined portion represents the setting of the system control mode. [SL16] [XS8] [SL16] [SL16] [XS] [XS8] [XR] [SL16] [XS] [XS8] [XS] Receiver MD
recorder Cassette deck CD player Record player SYSTEM CONTROL cord SWITCHING FROM [SL16] TO [XS8] You can easily change the system control
mode by adjusting the position of the SYSTEM CONTROL switch on the rear panel. Do this operation after completing all connections. For [SL16] For [XS8]
For [SL16] For [XS8] EXAMPLE: [SL16] mode connections The underlined portion represents the setting of the system control mode. [SL16] [XS8] [SL16]
[XS] [XS8] [XR] [SL16] [XS] [XS8] [XS] Receiver Cassette deck or MD recorder CD player Record player SYSTEM CONTROL cord SL16 (XS8) SL16
(XS8) KRF-V5020 KRF-V7020, KRF-V6020 · This operation will not effect items stored in the memory. · After switching the system control mode, turn the
power off and unplug the power cord from the wall outlet, then plug it back. Registering setup codes for KENWOOD audio components (RC-R0508 only) ·
Once you finish making the system connections, be sure to register the appropriate setup code for each component. RC3 · If you own remote controllable
KENWOOD audio components that are not compatible with system control (or cannot be combined with your other system control components), registering
the setup code enables you to control those components using the remote control supplied with this unit (without connecting system control cords).
To register setup codes for your remote controllable KENWOOD audio components, see "Registering setup codes for other components". RC3 · In order to
take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must be connected to the CD
jacks. To use a cassette deck (or MD recorder) it must be connected to the MD/TAPE jacks. When using more than one CD player (etc.) only the one
connected to the specified jacks may be connected for system control. · Some CD players and cassette decks are not compatible with the [SL16] system control
mode. Be sure to use the [XS8] system control mode when making system connections with equipment that is not [SL16] compatible. · Some MD players are
not system control compatible. You cannot make system control connections to this kind of equipment.
Setting up the system KRF-V7020/V6020/V5020 (En/T) Connecting the speakers 1 Strip coating. 2 Loosen. 1 Strip coating. 2 Push lever. 11 3 Insert cord.
3 Insert. 4 Secure. 4 Return lever. · Never short circuit the + and speaker cords. · If the left and right speakers are connected inversely or the speaker cords
are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging.
Be sure to connect the speakers correctly. Front Speakers A Right Left The KRF-V5020 is equipped with one-touch speaker terminals. They are arranged in
the Center Speaker same manner as the speaker terminals of the KRF-V7020 /KRF-V6020. Refer to the instructions on making connections to the KRFV7020/KRFV6020 when making connections to the KRFV5020. + R L C Speaker impedance After confirming the speaker impedance indications printed on
the rear panel of the receiver, connect speakers with matching impedance ratings.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or damage to the speakers or
receiver. PRE OUT connections This receiver has additional preout jacks. These can be used for various purposes, but will need to be connected to an
external power amplifier as shown in the example below. A + + R L C CENTER FRONT SPEAKERS SPEAKER - - FRONT SPEAKERS CENTER SPEAKER
KRF-V7020, KRF-V6020 KRF-V5020 CENTER L Power amplifier R SUB WOOFER SURROUND Surround Speakers Powered Subwoofer PRE OUT
CENTER FRONT SPEAKERS R L L + - B - + R SUB WOOFER SURROUND Center Speaker + + PRE OUT Powered subwoofer Use the FRONT
SPEAKERS B terminals if you want to connect a second front speaker system. (KRF-V5020 is not equipped with SPEAKERS B terminal.
) R L Power amplifier · Connecting a speaker cord directly to a PRE OUT jack will not produce any sound from the speaker. · To use the PRE OUT jacks,
press the SPEAKERS A key to the on position (the SPEAKERS key in the case of the KRF-V5020). SURROUND SPEAKERS Left Right Surround Speakers (Be
sure to connect both surround speakers) Preparations Setting up the system KRF-V7020/V6020/V5020 (En/T) 12 Speaker placement Preparing the remote
control (RC-R0508) Loading the batteries 1 Remove the cover. Center speaker 2 Insert the batteries. Preparations Subwoofer Front speaker Surround
speaker Listening position 3 Close the cover. Front speakers : Place to the front left and right of the listening position. Front speakers are required for all
surround modes. Center speaker : Place front and center. This speaker stabilizes the sound image and helps recreate sound motion. Be sure to connect a
center speaker when using the Dolby 3 Stereo mode.
Surround speakers : Place to the direct left and right, or slightly behind, the listening position at even heights, approximately 1 meter above the ears of the
listeners. These speakers recreate sound motion and atmosphere. Required for surround playback. Subwoofer : Reproduces powerful deep bass sounds. ·
Although the ideal surround system consists of all the speakers listed above, if you don't have a center speaker or a subwoofer, you can divide those signals
between the available speakers in the speaker settings to obtain the best possible surround reproduction from the speakers you have available.
# · Insert four AAA-size (LR03) batteries as indicated by the polarity markings. Operation When the STANDBY indicator is lit, the power turns ON when you
press the POWER key on the remote control. When the power comes ON, press the key you want to operate. Operating range (Approx.) Remote sensor 10 m
6m 30° 30° Model: RC-R0508 Infrared ray system · When pressing more than one remote control key successively, press the keys securely by leaving an
interval of 1 second or more between keys.
Notes 1. The supplied batteries may have shorter lives than ordinary batteries due to use during operation checks. 2. Replace all four batteries with new ones
when you notice a shortening of the distance from which the remote control will operate or if the remote control blinks 5 times when you press a key. The
remote control is designed to retain set up codes in memory while you change batteries. 3. Placing the remote sensor in direct sunlight, or in direct light from
a high frequency fluorescent lamp may cause a malfunction. In such a case, change the location of the system installation to prevent malfunction. Setting up
the system Preparing for surround sound KRF-V7020/V6020/V5020 (En/T) Preparing the remote control (RC-R0710) Loading the batteries 1 Remove the
cover. 2 Insert the batteries.
Speaker settings To enable you to obtain optimum enjoyment from the receiver's listening modes, make sure to complete the speaker settings as described
below. 13 SETUP MULTI CONTROL 3 Close the cover. VIDEO MULTI CONTROL TUNING/SKIP SETUP · Insert two AA-size (R6) batteries as indicated by
the polarity markings. RC-R0508 SETUP Operation When the STANDBY indicator is lit, the power turns ON when you press the POWER key on the remote
control. When the power comes ON, press the key you want to operate. Operating range (Approx.) 1 Turn on the receiver. 2 Select a speaker system. SP RCR0710 $ 1 Press the SETUP key to make the subwoofer setting indication (SUBW) appear. A L R SW Remote sensor sUBW Y Es STEREO 2 Use the MULTI
CONTROL (TUNING/SKIP) to select the appropriate subwoofer setting.
1 SUBW YES: A subwoofer is connected to the receiver. 2 SUBW NO: No subwoofer is connected to the receiver. 3 Press the SETUP key to accept the setting.
· The center speaker setting indication (CNTR) appears. SP 6m 30° 30° A L R SW CNTR N ML STEREO 4 Use the MULTI CONTROL (TUNING/SKIP) to
select the appropriate center speaker setting.
Model: RC-R0710 Infrared ray system · When pressing more than one remote control key successively, press the keys securely by leaving an interval of 1
second or more between keys. 1 CNTR NML (normal): 2 CNTR LRG (large): 3 CNTR NO: An average size center speaker is connected to the receiver. A
large center speaker is connected to the receiver. No center speaker is connected to the receiver. Notes 1.
The supplied batteries may have shorter lives than ordinary batteries due to use during operation checks. 2. When the remote-controllable distance gets
shorter than before, replace both batteries with new ones. 3. Placing the remote sensor in direct sunlight, or in direct light from a high frequency fluorescent
lamp may cause a malfunction. In such a case, change the location of the system installation to prevent malfunction. 5 Press the SETUP key to accept the
setting. · The surround speaker setting indication (SURR) appears. 6 Use the MULTI CONTROL (TUNING/SKIP) to select the appropriate surround speaker
setting. 1 SURR YES: Surround speakers are connected to the receiver.
2 SURR NO: No surround speakers are connected to the receiver. 7 Press the SETUP key to accept the setting. · The receiver enters the speaker volume level
adjustment mode. · In steps 3 and 4, indications appear only for the selected channels of the speakers that require adjusting. Continued to next page
Preparations Preparing for surround sound Normal playback KRF-V7020/V6020/V5020 (En/T) 14 Preparing for playback 3 Adjust the volume levels for the
speakers. Sit in your normal listening position and listen to the test tone. Adjust the volume levels for the speakers until all speakers seem to be equally loud. 1
Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume when the test tone is being output from the speaker channel to be adjusted. Some
preparatory steps are needed before starting playback. VIDEO 2/MONITOR ON/STANDBY AUTO Preparations Operations The channel indication blinks
while the test tone is being output.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
SP A L SW The test tone issues from the speakers for 2 seconds at a time in the following sequence: Lch = Cch = Rch = Sch = Lch · If you change the volume
level settings for the speakers while listening to music, the settings referred to on this page are also changed. ¢ · If the speaker setting selects are changed, the
speaker level settings are reset. 2 Press the SETUP key. Lch + 1 dB POWER INPUT SELECTOR SPEAKERS A/B SPEAKERS, MUTE (KRF-V5020) Turning
on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER and ON/ STANDBY keys.
Selecting TAPE/MD · The receiver enters the mode for inputting the distance to the speakers. Select the source name corresponding to the component
connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source name associated with the MD/TAPE jacks to "MD," follow the
steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". 2 Hold down the AUTO key for more than two seconds.
· The source indication changes to "MD". · To return to the original indication, repeat the above procedure. · You also will need to change the name input to
the remote control (RC-0508) to "MD". RC3 4 Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers.
Jot down the distance to each of the speakers. Distance to front speakers: ____ feet (meters) Distance to surround speakers: ____ feet (meters) 2 Use the
MULTI CONTROL (TUNING/SKIP) to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP Selecting the speaker system
Press the SPEAKERS A or B key to select the speaker system to be used. : Sound from the speakers connected to the SPEAKERS A terminals on the rear
panel.
B ON : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. A+B ON : Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel. A+B OFF : No sound from the speakers. Use this setting when listening with headphones for stereo sound in
all playback modes. A ON · Activating a surround mode or selecting "DVD 6ch" as the input source causes speaker system A to be selected automatically. On
the KRF-V5020, press the SPEAKERS key to switch the speakers on and off. A L R Indication in feet 1)FT 3.)M Indication in meters · The allowable setting
range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.
3 m) increments. 3 Press the SETUP key. 4 Repeat steps 2 and 3 to input the distance for the surround speaker. @@· The speakers you selected appear on the
display. @@@@@@1 Press the SOUND key to select the tone mode to be adjusted.
@@the SOUND key once.) this to adjust the high frequency range. @@@@@@@@@@@@@@@@@@@@@@Press the BASS BOOST key.
@@@@@@@@@@@@2 Set the cassette deck to record. @@Press the SOURCE DIRECT key.
AUTO SOUND AUTO S.DIRECT MEMO. ST. @@@@ST. @@@@@@@@@@@@@@@@Alternately, if a cassette deck equipped with a 3-head system
is connected to the VIDEO2/MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching
the VIDEO2/MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the
instruction manual of the connected component. To adjust the input level when the monitor function is turned on, use the SOUND key and the MULTI
CONTROL key. ¢ · If you turn off all of the speakers when in the surround mode, the mode is cancelled as well, resulting in stereo playback. 2 Connect
headphones to the PHONES jack.
PHONES 3 Use the VOLUME CONTROL knob (VOLUME) to adjust the volume. Recording video When recording video, switch the VIDEO2/MONITOR
setting to "VIDEO2". 8 1 Use the input selector to select the video source (other than "VIDEO2") you want to record. 2 Set the video deck connected to
VIDEO2/MONITOR to record. 3 Start playback, then start recording. To adjust the balance Use the test tone feature. $-3 Listening to radio broadcasts KRFV7020/V6020/V5020 (En/T) Tuning (non-RDS) radio stations Radio stations can be classified into RDS (Radio Data System) stations and other stations. To
listen to or store RDS stations in the preset memory, see the section entitled, "Using RDS". Using RDS (Radio Data System) RDS is a system that transmits
useful information (in the form of digital data) for FM broadcasts along with the broadcast signal. Tuners and receivers designed for RDS reception can
extract the information from the broadcast signal for use with various functions, such as automatic display of the station name.
17 AUTO BAND RDS functions: PTY (Program Type Identification) Search ) Automatically tunes to a station that is currently broadcasting the specified
program type (genre). MULTI CONTROL INPUT SELECTOR EON (Enhanced Other Network) reservation ) Sets the tuner to automatically switch to stations
broadcasting one of two types of programs, even though you are listening to another station. The tuner returns to the original station when the broadcast of
the selected program ends. PS (Program Service Name) Display Automatically displays the station name transmitted by the RDS station. RDS Auto Memory
function * Automatically selects and stores up to 30 RDS stations in the preset memory.
If fewer than 30 RDS stations have been stored in the preset memory, regular FM stations will be stored in the remaining places. Radio text function Displays
the radio text data transmitted by some RDS stations when you press the DISPLAY key. There is no display if no text data was transmitted. The "RDS"
indicator lights up when an RDS broadcast (signal) is received. SP A B TI.
VOL MUTE RDS EON PTY TP TA NEWS AUDIO BAND (AUTO) TUNING/SKIP TUNER AUTO BAND MULTI CONTROL 1 Use the input selector to select
the tuner. 2 Use the BAND key to select the desired broadcast band. Each press switches the band as follows: "AM" or "FM" indicator 1 FM 2 AM 8 7.5) FM
AUTO ST. MEMO. MHz STEREO L R SW TUNED 3 Use the AUTO key to select the desired tuning method. Each press switches the tuning method as
follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) -- 9 2.5) FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO. MHz
STEREO MONITOR DSP ST.
TUNED kHz DOWNMIX 8 7.5) FM MHz AUTO MEMO. Note Some functions and function names may differ for certain countries and areas. STEREO ST.
TUNED · Normally, set to "AUTO" (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning,
stereo broadcasts will be received in monaural.) Before using a function utilizing the RDS, be sure to perform the RDS Auto Memory operation by referring to
the description in "Presetting RDS stations (RDS AUTO MEMORY)".
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
@@@@@@@@@@MHz Operations STEREO MONITOR DSP ST. @@MHz STEREO MONITOR DSP ST.
@@MHz STEREO MONITOR DSP ST. @@@@@@@@MHz STEREO MONITOR DSP ST. TUNED kHz DOWNMIX 3 Frequency display: Displays the
frequency of the current station. SP A B TI.VOL MUTE RDS EON PTY TP TA NEWS L R SW FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.
DIRECT MEMO. MHz STEREO MONITOR DSP ST. TUNED kHz DOWNMIX Listening to radio broadcasts KRF-V7020/V6020/V5020 (En/T) Presetting
radio stations manually The RDS auto memory function assigns preset numbers to RDS stations starting from preset number "1". Therefore, be sure to
execute the RDS auto memory function before using the following operations to manually store AM stations and other FM stations, and RDS stations.
"Presetting RDS stations (RDS AUTO MEMORY)".
* 2 Enter the number of the preset you want to receive (up to "30"). Press the numeric keys in the following order: For "15", press .........
. 0,5 For "20", press .........
. 0,0,) · If you make a mistake entering a two digit number, press the +10 key several times to return to the original display and start again. SP 19 MEMORY
A L R SW 15 8 9.)) FM MHz AUTO MEMO. STEREO ST.
TUNED MULTI CONTROL 1 Tune to the station you want to store. 2 Press the MEMORY key while receiving the station. Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again). · When storing radio stations manually, it may take a few seconds before the "MEMORY"
indicator appears in the display after pressing the MEMORY key depending on receiving conditions.
Blinks for 5 seconds SP Receiving preset stations in order (P.CALL) AUDIO P.CALL P.CALL TUNER Lights for 5 seconds A L R SW 01 8 9.)) FM MHz
AUTO MEMO. STEREO ST. TUNED RC-R0508 RC-R0710 3 Use the MULTI CONTROL to select one of the station presets (1 30). 1 Use the remote control
to select the tuner as the source. · The remote control switches to the tuner operating mode. 4 Press the MEMORY key to accept the setting.
· Repeat steps 1, 2, 3 and 4 to store as many stations as necessary. · If you store a station at a previously used preset, the old station will be replaced by the
new one. 2 Use the P.CALL key to select the desired station. · Each time you press the key, another preset station is received in order. Pressing the P.CALL
(%) key (¢) does the following: 01=02=03= ....
.. 28=29=30=01=02=03= Pressing the P.CALL (fi) key (4) does the following: 01+02+03+ ..
.... 28+29+30+01+02+03+ Holding down the key, lets you skip through the presets, receiving each for 0.
5 seconds apiece. Receiving preset stations AUDIO 1-0, +10 TUNER 1-0, +10 RC-R0508 RC-R0710 1 Use the remote control to select the tuner as the
source. · The remote control switches to the tuner operating mode. Operations Listening to radio broadcasts KRF-V7020/V6020/V5020 (En/T) 20 Tuning by
program type (PTY search) This function lets you set the tuner to automatically search for stations which are currently broadcasting the type of program
(genre) you want to listen to. Under certain receiving conditions, it may take more than 1 minute to complete the search. "NO PROG" is displayed if this
operation is attempted before performing the RDS Auto Memory operation. 3 Press the PTY key to start searching. EXAMPLE: Searching for a Rock Music
broadcast. Display while searching Blinks A B TI.VOL MUTE RDS EON PTY TP TA NEWS SP PTY L R SW Program type name display ROCK M FM AUTO
SOUND DIGITAL AUTO AM PRO LOGIC S.
DIRECT MEMO. MHz STEREO MONITOR DSP ST. TUNED kHz DOWNMIX MULTI CONTROL Display when a station is received. Goes out A B TI.VOL
MUTE RDS EON PTY TP TA NEWS SP L R SW BBC 1 FM Station name display FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR DSP ST. TUNED kHz DOWNMIX MULTI CONTROL PTY · No sound is heard while "PTY" is blinking. · If the desired program
type cannot be found, "NO PROG" is displayed, then after several seconds the display returns to the original display. RC-R0710 Operations Preparations ·
Execute the RDS auto memory procedure.
· Set the broadcast band to FM. · Tune to an RDS station. To select another program type Repeat steps 1, 2 and 3. 1 Press the PTY key to activate the PTY
search mode. SP A BTI.
VOL MUTE RDS EON PTY TP TA NEWS Reserving the desired information When the receiver is tuned to a RDS EON station (a station at which the EON
indicator lights up), this function lets you set the receiver to automatically switch stations to receive news or traffic programs as they are broadcast. When the
broadcast is over, the receiver returns to the original station automatically. L R SW NEWs FM AM MHz kHz AUTO SOUND DIGITAL AUTO S.DIRECT
MEMO. PRO LOGIC STEREO MONITOR ST.
TUNED DOWNMIX DSP When an RDS broadcast is received, the program type is shown on the display. If no PTY data is available, or if the station is not an
RDS station, "NONE" is displayed. 2 While the "PTY" indicator is lit, use the MULTI CONTROL to select the program type of your choice. Display POP M
ROCK M M.O.R. M LIGHT M CLASSICS OTHER M NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED TA/NEWS Program
type table Program Type Name Pop Music Rock Music *M.O.R. Music Light Classic Music Serious Classic Music Other Music News Current Affairs
Information Sport Education Drama Cultures Science Varied Speech Program Type Name Weather Finance Children's programmes Social affairs Religion
Phone in Travel Leisure Jazz music Country Music National Music Oldies Music Folk Music Documentary Display WEATHER FINANCE CHILDREN
SOCIAL A RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT VOLUME CONTROL VOLUME
TA/NEWS *M.
O.R. Music (Middle of the Road Music) RC-R0710 Preparation · Set the broadcast band to FM. Listening to radio broadcasts KRF-V7020/V6020/V5020
(En/T) 1 Complete steps 1~3 of "Presetting RDS stations (RDS AUTO MEMORY)". 21 When waiting for information while listening to a RDS station without
the EON function If the "EON" indicator does not light in steps 3 and 4 and the desired kind of information has already been selected, the information from
only the station being received will be waited for. * Skip this step if you have already completed the RDS AUTO MEMORY procedure. · The EON function will
not work if all 30 FM preset stations were stored manually using the procedure shown in "Presetting radio stations manually". Be sure to use the RDS
automatic memory function. 2 Press the TA/NEWS key to select the information type of your choice. SP A B TI.
VOL MUTE RDS EON PTY TP TA NEWS TP (Traffic Program) indication When the "TP" indicator is lit, this means that the presently-received station or a
station in the same network is transmitting traffic information.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
When "TP" is displayed for the station being received, the traffic information of this station can be received without EON reservation. Display When "TA" is
selected L R SW BBC 1 FM FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO. MHz STEREO MONITOR DSP ST.
TUNED kHz DOWNMIX "TP" lights for stations where TP (Traffic Program) information can be received. Each press switches the reservation mode as
follows: 1 TA 2 NEWS 3 TA, NEWS 4 off (Traffic Announcement) (News) (Traffic Announcement and News) (EON off) To cancel EON reservation Turn the
"TA" and "NEWS" indicators off. Setting the volume while receiving information (TI volume) Operations If you preset the volume level, you can listen to the
information of your choice at that volume level automatically. After the information has been received, the volume returns to the previous level. 1 Hold down
the TA/NEWS key for more than two seconds so that the "TI.
VOL" indicator starts blinking. SP A B TI.VOL MUTE RDS EON PTY TP TA NEWS · If "TA" and "NEWS" can not be selected, carry out the RDS automatic
memory function again. * 3 Tune to a preset RDS station. Choose an RDS preset station that displays both the "RDS" and "EON" indicators. Display When
"TA" is selected SP L R SW A B TI.VOL L R SW MUTE RDS EON PTY TP TA NEWS Be sure "EON" appears in the display BBC 2 FM FM AUTO SOUND
DIGITAL AUTO AM PRO LOGIC S.DIRECT MEMO. MHz STEREO MONITOR DSP ST. TUNED Blinks TI -5 ) dB FM AUTO SOUND DIGITAL AUTO AM
PRO LOGIC S.
DIRECT MEMO. MHz STEREO MONITOR DSP ST. TUNED kHz DOWNMIX kHz DOWNMIX · If you want to reserve TA, receive a station with which the
TP indicator lights. · When "EON" does not light although an RDS station is received, that station is not transmitting EON data. Please select a different
station. 2 Use the VOLUME CONTROL knob to select the desired volume level. Proceed to next step within five seconds. 3 Press the TA/NEWS key to enter
the new setting. · The "TI.VOL" indicator stops blinking and remains lit.
4 Wait for the information you selected while listening to the current station. The receiver will wait for the desired information to start as long as the tuner is
set to a preset RDS station that displays both the "EON" and "RDS" indicators, and the power is turned ON. When listening to the tuner: Be sure to stay tuned
to stations that display both the "EON" and "RDS" indicators. To listen sources other than the tuner: 1 Tune in a station which that displays both the "EON"
and "RDS" indicators, then use the INPUT SELECTOR to switch the input to the source you desire. 2 Even when the INPUT SELECTOR is set to a source
other than tuner, it will automatically switch to tuner when the desired EON program starts to broadcast.
During this period, the source selected in step 1 continues playing, but will not be heard. 3 When reception of the desired EON program is complete, the
INPUT SELECTOR returns to the previous input source. · When the power is OFF, the EON function does not operate. · If a reserved EON program starts to
broadcast during analog recording, the INPUT SELECTOR switches to the tuner and the station broadcasting the EON program is recorded. Canceling TI
volume Hold down the TA/NEWS key for more than two seconds so that the "TI.
VOL" indicator goes off. Ambience effects KRF-V7020/V6020/V5020 (En/T) 22 This receiver is equipped with listening modes that allow you to enjoy an
enhanced sonic ambience with a variety of video sources. In order to obtain the optimum effect from the surround modes, make sure to input the proper
speaker settings beforehand. # DSP mode The DSP mode lets you add the atmosphere of a live concert or hall to almost any type of program source. These
modes are particularly effective when used with stereo program sources, like CD, television, and FM radio. You might enjoy trying the LIVE or HALL mode
the next time you watch a concert or sporting event! Manufactured under license from Dolby Laboratories. "DOLBY", the double-D symbol and "PRO
LOGIC" are trademarks of Dolby Laboratories. Surround modes Dolby Pro Logic Dolby Pro Logic is a specially encoded 2 channel surround format
designed to provide theater-like surround sound from Dolby Surround encoded sources (such as video and Laserdisc software ). marked This receiver is
equipped with a Dolby Pro Logic surround decoder to let you enjoy the wide variety of currently available Dolby Surround home video software. Subwoofer
Front speaker Surround speaker What's DSP? DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a variety of different factors. One of the most important is reverberation (the act of decaying
elements of sound echoing in various places). The DSP modes produce the feeling of presence by using the DSP to create reverberation, without spoiling the
sound quality of the original signal. Center speaker Operations DVD 6-channel mode Subwoofer Front speaker Surround speaker Using a DVD player or the
like equipped with six (5.1) output channels and the receiver, you can enjoy multi-channel encoded DVD source material in all its splendor. Since the source
signals are digital and each channel is input independently, the resulting sound quality, sense of spaciousness, and dynamic range are superb. Center speaker
Dolby 3 Stereo Dolby 3 Stereo is available for systems that do not have surround speakers. When in the Dolby 3 Stereo mode, the surround information is
redirected to the front left and right speakers. This mode is designed for use with Dolby Surround program sources, but can also improve sound field unity for
programs that are not Dolby Surround encoded. Dialog positioning and sound image definition, however, may not be as accurate when used with programs
that are not Dolby Surround encoded.
Center speaker Subwoofer Front speaker Surround speakers Subwoofer Front speaker Ambience effects KRF-V7020/V6020/V5020 (En/T) Surround Play
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing video, DVD, or LD software bearing the mark. DSP modes can be used with any
source. DVD 6-channel playback Using a DVD player or the like equipped with six (5.1) output channels and the receiver, you can enjoy surround sound
playback. When you try to play a disc other than Dolby Digital (AC-3) such as DTS CD, no sound is produced or, noise may be heard.
To avoid this situation, make sure that you connect the component to the receiver's DVD 6CH. INPUT jacks through a surround processor which can decode
the surround signal you wont to listen to. Connecting a DVD player which can decode the surround signal itself is also acceptable.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
23 LISTEN MODE INPUT SELECTOR LISTEN MODE LISTEN MODE VIDEO DVD/6CH INPUT Preparations · Turn ON related components. · Complete
"Preparing for surround sound".
# · Set the INPUT SELECTOR to the component you wish to play back with surround sound. RC-R0508 RC-R0710 Preparations · Connect your DVD player
to the DVD 6ch jacks of the receiver. · Turn on all other components that will be used. · Complete "Preparing for surround sound". # 1 Start playing the video
software. 2 Press the LISTEN MODE key to select the listening mode. Listening mode settings are stored independently for each input. Each press of the
LISTEN MODE key switches the setting as listed below. Note that the only listening mode settings that can be used for playback with the current speaker
settings are available. · · · · · DOLBY PRO LOGIC DOLBY 3 STEREO LIVE (DSP) HALL (DSP) STEREO 1 Select "DVD 6ch" as the input source.
· If speaker system B is on when "DVD 6ch" is selected as the input source, it switches off and speaker system A turns on automatically (models other than
KRF-V5020). 2 Start playback of the DVD software. 3 Adjust the volume. · It is not possible individually to adjust the volume level or sound quality (SETUP,
SOUND) of the separate channels when the receiver is in the DVD 6ch mode. Adjust the volume with the controls of the DVD player. For the powered
subwoofer, you can adjust the volume of the subwoofer using the subwoofer's own volume control. · When in the DVD 6ch mode, you can still use the volume
control, mute, SPEAKERS (A) key, and dimmer functions. Example with the DOLBY PRO LOGIC mode selected The channels from which sound will issue are
displayed. SP AB L C S R SW PRO L O GI AUTO SOUND AUTO MEMO. ST.
TUNED PRO LOGIC 3 Adjust the volume. Operations RC-R0508 RC-R0710 Ambience effects KRF-V7020/V6020/V5020 (En/T) 24 Convenient functions
DISPLAY MULTI CONTROL SUBWOOFER adjustment (RC-R0508 only) It is easy to adjust the volume of the subwoofer using the remote control (RCR0508). 1 Press the SUBWOOFER key so that "SW" is displayed. SP AB L LS C R LFE SW S RS SOUND sW ) dB AUTO SOUND DIGITAL AUTO PRO
LOGIC MEMO. ST.
TUNED 2 Use the VOLUME key to adjust the volume. · The adjustable range is -10 dB to +10 dB. VOLUME TUNING/SKIP SUBWOOFER SOUND RCR0508 MULTI CONTROL SOUND Display dimmer adjustment The dimmer function lets you select the brightness of the receiver's display. You might find
this useful if you darken your room to watch movies or listen to music. RC-R0710 Each time you hold down the DISPLAY key for more than two seconds, the
display brightness changes among the three available settings.
Select the brightness level you find most pleasing. SP Adjusting the sound You can make further adjustments to the sound while listening to playback in the
surround mode. AB L C S R SW 1 Press the SOUND key to select the item you want to adjust. Each press switches the selection as listed below. Note that
some items are not displayed in certain modes. BASS (low frequency range sound quality adjustment) TREB (high frequency range sound quality adjustment)
Cch (center speaker level adjustment) Sch (surround speaker level adjustment) SW (subwoofer level adjustment) INPUT (input level adjustment) % % SP
VIDEO1 VIDEO1 VIDEO1 Operations PRO LOGIC SP AB L C S R SW PRO LOGIC AB L C S R SW PRO LOGIC · The adjustment item for input level is
displayed only when the monitor function is activated. 2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the setting as desired. @@· If you use the
remote control (RC-R0508) to perform the above setting, press the VIDEO key at this point to turn off the remote control's own adjustment mode. In this case,
the input source is not switched. Input level adjustment (when using the monitor function) If the input level while using the monitor function is too high, adjust
the input level as described below.
1 Turn on the monitor function. ^ 2 Press the SOUND key several times until the "INPUT" indication appears. 3 Use the MULTI CONTROL (TUNING/SKIP)
to adjust the input level. SP AB L R SW INPUT -6 AUTO SOUND AUTO MEMO. ST. TUNED STEREO MONITOR · The adjustment mode is displayed for
approximately 8 seconds. · The input level may be adjusted to any one of two settings: 0 and 6. (The initial setting is 0.) 4 Press the SOUND key to return to
the input indication. In case of difficulty KRF-V7020/V6020/V5020 (En/T) Resetting the Microcomputer If the microcomputer may malfunction (unit cannot be
operated, or shows an erroneous display) if the power cord is unplugged while the power is ON, or due to some other external factor.
If this happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition. 25 With the power cord
plugged in, turn the POWER key OFF. Then, while holding down the ON/STANDBY key, press POWER. · Please note that resetting the microcomputer will
clear the contents of the memory and returns the unit to the state it was in when it left the factory. Amplifier Symptom No sound from the speakers.
Cause · The speaker cords are disconnected. · VOLUME is set to the minimum position. · MUTE is ON. · The SPEAKERS switches are set to OFF. The
standby indicator blinks and sound is not output.
Sound is not output from one of the speakers. · Speaker cords are short-circuited. Remedy · Connect them properly referring to "Connecting the speakers" ! ·
Adjust the volume to a proper level. · Turn OFF the MUTE. ^ · Set the SPEAKERS switch(es) to ON. $ · Turn the power off, eliminate the short-circuiting, then
turn on the power again. ! · Connect it properly referring to "Connecting the speakers". · Connect it properly referring to "Connecting the speakers". · Select
a surround mode. · Adjust the speaker levels using the test tone.
$ · Insert the audio cord plugs securely into the PHONO jacks. · Connect the grounding wire to the GND terminal on the rear panel. · The speaker cord is
disconnected. Sound is not output from the surround speakers and / or the center speaker, or their sound is very small. · The surround speaker cords and/or
the center speaker cord is disconnected. · A surround mode has not been engaged. · The surround and/or center volume controls are set to the minimum level.
· The audio cord from the turntable is not connected to the PHONO jacks. · The turntable is not grounded. A humming noise is generated when the PHONO
input selector is selected.
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
Tuner Symptom Radio stations cannot be received. Cause · No antenna is connected. · The broadcast band is not set properly. · The frequency of the desired
station is not tuned. · Noise due to ignition noise from an automobile.
· Noise due to interference from an electric appliance. · Noise due to a nearby TV set. · The preset station belongs to a frequency that cannot be received. · The
preset memory was cleared because the power cord had been unplugged for a long period of time. Remedy · Connect an antenna.
· Set the broadcast band properly. · Tune the frequency of the desired station. & · Install the outdoor antenna away from the road. · Turn off the power to the
appliance. · Install the receiver farther away from the TV. · Preset a station with a receivable frequency. · Preset the station again. Interference. A station
which was preset cannot be received by pressing the corresponding numeric key. Other In case of difficulty KRF-V7020/V6020/V5020 (En/T) Remote control
unit 26 Symptom Remote control operation is not possible.
Cause · Batteries are exhausted. · The remote control unit is too far away from the main system, controlling angle is too large, or there is an obstacle between
the receiver and the remote. · The audio cords and system control cords are not connected properly. · No software is loaded in the source component. · An
attempt is made to play a tape which is being recorded in the cassette deck. Remedy · Replace with new batteries. @# · Operate the remote control unit within
the controllable range. · Connect properly referring to "Setting up the system". 8 · Place software in the source component you want to play. · Wait until
recording has completed.
Other Memory back up function Please note that the following items will be deleted from the unit's memory if the power cord is disconnected from the AC
outlet or the main power switch is turned off for approximately 3 days. · Power mode. · Input selector settings. · Volume level. · Broadcast band.
· Frequency setting. · Preset stations. Specifications AUDIO section Rated power output during STEREO operation KRF-V7020 (DIN) 1 kHz, 0.7% at 4 ..
..........
..........
.....
.....
..........
100 W + 100 W KRF-V6020, KRF-V5020 (DIN) 1 kHz, 0.7% at 4 .........
.....
.....
..........
..........
.....
... 80 W + 80 W Effective power output during SURROUND operation KRF-V7020 FRONT (1kHz, 0.7% T.
H.D. at 4 one channel driven) ........
..........
.....
.....
..........
..........
.....
.....
..........
..........
100 W + 100 W CENTER (1kHz, 0.7% T.H.D. at 4 one channel driven) .
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.. 100 W SURROUND (1kHz, 0.7% T.H.
D. at 4 one channel driven) .........
..........
.....
.....
..........
..........
.....
.....
..........
......... 100 W + 100 W KRF-V6020, KRF-V5020 FRONT (1kHz, 0.
7% T.H.D. at 4 one channel driven) ..
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..... 80 W + 80 W CENTER (1kHz, 0.7% T.H.D. at 4 one channel driven) .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.... 80 W SURROUND (1kHz, 0.
7% T.H.D. at 4 one channel driven) ..
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
80 W + 80 W Total harmonic distortion .....
.....
..........
....... @@@@@@@@2.5 mV / 27 k CD ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
. 200 mV / 47 k DVD 6CH (SUBWOOFER) .........
..........
.....
.....
...... 200 mV / 10 k Output level / impedance TAPE REC ....
..........
.....
.....
..........
..........
.....
.....
.... 200 mV / 2.2 k PRE OUT (CENTER, SURROUND) .....
..........
.....
.....
.. 1 V / 2,2 k PRE OUT (SUBWOOFER) ........
..........
.....
.....
..........
... 2 V / 2.2 k Tone control BASS ......
.....
.....
..........
..........
.....
.....
..........
....... @@@@@@@@1.2 µV / 13.2 dBf (40 kHz DEV.
, S/N 26 dB) STEREO .....
.....
........ 45 µV / 44.2 dBf (46 kHz DEV.
, S/N 46 dB) Total harmonic distortion (DIN, 1 kHz) MONO ..........
.....
.....
..........
..........
.....
.....
....... 0.2% (65.2 dBf input) STEREO .
..........
.....
.....
..........
..........
.....
.....
... 0.8% (65.2 dBf input) Signal to noise ratio (DIN weighted, 1 kHz) MONO .....
..........
.....
.....
....... 65 dB (40 kHz DEV., 65.2 dBf input) STEREO .
..........
.....
.....
....... 60 dB (46 kHz DEV., 65.2 dBf input) Stereo separation (DIN, 1 kHz) .
..........
.....
.....
..........
..........
.....
.... 36 dB Selectivity (DIN, ±300 kHz) .
..........
..........
.....
.....
..........
..........
.....
64 dB Frequency response (30 Hz ~ 15kHz) .....
..........
... +0.5 dB, 3.0 dB AM tuner section Tuning frequency range .....
.....
.....
..........
..........
. 531 kHz ~ 1,602 kHz Usable sensitivity (30% mod., S/N 20 dB) ...
.....
..........
..........
.....
.....
..........
..........
.....
.....
.... 16 µV / (600 µV/m) Signal to noise ratio (30% mod., 1 mV input) .....
..........
.....
.....
. 50 dB GENERAL Power consumption .........
..........
.....
.....
..........
..........
.....
.....
....... 230 W AC outlet SWITCHED ...
..........
.....
.....
..........
..........
.....
.. 2 (total 150 W max.) Dimensions ..
..........
..........
.....
.....
..........
..........
.....
.....
......... W : 440 mm H : 144 mm KRF-V7020 .
..........
.....
.....
..........
..........
.....
.....
..........
.... D : 400 mm KRF-V6020, KRF-V5020 ......
.....
.....
..........
..........
.....
... D : 390 mm Weight (Net) KRF-V7020 ..
..........
..........
.....
.....
..........
..........
.....
.....
..........
.. 9.2 kg KRF-V6020 .......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.. 8.4 kg KRF-V5020 ..
..........
..........
.....
.....
..........
..........
.....
.....
..........
.. 8.2 kg Notes 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2.
The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature). Other For your records Record the serial
number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your dealer for information or service on this product.
Model __________________ Serial Number _______________________ .
You're reading an excerpt. Click here to read official KENWOOD
KRF-V5020 user guide
http://yourpdfguides.com/dref/126580
Powered by TCPDF (www.tcpdf.org)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising