PRSF-15
Functional Smith Trainer
2013 06 Rev A
Assembly Manual
Contents
Safety Instructions -------------------------------------------------------------------------------------- Page 2
Floor Plan Diagram---------------------------------------------------------------------------------------- Page 3
Parts List------------------------------------------------------------------------------------------------------ Page 4
Parts Reference ------------------------------------------------------------------------------------------ Page 5
Hardware List-----------------------------------------------------------------------------------------------Page 6
Hardware Chart--------------------------------------------------------------------------------------------
Page 7
Components Pre-installed in the Parts-----------------------------------------------------------
Page 8
Pre-installed Parts References ----------------------------------------------------------------------- Pages 9-13
Assembly Steps---------------------------------------------------------------------------------------- Pages 14-26
Safety Instructions
1. Before getting started with the machine assembly, please read through this manual.
2. Separate all of the parts after opening the boxes and verify that all parts are accounted for and have no damage.
3. Assemble the machine on a solid level surface. This ensures the best possible performance, function, and safety for the Functional Smith Trainer and workouts.
Caution
: To avoid any injury it requires 2 persons at least to assemble this product!
Warning
It is essential that you consult with your physician before starting an exercise program.
It is very important that all warnings and instructions are read and followed before using this system.
Immediately replace any worn, torn, scratched warning labels or stickers.
It is necessary to inspect this product periodically to maintain safety and proper function.
Inspect this gym before each workout for loose or worn parts, especially the moving parts such as
the cables, pulleys and accessories,and connecting points.
Immediately replace any worn or defective parts and do not use this gym until it is repaired or replaced.
! Make sure all adjustment pins are fully engaged before using this gym.
! Keep minors and children from playing on or around this gym at all times. e gym and workout. onnections to
FLOOR PLAN DIAGRAM
74.83"
1901mm
The Complete Functional Smith Trainer has a layout dimension of 78" Length x 74.83" Width x 90.1" Height.
Page 3
PARTS LIST
# Part No.
Description
1 P04-3909 Top Cross Beam
2R P20-4564 Top Beam,Main Frame, Right
3L P20-4565 Top Beam, Main Frame, Left
4 P20-4498 Rear Top Frame Assembly
5 P20-4508 Rear Upright
6 P20-4510 Rear Bottom Frame Assembly
7 P02-6186 Bracket
8 P03-1847 Linear Bearing Shaft
9 P20-2664 Weight Holder
10 P20-2665 Weight Bar Assembly
11 P20-4522 Shaft Mount
12L P20-4500 Safety Bar Left
13R P20-4512 Safety Bar Right
14 P20-4501 Low Row Assembly
15 P20-4503 Cable Column Tube
16R P20-4504 Right Cable Column Slider
17L P20-4505 Left Cable Column Slider
18 P20-4506 Swivel Pulley Assembly
19 P20-0358 Top Weight Assembly
20 P20-2038 Pulley Bracket Assembly
21 P01-5286 Guide Rod
22 P04-0986 Weight Stack Riser
23 P10-0072 Weight Plates
24 P11-0057 Weight Selector Pin
25 P20-4499 Pull-Up Bar Assembly
26 P20-4511 Weight Shroud Mount
27 P10-1135 Placard
28 P20-4509 Lat Pull Swivel Pulley
29 P20-4507 Double Pulley Plate
30 P20-4502 Low Row Bar
31 P05-0289 Chain
32 P10-1196 Weight Stack Shroud
33 A05-0212 Guide Rod Cap
34 A06-0304 Weight Stack Bumper
35 P06-0051 Pulley
36 P13-0469 Upper Cable
37 P13-0470 Lower Cable
38 P13-0471 Row Cable
39 P12-0148 4 Ring D Handles
40 P12-0060 Ankle Strap
41 P12-0204 Pull Up Assist Strap
42 P12-0066 D Handle / Ab Strap
43 P20-4566 Base, Main Frame
44R P20-4567 Front Upright, Main Frame, R
45R P20-4569 Rear Upright, Main Frame, R
46L P20-4568 Front Upright, Main Frame, L
47L P20-4570 Rear Upright, Main Frame, L
Page 4
2
1
1
1
1
1
1
2
2
2
2
4
20
2
2
4
1
2
1
2
4
2
1
4
4
4
30
2
2
2
2
1
1
1
1
1
2
1
4
1
2
1
1
QTY
1
1
1
1
Parts Reference
*The Left or Right parts and the front or rear parts are determined by the user's in exercise.
Right
Rear
Front
Left
13R
92
16R
2R
44R
45R
43
25
4
28
10
6
1
29
20
19
3L
27
14
18
46L
17L
15
47L
43
11
5
7
26
8
9
21
23
32
12L
Page 5
HARDWARE LIST
66
67
68
69
62
63
64
65
70
71
72
73
#
51
57
58
59
60
61
52
54
55
56
Part Number Description
DAEE01401220NAB 1/4" x 1/2"L Button Head Screw
DAEE01420020NB
DA1E01243413NB
DA1E03850016NB
DA1E03843416NB
DA1E03831416NB
DA1E03823416NB
DA1E03821416YB
DA1E03820016NB
DA1E03813416YB
1/4" x 2"L Button Head Screw
1/2" x 4 3/4"L Hex Bolt
3/8" x 5"L Hex Bolt
3/8" x 4 3/4"L Hex Bolt
3/8" x 3 1/4"L Hex Bolt
3/8" x 2 3/4"L Hex Bolt
3/8" x 2 1/4"L Hex Bolt with blue patch
3/8" x 2"L Hex Bolt
3/8" x 2"L Hex Bolt with blue patch
DA1E03803416YB
DB1E01208013NU
DC126013020B
DC125010020B
DC325010020AB
DC116006510B
DB2E01212013B
DB2E03811000B
DB2E01405500B
DI1080080U
P08-0076B
P08-0139B
3/8" x 3/4"L Hex Bolt with blue patch
1/2" Jam Nut
1/2" Flat Washer
3/8" Flat Washer
Curved Washer
1/4" Flat Washer
1/2" Lock Nut
3/8" Lock Nut
1/4" Lock Nut
Snap Hook
1 1/2"H Step Spacer
1/2"H Step Spacer
Tools Required for Assembly
Standard Socket Set (including 1/2", 9/16" and 3/4" sockets)
1/2", 9/16" and 3/4" Wrenches or Adjustable Wrenches
M4 Allen Wrench for 5/16" Set Screws - Supplied
M5 Allen Wrench for 1/4" Button Head Screw - supplied
M8 Allen Wrench for Cap Head Screws - supplied
Tape Measure
Rubber Mallet
40
4
2
59
13
2
4
93
8
8
4
2
QTY
2
1
24
16
10
2
2
2
16
8
Page 6
Hardware Chart
Hex Bolt Button Head Screw
Flat Head Screw
Shoulder Bolt
Cap Head Screw
Phillip Head Screw
1/4” Flat Washer 3/8” Flat Washer 1/2” Flat Washer
Curved Washer 3/8” Lock Nut 1/2” Lock Nut
Step Spacer Barrel Spacer Snap Hook
Page 7
Components Pre-installed in the Parts
88
89
90
91
84
85
86
87
69
81
82
83
#
35
53
58
60
65
Part Number
P06-0051
DABE03801216YB
DA1E03823416NB
DA1E03820016NB
DC125010020B
Description
3 1/2" Pulley
3/8" x 1/2"L Cap Head Screw with BP
3/8" x 2 3/4"L Hex Bolt
3/8" x 2"L Hex Bolt
3/8" Flat Washer
DB2E03811000B 3/8" Lock Nut
DA0E03811216ANB 3/8" x 1 1/2"L Cap Head Screw
P10-0071
P10-0073
Top Weight
Selector Stem
P04-2153
P04-2608
P05-0999
DB2E51608518B
P03-1842
P08-0048
P08-0110
N/A
Floating Pulley Bracket
Weight Bar Weldment
Shoulder Bolt
5/16" Lock Nut
Spacer
Bushing
Barrel Spacer
N/A
96
97
98
99
92
93
94
95
P02-3859
P02-6180
DA1E03810016NB
A06-0530
P04-3910
P06-0589
P04-3908
A06-0529
100
101
102
103
P06-0225
P06-0358
P04-3915
P06-0278
104
105
P12-0247
P04-3924
106 P06-0042
107R P04-3922
Rear Weight Rack Plate
Front Weight Rack Plate
3/8" x 1"L Hex Bolt
2" x 4" Flatoval End Cap
Rear Top Frame Weldment
Guide Rod Collar
Pull Up Bar Weldment
40mm x 80mm Flatoval End Cap
2" Square End Cap
1 1/4" Round End Cap
Safety Bar Weldment
1" x 2" Rectangular End Cap
Anti-Skid Tape
Foot Plate Weldment
1 3/4" Square End Cap
Right FT Adjuster
120
121
122
123
116
117
118
119
124
125
126
127
128
129
108
109
A06-0528
P08-0061
110 P11-0179
111L P04-3920
112
113
114
115
P02-6191
P04-3918
P04-3974
P04-3930
DA0C014004720YB
P06-0191
P06-0011
P04-2607
P11-0232
P04-0614
P04-0613
DC120010510B
P01-5285
DC100019000B
P04-3972
P04-3973
P04-3975
P04-3976
Sleeve
Bushing
FT Adjustment Pin
Left FT Adjuster
Double Pulley Plate
Lat Pull Swivel Pulley Weldment
Base Weldment, Main Frame
Shaft Mount Weldment
1/4" x 3/16" Set Screw
Bumper
Round End Cap
Weight Holder Weldment
Adjustment Pin
Swivel Pulley Weldment
Swivel Pulley Holder
3/4" x 3/8" Flat Washer
Cable Column Tube
STW-19 External Snap Ring
Top Beam Weldment,Main Frame, Right
Top Beam Weldment,Main Frame, Left
Front Upright Weldment, Main Frame
Rear Upright Weldment, Main Frame
Page 8
Pre-installed Parts Reference-1
#19 P20-0358 Top Weight Assembly
82
81
83
#20 P20-2038 Pulley Bracket Assembly
35
69
60
84
65
#9 P20-2664 Weight Holder Assembly
119
117
118
116
#11 P20-4522 Shaft Mount
115
#12L P20-4500 Left Safety Bar
104
103
#13R P20-4512 Safety Bar Right
103
104
102
102
Page 9
Pre-installed Parts Reference-2
#28 P20-4509 Lat Pull Swivel Pulley
69
113
65
58
35
#18 P20-4506 Swivel Pulley Assembly
35
121
60
69
#29 P20-4507 Double Pulley Plate
112
35
65
60
120
122
60
69
65
#17L P20-4505 Left Cable Column Slider
109
108
111L
110
#16R P20-4504 Right Cable Column Slider
109
108
110
107R
Page
10
Pre-installed Parts Reference-3
#10 P20-2665 Weight Bar Assembly
87
86
89
90
85
123
88
123
#4 P20-4498 Rear Top Frame Assembly
97
#25 P20-4499 Pull-Up Bar Assembly
96
101
99
100
98
99
Page
11
Pre-installed Parts Reference-4
#2R P20-4564
Top Beam,Main Frame, Right
126
95
#3L P20-4565
Top Beam, Main Frame, Left
127
95
#43 P20-4566
Base, Main Frame
114
#44R P20-4567
Front Upright, Main Frame, R
99
94
93
65
128
65
69
128
95
#46L P20-4568
Front Upright, Main Frame, L
99
69
94
65
93
Page
12
Pre-installed Parts Reference-5
#45R P20-4569 Rear Upright, Main Frame, R
99
69
65
#47L P20-4570 Rear Upright, Main Frame, L
99
69
65
65
94
65
94
92
92
129
129
#14 P20-4501 Low Row Assembly
105
106
#15 P20-4503 Cable Column Upright
124
53
99
Page
13
ASSEMBLY Instructions
Assemble the machine on a solid level surface. This ensures the best possible performance, function, and safety for the Functional Smith Trainer and workouts.
*Set the Left and Right Main Frames in a position close to the Functional Smith Trainer's final position.
Caution
: To avoid any injury it requires 2 persons at least to assemble this product!
Page
14
ASSEMBLY STEPS
Hardware Required
# Description QTY
12
62
” x ”L Hex Bolt with blue patch
4
# Description
69
3/8" Lock Nut
Right Main Frame Assembly
2R
58
65
65
QTY
28
12
Left Main Frame Assembly
69
65
3L
69
58
44R
46L
47L
45R
58
62
65
62
65
65
69
65
43
43
1. Attach the Right Front Upright,Main Frame (#44R) to the Main Frame Base (#43) using:
#62 2- 3/8" x 3/4"L Hex Bolts with blue patch
#65 2- Flat Washers
2. Attach the Right Rear Upright, Main Frame (#45R) to the Main Frame Base (#43) as shown using:
#58 2- 3/8" x 2 3/4"L Hex Bolts
#65 4- Flat Washers
#69 2- 3/8" Lock Nuts
3. Attach the Right Top Beam, Main Frame (#2R) to the front and rear upright, Main Frame as shown using:
#58 4- 3/8" x 2 3/4"L Hex Bolts
#65 8- Flat Washers
#69 4- 3/8" Lock Nuts
After all the bolts are tightened, put the Right Main Frame Assembly against the wall or over the packaging box crosswise.
Repeat the above steps to complete the Left Main Frame Assembly.
Page
15
ASSEMBLY STEPS
*Set the Left and Right Main Frames in a position close to the Functional Smith Trainer's final position.
Hardware Required
# Description
55
3/8" x 5"L Hex Bolt
66
Curved Washer
69 3/8" Lock Nut
QTY
12
24
12
55
66
4
Right
Main Frame
66
69
1
6
Left
Main Frame
1. Attach the assembled Right Main Frame to the Rear Bottom Frame (#6) using:
#55 2- 3/8" x 5"L Hex Bolts
#66 4- Curved Washers
#69 2- 3/8" Lock Nuts
Repeat the above assembly step to complete the assembled Left Main Frame to the Rear Bottom Frame.
2. Attach the Rear Top Frame (#4) to the Left and Right Main Frames using:
#55 4- 3/8" x 5"L Hex Bolts
#66 8- Curved Washers
#69 4- 3/8" Lock Nuts
3. Attach the Top Cross Beam (#1) to the Left and Right Main Frames using:
#55 4- 3/8" x 5"L Hex Bolts
#66 8- Curved Washers
#69 4- 3/8" Lock Nuts
Page 16
ASSEMBLY STEPS
Hardware Required
# Description QTY # Description
4 66
3/8
” x 3 1/4”L Hex Bolt
3/8
” x 2”L Hex Bolt with blue patch
2
69
Curved Washer
1 3/8
” Flat Washer
25
*Pre-installed
61
65
125
57
65
28
55
69
35
QTY
8
4
5
66
69
5
55
1. Attach the Rear Upright (#5) to the Rear Top Frame and the Rear Bottom Frame using:
#55 4- 3/8" x 5"L Hex Bolts
#66 8- Curved Washers
#69 4- 3/8" Lock Nuts
2. Attach the Pull-Up Bar Assembly (#25) to the adjustment bracket of Top Cross Beam to the desired position using:
#57 1- 3/8" x 3 1/4"L Hex Bolt
#65 2- 3/8" Flat Washers
#69 1- 3/8" Lock Nut
3. Place the shaft of the Pull-Up Bar Assembly (#25) in between the Pulley Housings of Rear Top Frame as shown.
Install the Pulleys (#35) in the pulley housings of Rear Top Frame aligning the shaft of rear top frame and secure with:
#61 2- 3/8" x 2"L Hex Bolts with blue patch
#65 2- 3/8" Flat Washers
Page 17
ASSEMBLY STEPS
Hardware Required
# Description QTY
62
3/8
” x 3/4”L Hex Bolt with blue patch
8
65
3/8
” Flat Washer
8
9
13R
8
62
65
*Use M4 Allen Wrench to tighten set screws.
11
10
12L
1. Hook the Weight Bar Assembly (#10) onto the Front Racks to the desired postion.
2. Slide 1 Linear Bearing Shaft (#8) into one of the Weight Holder Assemblies (#9), the shaft faces foward as shown.
3. Place a Shaft Mount (#11) onto the Bottom of the Linear Bearing Shaft assuring it is fully seated and tighten the set screws.
4. Place a Shaft Mount onto the Top of the Linear Bearing Shaft before positioning it into the Right Main Frame.
5. Gently Guide the shaft of the Weight Holder Assembly into the Weight Bar Assembly all the way in.
6. Secure the top and bottom Shaft Mounts to the Right Main Frame using:
#62 4- 3/8" x 3/4"L Hex Bolt with blue patch
#65 4- 3/8" Flat Washers
7. Sit the rod groove of Right Safety Bar (#13R) onto the Front and Rear Weight Rack Plates attached to the Right Main Frame.
Repeat the above steps installing the second Linear Shaft and Weight Holder Assembly at the Left Main Frame.
Page
18
ASSEMBLY STEPS
Hardware Required
# Description
1/2
” x 4 3/4”L Hex Bolt
3/8
” x 2 3/4”L Hex Bolt
64 1/2
” Flat Washer
QTY # Description
2 65 3/8
” Flat Washer
8
4
68 1/2
” Lock Nut
69
3/8
” Lock Nut
58
65
54
64
18
64
68
120
16R
17L
110
15
15
69
QTY
16
2
8
1. Loosen the pre-installed #53 3/8" x 1/2"L Cap Head Screw at the upper end of Cable Column Upright (#15) with M8 Allen Wrench or slide the Right Cable Column Slider (#16R) onto one of the Cable Column Uprights (#15) from the lower end to the desired postion by pulling out the FT Adjustment Pin (#110) without loosening the pre-installed screw.
*Secure the #53 1- 3/8" x 1/2"L Cap Head Screw in the Cable Column Upright with M8 Allen Wrench after sliding the right cable cloumn slider from the upper end of the cable column upright.
2. Attach the Cable Column Upright to the Right Main Frame using:
#58 4- 3/8" x 2 3/4"L Hex Bolts
#65 8- 3/8" Flat Washers
#69 4- 3/8" Lock Nuts
3. Assemble one of FT Swivel Pulley Assemblies (#18) to the Right Cable Column Slider using:
#54 1- 1/2" x 4 3/4"L Hex Bolt
#64 2- 1/2" Flat Washers
#68 1- 1/2" Lock Nut
Repeat the above steps to install the Left Cable Column Slider (#17L) and one of FT Swivel Pulley Assemblies to the Left Main Frame.
Page 19
Foot Plate Assembly
ASSEMBLY STEPS
Hardware Required
# Description
62 3/8
” x 3/4”L Hex Bolt with blue patch
51 1/4
” x 1/2”L Button Head Screw
52 1/4
” x 2”L Button Head Screw
QTY # Description
1
2
2
65 3/8
” Flat Washer
67 1/4
” Flat Washer
70 1/4
” Lock Nut
* Use M5 Allen Wrench to tighten 1/4" Button Head Screws
52 27
51
52 serial number
14
QTY
1
4
4
67
70
7
67
70
62
67
70
65
67
70
#14 Low Row Assembly storage
1. Fasten the Placard Bracket (#7) to the Rear Upright using:
#62 1- 3/8" x 3/4"L Hex Bolt with blue patch
#65 1- 3/8" Flat Washer
2. Attach the Placard (#27) to the Placard Bracket using:
#51 2- 1/4" x 1/2" Button Head Screws
#67 2- 1/4" Flat Washers
#70 2- 1/4" Lock Nuts
3. Fasten the Placard to the Rear Upright using
#52 2- 1/4" x 2" Button Head Screws
#67 2- 1/4" Flat Washers
#70 2- 1/4" Lock Nuts
4. Insert the Low Row Assembly (#14) into the Rear Upright to the end as shown.
* Store up the Low Row Assembly as shown when not in use.
Page 20
ASSEMBLY STEPS
Hardware Required
# Description
56 3/8
” x 4 3/4”L Hex Bolt
QTY
4
59 3/8
” x 2 1/4”L Hex Bolt with blue patch
16
66 Curved Washer
65 3/8
” Flat Washer
69 3/8
” Lock Nut
63 1/2" Jam Nut
8
16
4
2
Important:
For Safety,
Top Weight Pulley Assemblies must be fully threaded into the
Top Weight Assembly with the
Jam Nuts tightened securly
26
65
33
59
*If optional 200lb weight plates is being assembled, store away the Weight Stack Risers (#22)
21
66
69
20
1. Attach 1 Weight Shroud Mount (#26) to the right side of rear bottom frame as shown using:
#59 4- 3/8" x 2 1/4"L Hex Bolts with blue patch
#65 4- 3/8" Flat Washers
2. Place 2 Weight Stack Risers (#22) aligning onto the the holes of rear bottom frame as shown.
Place 1 Weight Stack Bumper (#34) onto each
Weight Stack Riser.
56
19
23
34
24
3. Slide the Guide Rods (#21) through each weight stack
bumper and weight stack riser into the rear bottom frame.
4. Carefully Slide 15 Weight Plates (#23) down the Guide Rods onto the Weight Stack Bumpers.
Be sure that all weight plates are facing toward fron of the machine.
Front of weight plate is indicated by recessed area for weight stack numbers.
Then slide the Top Weight Assembly (#19) down the Guide Rods onto
Weight Stack
22
5. Completely thread the bolt of the Top Weight Pulley Assembly (#20) and a Jam Nut (63) in the Top Weight Assembly with a Locknut on the Pulley Bolt facing towards the front of the gym.
6. Place the other 1 Weight Shroud Mount through the Guide Rods, and then loosen the set screws attached to the
the Guide Rod Collars (#33) sliding the collar onto each Guide Rod.
7. Insert the Guide Rods into the holes of rear top frame and then lift the Guide Rods up.
Put #56 2- 3/8" x 4 3/4"L Hex Bolts with #66 4- Cruved Washers through the rear bottom frame and then secure the bolts with #69 2- 3/8" Lock Nuts
8. Slide the Guide Rod Collars (#33) to the top end of the Guide Rods against the rear top frame.
Tighten down the attached set screws to the guide rod collars with M4 Allen Wrench.
9. Position the Weight Shroud Mount (#26) against the rear top frame as shown using:
#59 4- 3/8" x 2 1/4"L Hex Bolts with blue patch
#65 4- 3/8" Flat Washers
10. Insert the Weight Selector Pin (#24) into one of the holes of the Weight Stack.
Repeat the above steps to install the weight stack at the left side of rear top frame and rear bottom frame.
Page 21
ASSEMBLY STEPS
Hardware Required
# Description
56 3/8
” x 4 ”L Hex Bolt
58
3/8
” x 2 ”L Hex Bolt
60 3/8” x 2
”L Hex Bolt
72 1 1/2"H Step Spacer
QTY # Description
4
4
10
73
1/2"H Step Spacer
65 3/8” Flat Washer
69 3/8
” Lock Nut
8
69
69
65
56
72
35
56
65
72
72
69
60
QTY
8
20
18
72
69
The Pulley is installed after the Row Cable installation completed.
60
65
The Pulley is installed after the Row Cable installation completed.
58
73
73
69
35
65
69
58
73
73
69
*After the Pulleys are installed in the Right side of Rear Top Beam and Rear Bottom Frame, install the Pulleys with the same hardware on the left side of rear top beam and rear bottom frame.
Page 22
ASSEMBLY STEPS
* Before installing the cable unlock the bolt removing the Snap Hook and the
U bracket and sliding off the Stop Ball.
After the Cable installation is completed, slide the stop ball onto the cable, next attach the U bracket to the cable end and insert the bolt through the U bracket and the snap hook.
Tighten the bolt with a Jam Nut.
snap hook
U Bracket stop Ball
*Repeat the Cable installation on the right side of Rear Frame
After both cables are installed, press down the spring clip of the Snap Hook and hook in the 4 Ring D Handles (#39)
39
#36 P13-0469 Upper Cable
8765mm
Start the cable routing by fully threading the bolt of the cable into the Left Cable Column
Slider.
ASSEMBLY STEPS
* Before installing the cable unlock the bolt removing the Snap Hook and the
U bracket and sliding off the Stop Ball.
After the Cable installation is completed, slide the stop ball onto the cable, next attach the U bracket to the cable end and insert the bolt through the U bracket and the snap hook.
Tighten the bolt with a Jam Nut.
snap hook
U Bracket stop Ball
*Repeat the Cable installation on the left side of Rear Frame
42
After both cables are installed, press down the spring clip of the Snap Hook and hook in the D Handle / Ab Straps (#42)
#37 P13-0470 Lower Cable
5235mm see page 21
Go inside the tube see page 21
Start the cable routing by fully threading the bolt of the cable into the Main Frame.
ASSEMBLY STEPS
* Before installing the cable unlock the bolt removing the Snap Hook and the
U bracket and sliding off the Stop Ball.
After the Cable installation is completed, slide the stop ball onto the cable, next attach the U bracket to the cable end and insert the bolt through the U bracket and the snap hook.
Tighten the bolt with a Jam Nut.
stop ball snap hook
U Bracket
*Repeat the Cable installation in the left side of Rear Bottom Frame
After both cables are installed, press down the spring clip of the Snap Hooks and hook in the Low Row Bar (#30).
#38 P13-0471 Row Cable
3535mm
Start the cable routing by fully threading the bolt of the cable into the rear bottom frame.
ASSEMBLY STEPS
32
Attach the Weight Stack Shrouds (#32) to the Weight Shroud Mounts as shown.
Assembly for the PRSF-15 is complete.
Page 26
32
