CD PLAYER WITH TURNTABLE AND STEREO RADIO

CD PLAYER WITH TURNTABLE AND STEREO RADIO
CD PLAYER WITH TURNTABLE AND
STEREO RADIO
MODEL 9282
INSTRUCTION MANUAL
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions
2. Keep these instructions
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with these instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10. Only use attachments / accessories specified by the manufacturer.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
13. This appliance shall not be exposed to dripping or splashing water and no object filled with
liquids such as vases shall be placed on the apparatus.
14. Do not overload wall outlet. Use only power source as indicated.
15. Do not attempt to dismantle, open or repair this product yourself. If a problem
occurs, seek advice from your local qualified service technician or contact the
distributor at the telephone number at the back of this instruction manual.
16. Caution marking and nameplate are located on back of product.
-1-
PRECAUTION BEFORE USE
•
•
•
UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
DO NOT CONNECT THE UNIT TO AN AC OUTLET BEFORE CHECKING THE OUTLET’S
VOLTAGE AND ALL OTHER CONNECTIONS HAVE BEEN MADE.
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL
INCHES AROUND THE UNIT FOR VENTILATION.
CAUTION:
USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT
QUALIFIED SERVICE PERSONNEL.
IMPORTANT NOTES
Avoid installing the unit in locations described below:
•
Places exposed to direct sunlight or close to heat radiating appliances such as
electric heaters.
•
•
Places subject to constant vibration.
Dusty, humid or moist places.
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber 'feet' to prevent the product from moving when you
operate the controls. These 'feet' are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain types of oil
based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your
furniture we strongly recommend that you purchase small self-adhesive felt pads, available at
hardware stores and home improvement centers everywhere, and apply these pads to the bottom
of the rubber 'feet' before you place the product on fine wooden furniture.
-2-
Location of controls
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
27)
28)
Dust cover
CD play/pause
button
CD stop button
CD skip up /down button
Rep/Ran button
Program button
Volume up/down button
Power button
CD tray
CD tray open button
3.5mm stereo headphone jack
Function selector
Radio band selector
Power LED indicator
LCD display
FM stereo LED indicator
Dial scale
Tuning knob
Tape forward / Eject button
Cassette door cover
Spindle adaptor
Turntable speed selector
Tone arm rest
Line out socket
Speaker jack
FM antenna
Auto stop on/off switch
AC line cord
Caution:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
This unit should not be adjusted or repaired by anyone except qualified service personnel.
Precautions for use
Installation
•
•
•
Unpack all parts and remove protective material.
Do not connect the unit to AC outlet before checking the AC voltage and before all other connections have been
made.
Do not cover any vents and make sure that there is a space of several inches around the unit for ventilation.
-3-
Connection
1.
2.
3.
Connect the power cord to AC outlet.
Connect the speaker wire to the speaker jack (25) located on the rear side of unit.
Press the power button(8) and the power LED indicator(14) will light up which means the power supply is normal.
Now your system is ready to play the music.
Listening to radio
Manual tuning
1.
2.
3.
4.
Select the function selector(12) to “ Tuner “ position.
Select the desired band with radio band selector(13) (AM or FM or FM-Stereo).
Tune to the required station by turning the tuning knob(18).
Adjust volume up/down(7) to the desired volume level.
FM & FM-Stereo reception
z
z
Set the radio band selector(13) to “ FM ” position. Programs are received in mono mode. When stereo signals are
weak, it is preferable to receive the program in mono.
Set the radio band selector(13) to “FM-St” position to receive stereo programs. The FM-Stereo LED indicator(16)
will light up to show FM stereo program is being received.
Hints for best reception:-
AM : the receiver has a built-in AM bar antenna. If AM reception is weak, slightly rotating or re-positioning of the
unit will usually improve the AM reception.
FM : the receiver has a built-in FM wire antenna(26) hanging at the rear cabinet. This wire should be completely
unraveled and extended for best reception.
Playing compact discs
z
Getting started
1.
Set the function selector(12) to “CD ” position then open the CD tray by pressing the CD tray open button(10). Put
a CD disc into the compartment and close the CD tray.
Focus search is performing if disc is inside. Total number of tracks will appear on LCD display(15).
Adjust volume up/down(7) to the desired volume level.
-4-
2.
3.
z
Play / pause mode
1.
Press play/pause button(2) to start to play. The first track will be played and the playing track will show on the LCD
display(15).
If play/pause button(2) was pressed during play mode, go to pause mode and the track number will be flashing.
2.
z
Stop mode
1.
If stop button(3) is pressed during play or pause mode, go to stop mode and the total number of tracks will be
displayed.
z
Skip mode (skip up
1.
2.
3.
During play or pause mode, if skip up button(4) was pressed it will go to next track and display the track number.
During play or pause mode, if skip down button(4) was pressed it will go back to the beginning of the track and the
same track number is displayed.
Press skip down button(4) again to go to the previous track.
/skip down
)
z
Repeat/random mode
Press the rep/ran button(5) before or during play. A single track repeat or all tracks repeat and random mode can be
selected. Each press will switch the mode as follows:
(1) Repeat 1
z
(2) repeat all
(3) random
(4) repeat off
Program mode
Up to 20 tacks can be programmed for disc playing. Be sure to press the stop button(3) before programming.
1. Set in CD mode.
2. Press the program button(6) and the “ PROG ” icon will flash on display.
3. Select a desired track by using the skip up/down buttons(4).
4. Press the program button(6) to enter the track into the memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if desired.
6. When all the desired tracks have been programmed, press play/pause button(2) to play the disc in the order you
have programmed. The program icon will light up during playback
7. Press stop button(3) to terminate program play.
Listing to tape
General operation
Select the function selector(12) to “ Tape “ position.
Cassette playback
: the system will start the playback automatically after inserting
a cassette tape
Stop and eject
: press the “tape forward/eject“ button (20) completely inward
and the cassette tape will be ejected though the cassette door cover (21). (See
diagram below for button position to eject tape.)
Fast forward
: press the “tape forward/eject“ button (19) halfway inward during
Playback mode to fast forward the tape. (See diagram below for button position
(middle) to fast forward.)
slightly press the “tape forward/eject “ button (19) again to resume normal playback.
(See diagram below for button position (highest) to play.)
NOTE:
-
Make sure the direction is correct when inserting the tape into the system.
-
During fast forward, some “searching” noise will be heard as the system is not performing its normal playback
function during fast forward mode.
It is recommended to take out the cassette tape from the system after listening. Do not leave the cassette tape
inside the system when not in use.
-
-5-
Phono
NOTE:
-
Remove the stylus (needle) protector.
Securing the tone arm to the arm rest there is a little clip. Be sure to raise the clip
from the tone arm before playing. When not playing, snap the clip back over the
tone arm to keep it secure.
1.
2.
3.
4.
Select the function selector(12) to “ Phono “ position.
Set the speed selector(22) to the proper position depending on the record to be played.
Place the record on the platter (turntable). Use the spindle adaptor(22) if necessary.
Lift the tone arm from the rest(23) and slowly move toward the record. The platter will start to
rotate.
Place the tone arm at the desired position of the record.
Adjust volume up/down(7) to the desired volume level.
At the end of record, the platter will automatically stop rotating. Lift the tone arm from the
record and return it to the rest.
To stop manually, lift the tone arm from the record and return it to the rest.
5.
6.
7.
8.
NOTE: Some records are out of the auto-stop area setting and the turntable will stop before the last song finishes
playing. In this case, select the auto-stop switch (27) to “ off “ position, then it will run to the end of the record but will
not stop automatically. You will need to stop the turntable by pressing the power button or change the auto-stop switch
back to “on” position. Then put back the tone arm back to the rest position.
CARE AND MAINTENANCE
1.
2.
3.
Avoid operating your unit under direct sunlight or in hot, humid or dusty places.
Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
Unplug the unit from the electrical power outlet immediately in case of malfunction.
CLEANING THE UNIT
z
To prevent fire or shock hazard, disconnect your unit from the AC power source when
cleaning.
z
The finish on the unit may be cleaned with a dust cloth and cared for as other furniture, Use
caution when cleaning and wiping the plastic parts.
z
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or polish
sprays on the cabinet.
z
If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft
cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or
polishes as these will damage the finish of your unit.
CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.
-6-
TROUBLE SHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
SOLUTION
• The unit is disconnected from the
AC outlet
The unit will not
play
Unit is ON but
there is low or
• Connect to an outlet.
• The AC outlet has no power
• Try the unit in another outlet
• The volume Control has been
• Turn the Volume control to a higher
no volume
turned all the way down
position
SPECIFICATIONS
Power requirement:
Main Unit
AC 120V ~ 60Hz
8W
*The specifications and external appearance of the set are subject to change without prior
notice.*
-7-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement