Commell LV-675 User's Manual
The Commell LV-675 is a Mini-ITX motherboard that supports Intel Pentium M processors, DDR200/266/333MHz memory, and features integrated graphics, High Definition Audio, and Gigabit LAN. With its compact size and powerful performance, it is ideal for building small form-factor systems for various applications such as industrial automation, digital signage, and home theater PCs.
Advertisement
Advertisement
LV-675
Mini-ITX Motherboard
User’s Manual
Edition 1.0
2005/11/30
LV-675 User’s Manual
Copyright
Copyright 2005, all rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products.
This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw
2
LV-675 User’s Manual
Packing List:
Please check the package content before you starting using the board.
Hardware:
LV-675 motherboard x 1
Cable Kit:
26-pin Slim Type Floppy Cable x 1
44-pin ATA33 IDE Cable x 1
40-pin ATA100 IDE Cable x 1
COM port Cable x 1
DVI output cable kit (LV-675D only)
I/O Shield x 1
Printed Matters:
User’s Manual x 1
Driver CD x 1
CPU Cooler x 1
3
LV-675 User’s Manual
Index
Chapter 1 <Introduction> ................................................................................ 7
1.1 <Product Overview>............................................................................ 7
1.2 <Product Specification> ...................................................................... 8
1.3 <Mechanical Drawing>...................................................................... 10
1.4 <Block Diagram>............................................................................... 11
Chapter 2 <Hardware Setup>........................................................................ 13
2.1 <Connector Location>....................................................................... 13
2.2 <Jumper Location & Reference> ...................................................... 14
2.3 <Connector Reference>.................................................................... 15
2.3.1 <Internal Connectors> ........................................................... 15
2.3.2 <External Connectors>.......................................................... 15
2.4 <CPU and Memory Setup> ............................................................... 16
2.4.1 <CPU Setup> ........................................................................ 16
2.4.2 <Memory Setup> ................................................................... 17
2.5 <CMOS Setup> ................................................................................. 18
2.6 <IDE Interface > ................................................................................ 18
2.7 <Enhanced IDE Interface>……………………………………………...20
2.8 <Floppy Port>....................................................................................21
2.9 <Ethernet Interface>……………………………………………………..22
2.10 <Onboard Display Interface> .......................................................... 23
2.10.1 <Analog Display> ................................................................ 23
2.10.2 <LVDS Display LV-675X Only> ........................................... 24
2.10.3 <DVI Display LV-675D Only>...............................................28
2.10.4 <S-Video Interface>……………………………………………29
4
2.11 <Integrated Audio Interface> ........................................................... 30
2.12 <GPIO Interface> ............................................................................ 32
2.13 <Power Supply> .............................................................................. 33
2.13.1 <Power Input> ..................................................................... 33
2.14 <Switch and Indicator>.................................................................... 34
LV-675 User’s Manual
Chapter 3 <System Setup> ........................................................................... 35
3.1 <Video Memory Setup> .................................................................... 35
Chapter 4 <BIOS Setup> ............................................................................... 36
Appendix A <I/O Port Pin Assignment>....................................................... 38
A.1 <IDE Port> ........................................................................................ 38
A.2 <Floppy Port> ................................................................................... 40
A.3 <IrDA Port> ....................................................................................... 40
A.4 <Serial Port>..................................................................................... 41
A.5 <VGA Port>....................................................................................... 41
A.6 <LAN Port> ....................................................................................... 41
A.7 < USB Interface > ............................................................................. 42
A.8 < LPT Port >………………………………………………………………42
Appendix B <Flash BIOS>……………………………………………………….43
B.1 <Flash Tool> ..................................................................................... 43
B.2 <Flash BIOS Procedure> ................................................................. 43
Appendix C <System Resources>………………………………… ..
44
C.1<I/O Port Address Map>…………………………………………………44
C.2<Memory Address Map>………………………………………………..46
C.3<System IRQ & DMA Resources>……………………………………..47
Appendix D <Display Setting>………………………………….…...
49
Appendix E
<
How to choose RS-422&RS-485
>………………………...
51
Appendix F<Programming Watch dog Timer>……………………………….52
Contact Information....................................................................................... 53
5
LV-675 User’s Manual
(This Page is Left for Blank)
6
LV-675 User’s Manual
Chapter 1 <Introduction>
1.1 <Product Overview>
LV-675 is the new generation of the Mini-ITX motherboard, with supporting last Intel
Pentium M processors for 533/400MHz front side bus, Intel 845GV and ICH4 chipset, integrated graphics, DDR200/266/333 memory, REALTEK ALC 655 High Definition
Audio, and one Intel 82541PI Gigabit LAN.
New Intel Pentium M Processor
The board supports last Intel Pentium M processors with 400/533MHz front side bus, to provide more powerful performance than before.
New features for Intel 845GV chipset
The board integrates Intel 845GV and ICH4 chipset, to provide new generation of the mobile solution, supports Intel graphics, DDR 200/266/333MHz memory, High Definition
Audio with 5.1 channels surrounding sound.
All in One multimedia solution
Based on Intel 845GV and ICH4 chipset, the board provides high performance onboard graphics, 18/24-bit dual channel LVDS interface(LV-675X only),DVI interface(LV-675D only), S-Video, TV-out and REALTEK ALC 655 5.1 channels High Definition Audio, to meet the very requirement of the multimedia application.
Flexible Extension Interface
The board provides one PCI-slot for graphics card, it also can support PCI-slot for LAN card or other devices. The board also provides two mini-PCI socket.
7
LV-675 User’s Manual
1.2 <Product Specification>
General Specification
Form Factor Mini-ITX motherboard
CPU Intel® Pentium M / Celeron M processors
Package type: FC-PGA478
Front side bus: 400/533MHz
( The Intel® Celeron® M Processor 4xx series have been designed to work with the Mobile Intel® 945 Express Chipset
Family only .)
Memory 1 x 184-pin DDR 200/266/333MHz SDRAM up to 1GB
Unbufferred, none-ECC memory supported only
Chipset Intel® 845GV (Northbridge) and ICH4 (Southbridge)
BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Green Function
Watchdog Timer
Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
System reset programmable watchdog timer with 1 ~ 255 sec./min. of timeout value
Real Time Clock
Enhanced IDE
Intel® ICH4 built-in RTC with lithium battery
UltraDMA100 40-pin IDE interface supports up to 2 ATAPI devices
One 44-pin IDE port onboard
Multi-I/O Port
Chipset Intel® ICH4 with Winbond® W83627HF controller
Serial Port 1x RS232 Port,1x RS232/422/485 Port
USB Port Four Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
Parallel Port
Floppy Port
One external bi-direction parallel port with SPP/ECP/EPP mode
One slim type Floppy port
IrDA Port
K/B & Mouse
GPIO
One IrDA compliant Infrared interface supports SIR
External PS/2 keyboard and mouse ports on rear I/O panel
One 12-pin Digital I/O connector with 8-bit programmable I/O interface
VGA Display Interface
8
Chipset Intel® 845GV GMCH (Graphic Memory Controller Hub)
Frame Buffer Up to 64MB shared with system memory
Display Type
Connector
CRT, LCD monitor with analog display
Onboard 18/24-bit dual channel LVDS interface (LV-675X Only)
Onboard DVI interface(LV-675D Only)
External DB15 female connector on rear I/O panel
Onboard 40-pin LVDS connector(LV-675X Only)
Onboard 26-pin DVI Connector (LV-675D Only)
TV-Out interface
Chipset
TV Mode
Intel 845GV GMCH built-in Intel Extreme Graphics with
Chrontel CH7009/CH7017 TV-out encoder
Support both of NTSC and PAL mode
LV-675 User’s Manual
Connector
Ethernet Interface
External S-video and RCA Jack on rear I/O panel
Controller
Type
Connector
Audio Interface
Intel 82541PI Gigabit Ethernet controller
Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
One External RJ45 connectors with LED on rear I/O panel
Chipset
Interface
Connector
Intel ICH4 with REALTEK ALC655 AC97 3D audio codec
5.1 channel 3D audio with front (R/L), rear (R/L), center and bass
SPDIF digital audio encoding signal input and output
Line-in, line-out, CD-in and Mic-in
External three phone jack for 5.1 channel audio on rear panel
External SPDIF connector on rear panel
Internal 10-pin header for line-in/-out, Mic-out, 4-pin header for CD-in
Expansive Interface
PCI One onboard standard PCI Slot(32-bit,33MHz)
Two Mini-PCI socket for TYPE III (32-bit, 33MHz)
Power supply: +3.3V, +5V
Power and Environment
Power
Requirement
Dimension
Temperature
Standard ATX Power Supply
170 (L) x 170 (H) mm
Operating within 0 ~ 60P o
C (32 ~ 140P o
F)
Storage within -20 ~ 85P o
C (-4 ~ 185P o
F)
Ordering Code
LV-675X
LV-675D
MP-878D
MP-541D
MP-541D2
Intel Pentium M Mini-ITX motherboard with onboard VGA, 1 x Gigabit
LAN, 4 x USB 2.0 Ports, Audio, 1 x RS232, 1 x RS232/422/485,
LVDS, S-Video,1x PCI slot, 2 x Mini-PCI, 1 x Parallel Port, 1x SPDIF
Intel Pentium M Mini-ITX motherboard with onboard VGA, 1 x Gigabit
LAN, 4 x USB 2.0 Ports, Audio, 1 x RS232, 1 x RS/232/422/485 , DVI,
S-Video,1x PCI slot, 2 x Mini-PCI, 1 x Parallel Port, 1x SPDIF
Mini-PCI Capture Card
Mini-PCI with one Giga Ethernet With Intel 82541PI PCI Connector
Mini-PCI with two Giga Ethernet With Intel 82541PI PCI Connector
The specifications may be different as the actual production.
For further product information please visit the website at TU http://www.commell.com.twUT
9
LV-675 User’s Manual
1.3 <Mechanical Drawing>
10
LV-675 User’s Manual
1.4 <Block Diagram>
Intel Pentium M/Celeron M Processors
Intel GMA Graphics
LVDS/DVI
TV-OUT
CH7107
CH7009
845GV
1 x 184-pin DDR
266/333MHz up to
1GB
UltraDMA100 IDE
4 x USB2.0 ports
REALTEK ALC 655
1 x LPT Port
2 x Serial ports
1 x Floppy ports
8-bit GPIO
ICH4
IrDA
BIOS
PCI
Intel 82541PI
Gigabit LAN
Mini-PCI slot x 2
PCI slot x 1
Agere FW323
IEEE 1394 x 1
11
LV-675 User’s Manual
(This Page is Left for Blank)
12
LV-675 User’s Manual
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_IR CN_COM2 JCSEL1 JRTC JCSEL2 SYSFAN
CPUFAN
JFRNT
JDOM
CN_USB1
IDE2
FDD
IDE1
PCI Slot
CN_DIO
ATX
CN_INV
(LV-675X Only)
JVLCD
(LV-675X Only
CN_LVDS
(LV-675X Only)
CN_DVI
JLAN
(LV-675D Only) Mini PCI 1
CN_COM1
AUDIO
LPT
KB / MS
Mini PCI 2
CN_AUDIO
CDIN
S-Video TV-Out VGA USB_RJ45 1394 SPDIF
13
LV-675 User’s Manual
2.2 <Jumper Location & Reference>
Jumper Function
JRTC
JVLCD
CMOS Operating/Clear Setting
Panel Voltage Setting (LV-675X Only)
JLAN
JDOM
Enable/Disable on Board LAN function
IDE1 Pin-20 voltage setting
JRTC
JDOM
14
JVLCD
JLAN
LV-675 User’s Manual
2.3 <Connector Reference>
2.3.1 <Internal Connectors>
Connector
CPU
DIMM
IDE1
IDE2
FDD
ATX
Function
Socket478 for Intel Pentium M/Celeron M CPU
184-pin DDR SDRAM DIMM socket
40-pin IDE connector
44-pin IDE connector
26-pin slim type floppy connector
24-pin ATX power input connector
CN_AUDIO 5 x 2-pin audio connector
CDIN 4-pin CD-ROM audio input connector
CN_DIO
CN_USB
6 x 2-pin digital I/O connector
5 x 2-pin USB connector
CPUFAN
SYSFAN
CN_LVDS
CN_INV
3-pin CPU cooler fan connector
3-pin system cooler fan connector
20 x 2-pin LVDS connector(LV-675X Only)
5-pin LCD inverter connector(LV-675X Only)
CN_IR 5-pin IrDA connector
CN_COM1/2 5 x 2-pin COM1 & COM2 connector
JFRNT
Mini-PCI
CN_DVI
14-pin front panel switch/indicator connector
2 x Mini-PCI socket
26-Pin connector(LV-675D Only)
2.3.2 <External Connectors>
Connector
USB_RJ45
VGA
KB
MS
Function
Dual USB and one RJ45 LAN connector
DB15 analog VGA connector
PS/2 keyboard connector
PS/2 mouse connector
SPDIF
S-Video
TV-Out
1394
LPT
SPDIF digital audio output connector
S-video connector on rear I/O panel
RCA Jack on rear I/O panel
One IEEE1394 connector on rear I/O panel
One parallel port on rear I/O panel
Remark
Standard
Standard
Standard
Slim
Slim
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Remark
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
15
LV-675 User’s Manual
2.4 <CPU and Memory Setup>
2.4.1 <CPU Setup>
The board comes with the socket478 for Intel Pentium M/Celeron M processors, it supports new generation of Intel Pentium M processors with 400/533MHz of front side bus . Please follow the instruction to install the CPU properly.
1. Use the flat-type screw drive to unlock the CPU socket
3. Lock the socket
Unlock way
Check point
2. Follow the pin direction to install the processor on the socket
16
LV-675 User’s Manual
2.4.2 <Memory Setup>
The board provides one 184-pin DDR DIMM to support DDR 200/266/333 memory modules up to 1GB of capacity. Non-ECC, unbuffered memory is supported only.
DDR
104-pin 80-pin
Please check the pin number to match the socket side well before installing memory module.
17
LV-675 User’s Manual
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
2-3
Default setting
Normal Operation
JRTC
1 3
18
LV-675 User’s Manual
2.6 <IDE Interface>
The board has one UltraDMA100 IDE1 interface to support up to 2 ATAPI devices .
The board has one UltraDMA33 IDE2 interface to support up to 2 ATAPI devices .
40
2
39
1
IDE1
44
2
43
IDE2
1
19
LV-675 User’s Manual
2.7 < Enhanced IDE Interface >
The Intel® ICH4 (south bridge chip) supports one enhanced IDE interface, dual channel for two ATAPI devices with ATA100. Based on this function, LV-675 has one 40-pin IDE connector with jumper selectable for pin-20 +5V supported. The jumper JDOM is two-pin type for pin-20 supplied with +5V to apply the DOM (Disk on Module).
JDOM
Jumper: JDOM
Type: onboard 2-pin header
JDOM Mode
ON
OFF
Default setting
IDE1 pin-20 5V power supply enable
No 5V power supply on IDE1 pin-20
20
LV-675 User’s Manual
2.8 <Floppy Port>
The board provides one slim type floppy port.
FDD
Floppy rear side
4. Lift up the brown plastic bar
5. Slot the cable in (Blue paste for brown bar side)
6. Press back the plastic bar
1. Lift up this plastic bar
2. Slot the cable in (Blue paste for outside)
3. Press back the plastic bar
21
LV-675 User’s Manual
2.9 <Ethernet Interface>
LV-675 integrates one Gigabit LAN interfaces with Intel 82541PI; it provide a standard
IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX and 10BASE-T applications. LV-675 provides one RJ45 connectors on the rear I/O panel. The JLAN can let you set to enable/disable the onboard LAN function.
JLAN
Enable
Jump Setting
1-2 (Default)
Disable 2-3
JLAN
RJ45 LAN connector
22
LV-675 User’s Manual
2.10 <Onboard Display Interface>
Based on Intel 845GV chipset with built-in graphics, the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS interface with 5-pin LCD backlight inverter connector(LV-675X Only).
Notice: When you install any PCI Graphic card, the onboard graphics would be disabled automatically.
2.10.1 <Analog Display>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard
DB15 female connector on rear I/O port.
VGA
23
LV-675 User’s Manual
2.10.2 <LVDS Display LV-675X Only >
The board provides one 40-pin LVDS connector for 18/24-bit dual channel panels, supports up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting.
24
1
5
CN_INV
39 40
1
3
JVLCD
1 2
CN_LVDS
LV-675 User’s Manual
Connector: CN_INV Connector:
Type: 5-pin LVDS Power Header Type: 3-pin Power select Header
Pin Description Pin Description
1
+12V
1
2
3
4
GND
GND
GND
5
ENABKL
Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector
Connector model: HIROSE DF13-40DP-1.25V
2
3
VCC (5V)
VCC/LDC
VCC3 (3.3)
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC
4 GND 3 GND
6 ATX0-
8 ATX0+
10 GND
12 ATX1-
14 ATX1+
16 GND
5 BTX0-
7 BTX0+
9 GND
11 BTX1-
13 BTX1+
15 GND
18 ATX2-
20 ATX2+
22 GND
24 ACLK-
26 ACLK+
28 GND
30 ATX3-
32 ATX3+
34 GND
36 N/C
38 N/C
40 N/C
17 BTX2-
19 BTX2+
21 GND
23 BTX3-
25 BTX3+
27 GND
29 BCLK-
31 BCLK+
33 GND
35 N/C
37 N/C
39 N/C
25
LV-675 User’s Manual
To setup the LCD, you need the component below:
1. A panel with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
LCD Installation Guide:
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. You would need a LVDS type cable.
Panel side
For sample illustrator only
4. To connect all of the devices well.
Board side
26
LV-675 User’s Manual
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
NO.
1
BIOS panel type selection form
Single channel Dual channel
Output format NO. Output format
2
3
800 x 600 (18bit)
1024 x 768 (18bit)
1024 x 768 (24bit)
4
5
1280 x 1024 (24bit)
1366 x 768 (24bit)
27
LV-675 User’s Manual
2.10.3 <DVI Display LV-675D Only >
The board provides optional DVI-D interface with Intel 845GV, compliant with DVI 1.0 standard.
Connector: CN_DVI
Connector type: 26-pin header connector (pitch = 2.54mm)
Pin Number Assignment Pin Number Assignment
1 TX1+ 2 TX1-
3 Ground 4 Ground
5 TXC+ 6 TXC-
7 Ground 8 PVDD
9 N/C 10 N/C
11 TX2+ 12 TX2-
13 Ground 14 Ground
15 TX0+ 16 TX0-
19 DDCDATA 20 DDCCLK
21 GND 22 N/C
23 N/C 24 N/C
25 N/C 26 N/C
28
39
40 CN_DVI
1
2
LV-675 User’s Manual
12.10.4 <S-Video Interface>
The board provides one S-Video interface up to 1024 x 768 resolution by NTSC/PAL supported, for three output types with Composite, S-Video and Component .
Notice1: This connector is for both S-Video/Composite outputs; please use attached two cables in the package for SDTV devices.
Notice2: S-Video and Composite can not be used at the same time.
S-Video TV-Out
29
LV-675 User’s Manual
2.11 <Integrated Audio Interface>
LV-675 integrated with REALTEK® ALC655 Codec for 5.1 channel sound output. It supports 16-bit stereo full-duplex with 48 KHz sampling rate, compliant with AC97
Rev.2.3 specifications.
The board has one phone jack on rear I/O panel for Line-out, Line-in, MIC(stereo)-in as
2-channel sound system, and Front, Rear, Center as 5.1-channel sound system. It also has one 10-pin header for additional audio output, the cable with phone jack is optional available.
For advanced configuration with system, please check the chapter of audio configuration.
30
MIC IN
Line IN
Line Out
Rear I/O phone jacks
1
CDIN
4
9
10
1
CN_AUDIO
2
LV-675 User’s Manual
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header
Pin Description Pin Description
1
3
Line in _L
Line in _R
5 MIC2
7 N/C
9 Front_R
2
4
Ground
MIC1
6 Ground
8 Front_L
Connector: CDIN
Type: 4-pin header (pitch = 2.54mm)
Pin Description
1 CD – Left
2 Ground
3 Ground
4 CD – Right
31
LV-675 User’s Manual
2.12 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO
Type: 12-pin (6 x 2) 2.0mm pitch header
Pin Description
1 Ground
3 GP0
5 GP1
7 GP2
9 GP3
11 VCC
Pin Description
2 Ground
4 GP4
6 GP5
8 GP6
12 +12V
1 2
11
CN_DIO
12
32
LV-675 User’s Manual
2.13 <Power Supply>
2.13.1 <Power Input>
The LV-675 provides a standard ATX power supply with 24-pin ATX connector .
12 24
ATX
1 13
Connector: ATX
Type: 24-pin ATX power connector
PIN assignment
1 3.3V
2 3.3V
3 GND
4 5V
5 GND
6 5V
7 GND
8 PW_OK
9 5V_SB
10 12V
11 12V
12 3.3V
13 3.3V
14 -12V
15 GND
16 PS_ON
17 GND
18 GND
19 GND
20 -5V
21 5V
22 5V
23 5V
24 GND
33
LV-675 User’s Manual
2.14 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED Power
LED
Reset
Power
Button
PWRBT+ 11
PWRBT- 13
12
14
N/C
N/C
SPK-
Speaker
1 2
JFRNT
13 14
34
LV-673 User’s Manual
Chapter 3 <System Setup>
3.1 <Video Memory Setup>
Based on Intel® 845GV chipset , the board supports Intel® DVMT (Dynamic Video
Memory Technology) 3.0, which would allow the video memory to be allocated up to
64MB.
To support DVMT, you need to install the Intel GMA Driver with supported OS.
BIOS Setup:
On-Chip Video Memory Size: This option combines three items below for setup.
On-Chip Frame Buffer Size:
This item can let you select video memory which been allocated for legacy VGA and
SVGA graphics support and compatibility. The available option is 1MB and 8MB.
Fixed Memory Size:
This item can let you select a static amount of page-locked graphics memory which will be allocated during driver initialization. Once you select the memory amount, it will be no longer available for system memory.
35
LV-675 User’s Manual
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for
IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 4-1. You can use arrow keys to select your function, press <Enter> key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
36
LV-675 User’s Manual
(This Page is Left for Blank)
37
LV-675 User’s Manual
Appendix A <I/O Port Pin Assignment>
38
A.1 <IDE Port>
Connector: IDE1
Type: 40-pin (20 x 2) box header
Pin Description Pin Description
1 Reset
3 D7
5 D6
7 D5
9 D4
11 D3
13 D2
15 D1
17 D0
2 Ground
4 D8
6 D9
8 D10
10 D11
12 D12
14 D13
16 D14
18 D15
19 Ground
21 REQ
20 VCC
22 Ground
23 IOW-/STOP 24 Ground
25 IOR-/HDMARDY 26 Ground
27 IORDY/DDMARDY 28 IDESEL
29 DACK- 30 Ground
31 IRQ
33 A1
32 N/C
34 P66DET
35 A0
37 CS0 (MASTER CS)
36 A2
38 CS1 (SLAVE CS)
40 Ground
LV-675 User’s Manual
Connector: IDE2
Type: 44-pin (22 x 2) box header
Pin Description
1 Reset
3 D7
5 D6
7 D5
9 D4
11 D3
13 D2
15 D1
17 D0
19 Ground
21 REQ
23 -IOW
25 -IOR
27 IORDY
29 DACK
31 IDEIRQ
33 A1
35 A0
37 -CS1
41 +5V
43 Ground
Pin Description
2 Ground
4 D8
6 D9
8 D10
10 D11
12 D12
14 D13
16 D14
18 D15
20 N/C
22 Ground
24 Ground
26 Ground
28 IDSEL
30 Ground
32 IDE32
34 P66DET
36 A2
38 -CS3
40 Ground
42 +5V
44 Ground
39
LV-675 User’s Manual
A.2 <Floppy Port>
Connector: FDD
Type: 26-pin connector
Pin Description
1 VCC
3 VCC
5 VCC
7 N/C
9 N/C
11 DRVDE0
13 N/C
15 Ground
17 Ground
19 Ground
21 N/C
23 Ground
25 Ground
A.3 <IrDA Port>
Connector: CN_IR
Type: 5-pin header for SIR Ports
Pin Description
1 VCC
2 N/C
3 IRRX
4 Ground
5 IRTX
Pin Description
2 INDEX
4 DR0
6 DSKCH
8 N/C
12 DIR
14 STEP
22 WRPRO
24 RDATA-
26 SEL
1
5
40
LV-675 User’s Manual
A.4 <Serial Port>
Connector: COM1/COM2
Type: 9-pin pin header connector
Pin Description
1
9
2
5 Ground
Pin Description
6 DSR-
7 RTS-
8 CTS-
9 RI
A.5 <VGA Port>
3
4
1
2
5
6
Connector: VGA
Type: 15-pin D-sub female connector on bracket
Pin Description Pin Description Pin
10
11
12
13
14
15
Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 +5V
3 BLUE 8 Ground 13 5HSYNC
4 N/C 9 N/C 14 5VSYNC
5 -CRTATCH 10 Ground 15 5VCLK
A.6 <LAN Port>
Connector: RJ45
Type: RJ45 connector with LED on bracket
Pin 1 2 3 4 5
Description TRD0+ TRD0- TRD1+ TRD1NC
Pin 6 7 8 9 10
Description NC TRD2+ TRD2- TRD3+ TRD3-
41
LV-675 User’s Manual
A.7 < USB Interface >
1
Connector: CN_USB
Type: 10-pin (5 x 2) header for dual USB Ports
Pin Description Pin Description
9
1 VCC
3 Data0-
5 Data0+
7 Ground
9 Ground
2 VCC
4 Data1-
6 Data1+
8 Ground
2
10
A.8 < LPT Port >
42
Connector : LPT
Type :26-Pin D-Sub female Connector on bracket
Pin Description
1 -PSTB
3 PRO1
5 PRO3
7 PRO5
9 PRO7
11 BUSY
13 SLCT
15 ERR-
17 SLIN-
19 Ground
21 Ground
23 Ground
25 Ground
Pin Description
2 PRO0
4 PRO2
6 PRO4
8 PRO6
12 PE
14 AFD-
16 INT-
18 Ground
22 Ground
24 Ground
26 N/C
LV-675 User’s Manual
Appendix B <Flash BIOS>
B.1 <Flash Tool>
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.phoenix.com/en/home/ http://www.commell.com.tw/Support/Support_SBC.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
B.2 <Flash BIOS Procedure>
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Restart the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below: http://www.commell.com.tw/support/support.htm
43
44
LV-675 User’s Manual
Appendix C <System Resources>
C1.<I/O Port Address Map>
LV-675 User’s Manual
45
LV-675 User’s Manual
C2.<Memory Address Map>
46
LV-675 User’s Manual
C3.<System IRQ & DMA Resources>
DMA:
IRQ:
47
LV-675 User’s Manual
The GPIO’can be programmed with the MSDOS debug program using simple
IN/OUT commands.The following lines show an example how to do this.
GPIO0…..GPIO7 bit0……bit7
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 29
-o 2E 40 ;enale GPIO function
-o 2E 07
-o 2E 07 ;enable GPIO configuration
-o 2E F0
-o 2F xx ;set GPIO as input/output; set ‘1’ for input,’0’for output
-o 2E F1
-o 2F xx ;if set GPIO’s as output,in this register its value can be set
Optional :
-o 2E F2
-o 2F xx ; Data inversion register ; ‘1’ inverts the current valus of the bits ,’0’ leaves them as they are
-o 2E 30
-o 2F 01 ; active GPIO’s
For further information ,please refer to Winbond W83627HF datasheet.
48
LV-675 User’s Manual
Appendix D <Display Setting>
Before you using your display device:
1. Check your software
Before you can use the display device properly, please install the VGA drivers.
2. Check your hardware
Please setup the display device properly before you boot up the system.
For configure your Display device, please follow the instructions below:
1. lunch the display properties.
2. Select settings option and click Advanced Button
3. Select Intel(R) Extreme Graphics and click Graphics properties
49
LV-675 User’s Manual
4. There will be a different device list depends on your connecting devices
For Monitor:
You can configure the Colors, Screen area (resolution) and Refresh Rate.
For Notebook:
If you connect a LCD panel though LVDS
50 interface, you can configure the Colors and Screen Area (resolution) here.
LV-675 User’s Manual
Appendix E <How to choose RS-422 & Rs-485>
1 2
5 6
JCSEL1
RS-232
1 3
10
JCSEL2
12
JCSEL1
RS-485
JCSEL2
JCSEL2
JCSEL1
RS-422
JCSEL2
JCSEL1
51
LV-675 User’s Manual
Appendix F <Programming Watchdog Timer >
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
-o 2E 87 ;enter configuration
-o 2E 87
-o 2E 07
-o 2F 08 ;enter Logical Device 8
-o 2E F5
-o 2F 00 ;set as Second* Minute: bit 3 = 1; Second: bit 3 = 0
-o 2E F6
-o 2F 05 ;set as 5 Second
52
LV-675 User’s Manual
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us.
We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address 8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
TEL +886-2-26963909
FAX +886-2-26963911
Website
E-Mail http://www.commell.com.tw
(General Information) [email protected]
(Technical Support)
53

Public link updated
The public link to your chat has been updated.
Advertisement