www.proform.com

Model No. PFEL03815.2

Serial No.

Write the serial number in the space above for reference.

Serial

Number

Decal

ACTIVATE YOUR

WARRANTY

To register your product and activate your warranty today, go to www.proformservice.com/ registration.

CUSTOMER CARE

For service at any time, go to www.proformservice.com.

Or call 1-888-533-1333

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–12 p.m. MT

Please do not contact the store.

CAUTION

Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.

USER’S MANUAL

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

HOW TO USE THE HYBRID TRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning decal(s).

If a decal is missing or illegible, see the front cover of this manual and request a free replacement decal. Apply the decal in the location shown.

Note: The decal(s) may not be shown at actual size.

PROFORM is a registered trademark of ICON Health & Fitness, Inc. IFIT is a registered trademark of ICON

Health & Fitness, Inc. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. Android and Google Play are trademarks of Google Inc. The BLUETOOTH

®

word mark and logos are registered trademarks of Bluetooth SIG, Inc. and are used under license. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

2

IMPORTANT PRECAUTIONS

WARNING:

To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your hybrid trainer before using your hybrid trainer.

ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

1. It is the responsibility of the owner to ensure that all users of the hybrid trainer are adequately informed of all precautions.

9. The hybrid trainer should not be used by persons weighing more than 350 lbs.

(159 kg).

2. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

3. Use the hybrid trainer only as described in this manual.

4. The hybrid trainer is intended for home use only. Do not use the hybrid trainer in a commercial, rental, or institutional setting.

5. Keep the hybrid trainer indoors, away from moisture and dust. Do not put the hybrid trainer in a garage or covered patio or near water.

6. Place the hybrid trainer on a level surface, with at least 3 ft. (0.9 m) of clearance in the front and rear of the hybrid trainer and 2 ft.

(0.6 m) on each side. To protect the floor or carpet from damage, place a mat under the hybrid trainer.

7. Inspect and properly tighten all parts each time the hybrid trainer is used. Replace any worn parts immediately.

8. Keep children under age 12 and pets away from the hybrid trainer at all times.

10. Wear appropriate clothes while exercising; do not wear loose clothes that could become caught on the hybrid trainer. Always wear athletic shoes for foot protection while exercising.

11. Hold the handlebars or the upper body arms when mounting, dismounting, or using the hybrid trainer.

12. Make sure that the pedal knobs are fully tightened each time you use the hybrid trainer.

13. The heart rate monitor is not a medical device. Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.

14. The hybrid trainer does not have a freewheel; the pedals will continue to move until the flywheel stops. Reduce your pedaling speed in a controlled way.

15. Keep your back straight while using the hybrid trainer; do not arch your back.

16. Over exercising may result in serious injury or death. If you feel faint, if you become short of breath, or if you experience pain while exercising, stop immediately and cool down.

3

STANDARD SERVICE PLANS

all

4

BEFORE YOU BEGIN

Thank you for selecting the revolutionary PROFORM

®

HYBRID TRAINER. The HYBRID TRAINER provides an impressive selection of features designed to make your workouts at home more effective and enjoyable.

For your benefit, read this manual carefully before you use the hybrid trainer.

If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.

Upper Body Arm

Heart Rate Monitor

Handlebar

Accessory Tray

Console

Pivot Knob

Seat

Backrest

Carriage Knob

Pedal Brace

Pedal

Length: 5 ft. 11 in. (180 cm)

Width: 2 ft. 1 in. (64 cm)

Leveling Foot

5

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.

Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra parts may be included.

M8 Locknut

(68)–10

M8 Washer

(87)–6

M4 x 16mm

Screw (115)–6

M6 x 20mm

Screw (97)–4

M6 x 35mm Screw

(98)–4

M8 x 12mm

Screw (106)–6

M8 x 14mm

Shoulder

Screw (86)–6

M8 x 38mm

Bolt (95)–4

M8 x 38mm Hex

Bolt (102)–6

M10 x 20mm

Screw (76)–6

M10 x 80mm Screw (19)–4

6

ASSEMBLY

• To hire an authorized service technician to assemble the hybrid trainer, call 1-800-445-2480.

• Assembly requires two persons.

• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you fi nish assembly.

• Left parts are marked “L” or “Left” and right parts are marked “R” or “Right.”

• To identify small parts, see page 6.

• In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one adjustable wrench one rubber mallet

Assembly may be easier if you have a set of wrenches. To avoid damaging parts, do not use power tools.

1.

Go to www.proformservice.com/registration on your computer and register your product.

• activates your warranty

• saves you time if you ever need to contact

Customer Care

• allows us to notify you of upgrades and offers

Note: If you do not have Internet access, call

Customer Care (see the front cover of this manual) and register your product.

1

2. With the help of a second person, place some of the packing materials (not shown) under the

Frame (1).

Orient the Rear Stabilizer (6) so that the large holes are facing the Frame (1). Attach the Rear

Stabilizer to the Frame with two M10 x 80mm

Screws (19).

Then, remove the packing materials from under the Frame (1).

2

6 Large

Holes

19

7

1

3. Orient the Upright (2) and the Front Stabilizer (5) so that the large holes are facing the Upright.

Attach the Front Stabilizer (5) to the Upright (2) with two M10 x 80mm Screws (19).

3

2

Large

Holes

19

5

4. Set the Upright (2) near the Frame (1) as shown.

Locate the wire tie in the Frame (1) and pull the Main Wire (96) out of the underside of the

Frame.

Repeat this action to pull the Upper Wire

(not shown) out of the underside of the

Upright (2).

Then, untie and discard the wire ties.

4

1

Wire Tie

96

2

Wire Tie

8

5.

Tip: Avoid pinching the wires.

Insert the

Upright (2) into the Frame (1).

Attach the Upright (2) with six M10 x 20mm

Screw (76);

start all the Screws, and then tighten them.

Then, connect the Upper Wire (94) to the Main

Wire (96).

5

Avoid pinching the wires

76

1

76

2

96

76

94

6. Locate the wire tie in the top of the Upright (2) and pull the Upper Wire (94) out of the Upright.

Then, untie and discard the wire tie.

Tip: Avoid pinching the wires.

Attach the Wire

Cover (20) to the Frame (1) and the Upright (2) with two M4 x 16mm Screws (115).

Make sure that the tab on the Wire Cover is in the location shown.

6

94

Wire

Tie

Avoid pinching the wires

1

2

20

115

Tab

9

7. Have a second person hold the Pivot Bracket (3) near the Upright (2).

Locate the wire tie in the Pivot Bracket (3). Tie the wire tie to the Upper Wire (94) and then pull the other end of the wire tie until the Upper Wire is routed through the Pivot Bracket.

7

Wire Tie

3

2

94

Wire Tie

8. Using a plastic bag to keep your fingers clean, apply a generous amount of the included grease to the Pivot Axle (80).

Tip: Avoid pinching the Upper Wire (94).

Slide the Pivot Bracket (3) onto the Upright (2) and hold it in place.

Next, insert the Pivot Axle (80) into the Pivot

Bracket (3) and into the Upright (2). Center the

Pivot Axle.

Then, tighten the Pivot Knob (13) into the Pivot

Bracket (3).

8

94

13

2

3

Avoid pinching the Upper

Wire (94)

80

Grease

10

9. Identify the Right Pedal Arm (9) and the Right

Pivot Leg (8), and orient them as shown.

Apply a generous amount of the included grease to the axle on the Right Pivot Leg (8).

Then, slide the Right Pedal Arm (9) onto the

Right Pivot Leg (8). Attach the Right Pedal Arm with an M8 x 14mm Shoulder Screw (86), a Pivot

Cover (83), and an M8 Washer (87).

Repeat this step for the Left Pedal Arm (not shown) and the Left Pivot Leg (not shown).

9

86

83

87

9

8

Grease

10. Slide a Pivot Spacer (79) onto each side of the

Pivot Axle (80).

Then, slide the Right and Left Pivot Legs (8, 11) onto the Pivot Axle (80);

make sure that the

Pivot Legs are on the correct sides.

Then, tighten an M8 x 14mm Shoulder Screw

(86), a Pivot Cover (83), and an M8 Washer (87) into each end of the Pivot Axle (80)

at the same time.

10

86

83

87

11

79

80

79

87

83

86

8

11

11. Remove and discard the packaging on the Right

Crank Bracket (30). Then, tighten an M8 x 14mm

Shoulder Screw (86) with a Pivot Cover (83) and an M8 Washer (87) into the right Crank Arm (24).

Next, slide the Right Pedal Arm (9) onto the

Right Crank Bracket (30).

Then, attach the Right Pedal Arm (9) with three

M8 x 12mm Screws (106);

start all the Screws, and then tighten them.

Repeat this step on the other side of the hybrid trainer.

11

24

87

30

9

106

86

83

12. The Console (4) requires four D batteries (not included); alkaline batteries are recommended.

Do not use old and new batteries together or alkaline, standard, and rechargeable batteries together.

IMPORTANT: If the Console has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries. Otherwise, you may damage the console displays or other electronic components.

Remove the screws and the battery cover from the back of the Console (4), insert batteries into the battery compartment, and then reattach the battery cover.

Make sure to orient the batteries as shown by the diagrams inside the battery compartment.

To purchase an optional power adapter, call the telephone number on the cover of this manual. To avoid damaging the console, use only a manufacturer-supplied regulated power adapter.

Plug one end of the power adapter into the receptacle

inside

the battery compartment on the console and route the power adapter through the notch in the battery cover; plug the other end into an outlet installed in accordance with all local codes and ordinances.

12

4

Battery

Cover

12

13. Untie and discard the wire tie on the Upper

Wire (94).

While a second person holds the Console (4) near the Pivot Bracket (3), plug the Upper Wire

(94) and the Left and Right Pulse Wires (103,

104) into the receptacles on the Console.

The connectors on the Wires (94, 103, 104) should slide easily into the receptacles and snap into place.

If a connector does not slide easily into a receptacle, turn the connector and try again.

If you do not connect the connectors properly, the Console (4) may become damaged when you use the hybrid trainer.

Insert the excess wire into the Pivot Bracket (3).

Tip: Avoid pinching the wires.

Attach the

Console (4) to the Pivot Bracket (3) with four

M4 x 16mm Screws (115);

start all the Screws, and then tighten them.

13

4

94

103, 104

14. Identify the Right Upper Body Arm (7).

Orient an Upper Body Cover (78) as shown, and slide it upward onto the Right Upper Body

Arm (7).

Attach the Right Upper Body Arm (7) to the Right

Pivot Leg (8) with three M8 x 38mm Hex Bolts

(102) and three M8 Locknuts (68);

start all the

Hex Bolts, and then tighten them. Make sure that the Locknuts are inside the hexagonal holes.

Then, slide the Upper Body Cover (78) downward onto the Right Pivot Leg (8).

Repeat this step on the other side of the hybrid trainer.

14

68

Hexagonal Holes

68

3

Avoid pinching the wires

115

78

8

7

102

13

15. Orient the Seat Frame (61) as shown.

Insert a Seat Handlebar (29) into the Seat

Frame (61). Attach the Seat Handlebar with two

M8 x 38mm Bolts (95) and two M8 Locknuts

(68);

make sure that the Locknuts are in the hexagonal holes.

Repeat this step to attach the other Seat

Handlebar (29).

15

29

95

61

29

68

Hexagonal

Holes

16. Attach the Seat Frame (61) to the Seat Carriage

(32) with four M6 x 35mm Screws (98);

start all the Screws, and then tighten them.

16

98

98

61

32

14

17. Attach the Seat (28) to the Seat Frame (61) with four M6 x 20mm Screws (97) (only two are shown);

start all the Screws, and then tighten them.

17

28

61

97

18.

Make sure that all parts of the hybrid trainer are properly tightened.

Note: Extra parts may be included.

To protect the floor or carpet from damage, place a mat under the hybrid trainer.

15

HOW TO USE THE HYBRID TRAINER

HOW TO MOVE THE HYBRID TRAINER

Lift the rear stabilizer until the hybrid trainer will roll on the wheels. Carefully move the hybrid trainer to the desired location, and then lower it to the floor.

Lift here

HOW TO USE THE TABLET HOLDER

IMPORTANT: The tablet holder was designed for use with most full-size tablets and smart phones. Do not place any other electronic device or object into the tablet holder.

To insert a tablet or smart phone into the tablet holder, set the bottom edge of the tablet or smart phone in the tray.

Make sure that the tablet or smart phone is firmly secured in the tablet holder.

Reverse these actions to remove the tablet or smart phone from the tablet holder.

HOW TO USE THE ELLIPTICAL MODE

To use the hybrid trainer as an elliptical, first pivot the pivot bracket to the high position and tighten the pivot knob into the upright.

HOW TO LEVEL THE HYBRID TRAINER

If the hybrid trainer rocks slightly on your floor during use, turn one or both of the leveling feet beneath the rear of the frame until the rocking motion is eliminated.

Leveling

Feet

Knob

Then, lift a pedal, fold the brace upward, and pivot the pedal downward to the low position.

Repeat this action for the other pedal.

Brace

16

To mount the hybrid trainer in the elliptical mode, hold the handlebars or the upper body arms and step onto the pedal that is in the lower position.

Then, step onto the other pedal.

Upper Body Arms

Handlebars

HOW TO USE THE RECUMBENT BIKE MODE

To use the hybrid trainer as a recumbent bike, loosen the pivot knob and pivot the pivot bracket to the low position.

Knob

Pedals

Next, lift a pedal, unfold the brace, and insert the end of the brace into the pedal arm.

Make sure that the brace is securely inserted into the pedal arm.

Repeat this action for the other pedal.

Crank Arm

Push the pedals until they begin to move with a continuous motion.

Note: The crank arms can turn in either direction. It is recommended that you move the crank arms in the direction shown by the arrow; however, for variety, you can turn the crank arms in the opposite direction.

To dismount the hybrid trainer, wait until the pedals come to a complete stop.

Note: The hybrid trainer does not have a free wheel; the pedals will continue to move until the flywheel stops.

When the pedals are stationary, step off the higher pedal first.

Then, step off the lower pedal.

Brace

Pedal

Arm

Then, adjust the seat forward or backward to the position that is the most comfortable.

To adjust the seat, loosen the carriage knob and pull it

Knob outward, slide the seat to the desired position, and then release the carriage knob into an adjustment hole on the frame.

Make sure that the carriage knob is securely inserted into an adjustment hole.

Then, tighten the carriage knob.

17

CONSOLE DIAGRAM FEATURES OF THE CONSOLE

The advanced console offers an array of features designed to make your workouts more effective and enjoyable.

When you use the manual mode of the console, you can change the resistance of the pedals with the touch of a button. As you exercise, the console will provide continuous exercise feedback. You can even measure your heart rate using the handgrip heart rate monitor or a compatible heart rate monitor.

See page 22 for information about purchasing an optional chest heart rate monitor.

You can also connect your smart device to the console and use an iFit information.

®

app to record and track your workout

The console also offers sixteen preset workouts—eight workouts for the recumbent bike mode and eight workouts for the elliptical mode. Each workout automatically changes the resistance of the pedals and prompts you to vary your pedaling speed while guiding you through an effective workout.

You can even connect your MP3 player or CD player to the console sound system and listen to your favorite music or audio books while you exercise.

To use the manual mode,

see page 19.

To use the sound system,

see page 20.

To use a preset workout,

see page 21.

To connect your smart device to the console,

see page 22.

To connect your heart rate monitor to the console,

see page

22.

To use the settings mode,

see page 23.

Note: Before using the console, make sure that batteries are installed (see assembly step 12 on page

12). If there is a sheet of plastic on the display, remove the plastic.

18

HOW TO USE THE MANUAL MODE

1. Turn on the console.

Press any button or begin pedaling to turn on the console.

When you turn on the console, the displays will turn on, a tone will sound, and the console will be ready for use.

2. Select the manual mode.

When you turn on the console, the manual mode will be selected automatically.

If you have selected a workout, reselect the manual mode by pressing the On/

Reset button.

3. Begin pedaling and change the resistance of the pedals as desired.

As you pedal, change the resistance of the pedals by pressing the Resistance increase and decrease buttons.

Note: After you press the buttons, it will take a moment for the pedals to reach the selected resistance level.

4. Follow your progress with the displays.

The speed meter

—This display will provide a visual representation of your pedaling speed. As you increase or decrease your pedaling speed, bars will appear or disappear in the speed meter.

Note: During a preset workout, this display will show a target speed zone for each segment of the workout.

The upper display

—This display will show your pedaling speed in revolutions per minute (RPM) and your power output in watts. The display will change every few seconds.

This display will also show the resistance level of the pedals for a few seconds each time the resistance level changes.

This display will also show your heart rate (BPM) when you use the handgrip heart rate monitor or a compatible heart rate monitor (see step 5).

The center display

—This display will show the distance

(Dist.) you have pedaled in miles or kilometers and the elapsed time. The display will change every few seconds.

Note: During a preset workout, the display will show the time remaining in the workout instead of the elapsed time.

The lower display

—This display will show your pedaling speed in miles per hour or kilometers per hour and the approximate number of calories (Cals.) you have burned. The display will change every few seconds.

To select an information mode for continuous display, press the Display button repeatedly until the desired information is shown in the display.

To return to alternating the information that is shown in the displays, press the Display button repeatedly until the word SCAN appears in the center display.

Change the volume level of the console by pressing the Volume increase and decrease buttons.

19

To pause the console, stop pedaling. When the console is paused, the displays will pause.

To continue your workout, simply resume pedaling.

To reset the displays to zero, press the On/Reset button.

Note: The console can show pedaling speed and distance in either miles or kilometers. To change the unit of measurement, see THE SETTINGS

MODE on page 23.

5. Measure your heart rate if desired.

You can measure your heart rate using either the handgrip heart rate monitor or a compatible heart rate monitor. For information about purchasing an optional chest heart rate monitor, see page 22.

The console is compatible with all BLUETOOTH rate monitor to the console, see page 22.

®

Smart heart rate monitors. To connect your heart

Note: If you use both heart rate monitors at the same time, the BLUETOOTH Smart heart rate monitor will have priority.

If there are sheets of plastic on the metal contacts on the handgrip heart rate monitor, remove the plastic.

In addition, make sure that your hands are clean.

To measure

Contacts your heart rate, hold the handgrip heart rate monitor with your palms resting against the contacts.

Avoid moving your hands or gripping the contacts tightly.

When your pulse is detected, your heart rate will be shown in the upper display.

For the most accurate heart rate reading, hold the contacts for at least

15 seconds.

If your heart rate is not shown, make sure that your hands are positioned as described. Be careful not to move your hands excessively or to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth;

never use alcohol, abrasives, or chemicals to clean the contacts.

6. When you are finished exercising, the console will turn off automatically.

If the pedals do not move for several seconds, a series of tones will sound, the console will pause, and displays will pause.

If the pedals do not move for several minutes, the console will turn off and the displays will be reset.

HOW TO USE THE SOUND SYSTEM

To play music or audio books through the console sound system while you exercise, plug a 3.5 mm male to 3.5 mm male audio cable (not included) into the jack on the console and into a jack on your MP3 player,

CD player, or other personal audio player;

make sure that the audio cable is fully plugged in. Note: To purchase an audio cable, see your local electronics store.

Next, press the play button on your personal audio player.

Adjust the volume level using the volume increase and decrease buttons on the console or the volume control on your personal audio player.

20

HOW TO USE A PRESET WORKOUT

1. Turn on the console.

Press any button or begin pedaling to turn on the console.

When you turn on the console, the displays will turn on, a tone will sound, and the console will be ready for use.

2. Select a preset workout.

When you select a Recumbent preset workout,

you must adjust the hybrid trainer to the recumbent bike mode for the console to provide accurate feedback (see HOW TO USE THE RECUMBENT BIKE

MODE on page 17).

When you select an Elliptical preset workout,

you must adjust the hybrid trainer to the elliptical mode for the console to provide accurate feedback

(see HOW TO USE THE ELLIPTICAL MODE on page 16).

To select a preset workout, press the Elliptical Workouts or Recumbent Workouts button repeatedly until the number of the desired workout appears in the lower display. The duration of the workout will appear in the center display.

3. Start the workout.

Begin pedaling to start the workout.

Each workout is divided into one-minute segments.

One resistance level and one speed target speed are programmed for each segment. Note: The same resistance level and/or target speed may be programmed for consecutive segments.

At the end of each segment of the workout, a series of tones will sound. The resistance level for the next segment will appear in the upper display for a few seconds to alert you. The resistance of the pedals will then change.

The speed meter will show two flashing bars that represent the target speed zone for the segment; the target speed zone includes a range of speeds that are within a few RPMs of the target

Target

Speed

Zone speed for the segment. The solid bars represent your actual pedaling speed.

As you exercise, keep your pedaling speed within the target speed zone for the current segment by increasing or decreasing your pedaling speed or by increasing or decreasing the resistance of the pedals.

IMPORTANT: The target speed is intended only to provide motivation. Make sure to pedal at a speed and a resistance level that is comfortable for you.

If the resistance level for the current segment is too high or too low, you can manually override the setting by pressing the Resistance buttons.

IMPORTANT: When the current segment of the workout ends, the pedals will automatically adjust to the resistance level programmed for the next segment.

If you stop pedaling for several seconds, a series of tones will sound and the workout will pause.

To restart the workout, simply resume pedaling.

The workout will continue until the last segment of the workout ends.

4. Follow your progress with the displays.

See step 4 on page 19.

5. Measure your heart rate if desired.

See step 5 on page 20.

6. When you are finished exercising, the console will turn off automatically.

See step 6 on page 20.

21

THE OPTIONAL CHEST HEART RATE MONITOR

Whether your goal is to burn fat or to strengthen your cardiovascular system, the key to achieving the best results is to maintain the proper heart rate during your workouts. The optional chest heart rate monitor will enable you to continuously monitor your heart rate while you exercise, helping you to reach your personal fitness goals.

To purchase a chest heart rate monitor, please see the front cover of this manual.

Note: The console is compatible with all BLUETOOTH

Smart heart rate monitors.

HOW TO CONNECT YOUR SMART DEVICE TO THE

CONSOLE

The console supports BLUETOOTH connections to smart devices via the iFit app and to compatible heart rate monitors. Note: Other BLUETOOTH connections are not supported.

1. Download and install the iFit app on your smart device.

On your iOS

®

or Android™ smart device, open the

App Store ℠ or the Google Play™ store, search for the free iFit app, and then install the app on your smart device.

Make sure that the BLUETOOTH option is enabled on your smart device.

Then, open the iFit app and follow the instructions to set up an iFit account and customize settings.

2. Connect your smart device to the console.

Follow the instructions in the iFit app to connect your smart device to the console.

When a connection is established, the LED on the console will flash blue. Press the Bluetooth Smart button on the console to confirm the connection; the LED on the console will then turn solid blue.

3. Record and track your workout information.

Follow the instructions in the iFit app to record and track your workout information.

4. Disconnect your smart device from the console if desired.

To disconnect your smart device from the console, press and hold the Bluetooth Smart button on the console for 5 seconds; the LED on the console will light while the button is held and turn off when the button is released.

Note: All BLUETOOTH connections between the console and other devices (including any smart devices, heart rate monitors, and so forth) will be disconnected.

HOW TO CONNECT YOUR HEART RATE MONITOR

TO THE CONSOLE

The console is compatible with all BLUETOOTH Smart heart rate monitors.

To connect your BLUETOOTH Smart heart rate monitor to the console, press the Bluetooth Smart button on the console. When a connection is established, the

LED on the console will flash red twice.

Note: If there is more than one compatible heart rate monitor near the console, the console will connect to the heart rate monitor with the strongest signal.

To disconnect your heart rate monitor from the console, press and hold the Bluetooth Smart button on the console for 5 seconds; the LED on the console will light while the button is held and turn off when the button is released.

Note: All BLUETOOTH connections between the console and other devices (including any smart devices, heart rate monitors, and so forth) will be disconnected.

22

THE SETTINGS MODE

The console features a settings mode that allows you to select a unit of measurement for the console and to view console usage information.

To select the settings mode, press and hold down the

On/Reset button until the settings mode information appears in the display.

The console can show pedaling speed and distance in either miles or kilometers. The upper display will show the selected unit of measurement. An E for

English miles or an M for metric kilometers will appear in the display. To change the unit of measurement, press the Elliptical Workouts button repeatedly.

Note: When you replace the batteries, it may be necessary to reselect the unit of measurement.

Press the Recumbent Workouts button to view the total distance and the total time. The center display will show the total time (in hours) that the console has been used since the hybrid trainer was purchased. The lower display will show the total distance (in miles or kilometers) that the hybrid trainer has been pedaled.

To exit the settings mode, press the On/Reset button twice.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

23

MAINTENANCE AND TROUBLESHOOTING

MAINTENANCE

Regular maintenance is important for optimal performance and to reduce wear. Inspect and properly tighten all parts each time the hybrid trainer is used.

Replace any worn parts immediately.

To clean the hybrid trainer, use a damp cloth and a small amount of mild soap.

IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

CONSOLE TROUBLESHOOTING

Most console problems are the result of low batteries. To replace the batteries, see assembly step 12 on page 12.

If the console does not display your heart rate when you use the handgrip heart rate monitor, see step 5 on page 20.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted.

To adjust the reed switch, first remove the two

M4 x 19mm Selftapping Screws

(100) from the

Rear Access

Cover (26), and then remove the

Rear Access

Cover.

100

26

Next, locate the Reed Switch (60). Loosen, but do not remove, the two M4 x 19mm Screws (84).

48

117

60

84

Next, rotate the Large Pulley (48) until a Pulley Magnet

(117) is aligned with the Reed Switch (60). Slide the

Reed Switch slightly toward or away from the Pulley

Magnet. Then, retighten the M4 x 19mm Screws (84).

Rotate the Large Pulley (48) for a moment. Repeat these actions until the console displays correct feedback.

When the reed switch is correctly adjusted, reattach the rear access cover.

24

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling, even when the resistance is adjusted to the highest level, the drive belt may need to be adjusted.

To adjust the drive belt, first remove the M4 x 19mm

Self-tapping Screw (100) from the Side Access Cover

(21), and then remove the Side Access Cover by moving it in the direction shown by the arrow.

Next, loosen the M10 x 55mm Bolt (99). Then, tighten the M8 Locknut (68) until the Drive Belt (64) is tight.

68

64

99

When the Drive Belt (64) is tight, tighten the M10 x

55mm Bolt (99). Then, reattach the side access cover.

100

21

25

EXERCISE GUIDELINES

WARNING:

Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

The heart rate monitor is not a medical device.

Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.

These guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consult your physician. Remember, proper nutrition and adequate rest are essential for successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your heart rate as a guide to find the proper intensity level.

The chart below shows recommended heart rates for fat burning and aerobic exercise.

To find the proper intensity level, find your age at the bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your age define your “training zone.” The lowest number is the heart rate for fat burning, the middle number is the heart rate for maximum fat burning, and the highest number is the heart rate for aerobic exercise.

Burning Fat

—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone. For maximum fat burning, exercise with your heart rate near the middle number in your training zone.

Aerobic Exercise

—If your goal is to strengthen your cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone.

WORKOUT GUIDELINES

Warming Up

—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body temperature, heart rate, and circulation in preparation for exercise.

Training Zone Exercise

—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During the first few weeks of your exercise program, do not keep your heart rate in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise ; never hold your breath.

Cooling Down

—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles and helps to prevent post-exercise problems.

EXERCISE FREQUENCY

To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is to make exercise a regular and enjoyable part of your everyday life.

26

SUGGESTED STRETCHES

The correct form for several basic stretches is shown at the right. Move slowly as you stretch; never bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax.

Repeat 3 times. Stretches: Hamstrings, back of knees and back.

2. Hamstring Stretch

1

Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax.

Repeat 3 times for each leg. Stretches: Hamstrings, lower back and groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg.

To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.

3

2

4

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg.

Stretches: Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees outward.

Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.

5

27

PART LIST

Key No. Qty. Description

25

26

27

28

29

30

31

32

17

18

19

20

21

22

23

24

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

41

42

43

44

45

46

47

48

49

50

33

34

35

36

37

38

39

40

2

1

2

1

1

1

1

1

1

1

1

2

2

2

4

1

1

1

2

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

2

1

1

1

1

1

1

4

4

2

1

2

1

Frame

Upright

Pivot Bracket

Console

Front Stabilizer

Rear Stabilizer

Right Upper Body Arm

Right Pivot Leg

Right Pedal Arm

Left Upper Body Arm

Left Pivot Leg

Left Pedal Arm

Pivot Knob

Accessory Tray

Upper Body Grip

Pulse Grip

Wheel Cap

Crank Cap

M10 x 80mm Screw

Wire Cover

Side Access Cover

Left Shield

Right Shield

Crank Arm

Pivot Cover

Rear Access Cover

Backrest

Seat

Seat Handlebar

Right Crank Bracket

Seat Grip

Seat Carriage

Seat Handlebar Cap

Seat Carriage Bracket

Seat Carriage Bushing

Adjustment Pin

Carriage Knob

M5 x 10mm Screw

M6 x 10mm Bolt

M6 x 16mm Screw

Carriage Cap

Stabilizer Cap

C-magnet

Resistance Motor

Resistance Arm

Resistance Disc

Resistance Block

Large Pulley

Crank

Weld Spacer

28

Model No. PFEL03815.2 R0915B

Key No. Qty. Description

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

59

60

61

62

63

64

65

66

51

52

53

54

55

56

57

58

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

2

1

2

2

2

6

1

2

1

2

2

2

1

23

3

1

1

2

14

1

1

1

1

2

1

2

1

1

6

1

1

1

4

1

4

4

2

8

–

1

1

3

7

2

2

1

6

21

4

6

Crank Bearing

Bearing Spacer

Crank Collar

Idler Axle

Idler Bolt

Idler Bushing

Idler Bracket

Small Pulley

Flywheel

Reed Switch/Wire

Seat Frame

Leveling Foot

Clamp

Drive Belt

Pivot Bushing

Left Crank Bracket

Set Screw

M8 Locknut

Crank Screw

Right Pedal

Left Pedal

Pedal Plate

Bumper

Pedal Brace

Upper Body Cap

M10 x 20mm Screw

M5 x 6mm Screw

Upper Body Cover

Pivot Spacer

Pivot Axle

Pivot Leg Cap

Wheel

Pivot Cover

M4 x 19mm Screw

Foot

M8 x 14mm Shoulder Screw

M8 Washer

M5 Nut

M5 x 10mm Black Screw

M4 x 10mm Screw

M5 Washer

M8 x 20mm Bolt

(Not Used)

Upper Wire

M8 x 38mm Bolt

Main Wire

M6 x 20mm Screw

M6 x 35mm Screw

M10 x 55mm Bolt

M4 x 19mm Self-tapping Screw

Key No. Qty. Description

101

102

103

104

105

106

107

108

109

110

111

2

6

1

1

8

6

2

1

2

1

4

M8 x 54mm Shoulder Screw

M8 x 38mm Hex Bolt

Left Pulse Wire

Right Pulse Wire

M6 x 15mm Screw

M8 x 12mm Screw

M8 x 98mm Bolt

M4 x 19mm Bright Screw

M10 x 110mm Shoulder Bolt

M10 Locknut

M6 Locknut

Key No. Qty.

112

113

114

115

116

117

118

*

*

*

8

2

1

6

5

2

2

–

–

–

Description

M8 Split Washer

M19 Snap Ring

M8 Snap Ring

M4 x 16mm Screw

M4 x 12mm Screw

Pulley Magnet

Clip Nut

User’s Manual

Assembly Tool

Grease Packet

Note: Specifications are subject to change without notice.

For information about ordering replacement parts, see the back cover of this manual. *These parts are not illustrated.

29

EXPLODED DRAWING A

105 84

Model No. PFEL03815.2 R0915B

30

EXPLODED DRAWING B

Model No. PFEL03815.2 R0915B

31

85 84

ORDERING REPLACEMENT PARTS

To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:

• the model number and serial number of the product (see the front cover of this manual)

• the name of the product (see the front cover of this manual)

• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING near the end of this manual)

LIMITED WARRANTY

IMPORTANT: To protect your fitness equipment with an extended service plan, see page 4.

ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and material, under normal use and service conditions. The frame is warranted for fi ve (5) years from the date of purchase. Parts and labor are warranted for ninety (90) days from the date of purchase.

This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers.

All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a service center, freight charges to and from the service center will be the customer’s responsibility. If replacement parts are shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.

This warranty does not extend to freight damage to the product. This warranty will automatically be voided if the product is used as a store display model, if the product is purchased or transported outside the USA, if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used, or if the product is used for commercial or rental purposes. No other warranty beyond that specifi cally set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of property, loss of revenues or profi ts, loss of enjoyment or use, or costs of removal or installation; or other consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to the customer.

The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of merchantability or fi tness for a particular purpose are limited in their scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to the customer.

This warranty provides specifi c legal rights; the customer may have other rights that vary from state to state.

ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813

Part No. 372850 R0915B Printed in China © 2015 ICON Health & Fitness, Inc.