Machine Automation Controller

NX1P

2 Machine Automation Controller NX1P

Open industrial Ethernet network

• Interface with HMI

• Peer-to-Peer controller communication

• Interface with Sysmac Studio

• Information network

(host application)

SD memory card

• Back up, restore, and verify data in the controller

SD memory card

•

Option board controller

• RS-232, RS-422A/485

• Analog I/O

Option board

Add serial communications or analog

Build a cost saving weighing/measurement

Build a cost effective weighing/measurement system using load cells.

system by using load cells

(Modbus-RTU: 32 nodes max.)

Load Cell Input Unit

NX-RS

Load Cell Input Unit

NX-RS

Temperature control made easy - build a temperature control system with heater burnout detection

Temperature Input Unit

NX-TS

Heater Burnout Detection Unit

NX-HB

IO-Link Master Unit

NX-ILM400

3

2

The fast machine network for a wide range of field and motion devices.

Machine Automation Controller

Machine Automation Controller

NX1P

Battery-free NX1P and 1S

The NX1P requires no battery to retain user program, set values, and variables during power interruption in the built-in memory.

They reduce machine maintenance.

They reduce machine maintenance.

Advanced motion control increases

Advanced motion control increases machine speed and precision dedicated controller or special unit. Continuous operation by use require a dedicated controller or special unit. Continuous operation by use of electronic cams improves productivity and meets diverse production needs.

of electronic cams improves productivity and meets diverse

Simplicity for advanced motion control

Simplicity for advanced motion control

1S AC Servo System

Reduce wiring time with Push-In Plus terminals

Push-In Plus terminals deliver the advantage of our

"Value Design for Panel" concept to reduce space, time and cost.

IO-Link connectivity for communication failure often occurs.

failure often occurs.

IO-Link sensor

IO-Link collects information held by sensors and actuators through the

IO-Link collects information held by sensors and actuators through the

IO-Link master and via a fieldbus network into the host controller.

required for commissioning and maintenance.

• • Back up, restore, and

• • RS-232, RS-422A/485

• • Analog I/O

Build a cost effective weighing/measurement

Temperature control made easy - build a temperature control system with heater

Push-In Plus terminals deliver the advantage of our

"Value Design for Panel" concept to reduce space, time and cost.

IO-Link connectivity for communication down to the sensor level advanced motion control

3

Built in EtherCAT and advanced motion control make machines faster and more precise

• EtherCAT simplifies the wiring to up to eight servo systems including for single-axis position control.

• Up to four axes of motion control. Increase machine speed and precision with electronic cams and interpolation.

Interpolation

• Precise machining and high-speed handling

with Linear and circular interpolation

Welding for secondary batteries and bonding

Electronic cam

•

•

High-speed and continuous machine operation using electronic cams

Meet diverse production needs by using electronic cams instead of mechanical cams

CAM control

Motor

Film unwinding

Film pulling

Formed pack feeding axis

Slave axis axis

Packaging machines and filling machines

4

Data transmission delay is compensated to synchronize servomotors.

Synchronized axes provide high-precision positioning.

• Reduce wiring work by using one EtherCAT cable to connect the NX1P and servo drives.

1S AC Servo System

• No battery, no maintenance. No need for homing sequence improving machine uptime

• 23 bit high resolution encoder as standard

• Improved loop control for low overshoot and quick settling time

• Safety function: STO

1S AC Servo System

Machine Automation

Controller

NX1P

5

IO-Link brings IoT to the sensor level

• EtherCAT connects I/O devices, motion devices, safety controllers, and vision systems with a single cable.

You can check machine information by monitoring the status of the connected components.

• EtherNet/IP enables communications with a host PC and data links between NJ/NX Controllers and CJ PLCs.

Big data

Sysmac Automation Platform

The Sysmac Studio integrates programming, configuration, and monitoring, reducing debugging and tuning times

HMI Controller Controller

Controller

Factory automation network

NA

Programmable

Terminal

NX1P Machine

Automation

Controller

NX7 Machine

Automation

Controller

Real-time machine network

NX1P Machine

Automation

Controller

Motion I/O Safety Vision

Intelligent sensing

1S Servo System MX2 Inverter NX I/O IP67 I/O NX Safety

Sensing

Photoelectric sensor

Photoelectric sensor

FH Vision System

Proximity sensor Proximity sensor

Predictive maintenance using IO-Link

With the controller's IO-Link connectivity, you can implement predictive maintenance that lets you visualize machine status at the sensor level.

Proximity

Sensor

Continuous distance monitoring

Wear and vibration of mechanical parts may cause problems

With an IO-Link Proximity Sensor you are notified if the target is too close or too far away, and the occurrence of sudden faults is greatly reduced.

Continuous level monitoring

Photoelectric

Sensor

The incident level drops due to dirt

With an IO-Link Photoelectric Sensor monitoring incident light level prevents false detection. The photoelectric sensor offers several instability settings, allowing you to communicate the incident light level and easily determine when maintenance must be performed.

5

6 Machine Automation Controller NX1P

Machine Automation Controller NX1P

Machine Automation Controller NX-series

NX1P2 CPU Units

24-point type 40-point type

Dimensions

(Unit: mm)

24-point type

130(W)×100(H)×71(D)

40-point type

154(W)×100(H)×71(D)

Option

Boards

Serial

Communications

NX1W-CIF01/

CIF11/CIF12

Analog I/O

NX1W-ADB21/

DAB21V/MAB221

NX Series Up to eight NX Units can be connected to an NX1P2 CPU Unit.

Digital I/O

Units

NX-ID/IA/

OD/OC/MD

Analog I/O

Units

NX-AD/DA

Temperature Input/

Heater Burnout

Detection Units

NX-TS/HB

Load Cell Input

Unit

NX-RS

Position Interface

Units

NX-EC0/

ECS/PG0

Communications

Interface

Unit

NX-CIF

IO-Link

Master Unit

NX-ILM400

System Units

NX-PD/PF/

PC/TBX

6

Automation Software

Sysmac Studio

SYSMAC-SE2£££

Sysmac Studio provides an integrated environment for setting, programming, debugging and maintenance of machine automation controllers including the NJ/NX CPU Units, EtherCAT Slave, and the HMI.

• Fully compliant with open standard IEC 61131-3 and Japanese standard

JIS B3503

• Supports Ladder, Structured Text and Function Block programming with a rich instruction set

• CAM editor for easy programming of complex motion profiles

• One simulation tool for sequence and motion in a 3D environment

• Advanced security function with 32 digit security password

Sysmac is a trademark or registered trademark of OMRON Corporation in Japan and other countries for OMRON factory automation products.

Windows is either registered trademarks or trademarks of Microsoft Corporation in the United Status and/or other countries.

EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.

EtherNet/IP TM is the trademarks of ODVA.

Other company names and product names in this document are the trademarks or registered trademarks of their respective companies.

The product photographs and figures that are used in this catalog may vary somewhat from the actual products.

Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

Ordering Information

Ordering Information

International Standards †

• The standards are abbreviated as follows: UC1: cULus (Class I Division 2 Products for Hazardous Locations), CE: EU Directives, RCM: RCM mark, and KC: KC Registration.

• Contact your OMRON representative for further details and applicable conditions for these standards.

NX1P2 CPU Units

Product name Program capacity

Memory capacity for variables

Maximum number of used real axes

Motion control axes**

Single-axis position control***

Total number of built-in I/O points

Number of input points

Number of output points

40-point

24-point

1.5MB

32 KB

(Retained during power interruptions) and

2 MB

(Not retained during power interruptions)

8 axes

6 axes

4 axes

4 axes

2 axes

0 axes

4 axes

4 axes

4 axes

40 points

24 points

24 points

14 points

Note. One NX-END02 End Cover is provided with the NX1P2 CPU Unit.

* With the load short-circuit protection.

**Motion control axes includes:

- Point to point positioning

- Synchronized motion (Gearing/Camming)

- Multi-Axes coordinated motion (Circular/Linear Interpolation)

- Axes grouping

***Single-axis position control includes:

- Only Point to point positioning

- No Synchronized motion (Gearing/Camming)

- No Multi-Axes coordinated motion (Circular/Linear Interpolation)

- No Axes grouping

16 points,

NPN transistor

16 points,

PNP transistor *

16 points,

NPN transistor

16 points,

PNP transistor *

10 points,

NPN transistor

10 points,

PNP transistor *

Model

NX1P2-1140DT

NX1P2-1140DT1

NX1P2-1040DT

NX1P2-1040DT1

NX1P2-9024DT

NX1P2-9024DT1

Option Boards (For CPU Units)

Product name

Serial

Communications

Option Board

Specification

One RS-232C port. Transmission distance: 15 m.

Connection type: Screwless clamping terminal block (9 terminals).

Serial

Communications

Option Board

Analog Input

Option Board

Supported protocol

One RS-422A/485 port. Transmission distance: 50 m.

Connection type: Screwless clamping terminal block (5 terminals)

One RS-422A/485 port (isolated). Transmission distance: 500 m.

Connection type: Screwless clamping terminal block (5 terminals)

Host link,

Modbus-RTU master, and no-protocol

Analog input: 2

Voltage input: 0 to 10 V (Resolution: 1/4,000). Current input: 0 to 20 mA (1/2,000)

Connection type: Screwless clamping terminal block (5 terminals)

Model

NX1W-CIF01

NX1W-CIF11

NX1W-CIF12

NX1W-ADB21

Standards †

UC1,

CE,

RCM,

KC

Standards

UC1,

CE,

RCM,

KC

Analog Output

Option Board

Analog output: 2

Voltage output: 0 to 10 V (Resolution: 1/4,000)

Connection type: Screwless clamping terminal block (3 terminals)

NX1W-DAB21V

Analog I/O

Option Board

Analog input: 2/Analog output: 2

Voltage input: 0 to 10 V (Resolution: 1/4,000). Current input: 0 to 20 mA (1/2,000)

Voltage output: 0 to 10 V (Resolution: 1/4,000)

Connection type: Screwless clamping terminal block (8 terminals)

NX1W-MAB221

Automation Software Sysmac Studio

Please purchase a DVD and required number of licenses the first time you purchase the Sysmac Studio.

DVDs and licenses are available individually. Each model of licenses does not include DVD.

Product name Specification Number of licenses

Media

Sysmac Studio

Standard Edition

Ver.1.££

Sysmac Studio runs on the following OS:

Windows 7 (32-bit/64-bit version)/Windows 8 (32-bit/64-bit version)/

Windows 8.1 (32-bit/64-bit version)/Windows 10 (32-bit/64-bit version)

The Sysmac Studio Standard Edition DVD includes Support Software to set up EtherNet/IP Units, DeviceNet slaves, Serial Communications Units, and Support Software for creating screens on HMIs (CXDesigner).

For details, refer to the Sysmac Integrated Catalog (Cat. No. P072).

-

(Media only)

1 license *

DVD

-

* Multi licenses are available for the Sysmac Studio (3, 10, 30, or 50 licenses).

Model

SYSMAC-SE200D

SYSMAC-SE201L

7

7

OMRON AUTOMATION AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com

OMRON CANADA, INC. • HEAD OFFICE

Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com

OMRON ELECTRONICS DE MEXICO • HEAD OFFICE

México DF • 52.55.59.01.43.00 • 01-800-226-6766 • [email protected]

OMRON ELECTRONICS DE MEXICO • SALES OFFICE

Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • [email protected]

OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE

São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br

OMRON ARGENTINA • SALES OFFICE

Cono Sur • 54.11.4783.5300

OMRON CHILE • SALES OFFICE

Santiago • 56.9.9917.3920

OTHER OMRON LATIN AMERICA SALES

54.11.4783.5300

OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu

Authorized Distributor: Controllers & I/O

• Machine Automation Controllers (MAC) • Motion Controllers

• Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O

Robotics

• Industrial Robots • Mobile Robots

Operator Interfaces

• Human Machine Interface (HMI)

Motion & Drives

• Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems

• Frequency Inverters

Vision, Measurement & Identification

• Vision Sensors & Systems • Measurement Sensors • Auto Identification Systems

Sensing

• Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors

• Rotary Encoders • Ultrasonic Sensors

Safety

• Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems

• Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices

• Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays

Control Components

• Power Supplies • Timers • Counters • Programmable Relays

• Digital Panel Meters • Monitoring Products

Switches & Relays

• Limit Switches • Pushbutton Switches • Electromechanical Relays

• Solid State Relays

Software

• Programming & Configuration • Runtime

Printed on recycled paper.

W86I-E-01 Note: Specifications are subject to change. © 2016 Omron. All Rights Reserved. Printed in U.S.A.