H4D1FR1(X) User Guide - Honeywell Video Systems

H4D1FR1(X) User Guide - Honeywell Video Systems
equIP® Series 720p
TDN Rugged Network
IR Minidome Camera
NTSC / PAL
H4D1FR1
H4D1FR1X
User Guide
Document 800-12606 – Rev A – 03/2013
User Guide
Revisions
Issue
Date
Revisions
A
03/2013
New document.
| 5
Cautions and Warnings
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING IR emitted from this product. Do not view directly
with optical instruments (magnifiers). Do not stare directly into the
lamp at a distance of less than 3.3 ft (1 m).
CAUTION
Class 1 LED product. Invisible LED radiation (850 nm).
Avoid exposure to beam.
CAUTION
Installation and servicing should be performed only by
qualified and experienced technicians to conform to all local codes and to
maintain your warranty.
CAUTION
24 VAC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with electrical safety standards.
Power over Ethernet (PoE) should meet the IEEE 802.3af PoE standard.
800-12606 - A - 03/2013
6 | H4D1FR1(X) User Guide
Regulatory Statements
FCC Compliance Statement
Information to the User This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
North America The equipment supplied with this guide conforms to UL 60950-1 and
CSA C22.2 No. 60950-1.
Europe The manufacturer declares that the equipment supplied is compliant with the essential
requirements of the EMC directive 2004/108/EC, conforming to the requirements of standards
EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment
safety.
Waste Electrical and Electronic Equipment (WEEE)
Correct Disposal of this Product (applicable in the European Union and other
European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
www.honeywellvideo.com
| 7
Safety Instructions
Before installing or operating the unit, read and follow all instructions. After
installation, retain the safety and operating instructions for future reference.
1.
HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.
2.
INSTALLATION
•
•
•
•
Install in accordance with the manufacturer’s instructions.
Installation and servicing should be performed only by qualified and experienced technicians to
conform to all local codes and to maintain your warranty.
Do not install the unit in an extremely hot or humid location, or in a place subject to dust or
mechanical vibration. The unit is not designed to be waterproof. Exposure to rain or water may
damage the unit.
Any wall or ceiling mounting of the product should follow the manufacturer’s instructions and
use a mounting kit approved or recommended by the manufacturer.
3.
POWER SOURCES - This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supplied to your facility, consult your
product dealer or local power company.
4.
HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers).
5.
WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor installation,
or any area classified as a wet location.
6.
MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer, or sold
with the product.
7.
ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they
may result in the risk of fire, electric shock, or injury to persons.
8.
ACCESSORIES - Only use accessories specified by the manufacturer.
9.
CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
11. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock or other hazards. Using replacement
parts or accessories other than the original manufacturers may invalidate the warranty.
12. DAMAGE REQUIRING SERVICE - Unplug the unit from the outlet and refer servicing to qualified
service personnel under the following conditions:
•
•
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the unit.
If the unit has been exposed to rain or water.
If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the unit to its normal operation.
If the unit has been dropped or the enclosure has been damaged.
When the unit exhibits a distinct change in performance - this indicates a need for service.
13. SAFETY CHECK - Upon completion of any service or repairs to this unit, ask the service technician to
perform safety checks to determine that the unit is in proper operating condition.
800-12606 - A - 03/2013
8 | H4D1FR1(X) User Guide
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty period
Honeywell will repair or replace, at its sole option, free of charge, any defective products
returned prepaid.
In the event that you have a problem with any Honeywell product, please call Customer Service
at 1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available for
the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number
may be refused.
www.honeywellvideo.com
Contents | 9
Contents
About This Document . . . . . .
Overview of Contents. . . .
Related Documents . . . .
Typographical Conventions
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
15
15
16
16
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2
Installing the Camera . . . . . . . .
Before You Begin . . . . . . . . . . .
Parts of the Camera . . . . . . . . .
Preparing to Mount the Camera . . .
Preparing the Camera . . . . . .
Preparing the Mounting Surface
Feeding the Cables . . . . . . .
Mounting the Camera . . . . . . . .
Connecting the Cables . . . . . . . .
Power . . . . . . . . . . . . . .
Network . . . . . . . . . . . . .
Adjusting the Camera . . . . . . . .
Restoring Factory Defaults . . .
Completing the Installation . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
19
19
20
21
21
22
22
24
24
24
25
25
27
27
3
Installing the Honeywell IP Utility . . . . . . . . . . . . . .
About the Honeywell IP Utility . . . . . . . . . . . . . . . . . .
Installing the Honeywell IP Utility. . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . .
Installing the IP Utility . . . . . . . . . . . . . . . . . . . .
Connecting to a Camera . . . . . . . . . . . . . . . . . . . . .
Configuring the Camera’s IP Network Settings . . . . . . . . .
Changing the Camera’s Password . . . . . . . . . . . . . . . .
Using an ONVIF IP Device with a Network Video Recorder . . .
Uninstalling the Honeywell IP Utility . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
29
29
31
31
31
33
34
36
37
37
4
Setting Up the Camera . . . . . . . . . . . . . . . . . . . .
About the Web Client . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . .
Preparing for ActiveX Installation (Internet Explorer Only) .
Starting the Web Client . . . . . . . . . . . . . . . . . . . . . .
Viewing Live Video . . . . . . . . . . . . . . . . . . . . . . . .
Taking a Snapshot. . . . . . . . . . . . . . . . . . . . . .
Configuring Camera Settings . . . . . . . . . . . . . . . . . .
Basic Camera Setup Process . . . . . . . . . . . . . . . .
Setting Auto Exposure. . . . . . . . . . . . . . . . . . . .
Setting Day/Night and IR . . . . . . . . . . . . . . . . . .
Setting White Balance . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
39
39
40
40
44
47
47
48
49
50
51
52
.
.
.
.
.
.
.
.
.
.
.
.
.
.
800-12606 - A - 03/2013
10 | H4D1FR1(X) User Guide
Configuring Compression Settings . . . . . . . . . . . . . . . . . .
Configuring Priority Settings. . . . . . . . . . . . . . . . . . . .
Configuring Video Analytics . . . . . . . . . . . . . . . . . . . . . .
Setting Tamper Detection . . . . . . . . . . . . . . . . . . . . .
Setting Video Motion Detection (VMD) . . . . . . . . . . . . . .
Configuring Date and Time. . . . . . . . . . . . . . . . . . . . . . .
Setting the Time Zone . . . . . . . . . . . . . . . . . . . . . . .
Setting the Network Time Protocol (NTP) Server . . . . . . . . .
Overlay Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Port Allocation . . . . . . . . . . . . . . . . . . . . .
Setting the Snapshot File Type and Path (Internet Explorer Only)
Resetting and Rebooting the Camera. . . . . . . . . . . . . . .
Viewing Device Information . . . . . . . . . . . . . . . . . . . . . .
Logging Out of the Web Client . . . . . . . . . . . . . . . . . . . . .
Uninstalling Honeywell ONVIF ActiveX (Internet Explorer) . . . . . .
Uninstalling VLC Media Player (Chrome and Firefox) . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
52
55
57
58
59
64
64
64
69
70
71
71
72
72
73
73
74
A
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
B
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
www.honeywellvideo.com
Figures | 11
Figures
Figure 2-1
1
Removing the Gimbal from the Camera Base. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 2-2
Tracing the Camera Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 2-3
Conduit Holes on Camera Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 2-4
Camera Interface Board Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 2-5
Camera Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2-6
Final Focus Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 3-1
Overview of Honeywell IP Utility User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 3-2
IP Utility Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 3-3
ONVIF Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 3-4
IP Network Settings Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 3-5
Camera Password Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 4-1
Windows Firewall Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 4-2
Preferred UAC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 4-3
Run IE as Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 4-4
Trusted Sites Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 4-5
Adding a Subnet to Trusted Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 4-6
Allowing IE through the Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 4-7
Live View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 4-8
Camera Setup View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 4-9
Compression Setup View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 4-10
Codec Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 4-11
Primary Stream Settings (H.264) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 4-12
Secondary Stream Settings (H.264 or MJPEG) . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 4-13
Video Analytics View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 4-14
Video Analytics Alarm Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 4-15
VMD Configuration (Low Motion Threshold - 30%) . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 4-16
VMD Configuration (Medium Motion Threshold - 50%) . . . . . . . . . . . . . . . . . . . . . . 62
Figure 4-17
VMD Configuration (High Motion Threshold - 80%). . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 4-18
VMD Configuration - Combination Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 4-19
Date and Time View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 4-20
System Setup View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 4-21
Device Information View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 4-22
IP and Firmware Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
800-12606 - A - 03/2013
12 | H4D1FR1(X) User Guide
www.honeywellvideo.com
Tables | 13
Tables
Table 2-1
1
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 3-1
IP Network Settings Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 4-1
Default Camera User Names and Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 4-2
Auto Exposure Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 4-3
Day/Night Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 4-4
White Balance Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 4-5
Video Stream Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 4-6
Compression Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4-7
Priority Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 4-8
Range of User-Definable Bit Rate Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
800-12606 - A - 03/2013
14 | H4D1FR1(X) User Guide
www.honeywellvideo.com
About This Document
This document contains instructions for installing, configuring, and operating the Honeywell
equIP® Series H4D1FR1(X) network camera.
This document is intended for system installers, administrators, and operators.
Overview of Contents
This document contains the following chapters and appendixes:
•
Chapter 1, Introduction, introduces the H4D1FR1(X).
•
Chapter 2, Installing the Camera, describes how to mount the camera, connect the cables,
and adjust the camera’s field of view.
•
Chapter 3, Installing the Honeywell IP Utility, describes how to install the Honeywell IP
Utility, connect to a network camera, configure the camera’s IP network settings, and
change the camera’s password.
•
Chapter 4, Setting Up the Camera, describes how to configure camera settings using the
web client.
•
Appendix A, Troubleshooting, lists solutions to problems encountered during installation.
•
Appendix B, Specifications, lists the specifications of the H4D1FR1(X).
800-12606 - A - 03/2013
16 | H4D1FR1(X) User Guide
Related Documents
For more information, please refer to the following documents:
Document title
Part number
Description
equIP® Series H4D1FR1(X) 720p TDN Rugged Network
IR Minidome Camera Quick Installation Guide
800-12607V1
Installation guide
Typographical Conventions
This document uses the following typographical conventions:
Font
What it represents
Example
Helvetica
Keys on the keyboard
Press Ctrl+C
Lucida
Values of editable fields that are mentioned in the
The Time from field can be set to
body text of the document for reference purposes,
Hours:Minute:Seconds.
but do not need to be entered as part of a procedure
Text strings displayed on the screen
The message Unauthorized displays.
Syntax
(object) entered
Swiss721 BT Bold Words or characters that you must type. The word
“enter” is used if you must type text and then press
the Enter or Return key.
Italic
Enter the password.
Menu titles and other items you select
Double-click Open from the File menu.
Buttons you click to perform actions
Click Exit to close the program.
Placeholders: words that vary depending on the
situation
Enter your user name.
Cross-reference to external source
Refer to the System Administrator Guide.
Cross-reference within document
See Chapter 2, Installation.
www.honeywellvideo.com
1
Introduction
1
Honeywell’s ONVIF IR H4D1FR1(X) IP network camera provides high quality video surveillance
over a network connection.
Features
•
Outstanding image quality, 720p (1280 x 720) HD resolution
•
30 fps (25 fps PAL) progressive scan
•
True day/night, 3.3–12 mm VFAI lens with removable IR cut filter
•
24 LEDs provide up to 50 ft (15 m) of illumination, depending on scene reflectance
•
Camera tamper detection
•
Video motion detection
•
NTP time synchronization support
•
ONVIF support (Profile S)
•
Programmable daylight threshold settings to deliver color or black-and-white images.
•
Dual digital video streams, independently configurable, H.264 and/or H.264/MJPEG
•
Remote firmware updates
•
Supports both dynamic and static IP addresses
•
Date and time stamp embedded in video stream
•
Multiple browser support (Microsoft Internet Explorer, Google Chrome, Mozilla Firefox)
•
Advanced IP Utility software for easy system setup
•
Embedded web server for remote setup of camera video and network parameters
•
Choice of 24 V AC or Power over Ethernet (IEEE 802.3af) power inputs
•
Impact-resistant polycarbonate dome cover
•
IP66 ingress protection rating
•
Single model for surface mount and recessed ceiling applications
•
Wall and pendant mount kits available
800-12606 - A - 03/2013
18 | H4D1FR1(X) User Guide
www.honeywellvideo.com
2
Installing the Camera
2
This chapter describes how to:
•
Mount the camera (page 21)
•
Connect the cables (page 24)
•
Adjust the camera for the clearest image (page 25)
Before You Begin
Check that the items received match those listed on the order form and packing slip. Your
camera packing box should include the following items:
Table 2-1
Qty
1
1
Parts List
Item
Camera unit
Mounting kit:
• M5×40 screws (3)
• Rubber washers (3)
1
• Screw anchors (3)
• Allen keys (2)
Wiring kit:
• Power connector (1)
• BNC connector (1)
• M4×7 screws (2)
• Cable clamps (2)
1
Mounting template
1
Rubber gasket
1
Software DVD (includes user guide)
1
Quick installation guide (800-12607V1)
1
Product warranty
If any parts are missing or damaged, contact the dealer you purchased the camera from or call
Honeywell Customer Service.
800-12606 - A - 03/2013
20 | H4D1FR1(X) User Guide
Parts of the Camera
Conduit plug
Base
Rear conduit entry
Side conduit entry
Camera interface board
Gimbal ring
Gimbal assembly
Gasket
Captive screw
Dome cover
www.honeywellvideo.com
Installing the Camera | 21
Preparing to Mount the Camera
Preparing the Camera
1.
Using the supplied Allen key, loosen the three captive screws on the dome cover, and
then remove the dome cover and set it aside.
2.
Release the gimbal assembly from camera base.
To release the gimbal assembly, push down on the gimbal ring with two fingers (see
Figure 2-1) and pull back to slide the gimbal leg supports out of the black clips on the
camera base.
Figure 2-1
Removing the Gimbal from the Camera Base
Push down on gimbal ring and pull back
Black clips (×4)
3.
Carefully lift the gimbal assembly away from the camera base to expose the camera
interface board connections and the mounting holes.
CAUTION
When moving the gimbal, make sure that you do not
pull and over-stress the two ribbon cables.
800-12606 - A - 03/2013
22 | H4D1FR1(X) User Guide
Preparing the Mounting Surface
1.
Note
The housing should be mounted on a flat surface only.
Note
To prevent moisture from entering the housing, position the camera base with the
side conduit entry pointing down if you are mounting the camera on a wall or
other vertical surface.
Use the supplied mounting template to mark the screw and access cable holes on the
mounting surface.
Alternatively, place the camera base against the mounting surface and trace the screw
holes (see Figure 2-2).
Figure 2-2
2.
Tracing the Camera Base
Pre-drill holes in the mounting surface, as required.
Feeding the Cables
There are two conduit entry points on the camera base: one at the rear and one on the side. The
camera ships with the conduit plug pre-installed in the rear conduit entry.
www.honeywellvideo.com
Installing the Camera | 23
Figure 2-3
Conduit Holes on Camera Base
Rear conduit entry
Camera base
Conduit plug
locking screw
Side conduit
entry
Conduit plug
To use the rear conduit entry
1.
Unscrew the conduit plug from the rear conduit entry (see Figure 2-3).
2.
Loosen the locking screw over the side conduit entry, install the conduit plug in the side
conduit entry, and then re-tighten the locking screw to secure the conduit plug in place.
3.
Follow these steps:
If conduit is used (recommended)
If conduit is not used
1. Insert the conduit into the
rear conduit entry.
1. Install the supplied rubber gasket on
the camera base with the "+"
positioned over the rear conduit entry.
2. Apply sealant around the conduit entry
to prevent moisture from entering the 2. Make a slit in the gasket over the "+".
housing.
3. Feed the cables through the slit.
4. Apply sealant around the gasket to
prevent moisture from entering the
housing.
To use the side conduit entry
1.
Loosen the locking screw over the side conduit entry (see Figure 2-3), insert the conduit,
and then re-tighten the locking screw to secure the conduit in place.
2. Apply sealant around the conduit entry to prevent moisture from entering the housing.
800-12606 - A - 03/2013
24 | H4D1FR1(X) User Guide
Mounting the Camera
To mount the camera
1.
Route the cables through your chosen conduit entry (see Feeding the Cables on page 22).
2.
Mount the camera to a wall or ceiling using the supplied mounting screws.
If you are using screws other than those supplied by Honeywell, remove the rubber
washers from the Honeywell-supplied screws and install them under the head of each
screw.
3.
Apply an appropriate sealant around the mounting screws to prevent moisture from
entering the camera enclosure.
Connecting the Cables
Power
CAUTION
24 V AC models require the use of CSA Certified/UL
Listed Class 2 power adapters to ensure compliance with electrical
safety standards. Power over Ethernet (PoE) should meet the IEEE
802.3af PoE standard.
You can use either a 24 V AC source or Power over Ethernet (48 V DC) to power the camera.
Do not connect both power sources at the same time. A green light-emitting diode (LED) on
the camera interface board illuminates when the camera is receiving power.
To connect the power
•
For 24 V AC connection, connect the power wires to the supplied two-pin green connector
and plug the connector into the 24 V AC terminal block on the camera interface board
(see Figure 2-4).
•
For PoE connection, connect a Category 5/5e Ethernet cable to the RJ45 jack on the
camera interface board (see Figure 2-4).
www.honeywellvideo.com
Installing the Camera | 25
Figure 2-4
Camera Interface Board Connections
RJ45 Ethernet
connection
(PoE/network)
J3
24 V AC power
connection
J9
Network
To connect to the network
•
Connect a Category 5/5e Ethernet cable (10BaseT/100BaseTX) to the RJ45 jack on the
camera interface board (see Figure 2-4) if you have not already done so.
Adjusting the Camera
You can adjust the camera field of view locally at the camera using a spot monitor.
To adjust the field of view
1.
Verify that power is being supplied to the camera (the green LED on the camera interface
board should be illuminated).
2.
Reinstall the gimbal assembly on the camera base.
3.
Using the supplied video cable, connect the local video out connector on the camera
interface board to the video input connector on your spot monitor.
Note
It will take approximately 60 seconds after connecting to a power source for video
to appear on the spot monitor.
800-12606 - A - 03/2013
26 | H4D1FR1(X) User Guide
4.
Loosen the adjustment screws that lock the gimbal assembly in place to adjust the pan
and tilt rotation (see Figure 2-5).
5.
Adjust the gimbal assembly (pan, tilt, focus, and zoom) to achieve the desired view.
CAUTION
Adjust the camera field of view only by moving the
gimbal assembly. Do not move the camera lens to adjust the camera
field of view as this might result in irreparable damage.
Note
When aiming the camera, rotate the IR LED board so that the LEDs are not
obstructed by the dome cover.
Figure 2-5
Camera Adjustment
Legend
Loosen locking screw to
adjust pan rotation.
Set Focus (top)
A = Pan-rotation (360°)
B = Horizontal rotation (360°)
C = Tilt rotation (75°)
D = IR board rotation (360°)
Local video out
Set Zoom (bottom)
A
Reset button
B
Loosen locking screw
to adjust tilt rotation.
6.
www.honeywellvideo.com
Retighten the adjustment screws to lock the gimbal assembly in place.
D
C
Installing the Camera | 27
7.
If necessary, refocus the lens. Hold the dome cover in front of the lens (see Figure 2-6)
when adjusting the focus (remove the protective film from the bubble first).
Figure 2-6
8.
Final Focus Adjustment
Disconnect the supplied video cable from the local video out connector on the camera
interface board.
Restoring Factory Defaults
You can restore the camera options and passwords to their default settings by pressing the
reset button located on the camera interface board (see Figure 2-5). Use a pin or straightened
paper clip to press the reset button and hold for five seconds.
Completing the Installation
1.
Replace the dome cover on the camera base and securely tighten the captive screws.
2.
Remove the protective film from the bubble if you have not already done so.
800-12606 - A - 03/2013
28 | H4D1FR1(X) User Guide
www.honeywellvideo.com
3
Installing the Honeywell IP Utility
3
This chapter describes how to:
•
Install the IP Utility (page 31)
•
Connect to a H4D1FR1(X) camera (page 33)
•
Configure the camera’s network settings (page 34)
•
Change the camera’s password (page 36)
•
Uninstall the IP Utility (page 37)
About the Honeywell IP Utility
The Honeywell IP Utility is a software application used to discover and configure equIP Series
and Performance Series products residing on an IP network. Using the IP Utility, you can
change your H4D1FR1(X) camera’s network settings (including device name), upgrade the
camera’s firmware, and manage the camera’s user settings. You can also use the utility to
launch a web client application in your browser that lets you view live video and access
additional camera configuration settings.
For an overview of the Honeywell IP Utility interface, see Figure 3-1.
800-12606 - A - 03/2013
30 | H4D1FR1(X) User Guide
Figure 3-1
Overview of Honeywell IP Utility User Interface
Refresh button
Connect button
Disconnect button
Limited/No connectivity
button
Use the Product Filter drop-down
menu to select a specific device,
such as all H3D1F cameras.
The About menu displays the
software version installed.
From the User tab, Administrators
can change the web client user
passwords.
The Discovery pane lists
the IP devices found on the
network and groups by
device type.
Use Batch Firmware Upgrade
to select a group of devices and
upgrade the firmware for all.
www.honeywellvideo.com
The Status bar displays how many
devices are on the network, which
one you are connected to, and
which user is logged on.
Installing the Honeywell IP Utility | 31
Installing the Honeywell IP Utility
You can install the IP Utility from the DVD that came with your camera or you can download the
latest version from Honeywell’s Download Center (recommended):
http://www.honeywellsystems.com/support/download-center/index.html
To receive a user name and password for accessing the Download Center, contact the
customer service center within your region. This information is provided on the Download
Center webpage.
Note
If you have an older version of Honeywell IP Utility installed on your computer you
may need to uninstall it before you can install the new version. For instructions on
how to uninstall the IP Utility, see Uninstalling the Honeywell IP Utility on page 37.
Before You Begin
Before you begin installing the IP Utility, do the following:
1.
Ensure that your workstation meets the following system requirements:
Operating System
Windows XP Professional, SP3
Windows Server 2003 R2 (32 bit)
Windows Vista, SP1
Windows 7 (32/64 bit)
Windows Server 2008 R2 (64 bit)
CPU
Pentium 4, 3.1 GHz or faster
System Memory
1 GB (32 bit) or 2 GB (64 bit)
2.
Ensure that you have Windows administrator privileges for the workstation on which you
are installing the IP Utility.
3.
Confirm that your camera is connected to the network (see Connecting the Cables on
page 24).
Installing the IP Utility
The IP Utility is installed on your workstation using InstallShield. When you install the IP Utility,
a networking protocol (Bonjour) is also installed that enables the automatic discovery of IP
network devices.
800-12606 - A - 03/2013
32 | H4D1FR1(X) User Guide
To install the IP Utility
1.
Close any open applications. If you are using Norton AntiVirus software, disable it.
2.
Do one of the following:
Install from DVD
Install from Website
•
1. Go to www.honeywellsystems.com/
support/download-center/index.html.
Insert the DVD that was shipped with
your camera into your workstation’s
DVD-ROM drive.
If the InstallShield wizard does not
open automatically, browse to [DVD
drive]\Honeywell_IP_Utility\ and
double-click Honeywell_IP_Utility_
Setup.exe.
4.
5.
2. Follow the instructions on the page to
log in and find your camera.
3. Run the InstallShield wizard.
Follow the InstallShield wizard’s on-screen instructions to complete the installation.
Open the IP Utility by double-clicking the Honeywell IP Utility icon
The IP Utility opens on your desktop (see Figure 3-2).
Figure 3-2
www.honeywellvideo.com
IP Utility Main Screen
on the desktop.
Installing the Honeywell IP Utility | 33
Connecting to a Camera
When you open the IP Utility, the devices on the network—including devices on other
subnets—are automatically discovered and listed in the Discovery pane on the left of the
screen. After the initial discovery, the list of discovered devices auto-refreshes at regular
intervals. You can manually refresh the list by clicking
(Refresh).
To connect to a network camera
•
In the Discovery pane, double-click the camera you want to connect to. Alternatively, click
the camera name, and then click
(Connect).
When connecting to an ONVIF camera for the first time, the ONVIF credentials login
window appears (see Figure 3-3). Enter your user name and password, and then click OK.
Figure 3-3
ONVIF Login Window
If the connection is successful, the message Connected to Device [device name]
appears in the status bar at the bottom of the screen.
If the connection is unsuccessful,
(Limited/No Connectivity) replaces
(Connect) in the
Discovery pane. Check the the network settings of the camera and the workstation. The camera
must be on the same subnet as the workstation. Contact your network administrator if you
require additional support.
To disconnect from a network camera
•
In the Discovery pane, click the camera you want to disconnect from, and then click
(Disconnect).
If you try to disconnect without saving configuration details, you will be prompted to save
your changes. Click Yes to save the changes and disconnect. Click Cancel to discard the
changes and disconnect.
800-12606 - A - 03/2013
34 | H4D1FR1(X) User Guide
Configuring the Camera’s IP Network Settings
You can configure a connected camera’s IP network settings either automatically or manually
using the IP Utility. Contact your network administrator if you experience any network-related
issues or if you have questions about your network.
Table 3-1
IP Network Settings Options
Option
Description
Device Name
By default, the device name is the device type plus the MAC address. For
security purposes it is recommended that you change the device name.
MAC Address
A unique address assigned to the device in the factory. Not configurable.
IP Address
The IP address of the device on the network. The camera can be assigned a
static or a dynamic IP address. A static IP address is assigned by the user. A
dynamic IP address is assigned automatically by a DHCP or APIPA service.
Subnet Mask
The subnet mask, or netmask, value of the device on the network. IP networks
can be subdivided into a series of smaller networks called subnets. When a
network is subnetted, the subnet mask specifies which smaller network (subnet)
the device belongs to. If the subnet mask is incorrect, the camera cannot
communicate with other devices on the network.
Default Gateway
The default gateway address that connects the device to the network. The
gateway allows communication between devices on different networks. If the
gateway is incorrect, the camera cannot communicate with other devices that
are not in the same network address range.
To configure the camera’s network settings automatically
1.
Connect to the camera (see Connecting to a Camera on page 33).
2.
In the System tab, under IP Network Settings, confirm that the Obtain an IP address
automatically check box is selected.
3.
Enter a descriptive name for the camera in the Device Name field. For example,
FrontLobbyDome01. (By default, the device name is the device type plus the MAC
address.)
4.
Click Apply to save the changes.
The network automatically assigns the IP address based on the DHCP network server
details. If no DHCP server is present on the network, the camera defaults to an APIPA
address (169.254.x.x).
To configure the camera’s network settings manually
1.
Connect to the camera (see Connecting to a Camera on page 33).
2.
In the System tab, under IP Network Settings, clear the Obtain an IP Address
automatically check box.
www.honeywellvideo.com
Installing the Honeywell IP Utility | 35
Figure 3-4
IP Network Settings Configuration
3.
Enter a descriptive name for the camera in the Device Name field. For example,
FrontLobbyDome01. (By default, the device name is the device type plus the MAC
address.)
4.
Enter values for the IP Address, Subnet Mask, and Default Gateway (see Table 3-1).
The MAC address is a factory-assigned address and is not configurable.
Note
The IP address of the camera must be in the same range as the IP address of the
workstation. For example, if the workstation’s IP address is 192.168.1.xx, the
camera’s IP address should start with 192.168.1 (as in 192.168.1.xy).
CAUTION
Confirm the network settings before clicking Apply.
Incorrect values may prevent the IP Utility from connecting to the device.
5.
Click Apply to save the changes.
The network settings are updated and a message confirming the change appears in the
status bar at the bottom of the screen.
800-12606 - A - 03/2013
36 | H4D1FR1(X) User Guide
Changing the Camera’s Password
You can change a connected camera’s administrator (admin) or guest password using the IP
Utility.
To change the camera administrator or guest password
1.
Connect to the camera (see Connecting to a Camera on page 33).
2.
Click the Users tab.
Figure 3-5
Camera Password Configuration
3.
In the User Name field, select admin or guest.
4.
In the Old Password field, type the old password.
5.
In the New Password field, type the new password.
6.
In the Verify Password field, type the new password again.
7.
Click Apply to save the changes.
www.honeywellvideo.com
Installing the Honeywell IP Utility | 37
Using an ONVIF IP Device with a Network Video Recorder
Your camera features ONVIF support and open API for software integration. Refer to
www.onvif.org for the ONVIF specification and to the Honeywell Open Technology Alliance
website at www.security.honeywell.com/hota/ to learn more about our open and integrated
solutions. There is no support for legacy equIP and equIP2 protocols.
For additional information, refer to the documentation supplied with your NVR or contact your
NVR network administrator.
Uninstalling the Honeywell IP Utility
To uninstall the IP Utility in Windows 7
1.
Click the Start button, click Control Panel, click Programs, and then click Programs and
Features.
2.
Click Honeywell IP Utility, and then click Uninstall.
If you are prompted to confirm that you want to uninstall Honeywell IP Utility, click Yes.
To uninstall the IP Utility in Windows XP
1.
Click Start, click Control Panel, and then double-click Add or Remove Programs.
2.
Click Honeywell IP Utility, and then click Remove.
3.
You are prompted to confirm that you want to uninstall Honeywell IP Utility. Click Yes.
800-12606 - A - 03/2013
38 | H4D1FR1(X) User Guide
www.honeywellvideo.com
4
Setting Up the Camera
4
This chapter describes how to:
•
Start the web client (page 44)
•
View live video (page 47)
•
Configure camera setup, including IR settings (page 48)
•
Configure camera compression settings (page 48)
•
Configure camera tamper detection and motion detection settings (page 57)
•
Configure camera date and time settings (page 64)
•
Reset the camera to factory default settings (page 70)
•
View camera network settings and firmware details (page 72)
About the Web Client
The web client is an Internet-based application that enables administrators to monitor live video
and make adjustments to the camera setup.
Guest users can monitor live video but cannot access the setup functionality of the web client.
The camera’s default user names and passwords are listed in Table 4-1. To change the
administrator or guest password, see Changing the Camera’s Password on page 36.
Table 4-1
Default Camera User Names and Passwords
Login Profile
User Name
Password
Administrator
admin
1234
Guest
guest
guest
800-12606 - A - 03/2013
40 | H4D1FR1(X) User Guide
Before You Begin
You must have Windows administrator privileges and your workstation must meet the following
minimum requirements to run the web client application.
Operating System
Windows XP Professional, SP3
Windows Server 2003 R2 (32 bit)
Windows Vista, SP1
Windows 7 (32/64 bit)
Windows Server 2008 R2 (64 bit)
CPU
Pentium 4, 3.1 GHz or faster
System Memory
1 GB (32 bit) or 2 GB (64 bit)
Graphics Card
Display driver with Direct3D enabled (for Internet Explorer only)
Web Browser
Microsoft Internet Explorer 8 or 9 (32 bit)
Google Chrome v23.0.1271.97 or later (32 bit)
Mozilla Firefox v17.01 or later
Preparing for ActiveX Installation (Internet Explorer Only)
Configuring Windows 7 (32 bit/64 bit) and IE Security Settings
Note
Make sure your Windows user account has administrator privileges.
Configure Windows Firewall
1.
Click Start  Control Panel  System and Security  Windows Firewall Settings.
The Windows Firewall Settings page opens.
Figure 4-1
2.
Windows Firewall Settings
Click Allow a program or feature through Windows Firewall.
The Allowed Programs list appears.
www.honeywellvideo.com
Setting Up the Camera | 41
3.
Do one of the following:
•
If Internet Explorer is already in the Allowed list, then select all the check boxes
(Domain, Home/Work, Public, Group Policy).
•
If Internet Explorer is not already in the Allowed list, click Allow another program,
browse for iexplore, and then click Open. Once in the Allowed list, select all the
check boxes (Domain, Home/Work, Public, Group Policy).
Configure User Account Control (UAC) Settings
1.
Click Start  Control Panel.
2.
In the Search Control Panel, type UAC.
3.
Click Change User Account Control settings.
The User Account Control Settings page appears.
Figure 4-2
Preferred UAC Settings
If the UAC level is not configured to the lowest level, then please run Internet Explorer as
administrator. Click Start, right-click Internet Explorer, and then click Run as administrator.
Figure 4-3
Run IE as Administrator
800-12606 - A - 03/2013
42 | H4D1FR1(X) User Guide
Add Camera URL to Trusted Sites in Internet Explorer
1.
Open the Honeywell IP Utility.
2.
Connect to your camera.
3.
Click Launch Browser to open the camera login page.
4.
In the browser, click Tools  Internet Options  Security  Trusted Sites.
Figure 4-4
Trusted Sites Configuration Page
5.
Click Sites. The Trusted Sites window opens.
6.
Clear the Require server verification (https:) for all sites in the zone check box.
7.
Do one of the following:
www.honeywellvideo.com
•
To add one camera to the Trusted Sites list, enter the URL in the Add this website to
the zone: field.
•
To add a whole subnet to the Trusted Sites list, enter the partial URL with a * at the
end in the Add this website to the zone: field. Use a * to add the whole network.
Setting Up the Camera | 43
Figure 4-5
8.
Adding a Subnet to Trusted Sites
Click Add to add the website to the list of trusted websites, and then click Close.
Configuring Windows XP SP3 and IE Security Settings
Note
Make sure your Windows user account has administrator privileges.
Configure Windows Firewall
1.
Click Start, click Control Panel, and then double-click Windows Firewall.
2.
Click the Exceptions tab.
3.
If the firewall is on, configure it to allow IE through the firewall, and then click OK to save
the changes.
Figure 4-6
Allowing IE through the Firewall
Add Camera URL to Trusted Sites in Internet Explorer
See Add Camera URL to Trusted Sites in Internet Explorer on page 42.
800-12606 - A - 03/2013
44 | H4D1FR1(X) User Guide
Starting the Web Client
To start the web client in Internet Explorer
1.
Open the Honeywell IP Utility.
2.
Connect to your camera.
3.
Click Launch Browser.
Connect to the device,
and then click Launch
Browser.
Alternatively, you can enter the IP address of the camera directly into the address bar of
the browser.
The login window is displayed.
4.
In the Username field, select admin.
5.
In the Password field, type the default admin login password 1234, and then click Login.
www.honeywellvideo.com
Setting Up the Camera | 45
The first time you open the web client you will be prompted to install Honeywell ONVIF
ActiveX® on your computer.
If a previous version of Honeywell ActiveX is installed, you will be prompted to upgrade.
Follow the on-screen instructions to install the ActiveX control.
Note
You may need to disable your firewall to install Honeywell ONVIF ActiveX on your
computer. You will need Windows administrator privileges to do this.
The web client application opens and live video is displayed in your browser.
To start the web client in Chrome or Firefox
1.
Install VLC media player from the installation DVD that was shipped with your camera.
Note
It is strongly recommended that you install VLC media player from the supplied
installation DVD rather than from the Web.
800-12606 - A - 03/2013
46 | H4D1FR1(X) User Guide
2.
Follow the on-screen instructions to install the VLC player. Select Full installation.
3.
Open your browser.
Note
4.
You may need to restart Firefox after installing VLC media player.
Type the IP address of the camera (listed in the IP Utility) in the address bar of the
browser, and then press Enter.
The login window is displayed.
5.
In the Username field, select admin.
6.
In the Password field, type the default admin login password 1234, and then click Login.
The web client application opens and live video is displayed in your browser.
If VLC media player is not installed, the following warning message will appear:
www.honeywellvideo.com
Setting Up the Camera | 47
Viewing Live Video
Live view (Figure 4-7) displays live real-time video from the selected camera.
Figure 4-7
Live View
Taking a Snapshot
The Snapshot
function lets you save an image from Live view to a default folder on your
computer (for example, C:\Documents and Settings\User\My Documents\Honeywell Video
Systems\Snapshot). Files are saved as: DeviceName_Date_Time.jpg.
The Snapshot function is available to both administrators and guests.
To take a snapshot in Microsoft Internet Explorer 8 and 9
•
Click the Snapshot button
.
A message appears confirming that the snapshot was saved successfully.
800-12606 - A - 03/2013
48 | H4D1FR1(X) User Guide
Note
To configure the settings for Snapshot, including the file type and save path, see
System Setup on page 70.
To take a snapshot in Google Chrome and Mozilla Firefox
1.
Click the Snapshot button
.
A window opens displaying the snapshot (your browser must be configured to allow
pop-ups).
Chrome
Firefox
2.
Right-click the window, and then click Save Image As.
3.
In the Save Picture dialog box, browse to the folder where you want to save the file, enter
a file name, and then click Save.
Configuring Camera Settings
The Camera Setup view (Figure 4-8) lets you configure auto exposure, day/night operation, and
white balance for both primary and secondary video streams.
www.honeywellvideo.com
Setting Up the Camera | 49
Figure 4-8
Camera Setup View
Basic Camera Setup Process
1.
Aim and focus the camera locally (see Adjusting the Camera on page 25).
2.
Create a typical scene. Add the motion, scene complexity, and lighting levels (day or
night) expected in normal operation.
3.
Log in to the web client, and then click Setup.
4.
Click Camera Setup, and then adjust the image parameters under Auto Exposure,
Day/Night, and White Balance to achieve the desired exposure and white balance.
5.
Click Compression Setup, and then select the Statistics check box at the bottom of the
screen (available in Internet Explorer only).
6.
In Compression Setup, under Primary, set the resolution, frame rate, and priority mode
(Quality, Bit Rate, or Frame Rate).
7.
Is the delivered picture quality, bit rate, and frame rate acceptable with the appropriate
motion, scene complexity, and day/night transitions?
•
Yes - Camera setup is complete.
•
No - Additional configuration is required (see below).
If the delivered bit rate is close to the
maximum bit rate, can you increase the
maximum bit rate value?
Yes - Increase the
maximum bit rate.
No - Set the compression
ratio to High or Maximum.
Can you increase the target bit rate value?
Yes - Increase the
target bit rate.
No - Reduce the resolution
and/ or frame rate.
800-12606 - A - 03/2013
50 | H4D1FR1(X) User Guide
Setting Auto Exposure
To configure Auto Exposure settings, see Table 4-2. Click Apply to save your changes.
Table 4-2
Auto Exposure Settings
Setting
Options
ALC (Automatic
Level 1–25
Light Compensation)
Description
The shutter speed is constant and brightness is controlled
through the lens iris by opening and closing it.
Adjust the ALC level so that the image is correctly exposed
(neither too bright nor too dark). Recommended for indoor
scenes, especially under fluorescent light.
ELC (Electronic Light
Compensation)
Level 1–25
The lens iris is fully open at all times and brightness is achieved
by controlling the electronic shutter.
Adjust the ELC level to attain the desired scene brightness.
Recommended for outdoor scenes.
AGC (Automatic
Gain Control)
Off, 20 dB,
30 dB, 40 dB
Default is 30 dB. Increase the gain setting to increase the scene
brightness.
Note
As AGC levels are reduced, the threshold ranges for
Day-to-Night and Night-to-Day are decreased.
DSS (Digital Slow
Shutter)
Disable, Low,
High
Automatically provides a clear image under low-light conditions
by increasing scene brightness. However, motion blur may
result. The higher the setting, the likelier motion blur will occur.
Flickerless
[Enabled],
[Disabled]
Eliminates flickering caused by certain lighting conditions (such
as fluorescent lighting).
Note
DNR (Digital Noise
Reduction)
[Enabled],
[Disabled]
DNR improves the picture quality in low light by reducing video
noise.
Note
www.honeywellvideo.com
Flickerless is unavailable when ELC is selected.
DNR is unavailable when AGC is set to Off.
Setting Up the Camera | 51
Setting Day/Night and IR
To configure Day/Night settings, see Table 4-3. Click Apply to save your changes.
Table 4-3
Day/Night Settings
Setting
Options
Description
Day/Night
Auto, Day,
Night
Controls true day/night (TDN) operation.
B/W, Color
Sets the color mode to B/W (monochrome) or Color when in
Night mode.
Night Mode
When Auto is selected, the IR cut filter is removed automatically
in low-light scenes. When Day is selected, the IR cut filter is on at
all times. When Night is selected, the IR cut filter is off (removed)
at all times.
Day/Night must be set to Night.
Detect Time
5–60 seconds
Sets the time (5 to 60 seconds) before the camera switches to
Day or Night mode after detecting a low-light condition or a
normal light condition, respectively.
Day/Night must be set to Auto.
Day to Night
2–7
Determines the light detection level when the camera switches to
Night mode. The lower the value, the darker the lighting
conditions before the camera switches.
Day/Night must be set to Auto.
Night to Day
4–9
Note
The Day to Night threshold must be set at least 2 less
than the Night to Day threshold setting.
Note
The Day to Night threshold is decreased if the AGC level
is reduced.
Determines the light detection level when the camera switches to
Day mode. The higher the value, the brighter the lighting
conditions before the camera switches.
Day/Night must be set to Auto.
Note
IR Level
Off, Low,
Medium, High
Controls IR LED intensity. Select setting based on desired scene
illumination.
Note
Dynamic IR
Off, On
The Night to Day threshold is decreased if the AGC level
is reduced.
IR Level is unavailable when Day/Night is set to Day.
Controls overexposure. When set to On, the camera
automatically adjusts to minimize overexposure occurring from
reflective objects in the scene.
Note
Dynamic IR is unavailable when IR Level is set to Off.
800-12606 - A - 03/2013
52 | H4D1FR1(X) User Guide
Setting White Balance
To configure White Balance settings, see Table 4-4. Click Apply to save your changes.
Table 4-4
White Balance Settings
Setting
Options
Description
WB Control
Auto, Manual,
WBC Push
Auto adjusts white balance automatically. Recommended for
environments with changing lighting conditions.
Manual allows user to set red and blue gain manually.
WBC Push optimizes white balance for a given scene. Click
Lock to lock the setting. Recommended for environments with
constant lighting conditions.
R Gain (0–255)
0–255
When WB Control is set to Manual, red gain is selectable from
0 to 255.
B Gain (0–255)
0–255
When WB Control is set to Manual, blue gain is selectable from
0 to 255.
Configuring Compression Settings
The Compression Setup view (Figure 4-9) lets you configure the way video is displayed in the
web client.
Figure 4-9
www.honeywellvideo.com
Compression Setup View
Setting Up the Camera | 53
The camera supports two simultaneous video streams. The primary stream delivers
H.264-compressed video.The secondary stream delivers either H.264 or MJPEG-compressed
video (see Table 4-5).
Table 4-5
Video Stream Configurations
Codec Type
Description
H.264
H.264 compression used for primary stream; no secondary stream
H.264 + H.264
H.264 compression used for primary and secondary stream
H.264 + MJPEG
H.264 compression used for primary stream and MJPEG compression used for
secondary stream
You can configure the settings for the primary stream (Figure 4-11) and/or the secondary stream
(Figure 4-12) based on the codec type you select (Figure 4-10).
Figure 4-10
Codec Type
Figure 4-11
Primary Stream Settings (H.264)
Default settings shown for NTSC models
Set the Resolution
Set the Frame Rate
Set the Priority to Quality, Bit Rate, or Frame Rate
Set the Compression Ratio
Set the Target Bit Rate
Set the Maximum Bit Rate (kbps)
Set the GOP (Group of Pictures)
Note
To configure the secondary stream, either H.264 + H.264 or H.264 + MJPEG
must be selected as the codec type.
800-12606 - A - 03/2013
54 | H4D1FR1(X) User Guide
Figure 4-12
Secondary Stream Settings (H.264 or MJPEG)
Default settings shown for NTSC models
Set the Resolution
Set the Frame Rate
Set the Priority to Quality or Bit Rate
Set the Compression Ratio
Set the Target Bit Rate
Set the Maximum Bit Rate (kbps)
Note
GOP is not available if you select
MJPEG for the secondary stream.
To configure the Primary and/or Secondary stream compression settings, see Table 4-6. Click
Apply to save your changes.
Note
Internet Explorer users only: Select the Statistics check box at the bottom of the
screen to view the received bit rate and received frame rate as you make changes.
Please note that the Statistics check box is disabled by default. To view the received
bit rate and frame rate, you must enable it each time you log on to the web client.
Table 4-6
Compression Settings
Setting
Options
Description
Resolution
Primary
1280×720
800×450
640×360
320×180
Frame Rate
1–30 (NTSC)
1–25 (PAL)
Priority
Primary
Quality,
Bit Rate,
Frame Rate
Compression
Ratio
Minimum, Low, Medium,
High, Maximum
Available when Priority is set to Quality.
Minimum provides the highest picture quality.
Maximum provides the lowest picture quality.
Target Bit Rate
250–7000 kbps
Available when Priority is set to Bit Rate or
Frame Rate. For more information, see
Configuring Priority Settings on page 55.
Sets the picture resolution.
Secondary
1280×720 (H.264)
800×450 (H.264)
640×360 (H.264)
320×180 (H.264)
640×360 (MJPEG)
320×180 (MJPEG)
The number of frames displayed per second.
Secondary
Quality,
Bit Rate
Sets whether picture quality, bit rate, or frame rate
has operational priority. For more information,
see Configuring Priority Settings on page 55.
Maximum Bit Rate 250–7000 kbps
Available when Priority is set to Quality. For
more information, see Configuring Priority
Settings on page 55.
GOP
Group of pictures. Not available on MJPEG
secondary stream.
www.honeywellvideo.com
1–50
Setting Up the Camera | 55
Configuring Priority Settings
Your camera uses efficient compression technology to provide a high quality picture using
minimal bandwidth. The default settings are based on typical user requirements and are
adequate for most scenes. However, scenes with higher than average motion may require
additional configuration.
About Priority Settings
For the primary stream, you can prioritize the picture quality, bit rate, or frame rate. For the
secondary stream, you can prioritize the picture quality or bit rate. These settings are described
in Table 4-7.
Table 4-7
Priority Settings
Priority
Bit Rate Type
Description
Quality
Maximum Bit Rate
The camera maintains the picture quality until the delivered bit rate
exceeds the Maximum Bit Rate, at which point the camera begins
to drop frames.
Bit Rate
Target Bit Rate
The camera adjusts the picture quality to achieve the Target Bit
Rate.
Frame Rate
Target Bit Rate
The camera maintains the selected frame rate while adjusting the
picture quality to meet the Target Bit Rate.
The range of user-definable bit rate values is dependent on the video stream, codec type, and
resolution (see Table 4-8).
Table 4-8
Stream
Primary
Range of User-Definable Bit Rate Values
Codec
Resolution
Range
H.264
1280×720
800×450
640×360
320×180
Between 1000 and 6000 kbps
Between 500 and 3000 kbps
Between 500 and 3000 kbps
Between 250 and 1500 kbps
H.264
1280×720
800×450
640×360
320×180
Between 1000 and 6000 kbps
Between 500 and 3000 kbps
Between 500 and 3000 kbps
Between 250 and 1500 kbps
MJPEG
640×360
320×180
Between 1000 and 7000 kbps
Between 500 and 3500 kbps
Secondary
800-12606 - A - 03/2013
56 | H4D1FR1(X) User Guide
Setting Quality as Priority
To set picture quality as the priority
1.
Next to Priority, select Quality.
2.
Next to Compression Ratio, select
Minimum, Low, Medium, High, or
Maximum.
The default setting is Medium. Selecting
Minimum or Low will increase the overall
picture quality and increase the delivered bit
rate.
3.
Next to Maximum Bit Rate, enter a value
between 250 and 7000 kbps (see Table 4-8).
If the delivered bit rate exceeds this value, the
frame rate will drop.
Setting Bit Rate as Priority
To set bit rate as the priority
1.
Next to Priority, select Bit Rate.
2.
Next to Target Bit Rate, enter a value
between 250 and 7000 kbps (see Table 4-8).
Increasing or decreasing the target bit rate
threshold will increase or decrease the
picture quality accordingly.
If the delivered bit rate exceeds this value, the
frame rate will drop.
Setting Frame Rate as Priority
(Primary Stream Only)
To set frame rate as the priority
1.
Next to Frame Rate, select the frame rate that
you want to maintain.
2.
Next to Priority, select Frame Rate.
3.
Next to Target Bit Rate, enter a value
between 250 and 7000 kbps (see Table 4-8).
Increasing or decreasing the target bit rate
threshold will increase or decrease the
picture quality accordingly.
This priority allows the actual bit rate to
fluctuate beyond the target bit rate while
maintaining the selected frame rate.
www.honeywellvideo.com
Setting Up the Camera | 57
Configuring Video Analytics
The Video Analytics view (Figure 4-13) lets you configure the camera’s tamper detection and
video motion detection settings.
Figure 4-13
Video Analytics View
Each setting has three threshold levels: high (80%), medium (50%), and low (30%). When these
thresholds are exceeded, camera sabotage or motion is detected and an alarm message
appears above the video display (Figure 4-14).
Figure 4-14
Note
Video Analytics Alarm Message
The Video Analytics screen shows a static video snapshot instead of live video.
For this reason, you should open a second web client window for monitoring live
video.
800-12606 - A - 03/2013
58 | H4D1FR1(X) User Guide
Setting Tamper Detection
The tamper detection settings alert the web client user to possible camera sabotage when the
following occurs:
•
The camera video is blurred.
•
The camera is blinded.
•
The camera field of view has changed.
To avoid false alarms, tamper detection should
be manually disabled when:
•
The video display is being configured.
•
Text is overlaid on the video.
•
The video display becomes too dark.
Blur Threshold
The video blurring may occur when the camera is exposed to rain or other elements or when
the lens focus is set incorrectly.
To set the blur threshold
1.
2.
Next to Blur Threshold, select one of the following options:
•
High (80%)
Maximum blurring detection. The alarm message appears
when the video is blurred by 80% or more.
•
Medium (50%)
Medium blurring detection. The alarm message appears
when the video is blurred by 50% or more.
•
Low (30%)
Minimum blurring detection. The alarm message appears
when the video is blurred by 30% or more.
•
Disable (Default)
Disables video blur detection.
Click Apply to save the settings.
Blinding Threshold
Camera blinding occurs when an obstacle is placed in front of the camera lens.
To set the blinding threshold
1.
2.
www.honeywellvideo.com
Next to Blinding Threshold, select one of the following options:
•
High (80%)
Maximum blinding detection. The alarm message appears
when the camera lens is blinded by 80% or more.
•
Medium (50%)
Medium blinding detection. The alarm message appears
when the camera lens is blinded by 50% or more.
•
Low (30%)
Minimum blinding detection. The alarm message appears
when the camera lens is blinded by 30% or more.
•
Disable (Default)
Disables camera blinding detection.
Click Apply to save the settings.
Setting Up the Camera | 59
Scene Change
Scene change detection works best detecting objects with distinct edges and corners. Scenes
that appear flat or monochrome may trigger false alarms.
To set the scene change threshold
1.
Click Reset Scene.
2.
Next to Scene Change, select one of the following options:
3.
•
High (80%)
Maximum scene change detection. The alarm message
appears when the field of view changes by 80% or more.
•
Medium (50%)
Medium scene change detection. The alarm message appears
when the field of view changes by 50% or more.
•
Low (30%)
Minimum scene change detection. The alarm message
appears when the field of view changes by 30% or more.
•
Disable (Default)
Disables scene change detection.
Click Apply to save the settings.
Setting Video Motion Detection (VMD)
An Administrator can enable and configure up to five zones to be monitored for motion in a
scene.
Note
The video analytics screen shows a static video snapshot instead of live video.
For this reason, you should open a second web client window for monitoring live
video.
Best Practices for Configuring Video Motion Detection
For best results configuring video motion detection, follow these steps:
1.
Identify areas in the image where motion detection alarms should be triggered.
In some applications, motion anywhere in the image needs to be reported. In other
applications, users will only want to monitor specific areas such as doors, stairwells, or
other areas of interest.
2.
Select one of the five available regions for each area of interest, and draw the box so that it
fully covers the area of interest.
Note
The camera only measures motion inside the drawn region-of-interest box. So a
person or vehicle moving along the boundary of the box may or may not trigger
an alarm, because their motion will only be evaluated partially. It is therefore
important to adjust the region-of-interest boxes to fully cover the areas of interest.
800-12606 - A - 03/2013
60 | H4D1FR1(X) User Guide
In cameras with a wide field of view, or where activity happens far away from the camera,
people and vehicles might appear rather small in the image and it might not be possible to
apply a single area of interest to the whole field of view and reliably detect motion. In such
cases, it is recommended that several smaller region-of-interest boxes be applied to areas
where motion alarms are of most interest to the user such as entrances, restricted access
areas, and so on.
3.
Use the medium sensitivity at 50% as the initial setting. This setting can be changed later
as needed (see Adjusting Video Motion Detection Sensitivity on page 61).
4.
Observe VMD performance in all expected lighting conditions after the initial configuration
is applied. Ensure that relevant scene motion does trigger alarms and ensure that the
camera is not reporting false alarms (such as VMD alarms triggered due to image noise).
Setting Video Motion Detection
To set video motion detection (VMD)
1.
2.
Next to Region, select one of the following:
•
Region 1 (Red)
•
Region 2 (Green)
•
Region 3 (Blue)
•
Region 4 (Magenta)
•
Region 5 (Cyan)
Next to VMD, select Enable.
A box corresponding to the region you selected in step 1 appears on the video display in
its default location.
3.
4.
If you want, you can move and resize the box.
a.
To move the box, click inside the box and drag it to a new location on the screen.
b.
To resize the box, hover your mouse over one of the sides of the box until the mouse
pointer becomes a double-headed arrow. then drag the side to its new position.
Next to Motion Threshold, select one of the following options:
•
High (80%)
Least sensitive to motion
•
Medium (50%)
Medium sensitivity to motion (recommended for initial setting)
•
Low (30%)
Most sensitive to motion
5.
Click Apply.
6.
Repeat steps 1 to 5 to configure additional regions if desired.
7.
To confirm that the VMD settings have been applied, go to another screen (such as
Camera Setup) and then return to the Video Analytics screen. Check that the VMD settings
have not changed.
Note
www.honeywellvideo.com
To disable a region that you have configured, next to Region, click the region
that you want to disable, and then, next to VMD, select Disable.
Setting Up the Camera | 61
Adjusting Video Motion Detection Sensitivity
Increasing Sensitivity
If relevant scene motion does not trigger VMD alarms, do the following:
•
Decrease the Motion Threshold level (from 80% to 50%, or from 50% to 30%). This will
increase the sensitivity of the motion detection, causing smaller objects to be detected
and decrease the contrast level (amount of noise) required to trigger an alarm. This should
be the primary adjustment mechanism.
•
Decrease the size of the region-of-interest box (and add more regions if needed). This will
cause smaller objects to be detected and trigger VMD alarms.
Note
After VMD sensitivity is increased, observe the performance in other lighting
conditions in case further adjustments are required to prevent false alarms.
Decreasing Sensitivity
If VMD alarms are triggered even when there is no motion and no significant changes in the
video, do the following:
•
Increase the Motion Threshold level (from 30% to 50%, or from 50% to 80%). This will
decrease the sensitivity of the motion detection by increasing the contrast level (amount of
noise) required to trigger an alarm. This should be the primary adjustment mechanism.
•
Increase the size of the region-of-interest box. This will prevent smaller objects (or smaller
areas of noise) from triggering VMD alarms.
Sample Video Motion Detection Configurations
The following examples are provided for illustration purposes only. Factors such as lighting
level, contrast, and image noise could affect VMD performance and require further adjustments
as described above.
Normal Field of View
In a normal field of view, with a person walking in front of the camera, the maximum
recommended region-of-interest box sizes would be as shown by the red boxes in Figure 4-15,
Figure 4-16, and Figure 4-17.
800-12606 - A - 03/2013
62 | H4D1FR1(X) User Guide
www.honeywellvideo.com
Figure 4-15
VMD Configuration (Low Motion Threshold - 30%)
Figure 4-16
VMD Configuration (Medium Motion Threshold - 50%)
Setting Up the Camera | 63
Figure 4-17
VMD Configuration (High Motion Threshold - 80%)
Wide Field of View
For cameras with a wide-angle field of view covering a larger scene, people who walk far away
from the camera might appear rather small in the image. If motion needs to be detected in the
entire field of view, the following region-of-interest box configuration is recommended:
•
Three smaller boxes, set to 30%, covering the upper portion of the image where people
appear small.
•
Two larger boxes, set to 50%, covering the lower portion of the image where objects
appear larger.
Figure 4-18
VMD Configuration - Combination Setup
800-12606 - A - 03/2013
64 | H4D1FR1(X) User Guide
Configuring Date and Time
The Date and Time view (Figure 4-19) lets you configure the time zone, the NTP server, and text
overlay settings.
Figure 4-19
Date and Time View
Setting the Time Zone
To set the time zone
1.
Under Time Zone Settings, select a time zone for your location from the drop-down list.
2.
If you want to activate automatic compensation for Daylight Saving Time, select the DST
check box.
Setting the Network Time Protocol (NTP) Server
Network Time Protocol (NTP) is a networking protocol for clock synchronization between
computer systems over packet-switched, variable-latency data networks. Honeywell ONVIF
cameras use NTP to synchronize camera time with an NTP server.
Note
www.honeywellvideo.com
Some anti-virus software, such as McAfee, will force-stop the NTP service.
Contact your local network administrator and check your anti-virus software
filtering policy before using an NTP service.
Setting Up the Camera | 65
There are two ways to configure NTP:
•
Use a DHCP server to set the NTP server address.
•
Specify an NTP server IP address for time synchronization.
DHCP
To use a DHCP server to synchronize time
•
Under NTP Settings, select the DHCP check box.
The camera will try to use your DHCP server to set the NTP server address. Contact your
local network administrator to confirm that your DHCP server has either a) installed and
enabled the NTP server in your workstation, or b) configured the DHCP server to send
NTP server address(es) to clients (most cases).
NTP Server
There are two types of NTP servers you can use to synchronize time: a public NTP server or a
local NTP server.
To use a public NTP server to synchronize time
1.
Search online for a public NTP server IP
address.
2.
Enter the IP address of the public NTP server
in the NTP Server field under NTP Settings.
Note
Before using a public NTP server, contact your local network administrator to
ensure that your network settings and firewall will not block the server.
To use a local NTP server to synchronize time
•
Enter the IP address of your local NTP server in the NTP Server field under NTP Settings.
•
Alternatively, install the Meinberg Network Time Protocol software included on the
installation DVD that was shipped with your camera. The software synchronizes your
computer clock with an external time source (typically another computer running an NTP
server) and can also set up your computer as an NTP server from which other computers
can synchronize.
800-12606 - A - 03/2013
66 | H4D1FR1(X) User Guide
Installing the NTP Software Included With Your Camera
To install the NTP software
1.
Insert the DVD that was shipped with your camera into your workstation’s DVD-ROM drive,
and then browse to the NTP folder.
2.
Click one of the following setup files:
[email protected]
NTP installation package with IPv6 support for XP/
2003 Server/Vista/Windows 7/Windows Server 2008
[email protected]
NTP installation package for Windows NT/2000
(IPv4 only)
ntp-time-server-monitor-1.04.exe
An NTP time server monitor program for Windows
operating systems that allows configuration of the local
NTP service and graphical monitoring of local and
remote NTP servers. (Optional)
For most applications, use [email protected]
3.
Follow the on-screen instructions to install the software.
On the Choose Components screen, click Next to install the default set of components.
www.honeywellvideo.com
Setting Up the Camera | 67
4.
On the Please specify your configuration settings screen you must do at least one of
the following to specify the NTP servers to synchronize with:
•
If the computer can access public Internet time servers, then under Want to use
predefined public NTP servers select the closest geographic region to where the
computer is installed. If the computer cannot access the public Internet (for example,
if it is not connected to the Internet or if a firewall blocks access to the NTP port), then
leave this setting as None.
•
If you want the computer to be able to synchronize with specific private servers (for
example, an NTP server on the corporate network or another computer running the
Meinberg NTP service), enter those host names or IP addresses under You can
specify up to 9 NTP servers (comma separated) you want to use. If you specify
more than one computer, separate them with commas.
•
If you want the computer to add the local clock as a last resort reference if both of the
above options have not worked because your network security settings have blocked
them, select the Add local clock as a last resort reference checkbox.
Click to select Add
local clock as a last
resort reference
You can set up all three options, if appropriate. The NTP service automatically polls all of
them and selects the best one to synchronize with.
If the computers that need to have synchronized clocks all have access to public Internet
time servers, then you can have all of them synchronize with the same servers.
If most of the computers do not have access to an NTP server, then you can select one
computer (for example, the Alarm Management Server) to be the time source, and have it
access a reliable NTP server, via the Internet, a corporate intranet, or even a hardware
radio clock.
Note
NTP uses UDP on port 123, so this port must be unblocked on the computer you
select to act as the time server for the other computers to synchronize with.
800-12606 - A - 03/2013
68 | H4D1FR1(X) User Guide
5.
When prompted to review the generated confide file, click No.
6.
On the NTP Service Options screen, accept the defaults, and then click Next.
7.
On the Enter the user ID and password used for running the service screen enter a
password for the NTPD account, and then click Next.
Note
www.honeywellvideo.com
Enter a strong security password, such as ASDFGhjkl;’, or you will get an error
(code 2245).
Setting Up the Camera | 69
After clicking Next, if a message appears indicating that the computer policy does not
allow you to create a new user account, click Back and select one of the other account
options (either Use existing account or Use SYSTEM account) from the top of the
Please specify your service settings screen.
8.
Click Finish.
Installing an NTP Time Server Monitor (Optional)
If you want, you can also install an NTP time server monitor program that lets you configure local
NTP service and monitor local and remote NTP servers.
To install the NTP Time Server Monitor
1.
Insert the DVD that was shipped with your camera into your workstation’s DVD-ROM drive,
and then browse to the NTP folder.
2.
Double-click ntp-time-server-monitor-1.04.exe.
3.
Follow the on-screen instructions to install the software.
For more information, visit http://www.meinbergglobal.com and click Support  Software
Download  NTP Download.
Overlay Settings
In the Overlay Settings area you can configure the appearance of on-screen text, including
color, size, and location.
800-12606 - A - 03/2013
70 | H4D1FR1(X) User Guide
Click to display the camera name.
Enable/disable date display.
Enable/disable time display.
Select a background color: White, Black, or
Transparent.
Choose a text color: Black or White.
Select the text size.
Select the overlay position.
System Setup
The System Setup view (Figure 4-20) lets you configure port allocation settings and the
snapshot file type and save path (Internet Explorer only). You can also reset the camera to
factory defaults and restart the camera from this screen.
Figure 4-20
www.honeywellvideo.com
System Setup View
Setting Up the Camera | 71
Setting the Port Allocation
In the Port Allocation area you can enter values
for the HTTP and RTSP ports.
If you are running the web client in Chrome or
Firefox, note that the following ports are blocked:
Ports Blocked by Chrome
Ports Blocked by Firefox
2049, // nfs
2049, // nfs
3659, // apple-sasl / PasswordServer
4045, // lockd
4045, // lockd
6000, // X11
6000, // X11
6665, // Alternate IRC [Apple addition]
6666, // Alternate IRC [Apple addition]
6667, // Standard IRC [Apple addition]
6668, // Alternate IRC [Apple addition]
6669, // Alternate IRC [Apple addition]
Setting the Snapshot File Type and Path (Internet Explorer Only)
In the Snapshot area you can set the file type
and save path for snapshots.
1.
Next to Path, click
save path.
2.
Next to Type, select either BMP or
JPEG (JPEG is the default file type).
3.
Click Apply to save the changes.
Note
to choose a
In Google Chrome and Mozilla Firefox, the snapshot file type and save path are
set when saving the snapshot (see Taking a Snapshot on page 47).
800-12606 - A - 03/2013
72 | H4D1FR1(X) User Guide
Resetting and Rebooting the Camera
In the Camera Reset area there are three options
for resetting the camera.
Reset to Factory Resets the camera to the factory
Defaults
defaults, including the network settings.
Reset
Resets the camera to the factory
defaults, except the network settings.
Restart
Restarts the camera while maintaining
the existing configurations.
Note
Each of these functions takes approximately two minutes to complete. During
that time, the camera’s connection to the web client is lost.
Viewing Device Information
The Device Information view (Figure 4-21) displays the network settings and firmware details of
the camera.
Figure 4-21
www.honeywellvideo.com
Device Information View
Setting Up the Camera | 73
In the Device Information area you can view read-only network settings, firmware settings, and
video formats for the camera without having to access the IP Utility (Figure 4-22).
Figure 4-22
IP and Firmware Settings
Firmware Version including product name
and version
Video Format - NTSC or PAL
Device Name as entered in the IP Utility
program
CVBS (local video out for aiming and
focusing - this is always enabled)
IP Address on the network
(DHCP/Static/APIPA)
Subnet Mask and Default Gateway address
that connects the camera to the network
MAC Address is a factory assigned address
unique for each device
Logging Out of the Web Client
To log out of the web client
•
Click LOGOUT in the upper right corner of the web client window.
Uninstalling Honeywell ONVIF ActiveX (Internet Explorer)
To uninstall the IP Utility in Windows 7
1.
Click the Start button, click Control Panel, click Programs, and then click Programs and
Features.
2.
Click Honeywell ONVIF ActiveX, and then click Uninstall.
If you are prompted to confirm that you want to uninstall the application, click Yes.
To uninstall the IP Utility in Windows XP
1.
Click Start, click Control Panel, and then double-click Add or Remove Programs.
2.
Click Honeywell ONVIF ActiveX, and then click Remove.
3.
You are prompted to confirm that you want to uninstall the application. Click Yes.
800-12606 - A - 03/2013
74 | H4D1FR1(X) User Guide
Uninstalling VLC Media Player (Chrome and Firefox)
To uninstall VLC media player in Windows 7
1.
Click the Start button, click Control Panel, click Programs, and then click Programs and
Features.
2.
Click VLC media player 2.0.5, and then click Uninstall.
If you are prompted to confirm that you want to uninstall the application, click Yes.
To uninstall VLC media player in Windows XP
1.
Click Start, click Control Panel, and then double-click Add or Remove Programs.
2.
Click VLC media player 2.0.5, and then click Remove.
3.
You are prompted to confirm that you want to uninstall the application. Click Yes.
www.honeywellvideo.com
A
Troubleshooting
A
If you encounter an issue with your camera, please read this section first. If you require
additional assistance, call 1-800-323-4576 (North America only) or send an email to
https://honeywellsystems.com/ss/techsupp/index.html. See the back cover for international
contact information.
Any equipment returned to Honeywell Video Systems for warranty or service repair must have
a Return Merchandise Authorization (RMA) number. The RMA number must be clearly marked
on all return packages and internal paperwork.
Lens not in optical focus
•
•
Check that the lens cap has been removed from the
camera.
Check the lens and bubble for dust, fingerprints, etc., and
clean if needed.
Note Use care when cleaning the lens and bubble that you
do not scratch them. Use a soft cloth or lens cleaning
paper with alcohol or lens cleaning liquid, and move in
a spiral motion from the center outward. Repeat until
the lens is completely clean.
Live View does not display
video
•
•
•
Check that your web browser settings have been
configured to allow ActiveX controls
Check that the network cable from the camera is
connected to both the camera and the network.
Check that the camera assembly board DIP switch
settings are configured correctly.
IP Utility installation fails
•
•
Disable Norton AntiVirus software, if present.
Check that Microsoft .NET Framework 3.5 is enabled on
your PC.
Cannot connect to a device
•
Your PC and the device you are connecting to may be on
different subnets. Contact your network administrator for
assistance.
800-12606 - A - 03/2013
76 | H4D1FR1(X) User Guide
www.honeywellvideo.com
B
Specifications
Note
B
These specifications are subject to change without notice.
Video Signal
Video Standard
NTSC/PAL
Scanning System
Progressive scan
Image Sensor
1/4-in. CMOS
Number of Pixels (H×V)
1280 × 720
Minimum Illumination
0.25 lux color / 0.22 lux BW @ 50 IRE, F1.4
0.11 lux color / 0.09 lux BW @ 30 IRE, F1.4
0 lux with IR LEDs on
Video Output
1.0 Vp-p, 75 ohms
S/N Ratio
50 dB or more (AGC off)
Auto Gain Control
On/Off, selectable (10–40 dB)
Auto Electronic Shutter
1/60–1/24,500 s (NTSC)
1/50–1/24,500 s (PAL)
Lens Type
3.3–12 mm VFAI, F1.4
Auto Lens Iris Control
DC iris level 1–25
IR LEDs
850 nm, 24 LEDs
IR Illumination Distance
Up to 50 ft (15 m), depending on scene reflectance
White Balance
AWC, AWC Push, Manual
Electrical
Input Voltage
24 V AC, PoE IEEE 802.3af, Class 1
Input Voltage Range
17–28 V AC
Surge Suppression
1.5 kW transient
Power Consumption
24 V AC: 3.5 W (max.)
PoE: PD Type 1 Class 1
800-12606 - A - 03/2013
78 | H4D1FR1(X) User Guide
Mechanical
Dimensions (W × H)
6.13 × 4.63 in. (154.94 × 117.1 mm)
Weight
3.0 lb (1.3 kg) camera only
Construction
Housing: Die-cast aluminum
Finish: Cool gray powder coating
Dome Cover: Polycarbonate
Connector
Aux video output: 2-pin Molex connector
Power input: Removable screw terminal block
Network: RJ45 connector
Environmental
Temperature
Operating: -13°F to 131°F (-25°C to 55°C)
Storage: -40°F to 158°F (-40°C to 70°C)
Relative Humidity
0% to 85%, non-condensing
Rating
IP66
Network
Video Compression
Dual stream H.264 and/or H.264/MJPEG
Resolution
Primary Stream: 1280×720, 800×450, 640×360, 320×180
Software Update
Field upgradeable
Frame Rate
Up to 30 fps (NTSC) / Up to 25 fps (PAL)
Video Streaming
Dual streaming: H.264 and/or H.264/MJPEG
Controllable frame rate and bandwidth
Security
Multiple user access levels with password protection
Video Access from Web
Browser
Full control of all camera settings available to administrator
Minimum Browsing
Requirements
Pentium 4 CPU 3.1 GHz or faster, 1 GB RAM (32 bit) or 2 GB RAM (64 bit),
Windows 7 (32/64 bit), Windows Server 2008 R2 (64 bit), Windows Vista SP1,
Windows Server 2003 R2 (32 bit), Windows XP Professional SP3, Internet
Explorer 8 or 9, Google Chrome v23.0.1271.97 or later, Mozilla Firefox v17.01
or later
Installation, Management,
and Maintenance
Honeywell IP Utility software identifies the IP address, checks device status,
and upgrades firmware over HTTP. Available at
www.honeywellsystems.com/support/download-center/index.html
Supported Protocols
HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, NTP, RTCP, FTP, ICMP, DHCP,
Bonjour, IGMP, SSH
Standards
ONVIF (Profile S)
Regulatory
Emissions
FCC Part 15B, EN 55022
Immunity
EN 50130-4
Safety
EN 60950-1
North America ETL listed to UL/CSA 60950-1
www.honeywellvideo.com
Specifications | 79
Mount Accessories
HD4CHIP-PK
Pendant mount bracket
HD4CHIP-WK
Wall mount bracket
800-12606 - A - 03/2013
80 | H4D1FR1(X) User Guide
www.honeywellvideo.com
Honeywell Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
 +1.800.796.2288
Honeywell Security Northern Europe
Ampèrestraat 41
1446 TR Purmerend, The Netherlands
www.honeywell.com/security/nl
 +31.299.410.200
Honeywell Security Europe/South Africa
Aston Fields Road, Whitehouse Industrial Estate
Runcorn, WA7 3DL, United Kingdom
www.honeywell.com/security/uk
 +44.01928.754028
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
 +49 74 31 / 8 01-18 70
Honeywell Systems Caribbean/Latin America
9315 NW 112th Ave.
Miami, FL 33178, USA
www.honeywellvideo.com
 +1.305.805.8188
Honeywell Security France
Immeuble Lavoisier
Parc de Haute Technologie
3-7 rue Georges Besse
92160 Antony, France
www.honeywell.com/security/fr
 +33.(0).1.40.96.20.50
Honeywell Systems Pacific
Level 3, 2 Richardson Place
North Ryde, NSW 2113, Australia
www.honeywellsecurity.com.au
 +61.2.9353.7000
Honeywell Systems Asia
35F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
 +86 21.5257.4568
Honeywell Security Middle East/N. Africa
Post Office Box 18530
LOB Building 08, Office 199
Jebel Ali, Dubai, United Arab Emirates
www.honeywell.com/security/me
 +971.04.881.5506
Honeywell Security Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
 +39.02.4888.051
Honeywell Security España
Avenida de Italia, n° 7, 2a planta
C.T.C. Coslada
28821 Coslada, Madrid, Spain
www.honeywell.com/security/es
 +34.902.667.800
www.honeywellvideo.com
+1.800.323.4576 (North America only)
https://honeywellsystems.com/ss/techsupp/index.html
Document 800-12606 – Rev A – 03/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change
without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement