user``s manual - Amazon Web Services

user``s manual - Amazon Web Services
www.epicfit.com
Model No. EPEX13912.4
Serial No.
Write the serial number in the
space above for reference.
Serial Number
Decal (under frame)
ACTIVATE YOUR
WARRANTY
To register your product and
activate your warranty today, go
to www.epicfit.com/registration.
CUSTOMER CARE
For service at any time, go to
www.epicfit.com.
Chat: Mon.––Fri. 6 a.m.––7 p.m. MT
Email: [email protected]
Call: 1-855-EPIC-FIT
(1-855-374-2348)
Mon.––Fri. 6 a.m.––7 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USER’’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s).
If a decal is missing or illegible, see the front cover
of this manual and request a free replacement decal.
Apply the decal in the location shown. Note: The
decal(s) may not be shown at actual size.
Misuse of this machine
may result in serious
injury.
Read user’s manual
prior to use and follow
all warnings and
instructions.
Do not allow children
on or around machine.
User weight must not
exceed 275 pounds.
This product should
always be used on a
level surface.
This product is not
intended for
therapeutic use.
Replace label if
damaged, illegible,
or removed.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. It is the responsibility of the owner to ensure
that all users of the exercise bike are adequately informed of all precautions.
8. Keep children under age 12 and pets away
from the exercise bike at all times.
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
10. The exercise bike should not be used by
persons weighing more than 275 lbs.
(125 kg).
3. Use the exercise bike only as described in
this manual.
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a commercial, rental, or institutional setting.
11. Be careful when mounting and dismounting
the exercise bike.
12. The heart rate monitor is not a medical
device. Various factors, including the user’’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
5. Keep the exercise bike indoors, away from
moisture and dust. Do not put the exercise
bike in a garage or covered patio, or near
water.
6. Place the exercise bike on a level surface
with at least 2 ft. (0.6 m) of clearance around
the exercise bike. To protect the floor or
carpet from damage, place a mat under the
exercise bike.
13. Always keep your back straight while using
the exercise bike; do not arch your back.
14. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
3
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary EPIC™™ A17U
exercise bike. Cycling is an effective exercise for
increasing cardiovascular fitness, building endurance,
and toning the body. The A17U exercise bike provides
an impressive selection of features designed to make
your workouts at home more effective and enjoyable.
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions after
Length: 3 ft. 5 in. (104 cm)
Width: 2 ft. 1 in. (64 cm)
Console
Handlebar
Heart Rate Monitor
Console Knob
Seat
Accessory Tray
Seat Knob
Pedal/Strap
Seat Post Knob
Wheel
Leveling Foot
5
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M4 x 12mm
Screw (75)––6
M4 x 15mm
Screw (80)––5
M8 x 13mm
Screw (72)––10
M10 x 105mm
Screw (76)––4
6
M10 x 16mm
Screw (74)––4
ASSEMBLY
•• To watch an assembly
video, go to
http://productvideo.co/
assembly/dsg/epic or
use your mobile phone
or smartphone to read
the QR code with an
application such as
ShopSavvy.
•• Left parts are marked ““L”” or ““Left”” and right parts
are marked ““R”” or ““Right.””
•• To identify small parts, see page 6.
•• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
•• Assembly requires two persons.
•• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
1. Go to www.epicfit.com/registration on your
computer and register your product.
1
•• activates your warranty
•• saves you time if you ever need to contact
Customer Care
•• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
2. Set a sturdy piece of packing material under the
rear of the Frame (1). Have a second person
hold the Frame to prevent it from tipping
while you complete this step.
2
Identify the Rear Stabilizer (3), which has a
Leveling Foot (29) on each end. Orient the Rear
Stabilizer as indicated by the sticker so that the
welded tubes are in the location shown.
3
Attach the Rear Stabilizer (3) to the Frame (1)
with two M10 x 105mm Screws (76).
29
Remove the packing material.
1
29
7
Welded
Tubes
76
3. Set a sturdy piece of packing material under the
front of the Frame (1). Have a second person
hold the Frame to prevent it from tipping
while you complete this step.
3
Wheel
76
2
Orient the Front Stabilizer (2) as shown.
Attach the Front Stabilizer (2) to the Frame (1)
with two M10 x 105mm Screws (76).
Remove the packing material.
1
4. Orient the Seat Post (6) as shown.
4
Next, loosen the Seat Post Knob (49) a few
turns, pull the Seat Post Knob outward, and
insert the Seat Post (6) into the Frame (1).
6
Slide the Seat Post (6) upward or downward to
the desired position, and then release the Seat
Post Knob (49) into one of the adjustment holes
in the Seat Post. Move the Seat Post upward
or downward slightly to make sure that the
Seat Post Knob is engaged in one of the
adjustment holes. Then, tighten the Seat Post
Knob.
Adjustment
Holes
1
49
5. Note: It may be necessary to remove the
Adjustment Knob (not shown) from the Seat
Carriage Block (30).
5
Attach the Seat (23) to the Seat Carriage (24)
with four M8 x 13mm Screws (72). Make sure
that the Seat Carriage Block (30) is inside the
Seat Carriage.
23
30
24
72
8
6. Set the Seat Carriage (24) on the Seat Post (6)
and hold it in place.
6
Insert the Adjustment Knob (27) upward into the
Seat Post (6), and tighten the Adjustment Knob
into the Seat Carriage Block (30) inside the Seat
Carriage (24).
24
30
6
27
7. Orient the Front Shield Cover (7) and the Upright
(4) as shown. Slide the Front Shield Cover onto
the Upright.
7
Wire Tie
While a second person holds the Upright (4)
near the Frame (1), tie the lower end of the wire
tie in the Upright to the Main Wire (58). Then,
pull the upper end of the wire tie until the Main
Wire is routed through the Upright.
Avoid pinching the
Main Wire (58)
Tip: To prevent the Main Wire (58) from
falling into the Upright (4), secure the Main
Wire with the wire tie.
4
7
Tip: Avoid pinching the Main Wire (58). Slide
the Upright (4) onto the Frame (1). Attach the
Upright with four M10 x 16mm Screws (74).
74
74
Then, slide the Front Shield Cover (7) downward
and press it onto the Left and Right Shields
(10, 11).
Wire Tie
58
1
10, 11
9
8. Attach the Accessory Tray (46) to the Upright (4)
with four M4 x 15mm Screws (80).
8
46
4
80
9. Orient the Handlebar (5) as shown.
80
9
Avoid pinching
the wires
Tip: Avoid pinching the Pulse Wire (17) and
the Main Wire (58). Attach the Handlebar (5)
to the Pivot Bracket (35) with six M8 x 13mm
Screws (72).
72
5
17
72
35
58
10. Untie and discard the wire tie (not shown) on the
Main Wire (58).
10
Wires
Have a second person hold the Console (13)
near the Pivot Bracket (35).
17
Insert all the wires on the Console (13)
downward through the hole in the center of the
Pivot Bracket (35).
58
4
Connect the Main Wire (58) and the Pulse Wire
(17) to the matching wires on the Console (13).
A
Insert the remaining wire (A) downward into the
Upright (4) and pull it out of the hole in the left
side of the Upright.
10
35
13
11. Tip: Avoid pinching the wires. It may be
necessary to turn the Adjustment Knob (27)
and adjust the angle of the Pivot Bracket (35).
11
13
35
Attach the Console (13) to the Pivot Bracket (35)
with four M4 x 12mm Screws (75).
75
27
Avoid pinching
the wires
12. Tip: It may be necessary to turn the
Adjustment Knob (27) and adjust the angle of
the Pivot Bracket (35).
12
75
Attach the Lower Pivot Cover (12) to the Pivot
Bracket (35) with two M4 x 12mm Screws (75).
Make sure that the indicated wire (A) is not
covered by the Lover Pivot Cover (12) (see
the drawing in step 13).
35
A
27
12
13. Tip: Avoid pinching the wires.
13
Orient the Upper Pivot Cover (9) as shown.
Press the Upper Pivot Cover onto the Lower
Pivot Cover (12).
80
Avoid pinching
the wires
9
13
Attach the Upper Pivot Cover (9) to the Console
(13) with an M4 x 15mm Screw (80).
12
A
11
14. Identify the Left and Right Upright Covers
(14, 15) and orient them as shown.
14
15
Have a second person hold the Right Upright
Cover (15) near the right side of the Upright (4)
Connect the wire on the Receiver (59) to the
wire (A) in the Upright.
Insert the excess wire into the Upright (4).
59
4
14
Tip: Avoid pinching the wires. Press the Left
and Right Upright Covers (14, 15) together
around the Upright (4).
A
Avoid pinching
the wires
15. Identify the Left Pedal (21).
15
Using the included flat wrench, firmly tighten
the Left Pedal (21) counterclockwise into the
Left Crank Arm (19).
Strap
Firmly tighten the Right Pedal (not shown)
clockwise into the Right Crank Arm (not shown).
21
19
Adjust the strap on the Left Pedal (21) to the
desired position, and press the ends of the strap
onto the tabs on the Left Pedal. Adjust the
strap on the Right Pedal (not shown) in the
same way.
16. Plug the Power Adapter (67) into the receptacle
on the front of the exercise bike.
Tab
16
Note: To plug the Power Adapter (67) into an
outlet, see HOW TO PLUG IN THE POWER
ADAPTER on page 14.
67
17. After the exercise bike is assembled, inspect it to make sure that it is assembled correctly and that it
functions properly. Make sure that all parts are properly tightened before you use the exercise bike.
Note: Extra parts may be included. Place a mat under the exercise bike to protect the floor or carpet.
12
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
The heart rate
monitor consists of
a chest strap and a
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sensor under the buckle
on the chest strap.
The tab should be
flush with the front of
the sensor.
Tabs
•• Do not expose the heart rate monitor to direct sunlight for extended periods of time; do not expose it to
temperatures above 122° F (50° C) or below 14° F
(-10° C).
Chest
Strap
•• Do not excessively bend or stretch the sensor when
using or storing the heart rate monitor.
Sensor
•• To clean the sensor, use a damp cloth and a small
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
TROUBLESHOOTING
Tab
If the heart rate monitor does not function properly, try
the steps below.
Sensor Buckle
The heart rate monitor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the
location shown.
Make sure that
the logo is rightside-up. Then, attach the other end of the chest strap
to the sensor. Adjust the length of the chest strap, if
necessary.
•• Make sure that you are wearing the heart rate monitor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
•• If heart rate readings are not displayed until you
begin perspiring, rewet the electrode areas.
•• For the console to display heart rate readings, you
must be within arm’’s length of the console.
•• If there is a battery cover on the back of the sensor,
replace the battery with a new battery of the same
type.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
•• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
CARE AND MAINTENANCE
•• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
•• Thoroughly dry the sensor with a soft towel after
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
•• Store the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
13
HOW TO USE THE EXERCISE BIKE
HOW TO PLUG IN THE POWER ADAPTER
HOW TO ADJUST THE HEIGHT OF THE SEAT
IMPORTANT: If the exercise bike has been exposed
to cold temperatures, allow it to warm to room
temperature before you plug in the power adapter.
If you do not do this, you may damage the console
displays or other electronic components.
For effective exercise, the seat should be at the proper
height. As you pedal, there should be a slight bend in
your knees when the pedals are in the lowest position.
Plug the power
adapter into the
receptacle on
the frame of the
exercise bike.
Then, plug the
power adapter
into an appropriate outlet that is
properly installed
in accordance with
all local codes and
ordinances.
To adjust the
height of the seat,
first loosen the
indicated adjustment knob a few
turns. Next, pull
the knob outward,
slide the seat
post upward or
downward to the
desired position,
and then release
Knob
the knob into one
of the adjustment
holes in the seat
post. Move the
seat post upward
or downward
slightly to make sure that the knob is engaged in
one of the adjustment holes in the seat post. Then,
tighten the knob.
Power Adapter
HOW TO LEVEL THE EXERCISE BIKE
If the exercise
bike rocks slightly
on your floor
during use, turn
one or both of
the leveling feet
beneath the rear
stabilizer until the
rocking motion is
eliminated.
HOW TO ADJUST THE HORIZONTAL POSITION OF
THE SEAT
To adjust the
horizontal position of the seat,
first loosen the
indicated adjustment knob a few
turns. Then, move
the seat forward
or backward to the
desired position,
and firmly tighten
the knob.
Leveling
Feet
14
Knob
HOW TO ADJUST THE ANGLE OF THE
CONSOLE AND THE HANDLEBAR
HOW TO ADJUST THE PEDAL STRAPS
To adjust the
pedal straps, first
pull the ends of
the straps off the
tabs on the pedals. Then, adjust
the straps to the
desired position,
and press the
ends of the straps
onto the tabs.
To adjust the
angle of the
console and the
handlebar, simply
turn the indicated
adjustment knob
clockwise or counterclockwise.
Knob
15
Strap
Tab
CONSOLE DIAGRAM
MAKE YOUR FITNESS GOALS A REALITY WITH
IFIT.COM
Upload your workout results to the iFit cloud
and track your accomplishments.
With your new iFit-compatible fitness equipment, you
can use an array of features on iFit.com to make your
fitness goals a reality:
Set calorie, time, or distance goals for your
workouts.
Exercise anywhere in the world with
customizable Google Maps.
Choose and download sets of weight-loss
workouts
Download training workouts designed to
help you reach your personal goals.
Go to iFit.com to learn more.
Measure your progress by competing
against other users in the iFit community.
16
FEATURES OF THE CONSOLE
HOW TO SET UP THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
Before using the exercise bike for the first time, set up
the console.
1. Create an iFit account.
The console features revolutionary iFit technology that
enables the console to communicate with your wireless
network. With iFit technology, you can download personalized workouts, create your own workouts, track
your workout results, and access many other features.
See www.iFit.com for complete information.
To create an iFit account, or for more
information about the account, go to
www.iFit.com.
Follow the prompts on the website to sign up for
your iFit membership. If you have an activation
code, select the code activation option.
In addition, the console features a selection of onboard
workouts. Each onboard workout automatically
changes the resistance of the pedals and prompts you
to vary your pedaling speed as it guides you through
an effective workout. You can also set a time, distance,
or calorie goal.
2. Connect to your wireless network.
Note: In order to download iFit workouts and
use other features of the console, you must be
connected to a wireless network. See HOW TO
CHANGE CONSOLE SETTINGS on page 24 to
connect the console to your wireless network.
The console also offers user-defined workouts that
allow you to create your own workouts and store them
in memory for future use.
3. Check for firmware updates.
When you use the manual mode of the console, you
can change the resistance of the pedals with the touch
of a button.
See HOW TO CHANGE CONSOLE SETTINGS on
page 24 and check for firmware updates.
While you exercise, the console will display continuous
exercise feedback. You can also measure your heart
rate using the handgrip heart rate monitor or the chest
heart rate monitor.
The console is now ready for you to begin working out.
The following pages explain the various workouts and
other features that the console offers.
To use the manual mode, see page 18. To use
an onboard workout, see page 20. To use a
set-a-goal workout, see page 21. To create a
user-defined workout, see page 21. To use a
user-defined workout, see page 22. To use an iFit
workout, see page 23. To change console settings, see page 24. To use the sound system, see
page 26.
You can also listen to your favorite workout music or
audio books with the console sound system while you
exercise.
To set up the console, see this page.
Note: If there is a sheet of plastic on the display,
remove the plastic.
Note: The console can display distance in either
miles or kilometers. To find which unit of measurement is selected, see HOW TO CHANGE CONSOLE
SETTINGS on page 24.
17
HOW TO USE THE MANUAL MODE
Calories per Hour (Calories/Hr)——This display
mode will show the approximate number of calories
you are burning per hour.
1. Begin pedaling or press any button on the
console to turn on the console.
Distance——This display mode will show the distance that you have pedaled in miles or kilometers.
When you turn on the console, the display will turn
on. The console will then be ready for use.
Laps——This display mode will show a track that
represents 1/4 mile (400 m). As you exercise, indicators will appear in succession around the track
to show your progress. The Laps display mode will
also show the number of laps you complete.
2. Select the manual mode.
The manual mode will be selected automatically
each time you turn on the console.
Note: If the console is connected to iFit through
your wireless network, the display will cycle
between the manual mode and the iFit welcome
message. Press the Home button repeatedly to
select the manual mode.
Pulse——This display mode will show your heart rate
when you use the handgrip heart rate monitor or
the chest heart rate monitor (see step 5).
Resistance——This display mode will show the
resistance level of the pedals for a few seconds
each time the resistance level changes.
You can also press any of the workouts buttons
repeatedly to select the manual mode.
RPM——This display mode will show your pedaling
speed in revolutions per minute (rpm).
3. Change the resistance of the pedals as desired.
As you pedal, you can change the resistance of the
pedals. To change the resistance, press the Quick
Resistance increase and decrease buttons or press
one of the numbered Quick Resistance buttons.
Speed——This display mode will show your pedaling
speed in miles or kilometers per hour.
Time——This display mode will show the elapsed
time.
Note: After you press a button, it will take a
moment for the pedals to reach the selected resistance level. If the pedals do not move for several
minutes and the buttons are not pressed, the
resistance of the pedals will increase.
The matrix offers several display modes. Press the
increase and decrease buttons near the Enter button until the desired display mode is shown.
Speed——This display mode will show a history of
the speed settings of your workout. A new segment
will appear at the end of each minute.
4. Follow your progress.
The display can show the following workout
information:
Calorie——This display mode will show the approximate amount of calories you have burned. The
height of each segment represents the amount of
calories burned during that segment. A new segment will appear at the end of each minute.
Calories——This display mode will show the approximate number of calories you have burned.
18
To pause the manual mode or a workout, stop pedaling. The time will pause in the display. To resume
the manual mode or the workout, simply resume
pedaling.
When your pulse is detected, your heart rate
will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15
seconds.
Press the Home button to exit the manual mode
or a workout. If necessary, press the Home button
again.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
When the console is connected to a
wireless network, the wireless symbol
in the display will show the strength
of your wireless signal. Four arcs
indicate full signal strength. If the wireless symbol
is flashing, the console is not connected to a wireless network.
6. Turn on the fan if desired.
The fan has high and low speed
settings. Press the fan increase and
decrease buttons repeatedly to select
a fan speed or to turn off the fan.
If desired, adjust the volume level by
pressing the volume increase and
decrease buttons on the console.
Note: If the pedals do not move for a
while, the fan will turn off automatically.
5. Measure your heart rate if desired.
7. When you are finished exercising, the console
will turn off automatically.
To use the chest heart rate monitor, see page
13. To use the handgrip heart rate monitor, follow the instructions below. IMPORTANT: If you
use both heart rate monitors at the same time,
the console will not display your heart rate
accurately.
If there are sheets
of plastic on the
metal contacts
on the handgrip
heart rate monitor,
remove the plastic. To measure
your heart rate,
hold the handgrip
heart rate monitor
with your palms
resting against the
contacts. Avoid
moving your
hands or gripping
the contacts tightly.
If the pedals do not move for several seconds, a
tone will sound, the console will pause, and the
time will flash in the display. To resume your workout, simply resume pedaling.
If the pedals do not move for several minutes and
the buttons are not pressed, the resistance of the
pedals will increase, the console will turn off, and
the display will be reset.
Contacts
19
HOW TO USE AN ONBOARD WORKOUT
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Quick Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Select an onboard workout.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
To select an onboard workout, press the Calorie
button or the Performance button repeatedly until
the name of the desired workout appears in the
display.
When you select an onboard workout, the display
will show the name, duration, and distance of the
workout. The display will also show the approximate number of calories you will burn during the
workout and a profile of the resistance settings of
the workout.
The workout will continue in this way until the last
segment ends. To pause the workout, stop pedaling. The time will pause in the display. To resume
the workout, simply resume pedaling.
3. Begin pedaling to start the workout.
4. Follow your progress.
Each workout is divided into segments. One
resistance level and one target rpm (speed) are
programmed for each segment. Note: The same
resistance level and/or target rpm may be programmed for consecutive segments.
See step 4 on page 18.
The matrix will also show a profile of the resistance
settings of the workout or a map.
5. Measure your heart rate if desired.
During the workout, the profile will show your progress. The flashing segment of the profile represents
the current segment of the workout. The height of
the profile indicates the approximate resistance
level for the current segment.
See step 5 on page 19.
6. Turn on the fan if desired.
See step 6 on page 19.
At the end of each segment of the workout, the
resistance of the pedals will change.
7. When you are finished exercising, the console
will turn off automatically.
As you exercise, keep your pedaling speed
near the target rpm for the current segment.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
See step 7 on page 19.
20
HOW TO USE A SET-A-GOAL WORKOUT
HOW TO CREATE A USER-DEFINED WORKOUT
1. Begin pedaling or press any button on the
console to turn on the console.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Set a calories, distance, or time goal.
2. Select a user-defined workout.
Press the Set A Goal button repeatedly until the
name of the desired goal appears in the display.
To select a user-defined workout, press the User
Defined button repeatedly until the name of the
desired workout appears in the display. A profile will
also appear in the display.
Then, press the increase and decrease buttons
near the Enter button to set the desired goal.
3. Begin pedaling and program the desired
settings.
3. Begin pedaling to start the workout.
As you exercise, a target rpm (speed) may
appear in the display to help you reach your goal.
Keep your pedaling speed near the target rpm.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
Each workout is divided into segments. You can
program one resistance level and one target rpm
(speed) for each segment.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
To program a target rpm (speed), simply pedal at
the desired speed.
To program a resistance level for the first segment,
simply adjust the resistance of the pedals by pressing the Quick Resistance buttons.
At the end of the first segment, the workout will
store the current resistance level and pedaling
speed in memory.
Program a resistance level and a target rpm for the
second segment as described above.
The workout will continue in this way until the calories, distance, or time goal is reached. To pause
the workout, stop pedaling. The time will pause in
the display. To resume the workout, simply resume
pedaling.
Continue exercising for up to one hundred minutes.
Press the Home button when you are finished with
your workout. Then, press the Enter button. The
workout you created will then be stored in memory.
4. Follow your progress.
4. When you are finished exercising, the console
will turn off automatically.
See step 4 on page 18.
See step 7 on page 19.
5. Measure your heart rate if desired.
See step 5 on page 19.
6. Turn on the fan if desired.
See step 6 on page 19.
7. When you are finished exercising, the console
will turn off automatically.
See step 7 on page 19.
21
HOW TO USE A USER-DEFINED WORKOUT
The workout will continue in this way until the last
segment ends. To pause the workout, stop pedaling. The time will pause in the display. To resume
the workout, simply resume pedaling.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
4. Change the workout if desired.
If desired, you can change the workout while you
are using it.
2. Select a user-defined workout.
To select a user-defined workout, press the User
Defined button repeatedly until the name of the
desired workout appears in the display. The display
will also show a profile of the resistance settings of
the workout.
To change the resistance level for the current
segment, simply press the Quick Resistance buttons. At the end of the current segment, the new
resistance level will be stored in memory.
To change the target rpm for the current segment, simply change your pedaling speed. At the
end of the current segment, your pedaling speed
will be stored in memory.
Note: To create a user-defined workout, see HOW
TO CREATE A USER-DEFINED WORKOUT on
page 21.
3. Start the workout.
If desired, you can shorten the workout. To
shorten the workout, press any workout button on
the console, and then press the Enter button to trim
the workout.
Each workout is divided into segments. One
resistance level and one target rpm (speed) are
programmed for each segment. Note: The same
resistance level and/or target rpm may be programmed for consecutive segments.
If desired, you can extend the workout when
you reach the end of the workout. To extend the
workout, follow the instructions in the matrix.
During the workout, the profile will show your progress. The flashing segment of the profile represents
the current segment of the workout. The height of
the flashing segment indicates the resistance level
for the current segment.
Continue exercising for up to one hundred minutes.
Press the Home button when you are finished with
your workout. Then, press the Enter button. The
workout will then be stored in memory.
At the end of each segment of the workout, the
resistance of the pedals will change.
5. Follow your progress.
See step 4 on page 18.
As you exercise, keep your pedaling speed
near the target rpm for the current segment.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
6. Measure your heart rate if desired.
See step 5 on page 19.
7. Turn on the fan if desired.
If the resistance level for the current segment is too
high or too low, you can manually override the setting by pressing the Quick Resistance buttons.
See step 6 on page 19.
8. When you are finished exercising, the console
will turn off automatically.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
See step 7 on page 19.
22
HOW TO USE AN IFIT WORKOUT
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
Note: To use an iFit workout, you must have access to
a wireless network (see page 24). An iFit account is
also required (see step 1 on page 17).
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
5. Begin pedaling to start the workout.
See step 3 on page 20.
2. Select the iFit mode.
During some workouts, the voice of a personal
trainer will guide you through your workout.
Press the Home button repeatedly to select the iFit
mode. The iFit welcome message will appear in the
display.
To stop the workout at any time, stop pedaling. The
time will flash in the display. To resume the workout, simply resume pedaling.
3. Select a user.
If more than one user is registered with your
iFit.com membership, you can switch users in the
iFit main screen. Press the increase and decrease
buttons near the Enter button to select a user.
6. Follow your progress.
See step 4 on page 18.
During a competition workout, the display can show
your progress in the race. As you race, the top line
in the matrix will show how much of the race you
have completed. The other lines will show your top
four competitors. The end of the matrix represents
the end of the race.
4. Select an iFit workout.
To download an iFit workout in your schedule,
press the Map, Train, or Lose Wt. button to download the next workout of that type in your schedule.
To compete in a race that you have previously
scheduled, press the Compete button.
7. Measure your heart rate if desired.
See step 5 on page 19.
To re-run a recent iFit workout from your schedule, press the Track button, press the increase
and decrease buttons to select the desired workout, and then press the Enter button to start the
workout.
8. Turn on the fan if desired.
See step 6 on page 19.
9. When you are finished exercising, the console
will turn off automatically.
To use a set-a-goal workout, press the Set A Goal
button (see page 21).
See step 7 on page 19.
Before some workouts will download, you must add
them to your schedule on iFit.com.
For more information about iFit workouts, go to
www.iFit.com.
For more information about the iFit workouts,
please see www.iFit.com.
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter inside
the console must be at least 8 in. (20 cm) from all
persons and must not be near or connected to any
other antenna or transmitter.
When you select an iFit workout, the display will
show the name, duration, and distance of the workout. The display will also show the approximate
number of calories you will burn during the workout and a profile of the resistance settings of the
workout.
23
HOW TO CHANGE CONSOLE SETTINGS
Contrast——The contrast level of the display will
appear in the matrix. Press the Quick Resistance
increase and decrease buttons to adjust the contrast level.
The console features a settings mode that allows you
to view usage information, to personalize console settings, and to set up and manage a wireless network
connection.
Firmware Update——For the best results,
regularly check for firmware updates.
1. Select the settings mode.
Note: The matrix will display NOT CONNECTED if
the console is not connected to a wireless network.
To select the settings mode, press and hold down
the Calorie button until the settings mode appears
in the display.
Press the Enter button to check for firmware
updates using your wireless network. If an update
is available, the update will begin automatically.
The time display will show the total number of
hours that the exercise bike has been used.
IMPORTANT: To avoid damaging the exercise
bike, do not unplug the power adapter while
the firmware is being updated. The update may
take several minutes.
The distance display will show the total number of
miles (or kilometers) that have been pedaled on the
exercise bike.
2. Navigate the settings mode menu.
Note: Occasionally, a firmware update may cause
your console to function slightly differently. These
updates are always designed to improve your exercise experience.
The matrix will display a menu of the settings mode
options.
Press the increase and decrease buttons near the
Enter button to highlight the desired option.
Default Settings——To restore the console to its
factory default settings, press the Enter button.
Note: The console will erase any information that
you have saved in its memory.
The lower part of the matrix will display instructions
for the highlighted option. Make sure to follow the
instructions displayed in the lower part of the
matrix.
IP Address——An IP address will appear in the
matrix. Note: This IP address is for reference.
3. Change settings as desired.
The WiFi––Normal option will allow you to set up
a wireless network connection using the console.
See step 4 for instructions.
Demo——The console features a display demo
mode, designed to be used if the exercise bike
is displayed in a store. While the demo mode is
turned on, the display will not enter sleep mode
when the exercise bike is not in use. If the demo
mode is turned on, the word ON will appear in the
matrix. To turn on or turn off the demo mode, press
the Enter button.
The WiFi––WPS option will allow you to set up
a wireless network connection using your WPS
router. See step 5 for instructions.
The WiFi––Advanced option will allow you to set up
a wireless network connection using your computer, smart phone, tablet, or other Wi-Fi device.
See step 6 for instructions.
Units——The selected unit of measurement will
appear in the matrix. To change the unit of measurement, press the Enter button. To view distance
in miles, select ENGLISH. To view distance in
kilometers, select METRIC.
24
iFit User Setup——To set up a different iFit account,
but maintain the existing wireless connection,
follow the instructions in the matrix. Note: This
option will be used rarely.
Press the up, down, left, and right buttons to highlight the desired letter or number. Then, press the
Enter button to select the letter, number, or symbol.
When you have finished entering the password,
press the Done button.
Clear WiFi——To erase the console’’s wireless
network settings and have it forget the currently
selected wireless network, follow the instructions in
the matrix.
Next, a numerical code and a web address will
appear in the matrix.
Open a web browser on your computer, smart
phone, tablet, or other internet-compatible device
and go to the web address.
4. Use WiFi––Normal to set up a wireless
connection.
This option will allow you to set up a wireless network connection using the console.
Log in to your iFit account on the web page. Then,
enter the numerical code into the indicated field on
the web page. Follow any other instructions on the
web page.
Note: You will need to know your network name
(SSID). If your network has a password, you will
also need to know the password.
Then, unplug the power adapter, wait for several
seconds, and then plug in the power adapter again.
Note: It may take a few minutes for the console to
be ready for use.
To set up a wireless network connection using the
console, first press the Enter button.
IMPORTANT: Set
the included WiFi
setup card on
the console. The
buttons on the
WiFi setup card
are referenced
in the following
instructions.
When the console is connected to a wireless
network, the wireless symbol in the display will
stop flashing and become solid. The wireless symbol will show the strength of your wireless signal;
four arcs indicate full signal strength.
Card
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
5. Use WiFi––WPS to set up a wireless connection.
A list of networks will appear in the matrix. Press
the up and down buttons to highlight the desired
network. Then, press the Enter button. Note: Do
not select IFIT_SETUP.
This option will allow you to set up a wireless network connection using your WPS router.
To set up a wireless network connection using your
WPS router, first press the Enter button and follow
the instructions in the matrix.
Note: The time display will show the number of
the currently-selected access point. The distance
display will show the total number of access points
detected.
A numerical code and a web address will appear in
the matrix. Open a web browser on your computer,
smart phone, tablet, or other internet-compatible
device and go to the web address.
If the network has a password, enter the password.
A keyboard will appear in the matrix. As necessary,
press the buttons on the WiFi setup card to select
the caps option, the number option, or the symbol
option.
Log in to your iFit account on the web page. Then,
enter the numerical code into the indicated field on
the web page. Follow any other instructions on the
web page.
25
Then, unplug the power adapter, wait for several
seconds, and then plug in the power adapter again.
Note: It may take a few minutes for the console to
be ready for use.
Your browser will load a web page. If the web page
does not appear, double-check the IP address and
the previous instructions of this step. Follow the
instructions on the web page to connect the exercise bike to your wireless network.
When the console is connected to a wireless
network, the wireless symbol in the display will
stop flashing and become solid. The wireless symbol will show the strength of your wireless signal;
four arcs indicate full signal strength.
Note: A warning may appear stating that the server
cannot be identified. If this happens, make sure
that you have entered the IP address correctly.
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
7. Exit the information mode.
6. Use WiFi––Advanced to set up a wireless
connection.
To exit the information mode, press the Calorie
button.
This option will allow you to set up a wireless
network connection using your computer, smart
phone, tablet, or other Wi-Fi device.
HOW TO USE THE SOUND SYSTEM
On your computer, smart phone, tablet, or other
Wi-Fi device, open the list of available networks to
which your device can connect. One of the options
will be IFIT_SETUP; select this network. If this network does not appear, make sure that your Wi-Fi
device is within range of the console, and then
close and re-open your list of networks. Also, see
CLEAR WIFI on page 25 and clear any previous
wireless network settings on the console.
To play music or audio books through the console
sound system while you exercise, plug a 3.5 mm male
to 3.5 mm male audio cable (not included) into the jack
on the console and into a jack on your MP3 player,
CD player, or other personal audio player; make sure
that the audio cable is fully plugged in. Note: To
purchase an audio cable, see your local electronics
store.
Next, press the play button on your
personal audio player. Adjust the volume
level using the volume increase and
decrease buttons on the console or the
volume control on your personal audio
player.
Note: The network IFIT_SETUP will not appear
if the console has already been configured to
connect to a wireless network. Also, AndroidTM
devices may not be able to detect IFIT_SETUP.
The console will display an IP address, such as
192.168.0.1:8080. Open a web browser on your
computer, smart phone, tablet, or other Wi-Fi
device. Next, type in the IP address on the console into the URL bar in your browser. Example:
http://192.168.0.1:8080.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat
surface instead of on the console.
26
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15C and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, try to correct the interference by one or more of the following measures:
••
••
••
••
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’’s authority to operate this equipment.
IMPORTANT: To satisfy exposure compliance requirements, the antenna and transmitter in the console
must be at least 8 in. (20 cm) from all persons and must not be near or connected to any other antenna or
transmitter.
Note: The console contains FCC ID: X2NBL-LW02-2 or GGOBL-LW05-2M.
27
MAINTENANCE AND TROUBLESHOOTING
IMPORTANT: Servicing other than the procedures
described below should be performed only by an
authorized service representative.
Locate the Reed Switch (57). Loosen, but do not
remove, the M4 x 16mm Screw (78).
Inspect and tighten all parts of the exercise bike regularly. Replace any worn parts immediately.
38
To clean the exercise bike, rst unplug the power
adapter. Wipe exterior parts of the exercise bike
with a damp cloth and a few drops of mild dish soap.
Then, wipe the exercise bike with a cloth dampened
with clean water, and dry the exercise bike with a soft
towel. IMPORTANT: Do not spray liquid directly
onto the console or onto other parts of the exercise bike. To avoid damage to the console, keep
the console out of direct sunlight.
55
57
78
CONSOLE TROUBLESHOOTING
If lines appear in the console display, see HOW TO
CHANGE CONSOLE SETTINGS on page 24 and
adjust the contrast level of the display.
Next, rotate the Pulley (38) until a Magnet (55) is
aligned with the Reed Switch (57). Slide the Reed
Switch slightly toward or away from the Magnet. Then,
retighten the M4 x 16mm Screw (78).
If the console does not display your heart rate when
you use the handgrip heart rate monitor, see step 5 on
page 19.
Plug in the power adapter. Rotate the Pulley (38) for
a moment. Repeat these actions until the console displays correct feedback.
If the console does not display your heart rate
when you use the chest heart rate monitor, see
TROUBLESHOOTING on page 13.
When the reed switch is correctly adjusted, reattach
the top shield cover.
HOW TO ADJUST THE REED SWITCH
STORAGE
If the console does not display correct feedback, the
reed switch should be adjusted.
If the exercise bike will not be used for an extended
period of time, unplug the power adapter and lay it
over the exercise bike where it will not be pinched or
crushed, and cover the exercise bike to keep it free
of dust. Store the exercise bike indoors. Do not store
objects on the exercise bike.
Unplug the
power adapter.
Using a flat screwdriver, release the
tabs along the Top
Shield Cover (8)
and remove the
Top Shield Cover.
8
28
EXERCISE GUIDELINES
Burning Fat——To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise——If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up——Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise——Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down——Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your ““training zone.”” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
29
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
2
1
2
1
2
2
1
1
1
2
1
1
1
2
2
1
4
Model No. EPEX13912.4 R0813A
Description
Key No. Qty.
Frame
Front Stabilizer
Rear Stabilizer
Upright
Handlebar
Seat Post
Front Shield Cover
Top Shield Cover
Upper Pivot Cover
Left Shield
Right Shield
Lower Pivot Cover
Console
Left Upright Cover
Right Upright Cover
Pulse Sensor
Pulse Wire
Crank Cover Cap
Left Crank Arm
Right Crank Arm
Left Pedal/Strap
Right Pedal/Strap
Seat
Seat Carriage
M8 x 15mm Screw
Knob Cap
Adjustment Knob
Seat Post Sleeve
Leveling Foot
Seat Carriage Block
Crank Cover
Rear Stabilizer Cap
Left Stabilizer Cap
Right Stabilizer Cap
Pivot Bracket
M6 x 12mm Screw
Sleeve Cover
Pulley
Crank
Crank Bearing
Snap Ring
Eddy Mechanism
Crank Cover Bracket
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
*
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
2
2
5
1
2
1
2
1
4
4
10
2
4
6
4
8
1
4
9
1
1
1
3
8
––
Description
Carriage Cap
Idler
Accessory Tray
Resistance Motor
Medium Shaft
Seat Post Knob
Upper Block
Lower Block
Long Shaft
Heart Rate Monitor/Strap
Drive Belt
Magnet
Clamp
Reed Switch/Wire
Main Wire
Receiver
Handlebar Pivot Bushing
Pivot Axle
M8 Flange Screw
Upright Pivot Bushing
M8 Locknut
Power Receptacle/Wire
Handlebar Cap
Power Adapter
M8 Washer
M4 x 12mm Ground Screw
M8 x 15mm Shoulder Screw
M8 x 18mm Bolt
M8 x 13mm Screw
M10 Jam Nut
M10 x 16mm Screw
M4 x 12mm Screw
M10 x 105mm Screw
M4 x 15mm Screw
M4 x 16mm Screw
M4.5 x 12mm Screw
M4 x 15mm Screw
M8 x 20mm Flat Head Screw
Idler Spring
M4 x 25mm Screw
M8 Nut
M4.2 x 18mm Screw
User’’s Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
30
EXPLODED DRAWING
Model No. EPEX13912.4 R0813A
80
9
13
75
11
85
17
63
60
85
61
85
15
70
75
59
63 70
60
52
74
26
12
70
85
66
10
66
85
72
85
23
27
80
36
74
85
68
70
68
80
25
25
14
4
83
35
75
84
50
46
51
5
16
27
36
78 57 16
6
42
53
73
7
34
76
30
48
80
72
56
73
82
37
81
2
28
77
43
19
18
43
7177
64
55
65
64
77 41
32
1
40
79
3
31
67
58
29
47
32
76
29
31
18
39
49
21
62
38
43
54
41
62
31
71
40
69
43
72
26
64
80
33
22
24
44
55
45
80
8
85
20
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
•• the model number and serial number of the product (see the front cover of this manual)
•• the name of the product (see the front cover of this manual)
•• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.epicfit.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and the eddy mechanism are warranted for
the lifetime of the original purchaser (customer). Parts and labor are warranted for one (1) year from the
date of purchase.
This warranty extends only to the original purchaser (customer). ICON’’s obligation under this warranty is
limited to repairing or replacing, at ICON’’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
or if the product is used for commercial or rental purposes. No other warranty beyond that specically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or prots, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or tness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specic legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 351274 R0813A
Printed in China © 2013 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement