Application Note Topic: Application Note ID: HABH0618080 Vizia RF+™, Wayne-Dalton and HomeLink® integration Version number: 1.0 This Application note will outline how to integrate Wayne Dalton with Z-Wave enabled devices which will enhance energy management and security in the home. Date: 6/18/08 If installing Wayne Dalton devices with a Vizia RF network it is best to use Leviton zone controllers as your 4 button controller device. (VRCZ4-1LX) Author: Ben Hamlitsch Wayne Dalton devices do not communicate the same scene configuration commands as our VRCS4 scene controllers. The status LED’s on the scene controller are inaccurately displayed. This results in a double tap of the scene button before the scene is activated properly. Additionally any devices offered by Wayne Dalton may not be able to understand scene commands from our scene controllers. Product Line: Vizia RF+ For these reasons we recommend Leviton 4 button zone controller VRCZ4 which uses basic set, get commands understood and used by Wayne Daltons Gateway Controller and devices. Product: Primary Remote Wireless Gateway Key fob Remote HomeLink Part Numbers Affected: VRCPG-0SG WDHA-12R (WD) 3150R (WD) Our zone controller may also be setup to turn ON/OFF scenes. (Note: as mentioned above products by Wayne Dalton may not understand scene commands. In these cases program your controller only as a Area ON/OFF) Our zone controller has a toggle on/off style operation as a result there is no double tap in order for the Area or scene to activate. Simply Press the Left side of the toggle button to turn the Area or scene ON or toggle the left side of the button to turn the Area or scene OFF regardless of the status. This operation gives a good user experience when integrating with Wayne Dalton products. When using a Wayne Dalton gateway you will need to setup your zone controller to mirror the same scene or zone activation as the gateway scene button in order for your scenes or zones to synchronize correctly. Example: Wayne Dalton Gateway: Scene Button 1 • Garage Lights 100% • Hall light 100% • Kitchen lights 75% Example: VRCZ4 Zone controller: First, create an Area. Add garage lights, hall lights and kitchen lights to Area “Come Home”. Leviton Manufacturing Co., Inc. 59-25 Little Neck Parkway Little Neck, NY 11362-2591 tech line 800 824-3005 fax 800 832-9538 www.leviton.com This information contained in this document is subject to change at anytime and without further notice. All rights reserved. © Leviton Manufacturing, Inc. Page 2 of 3 Application Note Setup: Button 1: ZONE CONTROLLER ASSOCIATION • AREA>> COME HOME • ACTION>> Area ON/OFF or Scene If scene is selected Press and hold button one to the left side until it flashes green. Set each light in the area to the level desired. In the example above it would be. Garage Lights 100% Hall Lights 100% Kitchen lights 75% Steps to associate and control these devices using our 4 button zone controller. (VRCZ4) Steps: 1. 2. 3. 4. 5. 6. Select >> ASSOCIATION Select zone controller >> CNTRL # 2 Select your button >> BUTTON 1-4 Select your Area/Device >> Node #5/or “COME HOME” Select >> ACTION (assign a scene or Area on/off to button.) Select >> SAVE Once your Vizia RF+ system is setup, you are ready to add the Wireless Home Gateway. Follow the below steps to include the Wireless Home Gateway into your Vizia RF+ Network. Note: Make sure the Wireless Home Gateway is NOT Plugged into AC power when adding it to your network and setting scenes. INCLUDE YOUR GATEWAY On the Vizia RF+ primary remote press MENU. Scroll down to SYSTEM SETUP and select it. Select INSTALLATION CHECKLIST. Select YES to start installation checklist. Scroll down to INCLUDE CONTROLLER. When the primary remote says prepare controller to be included, Press and Hold the COPY and SCENE 1 buttons on the Wireless Home Gateway. After 3 seconds the LED’s will turn ON. Immediately release the COPY and SCENE 1 button on the wireless Home Gateway, the LED’s will blink. Within 20 seconds Press the CENTER button on the Leviton primary remote and the Wireless Home Gateway will be included. Name the Wireless Home Gateway and press the CENTER button on the Leviton primary remote. Your Wireless Home Gateway is now included in your Vizia- RF+ Network. CREATE A SCENE Follow the below steps to create a scene into the Wireless Home Gateway: Note: Make sure the Wireless Home Gateway is NOT Plugged into AC power. On the Wayne Dalton Gateway, Press and Hold the SCENE (1, 2 or 3) button that you wish to program. While holding the SCENE (1, 2 or 3) button press the button on the device you wish to learn, any one of the Vizia RF+ dimmer/switch or Plug-in devices. Note:(the state of the device does Leviton Manufacturing Co., Inc. 59-25 Little Neck Parkway Little Neck, NY 11362-2591 tech line 800 824-3005 fax 800 832-9538 www.leviton.com This information contained in this document is subject to change at anytime and without further notice. All rights reserved. © Leviton Manufacturing, Inc. Page 3 of 3 Application Note matter, if you want to turn on the device it must be off before you learn it in and vice versa) If you are adding a dimmer to the gateway set the dimmer to the desired level. Release the SCENE (1, 2 or 3) button. If you would like multiple devices learned into the same Scene you must repeat these steps for each device. Note: If a Vizia RF+ device does not get included into the scene the first time, press and hold the SCENE button you wish to include it to and add it again into the scene. DELETE A SCENE: Delete a scene by simultaneously press and holding the DELETE button and scene button you wish to reset. After 10 sec the LED on the Gateway will flash (3) times quickly indicating the scene was cleared. Release the buttons. RESET YOUR GATEWAY: Reset your gateway to factory settings by pressing and holding all 3 scene buttons at the same time after 3 sec. the LED’s on the gateway will flash quickly, indicating the memory was cleared. Then release the buttons. INCLUDE AND LEARN KEY FOB TRANSMITTER Follow the steps below to learn your Key fob transmitter into your Wireless Home Gateway. Press and Hold the SCENE (1, 2 or 3) button that you wish to learn the Key fob Transmitter into until the LED turns off then immediately release the SCENE (1, 2 or 3) button Press and Hold the desired Key fob transmitter button that you wish to learn into the SCENE (1, 2 or 3) button. The LED on the Wireless Home Gateway will flash 3 times quickly to indicate the programming was successful. Release the Key fob transmitter button. Repeat the above steps for each Key fob transmitter button that you wish to learn into the Wireless Home Gateway. INCLUDE HOMELINK TRANCIEVER Note: Make sure the Wireless Home Gateway is NOT Plugged into AC power. Follow the steps below to learn your HomeLink Visor transmitter into your Wireless Home Gateway. Place the Wireless Home Gateway within 3 inches of the HomeLink transceiver. Press and Hold the desired HomeLink button until the LED either starts to flash or lights solid (can be up to 30 seconds) Without releasing the HomeLink button, Press and Hold the SCENE (1, 2 or 3) button on the Wireless Home Gateway that you wish to learn. The LED on the Wireless Home Gateway will turn ON and then turn OFF. Keep holding both buttons simultaneously until the HomeLink button LED blinks rapidly or turns off completely (can be up to 60 seconds) Release both buttons, On the Wireless Home Gateway, Press and Hold the SCENE (1, 2 or 3) button that you wish to learn into the HomeLink button until the LED turns off then immediately release the SCENE (1, 2 or 3) button. Press and Hold the desired HomeLink button programmed from above until the LED’s on the Wireless Home Gateway flashes 3 times quickly to indicate the programming was successful Repeat the above steps for each HomeLink button that you wish to learn into the Wireless Home Gateway. Leviton Manufacturing Co., Inc. 59-25 Little Neck Parkway Little Neck, NY 11362-2591 tech line 800 824-3005 fax 800 832-9538 www.leviton.com This information contained in this document is subject to change at anytime and without further notice. All rights reserved. © Leviton Manufacturing, Inc.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021