12

INSTRUCTION GUIDE

CONTENTS

LiPo BATTERY

Rechargeable 3.7v

350mAH LiPo Battery

Screws

Battery tray includes security screw to prevent child access to

LiPo battery. Users over 14 years of age may remove screw from tray for easier access.

RC Stunt Drone

4 Replacement Blades

Remote Control USB Charging Cable Screwdriver

Remove all packaging attachments before giving the toy to a child.

Not suitable for children under 3 years due to small parts that could be swallowed.

Conforms to product safety standards ASTM F963.

Keep instructions for future reference. Do not discard.

™

This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help.

ADULT SUPERVISION REQUIRED

Before each use, an adult should check this product and the LiPo battery to ensure no damage or hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and injury. Pilots are responsible for any actions that result in damage or injury from the improper operation of Drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares and power lines. Never attempt to retrieve Drone from any location higher than your reach (such as rooftops or trees) or from any location that poses a safety hazard. Never fly Drone at night. Keep

Drone in sight at all times during operation. Discontinue operation immediately if Drone flies out of your field of view. Do not fly near spectators or animals. Pets can become excited about R/C vehicles therefore keep away from pets at all times. Keep spinning rotors away from fingers, hair, eyes and other body parts. Always launch from a flat surface. Never leave Drone unattended while it is turned on. Read all enclosed information before operating.

THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 350mAH:

LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may explode, overheat or ignite. Read all following precautions and instructions regarding the care and use of LiPo batteries.  

The enclosed LiPo battery is only to be used with the vehicle and charger included with this product. t

Keep away from flammable materials.

t

Do not expose to direct sunlight.

t

Do not place in fires or leave in hot places.

t

Do not drop or make subject to strong impact.

t

Keep dry and away from water.

t

Remove exhausted batteries as soon as possible and discard properly.

t

Remove all batteries from the compartment if toy is not used for a long period.

t

The supply terminals are not to be short circuited.

t

Never throw batteries in a fire or attempt to open outer casing.

LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be disposed of with other household waste. Check your local laws and regulations for correct recycling and/or battery disposal.

CHANGING DAMAGED PROPELLERS

1

Unplug LiPo battery on Drone.

2

Make note of the blade color and letter (A or

B) before removing the blade from Drone.

(Markings are located on the underside of blades and Drone).

3

Remove the small screw using the mini screwdriver provided.

4

Replace the damaged blade with a new blade with matching color and letter.

Secure the blade with the retaining screw.

B

B

GREEN

BLADES

FRONT

A

A

A

BACK

B

GREY

BLADES

3

4

Bottom View of Drone

A

B

WARNING:

Do not fly with broken or damaged propeller blades as it may cause damage or lead to injury.

ALKALINE BATTERY CAUTIONS

t

Do not use rechargeable batteries.

t

Non-rechargeable batteries are not to be recharged.

t

Different types of batteries or new and old batteries are not to be mixed.

t

Batteries are to be inserted using correct polarity.

t

Remove exhausted batteries as soon as possible and discard properly.

t

Remove all batteries from compartment if toy is not used for a long period.

t

The supply terminals are not to be short-circuited.

t

Never throw batteries in a fire or attempt to open the outer casing.

WARNING:

 Batteries are harmful if swallowed. Please keep away from children.

Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. If you are not able to identify the applicable rules in your area, please check the instructions of the battery manufacturer.

1

1B

MAINTENANCE t

Over time, loose hair or carpet fibers may get wound in blades, reducing performance.

Unplug the Drone and remove fibers from motors. (Remove blades if necessary)

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 1 / PAGE 10

10

ONE TOUCH STUNTS

BARREL ROLL

While flying forward (or reverse), press the STUNT BUTTON.

NOTE: Once a stunt has been initiated,

DO NOT adjust Throttle or press any other controls until the stunt has been completed).

1 2

FRONT BARREL ROLL

FLIP

1

Bring the Drone to a mid air hover without flying in any direction. Remove finger from the DIRECTION STICK

2

While HOVERING, press and hold the

STUNT BUTTON.

3

While still holding the STUNT BUTTON, tap the DIRECTION

STICK in the direction you want to the drone to flip.

RIGHT FLIP LEFT FLIP

REAR BARREL ROLL

1

CHARGING, INSTALLING & CARING FOR

LIPO BATTERY IN THE DRONE

1

Disconnect battery wires.

2

Unscrew the battery screw. Press UP on the button to open the battery compartment door on the rear side of Drone.

3

Pull LiPo battery out of underside of Drone.

Remove LiPo battery from battery case.

4

Plug charging cord into a computer or

USB power block.

5

Plug LiPo battery into Charging Cord.

RED LIGHT = CHARGING

GREEN LIGHT = FULLY CHARGED

6

Charge battery until Full.

7

Once charged, disconnect LiPo battery from USB port.

8

Unplug charging cord from USB power source.

(Always unplug when not in use).

9

Insert LiPo battery into back of Drone. Reconnect the battery wires. Close the battery compartment door.

1

2

3

FRONT FLIP BACK FLIP

2

3

9

CAUTION!

Drone should be flying at least 9 feet in the air with a minimum clearance of 9 feet in all directions before attempting stunt functions.

STUNT FUNCTIONS SHOULD BE PERFORMED OUTSIDE ONLY.

2A

NOTE:

Always unplug LiPo battery when Drone is not in use.

CHARGING PRECAUTIONS:

After use, allow LiPo battery to cool to room temperature before charging.

t

Charge LiPo battery in an isolated area, away from excessive heat or moisture.

t

Never leave LiPo battery unattended while charging.

t

If LiPo battery swells, unplug it immediately and permanently discontinue use.

t

Do not modify, heat, or wet the battery in any way.

t

Only recharge with provided charger.

4

CHARGING

CORD

5

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 9 / PAGE 2

LiPo BATTERY

2

WARNING!

IF AT ANY TIME DURING CHARGING OR USE THE BATTERY BECOMES DAMAGED IN ANY WAY,

DISCONTINUE CHARGING OR USE OF THE BATTERY IMMEDIATELY.

Continuing to charge or discharge a battery that has been damaged can result in a fire.

Quickly and safely disconnect the Drone from charging and place away from flammable materials. Observe the battery for at least 30 minutes to be certain no additional swelling or rupture occurs. Completely discharge the battery by submerging it in a saltwater solution (1/2 cup salt per gallon of water) for 24 hours.

Check your local laws and regulations for correct recycling and/or battery disposal.

WHEN NOT IN USE: t

Always UNPLUG the Drone’s LiPo battery when not in use or when Drone is being stored or transported. t

Store the LiPo battery and Drone in a dry area at room temperature.

t

Avoid temperatures less than 40°F/4°C and greater than 120°F/49°C. t

Do not leave the LiPo battery in a car or exposed to direct sunlight. If exposed to temperatures greater than 120°F/49°C, the LiPo battery can be damaged or may catch fire.

LiPo BATTERY

FLYING TIPS t

When launching the Drone, face the same direction as the Drone. Green blades and

Green LEDs should be front. t

Practice launching, hovering and landing before attempting to learn other moves. t

Flying 2 to 3 feet above the ground will reduce ground turbulence and make flying easier. t

When first attempting to fly in different directions, start by tapping the Direction stick until you have a feel for it. Always move controls slowly until you become comfortable operating the Drone. t

Once you’ve mastered flying in directions, practice rotational controls. Spinning and keeping Drone facing the same direction you are facing makes flying easier and more intuitive.

t

Stay 2 to 3 feet away from walls and ceilings as Drone will be drawn towards them if you fly too close. t

If propeller blades come in contact with another object or you crash, throttle down immediately to prevent possible or further damage.

t

If anything prevents Drone’s blades from spinning or they become jammed,

THROTTLE

DOWN IMMEDIATELY. Do not attempt to fly until obstruction has been removed and damage fixed.

t

Should something prevent Drone’s blades from spinning, Drone may

AUTO SHUTDOWN. LiPo battery will need to be unplugged then reconnected to restore flying power.

t If the Drone flies too far away, beyond the control range of the remote, the Drone will

AUTO-LAND to prevent the Drone from flying away out of control.

INSTALLING REMOTE BATTERIES

Loosen screw in the Remote Control battery compartment door with Philips screw driver and insert batteries as shown. Replace door and tighten screw.

4 x

–

–

+

+

1.5 V

AAA (LR03)

1.5 V

AAA (LR03)

1.5 V

AAA (LR03)

1.5 V

AAA (LR03)

+

+

–

–

+ AAA/LR03/R03 1.5V –

– AAA/LR03/R03 1.5V +

+ AAA/LR03/R03 1.5V –

– AAA/LR03/R03 1.5V +

AUTO SHUTDOWN: t

If battery voltage drops to an extremely low level, Drone will automatically shutdown.

The Stunt Drone will need to be recharged to restore flying power.

t

If anything prevents Drone’s blades from spinning or they become jammed, Drone will automatically shutdown. The LiPo battery will need to be unplugged, then reconnected to restore flying power.

3

2B

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 3 / PAGE 8

8

4

5

FLIGHT SENSITIVITY ADJUSTMENT

Drone responsiveness may be adjusted on the

Controller to match your flying skills.

There are three choices:

1. LOW – 2. MEDIUM – 3. HIGH SENSITIVITY

It is best to start in

LOW POSITION until you have mastered flying.

Flight sensitivity can be adjusted before or during flight.

1 - LOW 2 - MEDIUM 3 - HIGH

TRIM ADJUSTMENTS

1

If Drone drifts in any direction while hovering (and you are not pressing the

Direction stick), you may need to make trim adjustments. Safely land Drone on a level surface. Press the recommended Trim button once as described below. Launch Drone back into the air and attempt another still hover. If

Drone continues to drift, repeat the process until the Drone hovers in place:

2

3

t

Drone drifts forward (Fig. 1)

– Press the B button t

Drone drifts backward (Fig. 2)

– Press the F button t

Drone drifts to the left (Fig. 3)

– Press the R button t

Drone drifts to the right (Fig. 4)

– Press the L button t

Drone spins counter-clockwise, when viewed from the top (Fig. 5)

– Press the button t

Drone spins clockwise, when viewed from the top (Fig. 6)

– Press the button

6

NOTE: THE REMOTE WILL BEEP/FLASH 3

TIMES WHEN TRIM ADJUSTMENT IS SET TO

THE NEUTRAL POSITION (THE MIDDLE OF THE

TRIM RANGE) AND BEEP ONCE WHEN IT HAS

REACHED THE END OF IT’S RANGE.

7

3A

CALIBRATING & LAUNCHING

1

Press to turn

OFF Remote Control.

2

Unplug the Drone LiPo battery.

Disconnect by pulling connectors apart—

Do not pull wires.

3

Reconnect Drone LiPo battery.

4

Quickly place Drone on FLAT LEVEL

SURFACE.

5

Press to turn Remote Control

ON.

6

Slowly push remote control THROTTLE

STICK UP until Drone lifts into the air.

1

2

IMPORTANT: YOU ONLY HAVE A FEW

SECONDS AFTER THE LIPO BATTERY IS

PLUGGED IN TO PLACE DRONE ON A

LEVEL SURFACE FOR PROPER CALIBRA-

TION. IF DRONE DOES NOT RISE TO A

STABLE HOVER OR FLIES ERRATICALLY,

REPEAT STEPS 1 THROUGH 6.

3

CAUTION: NEVER APPROACH DRONE

WHILE THE PROPELLER BLADES ARE

STILL SPINNING. THROTTLE DOWN UNTIL

THE BLADES STOP THEN TURN OFF

REMOTE BEFORE ATTEMPTING TO

HANDLE DRONE.

4

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 7 / PAGE 4

5

6

4

FLIGHT CONTROLS

Familiarize yourself with Drone’s controls before flying!

Press UP to lift

THROTTLE/ROTATION STICK

t

To make the Drone

LIFT, push the throttle stick FORWARD.

t

The further you PUSH the throttle stick, the faster you LIFT.

t

To make the Drone

HOVER, find the sweet spot on the throttle stick

(somewhere in the middle).

Forward/Backward Trim

Power On/Off Switch

Power indicator LED

STUNT Button

Press DOWN to descend

THROTTLE/

ROTATION STICK

DIRECTION STICK

Press UP to fly forward

Press DOWN to fly backward

Press LEFT to rotate counter-clockwise

5

3B

Press RIGHT to rotate clockwise

Rotation Trim

Flight Sensitivity Switch

Left/Right Trim

DIRECTION STICK

t

Push the Direction stick

FORWARD to fly forward or away from you (Green blades in front)

Push

BACKWARD to fly backward.

The farther you push, the faster Drone flies in that direction.

t

Push the Direction stick

LEFT to fly left. Push RIGHT to fly right.

The farther you push, the faster Drone flies sideways.

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 5 / PAGE 6

Press LEFT to fly left

Press RIGHT to fly right

6

FLIGHT CONTROLS

Familiarize yourself with Drone’s controls before flying!

Press UP to lift

THROTTLE/ROTATION STICK

t

To make the Drone

LIFT, push the throttle stick FORWARD.

t

The further you PUSH the throttle stick, the faster you LIFT.

t

To make the Drone

HOVER, find the sweet spot on the throttle stick

(somewhere in the middle).

Forward/Backward Trim

Power On/Off Switch

Power indicator LED

STUNT Button

Press DOWN to descend

THROTTLE/

ROTATION STICK

DIRECTION STICK

Press UP to fly forward

Press DOWN to fly backward

Press LEFT to rotate counter-clockwise

5

3B

Press RIGHT to rotate clockwise

Rotation Trim

Flight Sensitivity Switch

Left/Right Trim

DIRECTION STICK

t

Push the Direction stick

FORWARD to fly forward or away from you (Green blades in front)

Push

BACKWARD to fly backward.

The farther you push, the faster Drone flies in that direction.

t

Push the Direction stick

LEFT to fly left. Push RIGHT to fly right.

The farther you push, the faster Drone flies sideways.

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 5 / PAGE 6

Press LEFT to fly left

Press RIGHT to fly right

6

4

5

FLIGHT SENSITIVITY ADJUSTMENT

Drone responsiveness may be adjusted on the

Controller to match your flying skills.

There are three choices:

1. LOW – 2. MEDIUM – 3. HIGH SENSITIVITY

It is best to start in LOW POSITION until you have mastered flying.

Flight sensitivity can be adjusted before or during flight.

1 - LOW 2 - MEDIUM 3 - HIGH

TRIM ADJUSTMENTS

1

If Drone drifts in any direction while hovering (and you are not pressing the

Direction stick), you may need to make trim adjustments. Safely land Drone on a level surface. Press the recommended Trim button once as described below. Launch Drone back into the air and attempt another still hover. If

Drone continues to drift, repeat the process until the Drone hovers in place:

2

3

t

Drone drifts forward (Fig. 1)

– Press the B button t

Drone drifts backward (Fig. 2)

– Press the F button t

Drone drifts to the left (Fig. 3)

– Press the

R button t

Drone drifts to the right (Fig. 4)

– Press the

L button t

Drone spins counter-clockwise, when viewed from the top (Fig. 5)

– Press the button t

Drone spins clockwise, when viewed from the top (Fig. 6)

– Press the button

6

NOTE: THE REMOTE WILL BEEP/FLASH 3

TIMES WHEN TRIM ADJUSTMENT IS SET TO

THE NEUTRAL POSITION (THE MIDDLE OF THE

TRIM RANGE) AND BEEP ONCE WHEN IT HAS

REACHED THE END OF IT’S RANGE.

7

3A

CALIBRATING & LAUNCHING

1

Press to turn OFF Remote Control.

2

Unplug the Drone LiPo battery.

Disconnect by pulling connectors apart—

Do not pull wires.

3

Reconnect Drone LiPo battery.

4

Quickly place Drone on FLAT LEVEL

SURFACE.

5

Press to turn Remote Control ON.

6

Slowly push remote control THROTTLE

STICK UP until Drone lifts into the air.

1

2

IMPORTANT: YOU ONLY HAVE A FEW

SECONDS AFTER THE LIPO BATTERY IS

PLUGGED IN TO PLACE DRONE ON A

LEVEL SURFACE FOR PROPER CALIBRA-

TION. IF DRONE DOES NOT RISE TO A

STABLE HOVER OR FLIES ERRATICALLY,

REPEAT STEPS 1 THROUGH 6.

3

CAUTION: NEVER APPROACH DRONE

WHILE THE PROPELLER BLADES ARE

STILL SPINNING. THROTTLE DOWN UNTIL

THE BLADES STOP THEN TURN OFF

REMOTE BEFORE ATTEMPTING TO

HANDLE DRONE.

4

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 7 / PAGE 4

5

6

4

Drone responsiveness may be adjusted on the

Controller to match your flying skills.

There are three choices:

Continuing to charge or discharge a battery that has been damaged can result in a fire.

1. LOW – 2. MEDIUM – 3. HIGH SENSITIVITY materials. Observe the battery for at least 30 minutes to be certain no additional swelling or rupture occurs. Completely discharge the battery by submerging it in a saltwater solution (1/2 cup salt per gallon of water) for 24 hours.

Flight sensitivity can be adjusted before or during flight.

TRIM ADJUSTMENTS

1 - LOW 2 - MEDIUM 3 - HIGH

WHEN NOT IN USE: t

Always UNPLUG the Drone’s LiPo battery when not in use or when Drone is being stored or transported. t t

1

2

Store the LiPo battery and Drone in a dry area at room temperature.

Avoid temperatures less than 40°F/4°C and greater than 120°F/49°C.

Do not leave the LiPo battery or may catch fire.

in a car or exposed to direct sunlight. If exposed to temperatures greater than 120°F/49°C, the LiPo battery can be damaged t

Drone drifts forward (Fig. 1)

– Press the B button t

Drone drifts backward (Fig. 2)

INSTALLING REMOTE BATTERIES

3

t

Drone drifts to the left (Fig. 3)

– Press the

R button insert batteries as shown. Replace door and tighten screw.

t

Drone drifts to the right (Fig. 4)

– Press the

L button

+ AAA/LR03/R03 1.5V –

4

4 x

–

+

+ t t

+

–

– Press the button

Drone spins clockwise, when viewed from the top (Fig. 6)

– button

+ AAA/LR03/R03 1.5V –

5

–

1.5 V

AAA (LR03)

+

AUTO SHUTDOWN: t

6

NOTE: THE REMOTE WILL BEEP/FLASH 3

TIMES WHEN TRIM ADJUSTMENT IS SET TO

THE NEUTRAL POSITION (THE MIDDLE OF THE

If battery voltage drops to an extremely low level, Drone will automatically shutdown.

REACHED THE END OF IT’S RANGE. t

If anything prevents Drone’s blades from spinning or they become jammed, Drone will automatically shutdown. The LiPo battery will need to be unplugged, then reconnected to restore flying power.

1

2

Press to turn OFF Remote Control.

Unplug the Drone LiPo battery. t

Practice launching, hovering and landing before attempting to learn other moves.

3

Reconnect Drone LiPo battery.

4

Quickly place Drone on FLAT LEVEL t

5

1

When first attempting to fly in different directions, start by tapping the Direction stick until you have a feel for it. Always move controls slowly until you become comfortable

Press to turn Remote Control ON.

6

Slowly push remote control THROTTLE intuitive.

2

t

Stay 2 to 3 feet away from walls and ceilings as Drone will be drawn towards them if you fly too close. t

If propeller blades come in contact with another object or you crash, throttle down t

PLUGGED IN TO PLACE DRONE ON A

If anything prevents Drone’s blades from spinning or they become jammed,

3

THROTTLE

DOWN IMMEDIATELY. Do not attempt to fly until obstruction has been removed and

REPEAT STEPS 1 THROUGH 6.

t

Should something prevent Drone’s blades from spinning, Drone may

AUTO SHUTDOWN. LiPo battery will need to be unplugged then reconnected to restore flying power.

t If the Drone flies too far away, beyond the control range of the remote, the Drone will

4

REMOTE BEFORE ATTEMPTING TO

HANDLE DRONE.

5

6

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 3 / PAGE 8

ONE TOUCH STUNTS

BARREL ROLL

While flying forward (or reverse), press the

STUNT BUTTON.

NOTE: Once a stunt has been initiated,

DO NOT adjust Throttle or press any other controls until the stunt has been completed).

1 2

FRONT BARREL ROLL

FLIP

1

Bring the Drone to a mid air hover without flying in any direction. Remove finger from the DIRECTION STICK

2

While HOVERING, press and hold the STUNT BUTTON.

3

While still holding the

STUNT BUTTON, tap the DIRECTION

STICK in the direction you want to the drone to flip.

RIGHT FLIP LEFT FLIP

REAR BARREL ROLL

1

CHARGING, INSTALLING & CARING FOR

LIPO BATTERY IN THE DRONE

1

Disconnect battery wires.

2

Unscrew the battery screw. Press UP on the button to open the battery compartment door on the rear side of Drone.

3

Pull LiPo battery out of underside of Drone.

Remove LiPo battery from battery case.

4

Plug charging cord into a computer or

USB power block.

5

Plug LiPo battery into Charging Cord.

RED LIGHT = CHARGING

GREEN LIGHT = FULLY CHARGED

6

Charge battery until Full.

7

Once charged, disconnect LiPo battery from USB port.

8

Unplug charging cord from USB power source.

(Always unplug when not in use).

9

Insert LiPo battery into back of Drone. Reconnect the battery wires. Close the battery compartment door.

1

2

3

FRONT FLIP BACK FLIP

2

3

9

CAUTION!

Drone should be flying at least 9 feet in the air with a minimum clearance of 9 feet in all directions before attempting stunt functions.

STUNT FUNCTIONS SHOULD BE PERFORMED OUTSIDE ONLY.

2A

NOTE:

Always unplug LiPo battery when Drone is not in use.

CHARGING PRECAUTIONS:

After use, allow LiPo battery to cool to room temperature before charging.

t

Charge LiPo battery in an isolated area, away from excessive heat or moisture.

t

Never leave LiPo battery unattended while charging.

t

If LiPo battery swells, unplug it immediately and permanently discontinue use.

t

Do not modify, heat, or wet the battery in any way.

t

Only recharge with provided charger.

4

CHARGING

CORD

5

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 9 / PAGE 2

LiPo BATTERY

2

ADULT SUPERVISION REQUIRED

Before each use, an adult should check this product and the LiPo battery to ensure no damage or hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and injury. Pilots are responsible for any actions that result in damage or injury from the improper operation of Drone. Adequate flying space is required. Avoid flying near interior fans and/or vents as they may make flying difficult to control. Keep a safe distance away from streets, public thoroughfares and power lines. Never attempt to retrieve Drone from any location higher than your reach (such as rooftops or trees) or from any location that poses a safety hazard. Never fly Drone at night. Keep

Drone in sight at all times during operation. Discontinue operation immediately if Drone flies out of your field of view. Do not fly near spectators or animals. Pets can become excited about R/C vehicles therefore keep away from pets at all times. Keep spinning rotors away from fingers, hair, eyes and other body parts. Always launch from a flat surface. Never leave Drone unattended while it is turned on. Read all enclosed information before operating.

THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY 3.7V 350mAH:

LiPo batteries have a severe risk of fire and injury if they are improperly handled or misused. They may explode, overheat or ignite. Read all following precautions and instructions regarding the care and use of LiPo batteries.  

The enclosed LiPo battery is only to be used with the vehicle and charger included with this product. t

Keep away from flammable materials.

t

Do not expose to direct sunlight.

t

Do not place in fires or leave in hot places.

t

Do not drop or make subject to strong impact.

t

Keep dry and away from water.

t

Remove exhausted batteries as soon as possible and discard properly.

t

Remove all batteries from the compartment if toy is not used for a long period.

t

The supply terminals are not to be short circuited.

t

Never throw batteries in a fire or attempt to open outer casing.

LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be disposed of with other household waste. Check your local laws and regulations for correct recycling and/or battery disposal.

CHANGING DAMAGED PROPELLERS

1

Unplug LiPo battery on Drone.

2

Make note of the blade color and letter (A or

B) before removing the blade from Drone.

(Markings are located on the underside of blades and Drone).

3

Remove the small screw using the mini screwdriver provided.

4

Replace the damaged blade with a new blade with matching color and letter.

Secure the blade with the retaining screw.

B

B

GREEN

BLADES

FRONT

A

A

A

BACK

B

GREY

BLADES

3

4

Bottom View of Drone

A

B

WARNING:

Do not fly with broken or damaged propeller blades as it may cause damage or lead to injury.

ALKALINE BATTERY CAUTIONS

t

Do not use rechargeable batteries.

t

Non-rechargeable batteries are not to be recharged.

t

Different types of batteries or new and old batteries are not to be mixed.

t

Batteries are to be inserted using correct polarity.

t

Remove exhausted batteries as soon as possible and discard properly.

t

Remove all batteries from compartment if toy is not used for a long period.

t

The supply terminals are not to be short-circuited.

t

Never throw batteries in a fire or attempt to open the outer casing.

WARNING:

 Batteries are harmful if swallowed. Please keep away from children.

Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. If you are not able to identify the applicable rules in your area, please check the instructions of the battery manufacturer.

1

1B

MAINTENANCE t

Over time, loose hair or carpet fibers may get wound in blades, reducing performance.

Unplug the Drone and remove fibers from motors. (Remove blades if necessary)

SIZE: 297 x 210mm (folds to 148.5 x 210mm)

PAGE 1 / PAGE 10

10

TROUBLESHOOTING

PROBLEM

Drone is unresponsive or behaving erratically

SOLUTION

t

Drone may be miscalibrated by launching from an unlevel surface. Turn the remote off and unplug Drone’s battery for

30 seconds then turn them back on and try again from a flat, level launching surface.

t

Ensure your remote is within unobstructed view of Drone and you are within 30 feet range.

t

Ensure the remote has fresh batteries and the LiPo battery is fully charged.

t

Inspect Drone for any possible damage. Turn the remote off and unplug Drone’s battery for 30 seconds then turn them back on and try again from a flat, level launching surface.

All blades spin, but Drone will not fly properly.

t

Drone’s blades may have been installed incorrectly. Reinstall and remember that the GREEN blades point forward.

Drone drifts in any direction during flight without direction from the remote

Drone crashes immediately

Drone crashes when attempting stunt functions t

Adjust the trim controls until drifting ceases, see page 7.

t

Propellers may be installed in the wrong position. Ensure proper installation.

t

Ensure that is flying a minimum distance of 9 feet from the ground with a minimum 9 feet clearance in all directions.

www.skyrockettoys.com/products/sky-viper

Customer Service :

888-674-5650

™

©2015 Skyrocket Toys LLC, Los Angeles, CA 90066 USA. All Rights Reserved.

Sky Viper is a registered tradmark and the Skyrocket logo are trademarks of Skyrocket Toys LLC.

MADE IN CHINA.