SINGER 1507 Instruction manual
SINGER 1507 is a user-friendly sewing machine with a variety of features that make sewing simple and enjoyable. It offers 23 built-in stitches, including basic, stretch, and decorative stitches, allowing you to tackle a wide range of projects. The machine also features an automatic needle threader, adjustable stitch length and width, and a reverse sewing function for added convenience. Additionally, the SINGER 1507 has a two-step presser foot lifter, making it easy to sew multiple layers of fabric or thick materials.
Reklama
Reklama
Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety should always 6. Always use the proper needle plate, The wrong plate can be followed, including the following: cause the needle to break.
Read all instructions before using this sewing machine.
DANGER
- To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
3. Always unplug before re-lamping. Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area).
WARNING
- To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or near children.
2. Use this appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air openings blocked.
Keep ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth.
5. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
9. Switch the sewing machine off ("O") when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, and the like.
10.Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.
11.Never drop or insert any object into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol spray products are being used or where oxygen is being administered.
14.To disconnect, turn all controls to the off ("O") position, then remove plug from outlet.
15.Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
16.The sound pressure level under normal operating conditions is 75 B(A).
SAVE THESE INSTRUCTIONS
This sewing machine is intended for household use only.
Congratulations
As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity.
From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made.
May we recommend that, before you start to use your sewing machine, you discover the many advantages and the ease of operation by going through this instruction book, step by step, seated at your machine.
To ensure that you are always provided with the most modern sewing capabilities, the manufacturer reserves the right to change the appearance, design or accessories of this sewing machine when considered necessary.
SINGER IS A REGISTERED TRADEMARK OF THE SINGER COMPANY LIMITED OR ITS AFFILIATES
COPYRIGHT © 2005
All rights reserved throughout the world.
List of contents
Principal parts of the machine ..................................................2/3
Accessories .................................................................................4
Installing the snap-in sewing table ..............................................5
Connecting machine to power source .........................................6
Changing the bulb .......................................................................7
Two-step presser foot lifter..........................................................8
Adjusting presser foot pressure...................................................8
Attaching the presser foot holder ................................................9
Winding the bobbin....................................................................10
Inserting the bobbin...................................................................11
Inserting and changing needles ................................................12
Threading the upper thread.......................................................13
Automatic needle threader (optional) ........................................14
Thread tension ..........................................................................15
Raising the bobbin thread .........................................................16
Reverse sewing/ Removing the work/ Cutting the thread .........17
Matching needle/ fabric/ thread .................................................18
How to choose your pattern ......................................................19
Straight stitch and needle position ...........................................20
Zig-zag stitching ........................................................................21
Blind hem/ Lingerie stitch .........................................................22
Sewing on buttons.....................................................................23
Sew 4-step buttonholes.............................................................24
Zippers and piping.....................................................................25
Mutlti-stitch zig-zag/ Bar tack ....................................................26
Free motion darning, stippling ...................................................27
Practical stitches ......................................................................28
Applique and blindstitch applique..............................................29
Quilting functions.......................................................................30
Mending.....................................................................................31
Stay-stitching.............................................................................32
Blindstitch applique ...................................................................33
Traditional pintucks ...................................................................34
Gathering...................................................................................35
Couching ...................................................................................36
Trim attachment stitch function .................................................37
Maintenance..............................................................................38
Trouble shooting guide..............................................................39
Principal parts of the machine
1. Thread tension dial
2. Presser foot pressure adjustment
3. Thread take-up lever
4. Thread cutter
5. Presser foot
6. Needle plate
7. Removable sewing table/ accessory storage
8. Reverse sewing lever
9. Bobbin stopper
10. Stitch length dial
11. Pattern selector dial
12. Automatic threader (optional)
1
2
3
4
5
6
7
2
12
8
9
10
11
Principal parts of the machine
13. Horizontal spool pin
14. Bobbin winder
15. Handwheel
16. Power and light switch
17. Main plug socket
18. Bobbin thread guide
19. Upper thread guide
20. Face plate
21. Handle
22. Presser foot lever
23. Foot speed control
24. Power cord
13
14
15
16
17
3
23
24
18
19
20
21
22
Accessories
Standard accessories (1)
a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. L-screwdriver f. Seam ripper/ brush g. Oil bottle h. Pack of needles
I. Bobbin (3x) j. Seam guide k. Darning plate l. Spool holder
1 a b e
006806008
f
006905008
c
006909008
g h d
006914008
i
Optional accessories (2)
(These 6 accessories are not supplied with this machine; they are however available as special accessories from your local dealer.) m.Satin stitch foot n. Overcasting foot o. Hemmer foot p. Blind hem foot q. Cording foot r. Darning foot
2 m p
006916008
006812008
4
j k n q
006803008
006804008
l o r
006800008
006016008
Installing the snap-in sewing table
Keep the snap-in sewing table horizontal, and push it in the direction of the arrow. (1)
The inside of the snap-in sewing table can be utilized as an accessory box.
To open, lift up at the point of the arrow. (2)
1
5
2
Connecting machine to power source
Connect the machine to a power source as illustrated. (1)
This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2)
Attention:
Unplug power cord when machine is not in use.
Foot control
The foot control pedal regulates the sewing speed. (3)
Attention:
Consult a qualified electrician if in doubt as to connect machine to power source. Unplug power cord when machine is not in use.
The foot control must be used with the appliance by KD-1902
(110-120V area)/ KD-2902 (220-240V area) manufactured by
ZHEJIANG FOUNDER MOTOR CORPORATION LTD. (China)
Sewing light
Press main switch (A) for power and light on " l ".
1
Polarized attachment plug
IMPORTANT NOTICE
For appliance with a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If it does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.
6
2
Conductor intended to be grounded
3
A
Changing the bulb
Disconnect the machine from the power supply by removing the plug from the main socket!
Replace bulb with same type rated 10 watts (110-120V area) or
15 watts (220-240V area).
- Loosen screw (A) as illustrated. (1)
- Remove the face plate (B).
- Unscrew the bulb and install a new one (C). (2)
- Replace the face plate and tighten screw.
Should there be any problem, ask your local dealer for advice.
1
A
B
C
7
2
Two-step presser foot lifter
When sewing several layers or thick fabrics, the presser foot can be raised work. (A)
to a high rise position for easy positioning of the
Adjusting presser foot pressure
The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of fabric (light-or-heavy weight).
However, if you need to adjust the presser foot pressure, turn the presser adjusting screw with a coin.
For sewing very thin fabric, loosen the pressure by turning the screw counter counterclockwise turning it clockwise.
, and for heavy fabric, tighten by
8
A
Attaching the presser foot holder
Raise the presser bar (a). Attach the presser foot shank (b) as illustrated. (1)
Attaching the presser foot
Lower the presser foot shank (b) until the cut-out (c) is directly above the pin (d). (2)
Raise the lever (e).
Lower the presser foot shank (b) and the presser foot (f) will engage automatically.
Removing the presser foot
Raise the presser foot. (3)
Raise the lever (e) and the foot disengages.
1
Attaching the seam guide
Attach the seam guide (g) in the slot as illustrated.
Adjust according to need for hems, pleats, etc. (4)
Attention:
Turn power switch to off ("O") when carrying out any of the above operations!
e a b
9
3 a
2 e b d c f
4 g
Winding the bobbin
- Place thread and spool holder onto spool pin (1).
- For smaller spools of thread place spool holder with small side next to spool (2).
- Wind thread anticlockwise around bobbin winder tension discs (3).
- Thread bobbin as illustrated and place on spindle (4).
- Push bobbin to right (5).
- Hold thread end (6).
- Step on foot control pedal (7).
- Cut thread (8).
- Press bobbin to left (9) and remove.
1
2
Please Note:
When the bobbin winder spindle is in "bobbin winding" position, the machine will not sew and the hand wheel will not turn. To start sewing, push the bobbin winder spindle to the left (sewing position).
3
6
10
7
4
8
5
9
Inserting the bobbin
When inserting or removing the bobbin, the needle must be fully raised.
- Open the hinged cover (1).
- Hold the bobbin case with one hand. Insert the bobbin so that the thread runs in a clockwise direction (arrow) (2).
- Pull the thread through the slit and under the finger (3).
- Hold the bobbin case by the hinged latch (4).
- Insert it into the shuttle (5).
Attention:
Turn power switch to off ("O") before inserting or removing the bobbin.
3
1 2
4
11
5
Inserting and changing needles
Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results always use
SINGER Brand Needles.
Insert the needle as illustrated as follows:
A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1)
B. The flat side of the shaft should be towards the back.
C/D. Insert the needle as far up as it will go.
Attention:
Turn power switch to off ("O") before inserting or removing the needle.
1
Needles must be in perfect condition. (2)
Problems can occur with:
A. Bent needles
B. Blunt needles
C. Damaged points
12
2
C
A
D
B
B A C
Threading the upper thread
This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result.
- Start by raising the needle to its highest point (1), and also raise the presser foot to release the tension discs. (2)
Note: For safety, it is strongly suggested you turn off the power before threading.
- Lift up the spool pin. Place the spool of thread on the holder with the thread coming off the spool as shown. For small thread spools, place small side of spool holder next to spool.(3)
- Draw thread from spool through the upper thread guide. (4)
- Guide thread around thread guide (5) pulling thread through pretension spring as illustrated.
- Thread tension module by leading thread down right channel and up left channel (6). During this process it is helpful to hold the thread between the spool and thread guide (4).
- At the top of this movement pass thread from right to left through the slotted eye of the take-up lever and then downwards again. (7)
Now pass thread behind the thin wire needle clamp guide (8) and then down to the needle which should be threaded from front to back.
- Pull about 6-8 inches of thread to the rear beyond the needle eye. Trim thread to length with built in thread cutter. (9)
2
8
6
7
Note:
If your sewing machine is equipped with the factory installed optional automatic needle threader, instructions for use can be found on page 14.
13
5 6
3
4
5
2
7
3
4
8
1
Automatic needle threader (optional)
* The automatic needle threader is a factory installed option. If your machine has this option use the following instructions:
- Raise the needle to its highest position.
- Press lever (A) down as far as it will go.
- The threader automatically swings to the threading position (B).
- Pass thread around thread guide (C).
- Pass the thread in front of the needle around the hook (D) from bottom to top.
- Release lever (A).
- Pull the thread through the needle eye.
1
Attention:
Turn power switch to off ("O")!
A
C
A
B
B
D
C
D
A
14
2
Thread tension
Upper thread tension
Basic thread tension setting: "4"
To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down.
A. Normal thread tension for straight stitch sewing.
B. Thread tension too loose for straight stitch sewing. Turn dial to higher number.
C. Thread tension too tight for straight stitch sewing. Turn dial to lower number.
D. Normal thread tension for zig zag and decorative sewing.
Correct thread tension is when a small amount of the upper thread appears on the bottom side of fabric.
Lower thread tension
To test the bobbin thread tension, remove the bobbin case and bobbin and hold it by suspending it by the thread. Jerk it once or twice. If the tension is correct, the thread will unwind by about an inch or two. If the tension is too tight, it does not unwind at all. If the tension is too loose, it will drop too much. To adjust, turn the small screw on the side of the bobbin case.
1
Please note:
- Proper setting of tension is important to good sewing.
- There is no single tension setting appropriate for all stitch functions, thread or fabric.
- A balanced tension (identical stitches both top and bottom) is usually only desirable for straight stitch construction sewing.
- 90% of all sewing will be between "3" and "5".
- For zig zag and decorative sewing stitch functions, thread tension should generally be less than for straight stitch sewing.
- For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the upper thread appears on the bottom side of your fabric.
A
15
C
2
B
D
4
Raising the bobbin thread
Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle.
Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole (2).
1
Lay both threads to the back under the presser foot. (3)
16
2 3
Reverse sewing
To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forwards again. (1)
A
Removing the work
Turn the handwheel counterclockwise to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot.
(2)
1
Cutting the thread
Pull the threads behind the presser foot. Guide the threads to the side of the face plate and into thread cutter (B). Pull threads down to cut. (3)
B
17
3
2
Matching needle/ fabric/ thread
NEEDLE, FABRIC, THREAD SELECTION GUIDE
NEEDLE SIZE
9-11 (70-80)
FABRICS
Lightweight fabrics-thin cottons, voile, serge, silk , muslin,
Qiana, interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics.
THREAD
Light-duty thread in cotton, nylon ,polyester or cotton wrapped polyester.
11-14 (80-90)
14 (90)
16 (100)
18 (110)
Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits, lightweight woollens.
Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.
Most threads sold are medium size and suitable for these fabrics and needle sizes. Use polyester threads on synthetic materials and cotton on natural woven fabrics for best results.
Always use the same thread on top and bottom.
Heavyweight fabrics-canvas, woolens, outdoor tent and quilted fabrics, denims, upholstery material (light to medium).
Heavy woollens, overcoat fabrics, upholstery fabrics, some leathers and vinyls.
Heavy duty thread, carpet thread. (Use heavy foot pressure-large numbers.)
IMPORTANT:
Match needle size to thread size and weight of fabric.
NEEDLE, FABRIC SELECTION
NEEDLES
SINGER
2020
EXPLANATION TYPE OF FABRIC
Standard sharp needles. Sizes range thin to large. 9 (70) to 18 (110).
Natural woven fabrics-wool, cotton, silk, etc. Qiana. Not recommended for double knits.
SINGER
2045
SINGER
Semi-ball point needle, scarfed. 9 (70) to
18 (110).
Twin Needle.
Natural and synthetic woven fabrics, polyester blends. Knits-polyesters, interlocks, tricot, single and double knits. Also sweater knits, Lycra, swimsuit fabric, elastic.
Woven fabrics and knits.
SINGER Leather needles. 12 (80) to 18 (110) Leather, vinyl, upholstery. (Leaves smaller hole than standard large needle.)
Note twin needle:
1. Twin needles, can be purchased for utility and decorative work.
2. When sewing with twin needles, the stitch width dial should be set at less than "3".
3. For best sewing results always use genuine SINGER needles.
4. Replace needle often (approximately every other garment ) and/ or at first thread breakage or skipped stitches.
18
How to choose your pattern
For center needle straight stitch select pattern " " with pattern selector dial. Adjust the stitch length with the stitch length dial.
You may choose left needle position, by selecting pattern " ".
For zigzag stitch, select pattern " " with pattern selector dial.
Adjust the stitch length according to the fabric being used.
To obtain any of the other patterns shown on the stitch selection panel, select the stitch with the pattern selector dial.
Adjust the stitch length with the stitch length dial.
a b c
a. Reverse sewing lever b. Stitch length dial c. Pattern selector dial
19
3
4
2
1
Straight stitching and needle position
Turn the stitch selection dial so that the pointer is set to the straight stitch position.
Choose your needle position, from center needle position or right needle position.
Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be. For a fine stitch set length at "1" or "2".
For gathering set to straight stitch, with stitch length at "4".
Do 2 rows of stitching ¼ of an inch apart. Remove from machine, hold bobbin thread and gather fabric to desired fullness.
Topstitching
Topstitching is used to embellish a variety of projects. Sew 1/4 of an inch from the edge of your garment or seam to topstitch.
Turn the stitch selection dial so that the pointer is set to the straight stitch position. Choose center needle position.
For topstitching variable stitch length can be used. Use the all purpose foot to perform this function.
20
4 3 2 1 0.5
4
3
2
1
0
Zig-zag stitching
Turn the pattern selector dial to " ". (1)
Function of stitch length dial while zigzaging
The density of zigzag stitches increase as the setting of stitch length dial approaches "0".
Neat zigzag stitches are usually achieved at "2.5" or below.
Dense zigzag stitches (close together) are referred to as a satin stitch. (2)
21
1
4 3 2 1 0.5
4
3
2
1
0
2
Blind hem/ Lingerie stitch
For hems, curtains, trousers, skirts, etc.
Blind hem for stretch fabrics.
Blind hem/ lingerie for firm fabrics.
Reverse blind hem/ lingerie for firm fabrics.
Note:
It takes practice to sew blind hems. Always make a sewing test first.
Turn up the hem to the desired width and press. Fold back (as shown in Fig. 1) against the right side of the fabric with the top edge of the hem extending about 5 mm. (1/5") to the right side of the folded fabric.
Start to sew slowly on the fold, making sure the needle touches slightly the folded top to catch one or two fabric threads (2).
Unfold the fabric when hemming is completed and press.
1
2
4
3
2
1
0
22
Sewing on buttons
Install the darning plate. (1)
Change presser foot to button sewing foot (2).
Position the work under the foot.
Place the button in the desired position and lower the foot.
Set the pattern selector knob on " " and sew a few securing stitches. Select one of the two narrow zig zag patterns according to the distance between the two holes of the button. Turn the handwheel to check if the needle goes into the right and the left hole of the button without hitting the button.
Slowly sew on the button with about 10 stitches.
Select pattern " " and sew a few securing stitches (3).
If a shank is required, place a darning needle on top of the button and sew (4). For buttons with 4 holes, sew through the front two holes first (3), push the work forward and then sew through the back two holes (4).
1
23
2
3
Sew 4-step buttonholes
Prepare
1. Take off the all purpose foot and attach the buttonhole foot.
2. Measure diameter and thickness of button and add 0.3 cm
(1/8") for bar tacks; mark buttonhole size on fabric.
3. Place fabric under the foot, so that marking on the buttonhole foot aligns with starting marking on fabric. Lower the foot, so that the buttonhole center line marked on the fabric aligns with the center of the buttonhole foot.
Adjust the stitch length dial in the " " to set stitch density.
Note:
Density varies according to the fabric.
Always test sew a buttonhole on the fabric you are using to sew the buttonhole.
Follow the 4-step sequence changing from one step to another with the stitch pattern selector dial. Take care not to sew too many stitches in stages 2 and 4. Use seam ripper and cut buttonhole open from both ends towards the middle.
Tips:
- Slightly reducing upper thread tension will produce better results.
- Use a backing for fine or stretchy fabrics.
- It is advisable to use heavy thread or cord for stretch or knit fabrics.
- The zig-zag should sew over the heavy thread or cord. (5)
1 2 3 4
3
2
1
0
5
24
3
4
2
1
Zippers and piping
Set the machine as illustrated.
Dial selector on " ".
Change to zipper foot.
Set stitch length control between "1" - "4" (according to thickness of fabric).
The zipper foot can be attached right or left, depending on which side of the foot you are going to sew. (1)
To sew past the zipper tab, lower the needle into the fabric, raise the presser foot and push the zipper tab behind the presser foot. Lower the foot and continue to sew.
It is also possible to sew a length of cord into a bias strip to form a "welt" or piping. (2)
4
3
2
1
0
25
1 2
Multi-stitch zig-zag
Sewing on lace and elastic, darning, mending, reinforcing edges.
Set the stitch pattern dial to " ".
Place patch in position. The stitch length can be shortened to produce very close stitches. (1)
When mending tears, it is advisable to use a piece of backing fabric to reinforce. The stitch density can be varied by adjusting the stitch length. First sew over the center and then overlap on both sides. Depending on the type of fabric and damage, sew between 3 and 5 rows. (2)
Bar tack
Set the stitch pattern dial to " " or " ".
Set the stitch length dial to "1" - "1.5".
This function is used to secure the tops of kick pleats, as well as pocket openings. First use a straight stitch across the top of the pocket or pleat. This seam should be approximately 1/4 to 1/2 of an inch long. Set stitch to zigzag and stitch over the straight stitch backstitch at the beginning and end of stitch to secure ends.
26
4
3
2
1
0
1 2
Free motion darning, stippling
* The darning foot is an optional accessory not included with your machine. (1)
Set the machine as illustrated.
Install the darning plate. (2)
Remove the presser foot clamp. (3)
Attach the darning foot to the presser foot holder. The lever (a) should be behind the needle clamp screw (b). Press the darning foot on firmly from behind with your index finger and tighten the screw (c). (4)
For darning, first sew around the edge of the hole (to secure the threads). (5)
First row: Always work from left to right. Turn work by 1/4 and oversew. A darning hoop is recommended for easier sewing and better results.
1
Note:
Free motion darning is accomplished without the sewing machine internal feed system. Movement of the fabric is controlled by the operator. It is necessary to coordinate sewing speed and movement of fabric.
Sew a straight or zigzag stitch following your design line. Using the optional darning foot will help guide you as you sew.
3
2
4
2
1
0
c
4
27
a b
5
Practical stitches
Set the machine as illustrated.
Turn the stitch length dial to suit the fabric and application.
Shell stitch (A)
For decorative edges.
Suitable for edges on sheer, fine and stretch fabrics. The larger stitch should go just over the edge of the fabric to create the shell effect.
Crescent stitch (B)
For a delicate edge finish along the edge of fabric.
4
3
2
1
0
28
A B
Applique and blindstitch applique
Position applique piece on background fabric.
Align needle so that it pierces background fabric along the outside edge if the applique. Lower presser foot.
If using a blindhem foot, align the lip of the blindhem foot guide so that it sits directly under the edge of the applique.
You may need to adjust the position of the guide to bring it closer or further from the edge of the applique, by using the thumbscrew located at the right of the foot.
Begin sewing following the edge of your applique. To pivot for curves or corners, leave needle down in fabric on outside edge of applique, lift foot and pivot.
3
2
1
0
29
Quilting functions
Stippling is free motion quilting where you hoop the fabric and guide it by hand, allowing you to stitch in any direction.
For template quilting transfer a design from a template (plastic stencil) to your fabric and then stitch following the outline.
Do not forget to lower the presser bar if you are sewing without a foot.
The above techniques are used to hold the layers of the quilt together.
For better control use a hoop, as well as a Darning and
Embroidery foot.
4
3
2
1
0
30
Mending
Machine Preparation:
- Pattern: Multi - stitch Zigzag
- Stitch width: Largest 4.5mm
- Stitch length: Fine (0.5 - 1.0)
Sewing Instructions:
Position a piece of fabric directly beneath the tear in your fabric.
Align the center of the foot with the center of the tear.
Stitchacross, backstitching at the start and at the end of the seam.
3
2
1
0
31
Stay-stitching
Machine Preparation:
- Pattern: Straight Stitch
- Stitch Width: Straight
- Stitch length: 1.5mm (fine)
Sewing Instructions:
Stay-stitching is used to reinforce curves such as armholes, seams in stretch fabrics and other areas to prevent stretching.
Stay stitch along the edge of the area 1/4 of an inch from the edge of the seam.
4
3
2
1
0
32
Blindstitch applique
Machine Preparation:
- Pattern: Blindhem
- Stitch Length: 2 - 3
- Foot: Standard Zigzag or optional Blindhem foot
Sewing Instructions:
Position applique piece on background fabric and secure it in place using fabric glue.
Align needle so that it pierces background fabric along the outside edge of the applique.
Lower presser foot. Using Blindhem stitch, proceed to sew, following the edge of your applique.
If using a Blindhem foot, align the lip of the blind hem foot guide so that it sits directly under the edge of the appliqué.
You may need to adjust the position of the guide to bring it closer or further from the edge of the applique, by using the thumbscrew located at the right of the foot.
To pivot for curves or corners, leave needle down in fabric on outside edge of applique, lift foot and pivot.
4
3
2
1
0
33
Traditional pintucks
Machine Preparation:
- Pattern: Straight
- Stitch Width: Straight
- Stitch Length: 2 - 3
Sewing Instructions:
To mark pintucks in your fabric, either pull a thread to mark the fold or mark with chalk or marking pencil.
Fold and press wrong sides together on pulled thread line or marked lines. Stitch 1/8 of an inch from fold line.
Repeat, sewing in the same direction for each tuck. Press flat.
4
3
2
1
0
34
Gathering
Machine Preparation:
- Pattern: Straight Stitch
- Stitch Width: Straight
- Stitch Length: Longest
Sewing Instructons:
Use this technique for gathering waistbands, sleeve caps etc. At
1/4 of an inch from the edge of the seam, begin by backstitching and then continue to sew the length required.
When seam is complete, raise the needle to it's highest, raise the presser foot and pull the upper and lower threads to the back of the foot.
Cut your thread ends leaving a minimum 6 inches of thread.
Repeat this procedure once again at 1/4 of an inch from your first row of stitching.
Once the two rows are completed, draw in your fabric the required amount by pulling on the bobbin thread. Secure thread ends.
4
3
2
0
35
Couching
Machine Preparation:
- Pattern: Zigzag
- Stitch width: Variable (Set according to width of cord)
- Stitch length: Variable
- Foot: Zigzag or optional Satin foot
Sewing Instructions:
Couching is simply the technique of zigzagging over a fine cord.
Use as a decorative touch on jackets and other sewing projects.
With a marking pencil, draw a design on your fabric.
Lay the cord under the center opening of your foot and zigzag over the cord so that the needle falls just to the right and left of the decorative cord.
As you sew, follow the lines of your design.
4
3
2
1
0
36
Trim attachment stitch function
- Set the stitch pattern dial to zigzag.
- Set the stitch length to "0".
- Sew 6 to 8 stitches to secure the trim in place.
- Then set needle to right needle position and then to sew the length of the trim.
- Set stitch pattern dial to straight stitch.
- Sew 2 to 3 stitches to tie off.
- This function is used to attach trim or ribbon to a sewing project.
4
2
1
0
37
Maintenance
Attention:
Disconnect the machine from the electrical supply by removing the plug from the main socket. When cleaning the machine, it must always be disconnected from the electrical supply.
Remove the needle plate:
Turn the handwheel until the needle is fully raised. Open the hinged front cover and unscrew the needle plate screws with the screw driver (1).
Cleaning the feed dogs:
Use the brush supplied to clean the whole area (2).
Cleaning and lubricating the hook:
Remove the bobbin case. Snap the two hook retaining arms (3) outwards. Remove the hook race cover (4) and the hook (5) and clean with a soft cloth. Lubricate at the point (6) (1-2 drops) with sewing machine oil. Turn the handwheel until the hook race (7) is in the left position. Replace the hook (5). Replace the hook race cover and snap back the two hook retaining arms. Insert the bobbin case and bobbin and replace the needle plate.
1
7
Important:
Fabric lint and threads must be removed regularly.
Your machine should be serviced at regular intervals at one of our service centers.
38
3
2
6
5
4
Trouble shooting guide
Problem
Upper thread breaks
Lower thread breaks
Cause
1.The machine is not threaded correctly.
2.The thread tension is too tight.
3.The thread is too thick for the needle.
4.The needle is not inserted correctly.
5.The thread is wound around the spool holder pin.
6.The needle is damaged.
1.The bobbin case is not inserted correctly.
2.The bobbin case is threaded wrong.
3.The lower thread tension is too tight.
Skipped stitches
Needle breaks
Loose stitches
Seams gather or pucker
Uneven stitches, uneven feed
The machine is noisy
The machine jams
1.The needle is not inserted correctly.
2.The needle is damaged.
3.The wrong size or type of needle has been used.
4.The foot is not attached correctly.
1.The needle is damaged.
2.The needle is not correctly inserted.
3.Wrong needle size for the fabric.
4.The wrong foot is attached.
1.The machine is not correctly threaded.
2.The bobbin case is not correctly threaded.
3.Needle/ fabric/ thread combination is wrong.
4.Thread tension wrong.
1.The needle is too thick for the fabric.
2.The stitch length is incorrectly adjusted.
3.The thread tension is too tight.
1.Poor quality thread.
2.The bobbin case is incorrectly threaded.
3.Fabric has been pulled.
1.The machine must be lubricated.
2.Lint or oil have collected on the hook or needle bar.
3.Poor quality oil has been used.
4.The needle is damaged.
Thread is caught in the hook.
Correction
1.Rethread the machine.
2.Reduce the thread tension. (lower number)
3.Select a larger needle.
4.Remove and reinsert the needle. (flat side towards the back)
5.Remove the reel and wind thread onto reel.
6.Replace the needle.
1.Remove and reinsert the bobbin case and pull on the thread.
The thread should pull easily.
2.Check both bobbin and bobbin case.
3.Loosen lower thread tension as described.
1.Remove and reinsert needle. (flat side towards the back)
2.Insert a new needle.
3.Choose a needle to suit the thread and fabric.
4.Check and attach correctly.
1.Insert a new needle
2.Insert the needle correctly. (flat side towards the back)
3.Choose a needle to suit the thread and fabric.
4.Select the correct foot.
1.Check the threading.
2.Thread the bobbin case as illustrated.
3.The needle size must suit the fabric and thread.
4.Correct the thread tension.
1.Select a finer needle.
2.Readjust the stitch length.
3.Loosen the thread tension.
1.Select a better quality thread.
2.Remove bobbin case, thread and insert correctly.
3.Do not pull on the fabric while sewing, let it be taken up by the machine.
1.Lubricate as described.
2.Clean the hook and feed dog as described.
3.Only use good quality sewing machine oil.
4.Replace the needle.
Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by hand and remove the thread.
Lubricate as described.
39
021V880105( ) Dec/05
SINGER 1507(8280C)
Stáhnout
Veřejný odkaz aktualizován
Veřejný odkaz na váš chat byl aktualizován. You may view and manage your chat links after registration here.
Veřejný odkaz na dokument
Reklama