Untitled - Datasheet.su

Untitled - Datasheet.su
equipment compatible with a one cycle transfer time
750 watts continuous AC output in inverter mode, 960 watts continuous AC output in AC mode
Double Boost inverter output supports momentary startup loads up to 200% of the continuous rating for up to 10 seconds
OverPower inverter output supports longer duration overloads to 150% for 1-60 minutes under ideal battery and temperature conditions. (For
best results, utilize OverPower usage for as short of a duration as possible, ensure battery bank and cabling is able to provide full nominal DC
voltage under load and allow inverter/charger to fully cool before and after OverPower usage.)
3 stage, 20 amp battery charger with adjustable settings for wet/gel battery types offers fast, reliable battery recharging
Protected hardwire bolt-down input lugs safely accept heavy gauge input wiring from attached battery bank
Two built-in NEMA 5-15R output receptacles pass 120V line power or inverter output through to connected equipment
Reliability enhanced large-transformer design with secure mounting flanges and protected DC wiring terminals
Moisture-resistant construction enables vehicular or marine operation in high humidity environments
3 position operating mode switch supports "AUTO" mode to enable automatic transfer between DC and AC modes, CHARGE-ONLY to maintain
a full battery charge when AC is present without auto transfer and SYSTEM OFF settings.
Set of six front panel LEDs display AC/DC operational modes, overload status, DC voltage level, shutdown status and system fault status
Set of 4 configuration dipswitches support wet/gel battery charging profiles, adjustable 135/145V high voltage auto transfer during overvoltages
and selectable 75/85/95/105V AC low voltage auto transfer during brownouts
Resettable 6A charger AC input breaker and resettable 8A AC output breaker and automatic 2 speed cooling fan protect the inverter from load
and temperature related failures
Grounding lug properly connects the inverter/charger system to earth ground or vehicle grounding system
Automatic overload and thermal shutoff safely turns off inverter as excessive loads or overheating conditions develop
Front panel remote control connector enables remote off/on switching (requires APSRM4 switch accessory). Optional APSRM4 accessory also
includes user configurable jacks to support inverter shutoff or startup as a vehicle ignition is engaged.
Specifications
SYSTEM OVERVIEW
Voltage compatibility
12V DC / 120V AC
Frequency
compatibility
60 Hz
OUTPUT
Output watts
750W (continuous) / 1500W (peak)
Output nominal
voltage
120V (AC) / 12V (DC Charger)
Output voltage
regulation
LINE POWER (AC): Maintains 120V nominal sine wave output from line power source. INVERTER POWER (AC):
Maintains PWM sine wave output voltage of 120 V AC (+/-5%).
Output frequency
regulation
60 Hz (+/- 0.3 Hz)
Outlet quantity / type
2 NEMA 5-15R
Overload protection
Includes 6A AC input breaker dedicated to the charging system and 8A output breaker for AC output loads
Continuous output
capacity (watts)
750
Peak output capacity
(watts)
1500
INPUT
Input connection type
DC INPUT: Set of 2 DC bolt-down terminals. AC INPUT: NEMA 5-15P input plug
Input cord length
DC INPUT: User supplies cabling. 6 gauge or larger (see manual). AC INPUT: attached 6 ft. AC line cord with plug
Recommended
electrical service
DC INPUT: Requires 12V DC input source capable of delivering 72A for the required duration (when used at full
continuous capacity - DC requirements increase during Over-Power and Double-Boost operation). AC INPUT: 15A
120V AC recommended
Maximum input
amps / watts
DC INPUT: Full continuous load - 72A at 12V DC. AC INPUT: 8 amps at 120VAC with full inverter and charger load
(4.2A max charger-only)
BATTERY
Expandable battery
runtime
Runtime is expandable with any number of user supplied wet or gel type batteries
DC system voltage
12V
Battery recharge rate
20A
LEDS ALARMS & SWITCHES
Front panel LEDs
Set of 6 LEDs offer continuous status information on load percentage (6 levels reported) and battery charge level (7
levels reported). See manual for sequences.
Switches
3 position on/off/remote switch enables simple on/off power control plus "auto/remote" setting that enables distant on/off
control of the inverter system when used in conjunction with optional APSRM4 accessory when used in inverter mode.
In AC uninterrupt
SURGE / NOISE SUPPRESSION
AC surge
suppression
450 joules
PHYSICAL
Shipping weight (lbs)
18.6
Shipping weight (kg)
8.4
Shipping
Dimensions (HWD/in)
12.5 x 11 x 10.75
Shipping
Dimensions
(HWD/cm)
31.8 x 27.9 x 27.3
Unit weight (lbs)
17
Unit weight (kg)
7.7
Unit Dimensions
(HWD/in)
7 x 8.75 x 9
Unit Dimensions
(HWD/cm)
17.8 x 22.3 x 22.9
Material of
construction
Polycarbonate
Form factors
supported
Mounting slots enable permanent placement of inverter on any horizontal surface (see manual for additional mounting
information)
Cooling method
Multi-speed fan
Receptacle Color
BLACK
ENVIRONMENTAL
Relative Humidity
0-95% non-condensing
LINE / BATTERY TRANSFER
Transfer time from
line power to battery
mode
16.6 milliseconds (typical - compatible with many computers, servers and networking equipment - verify transfer time
compatibility of loads for UPS applications)
Low voltage transfer
to battery power
In AC "auto" mode, inverter/charger switches to battery mode as line voltage drops to 75V (user adjustable to 85, 95,
105V - see manual)
High voltage transfer
to battery power
In AC "auto" mode, inverter/charger switches to battery mode as line voltage increases to 135V (user adjustable to 145
- see manual)
WARRANTY
Product warranty
1 year (Outside the U.S. and Canada, call for warranty information)
©2008 Tripp Lite. All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement