To change the setting from baseboard to fan IMPORTANT

To change the setting from baseboard to fan IMPORTANT
IMPORTANT INSTRUCTIONS
FOR FAN-FORCED HEATER USE
Please note: The TH106 comes factory set in baseboard
mode (even though the Honeywell Owner’s Guide
incorrectly reflects a factory setting of fan mode). If using
the TH106 to control a fan-forced heater, you must change
the setting for switch 3.
To change the setting from baseboard to fan
heater: The configuration switches are on the back of the
thermostat cover. Change factory setting for switch 3 to the
right, or ‘ON’ position (5 minute cycle length). See page 2 of
your thermostat Owner’s Guide, Section 3 Configuration,
for more detailed information on switch settings.
2
ON
1
Switch 3 Setting
LEFT for
RIGHT for
Baseboards Fan Heaters
configuration
switches
4
DIP
3
switch
3
15 second
cycles
Baseboard
5 minute
cycles Fan
Heater
Instructions are also available on our website at cadetheat.com
Rev 07/15
720018
400-106-023-F_69-2202-04 (TH106-03 Honeywell TL6160A1004 Cadet 08160) ENG.fm Page 1 Tuesday, April 6, 2010 2:40 PM
08160
TH106
TL6160
NOTE: Always keep the thermostat's vents clean and unobstructed.
Temperature
preset buttons
n
Indicates that the
temperature setpoint
is displayed
Indicates that the
settings are locked
Time and day
Set the day
Temperature
Set the time
Indicates the current
mode of operation
Program the schedule
Temperature
preset icon
Skip a period
Indicates that the
thermostat is configured
for a fan-forced heater
Select the mode
of operation
Indicates the
heating power
Temperature
adjustment
buttons
o
Indicates the current
period (appears in
automatic mode only)
Connect the thermostat wires to the line wires and to the load
wires using solderless connectors for copper wires.
Indicates that the thermostat is without power *
* LP appears only for the first two minutes when the thermostat is without power. This
can occur during a power outage or when the thermal protection device inside the baseboard heater is opened.
n
Description
1.
2-wire installation
This programmable thermostat can be used to control an electric
heating system such as an electric baseboard heater, a radiant ceiling, a radiant floor, a convector or a fan-forced heater.
The thermostat cannot be used with:
•
•
•
•
a resistive load over 16.7 A
a resistive load under 2 A
a system driven by a contactor or relay (inductive load)
a central heating system
4-wire installation
SUPPLIED PARTS:
•
One (1) thermostat
•
Two (2) 6-32 screws
•
Two (2) solderless connectors
o
Installation
2.
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK. THE INSTALLATION MUST BE PERFORMED BY AN ELECTRICIAN.
All cables and connections must conform to the local electrical
code.
Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.
Install the thermostat onto an electrical box.
Install the thermostat about 5 feet high, on an inside wall facing
the heater.
Avoid locations where there are air drafts (such as the top of a
staircase or an air outlet), dead air spots (such as behind a
door), or direct sunlight.
Do not install the thermostat on a wall that conceals chimney or
stove pipes.
The thermostat wires are not polarized; either wire can be connected to the load or to the power supply.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
p
Push any excess wire back into the electrical box.
NOTE: If necessary, before re-installing the front component, configure the thermostat (see section 3).
q
Return power to heating system.
69-2202-04
2010-04-06
1/4
400-106-023-F_69-2202-04 (TH106-03 Honeywell TL6160A1004 Cadet 08160) ENG.fm Page 2 Tuesday, April 6, 2010 2:40 PM
p
3.
Configuration
Setpoint
The thermostat normally displays the actual temperature. To view the
setpoint, press the
or button briefly. The setpoint will appear for
the next 5 seconds.
To change the setpoint, press the
or
button until the desired
temperature is displayed. To scroll faster, hold the button.
Using a preset temperature
The thermostat has 3 preset temperatures:
The configuration switches are on the back of
the thermostat. The factory settings are indicated by the gray cells in the following table.
SW1 Early Start a
Off
On
SW2 Display format
°C / 24-hour
°F / 12-hour
SW3 Cycle length b
15 seconds /
Baseboard heater
5 minutes /
Fan-forced heater
SW4 Keypad lock c
Off
On
q
n
o
p
q
4.
Press the Hour button to set the hour.
Press the Min button to set the minutes.
Press the Day button to set the day.
Press the Mode button to end.
Daylight Savings Time
The thermostat can automatically re-adjust its clock at Daylight Savings Time changeover. When this function is enabled (On), the thermostat switches to Daylight Savings Time on the second Sunday of
March and to normal time on the first Sunday of November.
NOTE: The function is disabled (default setting) when the clock loses
its setting.
n
Press the Day button (3 seconds) until DLS appears
on the screen.
o
Press either of the
buttons to toggle between On
(enabled) and Off (disabled).
p
Press the Day button briefly. The year setting is displayed.
Press either of the
buttons to set the current year.
q
r
s
Press the Day button briefly. The month setting is displayed.
Press either of the
buttons to set the current
month.
t
Press the Day button briefly. The date setting is displayed.
u
v
Press either of the
Comfort temperature
Economy temperature
Vacation temperature
Icon
a. Early Start can be used in Automatic mode only. When this function is enabled, the thermostat calculates the optimal time to start
heating in order to obtain the desired temperature by the set time.
The thermostat re-assesses the start time daily based on the previous day’s performance.
b. You must select 5 minutes if you have a fan-forced heater. The
word FAN is displayed when this setting is selected. Select
15 seconds for better temperature control in most other cases.
c. The settings are locked. The temperature adjustment buttons only
allow you to view the temperature setpoint.
Clock and Day Setting
r
5.
Temperature Setting
Intended use
Factory setting
Comfort (when at home)
70°F (21°C)
Economy (when asleep or away from home)
Vacation (during prolonged absence)
•
62°F (16.5°C)
50°F (10°C)
To use the Comfort or Economy temperature, press the
or
button respectively. The corresponding icon will be displayed.
•
To use the Vacation temperature, press both
and buttons
simultaneously. The icon will be displayed.
Storing a preset temperature
To store the Comfort or Economy temperature:
Set the desired temperature using the or button. Press and
hold the appropriate button ( or ) for approximately 3 seconds until the corresponding icon is displayed.
To store the Vacation temperature:
Set the desired temperature using the or button. Press and
hold both
and buttons simultaneously for approximately 3
seconds until the icon is displayed.
s
6.
Modes of Operation
Automatic - The temperature is set according to the programmed
schedule. To place the thermostat in this mode, press the Mode button until
is displayed. The icons of the current period and preset
temperature are also displayed.
Temporary Bypass: If you modify the setpoint (by pressing the
, ,
or button) when the thermostat is in automatic mode,
the new setpoint will be used until the end of the current period.
When the next period starts, the temperature set for that period
becomes the new setpoint. To cancel the bypass, press the
Mode button.
Manual - The programmed schedule is not used. The temperature
must be set manually. To place the thermostat in this mode:
n
o
Press the Mode button until
Set the temperature using the
is displayed.
,
,
or
button.
buttons to set the current date.
Press the Mode button to end.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
69-2202-04
2010-04-06
2/4
400-106-023-F_69-2202-04 (TH106-03 Honeywell TL6160A1004 Cadet 08160) ENG.fm Page 3 Tuesday, April 6, 2010 2:40 PM
t
7.
Schedule
v
The schedule consists of 4 periods per day which represents a typical weekday. You can program the thermostat to skip the periods that
do not apply to your situation. For example, you can skip periods 2
and 3 for the weekend.
Period
Description
PROBLEM
Thermostat is hot.
LO is displayed.
The measured temperature is below the
display range. Heating is activated.
HI is displayed.
The measured temperature is above the
display range.
Wrong temperature is
displayed.
The thermostat is exposed to air draft.
Eliminate the draft.
The sticker on the thermostat’s screen has
not been removed.
Wrong time is displayed.
The thermostat was without power for
more than 4 hours.
Leave
Return
Sleep
The Comfort ( ) temperature is used in periods 1 and 3 and the
Economy ( ) temperature is used in periods 2 and 4. For example,
when the period changes from 1 to 2, the setpoint automatically
changes from Comfort setting ( ) to Economy setting ( ).
You can have a different program for each day of the week; i.e., each
period can start at different time for each day of the week. The
thermostat has been programmed with the following schedule.
Period
Setting
TU
WE
TH
FR
SA
SU
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
--:--
--:--
6:00
PM
6:00
PM
6:00
PM
6:00
PM
6:00
PM
--:--
--:--
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
Press Pgm to access the programming mode. Period 1 is
selected.
o
Press Day to select the day to program (hold for 3 seconds to
select the entire week).
p
Press Hour and Min to set the start time of the selected period,
or press Clear if you want to skip the period (--:-- is displayed).
Press Pgm to select another period, or press Day to select
another day. Then repeat step 3.
Press Mode to exit the programming mode.
NOTE: If no button is pressed for 60 seconds, the thermostat will
automatically exit the programming mode.
u
Power Outage
Display looks faded
when heating is activated
The heating system is less than the
required minimum load. This thermostat
cannot be used below that rating.
The settings cannot be
changed.
The settings are locked (see section 3).
w
n
r
Temperature does not
Check that the thermostat is in Automatic
change according to the mode. Check the schedule and clock setprogrammed schedule. tings.
The thermal circuit breaker in the heater is
LP appears on the
opened. This can happen if the heater is
screen or the screen is
obstructed by furniture or curtain and has
blank despite there is no
overheated, or if the thermal circuit breaker
power outage.
is defective.
MO
To modify the schedule:
q
SOLUTIONS
This condition is normal. Under normal
operation, the thermostat housing can
reach a temperature between 95°F (35°C)
and 104°F (40°C).
Setting
Wake
9.
Troubleshooting
8.
10.
Technical Specifications
Power: 120/240 VAC, 60 Hz
Minimum load: 2 A (resistive only)
250 W @ 120 VAC
500 W @ 240 VAC
Maximum load: 16.7 A (resistive only)
2000 W @ 120 VAC
4000 W @ 240 VAC
Display range: 32°F to 140°F (0°C to 60°C)
Display resolution: 1°F (0.5°C)
Setpoint range: 40°F to 86°F (5°C to 30°C)
Setpoint interval: 1°F (0.5°C)
Storage: -4°F to 120°F (-20°C to 50°C)
During a power outage, LP (Low Power) appears for the first minute.
Then the screen becomes blank. The settings are stored in memory.
However, if the power failure exceeds 4 hours, the thermostat’s clock
must be re-adjusted and, if you are using the automatic Daylight Savings Time changeover function, it must be re-enabled. When power
returns, the thermostat will return to the mode of operation active
prior to the power failure.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
69-2202-04
2010-04-06
3/4
400-106-023-F_69-2202-04 (TH106-03 Honeywell TL6160A1004 Cadet 08160) ENG.fm Page 4 Tuesday, April 6, 2010 2:40 PM
;
Warranty
11.
Honeywell warrants this product, excluding battery, to be free from
defects in the workmanship or materials, under normal use and
service, for a period of three (3) years from the date of purchase by
the consumer. If at any time during the warranty period the product is
determined to be defective or malfunctions, Honeywell shall repair or
replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to
the place from which you purchased it, or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer
Care will make the determination whether the product should be
returned to the following address: Honeywell Return Goods,
Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN
55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This
warranty shall not apply if it is shown by Honeywell that the defect or
malfunction was caused by damage which occurred while the
product was in the possession of a consumer.
Honeywell's sole responsibility shall be to repair or replace the
product within the terms stated above. HONEYWELL SHALL NOT
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH
OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER
FAILURE OF THIS PRODUCT. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so this
limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY
HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF
ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR
DURATION OF THIS WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.
If you have any questions concerning this warranty, please write
Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN
55422 or call 1-800-468-1502. In Canada, write Retail Products
ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive,
Scarborough, Ontario M1V 4Z9.
Customer Assistance
12.
If you have any questions about the operation of your thermostat,
please go to http://yourhome.honeywell.com, or call Honeywell
Customer Care toll-free at 1-800-468-1502.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
69-2202-04
2010-04-06
4/4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement