English - Toshiba Canada

English - Toshiba Canada
English
Declaration of Conformity
Manufacturer: Toshiba Corporation
1-1, Shibaura 1-Chrome, Minato-ku, Tokyo, Japan
We declare under our sole responsibility that the TDP-MT100 projector conform to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
October, 2002
Australian Certification C-tick mark
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of International
Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation.
FCC Warning
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, c-UL, TÜV, NOM, IRAM, GOST, S-JQA
If you are experienced in setting up projection systems, use the Quick Setup
card that was included. For complete details on connecting and operating
the projector, refer to this User’s Guide.
Table of Contents
Introduction
Positioning the projector
Connecting a video device
Video connections
Video device connections
Composite video connection
S-video connection
Component video connection
VGA connection
Displaying video
Adjusting the image
Connecting a computer source
Required computer connections
Optional computer connections
Displaying a computer source image
Adjusting the image
Using the projector with Windows 98 for the first time
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing video images
Customizing the projector
Optimizing computer images
Presentation features
Using the menus
Picture menu
Settings menu
Maintenance
Cleaning the Lens
Replacing the Projection Lamp
Cleaning the Lamp Housing Screens
Appendix
Specifications
Accessories
For assistance with this projector
Projected image size
Red LED Behavior and Projector Errors
4
5
6
7
8
8
8
9
9
10
10
12
12
12
13
14
15
16
16
24
25
25
26
26
27
27
28
29
32
35
35
35
37
38
38
38
39
39
40
Important Operating Considerations
Do not place the projector on a tablecloth or other soft coverings that may
block the front or back vents. Do not use a non-approved ceiling mount. In
the unlikely event of the bulb rupturing, thoroughly clean the area in front
of the projector and discard any edible items that may have been placed in
that area.
2 ft (
3
.6m)
Do not place objects in
this area in front
of the projector
Introduction
speaker
keypad
Your new digital projector is easy to connect, use, and maintain. The TDPMT100 is compatible with a wide variety of video devices and computers,
including:
•
Most standard VCRs, DVD players (progressive and interlaced), HDTV
sources (1080i, 1035i, and 720P HDTV formats), TV and satellite tuners,
camcorders, video games, and laser disc players.
•
IBM-compatible computers, including laptops, up to 1024x768 resolution.
•
Apple® Macintosh® and PowerBook® computers up to 1024x768 resolution.
power cord
connector
power switch
remote control
receiver (IR)
adjustable foot release
focus (thin ring)
zoom (thick ring)
The projector has native SVGA 800x600 resolution and comes with the following standard accessories.
lamp
housing
door
projector
connector
panel
documentation
ide
’s Gu
User
security lock
lens cap
power cord*
component
to S-video
adapter
video
cable
audio
cable
adjustable foot
computer
cable
remote control
audio
adapter
*country-dependent
monitor
4
computer S-video video audio
USB
Positioning the projector
•
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. The top illustration to the right shows three projected image sizes. For more information about image sizes at different distances, see “Projected image
size” on page 39.
•
The image exits the projector at a given angle. The image offset is
112.2% when the projector is in 4:3 mode (default mode). This means
that if you have an image 10’ high, the bottom of the image will be 1.22’
above the center of the lens.
•
This image offset is 124.7% when the projector is in 16:9 mode. This
means that if you have an image 10’ high, the bottom of the image will
be 2.47’ above the center of the lens.
•
See “Connecting a video device” on page 6 for additional information
on 16:9 and 4:3 modes.
f t.
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 32. Toshiba recommends using an authorized Toshiba ceiling mount. The Ceiling Mount
Kit is sold separately.
.5
•
ft.
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
f t.
•
5
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.49m) from the projection screen.
3
3.
•
12
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guidelines:
4.8 ft.
10 ft high
image
bottom of image
1.22 ft above lens
5
19 ft.
7.5 ft.
Projection angle in 4:3 mode (default)
lens center
Connecting a video device
You can connect VCRs, DVD players, camcorders, digital cameras, video
games, HDTV receivers, and TV tuners to the projector. There is also an
audio input. You can connect the audio directly to the projector to get sound
from the onboard speaker, or you can connect it to your stereo’s receiver to
get sound from your own speakers.
Before connecting your projector, you should decide which aspect ratio you
want to use. Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3, which is the default for this projector. HDTV and
most DVDs are 16:9. If you’re projecting onto a screen, the size/shape of the
screen may answer this question for you. If you are projecting onto a blank
wall, you don’t have the screen size restriction. What you plan to project
will also help you choose between 4:3 and 16:9. Most regular TV shows are
4:3, while most movies are 16:9.
If you select 4:3 and play TV, the image will fill the screen. If you select 16:9
and play HDTV, the image will fill the screen. However, if you select 4:3 and
play a 16:9 DVD, the image may be compressed horizontally or have black
bars along the top and bottom. If you select 16:9 and play regular TV, the
image may be stretched horizontally or have black bars along the sides. You
can make this selection later using the onscreen menus page 29), but for
now you just need to know which format you’ll use most often.
16:9 image in a 4:3 space
9
4:3 image in a
16:9 space
black bars
4
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered
a tuner.
6
16
black bars
3
black bars
black bars
Here is a list of possible input signals and the connectors they should be
connected to on the projector:
Video connections
The next step is to figure out what type of connectors/output the equipment you want to connect has. If there is more than one output, select the
one with the highest quality. Component video has the best quality, followed by S-video, then composite video.
If you are connecting the projector to HDTV, the projector’s computer connector should be used.
Keep in mind that HDTV and progressive sources can only be handled
through the projector’s VGA connector. The Component to S-video adapter
does not function with progressive sources. With progressive sources, the
Component video connector requires Breakout cables purchased from a
third-party.
NOTE: S-video cables are not included with the TDP-MT100 projector.
7
Input Signal
Connector
Connector Label on
Projector
Standard Broadcast
TV (not HDTV), via
cable, digital cable,
satellite TV, DVD,
VCR, DirectTV
Composite video
Video In
S-video
S-video
Component Video
S-video (via the
Component to
S-video adapter)
HDTV, Progressive
DVD, Progressive
Video Game
VGA
Computer In
Component video
Component Video
requires third-party
Breakout cable
Video Camera,
Video Game
Composite video
Video In
S-video
S-video
Video device connections
Composite video connection
Plug the included video cable’s yellow connector into the video-out connector on your video device. Plug the other yellow connector into the yellow
Video In connector on the projector. Plug the included audio adapter’s
white connector into the left audio out connector on your video device; plug
the audio adapter’s red connector into the right audio out connector on the
video device. Plug the included audio cable into the black connector on the
audio adapter. Plug the other end of the audio cable into the blue Audio In
connector on the projector.
connect video cable and audio cable (via
the audio adapter)
Keep in mind that video output from composite connections are not as high
quality as S-video or component.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable (sold separately) into the S-video connector on your video
device and into the S-video connector on the projector. Use the audio cable
and the audio adapter as described above.
connect S-video and audio cable (via
audio adapter)
Keep in mind that S-video delivers higher quality video output than composite, but not as high quality video output as component.
8
Component video connection
connect component cables via component
to S-video adapter and audio cables via
audio adapter
If your video device has component connectors, use the component to
S-video adapter. Plug the component cable into the video device. Plug the
other end of the component cable into the adapter and plug the adapter into
the projector’s S-video connector. Use the audio adapter as described on the
previous page.
Component connection offer the highest quality video output.
VGA connection
connect VGA cable and
audio cable via audio
adapter
If your video device has a 15-pin VGA output, plug one end of the included
computer cable to the VGA connector on your video source. This connector
may be labeled “To Monitor” on the video source. Plug the other end of the
cable into the Computer In connector on the projector.
Use the audio adapter as described on the previous page.
Connect the power cord to the Power connector on the side of the projector
and to your electrical outlet.
connect power cable
NOTE: Always use the power cord that shipped with the projector.
9
Displaying video
remove lens cap
Remove the lens cap.
toggle Power switch
Toggle the Power switch on the side of the projector to the On position.
The LED flashes green and the fans start to run. When the lamp comes on,
the start-up screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 17.
Plug in and turn on your video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.
? No start up screen? Get help on page 23.
Adjusting the image
adjust height
Adjust the height of the projector by pressing the release button to extend
the foot.
Rotate the leveling foot at the rear of the projector, if necessary.
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
See page 39 for a table listing screen sizes and distances to the screen.
10
release button
rotate
leveling
foot
Adjust the zoom and focus.
adjust zoom and focus
focus
(thin ring)
If the image is not square, adjust the keystone using the buttons on the keypad. Press the top Keystone button to reduce the upper part of the image,
and press the bottom Keystone button to reduce the lower part.
adjust keystone
adjust volume
Adjust the volume on the keypad.
Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture
menu. See page 29 for help with the menus and these adjustments.
adjust Picture menu options
including Aspect Ratio
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 6.
11
zoom
(thick ring)
Connecting a computer source
connect computer cable
Required computer connections
Connect one end of the computer cable (see page 6 for connecting video
devices) to the dark blue Computer In connector on the projector. Connect
the other end to the video port on your computer. If you are using a desktop
computer, you will need to disconnect the monitor cable from the computer’s video port first.
Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet.
connect power cable
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To have sound with your presentation, connect the audio cable to your computer and to the Audio In connector on the projector.
connect audio cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
connect monitor cable
12
Displaying a computer source image
remove lens cap
Remove the lens cap.
Toggle the Power switch on the side of the projector to the On position.
toggle Power switch
The LED flashes green and the fans start to run. When the lamp comes on,
the start up screen displays and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 17.
Turn on your computer.
turn on computer
The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.
If your computer has Windows 98 as its operating system, see “Using the
projector with Windows 98 for the first time” on page 15 regarding the
driver setup process.
Make sure your laptop’s external video port is active.
activate laptop’s external port
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your laptop’s documentation
to learn your laptop’s key combination.
? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 18.
13
Adjusting the image
adjust height
Adjust the height of the projector, if necessary, by pressing the release button to extend the foot.
rotate
leveling
foot
Rotate the leveling foot located at the rear of the projector, if necessary.
elevator
foot
Avoid placing your hands in near the hot exhaust vent in front of the projector.
release button
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
See page 39 for a table listing screen sizes and distances.
adjust zoom or focus
Adjust the zoom or focus.
focus
(thin ring)
If the image is not square, adjust the keystone using the buttons on the keypad.
adjust keystone
Press the top Keystone button to reduce the upper part of the image, and
press the bottom Keystone button to reduce the lower part.
Adjust the Contrast or Brightness in the Picture menu.
adjust Picture menu
See page 29 for help with these menu adjustments.
14
zoom
(thick ring)
Using the projector with Windows 98 for the first
time
a
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000 or Windows ME, skip these steps and go
to “Adjusting the image” on page 14.
b
a Click Next to begin searching for the driver.
b Make sure “Search for the best driver” is selected, then click Next.
c
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
d
d When Windows finds the driver, you are ready to install it. Click Next.
15
Shutting down the projector
Troubleshooting your setup
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
The LED on top of the projector indicates the state of the projector and can
help you troubleshoot.
Screen Save
Table 1: LED behavior and meaning
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save feature in the Settings>System menu. See
page 32.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 32.
LED color/behavior
Meaning
solid green
The power switch has been toggled on
and the software has initialized. The projector has been powered off via the
remote.
blinking green
The power switch has been toggled on
and the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
blinking red
A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 22).Turn off the projector and wait
one minute, then turn the projector on
again. If the projector has been working
for 3,000 hours or more (page 35),
replace the lamp and reset the lamp timer.
Contact your Toshiba dealer if the problem persists.
Turning off the projector
You can turn the projector off simply by toggling the power switch to the off
position.
You can also press the remote’s Power button to place the projector in the
Off state while it is running. When the Power button is pressed twice (once
to start the power-down process and a second time to verify that you want
to power the projector off), the lamp turns off and the LED blinks green for
one (1) minute while the fans continue to run to cool the lamp. While the
LED is blinking green, the projector does not accept any keypad and remote
control input.
see page 40 for more information
When the lamp has cooled, the LED lights solid green and the fans slow
down to minimal speed. To turn off the projector, toggle the power switch to
the off position.
solid red
NOTE: Once the projector has been toggled off, you must wait for one (1)
minute before turning the projector on again. This allows the lamp to properly cool. However, if the remote was used to power the projector to the Off
state you do not need to wait one minute to turn it on again.
An unidentifiable error: please contact
your Toshiba dealer.
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
16
Problem
Solution
Result
no start up screen
plug power cord in projector’s left side
remove lens cap
toggle power switch
correct image
Corr
ec
Imag t
e
toggle power switch
on side
press the Computer button
activate laptop’s external port
only start up screen appears
A
Correc
t
Image
computer image projected
A
restart laptop
17
A
Problem
Solution
Result
no computer image, just the words “Signal out of
range”
press the Auto Image button on keypad
computer image projected
A
A
Signa
l
rang out of
e
adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)
you may also need to set a different
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped”
18
A
Problem
Solution
Result
image fuzzy or cropped
set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab)
select 800x600
image clear and not cropped
AA
A
A
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
image not centered on screen
move projector, adjust zoom, adjust height
adjust horizontal or
vertical position in
Picture>Advanced
menu
19
correct image
Problem
Solution
Result
image not square
adjust Keystone on keypad
square image
image not sharp
adjust Sharpness (video sources only) in the
Picture>Advanced menu
correct image
AB
AB
image does not fit 4:3 or 16:9 screen
change aspect ratio to 4:3 or 16:9 in
Picture>Aspect ratio menu
20
correct image
Problem
Solution
Result
image upside down
turn off ceiling in Settings>System menu
correct image
AB
image reversed left to right
AB
turn off rear in Settings>System menu
correct image
A
projected colors don’t match source
AB
adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
correct image
COLOR
21
Problem
Solution
Result
lamp won’t turn on, LED blinking red
make sure vents aren’t blocked, turn off the
projector and allow it to cool for a minute
lamp turns on
LED
“Change lamp” message appears at startup or lamp
won’t turn on and LED blinking red
LED
Corr
ec
Imag t
e
if lamp hours > 3,000, lamp must be
replaced (see page 35)
check lamp hours
Main>About
Corr
ec
Imag t
e
replace lamp
22
lamp turns on
Problem
Solution
Result
no video image
press the Auto Image button on keypad
video image projected
A
Still need assistance?
If you need assistance, please contact
your authorized Toshiba dealer.
23
Troubleshooting the remote
Using the remote control
The remote uses two (2) provided AAA batteries. They are easily installed
by sliding the cover off the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
The remote also has:
•
backlight button to light the remote’s buttons in the dark
•
Brightness and Contrast buttons to adjust the image
•
Blank button to display a blank screen instead of the current image (to
change the color of the screen, see page 33)
•
Source buttons to switch among sources (to assign a particular source
to a source button, see page 32) and a source toggle
•
Resize button to change the Aspect Ratio (see page 29)
•
Auto Image button to resynch the projector to the source
•
Preset button to restore stored settings (see page 30)
•
Overscan button to remove noise in a standard definition television
(SDTV) image (page 31)
•
Make sure you’re pointing the remote at the projector or the screen, not
at the video device or the computer, and are within the remote range of
30 feet (9.14m).
backlight button
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 28 for more info on the menus.
Power button to turn the projector on and off (see page 16 for shutdown info)
Make sure the batteries are installed in the proper orientation and are
not dead.
navigation buttons
To operate, point the remote at the projection screen or at the projector (not
at the video device or computer). The range of optimum operation is 0 to
30 feet (9.14m).
•
•
24
Using the audio
connect audio cable
To use the projector’s speaker, connect your source to the Audio In connector on the projector. See page 8 regarding using the audio adapter.
To adjust the volume, press the Volume buttons on the keypad.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the audio cable is connected.
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad.
•
Make sure the correct source is active.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
adjust volume
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Menu–opens the on-screen menus (page 28).
Select–confirms choices made in the menus (page 28).
Up/Down arrows–navigates to and adjusts settings in the menus (page 28).
Auto Image–resets the projector to the source.
menu navigation
buttons
Presets–cycles through the available preset settings (page 30).
Keystone–adjusts squareness of the image (page 14).
Volume–adjusts sound (page 25).
Video and Computer–changes the active source.
25
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 28.
You can customize the projector for your specific setup and needs. See
page 32 to page 34 for details on these features.
•
For rear projection, turn rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu (page 29).
•
For ceiling mounted projection, turn ceiling mode on in the Settings>System menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
•
Specify which source the projector checks first for active video during
power-up.
•
Select a Sharpness setting (page 31).
•
Turn the projector’s display messages on and off.
•
Use the Color Control to adjust the color gain (page 31).
•
Turn on power saving features.
•
Adjust the Color Temperature. Select a listed warmth value (page 31).
•
Specify blank screen colors and start up logos.
•
Turn on Overscan to remove noise on the edges of the image for SDTV.
•
Specify the language viewed on the menus.
•
Save settings for the active source as a preset.
26
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 28.
Several features are provided to make giving presentation easier. Here is an
overview, details are found in the menu section.
•
The Blank button on the remote allows you to display a blank screen
instead of the active source. You can determine the color of this screen
(page 33).
Change the Aspect Ratio. Choose the option that best fits your input
source (page 29).
•
The Startup Logo option lets you change the default start up screen to a
blank or default screen (page 33).
•
Adjust the Color Temperature in the Advanced menu (page 31).
•
•
Adjust the phase, Tracking, or Horizontal or Vertical position in the
Advanced menu (page 31).
Two options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 32).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 30).
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu
(page 29).
•
27
Using the menus
keypad navigation
buttons
Main menu
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Exit, then press Select to go to the
previous menu; press the Menu button at any time to close the menus.
dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Settings
menu
Picture
menu
Dots appears before the menu name. The number of dots indicate menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
Certain menu items may be not visible or may be grayed depending upon a
particular source being connected. For example, Sharpness is only available
for video sources and is not visible when a computer source is active. Menu
options are grayed out only if the source if selected but no signal is present.
For example, if the projector is set to a video source but the source, such as a
DVD player, is turned off video menu options are grayed out.
About menu
28
Picture menu
Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
increasing keystone
decreasing keystone
Brightness: changes the intensity of the image.
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is
4:3.
Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 6.
Aspect ratio
29
Presets: Presets are provided that optimize the projector for displaying
computer presentations, photographs, film images, and video images. Film
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event. You can use the preset as a starting point, then further customize the settings for each source. The settings you customize are saved in
the preset for each source. To restore the factory default settings, choose Factory Reset in the Settings>Service menu (page 34).
Presets
Save
User
Settings
There is also a user-definable preset. To set a preset for the current source,
adjust the image, select Save User in the Presets menu, then select Yes. You
can recall these settings in the future by selecting the User 1 preset.
30
Advanced menu
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Advanced menu
Sharpness
Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.
Color Temperature
Color Control: allows you to individually adjust the gain for the red, green,
and blue colors.
Color Control
Video Standard: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Overscan: (video sources only) removes noise around the video image.
The following four (4) options are for computer sources only.
Video Standard
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
31
Settings menu
Settings menu
Audio: allows adjustments to Volume of the internal speaker. Adjustments
can also be made from the projector’s keypad.
Audio
Sources: allows you to assign a particular input (Computer 1, Video 1, and
Video 2) to a specific source key on the remote and enables or disables Autosource. When Autosource is not checked, the projector defaults to the lastused source. If no source is found, a blank screen displays. When Autosource is checked, the projector checks the last-used source first at power
up. If no signal is present, the projector checks the sources in order until a
source is found or until power down.
Sources
Power-up
Source
Power-up Source determines which source the projector checks first for
active video during power-up. When the Autosource feature is On, the projector automatically finds the active source, checking the Power-up Source
first. The options are Computer 1 for a computer source, and Video 1 (for Svideo connections), and Video 2 (for composite video connections) for video
sources. When this feature is Off, the projector defaults to the source
selected in Power-up Source.
System menu
System: Rear reverses the image so you can project from behind a translucent screen. Ceiling turns the image upside down for ceiling-mounted projection. Display Messages displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen. NND prevents your notebook
computer from going into Screen Save mode. Power Save automatically
turns the lamp off after no signals are detected for 20 minutes. After an
additional 10 minutes with no signal, the projector powers down and can be
toggled off. If an active signal is received before the projector powers down,
the image will be displayed. When Power Save is enabled, Screen Save is
disabled. Screen Save automatically blanks the screen with a black color
after no signals are detected for a preset number of minutes. The image
returns when an active source is detected or a remote or keypad button is
pressed.
Screen Save
32
Startup Logo: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Startup Logo
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Blank Screen
Note: An Effect Key submenu is displayed under the Settings menu. This
feature, however, is not enabled for this model.
33
Language: allows you to select a language for the onscreen display.
Language menu
Service: To use these features, highlight them and press Select.
Service menu
Factory Reset: restores all settings to their default.
Lamp Reset: resets the lamp hours used counter in the About menu to
zero. Do this only after changing the lamp.
Service Code: only used by authorized service personnel.
About: provides information about the projector and the active source.
About menu
34
Maintenance
Cleaning the Lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Replacing the Projection Lamp
The lamp hours used timer in the About menu counts the number of hours
the lamp has been in use. After 2,980 hours, the message “Change lamp”
appears on the screen at startup. If the maximum lamp time of 3,000 hours
is exceeded, the lamp will not light. In this case, after replacing the lamp
you must reset the lamp hours by simultaneously pressing both Volume
buttons on the keypad and holding them for 10 seconds.
Lamp hours used
wait 60 minutes
NOTE: You can order new lamp housings from your dealer. See “NOTE:
Use only approved accessories.” on page 39 for information. Use only a
replacement lamp (see “Optional Accessories” on page 39 for the part number) with the same type and rating as the original lamp.
1 Turn off the projector and unplug the power cord.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Turn the projector on its side so that the lamp door is facing you. Using a
flat-blade screwdriver, gently pry the lamp door from the projector by
placing the screwdriver blade into the space between the top of the lamp
door and the projector.
lamp door
35
4 Loosen the two captive screws that attach the lamp housing to the pro-
lamp
connector
jector.
5 Detach the lamp connector from the projector by depressing the locking
lamp cable
tab on the connector and lightly pulling it free.
WARNING:
To avoid burns, allow the projector to cool for at least 60 minutes
before you replace the lamp.
Do not drop the lamp housing or touch the glass bulb! The glass
may shatter and cause injury.
lamp
housing
Be extremely careful when removing the lamp housing. In the
unlikely event that the bulb ruptures, small glass fragments may be
generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing.
screw
6 Carefully remove the lamp housing. Dispose of the lamp in an environ-
connector
mentally proper manner.
7 Install the new lamp housing and tighten the screws.
lamp cable
locking tab
8 Re-attach the lamp connector to the projector. The locking tab should
lamp
housing
engage when the connector is fully plugged in.
screw
9 Replace the lamp door.
10 Plug in the power cord and toggle the Power switch to turn the projector
back on.
11 To reset the lamp hour timer, navigate to the Settings>Service menu
and select Lamp Reset. See page 34 for details.
Service menu
36
Cleaning the Lamp Housing Screens
In dirty or dusty environments, the two dust filter screens in the lamp housing can become clogged, causing high temperatures and premature lamp
failure. Routine maintenance to remove dust from the screens lowers the
lamp operating temperature and prolongs lamp life. To maximize lamp life
you should clean the screen every 250 hours.
lamp housing
lamp
1 Remove the lamp housing.
2 Examine the dust filter screens on the lamp housing. If necessary, use a
vacuum cleaner set on low power to clean the screens. Be careful not to
disturb any internal components when cleaning the screens.
3 Replace the lamp housing and lamp door.
37
two screens
(one on each
side of the
lamp housing)
Accessories
Appendix
Standard Accessories
(ship with the projector)
Specifications
Shipping Box (with packaging)
Temperature
Operating
50 to 104° F (10 to 40° C) at sea level
50 to 95° F (10 to 35° C) at 10,000 feet
Non-operating
-4 to 140° F (-20 to 60° C)
Altitude Operating
Non-operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)
Computer Cable 6 ft (1.8 m)
Audio Cable 6 ft (1.8 m)
RCA to 3.5mm Audio Adapter
RCA Video Cable
Component to S-video Adapter
Power Cable (country-dependent)
Humidity Operating
Non-operating
10% to 95% relative humidity, non-condensing
10% to 90% relative humidity, non-condensing
Remote and Batteries
Dimensions
12.5 x 9.8 x 4.49” (318 x 249 x 114 mm)
Lens Cap
Projection Lamp Housing
(included in projector)
Quick Setup Card
Weight
User’s Guide
6.8 lbs. (3.1 kg) unpacked
Safety Card
Optics Focus Range
4.9 - 32.8 feet (1.5 - 10 m)
Lamp type
150 - W DC SHP lamp
Input Power Requirements 100-120/200-240 3/2A 50/60Hz
Ceiling Mount UL tested/listed ceiling mount with minimum capacity of
34 lbs (15.5 kg)
38
NOTE: Use only approved accessories.
Projected image size
Optional Accessories
Table 2:
Range of distance to the screen for a given screen size for TDP-MT100
Replacement Lamp Housing (TLPLMT10)
For assistance with this projector
Distance to screen
Diagonal
Screen Size
(inches/m)
40/1
50/1.3
60/1.5
100/2.5
150/3.8
200/5.1
For assistance with your Toshiba projector in the United States, please visit
www.toshiba.com/tacp or contact by phone at 800-846-6672.
For assistance with your Toshiba projector in Europe, please visit
www.toshiba-europe.com or contact your local Toshiba dealer.
For assistance with your Toshiba projector in Asia/Japan, please contact
your local Toshiba dealer.
39
Image Width
(inches/m)
32/0.8
40/1
48/1.2
80/2
120/3.1
160/4.1
Maximum
distance
(feet/m)
5.8/1.8
7.8/2.4
8.8/2.7
14.6/4.5
22.6/6.9
30.5/9.3
Minimum
Distance
(feet/m)
4.8/1.5
6,5/2.0
7.5/2.3
12.4/3.8
19.03/5.8
25.2/7.7
Red LED Behavior and Projector Errors
If the projector is not functioning properly and the LED is blinking red, consult Table 3 to determine a possible cause. There are two-second pauses
between the blinking cycles.
Table 3:
Red LED Behavior
Explanation
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
Two (2) blinks
The lamp counter hours have exceeded
lamp life hours. Replace the lamp and
reset the lamp hours counter.
Three (3) blinks
The projector has shut down. Check to
see if the lamp door is open. If the lamp
door is closed, toggle off the projector
and wait one minute, then toggle the projector on again. If the lamp does not strike
after one minute, replace the lamp. Contact your Toshiba dealer for repair if
replacing the lamp does not solve the
problem.
Four (4) blinks
The fan has failed. Contact your Toshiba
dealer for repair or replacing the fan.
Five (5) blinks
The projector is overheating. Check for a
blocked air vent. Contact your Toshiba
dealer for repair if clearing the air vents
does not solve the problem.
40
Computer In connector 12
connecting
video device 6
connectors on projector 7
Contrast 29
customizing the projector 26
Numerics
16x9 vs 4x3 screen aspect 6
800x600 resolution 4
A
About 34
Accessories
optional 39
standard 38
accessories, ordering 38, 39
Advance menu 31
altitude limits 38
Aspect ratio 29
aspect ratio 6
Audio 32
Audio In connector 8, 12, 25
Autosource 32
D
Display Messages 32
DVDs 29
F
Factory Reset 34
focus 11, 14
H
HDTV 4, 29
Horizontal 31
I
B
Blank button 27
Blank Screen 33
blinking green 16
blinking red 16
Brightness 29
IBM-compatible computers 4
image
size 5
image optimization 27
image size
projected 39
C
K
cable box 6
cables
ordering 38, 39
Ceiling 32
Color 29
Color Control 31
Color Space 31
Color Temperature 31
compatibility
IBM-compatible 4
Macintosh 4
video devices 4
component cable connector 9
keypad buttons
projector 25
keystone adjustment 11, 14
L
lamp
ordering 38
Lamp Housing Screens
cleaning 37
lamp replacement 35
Lamp Reset 34
Language 34
LED 16
blinking green 16
41
solid green 16
LED Behavior
red 40
LED behavior 16
lens
cap 38
leveling foot 10
keypad buttons 25
maintenance 35
positioning 5
setting up 5
troubleshooting problems 16
turning off 16
R
M
Rear 32
Red LED behavior 40
replacing the lamp 35
Macintosh computers
compatibility 4
maintaining the projector 35
Menu button 28
menu usage 28
Monitor Out connector 12
Mute button 25
S
Screen Aspect 6
Screen Save 16
Service 34
Service Code 34
Settings menu 32
sharpness 31
solid green 16
solid red 16
Sources 32
Specifications 38
Startup Logo 33
S-video connector 8
System 32
N
NND 32
O
optimizing images 27
optimizing video 26
Overscan 31
P
Phase 31
Picture menu 29
Power connector 12
power cord 9, 12
Power Save 16
Power switch 13
Power-up Source 32
presentation
features 27
Presets 30
projection distance 5
projector
connecting video devices 6
customization 26
T
temperature limits 38
Tint 29
Tracking 31
troubleshooting 16
turning off
projector 16
TV tuner 6
U
USB, using your mouse 12
42
V
vents 3
Vertical 31
Video In connector 8
video optimizing 26
Video Standard 31
volume adjustment 11
Volume button 25
W
Windows 98 15
Z
zoom 11, 14
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement