Briggs & Stratton World Formula 124435-8101-8106-01 Engine Tech Manual
Below you will find brief information for Engine World Formula 124435-8101-8106-01. This manual details the technical specifications and allowable modifications for the Briggs & Stratton World Formula engine used in Quarter Midget racing. It covers engine components, required and allowable modifications, technical procedures, and torque specifications. This ensures fair competition and adherence to QMA rules.
Advertisement
Advertisement
Briggs & Stratton
World Formula
Tech Manual
First Issued: May 22, 2007
Updated: March 21, 2012
Rusty Barnard QMA Tech
© 2009 Quarter Midgets of America, Inc.
WORLD FORMULA CLAIM RULE - For Briggs & Stratton QMA Type Engines
1. All engine claims must follow procedure listed in QMA rule book. Please see Article 6, Section 1
World Formula SUSPENSIONS
1. All suspensions must follow procedure listed in QMA rulebook. Please see Article 6, Section 2
QMA Tech Director
Section 1
General Rules
1.
Only stock Briggs & Stratton World Formula Model # 124435-8101-8106-01 will be used in this class except as provided in this Tech Manual. All parts will be stock unaltered Briggs & Stratton
World Formula parts specifically made for this engine by Briggs & Stratton.
2.
Direct Drive only: Clutches are not allowed.
3.
5.
6.
7.
Unless otherwise specifically required or allowed by this Tech Manual no machining or alterations of any kind will be allowed to the World Formula engine or replacement parts to be used in any World
Formula engine for QMA unless specifically stated in these rules. ALL PARTS ARE SUBJECT TO
COMPARISON WITH A KNOWN STOCK PART.
4.
2.
3.
4.
Modifications or machining of any parts in order to bring them to stated minimum/maximum specs,
(or for any reason). “Blueprinting” is not legal.
5.
Fuel: Gasoline only, no additives. Tech procedure is per QMA Rule Book Article 9.
6.
ALL PERTINANT PENELTIES WILL APPLY.
Section 2
Required Modifications
1. Gearbox: Any gearbox is approved. Crankshaft may be altered only on external output shaft by adding a gear to drive the gearbox. All other modifications to crankshaft are illegal.
Electric Starter: Electric starter must be removed and blower-housing openings must be covered with a fabricated metal cover. You should not be able to see any of the flywheel.
Recoil Starter: Recoil starter must be removed. Starter cup must be cut down or replaced with a flat washer, Briggs Part number 691736 for flat washer. Briggs flywheel nut # 792723 may be used.
Exhaust :Any exhaust gasket allowed (no silicone). Must use exhaust port extension in port.
Minimum of a 0.520 length measured from the bottom of the exhaust flange to the end of the pipe using a depth mic. Any style pipe and max of four, (4) B & S style mufflers only. Any size bolt may be used on exhaust. Any size exhaust bolts may be used.
Oil Breather: Oil breather must vent to catch can under the tail cone within the engine compartment.
Carburetor Overflow: Carburetor overflow may be vented to the ground.
Impulse Fitting on Intake Manifold: Impulse fitting on intake manifold must be filed if impulse type fuel pump is not used.
Scatter shield required. (See page 12) 8.
2
Section 3
Allowable Modifications
1.
2.
3.
4.
Crankshaft Seal: No tech on the crankshaft seal on gearbox side.
Flywheel Cup: Flywheel cup may be cut or replaced with a washer, Briggs Part number 691736.
Briggs flywheel nut #792723 may be used.
Fuel Pump: Fuel pump, B & S part number 557033 may be used. If used, fuel pump must be pulsed from the intake manifold pulse fitting only.
Black Plastic Control Cover: Black control cover B & S part number 557048 and bracket # 555618 including ON/OFF switch may be removed. May be replaced with a metal cover plate (Briggs Plate
5.
6.
7.
Part number 555699) and bolted to top of engine. Blower housing openings must be covered with fabricated metal cover.
Rocker Cover: Rocker cover B & S part number 555528 may be modified for installation of oil breather line fitting. (It is allowable to have secondary drilling of holes in the breather valve area of the valve cover.)
The installation of the Briggs Breather By-pass system, part number 555688, per included ms-3742 sheet. Must be tee into catch can.
Plastic Flywheel Ring Gear: Plastic flywheel ring gear may be removed. No other alterations including the addition or subtraction of metal to the flywheel are allowed.
8.
9.
10.
11.
Heat Dispenser, Briggs part number 555690, may be installed per included ms-3758
Can use Briggs PVL system: Part Number 557127.
Manifold adaptor: Part Number 55769.
Head Gasket Fire Ring: Part Number 55698
12. Flywheel may be lapped stock key must be used. Key must have Briggs logo on key.
Section 4
Tech Procedure
1. General a. b.
Heli-coiled threads for shrouds, (all), valve cover, oil drain, oil fill holes, blower housing, and exhaust pipe attach studs on the head and lower brackets. Any size exhaust bolts may be used.
Blocking airflow: No device may be used that will, or appears that it may impede airflow into the engine cooling system. This may require that the engine be run at a speed above idle by
2. Carburetor the tech personnel at the scale, after the car has qualified or raced.
Remove Carburetor
a. b.
Stock Walbro PZ26 carburetor ending in calibration number .A63 Carb only. No alterations allowed. Slide must remain unaltered. Stock needle marked “CDB” is required.
Needle Jet C-clip must be properly installed but may be installed at any of the 5 factory c. d. e. f. g. h. i. j. k. settings on the needle jet.
Throttle cable cap on the top of the carburetor must be used and properly installed. Cap must be tight.
Choke: Unaltered, but may be fastened open with a spring, rubber band, or zip tie.
OR Remove choke and plug with silicone.
Idle Jets any size allowed.
Main Jets any size allowed.
Venturi Measurement:
Vertical: 25.00mm +/- 0.15mm
Horizontal: 18.50mm +/-0 .25mm
Carburetor Adapter: Carb adapter B & S part number 557050 or updated B & S part number must be used in stock configuration.
Air Filter: B & S part number 698973 is the only air filter allowed but is not required to be used.
Carburetor Overflow: May be vented to the ground.
O-Ring part number B & S part number 557007 is required and must be unaltered.
3
3. Engine Cooling Shrouds/Blower Housing a. b.
All pieces of the stock engine cooling shroud/blower housing must be stock and properly installed. Blower housing thickness 0.115 reference.
Starter cup may be cut down.
Remove blower housing
Remove valve cover
Check:
1.
2.
3.
Max. Valve lift will be checked from the top of the valve spring retainer. Valves must be adjusted to zero clearance.
Valve Lift: First camshaft check will be taken at the valve spring retainers. With the lash set at zero, the movement of the valve spring retainers may not exceed the following:
Intake and Exhaust: 0.310 inches max.
Install Degree wheel, using positive stop method.
Check ignition timing. With the right edge of the magnet, (not the magnet holder), aligned with the right edge of the notch of the right leg of the coil, the engine must be from 23
°
BTDC to 27
°
BTDC You must use stock key way and unaltered flywheel stock Briggs and Stratton only allowed.
Tech camshaft at lifters use approved fixture and dial indicator.
4
.
4. Cylinder Head & Head Gasket
Remove cylinder head.
Head Gasket:
Head:
a. b. a.
Stock, unaltered B & S part number 555698-fire ring gasket allowed.
Minimum gasket thickness between head bold holes .041 inches. Measurements are to be made with dial caliper from inside of fire ring.
Cylinder head, 557101 or 557133 (includes the heat dispenser installed) must be stock, unaltered and be in “ as cast” and in factory-machined condition. No b. additions to or subtractions from any part of head with the exception of Heat
Dispenser, Briggs Part number 555690 may be installed per included ms-3758.
Exhaust pipe attachment stud may be heli-coiled.
4
c. d. e. f. g. h. i.
No alterations of any kind may be made to the intake or exhaust ports.
Combustion Chamber: 19.6 cc to 20.6 cc
Intake Port:
Maximum diagonal measurement = 1.101 inches
Maximum vertical measurement = 1.044 inches
Exhaust Port AS CAST:
Maximum ID of shoulder in bottom of exhaust port =0 .854 inches.
Valve Seats, Intake and Exhaust: Must remain factory spec. with one 45
°
angle only.
Multi angle valve seats are not permitted.
Intake valve seat diameter inside = 0.965 to 0.972 inches.
Exhaust valve seat diameter inside = 0.838 to 0.850 inches.
5
Remove Valves
Inspect retainers for alterations that would increase valve spring pressure. Both intake and exhaust must have stock B & S valve keepers.
5. Valves
a.
b.
c.
d.
Check valves for dimensions and weight. Stock and unaltered B & S part #557018
(exhaust) and #557017 (intake). Valve surface must be unaltered factory ground and have one 45
°
surface only. There will be no other angles ground on any part of the valve.
Valve Guides: Replacement of valve guides with B & S factory part # 555645 only is allowed.
Intake Valve:
Minimum Weight of Valve
Diameter of Valve Stem
Diameter of Valve Head
Diameter of Valve Seat
29.26 grams min.
0.246 to 0.247
1.055 to 1.065 inches
0.965 to 0.972 inches ID
Top of valve stem to top of retainer groove 0.200
Exhaust Valve:
Minimum Weight of Valve
Diameter of Valve Stem
Diameter of Valve Head
Diameter of Valve Seat
28.20 grams min.
0.246 to 0.247
0.935 to 0.945 inches
0.844 to 0.850 inches ID
Top of valve stem to top of retainer groove 0.200
6. Valve Springs
a.
b.
c.
Valve Springs will be dual coil stock, unaltered B & S part # 557024.
Inner Spring
Inner Wire Diameter 0.066 to 0.068 inches.
Outer Spring
Outer Wire Diameter 0.112 to 0.114 inches
6
7. Rocker Arms and Rocker Arm Studs
a. Rocker arms will be stock B & S part # 557015 or 797443 and will not be altered in any way. Note # 797443 and 797441 are part of rocker arm adjuster kit #797440
b.
c. old and new style parts may not be mixed.
Rocker studs will be stock, unaltered B & S part # 555549 OR # 797441 AND in stock location.
Rocker Ball must be stock.
Diameter 0.590 inch min. to 0.610 inch max.
d. Rocker arm mounting positions may not be altered in any manner. No Heli-coiling of mounting holes. No bending of studs. Rocker arm stud plate must be bolted to the head with one stock B & S gasket only – no alterations.
8. Push Rods
a. Push rods will be stock, unaltered B & S part # 555531.
9. Engine Block
a.
b.
Engine block must be in “ as cast - stock factory machined condition with no alterations. There must be no addition or subtractions of metal or any substance to the inside or outside of the cylinder block. There will be no polishing, sand blasting, or glass beading to any interior surface.
No machining of deck surface is permitted.
Cylinder bore may not be oversize. Sleeving is not allowed. c.
d.
e.
f.
Cylinder bore position will not be moved or tipped in any manner.
Cylinder Bore Dimension: 2.688 inches +/- 0.005 max. Taken at top or bottom of bore.
Check Stroke: 2.204. Push piston down to take up rod play.
Cam Shaft Profile Limits
a.
b.
First camshaft check will be taken at the valve spring retainers. With the lash set at zero, (0), the movement of the valve spring retainer may not exceed 0.3097 inches.
Camshaft must be supplied with compression relief.
Tech camshaft at pushrods. Push gently down on dial indicator stem to ensure that there is no lash when push rods are going down.
INTAKE LOBE LIFT EXHAUST LOBE
.050 13 TO 17 BTDC
.150 13 TO 17 ATDC
.200 30 TO 34 ATDC
.050
.100 1 ATDC TO 5 BTDC .100
.150
.200
250 50 TO 54 ATDC .250
(Split)..275 64 TO 67 ATDC .275
309 MAX (107 TO 111 CL.)
(Split)..275 148 TO 152 ATDC
232 TO 236 BTDC
215 TO 219 BTDC
201 TO 205 BTDC
185 TO 189 BTDC
165 TO 168 BTDC
150 TO 154 BTDC
309 MAX. (108 TO 111 CL.)
.275
250 162 TO 165 ATDC .250
.200 182 TO 186 ATDC .200
.150 198 TO 203 ATDC .150
.100 213 TO 217 ATDC .100
.050 228 TO 232 ATDC .050
68 TO 72 BTDC
53 TO 57 BTDC
32 TO 36 BTDC
16 TO 20 BTDC
1 TO 5 BTDC
12 TO 16 ATDC
7
10. Flywheel
a.
b. c. d. e.
No modifications allowed to flywheel.
Stock B & S part # 557126 only. No machining, glass beading, sand blasting, painting or coating of flywheel is allowed.
Flywheels with broken fins must be replaced.
Plastic starter ring gear between flywheel and engine may be removed.
Stock, unaltered flywheel key is required. No offset keyways allowed.
Can use any flat washer under flywheel nut. You can use factory cup.
a.
b.
Red Coil Only - No Other Allowed Coil Part #557125 Flywheel Part #557126
11. Ignition System
Unaltered B & S stock Ignition part # 557125 is mandatory. Only “RED” Coil allowed. Ignition Coil or its position, other than air gap may not be altered in any way. Coil mounting bolts must be stock and cannot be altered in any way to advance or retard timing. Attachment bolts and/or boltholes may not be altered.
Spark plug: Any automotive type with 10mm thread only, unaltered with stock
c.
d.
e. washer allowed. Indexing washers is not allowed. Standard spark plug is Champion
RG519HC.
Magneto air gap is non-tech.
Timing:
Normal = 29
°
BTDC,
Min. = 27
°
BTDC
Max. = 31
°
BTDC
(Space reserved for future use)
8
12. Gear Box
a. Gearbox is not considered part of the engine and in non-tech; therefore any gear reduction box may be used.
Part # 555721 complete gear box
13. Crankcase Cover
Remove crankcase cover
a.
b.
Cover must be in stock, unaltered, “ as cast in factory” condition. No alterations or subtractions of metal or any other substance to crankcase cover.
Crankcase cover gasket must be stock B & S part # 555525. One gasket max. may be installed.
14. Piston
Remove rod and piston.
a.
b.
c.
d.
e.
Stock and unaltered B & S “ kidney bean” piston - part # 557001 only.
Minimum from top of piston to top of wrist pin on circlip side is 0.685 to 0.686 in.
Minimum piston length is 1.768 in.
Oversized pistons are not allowed.
Weight: Complete combination includes piston, rings, rod, clip, cap, and bolts: 300 grams – min. OR 10.6 oz min
NOTE: Torque head assembly- average 357 grams
Hex head assembly- average 360 grams
15. Rings
a. Must be stock; unaltered B & S rings part # 555664 only.
This set contains file to fit top ring.
b. No decreasing of ring tension by heating, machining or any other means.
c.
d.
Three rings mandatory
1.
2.
3.
Top compression ring must have chamfer or O toward top of piston.
Second scraper ring must be installed with inside chamfer down and O toward the top of piston.
Oil ring must be installed as from factory.
Minimum width of top two rings is .095 inches.
e. Thickness of top two rings is .059 to .064 inches. (each ring)
f.
g.
Minimum width of oil ring is .065 inches. Ring groove must be present.
Thickness of oil ring is .098 to .102 inches.
9
16. Wrist Pin
a.
b.
Must be stock, unaltered B & S part # 555520 wrist pin and lock part # 555521
Wrist Pin:
Maximum I.D. = 0.414” +/-
Max. O.D. = 0.626”
Minimum length – 1.901”
17. Connecting Rod
a.
b.
c.
d.
Must be stock, unaltered B & S part # 557005 or 555117 (hex head bolts).
Rod length, measurement from bottom of wrist pin hole of top of crank journal hole is 2.419 inches minimum to 2.429 inches maximum.
Diameter of big end = 27.9476 mm - 1.003” ref
Diameter of small end – 15.89405 mm - 0.625” ref
18. Crankshaft
a.
b.
c.
d.
e.
f.
g.
Stock B & S part # 555620 or 557135 crankshaft must remain unaltered except the following:
Crankshaft may be altered only on external output shaft and only by adding a gear to drive the gearbox. All other modifications to the crankshaft are illegal.
Crankshaft journal diameter = 1.094 inches to 1.100 inches.
Stock, unaltered B & S part # 555573 bearings required.
B & S part 555054 key-flywheel.
Shim, (s), Briggs Part number 55619, if used must be installed as from factory.
Stock, unaltered part # 555574 timing gear installed in stock location on crankshaft only.
No offset keyways allowed on cam gear for crankshaft.
Splined Crankshaft Part #555722
Stock, unaltered B & S part # 557038 tappets only.
Tappet diameter = 0.964 to 0.984 min. max.
20. Tappets
19. Camshaft
a.
b.
c.
d.
e.
a.
b.
Stock, unaltered B & S part # 557041 camshaft.
There will be no additions or subtractions from any part of the camshaft.
Compression release will remain intact and unaltered.
Lobe center angle will not be altered by any means.
Lobe profile will not be altered in any way.
10
Torque Specifications:
Non-Tech, recommended by B & S
Flywheel Nut
Cylinder Head
Connecting Rod
Crankcase Cover
55-75 ft. lbs. (74.5–101 Nm)
180-22- in. lbs. (20-25 Nm)
120-140 in. lbs. (13.5-15.8 Nm)
120-140 in. lbs. (13.5-15.8 Nm)
Cylinder Head Plate
Rocker Arm Stud
Valve Cover
Spark Plug
Intake and Exhaust
Flywheel Holder Tool
Valve Lash
70-90 in. lbs. (8-10 Nm)
70-11- in. lbs. (8-12.5 Nm)
30-60 in. lbs. (3.5 -7 Nm)
95 – 145 in. lbs. (11-16 Nm)
Measured at TDC .005 -.007 in. (.127 - .178mm)
Part # 19372
Cold
11

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Direct drive only
- Electric starter removed
- Recoil starter removed
- Any gearbox approved
- Fuel pump B&S part number 557033 allowed
- Stock Walbro PZ26 carburetor required
- Minimum gasket thickness between head bolt holes .041 inches
- Minimum piston length is 1.768 in.
- Stock, unaltered B&S "kidney bean" piston - part # 557001 only.