Car2U TM Receiver - SmartHome

Car2U TM Receiver - SmartHome
Car2U Receiver
TM
for use with Car2U Universal
Garage Door Opener Transmitter
Models: WDRR-372, WDRR-372R
Operating Instructions
and Owner’s Manual
Your Car2U Receiver is designed to allow you to use your in-vehicle Car2U Transmitter
with any garage door opener. Simply follow the instructions to connect it to the wired
accessory terminal block of your garage door opener, then finish by following the easy
programming steps.
Important Notice!
Read the enclosed instructions carefully before installing the Car2U Receiver. Pay close attention to all
warnings and notes. This manual should be retained for future reference.
Package ContentS
Screw
6-32 X 3/4
Car2U Receiver
6 ft. Twin lead
wire
Table of Contents
Instruction
Manual
Package Contents........................................................................................1
Warnings.....................................................................................................2
Set-up................................................................................................... 3 - 4
Operation.....................................................................................................5
Regulatory Compliance................................................................................6
1
Definition of Symbol
INSTALLATION SAFETY PRECAUTIONS WARNING:
INCORRECT INSTALLATION CAN LEAD TO SEVERE OR FATAL
INJURY. FOLLOW THESE INSTRUCTIONS CAREFULLY.
Warnings
Warning
Before installing this receiver, read the door operator’s instruction manual fully, so you are
aware of all of the unit’s functions and features.
Wear protective gloves to install, repair, or adjust door or operator to avoid injuries.
Wear eye protection when using tools to install, repair, or adjust door or operator to prevent eye
injuries.
Before installing receiver, disconnect all power to door operator to prevent unintended
operation. Disconnect all power to the electrical outlet the Receiver will be plugged into.
Do NOT connect this Receiver to a power source until instructed to do so. Do NOT reconnect
power to the door operator until instructed to do so.
Keep fingers and other body parts away from all moving parts of the door operator system
while the system is being operated.
The door safety beams must be in working order and must not be obstructed during the
programming steps.
WARNING -- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
DEVICE TO RAIN, WATER, OR WET LOCATIONS.
NOT EXPOSE THIS NEVER LET CHILDREN OPERATE, OR PLAY WITH DOOR CONTROLS! KEEP REMOTE CONTROL
AWAY FROM CHILDREN.
ALWAYS KEEP MOVING DOOR IN SIGHT AND KEEP PEOPLE AND OBJECTS AWAY UNTIL DOOR
IS COMPLETELY CLOSED. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
1. Read these instructions.
- IMPORTANT SAFETY INSTRUCTIONS -
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
2
Set-Up
Installation Safety Precautions
1. Make sure Garage Door Opener has been
properly installed in accordance with unit’s
installation instructions.
2. Test and confirm proper operation of the
Garage Door Opener before proceeding with the
installation of this receiver.
Installation
1. Turn off power to the Garage Door Opener
before proceeding.
2. Turn off power to the AC outlet the Car2U
Receiver will be plugged into before proceeding.
Note: This could be the same outlet as in step 1.
3. Remove the screw that attaches the outlet
cover plate. Note: Do NOT remove the cover
plate.
Remove Screw
4. Plug the Car2U Receiver into the AC outlet
positioning it so that the screw mounting flange
hole is aligned with the outlet cover plate screw
hole.
5. Install the screw (provided) through the Car2U
Receiver mounting flange into the outlet and
tighten screw. Be careful not to overtighten.
Insert Screw (Provided)
3
7. Connect the opposite end of the twin-lead
wires to the Car2U Receiver’s relay terminals.
Connect Leads
to Terminals
PROGRAM
FORCE
SW
ADJ.
STATUS
Also, see your Garage Door Opener owner’s
manual for specific wiring instructions.
(If you need to purchase more wire, use only
22AWG or larger; CL2X or better wire.)
Set-Up
6. Connect one end of enclosed twin-lead
wires to the Garage Door Opener push-button
terminals. These terminals are typically labeled
“P.B.” and “COM”.
Hint: Connect to the same two terminals used by
your existing wall control.
P.B. COM OBS
Installation
Connect Leads
to Terminals
8. Fasten the twin-lead wires to the wall or
operator support structure so that it cannot
become entangled with the Garage Door Opener
during operation.
9. Straighten the Car2U Receiver antenna wire
and position it in the most vertical position
allowable.
DO NOT CUT ANTENNA WIRE.
Uncoil Antenna and
Position Vertically
10. Turn on power to the Garage Door Opener
AC circuit and turn on power to the AC outlet the
receiver is plugged into.
4
Operation
Program Button
Red Indicator
Helpful hint: A broom handle can be used to
extend your reach for depressing the program
button.
Step 2. Press and Hold for 1 second Button 3 on
your in-vehicle Car2U Transmitter.
Button 3

Step 1. Go to the Car2U Receiver and press and
release its Program button. (Red indicator
turns ON)
Operation
Use the following procedure for programming
your Car2U Transmitter to the Car2U Receiver.
Note 1: To program your in-vehicle transmitter
Buttons 1 or 2, please see your vehicle’s owners
manual for instructions on programming with
rolling code receivers.
Note 2: A maximum of 8 transmitters can
be programmed to the Car2U Receiver. All
transmitters programmed after the 8th
transmitter, will replace the 8th transmitter.

Step 3. Press and release Button 3 on your invehicle Car2U Transmitter once more to operate
the door. Caution: Door will move if operation is
successful.
Button 3
Reset
Use the following procedure to reset your
Car2U Receiver. This operation will remove
all transmitters programmed to this Receiver.
Program Button
1. Plug the Car2U Receiver into an appropriate
AC outlet.
Red Indicator
2. Press and hold the program button for 10
seconds. The Red Indicator will flash 3 times to
indicate a successful reset.
5
Compliance
FCC and IC Statement
FCC Regulatory Information:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct
the interference by one or more of the following measures:
a) reorient or relocate the receiving antenna,
b) increase the separation between the equipment and receiver,
c) connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IC Regulatory Information:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation of the device.
Cet appareillage numérique de la classe B répond a toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive,
et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu
désirée.
WARNING: Changes or modifications to this receiver not expressly approved by Wayne-Dalton Corp. could void the user’s
authority to operate this equipment.
© Copyright 2006 Wayne-Dalton Corp.
Part No. 0000848
New 7/13/06
You can reach us Toll Free 1-888-827-3667 for Consumer Assistance
or online at www.wayne-dalton.com/access
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement