N600 Wireless Dual Band Router Model WNDR3400v3

N600 Wireless Dual Band Router Model WNDR3400v3
Installation Guide
Step 1:
Step 2:
Step 3:
Unplug the power
to turn off your modem.
Connect one end of the yellow
Ethernet cable to your modem, and
and the other end to the
yellow Internet port on your router.
Plug in, then turn on your modem.
N600 Wireless Dual Band Router
Model WNDR3400v3
Package Contents
Ethernet cable
(not included)
DSL
or cable
Ethernet cable
Router stand
(two pieces)
Wait approximately two minutes
until your modem turns on.
If your modem has a battery backup,
first remove and reinsert the battery
before connecting your
modem to power.
Ethernet cable
Internet
Power On/Off
N600 Wireless Router
Power adapter
Attach the stand to the router:
1. Position the router so that the Power
button is at the bottom and the USB
US
SB
port is at the top.
2. Snap each piece of the stand onto
oa
bottom corner of the router.
N600 Wireless Router
(with stand attached)
Laptop or desktop
computer
Modem
Step 4:
Step 5:
Connect the power adapter to the
router, then plug it into an outlet.
Connect your computer
to the router.
Wait for the 2.4 GHz LED (
2.4 GHz
) to light.
If none of the LEDs light, make sure the
Power On/Off button is in the on position
(pushed in).
Power adapter
Use another Ethernet cable to establish
a wired connection as shown in this diagram.
Optionally, connect wirelessly by using
the preset wireless security settings
located on the product label.
Step 6:
Open a browser.
If the web page doesn’t display,
close and reopen the browser and
enter http://routerlogin.net in the
address bar. The user name and
password are on the product label.
Preset Wireless Security
Connect Wireless Devices to Your Router
Support
This product has a unique WiFi network name (SSID) and network key (password).
The default SSID and password are uniquely generated for every device (like a
serial number), to protect and maximize your wireless security. This information is on
the product label.
Choose either the manual or Wi-Fi Protected Setup (WPS) method to add
wireless computers and other devices to your wireless network.
Thank you for purchasing this NETGEAR product.
NETGEAR recommends that you do not change the preset SSID or password. If you
do change the settings, the information on the product label does not apply.
1. Open the software utility that manages your wireless connections on the
wireless device that you want to connect to your router (iPhone, laptop,
computer, gaming device).
This utility scans for all wireless networks in your area.
Manual Method
2. Look for the preset NETGEAR wireless network name (SSID), and select it.
The preset SSID is on the product label.
Note: If you changed the name of your network during the setup process,
look for that network name.
3. Enter the preset password (or your custom password if you changed it) and
click Connect.
4. Repeat steps 1–3 to add other wireless devices.
Find the preset wireless settings on your router and record them here:
WPS Method
WiFi network name (SSID) _______________________________
You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support resources.
You can get the user manual online at http://downloadcenter.netgear.com or through
a link in the product’s user interface.
For the current EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
For regulatory compliance information, visit
http://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
If your wireless device supports WPS (Wi-Fi Protected Setup), NETGEAR calls
this method Push 'N' Connect, you might be prompted to press the WPS button
on the router instead of entering a password. If you are prompted:
Network key (password) _________________________________
If you change the preset wireless settings, record them here:
1. Press the WPS button on the router.
2. Within two minutes, press the WPS button on the client device, or follow the
WPS instructions that came with your wireless device to complete the WPS
process.
The device is then connected to your router.
WiFi network name (SSID) _______________________________
Network key (password) _________________________________
If necessary to retrieve or update your password, type
http://www.routerlogin.net in a web browser and log in using the
default user name (admin) and password (password).
3. Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a WEP client
to your network using WPS, it does not work.
Select Wireless Settings to locate your wireless password.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
After installing your device, locate the serial number on the label of your product and
use it to register your product at https://my.netgear.com.
April 2014
Download the free genie app from
www.NETGEAR.com/genie.
Internet
WiFi Connection
Router Settings
STATUS GOOD
STATUS Connected
Click here
Network Map
Parental Controls
ReadySHARE
Number of devices 16
Click here
Click here
Easily share media, files, and printers
on the network from your smartphone,
tablet, or laptop.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other
countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising