frigidaire - BrandsMart USA
FRIGIDAIRE
C O M M E R C I A L
COMMERCIAL FREEZER/REFRIGERATOR
GLASS DOOR REFRIGERATOR
TABLE OF CONTENTS
Product Registration………………………………….…..... 2
Important Safety Instructions……………………….…..... 2
Electrical Information…………………………………........ 3
Caster Installation and Setup ........................................ 3-4
Appliance Start-up…………………………………..............4
Features……………………………………………………..... 5
Routine Maintenance……………………………………..… 5-6
Energy Conservation Measures………………………...... 6
Troubleshooting Guide…………………………………...... 7-8
Wiring Diagram……………………………………………....9
READ AND SAVE THESE INSTRUCTIONS
297290801 (March 2009)
Product Registration
Important Safety Instructions
Read all instructions before using this appliance
For Your Safety
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this unit or any other appliance. Read
product labels for flammability and other warnings.
Child Safety
· Destroy carton, plastic bags, and any exterior wrapping
material immediately after the appliance is unpacked.
Children should never use these items for play. Cartons
covered with rugs, bedspreads, plastic sheets or stretch
wrap may become airtight chambers and can quickly
cause suffocation.
These instructions include information which is intended
to assure the operator of correct installation, operation
and service. Before attempting installation, adjustment or
maintenance, be certain of the following:
· That you have read and fully understand the instructions.
· A child might suffocate if he crawls into the appliance to
hide or play. Remove the door/lid of the appliance when
not in use, even if you plan to discard the appliance.
Many communities have laws requiring you to take this
safety precaution.
· That you have all the tools required and are trained to
use them.
· That you have met all installation and usage restrictions
and are familiar with the functions and operations of the
unit.
Proper Disposal of Appliance
· That you follow all instructions exactly as given.
Risk of Child Entrapment
All the fittings, measurements, recommendations and
procedures are significant. Substitutions and approximations
must be avoided. Improper handling, maintenance, installation
and adjustment, or service attempted by anyone other than a
qualified technician, may void the future warranty claims and
cause damage to the unit and/or result in injury to the operator
and/or bystanders.Record Your Model and Serial Numbers
Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators or freezers are still
dangerous – even if they will sit for “just a few days”. If you are
getting rid of your old refrigerator or freezer, please follow the
instructions below to help prevent accidents:
Record your Model and Serial Numbers
· Remove the door.
Record the model number and serial number of this appliance
in the space provided below (the serial plate is located inside
the cabinet compartment).
· Leave shelves in place so children may not easily climb
inside.
· Have the refrigerant removed by a qualified technician.
Model No.
Serial No.
Installetion Date
Invoice Date
Start-up Date
Telephone for Service
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD (shown
above) should be filled in completely, signed and returned to the
address provided.
2
Electrical Information
Caster Installation and Set-up
These guidelines must be followed to ensure that safety
mechanisms in the design of this appliance will operate
properly.
Inspection for Damage
Inspect the underside of the cabinet and packaging for damage,
similar to what can be caused with a forklift. If hidden damage
is found after uncrating, immediately call the delivery carrier
and request an inspection. Retain all packaging and crating
materials until the inspection is complete.
Avoid fire hazard or electric
shock. Do not use an extension cord or an
adapter plug. Do not remove any prong
from the power cord.
Parts and Accessories
Check to make sure that you have received the box containing
all of the components listed below.
A
Carriage Bolt (4)
D
Fixed Caster (2)
B
Lock Nut (4)
E
Hex Screw (10)
C
Swivel Caster (2)
A
B
C
D
E
Tools Needed
The following tools are required to assemble and install the
casters to the unit:
• Refer to the serial plate for correct electrical rating.
The power cord of the appliance is equipped with a
three-prong grounding plug for protection against shock
hazards. It must be plugged directly into its own properly
grounded three-prong receptacle, protected with a 15
amp time delay fuse or circuit breaker. The receptacle
must be installed in accordance with the local codes and
ordinances. Consult a qualified electrician. Receptacles
with Ground Fault Circuit Interrupters (GFCI) are NOT
RECOMMENDED. DO NOT USE AN EXTENSION
CORD OR AN ADAPTER PLUG.
Adjustable
Wrench
5/16”,
3/8”
and
9/16” ADJUSTABLE
3/8”
AND
1/2”
INCH
WRENCH
SOCKET
PLIERS
orOR
Pliers
Socket orWRENCH
Open End
Phillips
1/2”
INCH®FIXED
WRENCH
Screwdriver
Wrench
Uncrating and Set-up
1. Remove carton and all loose parts from inside the unit.
• If the voltage varies by 10 percent or more, appliance
performance may be affected. Operating the appliance
with insufficient power can damage the motor. Such
damage is not covered under the warranty. If you suspect
your voltage is high or low, consult your power company
for testing.
2. Remove the rear access guard and place it and the
screws in a safe place for reassembly later.
• To prevent the appliance from being turned off
accidentally, do not plug the unit into an outlet controlled
by a wall switch or pull cord.
4. Remove the four scews holding the wood skid to the
bottom of the unit using a 3/8” socket wrench. See Figure
1. Discard the wood skid and screws.
• DO NOT pinch, knot, or bend the power cord in any
manner.
5. Remove and discard the two front brackets with leg
leveler using a 5/16” socket wrench. See Figure 1.
3. Using an assistant, carefully tip the unit onto its back and
rest on blocks to avoid damaging the condensate drain
hose and the plastic raceway that covers the evaporator
tubing on the back of the cabinet.
Other Precautions
6. FOR GLASS DOOR MODELS ONLY - Remove bottom
door support bracket and screw opposite the door hinge
using a 3/8” socket wrench. See Figure 2.
• NEVER unplug the appliance by pulling on the power
cord. Always grip the plug firmly and pull straight out from
the receptacle.
• To avoid electrical shock, unplug the appliance before
cleaning.
NOTE: Turning the control to “OFF” turns off the compressor but
does not disconnect power to other electrical components.
3
5. With the help of an assistant, carefully upright the unit.
Reassemble the rear access guard with screws.
Figure 1
CAUTION
Unit will roll forward as it is tipped up.
Brake Lever
Front Bracket
& Leg Leveler
Front
of Unit
Hex Screws(3)
Fixed Caster
Figure 3
Figure 2
Remove Screw Before
Installing Caster
Repeat For
Opposite Corner
Figure 4
Figure 5
Front Fixed Caster Installation
1. Locate and align fixed caster (with brake lever facing
front of unit - see Figure 3) over the same mounting
holes from bracket in Figure 1 using six hex screws (3 for
each caster). Secure the screws snug using a 3/8” open
end wrench. Repeat this procedure for opposite corner.
DO NOT OVERTIGHTEN.
(2) Carriage bolts
with lock nut
Rear Swivel Caster Installation
Swivel Caster
1. Remove and discard the screws shown in Figure 4 from
each bottom corner using a 5/16” socket wrench.
Install caster using
(2) hex screws
Appliance Placement
2. Locate and align swivel caster over the holes and install
with two hex screws. Secure the screws snug using a
3/8” socket wrench. DO NOT OVERTIGHTEN.
Leave a one (1) inch space on all sides and the back of the
cabinet for ease of installation, proper air circulation and
electrical connections. DO NOT block the front grill on the lower
front of your appliance. Sufficient air circulation is essential
for the proper operation of your appliance. Choose a place
that is near a grounded electrical outlet. For the most efficient
operation, the appliance should be located where surrounding
temperatures will not drop below 40ºF (5ºC) or exceed 110ºF
(43ºC). Additional compressor heaters are not recommended.
3. On the opposite side of the swivel caster plate, insert
two carriage bolts through the compressor support rail
and swivel caster plate. Use a lock nut on each bolt and
tighten securely using a 9/16” socket wrench. See Figure
5.
4. Repeat the same procedure for the opposite rear corner.
4
Features
Cool Down Period
For safe food storage, allow 24 hours for the appliance to cool
down completely before loading with food. The appliance will
run continuously for the first several hours. Do not place any
food in the appliance until after the first 24 hours of operation.
Appliance Placement
Thermostat Setting
Leave a one (1) inch space on all sides and the back of the
The appliance
is installation,
shipped from
the factory
with theand
thermostat
cabinet
for ease of
proper
air circulation
electrical
set at aboutDO
the NOT
mid-point
ofthe
the front
operating
connections.
block
grill range.
on theAdjustments
lower front
warmer can
be made
the appliance
has for the
ofcolder
your or
appliance.
Sufficient
airafter
circulation
is essential
been operation
running forofatyour
leastappliance.
8 hours. Allow
at least
8 hours
fornear
proper
Choose
a place
that is
stabilization
before
the thermostat.
a temperature
grounded electrical
outlet.
For re-adjusting
the most efficient
operation,
the appliance should be located where surrounding temperatures
Defrost
will
not dropSetting
below 40ºF (5ºC) or exceed 110ºF (43ºC). Additional
compressor
heaters
are not to
recommended.
The appliance
is designed
defrost automatically every 12
• Heavy duty epoxy powder coated adjustable shelves
• NSF certified top mounted evaporator
• 2-½” urethane foam cabinet insulation
• Torsion spring door closer
• Heavy duty fixed and swivel casters
Features
• 17 watt fluorescent lamp
NSF
FDA Approved
Adjustable
• and
Stainless
steel evaporator
housing Shelving
• appliance
Removable
stainlesswith
steelNSF
drain
cover
This
is provided
and
FDA approved heavy
• epoxy
Adjustable
control shelves. The one with the
duty
powdertemperature
coated adjustable
• that
NSF
certified
wires
are
angledinterior
on the front and back goes on the floor of
• cabinet.
HeavyThe
dutyothers
front grill
the
are placed in the adjustable stainless
• shelf
Heavy
duty commercially
rated
elecrtrical
steel
supports
that clip into the
shelf
supportharness
strips on each
•
Heavy
duty
removable
stainless
steel
shelf support
side of the interior. Make sure to place the shallow
shelf in the
upper-most position.
Insulation
hours. To set the time of defrost, wait until the desired time to
The
insulated
of this
cabinet
sealed
to maintain
defrost.
With space
the notch
on the
timer is
knob
aligned
with the peak
line
efficiency.
Holes(Fig.
drilled
the the
cabinet
may
destroy
seal and
on the bracket
A),inturn
defrost
timer
knobthat
clockwise
damage
electrical
located
the insulated
space.
slowly. The
timer wiring
will click
severalintimes,
then once
loudly,
at
which
point
the
defrost
cycle
begins.
The
timer
knob
will
DAMANGED ELECTRICAL WIRING OR WET INSULATION
advanceBY
through
the defrost
loudly at the end
CAUSED
DRILLING
WILLcycle,
VOID then
THEclick
WARRANTY.
of the cycle. The appliance will defrost automatically every 12
hours after the first
defrost cycle.
Appliance
Start-up
Once
the appliance
located
in its permanent
location
For example,
to sethas
the been
appliance
to defrost
at 10:00 AM,
turn
and
proper
andatgrounding
provided,
thethe
timer
knob power
clockwise
10:00 AM has
until been
the timer
clicks the
following
items
must bewill
checked
completed:
loudly. The
appliance
defrost or
daily
at 10:00 AM and again
12 hours later at 10:00 PM. NOTE: The appliance interior
Cool
Down Period
temperature
will rise slightly during the first defrost cycle.
This appliance
is provided
with four
shelves; one goes on the
Front
Fixed and
Rear Swivel
Casters
floor of the cabinet and the other three are placed in the metal
Glass
door unit come
withthey
two are
(2) front
fixed
casters
with
side supports,
wherever
needed.
The
shallow
shelf
For safe food storage, allow 24 hours for the appliance to cool brakes
and
two
(2)
rear
swivel
casters.
Non-glass
door
unit
goes in the upper position
Insulation
down completely before loading with food. The appliance will comes with two (2) front swivel casters with brakes and two (2)
The
insulated space
of this
sealedDo
to maintain
run
continuously
for the
firstcabinet
severalishours.
not placepeak
any rear
swivel casters. The casters allow the appliance to be
Casters
efficiency.
Holes drilled
in after
the cabinet
destroyofthat
seal and moved with ease and then locked in position at its desired
food
in the appliance
until
the firstmay
24 hours
operation.
The appliance comes with four casters; two with locks for the
damage electrical wiring located in the insulated space.
location.
Thermostat Setting
front of the unit and two without locks for the back of the unit.
DAMANGED
WIRING
The casters allow you to move the unit to it’s final destination
The
appliance isELECTRICAL
shipped from the
factoryOR WET INSULATION
CAUSED
BY DRILLING
WILLthe
VOID
THE WARRANTY.
with ease. The casters can then be locked into place. (Refer to
with
the thermostat
set at about
midpages 3-4 for instructions.)
point
of
the
operating
range.
Adjustments
Appliance Start-up
colder or warmer can be made after the
Adjustable Temperature Control
Once thehas
appliance
has been
appliance
been running
forlocated
at leastin its permanent location
and
the
proper
power
and
grounding
has
been
provided,
the
8 hours. Allow at least 8 hours for
The adjustable cold control is located on the top left side
following items
must be checked
or recompleted:
temperature
stabilization
before
of the evaporator housing inside the unit. “5” is the medium
adjusting the thermostat.
(recommended) setting and “9” is the coldest setting.
NSF Certified Temperature Gauge
Defrost Setting
The appliance is designed to defrost automatically every 12
hours. To set the time of defrost, wait until the desired time to
defrost. With the notch on the timer knob aligned with the line
on the bracket (Fig. A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once loudly, at
which point the defrost cycle begins. The timer knob will advance
through the defrost cycle, then click loudly at the end of the cycle
(Fig. B). The appliance will defrost automatically every 12 hours
after the first defrost cycle.
This appliance
is equipped with
an NSF certified temperature
Adjustable
Temperature
Control
gauge to display cabinet internal temperature. The temperature
The adjustable cold control is located on the top left side of the
gauge is located on the top right side of the evaporator housing
evaporator housing inside the unit. “5” is the medium
inside the unit.
(recommended) setting and “9” is the coldest setting.
Figure A
5
Fig. A
Fig. B
Fluorescent Lamp (Glass Door Models)
Energy Conservation Measures
• The Glass Door Refrigerator is equipped with a 17 watt
fluorescent lamp. A ballast – lamp mismatch may result
in poor or no lighting.
This appliance is designed for efficiency with heavy foam
insulation. However, there are things that the user can do to
maintain the appliance in operating condition.
• Do not operate the appliance any colder than necessary
to maintain safe, product storage temperatures.
• If the lamp fails, replace with a lamp of the same
type and wattage. Also, replace a lamp that flickers
continuously. This could damage the ballast.
• Make sure the appliance is located to prevent direct
exposure to sunlight, air ducts, etc.
• Turning the light off, when not in use, will save energy.
However, frequent ON-OFF cycling will reduce the lamp
life.
• Keep the door closed except for normal use. Inspect the
door often to see that it self-closes and the gaskets are in
good condition.
• Use only NSF certified lamp which can be ordered from
your Frigidaire Commercial Service Center by calling
1-866-738-1640.
• Do not overstock the product in the cabinet because it
will block the normal air flow.
Interior Light (Stainless Steel Door Models)
• Have at least annual inspections by a qualified service
company to see that the refrigerant charge is correct.
The Stainless Steel Door models are equipped with a 40 watt
bulb that lights up when the door is opened. If the bulb goes
bad, replace with bulb of the same type and wattage. This is
a special bulb with a shatterproof coating. Use only an NSF
certified bulb of the same type and wattage which can be
ordered from your Frigidaire Commercial Service Center by
calling 1-866-738-1640.
• This appliance operates more efficiently in a cooler
ambient than in a hot ambient. Try to maintain an ambient
below 80ºF (27ºC) and 65% RH (Relative Humidity) for
maximum efficiency.
Periods of Non-use and Moving Tips
Routine Maintenance
Leave the appliance operating during periods of non-use of less
than three (3) weeks.
Cleaning the Interior
Long Periods of Non-use
Be sure to turn the temperature control to “OFF” and unplug the
electrical cord. Wash the inside surface of the storage area with
warm water and baking soda solution (about one tablespoon
of baking soda per quart of warm water). Rinse thoroughly with
clean, warm water and wipe dry.
If the appliance will not be used for several months:
• Remove all food and unplug the power cord.
• Clean and dry the interior thoroughly.
• Leave the appliance door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
Cleaning the Exterior
Wipe the cabinet exterior occasionally with a cloth dampened in
mild detergent and water. Rinse and wipe dry with a soft cloth.
Do not use razor blades or other sharp instruments that can
scratch the appliance surface when removing adhesive labels.
Any glue left from the tape can be removed with a mixture of
warm water and mild detergent or touch the residue with the
sticky side of tape already removed. DO NOT REMOVE THE
SERIAL PLATE.
Moving
When moving the appliance , follow these guidelines to prevent
damage:
• Disconnect the power cord plug from the wall outlet.
• Remove foods, then defrost, and clean the appliance .
• Secure all loose items such as base panel, baskets,
and shelves by taping them securely in place to prevent
damage.
Condensate Pan
Some models have a condensate pan in a fixed position located
behind the toe grill. This must not be removed from under the
cabinet. If the pan is removed, condensate will drop onto the
floor.
• In the moving vehicle, secure appliance in an upright
position to prevent movement. Also, protect outside of
appliance with a blanket or similar item.
Power Failure
DO NOT open the appliance lid unnecessarily if the appliance is
off for several hours.
If a power failure occurs, pack seven or eight pounds of dry ice
into the appliance every 24 hours. Look in the Yellow Pages
under “Dry Ice”, “Dairies”, or “Ice Cream Manufacturers” for local
dry ice suppliers. Always wear gloves and use caution when
handling dry ice.
6
TROUBLESHOOTING
GUIDE
PROBLEM
Before calling for service, review this list. It may save you time and expense. This list includes
common occurrences that are not the result of defective workmanship or materials in this
appliance.
CAUSE
CORRECTION
APPLIANCE OPERATION
* Appliance is plugged into a circuit
that has a ground fault interrupt.
* Temperature control is in the "OFF"
position.
* Appliance may not be plugged in, or
plug may be loose.
* House fuse blown or tripped circuit
breaker.
* Power outage
Appliance runs too much or * Room or outside weather is hot.
too long.
* Appliance has recently been
disconnected for a period of time.
* Large amount of warm or hot food
have been stored recently.
* Door is opened too frequently or
kept open too long.
* Appliance door may be slightly
* Temperature control is set too low.
Appliance does not run.
* Appliance gaskets are dirty, worn,
cracked or poorly fitted.
Interior appliance
temperature is too cold.
Interior appliance
temperature is too warm.
Appliance external surface
temperature is warm.
* Temperature control is set too low.
* Use another circuit. If you are unsure about the outlet,
have it checked by a certified technician.
* See Thermostat Setting.
* Ensure plug is tightly pushed into outlet.
* Check/replace fuse with a 15 amp time delay fuse.
Reset circuit breaker.
* Check house lights. Call local Electric Company.
* It's normal for the appliance to work harder under
these conditions.
* It takes 24 hours for the appliance to cool down
completely.
* Warm food will cause appliance to run more until the
desired temperature is reached.
* Warm air entering the appliance causes it to run
more. Open the door less often.
* See "Door Problems".
* Turn control knob to a warmer setting. Allow several
hours for the temperature to stabilize.
* Clean or change gasket. Leaks in the lid seal will
cause appliance to run longer in order to maintain
desired temperature.
* Turn control knob to a warmer setting. Allow several
hours for the temperature to stabilize.
* Turn control knob to a colder setting. Allow several
hours for the temperature to stabilize.
* Warm air entering the appliance causes it to run
more. Open the door less often.
* See "Door Problems".
* Wait until the appliance has had a chance to reach its
selected temperature.
* appliance requires 24 hours to cool down completely.
* Temperature control is set too
warm.
* Door is opened too frequently or
kept open too long.
* Appliance door may be slightly
* Large amount of warm or hot food
have been stored recently.
* Appliance has recently been
disconnected for a period of time.
* The external appliance walls can be * This is normal while the compressor works to transfer
heat from inside the appliance cabinet.
as much as 30ºF warmer than room
temperature.
SOUND AND NOISE
Louder sound levels
whenever appliance is on.
Louder sound levels when
compressor comes on.
Popping or cracking sound
when compressor comes
on.
* Modern appliances have increased * This is normal. When the surrounding noise level is
storage capacity and more stable
low, you might hear the compressor running while it
temperatures. They require heavy
cools the interior.
duty compressors.
* Appliance operates at higher
* This is normal. Sound will level off or disappear as
appliance continues to run.
pressures during the start of the ON
cycle.
* Metal parts undergo expansion and * This is normal. Sound will level off or disappear as
contraction, as in hot water pipes.
appliance continues to run.
7
CAUSE
PROBLEM
CORRECTION
SOUND AND NOISE (Cont.)
Bubbling or gurgling sound, * Refrigerant (used to cool appliance) * This is normal.
is circulating throughout the system.
* Level the appliance by putting wood or metal shims
Vibrating or rattling noise.
* Appliance is not level. It rocks on
under part of the appliance.
the floor when it is moved slightly.
* Floor is uneven or weak.
* Ensure floor can adequately support appliance. Level
the appliance by putting wood or metal shims under
part of the appliance.
* appliance is touching the wall.
* Re-level appliance or move appliance slightly.
WATER / MOISTURE / FROST INSIDE APPLIANCE
Moisture forms on inside
appliance walls.
* Weather is hot and humid, which
* This is normal.
increases internal rate of frost buildup.
* See "Door Problems".
* Door is slightly open.
* Door is kept open too long or is
* Open the door less often.
opened too frequently.
ODOR IN APPLIANCE
Odors in appliance.
* Interior needs to be cleaned.
* Foods with strong odors are in the
appliance.
* Clean interior with sponge, warm water, and baking
soda.
* Cover the food tightly.
DOOR PROBLEMS
Door will not close.
* Appliance is not level. It rocks on
the floor when it is moved slightly.
* Level the appliance by putting wood or metal shims
under part of the appliance.
* Floor is uneven or weak.
* Ensure floor can adequately support appliance. Level
the appliance by putting wood or metal shims under
part of the appliance.
LIGHTING PROBLEMS
Light bulb is not on.
* The fluorescent lamp or light bulb is * See "Fluorescent Lamp" or "Interior Light" on
burned out.
Features Section.
* No electric current is reaching the
* See "appliance Does Not Run".
appliance.
8
IMPORTANT SAFETY NOTICE
The information provided herein is designed to assist qualified repair personnel only.
Untrained persons should not attempt to make repairs due to the possibility of electrical
shock. Disconnect the power cord before servicing.
ELECTRICAL CIRCUIT
STAINLESS STEEL DOOR STAINLESS STEEL DOOR
REFRIGERATOR
FREEZER
GLASS DOOR
REFRIGERATOR
IMPORTANT
IF ANY GREEN GROUNDING WIRES ARE REMOVED DURING SERVICING, THEY MUST BE RETURNED
TO THEIR ORIGINAL POSITION AND PROPERLY SECURED.
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement