SP-502 - Crimestopper
SP-502
2-Way LCD Paging Alarm & Remote Engine Starting System
OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of the SP-502 by Crimestopper Security Products Inc. This booklet contains the
information necessary for operating your system. If any questions arise, contact your installation dealer or
Crimestopper Security Products Inc.
CONTACT INFORMATION:
TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific
Website: www.crimestopper.com
CRIMESTOPPER
SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063
REV 08.2012
This device complies with FCC Rules part 15. Operation is subject
to the following two conditions: 1) This device may not cause
interference, and (2) this device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. Such modification could void the user's authority to
operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings……..…………..……………………………………………………………………2
Using The 2-Way Pager…………….....…………..……………………………………………………………….…3-4
Setting the Clock and Beep or Vibrate Selection….…………………………………………………..…...…...4-5
1-Way Sidekick and Battery Replacement…………………………………………………………..………….…...6
Quick Chart Button Functions...………………………….…………………………………………………..…...…..7
Operating Instructions - Alarm……………………………………………………….………..……………..…...8-11
Remote Engine Controls (Idle Down, Self Start, Turbo Timer)…………….…………….……………..….12-16
Manual Transmission Mode….………….……………….……………………..…………………………………....17
Anti-Carjack Protection...……………………………………….………….……..………………..………..………..18
LED and Remote Start Diagnostics………………..……………………………………………….………..….…19
Transceiver / Remote Control Programming……………………………………………………..……………….20
2 Vehicle Operation……...………………………….……………………………….………….…………….….……21
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident
resulting from the use of this equipment. This system is designed to be professionally installed into a car or
vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,
must be in perfect working condition.
DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to
repair and / or replacement charges.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this
system and its safety features. B) Check for proper operation of these safety features prior to accepting
delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all
items relative to the proper operation of this system and its safety features.
DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door
is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death
from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature
of the unit
2
USING THE 2-WAY PAGER TRANSMITTER
SIDE BUTTONS
LCD SCREEN ICONS
Valet Mode
(Tools)
Transmit Signal
Battery Life
Ignition ON
Hood Open
Lock/Unlock
(Arm/Disarm)
Silent no beeps
Sensor Warning
(Small Hammer)
Sensor Trigger
(Big Hammer)
Door Open
CLOCK /
Run Count Down
VEHICLE
SELECT
Trunk Open
Remote Started
LOCK / ARM
TRUNK
RELEASE
UNLOCK / DISARM
REMOTE
START
USB Charger
(Under Side Cover)
AUX Outputs thru Data
AUX 1 = Trunk + Lock
AUX 2 = Trunk + Unlock
AUX 3 = Trunk + Start
AUX 4 = Lock + Start
POWER OFF FUNCTION
To turn Power ON, press and hold unlock button 2 seconds.
To turn Power OFF, press and hold unlock button 5 seconds.
3
This remote can control up to 4 AUX
functions thru data depending on the
vehicle and data module. This is typically
used for operating left and right sliding
doors. (Requires Canbus Data Module)
USING THE 2-WAY PAGER TRANSMITTER
The 2-Way LCD Pager remote transceiver is used to send and receive information from the vehicle. The
Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your
range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed
to page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels
of electronic interference. Handle the pager/remote with care. The LCD display and/or the electronics may be
damaged if subjected to abuse.
BATTERY CHARGING
The 2-Way LCD remote has a battery charge indicator on top right corner of display. The battery
voltage affects the distance of the remote control. The system comes with a standard Mini USB
charging cable that plugs into the side of remote control. To access to USB plug, slide the cover to the
left shown below.
USB Charging Port
SETTING THE CLOCK (2-WAY- LCD REMOTE)
1.
2.
3.
4.
5.
6.
7.
Press VEH Button on the side of the remote control 5 times.
The remote will beep and the AM or PM display will begin flashing.
Press the Trunk Button to go to the next item – AM - PM - Hour- Minutes.
Press the Lock Button to Increase time.
Press the Unlock Button to decrease time.
Press the Start Button to Disable or Enable Beep and Vibration. See next page.
Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
4
REMOTE BEEP & VIBRATE SELECTION
The LCD pager remote BEEPS and VIBRATES when it receives a signal from the vehicle. The Beeps and
Vibration are selectable (on/off). To enter program mode,
1.
2.
3.
4.
Press VEH Button on the side of the remote control 5 times.
The remote will beep and the AM or PM display will begin flashing.
Press the Start button to choose the mode of “Beep ON/OFF & Vibrate ON/OFF”.
Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
Mode 1: The remote beeps once and vibrates: this indicates “Beep ON & Vibrate ON”.
Mode 2: The remote beeps once without vibration; this indicates “Beep ON & Vibrate OFF”.
Mode 3: The remote only vibrates, without beep; this indicates “Beep OFF & Vibrate ON”.
Mode 4: The remote does not vibrate or beep; this indicates “Beep OFF & Vibrate OFF”.
5
1-WAY SIDEKICK
The 1-Way sidekick remote adds flexibility to your system. You can have the convenience of operating your
system without needing to carry the larger pager remote. The Sidekick remote has less range and offers all of
the same operation features except for page-back confirmation. The 1-Way Sidekick Remote uses three CR2016 Lithium 3 Volt Batteries.
To replace the battery on Sidekick:
Simply remove the two Phillips screws holding the back cover in place. Side old batteries out and remove
plastic cover. Insert the new batteries into plastic cover and slide into place with the (+) end facing up. The
plastic cover keeps the batteries from shorting out against the side of metal housing.
ARM /
LOCK
DISARM /
UNLOCK
TRUNK
START
VEH
Back Cover
CR2016
VEH1 / VEH 2
2 Screws
6
QUICK CHART BUTTON FUNCTIONS
Button
Plus
CLOCK SETUP:
Button Functions Button Options
Lock Doors & Arm
System
Press and Hold 2
Seconds for Panic
Mode
Unlock Doors &
Disarm System
Trunk Pop Aux # 1
Button
Button Functions Button Options
VEH
Selects between
Vehicle #1 and
Vehicle #2
Press and Hold for 2
seconds
Press twice for
second door unlock
VEH
Change Clock Time
Press 5 Times
AM/PM Flashes
Press and Release
for Trunk Pop Aux #1
Plus
Activates Aux #1 thru Data Module Sliding
Door
Data
Press for Remote
Start or Stop engine Start. Three options
available
Plus
Activates Aux #2 thru
Data or wire
Silent Arm / Disarm
No Arm / Disarm
Chrip from Siren or
Horn
Plus
Activates Aux #3 thru Momentary, Timed or
Latched Output
Data or wire
Valet Service Sensor
ON / Off
Valet Mode when
Disarmed. Sensor
On/Off when Armed
Plus
Steady Momentary
or Data Module
Sliding Door
Activates Aux #4 thru Momentary, Timed or
Latched Output
Data or wire
Press VEH button 5 time to enter program mode. The AM or PM will start flashing.
Lock = Increase, Unlock = Decrease, Trunk = Next, Start = Beep / Vibrate On or Off, VEH = Save & Exit
7
OPERATING INSTRUCTIONS - ALARM
ARMING / LOCKING
Press the Lock Button on the remote control. The System will arm emit one siren chirp, one light flash, and
the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. The 2-Way
LCD Pager will beep once while displaying a Locking symbol. After a short delay to allow the vehicle and
electronics to settle, the system will be completely armed.
DISARMING / UNLOCKING
Press the Unlock Button on the remote control. The System will disarm and confirm with two siren chirps, two
light flashes, and the LED will turn off. Power locks will unlock and Interior Dome light will turn on (if installed
with these optional features). The 2-Way LCD Pager will beep twice while displaying an Unlock symbol.
SELECTIVE SILENT ARMING / DISARMING
To Arm or Disarm the system without siren chirps, press and release both the Unlock and Start
Plus
Button at the same time. The System will Arm or Disarm without siren chirps. Flashing lights and
LED will be the only indicators of Arm/Disarm status. The LCD will Display a musical note with an “Ø” when
the system is armed or disarmed without a chirp.
DRIVER’S DOOR PRIORITY UNLOCK: Optional connection required
This option separates unlock of the driver’s door from the passenger doors with the remote control. The first
press of unlock button will unlock just the driver’s door. Pressing the unlock button a 2nd time within 12
seconds will unlock the passenger doors.
DISARMING WHILE TRIGGERED
Disarming the System while it is triggering requires TWO presses of the Unlock Button. The first press Resets
the alarm cycle only (system still armed) while a second press will disarm/unlock the system.
SELECTIVE SHOCK SENSOR DISABLE
To arm the alarm and bypass shock sensor protection, press the Lock Button as normal then
press and release the Lock & Unlock Button together within 2 seconds. You will hear 3 extra siren
chirps indicating the shock sensor bypass for this arming cycle only. This is feature useful when parking near
railroad tracks, airports, or areas with excessive loud machinery or noise to prevent the nuisance of
unnecessary false alarms.
8
OPERATING INSTRUCTIONS - ALARM
ALARM TRIGGERS
If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on, the alarm will
sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will
remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle
a maximum of 2 minutes and continue to protect the other un-tampered or unopened zones.
LCD REMOTE PAGING / ZONE VIOLATIONS
When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will
receive a paging signal that will light up the LCD Screen Red. The display will show an icon of what caused
the violation. The paging remote will also vibrate and beep to notify you the vehicle has been tampered with.
OPEN DOOR ALERT / BYPASS
Upon arming, this system will warn you 5-60 seconds later if a door is left open. The LCD pager will vibrate
and beep (5X’s) along with displaying the open zone on your LCD screen. This zone will be bypassed until the
door is closed; otherwise, the alarm will continue to protect all other zones.
PRE-WARNING SHOCK PROTECTION
The Pre-Warning (Warn-A-Way) feature will activate when a low-level shock or vibration is detected by the
system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any
further tampering with the vehicle. The pager / remote will beep and show a Hammer Icon.
PASSIVE ARMING MODE (Programmable)
Passive (automatic) Arming occurs 30 seconds after the ignition is turned off and the last door is closed.
Upon closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive
countdown. If a door is re-opened within the 30-second period, the countdown stops and begins again when
the door is closed. Passive arming provides failsafe protection in case you forget to arm the system.
PASSIVE LOCKING (Programmable)
The system can be programmed to passively lock the doors when the system passively arms or rearms. The
default setting is OFF because passive locking increases the risk of locking the keys in the vehicle when the
system arms/locks passively, without you pressing the remote.
9
OPERATING INSTRUCTIONS - ALARM
REMOTE PANIC PROTECTION
To sound the alarm in an emergency or to draw attention to your vehicle, press and hold the Lock button for at
least 3 seconds until the siren / horn sounds. Press the Unlock button to reset panic mode. The LCD display
will flash most of the icons and emit 10 beeps when the Panic Mode is triggered.
TRUNK / HATCH POP (Optional, Remote AUX. 1 Output)
This feature is designed to interface with existing Factory power trunk or power hatch release systems and
may require additional parts and/or labor charges. To eliminate the possibility of accidentally opening the
trunk, there are (3) options for button press selection. This option will allow you to change whether the Remote
starter and Trunk release activate by a:
1. Double button ½ second presses.
2. Single ½ second press. *Default = Single ½ second press*
3. Press and Hold 2 seconds. This output stays on until trunk button is released.
REMOTE AUX. 1 thru Data module for sliding doors only
This feature requires a Databus module to operate.
Plus
Press Trunk plus Lock at same time to activate Aux 1.
REMOTE AUX. 2 Output (Optional, requires special programming)
This system contains a 2nd Auxiliary output to activate other accessories or devices. This
Plus
momentary output will stay active as long as the remote button is held down. There is no LCD /
Pager confirmation for Aux. 2 output. To activate the 2nd Auxiliary output:
Press the Trunk and Unlock button for more than 2 seconds.
REMOTE AUX. 3 Output (Optional, requires special programming)
This system contains a 3rd Auxiliary output to activate other accessories or devices. This output
Plus
is programmable for a momentary, timed or Latch output. To activate the 3rd auxiliary Output:
Press the Trunk and Start Button at the same time.
REMOTE AUX. 4 Output (Optional, requires special programming)
This system contains a 4th Auxiliary output to activate other accessories or devices. This output
is programmable for a momentary, timed or Latch output. To activate the 4th auxiliary Output:
Plus
Press the Lock and Start Button at the same time.
10
OPERATING INSTRUCTIONS - ALARM
PRIOR INTRUSION ALERT
This system will notify you if the alarm was triggered while you were away. Upon disarming, there will be four
additional siren chirps after the two normal disarm chirps. Check your vehicle for any signs of a break in or
tampering. Also, see LED Diagnostics (page 17) to determine the cause of the trigger.
DOME LIGHT ILLUMINATION (Optional)
This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and
turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.
EMERGENCY OVERRIDE (Disarm)
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to
disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the
override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you
can repair/replace the remote. Valet Mode also prevents Passive Arming.
VALET MODE (Solid Blue LED)
Disables alarm system and remote engine starting for vehicle servicing. The alarm system must be disarmed
to enter Valet Mode.
1. To Activate Valet Mode Manually: Turn the ignition on and press the Valet / override button [about 5-6
seconds] until you hear (3) siren chirps and the LED turns on solid. Repeat the process to exit VALET
mode.
2. To Activate Valet Mode with the Remote: Press and hold both the Lock and Unlock Button
together for about 3 seconds until 3 chirps are heard. Repeat this step to exit via the remote
transmitter. Lock / Unlock and AUX features will still operate in VALET Mode however; Remote Start
and Alarm functions are inhibited.
11
REMO
REMOTE ENGINE CONTROLTE ENGINE CONTROL
REMOTE START & Trunk Release – Button Press Selection (Option # 8)
To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for
button press selection. This option will allow you to change whether the Remote starter and Trunk release
activate by a:
4. Double button press.
5. Single ½ second press.
6. Press and Hold 2 seconds.
*Default = Single ½ second press and release*
REMOTE ENGINE STARTING
1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.
(Chirps can be programmed on or off-See installation manual.)
2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.
3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.
4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.
5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can
be turned off with remote transmitter.
SOLID
FLASH 1X
AFTER
IGN
PRESS START
3
SEC.
THEN
SOLID
STARTER
REMOTE ENGINE STARTING – LCD PAGER-REMOTE:
When requesting a remote start the LCD pager remote will confirm with an Ignition Icon along with 3 beeps.
Once the vehicle has successfully started the remote will confirm back with 3 beeps and vibration, a Key Icon
and smoke coming from car. The LCD screen will display the remaining engine run time every minute.
12
REMOTE ENGINE CONTROL
UNSUCCESSFUL REMOTE START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then
attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank
time of up to4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to
4 seconds to help prevent damage to the starter from over cranking.
1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 (on last page) under "Successful Start".
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER
ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON
AGAIN.
TURNING OFF YOUR REMOTE STARTED ENGINE (VIA Remote Control)
1) Engine is running in Remote Start (Parking lights ON).
2) Press Remote Start button on remote transmitter.
3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.
PRESS START
ENGINE & LIGHTS OFF
ENTERING YOUR REMOTE STARTED VEHICLE
1) With engine running, use remote to Unlock/Disarm system (If armed) or open door with key.
2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key
is now controlling your vehicle.
13
IDLE DOWN MODE
IDLE DOWN MODE (Option # 26 – 10, 20, 30 minutes or Infinity Run)
This mode allows the unit to take over operation of your idling, parked vehicle while the ignition key is
removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will
remain running for the programmed run time, until you return, or until the remote start button is pressed.
Example:
You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you
exit the vehicle, (with keys in hand) remote lock/arm alarm. When you return, unlock/disarm alarm, turn
ignition ON and drive away.
IDLE DOWN MODE - Exiting The Vehicle:
1) With engine running, press Remote Start button on remote transmitter. Siren will chirp 3 times for
confirmation.
2) Parking Lights will turn ON.
3) Doors will unlock, or if brake pedal is being depressed then doors will unlock when it is released.
4) Turn OFF Ignition and remove key. Engine should remain running.
5) Exit vehicle, then arm system with remote if desired. Locking doors a 2nd time aborts remote start.
6) Engine will remain running for programmed run time, until you return, or press the remote start button.
SOLID
IGN
OFF
PRESS START
UNLOCK
IDLE DOWN INFINITY RUN MODE
Idle Down can be programmed for INFINITY RUN. This allows the vehicle engine to remain running
INDEFINITELY without the ignition key in the switch. The parking lights continuously flash in this mode. This
mode can be beneficial to law enforcement or commercial trucks that need to remain running unattended for
long periods of time.
14
TIMED SELF STARTING MODE
TIMED SELF START MODE
This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run
time. This can be helpful during extremely cold conditions where engine or fluid freeze-up is a concern. !!THE
VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA!!
TIMED SELF-START MODE – Exiting the Vehicle:
1) Have engine running with the Key, then press the Start button on the transmitter.
2) Within 10 seconds press the valet/program button once.
3) Parking Lights will turn OFF for about 5 seconds, and doors will unlock.
4) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
5) Press the remote start button again to turn off the engine. The parking lights will flash 4 TIMES as a
confirmation that the unit is in Timed Self-Start Mode.
6) The Vehicle will Start by itself every 4 hours, or until driven with key or started via remote control.
SOLID
WITHIN 10 SEC.
PRESS 1X
PRESS START
LIGHTS OFF 5 SEC.
UNLOCK
FLASH 4X
IGN
OFF
PRESS START
LOCK
RESETTING TIMED SELF START MODE
To reset the timed self-start mode, start vehicle using the ignition key or the remote control.
15
TURBO TIMER MODE
TURBO TIMER MODE (Option # 31)
The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running
for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. The Default = OFF.
To Activate Turbo Timer:
With the engine running by key, press Remote Start Button with brake pedal depressed. As you release
the brake pedal, the Parking Lights and Status LED will blink the number of minutes for the Turbo Timer
setting. The doors unlock after confirmation.
RUNNING
LIGHTS
FLASH 1-5X
PRESS
AND HOLD
BRAKE
PRESS START
RELEASE
BRAKE
REMOVE KEY
EXIT VEH.
16
REMAIN
RUNNING
1-5 MIN.
MANUAL TRANSMISSION MODE
MANUAL TRANSMISSION EXIT PROCEDURE (Option #15-1, 15-3 and 15-4)
This system features a Manual Transmission Mode. When exiting the vehicle, there is safety check out
procedure required for the manual transmission mode to work. There are 3 choices of operation,
1. Option 15-1: With engine running and vehicle in neutral, set parking brake, then press “KEY” Icon on
transmitter. The remote starter will turn on and take over operation of the vehicle.
2. Option 15-3: With engine running and vehicle in neutral, set parking brake, the remote starter will turn
on and take over operation of the vehicle.
a. Remove key, exit vehicle (remote starter unit must “SEE” door opened, then closed with engine
running).
b. Press Lock button within 10 seconds of closing door to “Arm with Idle Down” (engine stays
running). Press Lock a 2nd time to cancel “Idle Down” (engine turns off) and set up Manual
Transmission Mode.
c. Press Lock button after 10 seconds to Arm system, lock the doors and shut down the engine.
From this point, you can will remote start the engine unless a door is opened.
d. Press the Remote Start Button after closing door to set up Manual Transmission Mode without
Arming Alarm System.
3. Option 15-4: With engine running and vehicle in neutral, set parking brake, the remote starter will turn
on and take over operation of the vehicle. Remove Key and exit vehicle. When the last door of vehicle is
closed, the engine will turn off in 2 seconds and set up Manual Transmission Mode. You can arm the
alarm system to lock doors and protect vehicle.
NOTE: Passive arming does not work in Manual Transmission Mode. This system can be programmed to lock
the doors when remote start aborts (engine turns off).
TURBO TIMER in Manual Transmission Mode:
For Turbo Timer, press brake pedal before setting parking brake or pressing the Remote Start Icon (requires
Turbo Timer Option # 31). After exiting vehicle, press lock button to set Manual Transmission Mode. The
engine will remain running for the Turbo Time setting (1, 3 or 5 minutes). Turbo Timer does not work with
option 15-4 selected.
17
ANTI CARJACK PROTECTION
CARJACK PROTECTION (Option 32-1)
This optional feature requires installation of a hidden momentary button or an On/Off switch for Carjack
protection. Carjack provides protection while driving your vehicle. If a Carjacker opens, any door with the
ignition on, the system arms. When the door closes, the parking lights will flash 2 times and the LED will begin
to flash rapidly to confirm the beginning of a Carjack countdown. 30 Seconds later, the unit will begin a
Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full system activation with siren,
horns and flashing lights for up to 5 min. Turning the Ignition off during a Carjack trigger will stop the siren and
lights and horn but Carjack protection is still active. If the Carjacker tries to turn the Ignition back ON, the
vehicle will not start and the Siren and Lights and horn will resume for 5 minutes or until the ignition turns off.
To Reset Carjack During Countdown: Press the UNLOCK button on the remote control, the siren will chirp
once and the LED will stop flashing.
To Reset Carjack after Trigger: With the ignition key on, press and hold the override button for at least 5
seconds.
HIDDEN SWITCH-CONTROLLED CARJACK
This configuration will enable the vehicle owner to activate a Carjack countdown by pressing a hidden pushbutton (not included with kit) during a Carjack situation. A Carjack countdown will begin under the following
conditions: Ignition is ON (vehicle is running), the push-button is pressed, and the door opens/closes. Upon
these three events, in that order, the alarm will start a Carjack countdown. After a delay of 30 seconds, the
system will begin chirping for 20 seconds then trigger into a full cycle for up to 5 minutes.
SWITCH-CONTROLLED & FULL TIME CARJACK
This is the recommended method. A hidden on/off switch is installed on the Pink Carjack wire. For Carjack
protection, simply turn on the switch. Turn off the switch to disable Carjack protection. You can leave the
switch on for full time protection. Just remember to press the unlock button every time the door is opened
while driving.
18
ALARM TRIGGER DIAGNOSTICS
This systems includes disarm diagnostics, through the LED light, that will help in determining what caused the
last trigger of the alarm system. This is a valuable tool in determining how the vehicle was tampered with or if
there is a false alarm problem, in which case you can make the necessary adjustments to correct the problem.
When the system is disarmed with the remote, you will hear the normal 2 chirps, then 4 quick chirps that
indicate the alarm was triggered while you were away. Check the LED light for a sequence of flashes:
1 LED Flash = Shock Sensor Violation
2 LED Flashes = Door Violation
3 LED Flashes = Hood Violation
4 LED Flashes = Ignition Violation
5 LED Flashes = Trunk Violation
Diagnostics will reset when the Ignition is turned on or when the system is re-armed.
REMOTE START DIAGNOSTICS
The system has built-In Remote Start Diagnostics. If Remote Start fails, the Status LED and Parking
Lights flash one to seven times to indicate an error code. The LED will continue flashing the error
code until the ignition is Turned On; it means the following:
1 Parking Light Flash (1 LED Flash) = Problem with Brake Switch.
2 Parking Light Flashes (2 LED Flashes) = Problem with Hood Switch.
3 Parking Light Flashes (Solid LED) = Valet Service Mode.
5 Parking Light Flashes (5 LED Flashes) = Tach Problem (Ignition On before Remote Start).
7 Parking Light Flashes (7 LED Flashes) = Manual Transmission Error.
Note: In Manual Transmission Mode, the LED will Flash 3 times if the parking park is not set.
This system includes disarm diagnostics, through the BLUE LED light, that will help in determining
7 Parking Light Flashes = Manual Transmission Mode Error.
19
TRANSCEIVER / REMOTE CONTROL PROGRAMMING
Note: All transmitter codes must be learned at time of programming! This system learns up to 4
different transmitter codes.
1. Turn ignition key to the ON position.
2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times.
3. Press button #1 of the first transmitter. You should get 1 light flash confirming the remote is coded, then
press button #1 of a second transmitter, the unit will flash 2 times confirming the remote is coded and so
on. If all 4 codes are learned, the unit will automatically exit code learning mode, otherwise turn key off.
See diagram below.
IGN
OFF
WAIT FOR
4 FLASHES
PRESS 4X's
IGN
OFF
FLASH 2, 3, or 4 X's
COMPLETE
PRESS LOCK
20
2 VEHICLE OPERATION
2 VEHICLE CONTROL
Your remotes have the ability to control a second vehicle with a Crimestopper system installed.
To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter
Programming” steps (Pg. 17) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing
remotes.
2-VEHCLE NOTES:
(1) You do not have to switch between Vehicle “1” and “2” to get pages from each vehicle. Your remote pager
will receive pages from both cars regardless of which vehicle the pager is set to. The “1” or “2” icon will
always display with each page indicate which vehicle the page originated from.
(2) When, all remote/pagers and sidekick remotes for that vehicle must be learned at the time of programming.
When you program your remote at the second vehicle, that vehicle’s original remote must also be
programmed. Your remote should be set in Vehicle “2” and the vehicle’s original remote should be set in
Vehicle “1”.
LCD REMOTE
SIDEKICK REMOTE
VEHICLE 1 = 1 - 1
VEHICLE 2 = 2 - 1
VEHICLE 1 = BLUE LED
VEHICLE 2 = RED LED
VEH 1 / VEH 2
VEHICLE
ICON
VEH 1 / VEH 2
Push 2 Seconds
to change from
Vehicle 1 to 2
VEH
CLOCK SET
Push 2 Seconds
to change from
Vehicle 1 to 2
Push VEH Button 5
Times to set Clock
Note: Use can use Vehicle 2 Mode to turn off remote if there is no system installed in a 2nd vehicle
21
2-Way Data Port
Most new vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry
Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or
Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port
Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote
Starter and the bypass interface module.
Features Include
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Transponder Immobilizer.
PassLock Immobilizer.
O.E.M. Alarm Control.
R.A.P. Shutdown.
Power Door Locks.
Priority Unlock.
Sliding Doors.
Trunk Release.
Parking Lights.
Courtesy Lights.
Tachometer.
Heated Seats.
Rear Defrost.
Driver 1 and 2 Memory presets.
The actual features controlled depend on the vehicle and Databus module.
22
23
Crimestopper Security Products Inc.
1770 So. Tapo Street
Simi Valley, CA 93063
(800) 998-6880
www.crimestopper.com
©2012 Crimestopper Security Products
ONLINE TECHNICAL SUPPORT
www.crimestopper.com
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising