The table saw is one of the most commonly used stationary power

The table saw is one of the most commonly used stationary power
Table Saw Safety
Table Saw
1. Wear safety glasses, goggles or a face shield at all times while using the saw.
2. If the cutting operation is dusty, wear a dust mask.
3. Do not wear gloves while operating a table saw.
4. Avoid long sleeves, ties, dangling jewelry or any other loose fitting clothing while
operating a table saw. The clothing could get caught in the blade.
5. Wear non-slip footwear.
6. Use a push stick to cut stock that is 150 cm or less in width.
7. Use a stop block when you crosscut short lengths.
8. Position your body so that it is NOT in line with the blade. This is to avoid being
injured by flying sawdust, woodchips or the work.
9. The height of the blade should be set just slightly higher than the stock being cut.
It should never be more than 6mm above the height of the stock. This is to ensure
that if your hand slip you only receive a slight cut and do not lose a limb.
10. Always stand firmly on the floor and avoid any awkward operations. This is to
avoid falling into the blade by slipping or losing your balance.
11. Do not carry on a conversation while cutting. Pay attention to the work being
performed.
12. Do not reach behind or over the blade unless it has stopped turning.
13. Do not leave the saw until the blade has come to a complete stop.
14. Always disconnect the power prior to changing the blade or performing any other
maintenance operation.
15. Make sure that the blade has stopped turning before you adjust the table saw.
16. After any adjustment, make sure that the blade is free before you turn on the
power.
17. Ensure that the guides are positioned properly and that the tabletop is smooth and
polished. An unclean or rough table requires you to use more force to push the
stock through the blade. The more force that you are required to use the more
chance that you may slip or lose your balance.
18. Maintain the rip fence parallel to the blade so the stock will not bind on the blade
and be thrown.
19. Check the throat plate to ensure that it fits exactly and has a slot just slightly
larger that the blade. Never operate a table saw with the throat plate removed
20. Do not make free-hand cuts on the table saw. The stock must be guided through
the blade either by the rip fence or the miter gauge.
21. Keep the blades' guards, spreaders and ant kickback devices in place and
operating properly. The spreader must be in alignment with the blade and the ant
kickback device must be in place and operating properly. Their action must be
checked before cutting.
22. Only seasoned, dry, flat wood should be cut.
23. Work should be released only when it has gone past the blade.
o
Whenever the stock is lifted or tilted above the surface of the table, the
saw can shake the stock, causing you to lose your grip.
o
Losing your grip on a piece means that your hand can slip toward the saw
blade or the work can be forcefully kicked back towards you.
24. Check that the stock has no nails, knots screw, stones etc. in it prior to cutting into
the wood. These items can become projectiles and cause injury.
25. Do not use the fence and a miter gauge at the same time, unless they are both on
the same side of the fence.
26. A circular table saw should be guarded with a hood (crown guard) that completely
covers the blade projecting above the table. The guard should ride the thickness of
the stock being cut, adjusting to the thickness of the stock.
27. The fence must not be adjusted while the saw is running.
28. While long stock is sometimes crosscut on a table saw, it is not a good practice.
The long stock may interfere with other operations and may be a hazard to other
workers or equipment. It is also difficult to support and is better cut on a swing
saw, pull saw or radial arm saw.
Safe Ripping Procedure
1. Wear safety glasses, goggles or a face shield at all times while using the saw.
2. If the cutting operation is dusty, wear a dust mask.
3. Do not wear gloves while operating a table saw.
4. Avoid long sleeves, ties, dangling jewelry or any other loose fitting clothing while
operating a table saw. The clothing could get caught in the blade.
5. Wear non-slip footwear.
6. Maintain the rip fence parallel to the blade so the stock will not bind on the blade
and be thrown.
7. Keep the blade sharp. Replace or sharpen ant kickback devices when the points
become dull.
8. Keep the blades guards, spreaders and ant kickback devices in place an operating
properly. The spreader must be in alignment with the blade and the ant kickback
device must be in place and operating properly.
9. Cut material that is seasoned, dry and flat.
10. Release work only when it has been pushed completely past the blade.
11. When the width of the rip is 6 inches or wider, use your right hand to feed the
work piece until it is clear of the table. Only use the left hand to guide the work
piece - do not feed the work piece with the left hand.
12. When the width of the rip is less than 2 inches, the push stick cannot be used
because the guard will interfere. Use the auxiliary fence-work support and push
block. Use the two C clamps to attach the auxiliary work-fence support the rip
fence.
13. When the width of the rip is 2 to 6 inches, use the push stick to feed the work.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement