Owner’s Manual
With Assembly Instructions
For Model CC-LUV01B
&
Model CC-LUV01A
(Silver Edition)
www.luvcart.com
Please read this manual carefully and save it with your original sales receipt
Tools needed for assembly: Phillips screwdriver, 7/16” wrench, adjustable wrench and safety scissors (tools not included)
Use only with 12 Volt lead-acid rechargeable battery and 12 volt charger (both included).
Copyright © 2002-2004 by The CartCraft Company
All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information storage and retrieval system, without permission in writing from the copyright owner.
12
Table of Contents
A Important Information ………………………………………………………………............... 2
B Warnings and Cautions ……………………………………………………………................. 3
C Parts …………………………………………………………………………………............... 4
D Assembly ……………………………………………………………………………............... 6
E Battery Charging ……………………………………………………………………............... 10
F Battery Care and Disposal ……………………………………………………………………. 11
G How to Operate ……………………………………………………………………................. 12
H Caring for Your Vehicle ……………………………………………………………………… 13
I Problems and Solutions ……………………………………………………………................. 14
J Limited Warranty …………………………………………………………………….............. 16
Important Information
A
•
Your new LUVcart requires some assembly.
•
Read this manual carefully for important safety information and operating instructions before using your LUVcart. Keep these instructions for future reference as they contain important information.
•
This vehicle is designed for residential use: performance may vary depending on weight of load, slope of terrain and texture of driving surface.
•
To prevent damaging the motors and gears, do not tow anything behind the LUVcart or overload it. Do not exceed the maximum weight capacity of 200 lbs. (90 kg).
•
If you have any questions about your LUVcart, please call our toll-free service lines at 1-866-
LUV-CART (588-2278) from 9 AM to 5 PM (EST) Monday through Friday. Trained customer service representatives are available to take your call.
•
Please complete and return the enclosed Registration Card or log-in to our website www.luvcart.com
and fill out the registration form online.
IMPORTANT INFORMATION REGARDING BATTERY CARE
NEVER ALLOW THE BATTERY TO COMPLETELY DISCHARGE BEFORE CHARGING.
CHARGE THE BATTERY BEFORE STORING VEHICLE. DO NOT LEAVE YOUR
BATTERY IN THE STATE OF DISCHARGE, THIS WILL RUIN THE BATTERY.
REMOVE THE BATTERY DOOR AND TAKE BATTERY OUT OF DRIVETRAIN BEFORE
BEGINNING ASSEMBLY. USE CAUTION THE BATTERY IS HEAVY.
DO NOT PULL VEHICLE BACKWARDS WHILE OPERATING IN FORWARD UNDER
POWER. THIS CAN DAMAGE THE MOTOR AND DESTROY THE GEARS.
2
B
Warnings and Cautions
ELECTRICAL HAZARD
WARNING
•
PREVENT FIRE
-
Never modify the electrical system. Alterations could cause a fire resulting in serious injury.
-
Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury.
-
Use of components in the product other than those supplied could cause overheating, fire or explosion.
•
The battery must be handled by adults only. The battery is heavy and contains sulfuric acid
(electrolyte). Dropping the battery could result in serious injury.
•
Never allow children to charge the battery. A child could be injured by the electricity involved in charging the battery.
•
Never lift or carry the battery by the wires or connector. This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.
•
Read the safety instructions on the battery.
•
Examine the charger and the connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
OPERATING HAZARD
WARNING
•
Never carry passengers
•
Do not exceed maximum recommended load of 200 lbs. (90 kg.)
•
Overloading may be dangerous and cause permanent damage to vehicle
•
Always disperse load evenly in the bucket
•
Always check for objects in vehicles path before moving
•
DO NOT park vehicle on hills or steep slopes
CAUTION
•
Keep vehicle under power when proceeding down inclines. Motor friction will help operator better control load.
3
Parts
C
•
If you experience a problem with this product, or are missing a part, please call us at 1-
866-LUV-CART (588-2278), rather than return this product to the store.
•
Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
UPPER BUCKET LOWER BUCKET DRIVETRAIN
FRONT WHEEL (2) REAR CASTER WHEEL UPPER HANDLE
TOP TOOL TRAY TOP TOOL TRAY
(model CC-LUV01B) (model CC-LUV01A)
(Silver Edition)
BATTERY DOOR BATTERY RECHARGER
(ships attached to drivetrain)
4
BATTERY
10”
Wheel Bolt (2)
CONTENTS OF LARGE HARDWARE BAG
Hardware is packed in smaller separate colored bags to correspond to specific assembly steps – see chart below
(indicates total quantity)
*items not drawn to scale*
¼” x 1 ¾” Screw (4) ¼” x 1 ½” Screw (6) ¼” x 1” Screw (4) ¼” x ½” Screw (6)
¼”-Nyloc Nut (6) ¼” Lock Washer (8) ¼” Small Flat Washer (10) ¼” Large Flat Washer (4)
Tie Wrap (3)
CONTENTS OF SMALLER HARDWARE BAGS
Small Bag Color
Blue
Assembly Steps
1
Assembly Description
Upper & lower bucket
Green
Clear
Red
2
3
6
7
9
Drivetrain to lower bucket
Rear Caster
Upper handle to lower handle
Tray to upper handle
Secure wire harness to tubing
Hardware
¼” x ½” Screw
¼” Lock Washer
¼” Small Flat Washer
¼” x 1 ½” Screw
¼” Lock Washer
¼” Large Flat Washer
¼” x 1” Screw
¼” Small Flat Washer
¼” x 1 ½” Screw
¼” Nyloc nut
¼” Small Flat Washer
¼” x 1 ¾” Screw
¼” Nyloc nut
Tie wrap
Quantity
6
4
4
4
4
4
4
4
4
3
2
2
2
4
5
1
D rear of bucket
Assembly
2
rear mounting plate
•
Place upper bucket face down on large, clean, flat surface. Face down would be with the stake knock outs and round handle holes closest to the ground.
•
Position lower bucket in channel along rim of upper bucket. The lower handle assembly attached to the lower bucket should be positioned over the round handle holes in the rear of the upper bucket.
Hint: Before inserting screws make certain that all the threaded inserts are seated in the receiving holes of the lower bucket. This may require that you visual line up the inserts.
•
From the blue hardware bag, insert a ¼” x
½” screw through each of the holes in the rim of the lower bucket, as shown in diagram 1.
•
Tighten the screws with a Phillips screwdriver. Do not over-tighten.
Hint: Do not press down too hard on screw while tightening; this may cause the threaded insert to dislodge from locked position and spin freely. If insert does dislodge push back into recessed locked position on the inside of the bucket assembly and continue to tighten.
6
REMOVE BATTERY DOOR AND TAKE
BATTERY OUT OF DRIVETRAIN BEFORE
ATTEMPTING NEXT STEP
•
Place complete drivetrain assembly on lower bucket with battery door opening and wire harness facing towards rear mounting plate attached to lower handle assembly.
Make certain wire harness is clear before lowering. Do not place drivetrain on top of wire harness.
•
Line up holes in drivetrain with receiving holes in lower bucket.
Hint: Drivetrain has a specific position on the lower bucket; make certain drivetrain is
“seated” properly before inserting screws.
•
From the green hardware bag, first place a
¼” lock washer and then a ¼” small flat washer on a ¼” x 1 ½” screw. Insert screws through each of the holes, as shown in diagram 2.
Note: Threaded inserts are used again, no nut required.
3
2
•
From the clear hardware bag, first place a
¼” lock washer and then a ¼” large flat washer on a ¼” x 1” screw. Insert screws through each of the holes, as shown in diagram 3 and tighten.
4
1
outside of the drivetrain.
•
Take front wheel and slide the side marked
INSIDE onto the drivetrain making certain to engage the slots in the drivetrain with the spokes of the wheel rim, as shown in diagram 3-A.
1
•
Remove the cardboard protective covering on the slotted portion of the gearbox on the
3-A
2
•
Insert 10” wheel bolt through the wheel bearing and into the drivetrain, as shown in diagram 3.
•
Tighten with an adjustable wrench.
Note: Do not attempt to over tighten the wheel bolt axel. Wheel assembly was designed to have a slight bit of “play” in it when it is securely fastened.
•
Repeat procedure on the other side of the vehicle.
•
Position the rear caster wheel over the receiving holes in rear mounting plate on the lower bucket.
•
Place battery in battery opening with (+) and (-) terminals facing down and outwards towards the opening, as shown above.
•
Battery should be inserted with the (+) terminal closest to the wire connector with red casing and the (-) terminal closest to the wire connector with black casing.
•
Slide the battery wire connector onto the
red battery connector of the same color as indicated in diagram 4-A.
•
Repeat same procedure on battery terminal marked (-) and wire connector with black casing.
4-A
Note: Make certain that the battery connectors are firmly attached before moving onto next step.
7
5
6
5-A
•
With the square block on the rear of the battery door towards the battery and the screw holes facing down, hook tab of battery door on lip of battery opening at a slight angle.
Hint: The engraving on the battery door should be upside down during this step.
•
Close the battery door over opening.
•
Insert ¼” x 1” screws, previously attached, through each hole in battery door.
•
Tighten with Phillips screwdriver.
•
Turn the complete bucket assembly over onto its wheels.
Note: Use caution in completing this task.
LUVcart is large and heavy. Make certain the wire harness is clear and will not be damaged in the process.
Hint: The easiest way to turn LUVcart over is to grab the lower handle assembly along with the wire harness and bring the rear caster up over the drivetrain, onto the bucket face and down on the front wheels.
8
•
Take the complete upper handle assembly and slide the tubes through the handle holes in the upper bucket. The upper handle tubes should slide over the lower handle tubes attached to the lower bucket.
•
From the red hardware bag, insert a ¼” x
1 ½” screw from the outer portion of the handle, as indicated in diagram 6, passing through the screw hole were the upper and lower handle attach.
•
Once the screw is completely through the handle assembly, first place a ¼” flat washer on the screw and then ¼” Nyloc nut on the inserted screw.
•
Tighten with 7/16” wrench, repeat.
7
•
With the upper handle assembly positioned as indicated in the diagram 7, place the top tool tray on the upper handle lining up the holes in the tray with the holes in the handle.
•
From the red hardware bag, insert ¼” x
1 ¾” screw through each hole of the top tool tray passing through the handle assembly and out the back of the handle.
•
Once the screws are completely through the upper handle, first place a ¼” small washer and then a ¼” Nyloc nut on the screws.
•
Tighten with a 7/16” wrench.
8
•
Tilt the entire assembled LUVcart forward onto its front bucket face.
•
Take the wire harness cable and run it up along the right side handle tubing.
•
Plug the connector end of the wire harness coming from the drivetrain into the connector that is secured underneath the top tool tray, as indicated in diagram 8.
•
Press locking tab securely into position to prevent wire harness from accidentally pulling away from switch connector.
9
•
Return LUVcart to its operating position on all wheels.
•
From the red hardware bag, place the supplied tie wraps around the wire harness cable and handle tubing in the locations indicated in diagram 9. Cut excess tie wrap material, with safety scissors, as desired.
9
E
ELECTRICAL HAZARD
WARNING
•
PREVENT FIRE
-
Never modify the electrical system.
Alterations could cause a fire resulting in serious injury and could also ruin the electrical system.
-
Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury.
-
Use of components in the product other than those supplied could cause overheating, fire or explosion.
•
The battery must be handled by adults only. The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injury.
•
Never allow children to charge the battery. A child could be injured by the electricity involved in charging the battery.
•
Never lift or carry the battery by the wires or connector. This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.
•
Read the safety instructions on the battery.
•
Examine the charger and the connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
CAUTION
Battery Charging
Use the charger in dry locations only.
About Automatic Fuse
Your LUVcart is equipped with a built-in resetting fuse. The fuse is a self-resetting safety device that automatically “trips” and shuts down operation of LUVcart if LUVcart is overloaded or the operating conditions too severe. Once a fuse has “tripped”, it will automatically reset itself after approximately 5 seconds and allow LUVcart to resume normal operations. To avoid repeated automatic shutdowns, do not overload LUVcart by exceeding the 200 lb. (90 kg) maximum load capacity. Avoid severe operating conditions, such as driving up very steep slopes or extremely loose or muddy terrain, which can cause the wheels to stop spinning while power is still being supplied to the motors.
USE CAUTION WHEN PROCEEDING UP STEEP
INCLINES OR USING IN SEVERE CONDITIONS.
IF AUTOMATIC FUSE DOES “TRIP” LOAD MAY
SUDDENLY COME BACK ON OPERATOR
CAUSING INJURY.
If the fuse continually trips under normal operating conditions, please contact us at
1-866-LUV-CART (588-2278).
Important
•
You do not need to remove the battery from your LUVcart to recharge it.
•
Do not short circuit the battery.
•
Use only the 12 volt charger supplied to charge your LUVcart rechargeable 12 volt battery.
•
If your battery is old and will not accept a charge, do not leave it in LUVcart.
•
Always remove a dead battery from
LUVcart.
10
Battery Charging
Charger
Connector
•
Plug the charger into a standard wall outlet.
•
Plug the charger connector into the charger receptacle on the right side of the top tool tray.
•
The charging status can be determined by the LED display on the charger (see reverse side of charger for LED information). One light illuminated indicates power is flowing and currently charging. Two lights illuminated indicates the unit is full charged.
•
Recharge the battery for at least 8 hours after each use of your LUVcart, or until the charger indicates, fully charged (two lights).
•
Once the battery is charged, pull on the charger connector to disconnect it from the charger receptacle on top tool tray.
F
Battery Care
and Disposal
Care
If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. See information below for proper disposal.
If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician. If acid is internally ingested call a physician immediately.
•
Recharge the battery after each use.
•
Do not allow the battery to run down completely before charging.
•
Charge the battery before storing the
LUVcart.
•
Charge the battery at least once per month, even if the LUVcart has not been used.
•
Leaving the battery in a discharged condition will cause battery damage.
•
Do not store the battery in temperatures above 85°F(23°C) or below -10°F(-23°C).
•
Examine the battery, charger and its connector for excessive wear or damage each time you charge the battery. If damage is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
•
You may leave your LUVcart plugged in and charging for extended period of time.
Disposal
•
Your LUVcart battery is a sealed lead-acid battery. It must be recycled or disposed of in an environmentally sound manner.
•
Do not dispose of a lead-acid battery in a fire. The battery may explode or leak.
•
Do not dispose of a lead-acid battery in your regular, household trash. The incineration, landfilling or mixing of sealed lead-acid batteries with household trash is prohibited by law in most areas.
•
Return exhausted batteries to a federal or state approved lead-acid battery recycler or
CartCraft. Contact your local waste management officials for other information regarding the environmentally sound collection, recycling and disposal of leadacid batteries.
11
12
How to Operate Your LUVcart
G
OPERATING HAZARD
WARNING
•
Never carry passengers
•
Do not exceed maximum recommended load of 200lbs. (90kg.)
•
Overloading may be dangerous and cause permanent damage to vehicle
•
Always disperse load evenly in the bucket
•
Always check for objects in vehicles path before moving
•
DO NOT park vehicle on hills or steep slopes
Model CC-LUV01B
LUVcart (model CC-LUV01B) is set to operate at maximum of 2 mph in a forward direction only.
•
In order to move forward, press down on the PowerPad integrated into the top tool tray.
•
Operator is responsible for steering and controlling LUVcart. Use the handle grip to steer the
LUVcart in the direction you wish to go.
•
To stop, release the PowerPad
Note: LUVcart is not equipped with a braking system. When the PowerPad is released to stop,
LUVcart may continue to advance due to momentum. Do not let go of handle grip until LUVcart comes to a complete stop.
Handle Grip
PowerPad™
Model CC-LUV01A (Silver Edition) ONLY
•
LUVcart Silver Edition (model CC-LUV01B) is equipped with 2-forward speeds (fast & slow) and
1-reverse speed.
•
To operate in forward, set the direction / speed switch in the position of the speed you desire -
Fast Forward , switch completely depressed forward or Forward , switch set in middle position. Once you have selected a speed press down on the PowerPad to engage operation.
To stop, release the PowerPad.
•
To operate in reverse: 1) set direction switch in Reverse switch completely depressed backward 2) press and hold down safety button on the top tray (you must keep the safety button continually depressed to operate in reverse) and 3) press down on the PowerPad integrated into the top tool tray. To stop, release the PowerPad. For safety, once either the safety button or PowerPad is released the LUVcart will stop.
Note: To avoid damage to the gears make certain LUVcart is completely stopped before changing directions.
•
Operator is responsible for steering and controlling the LUVcart. Use the handle grip to steer the
LUVcart in the direction you wish to go.
1
Set direction switch in reverse
(switch completely depressed backwards)
2
Press and hold down safety button
(make certain to keep button depressed or vehicle will stop)
3
Press down PowerPad™
H
Caring for Your LUVcart
•
Check all screws and nuts regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces.
•
Periodically check the tire pressure in your LUVcart tires. The recommended tire pressure is 28 psi. Maximum is 30 psi. DO NOT OVERINFLATE THE TIRES. If you over-inflate your tires, you could cause it to explode resulting in severe injury. LUVcart tire valves work like bicycle tires.
To add air, remove the cap and push the air hose or pump fitting onto the end of the valve stem. To remove air, depress the pin in the center of the valve stem.
•
During snowy or rainy weather, your LUVcart should be stored inside or under a protective cover, such as the LUVcart Soft Cover. Remember to charge the battery at least once per month while your LUVcart is not in regular use.
•
Avoid operating your LUVcart in wet or snowy conditions and do not spray the electrical areas of the LUVcart with a hose. Water or moisture in the motors or electrical switches can cause them to corrode and could cause switch or motor failure.
•
LUVcart may be hosed off using extra care to avoid water being sprayed directly on top tool tray or through the battery door.
13
Problems and Solutions Guide
I
IMPORTANT! If you experience a problem with your LUVcart, first check the Problems and
Solutions Guide below. If you still experience a problem, please check our website for product updates
( www.luvcart.com
) or call us toll-free 1-866-LUV-CART (588-2278) between 9 AM and 5 PM (EST)
Monday through Friday.
Problem
Possible Cause Solution
Vehicle does not run Undercharged battery Recharge the battery after each use.
Check all connectors. Make sure that charger connector is properly plugged in and that the charger is plugged into the wall.
Vehicle was running but suddenly stopped
Charger is not working
Tripped fuse
Make sure power flow to the wall outlet is “ON”.
There is no sure way to tell if your charger is working unless you have a volt meter. If you suspect there is a problem with your charger, contact us at 1-866-588-2278.
Each LUVcart has a built-in fuse. A fuse may “trip” and shut down operation of the vehicle if the vehicle is overloaded or the conditions too severe. The fuse will automatically reset itself after approximately 5 seconds, allowing the vehicle to resume normal operation. To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 200 lb. maximum weight capacity. Do not drive up extremely steep hills or run into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. If the fuse continually trip under normal working conditions, contact us at 1-866-588-2278.
Loose wire or loose connectors Check all wires and connectors. Make sure the battery connectors are secure and the control plug connection is snug.
Dead battery If your battery is old or if you have not followed Battery Care instructions, your battery may be dead. If you are unsure whether or not the battery is dead, you can have it tested at a local battery supplier.
Electrical switch damage The electrical switches can become corroded due to exposure to water or moisture, or can wear down after extensive use. Contact us at 1-866-588-2278 for diagnosis and repair.
Motor damage Contact us toll free at 1-866-588-2278 for diagnosis and repair.
Loose wire or loose connectors Check all wires and connectors. Make sure the battery connectors are secure and the control plug connection is snug.
Tripped fuse Each LUVcart has a built-in fuse. A fuse may “trip” and shut down operation of the vehicle if the vehicle is overloaded or the conditions too severe. The fuse will automatically reset itself after approximately 5 seconds, allowing the vehicle to resume normal operation. To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 200 lb. (90kg) maximum weight capacity. Do not drive up extremely steep hills or run into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. If the fuse continually trip under normal working conditions, contact us at 1-866-588-2278.
14
Problems and Solutions Guide
Problem
Short run time (less than 1 hour of continuous use)
Possible Cause
Undercharged battery
Solution
Recharge the battery after each use.
Vehicle runs sluggishly
Battery is old and will not accept full charge
Tripped fuse
Undercharged battery
Battery needs charging
Battery is old and will not accept full charge
Conditions are too stressful
Check all connectors. Make sure that charger connector is properly plugged in and that the charger is plugged into the wall.
Make sure power flow to the wall outlet is “ON”.
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 6 months to 3 years depending on vehicle use and use conditions. Replace the battery with a new LUVcart 12 volt rechargeable battery. Contact us at 1-866-588-2278.
Each LUVcart has a built-in fuse. A fuse may “trip” and shut down operation of the vehicle if the vehicle is overloaded or the conditions too severe. The fuse will automatically reset itself after approximately 5 seconds, allowing the vehicle to resume normal operation. To avoid repeated automatic shutdowns do not overload the vehicle by exceeding the 200 lb. (90kg.) maximum weight capacity. Do not drive up extremely steep hills or run into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. If the fuse continually trip under normal working conditions, contact us at 1-866-588-2278.
Recharge the battery after each use.
Check all connectors. Make sure that charger connector is properly plugged in and that the charger is plugged into the wall.
Make sure power flow to the wall outlet is “ON”.
After hours of constant use, the battery needs charging.
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 6 months to 3 years depending on vehicle use and use conditions. Replace the battery with a new LUVcart 12 volt rechargeable battery. Contact us at 1-866-588-2278.
The LUVcart is intended for residential use. If slopes are too steep or terrain conditions too inconsistent the LUVcart may experience a noticeable decrease in performance.
Sometimes the vehicle runs, but other times it does not
Loud clacking or grinding noise from a motor-gearbox
Broken gears
Charger gets warm during use It is normal for some chargers to get warm during use and there is no reason for concern.
Battery makes a sizzling or gurgling noise when charging
Loose wire or loose connectors Check all wires and connectors. Make sure the battery connectors are secure and the control plug connection is snug.
Electrical switch damage The electrical switches can become corroded due to exposure to water or moisture, or can wear down after extensive use. Contact us at 1-866-588-2278 for diagnosis and repair.
Contact us at 1-866-588-2278 for diagnosis and repair.
It is normal for some batteries to make noise and swell slightly while charging and there is no reason for concern.
No action required.
If your charger does not get warm during use, it does not mean that it is not working properly.
No action required.
If your battery does not make noise or swell slightly during charging, it does not mean that it is not accepting the charge.
15
Limited Warranty
J
* One year limited warranty from the date of purchase on Model CC-LUV01B
* Two year limited warranty from the date of purchase on Model CC-LUV01A
Six month limited warranty on the 12 volt battery for all models
For the original purchaser, this limited warranty covers the Lawn Utility Vehicle (LUVcart) against defects in materials and workmanship. The six month limited warranty applies only to the 12 volt battery included by The CartCraft Company with the original purchase of the vehicle.
This warranty covers normal use and does not cover the LUVcart or battery if damaged by unreasonable use, neglect, accident, abuse, misuse, improper service or other causes not arising out of defects in materials or workmanship. Evidence of any attempt at consumer repair will void this warranty. This warranty does not cover, and is intended to exclude, any liability on the part of The
CartCraft Company, whether under this warranty or implied by law for any indirect or consequential damages for breach of warranty. Some states do not allow the exclusion or limitation so this limitation may not apply to you.
Should you need service or assistance with your LUVcart during the warranty period, do not return
the vehicle to the store please contact us at 1-866-588-2278.
Please save your original sales receipt.
Contact information
If you have any comments or questions about your LUVcart, or if you’d like to let us know what you think about something or share an idea about how we can improve our product or services, we’d like to hear from you.
Call us:
1-866-LUV-CART
Contact us through our website: www.luvcart.com
Write to us at:
The CartCraft Company
Customer Support
610 Ten Rod Road
North Kingstown, RI 02852
16
