KX-NT556 - Phone Connection
Quick Reference Guide
IP Proprietary Telephone
Model No.
KX-NT551/KX-NT553
KX-NT556
Thank you for purchasing an IP Proprietary Telephone (IP-PT). Please read this
manual carefully before using this product and save this manual for future use. For
more details, please refer to the manuals of the PBX.
This product supports the following PBX versions and CODEC
types:
R
R
R
R
R
KX-NS1000: PCMPR Software File Version 3.0000 or later
KX-NCP500/KX-NCP1000: PBMPR Software File Version 8.0000 or later
KX-TDE100/KX-TDE200: PMMPR Software File Version 8.0000 or later
KX-TDE600: PGMPR Software File Version 8.0000 or later
CODEC: G.722, G.711, G.729A
Note
R In this manual, the suffix of each model number is omitted unless necessary.
R The illustrations may differ from the appearance of the actual product.
Trademarks
R Plantronics is a trademark or registered trademark of Plantronics, Inc.
R All other trademarks identified herein are the property of their respective owners.
Document Version: 2014-01
Important Information
Important Information
FCC and Other Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
R Reorient or relocate the receiving antenna.
R Increase the separation between the equipment and receiver.
R Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
R Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
FCC Declaration of Conformity
Trade Name: Panasonic
Model Number: KX-NT551/KX-NT553/KX-NT556
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza
Newark, NJ 07102–5490 U.S.A.
Telephone No.: 1-800-211-PANA (7262)
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
a. Remain on the line and briefly explain to the dispatcher the reason for the call.
b. Perform such activities in the off-peak hours, such as early morning or late
evenings.
This equipment is hearing aid compatible.
2
Important Information
When you hold the phone to your ear, noise might be heard in your Hearing Aid.
Some Hearing Aids are not adequately shielded from external RF (radio frequency)
energy. If noise occurs, use the speakerphone option (if applicable) when using this
phone. Consult with your audiologist or Hearing Aid manufacturer about the
availability of Hearing Aids which provide adequate shielding to RF energy
commonly emitted by digital devices.
For users in Canada only
R This Class B digital apparatus complies with Canadian ICES-003.
R This product meets the applicable Industry Canada technical specifications.
Compliance with TIA-1083 standard:
Compatible with
Hearing Aid T-Coil
Telephone handsets identified with this
logo have reduced noise and interference
when used with T-Coil equipped hearing
aids and cochlear implants.
T
TIA-1083
3
Accessory Information
Accessory Information
Included Accessories
Handset (1)
Handset Cord (1)
Stand (1)
KX-NT551
KX-NT553/
KX-NT556
Note
For extra orders for the accessories, call toll-free: 1-800-332-5368. (For users in the
United States only)
4
Accessory Information
Optional Accessories
KX-NT551
Wall mount kit
Add-on 48 key module
*1
*2
KX-NT553
KX-NT556
R For users in the United States:
KX-A239 (PQLV206)
R For users in Canada:
KX-A239X (PQLV206)
AC adaptor*1
KX-A432
KX-A433
—
KX-NT505*2
To order an optional AC adaptor, please order using the "KX-A239" or
"KX-A239X" model number (not "PQLV206"). Can also be used with the
KX-NT505.
KX-NT505 has the following accessories.
Stand (1)
*1
Wall mounting
adaptor (1)
Screws for
wall mounting
(3)*1
Screws for
attaching to the unit
(2)
Two screws for attaching the KX-NT505 to a wall.
One screw for attaching the wall mounting adaptor to the unit.
5
Location of Controls
Location of Controls
KX-NT551
KX-NT553
KX-NT556
6
Location of Controls
A Main LCD (Liquid Crystal Display):
KX-NT551: 1 line, KX-NT553: 3 lines, KX-NT556: 6 lines
B Message/Ringer Lamp:
When you receive an intercom call, the lamp flashes green,
and on an outside call, the lamp flashes red. When someone
has left you a message, the lamp stays on red.
C Flexible CO Buttons: Used to seize an outside line or perform
a feature that has been assigned to the key.
D Handset Hook: Keeps the handset stable when the unit is
mounted on a wall.
E Headset Jack
F PAUSE/PROGRAM (KX-NT551 only): Used to insert a pause
when storing a telephone number. This button is also used for
programming this unit.
PAUSE (KX-NT553/KX-NT556 only): Used to insert a pause
when storing a telephone number.
G CONF: Used to establish a multiple party conversation.
H MESSAGE: Used to leave a message waiting indication or call
back the party who left the message waiting indication.
I FLASH/RECALL: Used to disconnect the current call and
make another call without hanging up.
J REDIAL: Used to redial the last dialed number.
K AUTO ANS/MUTE: Used to receive an incoming call in
hands-free mode or mute the microphone/handset during a
conversation.
L TRANSFER: Used to transfer a call to another party.
M AUTO DIAL/STORE: Used for System/Personal Speed Dialing
or storing programme changes.
N HOLD: Used to place a call on hold.
O INTERCOM: Used to make or receive intercom calls.
P SP-PHONE (Speakerphone): Used for performing hands-free
operations.
7
Location of Controls
Q Microphone: Used for hands free conversations.
R Navigator Key: Used to adjust the volume and the display
contrast or select desired items.
S ENTER*1: Used to assign the selected item.
T Soft Buttons (S1-S4)*1: S1-S4 (located from left to right) are
used to select the item displayed on the bottom line of the
display.
U EHS (Electronics Hook Switch) Jack*1
V FWD/DND*1: Used to switch Call Forwarding or Do Not Disturb
on your extension.
W CANCEL*1: Used to cancel the selected item.
X NEXT PAGE*1: Used to switch the page for the Self Labeling
feature.
Y Sub LCD*1: 12 lines
*1
8
KX-NT553/KX-NT556 only
Before Operating the Telephone
Before Operating the Telephone
Speaker volume
While in a hands-free conversation
Press [ ] or [ ] to adjust the volume.
Handset/Headset volume*1
While using the handset or headset
Press [ ] or [ ] to adjust the volume.
Ringer volume
While on-hook or receiving a call
Press [ ] or [ ] to adjust the volume.
LCD Contrast (For main LCD)*2
While on-hook
1. Press the PROG soft button (S1).*3
2. Enter
.
3. Press [ENTER].*4
4. Press [ ] or [ ] to adjust the LCD contrast.
5. Press [ENTER].*4
6. Press [CANCEL].*3
*1
*2
*3
*4
If you hear your own voice through the handset or headset, decrease the
volume.
To change the sub LCD contrast of the KX-NT553/KX-NT556, enter
in
Step 2.
For KX-NT551, press [PAUSE/PROGRAM].
For KX-NT551, press [AUTO DIAL/STORE].
9
Before Operating the Telephone
Ring Tone
1. Press the PROG soft button (S1).*1
2. Press a flexible CO button or [INTERCOM] 2 times.
3. Enter 2 digits (01-30) using the dial keys (0-9), or press [ ] or [ ] to
select the ring tone.
4. Press [ENTER].*2
5. Press [CANCEL].*1
LCD Backlight
While on-hook
1. Press the PROG soft button (S1).*1
.
2. Enter
3. Press [ENTER].*2
4. Press a dial key to select the LCD backlight mode.
: Automatic
: Always ON
: Always OFF
5. Press [ENTER].*2
6. Press [CANCEL].*1
*1
*2
10
For KX-NT551, press [PAUSE/PROGRAM].
For KX-NT551, press [AUTO DIAL/STORE].
Feature Operations
Feature Operations
Making Calls
Calling
MTo an extensionN
1. Go off-hook.
2. Dial an extension number.
MTo an outside partyN
1. Go off-hook.
2. Press a flexible CO button.
3. Dial the outside party’s phone number.
Redial
1. Go off-hook.
2. Press [REDIAL].
Quick Dialing
1. Go off-hook.
2. Dial a quick dialing number.
Doorphone Call
1.
2.
3.
4.
Go off-hook.
.
Enter
Enter a doorphone number (2 digits).
After the confirmation tone, talk.
System Speed Dialing
1. Go off-hook.
2. Enter
.*1
3. Enter a system speed dialing number (3 digits).
*1
You can also press [AUTO DIAL/STORE].
11
Feature Operations
Personal Speed Dialing
MTo storeN
1. Go off-hook.
.
2. Enter
3. Enter a personal speed dialing number (2 digits).
4. Enter the phone number to store (max. 32 digits).*1
5. Press .
6. After the confirmation tone, go on-hook.
MTo dialN
1. Go off-hook.
.*2
2. Enter
3. Enter .
4. Enter a personal speed dialing number (2 digits).
One-touch Dialing
MTo storeN
1. Press the PROG soft button (S1).*3
2. Press a flexible CO button.
3. Enter .
4. Enter the number to store (max. 32 digits).*1
5. Press [ENTER].*4
6. Enter the text to store (max. 12 digits).*5
7. Press [ENTER].*5
8. Press [CANCEL].*3
MTo dialN
1. Go off-hook.
2. Press the flexible CO button assigned as a One-touch Dialing
button.
*1
*2
*3
*4
*5
12
Enter the outside line access number before an outside phone number.
You can also press [AUTO DIAL/STORE].
For KX-NT551, press [PAUSE/PROGRAM].
For KX-NT551, press [AUTO DIAL/STORE].
KX-NT553/KX-NT556 only
Feature Operations
During a Conversation
Call Hold
MTo holdN
1. Press [HOLD].
2. After the confirmation tone, go on-hook.
MTo retrieve a call at the holding extensionN
1. Go off-hook.
2. Press a flexible CO button or [INTERCOM].
MTo retrieve an outside call from another extensionN
1. Go off-hook.
2. Press a flexible CO button.
Call Transfer
MTo an extensionN
1. Press [TRANSFER].
2. After the confirmation tone, dial an extension number.
3. Talk.
4. Go on-hook.
MTo an outside partyN
1. Press [TRANSFER].
2. After the confirmation tone, press a flexible CO button.
3. Dial an outside phone number.
4. Talk.
5. Go on-hook.
13
Feature Operations
Setting the Telephone According to Your Needs
Do Not Disturb
1. Go off-hook.
.
2. Enter
3. Press a dial key to select the setting.
: Both outside and intercom calls
: Outside calls only
: Intercom calls only
4. To enable Do Not Disturb, enter .
To cancel Do Not Disturb, enter .
5. After the confirmation tone, go on-hook.
Timed Reminder
MTo setN
1. Go off-hook.
.
2. Enter
3. Enter the hour and minute (4 digits).
(AM) or
4. If 12-hour-time display is set, enter
5. Enter
(1 time) or
(daily).
6. After the confirmation tone, go on-hook.
MTo cancelN
1. Go off-hook.
.
2. Enter
3. After the confirmation tone, go on-hook.
MTo stop or answer the ring backN
1. Press [INTERCOM], or go off-hook.
14
(PM).
Feature Operations
Useful Features
Multiple Party Conversation
MTo add other parties during a conversationN
1. Press [CONF].
2. After the confirmation tone, dial the phone number of the party to
add.
3. Talk to the new party.
4. Press [CONF].
5. After the confirmation tone, talk with multiple parties.
MTo leave a conferenceN
1. Press [CONF].
2. After the confirmation tone, go on-hook.
Before Leaving Your Desk
Call Forwarding
1. Go off-hook.
.
2. Enter
3. Press a dial key to select the types of calls to apply this feature to.
: Both outside and intercom calls
: Outside calls only
: Intercom calls only
4. Press a dial key to select the status.
: All calls
: Busy
: No answer
: Busy/No answer
: Cancel*1
5. Enter an extension number, and then enter , or enter a CO line
access number, an outside phone number, and then enter .
6. After the confirmation tone, go on-hook.
*1
If you enter
in Step 4, you can skip Step 5.
15
Feature Operations
Self Labeling (KX-NT553/KX-NT556 only)
The KX-NT553/KX-NT556 features 12 flexible buttons, with an LCD screen next to
the buttons. Each item can be named on the LCD screen through personal or
system programming to reflect the function of its corresponding flexible button.
Additionally, the KX-NT553 (KX-NT556) flexible buttons can be organized into 2 (3)
“pages”, allowing you to assign a total of 24 (36) items to the 12 flexible buttons.
You can toggle between pages by pressing [NEXT PAGE], as follows:
レヹノワヵブブピ
CO 12
Bank
CO 11
Home
CO 10
London offc.
CO 09
NY offc.
CO 08
Sales
CO 07
Chris Walace
CO 06
Andre Romel
CO 05
Sean Carter
CO 04
Keith Murray
CO 03
Log-in/out
CO 02
LCS
CO 01
CO 13
Storing a One-touch Dialing button, and setting the displayed text
for the Self Labeling LCD
1. Press the PROG soft button (S1).
2. Press a flexible CO button, or press [NEXT PAGE], and then press
a flexible CO button.
3. Enter .
4. Enter the number to store (max. 32 digits).*1
5. Press [ENTER].
6. Enter the text to store (max. 12 digits).
7. Press [ENTER].
8. Press [CANCEL].
*1
16
Enter the outside line access number before an outside phone number.
Installation and Setup
Installation and Setup
Note
R Panasonic assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
Attaching a KX-NT505 to the KX-NT553/KX-NT556
The KX-NT505 allows 48 additional flexible CO buttons to
be added to this unit. These buttons are used to seize an
outside line, make a call using One-touch Dialing, or
perform a feature that has been assigned to the key.
1. Open the flat cable cover of
your unit.
2. Attach the KX-NT505 to your
unit with the 2 screws*1.
3. Plug the flat cable into the
connector (A), then bend the
cable slightly as shown (B).
4. Close the cover.
*1
Included with the KX-NT505.
17
Installation and Setup
CAUTION
R Before you install or uninstall the Add-on 48 key module, turn off the unit by
disconnecting the AC adaptor (if connected) and the Ethernet cable connected
to the switching hub.
Note
R Up to 4 Add-on 48 key modules can be connected. If 2 or more key modules are
connected, an AC adaptor must be connected to the second key module. If only
1 key module is connected, an AC adaptor is not required.
R Use only the Panasonic AC adaptor. See “Optional Accessories”, Page 5.
Attaching the Stand
KX-NT551
1
2
Insert the catches of the stand into the hooks located in the unit.
Gently push the stand in the direction indicated until it locks into
place. The stand will be mounted.
KX-NT553/KX-NT556/KX-NT505
1
2
Insert the catches (1) of the stand into hooks located in the unit.
Gently push the stand in the direction indicated until it locks into
place. The stand will be mounted in the high position.
Example: KX-NT556
A
18
Installation and Setup
Removing the Stand
KX-NT551
1
Remove the stand in the
direction indicated while
pushing the catches of the
stand with both hands as
shown.
KX-NT553/KX-NT556/KX-NT505
1
Hold the stand with both
hands.
2
Gently rotate the stand in
the direction indicated
until it is released.
Example: KX-NT556
19
Installation and Setup
Connections
KX-NT551
Optional AC adaptor
To a Switching Hub
To a PC
Ethernet cables
To a handset jack
(handset)
Clamp
AC adaptor
LAN
PC
Handset
Headset jack
Optional AC adaptor
To a switching hub
To a PC
Ethernet cables
To a handset jack
(handset)
Clamp
AC adaptor
Handset
Headset
EHS jack
Headset jack
20
Installation and Setup
Note
R When connecting a headset, the following headsets can be used with this unit.
(Not all operations with the headsets can be guaranteed.)
– Wired headsets
Panasonic KX-TCA400 or KX-TCA430
– EHS headsets (KX-NT553/KX-NT556 only)
Selected Plantronics®-brand headsets
For up-to-date information about headsets that have been tested with this unit,
refer to the following web sites:
http://panasonic.net/pcc/support/pbx/
When selecting Ethernet cables (not included)
R Use flexible cables without jack covers. Do not use cables with a hard coating
that may tear or crack when bent.
To prevent damage to the cables, use cables that do not protrude from the
bottom of the base.
Connect the cables as shown in the following illustration.
Incorrect
Correct
Ethernet cable
Ethernet cable
60 mm (2 3/8 in)
or less
R Use a straight CAT 5e (or higher) Ethernet cable (not included) that is 6.5 mm
(1/4 in) in diameter or less.
When connecting to a switching hub
R If PoE is available, an AC adaptor is not needed.
R KX-NT551/KX-NT553/KX-NT556 comply with the PoE Class 3 standard.
When connecting a PC
R The PC port does not support PoE for connected devices.
When connecting cables and the AC adaptor
R Ensure that the Ethernet cables and the AC adaptor cord are clamped to prevent
damage to the connectors.
21
Wall Mounting
Wall Mounting
Note
R When mounting the KX-NT553/KX-NT556 with a KX-NT505 on the wall, attach
the KX-NT505 to the KX-NT553/KX-NT556 first, and then mount them on the
wall. For detail about the attaching, see “Attaching a KX-NT505 to the
KX-NT553/KX-NT556”, Page 17.
R When mounting the KX-NT553/KX-NT556 with a KX-NT505 on a wall, only ONE
KX-NT505 can be attached.
1
Insert the tabs of the wall mounting adaptor into the designated
openings in the base, and then slide the wall mounting adaptor in
the direction of the arrow until it clicks.
KX-NT551
KX-NT553/KX-NT556 with KX-NT505
22
Wall Mounting
2
Fasten the wall mounting adaptor(s) to the base with the screw(s).
(Recommended torque: 0.4 N·m [4.08 kgf·cm/3.54 lbf-in] to 0.6 N·m
[6.12 kgf·cm/5.31 lbf-in])
3
4
Connect the cables to the unit as shown in the illustration below.
Drive the screws into the wall either 83 mm (3 1/4 in) or 100 mm
(3 15/16 in) apart, and mount the unit on the wall.
Example: KX-NT553/KX-NT556 with KX-NT505
3
4
Washer
37
40 mm (1 /64 in)
or less
AC adaptor
Ethernet cables
Drive the screw
to this point.
83 mm
(3 1/4 in)
100 mm
(3 15/16 in)
2
222 m
m
(8 47/
64 in)
23
One screw here
222 mm (8 47/64 in)
One screw here
WALL MOUNTING TEMPLATE
1. Drive the screws into the wall as indicated.
2. Hook the unit onto the screw heads.
/
/
for KX-NT505
83 mm (3 1 4 in)
100 mm (3 15 16 in)
/
/
100 mm (3 15 16 in)
83 mm (3 1 4 in)
for KX-NT551/KX-NT553/KX-NT556
Note:
• If the KX-NT505 is mounted beside a
KX-NT553/KX-NT556, leave
222 mm (8 47/64 in) of space between
the 2 screws for the IP-PT and the 2
screws for the KX-NT505, as indicated
above.
This space is abbreviated in this template
and must be measured.
One screw at either point
One screw at either point
© Panasonic System Networks Co., Ltd. 2014
PNQX6270ZA
PP0114MK0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement