SWS Seceuro Instructs.q4

www.samsondoors.co.uk

0800 328 6250

O pe aiin ra ntte na nc cttiio

SECEUROGLIDE ROLLER GARAGE DOORS,

SECEUROSHIELD, SECEUROSCREEN &

SECEUROVISION ROLLER SHUTTERS www.samsondoors.co.uk

JJuullyy 22000077

IIssssuuee 44

CONTENTS

Page

2

2

1.

General Instructions

2.

Operating Instructions

2.1

Electrically operated products

a) Hold-to-run switches b) Remote control c) Manual override

2.2

Manually operated products

a) Spring operated b) Rod crank c) Swivel belt d) Geared belt

3.

Maintenance

4.

Service and repair record

6

6

7

7

8

8

2

3

6

Date of Installation:

Installation by:

Unique serial number / job ref.:

Item ref. electric* / manual safety devices installed

Contact details:

MK515B0

Safety devices which may be installed: a) Safety brake b) Spring as brake/Double spring c) Safety edge d) Photo cell

*All electrically operated products are powered by a 240V AC motor.

To ensure compliance with the Machinery Directive this document must be given to the owner of the door and held for future reference.

1


0800 328 6250

1. GENERAL INSTRUCTIONS www.samsondoors.co.uk

Your newly-installed product should give you many years of trouble-free service as it is designed to require minimal maintenance and servicing. In order to prolong the life of your door and to reduce the likelihood of problems, please adhere to the following instructions.

Please note all products should only be operated by trained users.

2. OPERATING INSTRUCTIONS

2.1 ELECTRICALLY OPERATED PRODUCTS

Only operate your shutter/garage door when it is in view, making sure it is not obstructed. Ensure, when the curtain is running, that you and any other person stands clear of the curtain and keeps hands etc. away from moving parts.

A) HOLD-TO-RUN SWITCHES

Hold-to-run single pole switch for operating one shutter

Hold-to-run dual pole switch for operating two shutters

Hold-to-run single pole key switch for operating one shutter

• Make sure all windows and doors are closed.

• If your electrically operated shutter contains any manually operated locks these must be disengaged before you operate the shutter. Failure to do so will damage the motor within the shutter.

• Turn/press switch in desired direction. These are momentary switches, therefore operator must be present when opening and closing, with all openings in view.

• It is very important that the motor completes its pre-set rotation, and the motor stops. It is the motor that locks the shutter/garage door, so even though the curtain looks down it may not be locked.

• The motor must stop on its pre-set limits.

Troubleshooting

Fault

The shutter/door fails to operate when the button is pressed/key is turned.

The shutter/door stops before fully opening or closing, or fails to stop when reaching its final open or closed position.

Cause

1. There has been a power failure.

2. The wrong direction is been selected on the control equipment.

3. The thermal trip in the motor may have activated if the door has been operated several times recently.

Solution

1. Wait for power to come back on or operate the shutter/door with the manual override if installed.

2. Select the correct direction.

3. Allow the motor to cool for approximately

30minutes before attempting to operate the shutter/door again.

Contact your installer.

The limits in the motor have failed to operate or may not have been set correctly.

2


0800 328 6250 www.samsondoors.co.uk

2. OPERATING INSTRUCTIONS continued

B) REMOTE CONTROL

Please note the front of the control unit should only be removed by a trained engineer.

Your shutter/garage door can be activated, depending on the type of equipment installed, by pressing and releasing the buttons on the front of the control unit, the buttons on your remote handset, or a separate hold-to-run switch (key, push or turn).

Please note: All products should only be operated when in view; making sure they are not obstructed.

When opening or closing the product door you must monitor the product until it has completed its operation. If the product is fitted with a safety device this could be activated during its operation which would cause the door to stop and reopen a short distance leaving the door partly open.

Hand Transmitters

The transmitters are fitted with four buttons (see diagram) and when any button is pressed the LED illuminates. The typical operating range is approx. 50m (160ft). When the batteries in the transmitters need replacing the LED will flash constantly when any button is pressed. (Batteries are 2 x CR2016 Lithium Cells).

OPEN BUTTON green

STOP BUTTON red

Multi-channel transmitters (Blue) CLOSE BUTTON green

Multi-channel transmitters operate in the same way as the standard hand transmitter but the grey button is used to select the door you wish to operate. The LED on the transmitter will flash to indicate which door you have selected. Press and release the grey button to change the door the hand transmitter will control.

ADD TRANSMITTER

BUTTON grey

STANDARD HAND

TRANSMITTER

(Grey)

Vacation mode / alarm* (*optional extra)

Before you go on holiday you can prevent the door being operated by the buttons on the receiver unit by engaging the vacation / alarm mode once the door is fully closed.

LED

1 2 3

1. Press and hold the stop button.

2. Whilst holding down the stop button press the close button.

3. Release both buttons at the same time.

Activating vacation mode / alarm option

SAFETY DEVICES

1

1. Press and release the open button

Deactivating vacation mode / alarm option

The standard remote control receiver unit is supplied with a safety edge as standard and when required may also be supplied with a photo cell.

Hold-to-run/deadman operation

Your remote control unit may have been supplied without safety devices in hold-to-run (deadman) mode. If this is the case to close the door you will need to press and hold the down button whilst the door is in view ensuring at all times that there are no obstacles in the doorway. To open the door you will need to press and hold the up button whilst the door is in view ensuring at all times that there are no obstacles in the doorway. Please be aware it is possible to set the remote control so that the door will travel in the up direction in the standard automatic mode in which case a single press of the up button will open the door.

Safety edge

The Safety Edge is fitted to the bottom of the door and is activated when the door starts to close. If it comes into contact with an object while the door is closing, it transmits a signal to the wall mounted control unit, the door will then stop and reopen a short distance.

The safety edge also works as a weather seal, designed to be pressed against the ground, to prevent false sensing and reopening it is disabled for the last 50mm of door travel.

If the safety edge hits an obstacle or if you deliberately stop the door you will have four minutes in which you can continue to close the door in the normal way.

To close the door after this four minutes has passed you must either:

1.

Press the up button on the transmitter or the control unit to raise the door to its fully open position. The safety device will automatically reset and the door can now be operated as normal with the safety device active.

2.

Press and hold the down button on the transmitter or control unit to close the door fully. If you release the button the door will stop. Ensure the door has fully lowered and locked before releasing the button. Please note the safety device will not be active until the door returns to its fully open position.

3


0800 328 6250 www.samsondoors.co.uk

2. OPERATING INSTRUCTIONS continued

PHOTO CELL

The PEC projects a pencil line beam across the door opening. If the beam is broken during the closing cycle, the shutter will stop and reopen a short distance.

A visual indication is given on the signal LED as detailed in the System Status Indication section.

If the photo cell beam is broken during the closing cycle the door will stop and reopen a short distance and a visual indication is given on the signal LED. You will now be unable to close the door in the normal way.

To close the door you can either:

1.

Press the up button on the transmitter or the control unit to raise the door to its fully open position. The safety device will automatically reset and the door can now be operated as normal with the safety device active.

2.

Press and hold the down button on the transmitter or control unit to close the door fully. If you release the button the door will stop. Ensure the door has fully lowered and locked before releasing the button. Please note the safety device will not be active until the door returns to its fully open position.

Adding transmitters

• Press and hold down the Grey button on a transmitter that is already loaded onto the control unit.

The lid mounted signal LED will flash YELLOW slowly, keep the button held down until it flashes YELLOW quickly.

• Release the Grey Button.

The lid mounted signal LED will continue to flash YELLOW quickly.

• Press the top green button on the same transmitter once.

The flashing LED will change from flashing YELLOW to flashing GREEN.

• Now press the top green button on the new transmitter once and release.

The flashing LED will change to continuous for 1 second each time it accepts a new transmitter.

• Repeat step 4 for other transmitters to be added on to the system.

Thirty seconds after loading the last transmitter the LED changes to flashing yellow for ten seconds and then returns to normal running mode. Alternatively you can press the top green button of a transmitter that has just been loaded, this will take it straight back to normal running mode.

Note the manufactures code for the transmitter must match the manufacturers code for the receiver, if they do not match, you cannot add that particular transmitter on to the system, the LED will flash RED, GREEN then YELLOW once quickly, if they are not compatible. Please contact your supplier for further details.

Remote Control Trouble Shooting Guide

N.B. Always isolate the power before attempting to make any adjustments or repairs. Untrained operators are advised to contact an approved installer.

System Status Indication

The status of the control unit and/or door is indicated by the lid mounted signal LED. This is a three-colour “RED, YELLOW &

GREEN” lamp (LED) mounted on the front of the control unit, as detailed below:

Door positions

LED signal

GREEN solid

GREEN flashing

RED solid

RED flashing

YELLOW solid

Status open limit activated door opening close limit activated door closing door stationary between the open and close limits

Programming mode (using a transmitter)

LED signal

Slow flashing YELLOW then quick flashing YELLOW

Status control unit in programming mode

4


0800 328 6250

2. OPERATING INSTRUCTIONS continued www.samsondoors.co.uk

SYSTEM STATUS

LED signal/fault

RED rapid flashing

RED flash then two YELLOW flashes

RED flash then three YELLOW flashes

RED flash then four YELLOW flashes

A rapid RED, GREEN then

YELLOW single flash

Long YELLOW then two shorter RED flashes

Reduced operating range

Cause

Photo Electric Cell (PEC) beam broken.

Solution

1. Remove any obstacles which may be in the doorway

(once you have removed the obstacle the signal light will change to solid yellow).

2. Reset the safety device as described in the Photo Cell section.

3. Ensure the photocell and reflector are clean.

4. Re-align the photo cell and reflector (contact your installer).

A motor stall has been detected.

1. Disengage manual locking device.

2. Remove any objects which may have jammed in the guide rails, curtain or roll.

3. Ensure nobody is attempting to ride up on the curtain.

4. Ensure a non-approved item has been attached to the curtain.

5. In extreme conditions the door may have frozen to the guide rails or floor. Try to operate the door again or defrost the frozen section.

The thermal trip has activated on the motor or the motor is not connected.

1. Allow the motor to cool for approximately 30minutes before attempting to operate the door again.

2. The motor may not be connected to the remote control unit contact your installer.

Door overrun time out; the door has been opening or closing for over 60 seconds without detecting a final end limit position.


Indicates that a signal has been received from either a transmitter that has not been loaded on to the system or the transmitters’ manufacturers code does not match with the

SeceuroSmart control unit.

1. Load the transmitter on to the system as per the

“Adding transmitters” section.

2. Contact your installer if the transmitter will not load on to the system.

PEC has failed Self Check test.


Batteries in transmitter are flat or aerials may not be fitted to remote control unit or they may be touching.

1. Transmitter LED does not illuminate when flat and if batteries low it flashes when button pressed. Replace batteries.

2. Ensure aerials are not touching, if aerials are missing then contact your installer.

The door stops

automatically after the bottom edge of the door has passed the top magnet when the door is closing (this only applies when bottom slat safety edge is installed).

•Signal interference.

•Aerials touching or have been removed.

•Top magnet removed from guide rail

A device may be transmitting a strong signal on the same frequency as the remote control so the remote control may have stopped the door to ensure your safety is not compromised. The door will continue to operate once the interfering signal has gone.

Ensure aerials are not touching, if aerials are missing then contact your installer.

The door will not operate if the magnets are missing or are in the wrong position, contact your installer.

To close the door press and hold the down button releasing the button once the door is fully down and locked (ensure the door is fully in view when operating).

5


0800 328 6250


C) POWER FAILURE/MANUAL OVERRIDE (IF FITTED)

In the event of disruption to the power supply, or the motor temporarily over heating (the motor is protected by a thermal cutout), the door can be operated manually. Isolate power supply to shutter before using the manual override.

TO OPERATE:

Hold crank handle in line with eye and rotate handle until the door reaches the open / closed position

.

TO OPERATE:

Externally fitted doors will need the cover cap or override lock removing and the crank handle inserting. Rotate handle until the door reaches the open/closed position.

TO OPERATE:

Remove lock and insert crank handle and rotate until door reaches the open/close position.

Internally installed shutter with internal manual override

Externally installed shutter with external manual override

Internally installed shutter with external manual override

DO NOT OVERWIND

When the main power is reinstated, ensure that the power isolator is switched back on. If applicable secure the handle back onto the wall. Remember to keep the crank handle in a convenient place.

2.2 MANUALLY OPERATED PRODUCTS

Only operate your Shutter when it is in view, making sure it is not obstructed. Ensure, when the curtain is running, that any other person stands clear of the curtain and keep hands etc. away from moving parts.

A) SPRING OPERATED

A spring operated shutter may have a lock in the bottom slat or curtain, shoot bolts in the bottom slat, or pin locks in the guide rails.

Opening the shutter – Press slightly down on the handles when the shutter is in the closed position; disengage the locking mechanism(s). If applicable ensure the key is removed before opening the shutter.

Push the shutter curtain upwards using the handles provided, to open the shutter. Do not let go of the shutter until it has reached its fully open position.

Closing the shutter – Pull the curtain down using the handles provided. When the curtain reaches the closed position, press down on the handles and then engage the locking mechanism(s).

Troubleshooting

Fault

Lock will not engage

Cause

The lock bar(s) is not correctly aligned with the lock hole.

Solution

Apply more pressure to the bottom of the curtain until the lock engages or move the curtain around slightly until it is in the correct position for the lock(s) to engage.

B) ROD CRANK

Lowering the curtain

Make sure all windows and doors are closed. To lower the curtain, pull the crank handle out of the clip and hold the handle at an angle of 45 degrees. This will enable the user to wind the curtain up with ease and also minimise the wear on the crank knuckle. Turn the handle either clockwise or anti-clockwise. If the handle is turned the wrong way it will feel tight. On no account should this be forced as it will result in damage. If it does feel tight simply reverse the rotation of the crank handle.

Once the direction has been identified continue until the curtain is fully down onto the cill or doorstep and continue the rotation until the crank handle feels tight.

This means the curtain is in the locked position.

6


0800 328 6250


RAISING THE CURTAIN

To raise the curtain, pull the crank handle out of the clip and hold the handle at an angle of 45 degrees. This will enable the user to wind the curtain up with ease and also minimise the wear on the crank knuckle. Turn the handle either clockwise or anticlockwise. If the handle is turned the wrong way it will feel tight. On no account should this be forced as it will result in damage. If it does feel tight simply reverse the rotation of the crank handle. Once the direction has been identified turn the handle. The locking mechanism will automatically be disengaged and the curtain will rise up. Do not wind up too fast as this will result in damage to the shutter lid. The buffers will stop on the lid.

C) SWIVEL BELT


Make sure all the windows and doors are closed. Pull the grey webbed belt out of the swivel winder, which will in turn release the curtain down the guide rails. The swivel winder has a brake on it so that the curtain can be stopped anywhere down the guide. This is ideal for blocking out the sun etc. To fully close the curtain, drop the curtain down onto the window cill or doorstep. Pull the tape out about 300mm (12 inches) and place a finger onto the tape where it leaves the swivel winder. Keep the finger in place and release the slack tape. The curtain will then rotate inside the shutter box, engaging the locking mechanism. When the locking mechanism has correctly engaged it should not be possible to manually lift the curtain. The slack tape will then be taken back into the swivel box.

Raising the curtain

To raise the curtain simply pull the tape downwards. This will disengage the locking mechanism automatically. The tape will coil up inside the swivel winder. Again the curtain can be left in any position e.g. halfway up. Physical stops are fitted to the bottom slat to prevent the curtain from lifting out of the guide rails. Do not lift the curtain too fast or vigorously as this may cause damage to the box lid.

Troubleshooting

Fault

Lock mechanism will not engage

Cause

The final 300mm of curtain has not been lowered with sufficient speed to engage the locking mechanism.

Solution

Repeat the process described above for lowering the final 300mm of curtain.

D) GEARED BELT


Make sure all windows and doors are closed. On the geared belt winder box there is a direction of rotation. Put the winder handle into the squared opening and turn the handle in the down direction. The curtain can be stopped anywhere down the guide e.g. halfway down. This is ideal for blocking out the sun etc. Lower the curtain down onto the window cill or doorstep and keep turning until the tape appears to be getting slack. Allow about 300mm (12 inches) of tape to come out of the geared box and then hold the tape at the tape exit of the box. Whilst holding the tape, pull the slack tape downwards and release it. This will rotate the curtain inside the shutter box and engage the locking mechanism. When the locking mechanism has correctly engaged it should not be possible to manually lift the curtain. Any slack tape can be wound back carefully into the geared box.

Raising the curtain

To raise the curtain simply turn the handle in the upwards direction. The locking mechanism will automatically disengage and the curtain will lift up. The curtain can be stopped anywhere in the guides e.g. halfway up. Physical stops are fitted to the bottom slat to prevent the curtain from lifting out of the guide rails. Do not lift the curtain too fast or too vigorously or this may cause damage to the box lid.

Troubleshooting

Fault

Lock mechanism will not engage

Cause

The final 300mm of curtain has not been lowered with sufficient speed to engage the locking mechanism.

Solution

Repeat the process described above for lowering the final 300mm of curtain.

7


0800 328 6250

3. MAINTENANCE www.samsondoors.co.uk

CAREFUL USE OF YOUR SHUTTER/DOOR IS THE BEST WAY TO AVOID MAINTENANCE OR REMEDIAL WORK

Your Shutter/door is low maintenance. The curtain needs wiping with a damp cloth and a mild detergent to remove any excessive dirt/grime to maintain its prime appearance and to reduce the risk of the surface being damaged. This must be done more frequently in a salt air environment.

Marks on the paint finish can be cleaned with many types of car polish. Chips in the paintwork should be touched up to prevent corrosion of the metal.

The power to the shutter should be isolated before washing or repairing the paintwork.

The motor and curtain have been designed to be lubrication free so you must not oil or grease the guide rails. Make sure no foreign items get collected in the guides i.e., stones, sticks, paper etc.

Additional information for electrically operated products

Your door should run smoothly and easily as the motor is not designed to over-come problems of a badly running or damaged door. If necessary contact your approved installer for repair.

The motor should be stopping on the limits and not over-running (indicated by buzzing) when the door hits the floor or the open stops.

N.B. Always isolate the power before attempting to make any adjustments or repairs. Untrained operators are advised to contact an approved installer.

4. SERVICE AND REPAIR RECORD

Date work carried out:

Work carried out:

Work performed by – Sign:

Print:

Company name:




Print:

Company name:



8


Print:

Company name:

This product was manufactured by SWS UK, Hornby Road, Claughton, Lancaster, LA2 9LA

SWS Seceuro Instructs.q4

O pe aiin ra ntte na nc cttiio

JJuullyy 22000077

IIssssuuee 44

General Instructions

Operating Instructions

Electrically operated products

Manually operated products

Maintenance

Service and repair record

1

2

3

4

5

6

7

8

Related manuals

SWS

SeceuroGlide Classic

SWS

SeceuroGlide Manual

SWS

SeceuroGlide Compact

LT60