Lenovo 3000 V200 Hardware Maintenance Manual

Lenovo 3000 V100 and V200
Hardware Maintenance Manual
May 2007
This manual supports:
Lenovo 3000 V100 and V200
(MT 0763 and 0764)
Lenovo 3000 V100 and V200
Hardware Maintenance Manual
Note
Before using this information and the product it supports, be sure to read the general information under “Notices” on page
117.
First Edition (May 2007)
© Copyright Lenovo 2007. All rights reserved.
U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule
contract with Lenovo, if any, or the standard terms of this commercial license, or if the agency is
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in
Data-General, FAR 52.227.14 (Alternate III).
Contents
Introduction . . . . . . . . . . . . . 1
About this manual . . . . . . . . . . .
Important service information . . . . . . .
Strategy for replacing FRUs . . . . . . . .
Strategy for replacing a hard disk drive . . .
Important notice for replacing a system board .
How to use error messages . . . . . . .
Strategy for replacing FRUs for Custom Model
Variant (CMV) products . . . . . . . . .
Using PC Entitlement Warehouse (PEW) . . .
Using eSupport . . . . . . . . . . .
Using the HMM . . . . . . . . . . .
Important information about replacing RoHS
compliant FRUs . . . . . . . . . . . .
Diskette compatibility matrix . . . . . . . .
Safety notices: multilingual translations . . . .
Safety information . . . . . . . . . . .
General safety . . . . . . . . . . .
Electrical safety . . . . . . . . . . .
Safety inspection guide . . . . . . . .
Handling devices that are sensitive to
electrostatic discharge . . . . . . . . .
Grounding requirements . . . . . . . .
Laser compliance statement . . . . . . . .
.
.
.
.
.
.
1
1
1
2
2
2
.
.
.
.
2
3
3
3
. 4
. 5
. 5
. 11
. 11
. 11
. 13
. 14
. 14
. 15
General descriptions . . . . . . . . . 17
Read this first . . . . . . . . . . . .
What to do first . . . . . . . . . . .
Related service information . . . . . . . .
Service Web site . . . . . . . . . . .
Restoring the factory contents by using Product
Recovery discs . . . . . . . . . . .
Passwords . . . . . . . . . . . . .
Power management . . . . . . . . .
Checkout guide . . . . . . . . . . . .
Testing the computer . . . . . . . . .
Detecting system information with PC-Doctor .
Power system checkout . . . . . . . .
.
.
.
.
17
17
19
19
.
.
.
.
.
.
.
19
20
22
24
24
26
26
Lenovo 3000 V100 and V200 . . . . . 29
Product overview . .
Specifications . . .
Status indicators . .
FRU tests . . . .
Fn key combinations
Symptom-to-FRU index
Numeric error codes
Error messages . .
Beep symptoms . .
No-beep symptoms .
© Copyright Lenovo 2007
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
30
30
33
34
35
36
36
38
39
39
LCD-related symptoms . . . . . . . . . 40
Intermittent problems . . . . . . . . . . 41
Undetermined problems . . . . . . . . . 41
FRU replacement notices . . . . . . . . . . 42
Screw notices . . . . . . . . . . . . . 42
Retaining serial numbers . . . . . . . . . 42
Removing and replacing a FRU . . . . . . . . 45
1010 Battery pack . . . . . . . . . . . 46
1020 Hard disk drive slot cover and hard disk
drive . . . . . . . . . . . . . . . 47
1030 DIMM slot cover . . . . . . . . . . 49
1040 DIMM . . . . . . . . . . . . . 49
1050 Backup battery . . . . . . . . . . 50
1060 PCI Express Mini Card slot cover and PCI
Express Mini Card for 802.11 a/b/g wireless
LAN . . . . . . . . . . . . . . . . 51
1070 PCI Express Mini Card slot cover and PCI
Express Mini Card 802.11 a/b/g/n wireless LAN 52
1080 Optical drive . . . . . . . . . . . 55
1090 Middle cover . . . . . . . . . . . 55
1100 Function board . . . . . . . . . . 56
1110 Keyboard . . . . . . . . . . . . 57
1120 Hinge covers, keyboard bezel, 5-1 Digital
Media Reader card, BDC, and fingerprint reader
card . . . . . . . . . . . . . . . . 59
1130 LCD unit . . . . . . . . . . . . 67
1140 Heat sink assembly, CPU, MDC,
ExpressCard slot, and system board . . . . . 70
1150 Fan and base cover (with speakers) . . . . 77
2010 LCD front bezel . . . . . . . . . . 79
2020 Inverter card . . . . . . . . . . . 80
2030 Integrated camera . . . . . . . . . 81
2040 LCD panel, LCD cable, and hinges . . . . 82
2050 Wireless LAN antenna cables . . . . . . 84
Locations . . . . . . . . . . . . . . . 86
Front view. . . . . . . . . . . . . . 86
Rear view . . . . . . . . . . . . . . 87
Bottom view . . . . . . . . . . . . . 87
Parts list . . . . . . . . . . . . . . . 88
Overall . . . . . . . . . . . . . . . 89
LCD FRUs . . . . . . . . . . . . . 101
Keyboard . . . . . . . . . . . . . . 103
Recovery discs . . . . . . . . . . . . 105
Corel software CDs . . . . . . . . . . 114
Miscellaneous parts . . . . . . . . . . 114
AC adapters . . . . . . . . . . . . . 115
Common parts list . . . . . . . . . . . 115
Notices . . . . . . . . . . . . . . . 117
Trademarks . . . . . . . . . . . . . . 118
iii
iv
MT 0763 and 0764
Introduction
About this manual
This manual contains service and reference information for Lenovo 3000 V100 and
V200 (MT 0763 and 0764). Use this manual along with the advanced diagnostic
tests to troubleshoot problems.
The manual is divided into sections as follows:
v The common sections provide general information, guidelines, and safety
information required in servicing computers.
v The product-specific section includes service, reference, and product-specific
parts information.
Important
This manual is intended for trained service personnel who are familiar with
Lenovo 3000 products. Use this manual along with the advanced diagnostic
tests to troubleshoot problems effectively.
Before servicing a Lenovo 3000 product, be sure to review the safety
information under “Safety notices: multilingual translations” on page 5,
“Safety information” on page 11, and “Laser compliance statement” on page
15.
Important service information
Important
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site http://www.lenovo.com/
support
Advise customers to contact the Customer Support Center at 800-426-7378 if
they need assistance in obtaining or installing any software fixes, drivers, and
BIOS downloads.
Customers in Canada should call the Customer Support Center at
800-565-3344 for assistance or download information.
Strategy for replacing FRUs
Before replacing parts
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
© Copyright Lenovo 2007
1
Important service information
v If you are instructed to replace a FRU but the replacement does not correct the
problem, reinstall the original FRU before you continue.
v Some computers have both a processor board and a system board. If you are
instructed to replace either the processor board or the system board, and
replacing one of them does not correct the problem, reinstall that board, and
then replace the other one.
v If an adapter or a device consists of more than one FRU, any of the FRUs may
be the cause of the error. Before replacing the adapter or device, remove the
FRUs, one by one, to see if the symptoms change. Replace only the FRU that
changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have
been customized. Running Automatic Configuration may alter the settings. Note
the current configuration settings (using the View Configuration option); then,
when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as copying,
saving, or formatting. If you select an incorrect drive, data or programs can be
overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling of a system board can cause damage to those components, and may
cause a system malfunction.
Attention: When handling a system board:
v Do not drop a system board or apply any excessive force to it.
v Avoid rough handling of any kind.
v Avoid bending a system board and hard pushing to prevent cracking at each
BGA (Ball Grid Array) chipset.
How to use error messages
Use the error codes displayed on the screen to diagnose failures. If more than one
error code is displayed, begin the diagnosis with the first error code. Whatever
causes the first error code may also cause false error codes. If no error code is
displayed, see whether the error symptom is listed in the Symptom-to-FRU Index
for the computer you are servicing.
Strategy for replacing FRUs for Custom Model Variant (CMV) products
Custom Model Variant (CMV) is a unique configuration that has been negotiated
between LenovoTM and the customer. A unique 4-digit MT and 3-digit model is
provided to the customer to place orders (Example: 1829-W15). A CMV is a special
bid offering. Therefore, it is NOT generally announced.
There are three information resources to identify which FRUs are used to support
CMV products. These sources are PC Entitlement Warehouse (PEW), eSupport, and
the HMM.
2
MT 0763 and 0764
Important service information
Using PC Entitlement Warehouse (PEW)
v PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CMV products at a MT - serial number
level. An example of key commodities are hard disk drives, system boards,
microprocessors, Liquid Crystal Displays (LCDs), and memory.
v Remember, all CMV products are loaded in PEW under the 4-digit MT and
3-digit model, where model = “fixed part number”.
v PEW can be accessed at the following Web site:
http://w3-3.ibm.com/pc/entitle
Customers can also access PEW via
http://www-307.ibm.com/pc/support/site.wss/product.do?template=/
warranty/warranty.vm&sitestyle=lenovo
Click on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input
the MT and the Serial number and the list of key commodities will be returned
in the PEW record under COMPONENT INFORMATION.
v Business Partners using Eclaim will access PEW when performing Entitlement
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key
commodities will be returned in the Eclaim record under SYSTEM DETAILS.
v Authorized IBM® Business Partners can access Eclaim at the following Web site:
https://wca.eclaim.com
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
v eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
v eSupport can be accessed at the following Web site: http://www.lenovo.com/
support
v To view the key commodities, click on PARTS INFORMATION, then PARTS
LOOKUP. Type in the model type and serial number. The key commodities will
be returned in the eSupport record under PARTS SHIPPED WITH YOUR
SYSTEM.
For the Remaining FRUs (the complete list of FRUs at the MT Model level)
v eSupport can be used to view the complete list of FRUs for a machine type and
model.
v To view the complete list of FRUs, type in the machine type and model
(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”
select PARTS INFORMATION. Under “Filter by Category” select SERVICE
PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The
list of service parts by description, with applicable machine type model and FRU
will be displayed.
Using the HMM
Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRUs at the MT Model level. CMVs are custom models and are not found in the
HMM.
Introduction
3
Important service information
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts.
So, if the original FRU parts are non compliant, replacement parts can also be
non compliant. In all cases if the original FRU parts are RoHS compliant the
replacement part must also be RoHS compliant.
Lenovo plans to transition to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo's requirements and
schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The
following statement pertains to these products and any product Lenovo produces
containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS
implementation date, failed RoHS compliant parts must always be replaced using
RoHS compliant FRUs, so only the FRUs identified as compliant in the system
HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or original
part
Replacement FRU
Current or original
part
Replacement FRU
Non-RoHS
Can be Non-RoHS
Must be RoHS
Must be RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
4
MT 0763 and 0764
Diskette compatibility matrix
Diskette compatibility matrix
The compatibility of each of the drives with the diskettes for it is as follows:
Diskette
drive
Diskette
capacity
Compatibility
3.5-inch
1.0 MB
Read and write
2.0 MB
Read and write
4.0 MB
Not compatible
Safety notices: multilingual translations
In this manual, safety notices appear in English with a page number reference to
the appropriate multilingual, translated safety notice found in this section.
The following safety notices are provided in English, French, German, Hebrew,
Italian, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws, springs,
and other small parts are in place and are not left loose inside the computer. Verify this
by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes
can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle,
vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour
ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces
métalliques ou des copeaux de métal pourraient causer un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß
sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im
Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche
geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,
accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella
corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo
l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti
metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los
tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran
sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles
ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.
Introduction
5
Safety notices
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
Dispose of the battery as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an incorrect battery can result in
ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez
pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en
court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.
Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez
à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une
batterie ou une pile inappropriée risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann
geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle
oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die
Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder
Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non
smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle
secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni
locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di
supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di
una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria
stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No
las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
6
MT 0763 and 0764
Safety notices
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw it
into fire or water, or short-circuit it. Dispose of the battery pack as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing when
replacing the battery pack. Use of an incorrect battery can result in ignition or
explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que
les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie
inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei
der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen
der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o
nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,
utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,
ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la
normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al
sustituir la batería. La utilización de una batería no apropiada puede provocar la
ignición o explosión de la misma.
Introduction
7
Safety notices
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,
remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate
it, or expose its cell contents to water. Dispose of the battery as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing. Use of
an incorrect battery can result in ignition or explosion of the battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur
polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,
ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut
conformément à la réglementation en vigueur. Une pile inappropriée risque de
prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt
nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen
für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs
verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare
gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,
riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla
in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive
disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe
determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios, explosiones
o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,
ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de
sus celdas al agua. Deséchela tal como dispone la normativa local.
8
MT 0763 and 0764
Safety notices
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water for at least 15 minutes. Seek
medical care if any symptoms from the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux
ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze
minutes. Consultez un médecin si des symptômes persistent après le lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die
örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas
und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den
Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in
Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15
Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht
werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in
contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua
corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero
permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,
lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.
Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Introduction
9
Safety notices
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise
à la masse d’une batterie peut produire suffisamment de courant pour brûler des
matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto
circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o
provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o
con contacto a tierra puede producir la corriente suficiente como para quemar material
combustible o provocar quemaduras en el personal.
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la
batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der
Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt
wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche
tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di
interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas
de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de
conexión entre dispositivos.
10
MT 0763 and 0764
Safety information
Safety information
The following section presents safety information with which you need to be
familiar before you service a Lenovo 3000 computer.
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any object that
weighs more than 16 kg (35 lb) or that you think is too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, make sure that other service representatives and
the customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your toolcase away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, about 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Attention: Metal objects are good electrical conductors.
v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
v Fan louvers on the machine help to prevent overheating of internal components.
Do not obstruct fan louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
Introduction
11
Safety information
Important
Use only approved tools and test equipment. Some hand tools have handles
covered with a soft material that does not insulate you when working with
live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain
small conductive fibers to decrease electrostatic discharges. Do not use this
type of mat to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine, and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe the
following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from passing
through your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
v
v
v
v
v
12
MT 0763 and 0764
Observe the special safety precautions when you work with very high voltages;
Instructions for these precautions are in the safety sections of maintenance
information. Use extreme care when measuring high voltages.
Regularly inspect and maintain your electrical hand tools for safe operational
condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected from a circuit. First, check that it
has been powered off.
Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
Safety information
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially
unsafe conditions. As each machine was designed and built, required safety items
were installed to protect users and service personnel from injury. This guide
addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-Lenovo 3000 features or options not
covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock)
v Explosive hazards, such as a damaged CRT face or a bulging capacitor
v Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-Lenovo 3000 alterations. Use good judgment as to
the safety of any non-Lenovo 3000 alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.
Introduction
13
Safety information
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.
Note
The use of a grounding system to guard against ESD damage is desirable
but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– When working on a double-insulated or battery-operated system, use an ESD
common ground or reference point. You can use coax or connector-outside
shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
14
MT 0763 and 0764
Laser compliance statement
Laser compliance statement
Some models of Lenovo 3000 computer are equipped from the factory with an
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed, it is
certified in the U.S. to conform to the requirements of the Department of Health
and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J
for Class 1 laser products. Elsewhere, the drive is certified to conform to the
requirements of the International Electrotechnical Commission (IEC) 825 and
CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui
especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage
et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
Introduction
15
Laser compliance statement
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam, do
not view directly with optical instruments, and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in
den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel.
Kerülje a sugárnyalábbal való érintkezést !
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo
direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz
de luz. Evite la exposición directa al haz.
16
MT 0763 and 0764
General descriptions
The descriptions in this chapter apply to any Lenovo 3000 model that has the
PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to
your particular computer.
Read this first
Before you go to the checkout guide, be sure to read this section.
Important notes
v Only certified trained personnel should service the computer.
v Before replacing any FRU, read the entire page on removing and
replacing FRUs.
v When you replace FRUs, use new nylon-coated screws.
v Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might
be overwritten.
v Replace a FRU only with another FRU of the correct model. When you
replace a FRU, make sure that the model of the machine and the FRU part
number are correct by referring to the FRU parts list.
v A FRU should not be replaced because of a single, unreproducible
failure. Single failures can occur for a variety of reasons that have nothing
to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. Consider replacing a FRU only when a
problem recurs. If you suspect that a FRU is defective, clear the error log
and run the test again. If the error does not recur, do not replace the FRU.
v Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
__ 1. Name and phone number of servicer
__ 2. Date of service
__ 3. Date on which the machine failed
__ 4. Date of purchase
__ 5. Failure symptoms, error codes appearing on the display, and beep
symptoms
__ 6. Procedure index and page number in which the failing FRU was detected
__ 7. Failing FRU name and part number
__ 8. Machine type, model number, and serial number
__ 9. Customer’s name and address
Note for warranty:
During the warranty period, the customer may be responsible for repair costs if the
computer damage was caused by misuse, accident, modification, unsuitable
physical or operating environment, or improper maintenance by the customer.
© Copyright Lenovo 2007
17
Read this first
Following is a list of some common items that are not covered under warranty and
some symptoms that might indicate that the system was subjected to stress beyond
normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
v LCD panel cracked from the application of excessive force or from being
dropped
v Scratched (cosmetic) parts
v Distortion, deformation, or discoloration of the cosmetic parts
v Plastic parts, latches, pins, or connectors that have been cracked or broken by
excessive force
v Damage caused by liquid spilled into the system
v Damage caused by the improper insertion of a PC Card or the installation of an
incompatible card
v Improper disc insertion or use of an optical drive
v Diskette drive damage caused by pressure on the diskette drive cover, foreign
material in the drive, or the insertion of a diskette with multiple labels
v Damaged or bent diskette eject button
v Fuses blown by attachment of a nonsupported device
v Forgotten computer password (making the computer unusable)
v Sticky keys caused by spilling a liquid onto the keyboard
v Use of an incorrect ac adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
v Missing parts might be a symptom of unauthorized service or modification.
v If the spindle of a hard disk drive becomes noisy, it may have been subjected to
excessive force, or dropped.
18
MT 0763 and 0764
Related service information
Related service information
This section provides information about the following:
v “Service Web site”
v “Restoring the factory contents by using Product Recovery discs”
v “Passwords” on page 20
v “Power management” on page 22
Service Web site
When the latest maintenance diskette and the system program service diskette
become available, they will be posted on http://www.lenovo.com/spm
Restoring the factory contents by using Product Recovery
discs
When the hard disk drive is replaced because of a failure, no Product Recovery
program is on the new hard disk. In this case, you must use the recovery disc for
the computer. Order the recovery disc and the hard disk drive at the same time so
that you can recover the new hard disk drive with the preinstalled software when
they arrive. For information on which disc to order, see “Recovery discs” on page
105.
To install the factory contents by using Product Recovery discs, do the following:
Note
The recovery process might take up to 2 hours.
1. Make the optical drive the first start up device in the startup sequence.
2. Insert the bootable Rescue and Recovery™ Startup disc into the optical drive,
and then start the computer.
3. In the Rescue and Recovery workspace, complete the following procedure:
a. When the Rescue and Recovery workspace opens, click Continue on the
Welcome window and then click Restore your system.
b. When a message about accessing a USB device is displayed, click OK.
c. In the initial window of the ″Restore your system″ wizard, select Restore
my hard drive to the original factory state and click Next.
d. In the next window, select I do not want to save any files and click Next.
e. A warning opens not to turn off the computer during the recovery process.
Click OK.
4. When the Product Recovery window opens, click OK.
5. The Terms and Conditions window opens, select I accept these terms and
conditions and then click OK.
6. After the files necessary for the product recovery are copied from the Rescue
and Recovery Startup disc to the hard drive, the system restarts automatically
and boot back into Rescue and Recovery. Remove the disc and turn off the
computer.
7. Turn on the computer to continue the recovery process.
8. After you restart the computer, the computer prompts you for a supplemental
Rescue and Recovery disc. If you have a supplemental Rescue and Recovery
disc, click OK and insert the supplemental disc. If you do not have a
supplemental disc, click No.
General descriptions
19
Related service information
9. When prompted, insert the appropriate Product Recovery disc and then click
OK. The second phase of the recovery process begins.
10. When all of the data has been copied from the last Product Recovery disc in
the set, a message is displayed prompting you to restart the computer.
Remove the disc and then click Yes, then a message is displayed asking you
to continue the recovery process. Click Continue to restart your computer,
then the computer restarts and the third phase of the recovery process begins.
11. When the recovery process is complete, the Welcome to Microsoft® Windows®
screen is displayed. Follow the instructions on the screen to complete the
Windows setup.
Passwords
As many as three passwords may be needed for any Lenovo 3000 computer: the
power-on password (POP), the hard-disk password (HDP), and the supervisor
password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed or Password on Boot is disabled in the BIOS
Setup Utility, the password prompt does not appear when the
operating system is booted.
Power-on password:
A power-on password (POP) protects the system from being powered on by an
unauthorized person. The password must be entered before an operating system
can be booted.
Hard-disk password:
There are two hard-disk passwords (HDPs):
v User HDP—for the user
v Master HDP—for the system administrator, who can use it to get access to the
hard disk even if the user has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The
Master + User mode requires two HDPs; the system administrator enters
both in the same operation. The system administrator then provides the user
HDP to the system user.
Attention: If the user HDP has been forgotten, check whether a master HDP has
been set. If it has, it can be used for access to the hard disk drive. If no master
HDP is available, neither Lenovo nor Lenovo authorized servicers provide any
services to reset either the user or the master HDP, or to recover data from the
hard disk drive. The hard disk drive can be replaced for a scheduled fee.
Supervisor password:
A supervisor password (SVP) protects the system information stored in the BIOS
Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup
Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the
servicer, there is no service procedure to reset the password. The system board
must be replaced for a scheduled fee.
20
MT 0763 and 0764
Related service information
How to remove the power-on password
To remove a POP that you have forgotten, do the following:
(A) If an SVP is not known by the servicer:
1. Turn off the computer.
2. Remove the battery pack.
For how to remove the battery pack, see “1010 Battery pack” on page 46.
3. Remove the backup battery.
For how to remove the backup battery, see “1050 Backup battery” on page 50.
4. Turn on the computer and wait until the POST ends.
After the POST ends, the password prompt does not appear. The POP has been
removed.
5. Reinstall the backup battery and the battery pack.
(B) If an SVP is known by the servicer:
1. Turn on the computer; then, while the initial screen is displayed, press the
Lenovo CareSM button. The Rescue and Recovery screen opens.
2. Click Access BIOS. The System Restart Required window is displayed.
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Password.
6. Select Power-On Password*1.
7. Type the current SVP in the Enter Current Password field. Then leave the Enter
New Password field blank, and press Enter twice.
8. In the Changes have been saved window, press Enter.
9. Press F10; then, in the Setup confirmation window, select Yes .
Note: For some models, the BIOS menu marked *1 is User Password.
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten
and cannot be made available to the servicer, neither Lenovo nor Lenovo
authorized servicers provide any services to reset the user HDPs or to recover data
from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master HDP
are known, do the following:
1. Turn on the computer; then, while the initial screen is displayed, press the
Lenovo Care button. The Rescue and Recovery screen opens.
2. Click Access BIOS. The System Restart Required window is displayed.
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Password.
6. Select Hard-disk x password, where x is the letter of the hard disk drive. A
pop-up window opens.
7. Select Master HDP.
8. Type the current master HDP in the Enter Current Password field. then leave
the Enter New Password field blank, and press Enter twice.
9. Press F10.
General descriptions
21
Related service information
10. Select Yes in the Setup Configuration window.
Both user HDP and master HDP will have been removed.
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management modes:
screen blank, sleep (standby), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires, the
LCD backlight turns off.
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
v The LCD is powered off.
v The hard disk drive is powered off.
v The CPU stops.
To enter sleep (standby) mode, press Fn+F4.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
v If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
v If the battery indicator blinks orange, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected in the
“Power Management Properties” window, the computer goes into hibernation
mode.)
To cause the computer to return from sleep (standby) mode and resume operation,
do one of the following:
v Press the Fn key.
v Open the LCD cover.
v Turn on the power switch.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes operation:
v The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters sleep
(standby) mode. Wait a few seconds before taking any action to reenter
operation mode.
Hibernation mode
In hibernation mode, the following occurs:
v The system status, RAM, VRAM, and setup data are stored on the hard disk.
v The system is powered off.
22
MT 0763 and 0764
Related service information
To cause the computer to enter hibernation mode, do any of the following:
v Press the Fn+F12 keys.
v If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action.
– Closing the lid.
– Pressing the power button.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
v If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the hard disk drive, the parallel connector, or
the diskette drive within that time.
v If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive is
read, and system status is restored from the hard disk drive.
General descriptions
23
Checkout guide
Checkout guide
Use the following procedures as a guide in identifying and correcting problems
with the Lenovo 3000 computer.
Note: The diagnostic tests are intended to test only Lenovo 3000 products. The use
of non-Lenovo 3000 products, prototype cards, or modified options can lead
to false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test
or by repeating the operation.
Testing the computer
The Lenovo 3000 computer has a test program called PC-Doctor for DOS (hereafter
called PC-Doctor.) You can detect errors by running the diagnostics test included in
PC-Doctor. This section is an overview of the procedure. For details that depend
on model-unique functions, refer to “Product overview” on page 30.
For some possible configurations of the computer, PC-Doctor might not run
correctly. To avoid this problem, you need to initialize the computer setup by use
of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility
screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled,
such as the serial port. If you test one of these devices, you will need to
enable it by using Configuration utility for DOS. The utility is available on
the following Web site: http://www.lenovo.com/support
Creating the PC-Doctor diagnostics diskette
To create the PC-Doctor disk from the Rescue and Recovery workspace , do as
follows:
1. Enter the Rescue and Recovery workspace by pressing the Lenovo Care button
during POST.
2. When the Rescue and Recovery workspace finishes loading, click Diagnostic
Diskette.
3. Authenticating the digital signature takes about 15 seconds; then the Lenovo
3000 computer will reboot into PC-DOS.
4. A batch file automatically starts up to prompt you through the process of
creating diskettes. You are notified of how many diskettes you will need.
a. You are prompted to insert each diskette in sequence.
b. Typically, all you need to do is to press the Enter key for the floppy drive;
the system then formats and creates the diskette.
c. Each diskette is erased and formatted with the PC-Doctor for DOS boot
image.
5. Once all the diskettes have been created, the Lenovo 3000 computer will reboot.
The user is asked to remove all diskettes from the drive, or to insert the first
diskette created if it is desired to run the diagnostics.
24
MT 0763 and 0764
Checkout guide
To run the test, do as follows:
1. Insert the PC-Doctor disk into the diskette drive; then power on the computer.
If the computer cannot be powered on, go to “Power system checkout” on page
26, and check the power sources.
If an error code appears, go to “Symptom-to-FRU index” on page 36.
On the first screen, select the model and press Enter. Follow the instructions on
the screen.
2. The main panel of PC-Doctor appears.
3. Select Diagnostics with the arrow keys, and press Enter.
A pull-down menu appears. (Its exact form depends on the model.)
Note: PC-Doctor menu does not mean the formal support device list. Some
unsupported device names may appear in the PC-Doctor menu.
Diagnostics
Interactive Tests
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Memory Test - Full
Memory Test - Quick
PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Diagnostics
v
v
v
v
v
v
v
v
v
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Memory Test – Full
Memory Test – Quick
Interactive Tests
v
v
v
v
Keyboard
Video
Mouse
System Load
Notes:
v In the Keyboard test in Interactive Tests, the Fn key should be held down with
M key for at least 2 seconds; otherwise, it cannot be sensed.
v Video Adapter test supports only the LCD display on the Lenovo 3000
computer. If you have an external monitor attached to your computer, detach it
before running PC-Doctor for DOS.
4. Run the applicable function test.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows
messages describing it.
6. To exit the test, select Quit — Exit Diag.
To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset
them if they are incorrect.
General descriptions
25
Checkout guide
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
v
v
v
v
v
v
v
v
v
v
v
System Configuration
Memory Contents
Physical Disk Drives
Logical Disk Drives
VGA Information
IDE Drive Info
PCI Information
PNPISA Info
SMBIOS Info
VESA LCD Info
Hardware Events Log
Utility
v
v
v
v
v
v
v
v
v
v
v
Run External Tests
Surface Scan Hard Disk
Benchmark System
DOS Shell
Tech Support Form
Battery Rundown
View Test Log
Print Log
Save Log
Full Erase Hard Drive
Quick Erase Hard Drive
PC-Doctor for Windows
This product is designed to help you troubleshoot and resolve problems related to
your computer. Select one of the categories listed below to display symptoms and
solutions:
v CHECK SYSTEM HEALTH
v SYSTEM AND DEVICE TESTS
v LENOVO TROUBLESHOOTING
v CENTER
v SYSTEM REPORTS
v UPDATES AND SUPPORT
Power system checkout
To
1.
2.
3.
4.
5.
6.
7.
verify a symptom, do the following:
Turn off the computer.
Remove the battery pack.
Connect the ac adapter.
Check that power is supplied when you turn on the computer.
Turn off the computer.
Disconnect the ac adapter and install the charged battery pack.
Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
v “Checking the ac adapter” on page 27
v “Checking operational charging” on page 27
v “Checking the battery pack” on page 27
26
MT 0763 and 0764
Checkout guide
Checking the ac adapter
You are here because the computer fails only when the ac adapter is used.
v If the power-on indicator does not turn on, check the power cord of the ac
adapter for correct continuity and installation.
v If the computer does not charge during operation, go to ″Checking operational
charging.″
To check the ac adapter, do the following:
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the
following figure:
3
2
1
Pin
Voltage (V dc)
1
+20
2
0
3
Ground
(20V)
Note: Output voltage of pin no.2 of the ac adapter may be different from the
one you are servicing.
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, do the following:
v Replace the system board.
v If the problem persists, go to “Product overview” on page 30.
Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged
battery pack or a battery pack that has less than 50% of the total power remaining
when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn
on, remove the battery pack and let it return to room temperature. Reinstall the
battery pack. If the charge indicator or icon still does not turn on, replace the
battery pack.
If the charge indicator still does not turn on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95% of
the total power remains; under this condition the battery pack can charge to 100%
of its capacity. This protects the battery pack from being overcharged or from
having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon tray
of the Windows taskbar and wait for a moment (but do not click), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
General descriptions
27
Checkout guide
Note: If the battery pack becomes hot, it may not be able to charge. Remove it
from the computer and leave it at room temperature for a while. After it
cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1
(−) and 7 (+). See the following figure:
2(-)
3
4
5
7(+)
6(+)
Terminal
Voltage (V dc)
1, 2
Ground (−)
6, 7
+ 0 to + 12.6
1(-)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn
on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery
terminals 4 and 7. The resistance must be 4 to 30 K .
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
28
MT 0763 and 0764
Lenovo 3000 V100 and V200
Product overview . . . . . . . . . . . .
Specifications . . . . . . . . . . . . .
Status indicators . . . . . . . . . . . .
FRU tests . . . . . . . . . . . . . .
Fn key combinations . . . . . . . . . .
Symptom-to-FRU index . . . . . . . . . .
Numeric error codes . . . . . . . . . .
Error messages . . . . . . . . . . . .
Beep symptoms . . . . . . . . . . . .
No-beep symptoms . . . . . . . . . . .
LCD-related symptoms . . . . . . . . .
Intermittent problems . . . . . . . . . .
Undetermined problems . . . . . . . . .
FRU replacement notices . . . . . . . . . .
Screw notices . . . . . . . . . . . . .
Retaining serial numbers . . . . . . . . .
Restoring the serial number of the system unit
Retaining the UUID . . . . . . . . .
Reading or writing the ECA information . .
Removing and replacing a FRU . . . . . . . .
1010 Battery pack . . . . . . . . . . .
1020 Hard disk drive slot cover and hard disk
drive . . . . . . . . . . . . . . .
1030 DIMM slot cover . . . . . . . . . .
1040 DIMM . . . . . . . . . . . . .
1050 Backup battery . . . . . . . . . .
1060 PCI Express Mini Card slot cover and PCI
Express Mini Card for 802.11 a/b/g wireless
LAN . . . . . . . . . . . . . . . .
1070 PCI Express Mini Card slot cover and PCI
Express Mini Card 802.11 a/b/g/n wireless LAN
1080 Optical drive . . . . . . . . . . .
1090 Middle cover . . . . . . . . . . .
1100 Function board . . . . . . . . . .
1110 Keyboard . . . . . . . . . . . .
1120 Hinge covers, keyboard bezel, 5-1 Digital
Media Reader card, BDC, and fingerprint reader
card . . . . . . . . . . . . . . . .
1130 LCD unit . . . . . . . . . . . .
1140 Heat sink assembly, CPU, MDC,
ExpressCard slot, and system board . . . . .
© Copyright Lenovo 2007
30
30
33
34
35
36
36
38
39
39
40
41
41
42
42
42
43
43
43
45
46
47
49
49
50
51
52
55
55
56
57
59
67
70
1150 Fan and base cover (with speakers) . . . . 77
2010 LCD front bezel . . . . . . . . . . 79
2020 Inverter card . . . . . . . . . . . 80
2030 Integrated camera . . . . . . . . . 81
2040 LCD panel, LCD cable, and hinges . . . . 82
2050 Wireless LAN antenna cables . . . . . . 84
Locations . . . . . . . . . . . . . . . 86
Front view. . . . . . . . . . . . . . 86
Rear view . . . . . . . . . . . . . . 87
Bottom view . . . . . . . . . . . . . 87
Parts list . . . . . . . . . . . . . . . 88
Overall . . . . . . . . . . . . . . . 89
LCD FRUs . . . . . . . . . . . . . 101
12.1-in. WXGA TFT . . . . . . . . . 102
Keyboard . . . . . . . . . . . . . . 103
Keyboard for MT 0763 . . . . . . . . 103
Keyboard for MT 0764 . . . . . . . . 104
Recovery discs . . . . . . . . . . . . 105
Windows XP Professional CDs . . . . . 105
Windows XP Home Edition CDs . . . . . 106
Windows Vista Home Premium (32 bit)
DVDs for MT 0763 . . . . . . . . . 107
Windows Vista Home Premium (32 bit)
DVDs for MT 0764 . . . . . . . . . 108
Windows Vista Home Basic (32 bit) DVDs for
MT 0763 . . . . . . . . . . . . . 109
Windows Vista Home Basic (32 bit) DVDs for
MT 0764 . . . . . . . . . . . . . 110
Windows Vista Business (32 bit) DVDs for
MT 0763 . . . . . . . . . . . . . 111
Windows Vista Business (32 bit) DVDs for
MT 0764 . . . . . . . . . . . . . 112
Windows Vista Ultimate (32 bit) DVDs . . . 113
Corel software CDs . . . . . . . . . . 114
Miscellaneous parts . . . . . . . . . . 114
AC adapters . . . . . . . . . . . . . 115
Common parts list . . . . . . . . . . . 115
Tools . . . . . . . . . . . . . . 115
Power cords . . . . . . . . . . . . 116
Notices . . . . . . . . . . . . . . . 117
Trademarks . . . . . . . . . . . . . . 118
29
Product overview
Product overview
This section presents the following product-unique information:
v “Specifications”
v “Status indicators” on page 33
v “FRU tests” on page 34
v “Fn key combinations” on page 35
Specifications
The following table lists the specifications of the Lenovo 3000 V100 and V200:
Feature
Description
Processor
v Intel ® Core™ Solo processor T1300 (1.66 GHz), 2-MB L2
cache (667 MHz)
v Intel Core Duo processor T2050 (1.60 GHz), 2-MB L2
cache (533 MHz)
v Intel Core Duo processor T2250 (1.73 GHz), 2-MB L2
cache (533 MHz)
v Intel Core Duo processor T2300 (1.66 GHz), 2-MB L2
cache (667 MHz)
v Intel Core Duo processor T2300E (1.66 GHz), 2-MB L2
cache (667 MHz)
v Intel Core Duo processor T2350 (1.86 GHz), 2-MB L2
cache (533 MHz)
v Intel Core Duo processor T2400 (1.83 GHz), 2-MB L2
cache (667 MHz)
v Intel Core Duo processor T2500 (2.0 GHz), 2-MB L2 cache
(667 MHz)
v Intel Core 2 Duo processor T5200 (1.60 GHz), 2-MB L2
cache (533 MHz)
v Intel Core 2 Duo processor T5300 (1.73 GHz), 2-MB L2
cache (533 MHz)
v Intel Core 2 Duo processor T5600 (1.83 GHz), 2-MB L2
cache (667 MHz)
v Intel Core 2 Duo processor T7100 (1.83 GHz), 2-MB L2
cache (800 MHz)
v Intel Core 2 Duo processor T7200 (2.0 GHz), 4-MB L2
cache (667 MHz)
v Intel Core 2 Duo processor T7300 (2.0 GHz), 4-MB L2
cache (800 MHz)
v Intel Core 2 Duo processor T7500 (2.2 GHz), 4-MB L2
cache (800 MHz)
Bus architecture
v
v
v
v
v
v
(continued)
30
MT 0763 and 0764
667-MHz PSB
667-MHz DDR2 SDRAM (PC2-5300)
HUB link
PCI bus
LPC bus
PCI Express bus
Product overview
Feature
Description
Graphic memory chip
v Intel 915GM/PM
v Intel 945GM
v Intel 965GM
Display
v 12.1-inch wide, 16M colors, WXGA (1280 × 768 resolution)
TFT color LCD
Standard memory
v
v
v
v
v
v
256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 2
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 2
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
Optional memory
v
v
v
v
256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
Maximum of 2.0 GB for MT 0763
Maximum of 4.0 GB for MT 0764
CMOS RAM
v 242 bytes
Hard disk drive
v
v
v
v
v
v
40 GB, 5400 rpm, 9.5 mm high, SATA interface
60 GB, 5400 rpm, 9.5 mm high, SATA interface
80 GB, 5400 rpm, 9.5 mm high, SATA interface
100 GB, 5400 rpm, 9.5 mm high, SATA interface
120 GB, 5400 rpm, 9.5 mm high, SATA interface
160 GB, 5400 rpm, 9.5 mm high, SATA interface
Supported hard disk drives are depend on the model.
Optical drive
v DVD/CD-RW combo drive, 12.7 mm high
v DVD-RAM/RW drive, 12.7 mm high
I/O port
v
v
v
v
v
v
v
v
5-1 Digital Media Reader
Fingerprint reader (some models)
External monitor connector
Stereo headphone jack
Monaural microphone jack
RJ11 connector
RJ45 connector
Universal serial bus (USB) connector × 3 (compatible with
USB 1.1 and 2.0)
v IEEE 1394 connector
(continued)
Lenovo 3000 V100 and V200
31
Product overview
32
MT 0763 and 0764
Feature
Description
Internal modem
v 56.6 Kbps
Audio
v Built-in stereo speakers
v Software control volume
Ethernet (on the system
board)
v 10/100 Ethernet
Mini PCI adapter
v
v
v
v
ExpressCard slot
v ExpressCard (34 module, 54 module)
Bluetooth wireless (some
models)
v Bluetooth daughter card
Modem
v MDC-1.5, 56 kbps V.92 for MT 0763
v AMoM, 56 kbps V.92 for MT 0764
Touch pad
Yes
Battery
v Li-ion battery (3 cells) 2.6 Ah
v Li-ion battery (6 cells) 2.6 Ah
AC adapter
v 65-watt (20V) slim type
Preinstalled operating
system
v
v
v
v
v
v
Intel PRO Wireless 3945ABG Mini-PCI Express Adapter
Broadcom 802.11ag WLAN PCI-E Mini Card
Broadcom 802.11bg WLAN PCI-E Mini Card
ThinkPad® 11a/b/g/n Wireless LAN Mini-PCI Express
Adapter
v Intel Wireless WiFi Link 4965AGN
Windows
Windows
Windows
Windows
Windows
Windows
XP Professional
XP Home Edition
Vista™ Home Premium (32 bit)
Vista Home Basic (32 bit)
Vista Business (32 bit)
Vista Ultimate (32 bit)
Product overview
Status indicators
The system status indicators show the status of the computer, as follows:
1
2
9
3
8
4
7
5
6
Indicator
Meaning
1
Caps lock
Caps Lock mode is enabled. You can enter all alphabetic
characters (A-Z) in uppercase without pressing the Shift key. To
enable or disable Caps Lock mode, press the CapsLk key.
2
Num lock
The numeric keypad on the keyboard is enabled. To enable or
disable the keypad, press and hold the Fn key, and press the
NmLk key.
3
5-1 Digital
Media Reader
status
A card in the 5-1 Digital Media Reader is being used to read and
write data. When this indicator is blinking, do not put the
computer into sleep (standby) mode, remove the card from the
slot, or turn off the computer.
4
Device Access
A hard disk drive or an optical drive is being used to read or
write data. When this indicator is blinking, do not put the
computer into sleep (standby) mode, remove the device from the
bay, or turn off the computer.
Note: Do not move the system while this indicator is on. Sudden
physical shock could cause drive errors.
5
Power on
The computer is on and ready to use. This indicator stays lit
whenever the computer is on and is not lit when the computer is
in sleep (standby) mode.
6
Sleep (standby)
status
Green:
The computer is in sleep (standby) mode.
Blinking green:
The computer is entering sleep (standby) mode or hibernation
mode, or is resuming normal operation.
Lenovo 3000 V100 and V200
33
Product overview
Indicator
Meaning
7
Battery status
Green:
The battery is charged between 80% to 100% of the capacity,
and being discharged between 0% to 80% of the capacity.
Blinking green:
The battery is charged between 20% to 80% of the capacity,
and being charged.
Orange:
The battery is charged between 5% and 20% of the capacity,
and being discharged.
Blinking orange (slow):
The battery is charged between 5% to 20% of the capacity,
and being charged.
Blinking orange (rapid):
The battery is charged between 0% to 5% of the capacity.
8
Bluetooth status
Green:
Bluetooth wireless is operational, and the radio link is ready
for use.
Blinking green:
Data is being transmitted.
R
9
Wireless status
Green:
The wireless feature (the IEEE 802.11 standard or the IEEE
802.11n) is on, and the radio link is ready for use.
Blinking green:
Data is being transmitted.
FRU tests
The following table shows the test for each FRU.
34
MT 0763 and 0764
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
LCD unit
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
Keyboard
1. Diagnostics --> Systemboard --> Keyboard
2. Interactive Tests --> Keyboard
Hard disk drive
Diagnostics --> Fixed Disks
Diskette drive
v Diagnostics --> Diskette Drives
Memory
1. If two DIMMs are installed, remove one of them and run
Diagnostics --> Memory Test—Quick.
2. If the problem does not recur, return the DIMM to its place,
remove the other one, and run the test again.
3. If the test does not detect the error, run Diagnostics -->
Memory Test—Full.
Product overview
Fn key combinations
The following table shows the function of each combination of Fn with a function
key.
Key combination Description
Fn+F1
Volume down.
Fn+F2
Volume up.
Fn+F3
Reserved.
Fn+F4
Put the computer in sleep (standby) mode. To return to normal
operation, press the Fn key only, without pressing a function key.
Fn+F5
Enable or disable the built-in wireless networking features and the
Bluetooth features. If you press Fn+F5, a list of wireless features is
displayed. You can quickly change the power state of each feature in
the list.
Fn+F6
Reserved.
Fn+F7
Open the window for Choose Presentation or Display scheme. If you
press this combination of keys, a list of schemes is displayed in the
window. You can quickly select a scheme in the list.
Fn+F8
Reserved.
Fn+F9
Reserved.
Fn+F10
Make the computer display less bright.
Fn+F11
Make the computer display brighter.
Fn+F12
Put the computer into hibernation mode. To return to normal operation,
press the power button.
Fn+Esc
Mute the sound from the computer.
Fn+Insert
Scroll Lock (ScrLk).
Fn+Delete
Numeric Lock (NmLk)
Fn+PrtSc
Has the same function as the SysRq key.
Fn+Pause
Has the same function as the Break key.
Fn+PgUp
Has the same function as the Home key.
Fn+PgDn
Has the same function as the End key.
Fn+cursor keys
These key combinations work with Windows Media Player. Fn+down
arrow key works for the Play or Pause button, Fn+up arrow key for the
Stop button, Fn+right arrow key for the Next Track button, and Fn+left
arrow key for the Previous Track button.
Lenovo 3000 V100 and V200
35
Symptom-to-FRU index
Symptom-to-FRU index
The symptom-to-FRU index in this section lists symptoms and errors and their
possible causes. The most likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the
column headed “FRU or action, in sequence.” If replacing a FRU does not
solve the problem, put the original part back in the computer. Do not
replace a nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are
likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system operation.
In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If
the symptom is not described there, go to “Intermittent problems” on page 41.
Note
For a device not supported by diagnostic codes in the Lenovo 3000 notebook
computers, see the manual for that device.
Numeric error codes
36
MT 0763 and 0764
Symptom or error
FRU or action, in sequence
0200
Failure Fixed Disk
1. Reseat the hard disk drive.
2. Load Setup Defaults in BIOS Setup
Utility.
3. Hard disk drive.
4. System board.
021x
Keyboard error
1. Keyboard.
2. System board.
0220
Monitor type does not match CMOS—Run
SETUP
Load Setup Defaults in BIOS Setup Utility.
0230
Shadow RAM Failed at offset:nnnn
System board.
0231
System RAM Failed at offset:nnnn
1. DIMM.
2. System board.
0232
Extended RAM Failed at offset:nnnn
1. DIMM.
2. System board.
0250
System battery is dead—Replace and run
SETUP
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0251
System CMOS checksum bad—Default
configuration use
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
Symptom-to-FRU index
Symptom or error
FRU or action, in sequence
0260
System timer error
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0270
Real time clock error
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0280
Previous boot incomplete— Default
configuration used
1. Load “Setup Default” in BIOS Setup
Utility.
2. DIMM.
3. System board.
02F4
EISA CMOS not writable
1. Load Setup Defaults in BIOS Setup
Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed
1. DIMM.
2. System board.
02F6
Software NMI failed
1. DIMM.
2. System board.
02F7
Fail-safe timer NMI failed
1. DIMM.
2. System board.
Lenovo 3000 V100 and V200
37
Symptom-to-FRU index
Error messages
Symptom or error
FRU or action, in sequence
Unsupported memory.
DIMM. Make sure to use supported
memory.
Device address conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid system configuration data.
1. DIMM.
2. System board.
I/O device IRQ conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Hibernation error.
1. Restore the system configuration to
what it was before the computer
entered hibernation mode.
2. If memory size has been changed,
re-create the hibernation file.
Fan error.
1. Fan.
2. Thermal grease.
3. System board.
Thermal sensing error.
System board.
Authentication of system services failed.
Press <Esc> to resume.
The Predesktop Area in the HDD is
corrupted. Restore it from a recovery disc.
Cannot boot from any device.
Check the status of device which you want
to boot from.
Device not found.
1. The device you want to boot from.
2. System board.
Device Error.
1. The device you want to boot from.
2. System board.
No valid operating system.
1. Check that the operating system has no
failure and is installed correctly.
2. Reinstall the operation system.
Excluded from boot order.
v Enter the BIOS Setup Utility and add the
device in boot order.
38
MT 0763 and 0764
Symptom-to-FRU index
Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank, unreadable, or
flashing LCD.
1.
2.
3.
4.
One long and two short beeps, and a blank
or unreadable LCD.
1. System board.
2. LCD assembly.
3. DIMM.
Two short beeps with error codes.
POST error. See “Numeric error codes” on
page 36.
Two short beeps and a blank screen.
1. System board.
2. DIMM.
Three short beeps, pause, three more short
beeps, and one short beep.
1. DIMM.
2. System board
Reseat the LCD connector.
LCD assembly.
External CRT.
System board.
One short beep, pause, three short beeps,
pause, three more short beeps, and one short
beep.
Only the cursor appears.
Reinstall the operating system.
Four cycles of four short beeps and a blank
screen.
System board (security chip)
Five short beeps and a blank screen.
System board
No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is
and no POST.
connected tightly and correctly.
2. DIMM.
3. System board.
No beep, power-on indicator on, and LCD
blank during POST.
1. Reseat DIMM.
The power-on password prompt appears.
A power-on password or a supervisor
password is set. Type the password and
press Enter.
The hard-disk password prompt appears.
A hard-disk password is set. Type the
password and press Enter.
2. System board.
Lenovo 3000 V100 and V200
39
Symptom-to-FRU index
LCD-related symptoms
Important
The TFT LCD for the notebook computer contains many thin-film transistors
(TFTs). The presence of a small number of dots that are missing, discolored,
or always lighted is characteristic of TFT LCD technology, but excessive pixel
problems can cause viewing concerns. The LCD should be replaced if the
number of missing, discolored, or lighted dots in any background is:
v WXGA: 8 or more bright dots, 8 or more dark dots, or a total of 9 or more
bright and dark dots.
Note: A bright dot means a pixel is always on (white or color.) A dark dot
means a pixel is always off (black color.)
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, and a
blank LCD during POST.
System board.
v
v
v
v
LCD
LCD
LCD
LCD
backlight not working.
too dark.
brightness cannot be adjusted.
contrast cannot be adjusted.
v
v
v
v
LCD screen unreadable.
Characters missing pixels.
Screen abnormal.
Wrong color displayed.
Horizontal or vertical lines displayed on
LCD.
40
MT 0763 and 0764
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
1. See important note for “LCD-related
symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
4. System board.
LCD assembly.
Symptom-to-FRU index
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have
nothing to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. FRU replacement should be considered only when a
problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the
test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if
wrong devices are installed, or if the system simply is not operating, follow these
procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating
correctly. (See “Power system checkout” on page 26.)
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-Lenovo 3000 devices
b. Devices attached to the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive
f. External diskette drive or optical drive
g. DIMM
h. Optical disk or diskette in the internal drive
i. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time
until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not
replace a nondefective FRU):
a. System board
b. LCD assembly
Lenovo 3000 V100 and V200
41
FRU replacement notices
FRU replacement notices
This section contains notices related to removing and replacing parts. Read this
section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo 3000 computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
v They maintain tight connections.
v They do not easily come loose, even with shock or vibration.
v They are harder to tighten.
v Each one should be used only once.
Do the following when you service this machine:
v Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 114) in your
tool bag.
v Always use new screws.
v Use a torque screwdriver if you have one.
Tighten screws as follows:
v Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the
plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the
logic card:
180 degrees more
(Cross-section)
v Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
v Make sure that you use the correct screw. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a screw
that you removed. Use a new one. Make sure that all of the screws are
tightened firmly.
v Ensure torque screwdrivers are calibrated correctly following country
specifications.
Retaining serial numbers
This section includes the following descriptions:
v “Restoring the serial number of the system unit” on page 43
42
MT 0763 and 0764
FRU replacement notices
v “Retaining the UUID”
v “Reading or writing the ECA information”
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was
loaded with the serial numbers of the system and all major components. These
numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the system
unit to its original value.
Before replacing the system board, save the original serial number by doing the
following:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial number
of the system unit is listed as follows:
v 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached to
the bottom of the computer.
After you have replaced the system board, restore the serial number by doing the
following:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM.
Follow the instructions on the screen.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to
your computer at production and stored in the EEPROM of your system board.
The algorithm that generates the number is designed to provide unique IDs until
the year A.D. 3400. No two computers in the world have the same number.
When you replace the system board, you must set the UUID on the new system
board as follows:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 4. Assign UUID.
A new UUID is created and written. If a valid UUID already exists, it is not
overwritten.
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the
EEPROM of the system board. The electronic storage of this information simplifies
the procedure to check if the ECA has been previously applied to a machine. The
machine does not need to be disassembled to check for the ECA application.
Lenovo 3000 V100 and V200
43
FRU replacement notices
To check what ECAs have been previously applied to the machine, use the ECA
Information Read/Write function on the CE Utility Diskette for Lenovo 3000
notebooks.
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM
and follow the instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and
follow the instruction on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to
reflect the ECA's application. Use the CE Utility Diskette for Lenovo 3000
notebooks to update the EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the
ECA is assumed be the same as the machine type of the machine that had
the ECA applied to it.
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM,
and follow the instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and
follow the instruction on the screen.
If the system board is being replaced, try to read the ECA information from the old
system board and transfer the information to the new system. If the system board
is inoperable, this will not be possible.
44
MT 0763 and 0764
Removing and replacing a FRU
Removing and replacing a FRU
This section presents directions and drawings for use in removing and replacing a
FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified.
An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 42.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
Any such FRUs are listed at the top of the page. Remove them in the order in
which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the
drawings by the numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the
arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the
drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any
notes that pertain to replacement. For information about connecting and
arranging internal cables, see “Locations” on page 86.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Attention: After replacing a FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none are
loose inside the computer. Verify this by shaking the computer gently and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a ground
point with one hand or by using an electrostatic discharge (ESD) strap (P/N
6405959).
Lenovo 3000 V100 and V200
45
Removing and replacing a FRU
1010 Battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Unlock the battery release lever 1 and holding the battery release lever in the
unlocked position 2, remove the battery pack in the direction shown by arrow
3.
2
1
3
46
MT 0763 and 0764
Removing and replacing a FRU
1020 Hard disk drive slot cover and hard disk drive
For access, remove this FRU:
v “1010 Battery pack” on page 46
Attention
v Do not drop the hard disk drive or apply any physical shock to it. The
hard disk drive is sensitive to physical shock. Improper handling can cause
damage and permanent loss of data.
v Before removing the drive, have the user make a backup copy of all the
information on it if possible.
v Never remove the drive while the system is operating or is in suspend
mode.
Note: Loosen the screws 1, but do not remove them.
2
1
(continued)
Lenovo 3000 V100 and V200
47
Removing and replacing a FRU
4
3
5
When installing: Make sure that the hard disk drive connector is attached firmly.
48
MT 0763 and 0764
Removing and replacing a FRU
1030 DIMM slot cover
For access, remove this FRU:
v “1010 Battery pack” on page 46
Note: Loosen the screws 1, but do not remove them.
2
1
1040 DIMM
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1030 DIMM slot cover”
1
2
1
When installing: Insert the notched end of the DIMM into the socket. Press the
DIMM firmly, and pivot it until it snaps into the place. Make
sure that it is firmly fixed in the slot and does not move easily.
Lenovo 3000 V100 and V200
49
Removing and replacing a FRU
1050 Backup battery
DANGER
Use only the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1030 DIMM slot cover” on page 49
1
2
When installing: Make sure that the battery connector is attached firmly.
50
MT 0763 and 0764
Removing and replacing a FRU
1060 PCI Express Mini Card slot cover and PCI Express Mini
Card for 802.11 a/b/g wireless LAN
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
Note: Loosen the screws 1, but do not remove them.
2
1
4
4
3
3
5
In step 3, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them
in direction of the arrow.
Step
Screw (quantity)
Color
Torque
4
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Plug the gray cable into the jack labeled MAIN on the card, and
the black cable into the jack labeled AUX.
Lenovo 3000 V100 and V200
51
Removing and replacing a FRU
1070 PCI Express Mini Card slot cover and PCI Express Mini
Card 802.11 a/b/g/n wireless LAN
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
Note: Loosen the screws 1, but do not remove them.
2
1
(continued)
52
MT 0763 and 0764
Removing and replacing a FRU
For MT 0763
4
4
3
3
5
In step 3, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them
in direction of the arrow.
Step
Screw (quantity)
Color
Torque
4
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Plug the gray cable into the jack labeled TR1 on the card, and
the black cable into the jack labeled TR2.
(continued)
Lenovo 3000 V100 and V200
53
Removing and replacing a FRU
For MT 0764
4
4
3
5
In step 3, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug them
in direction of the arrow.
Step
Screw (quantity)
Color
Torque
4
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Plug the gray cable (MAIN) into the jack labeled 1, the black
cable (AUX) into the jack labeled 2, and the white cable (MIMO)
into the jack labeled 3 on the card.
54
MT 0763 and 0764
Removing and replacing a FRU
1080 Optical drive
For access, remove this FRU:
v “1010 Battery pack” on page 46
1
3
2
Step
Screw (quantity)
Color
Torque
1
M2.5 × 5 mm, pan-head, nylon-coated (1)
Silver
0.392 Nm
(4 kgfcm)
1090 Middle cover
For access, remove this FRU:
v “1010 Battery pack” on page 46
4
4
4
4
1
2
3
Lenovo 3000 V100 and V200
55
Removing and replacing a FRU
1100 Function board
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1090 Middle cover” on page 55
3
1
1
2
56
MT 0763 and 0764
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
Removing and replacing a FRU
1110 Keyboard
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1090 Middle cover” on page 55
1
Step
Screw (quantity)
Color
Torque
1
M2.5 × 7 mm, pan-head, nylon-coated (1)
Black
0.392 Nm
(4 kgfcm)
(continued)
Lenovo 3000 V100 and V200
57
Removing and replacing a FRU
2
3
3
4
Lift the keyboard a little in the direction shown by arrow 2. Then unlock the
connector 3 and detach the connector 4.
When installing:
1. Make sure that the keyboard connector is attached firmly. Then lock the
connector.
2. Make sure that the front side of the keyboard is under the frame.
58
MT 0763 and 0764
Removing and replacing a FRU
1120 Hinge covers, keyboard bezel, 5-1 Digital Media Reader
card, BDC, and fingerprint reader card
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1090 Middle cover” on page 55
v “1100 Function board” on page 56
v “1110 Keyboard” on page 57
Note: 5-1 Digital Media Reader card, BDC, and fingerprint reader card are
attached underside of the keyboard bezel.
1
2
2
2
2
1
2
2
Step
Screw (quantity)
Color
Torque
1
M2.5 × 13 mm, pan-head, nylon-coated (2)
Silver
0.392 Nm
(4 kgfcm)
2
M2.5 × 5 mm, pan-head, nylon-coated (7)
Silver
0.392 Nm
(4 kgfcm)
(continued)
Lenovo 3000 V100 and V200
59
Removing and replacing a FRU
Remove the hinge cap L 3a and the hinge cap R 3b.
3b
3a
Note: Steps 4 and 5 are only for MT 0763.
4
5
5
5
(continued)
60
MT 0763 and 0764
Removing and replacing a FRU
Release the antenna cables from the cable guides of the frame. In step 6, take
care not to damage the cables when you pull out them from the guide hole.
7
7
7
6
When installing: Route the antenna cables along the cable guides. When you route
the cables, do not tense them. To do so, the cables may get
damaged by the cable guides of the frame, and may cause a
broken wire.
(continued)
Lenovo 3000 V100 and V200
61
Removing and replacing a FRU
8
8
8
8
8
When installing: Make sure that all the connectors are attached firmly.
9
9
9
Step
Screw (quantity)
Color
Torque
9
M2.5 × 5 mm, pan-head, nylon-coated (3)
Silver
0.392 Nm
(4 kgfcm)
(continued)
62
MT 0763 and 0764
Removing and replacing a FRU
10
11
Lenovo 3000 V100 and V200
63
Removing and replacing a FRU
To remove the 5-1 Digital Media Reader card, do as follows:
1
1
2
a
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
3
3
4
When installing: Make sure that all the connectors are attached firmly.
64
MT 0763 and 0764
Removing and replacing a FRU
To remove the BDC, do as follows:
2
1
1
3
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that the connector is attached firmly.
Lenovo 3000 V100 and V200
65
Removing and replacing a FRU
To remove the fingerprint reader card, do as follows:
1
1
1
3
2
3
3
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (3)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that the connector is attached firmly.
66
MT 0763 and 0764
Removing and replacing a FRU
1130 LCD unit
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1090 Middle cover” on page 55
v “1100 Function board” on page 56
v “1110 Keyboard” on page 57
1
1
2
2
Step
Screw (quantity)
Color
Torque
1
M2.5 × 5 mm, pan-head, nylon-coated (2)
Silver
0.392 Nm
(4 kgfcm)
2
M2.5 × 5 mm, pan-head, nylon-coated (2)
Silver
0.392 Nm
(4 kgfcm)
(continued)
Lenovo 3000 V100 and V200
67
Removing and replacing a FRU
5
3
4
4
3
Step
Screw (quantity)
Color
Torque
3
M2.5 × 5 mm, pan-head, nylon-coated (2)
Silver
0.392 Nm
(4 kgfcm)
4
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that the LCD connector 5 is attached firmly.
(continued)
68
MT 0763 and 0764
Removing and replacing a FRU
6
6
When installing: When you attach the LCD unit, make sure that you do not pinch
the antenna cable.
Lenovo 3000 V100 and V200
69
Removing and replacing a FRU
1140 Heat sink assembly, CPU, MDC, ExpressCard slot, and
system board
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 46
v “1020 Hard disk drive slot cover and hard disk drive” on page 47
v “1030 DIMM slot cover” on page 49
v “1040 DIMM” on page 49
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1080 Optical drive” on page 55
v “1090 Middle cover” on page 55
v “1100 Function board” on page 56
v “1110 Keyboard” on page 57
v “1120 Hinge covers, keyboard bezel, 5-1 Digital Media Reader card, BDC, and
fingerprint reader card” on page 59
v “1130 LCD unit” on page 67
Note: Heat sink assembly, CPU, MDC, and ExpressCard slot are attached to the
system board.
1
3
2
Step
Screw (quantity)
Color
Torque
3
M2.5 × 5 mm, pan-head, nylon-coated (1)
Silver
0.392 Nm
(4 kgfcm)
When installing: Make sure that the connectors are firmly attached.
70
MT 0763 and 0764
Removing and replacing a FRU
5
4
Remove the heat sink as follows:
2
1
3
2
2
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (1)
Silver
0.245 Nm
(2.5 kgfcm)
Note: Loosen the screws 2, but do not remove them.
(continued)
Lenovo 3000 V100 and V200
71
Removing and replacing a FRU
When installing: Before you attach a new thermal module to the computer, peel
off the covering film of thermal grease. Then attach the thermal
module to the computer.
For MT 0763
a
For MT 0764
a
(continued)
72
MT 0763 and 0764
Removing and replacing a FRU
Remove the CPU as follows:
Attention: CPU is extremely sensitive. When you service the CPU, avoid any
kind of rough handling.
Rotate the head of the screw in the direction shown by arrow 1 to release the
lock; then remove the CPU in the direction shown by arrow 2.
1
a
b
2
When installing: Place the CPU on the CPU socket a, and then rotate the head
of the screw in the direction shown by arrow b to secure the
CPU.
(continued)
Lenovo 3000 V100 and V200
73
Removing and replacing a FRU
Remove the MDC as follows:
For MT 0763
1
1
2
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
3
4
When installing: Make sure that the connector on the underside of the card is
attached to the system board firmly, and then fasten the screws.
(continued)
74
MT 0763 and 0764
Removing and replacing a FRU
For MT 0764
1
1
3
2
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that the connector on the underside of the card is
attached to the system board firmly, and then fasten the screws.
(continued)
Lenovo 3000 V100 and V200
75
Removing and replacing a FRU
Remove the ExpressCard slot as follows:
1
1
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 2.5 mm, pan-head, nylon-coated (4)
Silver
0.245 Nm
(2.5 kgfcm)
Turn over the system board, and disconnect the ExpressCard slot assembly.
2
When installing: Make sure that the connector is attached firmly, and then fasten
the screws.
76
MT 0763 and 0764
Removing and replacing a FRU
1150 Fan and base cover (with speakers)
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 46
v “1020 Hard disk drive slot cover and hard disk drive” on page 47
v “1030 DIMM slot cover” on page 49
v “1040 DIMM” on page 49
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1080 Optical drive” on page 55
v “1090 Middle cover” on page 55
v “1100 Function board” on page 56
v “1110 Keyboard” on page 57
v “1120 Hinge covers, keyboard bezel, 5-1 Digital Media Reader card, BDC, and
fingerprint reader card” on page 59
v “1130 LCD unit” on page 67
1
1
2
Step
Screw (quantity)
Color
Torque
1
M2.5 × 5 mm, pan-head, nylon-coated (2)
Silver
0.392 Nm
(4 kgfcm)
When installing: Make sure that the fan connector is attached firmly.
Lenovo 3000 V100 and V200
77
Removing and replacing a FRU
Note: Applying labels to the bottom cover
When you replace the base cover, you need to stick some labels on the new
base cover. Some of the labels have been shipped with the new base cover,
and some may need to be reused from the old base cover.
Following labels are the typical labels stuck on the bottom side of the
computer when it is shipped.
a Windows license label (COA)
b MAC label (802.11 a/b/g)
c MAC label (802.3)
d Homologation label
e Product label
f Serial number label
a
f
c
b
e
d
For some models, you also need to apply one or two FCC labels or the other
types of labels. Check the old base cover; if it has one or two FCC labels or
the other types of labels, find duplicates of them in the package and apply
them to the new base cover.
78
MT 0763 and 0764
Removing and replacing a FRU
2010 LCD front bezel
For access, remove this FRU:
v “1010 Battery pack” on page 46
1
1
1
1
Step
1
Screw cap
Screw (quantity)
Color
Torque
M2.5 × 5 mm, pan-head,
nylon-coated (4)
Black
0.392 Nm
(4 kgfcm)
2
Lenovo 3000 V100 and V200
79
Removing and replacing a FRU
2020 Inverter card
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “2010 LCD front bezel” on page 79
1
2
1
4
3
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that connectors 3 and 4 are attached firmly.
Cable routing: Route the cables as shown in the following figure.
80
MT 0763 and 0764
Removing and replacing a FRU
2030 Integrated camera
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “2010 LCD front bezel” on page 79
Note: The part marked a is fragile and might be damaged by rough handling.
When you remove the camera, do not hold that part to avoid the damage.
a
1
1
2
3
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, pan-head, nylon-coated (2)
Silver
0.245 Nm
(2.5 kgfcm)
When installing: Make sure that connectors 2 is attached firmly.
Lenovo 3000 V100 and V200
81
Removing and replacing a FRU
2040 LCD panel, LCD cable, and hinges
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1090 Middle cover” on page 55
v “1110 Keyboard” on page 57
v “1100 Function board” on page 56
v “1130 LCD unit” on page 67
v “2010 LCD front bezel” on page 79
v “2020 Inverter card” on page 80
1
1
1
1
Step
Screw (quantity)
Color
Torque
1
M2.5 × 5 mm, pan-head, nylon-coated (6)
Black
0.392 Nm
(4 kgfcm)
Release the antenna cables from the cable guides.
2
(continued)
82
MT 0763 and 0764
2
Removing and replacing a FRU
5
4
3
When installing: Make sure that the camera connector is attached firmly.
Remove the hinges from the LCD panel.
6
7
6
6
7
6
Step
Screw (quantity)
Color
Torque
6
M2 × 3 mm, pan-head, nylon-coated (4)
Silver
0.245 Nm
(2.5 kgfcm)
Remove the LCD cable assembly from the LCD panel.
8
Lenovo 3000 V100 and V200
83
Removing and replacing a FRU
2050 Wireless LAN antenna cables
For access, remove these FRUs in order:
v “1010 Battery pack” on page 46
v “1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.11
a/b/g wireless LAN” on page 51
v “1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.11
a/b/g/n wireless LAN” on page 52
v “1090 Middle cover” on page 55
v “1110 Keyboard” on page 57
v “1100 Function board” on page 56
v “1130 LCD unit” on page 67
v “2010 LCD front bezel” on page 79
v “2020 Inverter card” on page 80
v “2040 LCD panel, LCD cable, and hinges” on page 82
For the antennas with two cables
2
4
2
1
2
3
1
Step
Screw (quantity)
Color
Torque
2
M2 × 4 mm, pan-head, nylon-coated (3)
Silver
0.245 Nm
(2.5 kgfcm)
Cable routing: Route the cables as shown in the following figure.
(continued)
84
MT 0763 and 0764
Removing and replacing a FRU
For the antennas with three cables
2
4
2
2
2
1
3
1
Step
Screw (quantity)
Color
Torque
2
M2 × 4 mm, pan-head, nylon-coated (4)
Silver
0.245 Nm
(2.5 kgfcm)
Cable routing: Route the cables as shown in the following figure.
Lenovo 3000 V100 and V200
85
Locations
Locations
Front view
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Integrated camera (for some models)
Power switch
Lenovo Care button
Instant on button
Volume control buttons
Keyboard
Fingerprint reader (for some models)
Touch pad
Touch pad buttons
System and power status indicators
Note: For the description of each indicator, see “Status indicators” on page
33.
ExpressCard slot
IEEE1394 connector
Stereo headphone jack
Microphone jack
External monitor connector
Universal serial bus (USB) connector
Security keyhole
System and power status indicators
Note: For the description of each indicator, see “Status indicators” on page
33.
1
2
3
4
5
6
7
18
8
17
9
16
15
14
10
13
12
11
86
MT 0763 and 0764
Locations
Rear view
1
2
3
4
5
6
7
8
USB connector
AC power connector
USB connector
RJ-45 (Ethernet) connector
RJ-11 (modem) connector
Optical drive
Wireless radio switch
5-1 Digital Media Reader
8
7
6
5
4
3
2
1
Bottom view
1
2
3
4
5
6
7
8
Battery pack latch
Battery pack
PCI Express Mini card slot
Memory card slot
Battery pack latch
Hard disk drive slot
System and power status indicators
Note: For the description of each indicator, see “Status indicators” on page
33.
Built-in stereo speakers
3
4
5
6
2
1
7
8
Lenovo 3000 V100 and V200
87
Parts list
Parts list
v Each FRU is available for all types or models, unless specific types or models are
specified.
v FRU with specific models listed and described as xxU (where U is an example of
a country designator) should be used for all models ending in U.
v FRU with specific models listed and described as 3Dx (where 3D is an example
of a unique configuration) should be used for all of these models, unless specific
country or region designator is specified.
v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two
asterisks (**) in the CRU ID column. An N in the CRU ID column means the
part is not a CRU. A single asterisk (*) means the part is an External CRU; two
asterisks (**) means the part is an Internal CRU.
Lenovo 3000 computers contain the following types of the external CRUs:
External CRUs (pluggable)
These CRUs unplug from the computer. Examples of these types of
CRUs include an ac adapter, an external keyboard, a mouse, a power
cord, a port replicator, a USB device, and an external bay device adapter.
External CRUs with latches
These CRUs have a latch to help you to remove and replace the part.
Examples of these types of CRUs include a battery pack, a cover such as
a memory card slot cover and a hard disk drive slot cover.
Lenovo 3000 computers contain the following types of the internal CRUs:
Internal CRUs (located behind an access panel)
These CRUs are isolated parts within the computer that are concealed by
an access panel that is typically secured by either one or two screws.
Once the access panel is removed, only the specific CRU is visible.
Examples of these types of CRUs include a memory card and a hard
disk drive.
Internal CRUs (located within the product itself)
These CRUs are accessible only by opening the outer case of the
computer. Examples of these CRUs include the parts beneath a cover
and they are secured by either one or two screws.
v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column
means the part is not a RoHS compliant FRU.
v FRUs marked with OP are available as options.
88
MT 0763 and 0764
Parts list
Overall
1
2
3
4
5
6
a
7
25
b
c
8
9
24
10
11
23
12
22
13
21
20
14
19
15
18
17
16
Lenovo 3000 V100 and V200
89
Parts list
No.
FRU
FRU no.
RoHS
ID
CRU
ID
a - c See “Miscellaneous parts” on page 114.
1
LCD unit (see “LCD FRUs” on page 101.)
2
Hinge caps
41W6375
R
N
3
Middle cover
41W6374
R
N
4
Keyboard (see “Keyboard” on page 103.)
5
Launch board for MT 0763
41W1333
R
N
Launch board for MT 0764
41R7645
R
N
Keyboard bezel assembly without a fingerprint reader
for MT 0763
v 0763-33x, 59x, 65x, 69x, 82x, 83x, 97x, 99x, A3x, A5x,
B3x, B7x, C3x, C5x, C6x, C7x, C8x, D5x, D9x, E2x,
E6x, E7x, E9x, F3x, G3x, G7x, J5, J7x, 2Gx, 2Px, 3Ax,
3Ex, 4Bx, 6Ax, 6Ex, 2Xx, 5Kx
41W6371
R
N
Keyboard bezel assembly without a fingerprint reader
for MT 0764
v 0764-22x
41R5801
R
N
Keyboard bezel assembly with a fingerprint reader for
41W6372
MT 0763
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,
44x, 46x, 49x, 62x, 64x, 66x, 68x, 77x, 84x, 85x, 86x,
88x, 89x, 93x, A2x, A4x, A6x, A8x, C2x, C4x, C9x, E3x,
E4x, E5x, E8x, G2x, G9x, J3x, J8x, J9x, 2Cx, 2Dx, 2Ex,
2Fx, 2Hx, 2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Fx, 3Gx, 3Hx,
4Ax, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx,
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Bx, 6Dx, 6Fx, 6Hx,
7Ax, 7Bx, 7Cx,7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx, 8Dx,
8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx,
4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,
5Yx, 5Zx, 6Jx, 6Kx
R
N
Keyboard bezel assembly with a fingerprint reader for
41R5802
MT 0764
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx
R
N
5-1 Digital Media Reader board
R
N
6
7
(continued)
90
MT 0763 and 0764
41W1332
Parts list
No.
FRU
FRU no.
RoHS
ID
CRU
ID
8
Bluetooth daughter card (BDC)
41W1163
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,
44x, 46x, 49x, 62x, 64x, 66x, 68x, 69x, 82x, 83x, 84x,
86x, 88x, 89x, 99x, A2x, A3x, A4x, A5x, A6x, A8x, B3x,
C2x, C4x, C6x, C7x, C8x, C9x, E2x, E3x, E4x, E5x, E6x,
E8x, G2x, J8x, J9x, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px,
2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax,
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx,
6Hx, 7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx,
8Cx, 8Dx, 8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx,
3Nx, 4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx,
4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux,
5Wx, 5Xx, 5Yx, 5Zx, 6Jx, 6Kx
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Hx, 4Jx, 4Lx, 4Mx,
4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx
R
N
9
Fingerprint reader card for MT 0763
41W1334
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x,
44x, 46x, 49x, 62x, 64x, 66x, 68x, 77x, 84x, 85x, 86x,
88x, 89x, 93x, A2x, A4x, A6x, A8x, C2x, C4x, C9x, E3x,
E4x, E5x, E8x, G2x, G9x, J3x, J8x, J9x, 2Cx, 2Dx, 2Ex,
2Fx, 2Hx, 2Qx, 2Rx, 2Sx, 3Cx, 3Dx, 3Fx, 3Gx, 3Hx,
4Ax, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx,
5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Bx, 6Dx, 6Fx, 6Hx,
7Ax, 7Bx, 7Cx,7Dx, 7Ex, 7Fx,7Gx, 8Ax, 8Bx, 8Cx, 8Dx,
8Ex, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx,
4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,
5Yx, 5Zx, 6Jx, 6Kx
R
N
Fingerprint reader card for MT 0764
41R5805
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x,
49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx,
4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx
R
N
System board assembly, 12W integrated
41W1321
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 33x, 34x, 36x, 38x,
43x, 44x, 46x, 49x, 59x, 62x, 64x, 65x, 66x, 68x, 69x,
77x, 82x, 83x, 84x, 85x, 86x, 88x, 89x, 93x, 97x, 99x,
A2x, A3x, A4x, A5x, A6x, A8x, B3x, B7x, C2x, C3x,
C4x, C5x, C6x, C7x, C8x, C9x, D5x, D9x, E2x, E3x,
E4x, E5x, E6x, E7x, E8x, E9x, F3x, G2x, G3x, G7x, G9x,
J3x, J5x, J7x, J8x, J9x
R
N
System board assembly, 12W integrated
41W1423
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx,
3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Cx,
4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex,
5Fx, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx,
7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx,
8Dx, 8Ex
R
N
10
(continued)
Lenovo 3000 V100 and V200
91
Parts list
No.
10
11
12
FRU
FRU no.
RoHS
ID
CRU
ID
System board assembly, 12W integrated
42W7671
v 0763- 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 2Xx, 3Lx, 3Mx, 3Nx,
4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx,
5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx,
5Xx, 5Yx, 5Zx, 6Jx, 6Kx
R
N
System board assembly, 12W integrated
v 0764-22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx,
2Cx, 2Dx, 2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x,
48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx,
4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux, 4Zx
41R5796
R
N
Modem daughter card (MDC) for MT 0763
41W1324
R
N
Modem daughter card (MDC) for MT 0764
41R5798
R
N
DVD/CD-RW combo drive assembly, 12.7 mm for MT 0763
v 0763-23x, 33x, 34x, 36x, 38x, 59x, 77x, 82x, 83x, 97x, A5x, B7x, C5x, C6x, C7x, C8x,
D5x, D9x, E3x, E4x, E5x, E6x, E7x, E9x, F3x, G3x, G7x, G9x, J3x, 3Ax, 3Ex, 3Fx, 5Jx,
6Bx, 7Ax, 7Bx, 8Ax, 8Bx, 8Dx, 8Ex, 5Xx, 5Yx
HLDS
27R2364
R
**
Panasonic
27R2370
R
**
DVD/CD-RW combo drive assembly, 12.7 mm for MT 0764
v 0764-22x, 44x, 45x, 46x, 4Lx, 4Mx, 4Px, 4Qx, 4Rx
HLDS
42T2016
R
**
Panasonic
42T2039
R
**
DVD-RAM/RW drive assembly, 12.7 mm for MT 0763
v 0763-22x, 25x, 26x, 27x, 29x, 43x, 44x, 46x, 49x, 62x, 64x, 65x, 66x, 68x, 69x, 84x,
85x, 86x, 88x, 89x, 93x, 99x, A2x, A3x, A4x, A6x, A8x, B3x, C2x, C3x, C4x, C9x,
E2x, E8x, G2x, J5x, J7x, J8x, J9x, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx,
3Cx, 3Dx, 3Gx, 3Hx, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx,5Hx, 6Ax, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 8Cx,
2Lx, 2Mx, 2Ux, 2Vx, 2Wx 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx,
4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx
HLDS
27R2368
R
**
Panasonic
27R2372
R
**
DVD-RAM/RW drive assembly, 12.7 mm for MT 0764
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Lx, 2Mx, 32x, 42x, 43x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux,
4Zx
13
HLDS
42T2021
R
**
Panasonic
42T2011
R
**
Base cover assembly for MT 0763
41W6373
R
N
Base cover assembly for MT 0764
41R5803
R
N
(continued)
92
MT 0763 and 0764
Parts list
No.
14
FRU
FRU no.
RoHS
ID
CRU
ID
Intel PRO Wireless 3945ABG Mini-PCI Express Adapter
v 0763-22x, 23x, 25x, 26x, 27x, 29x, 36x, 38x, 43x, 44x, 46x, 49x, 62x, 64x, 66x, 68x,
69x, 82x, 83x, 84x, 86x, 88x, 89x, 97x, 99x, A2x, A3x, A4x, A5x, A6x, A8x, B3x, B7x,
C2x, C3x, C4x, C6x, C7x, C8x, C9x, E2x, E3x, E4x, E5x, E8x, G2x, G3x, G7x, J5x,
J7x, 2Px, 2Qx, 2Rx, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx,
4Gx, 5Ax, 5Bx, 5Cx, 5Ex, 5Gx, 5Hx, 5Jx, 6Ax, 6Bx, 6Dx, 7Ax, 7Bx, 7Cx, 7Ex, 8Ax,
8Bx, 8Cx, 8Dx, 8Ex, 2Lx, 2Mx, 2Ux, 2Wx, 2Xx, 3Lx, 3Mx, 4Rx, 4Sx, 5Wx, 5Xx, 5Yx,
5Zx, 6Kx
v 0764-27x, 2Bx, 2Cx, 2Lx, 45x, 46x, 4Hx, 4Mx, 4Nx, 4Qx, 4Rx,
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,
xxV, xxY
42T0853
R
**
xxK
42T0857
R
**
xxE, xxJ
42T0859
R
**
xxG, xxR, xxT (802.11 b/g)
42T0861
R
**
Broadcom 802.11ag WLAN PCI-E Mini Card
v 0763-33x, 34x, 59x, 65x, 77x, 85x, 93x, C5x, D5x, D9x, E6x, E7x, E9x, F3x, G9x, J3x,
J8x, J9x, 4Jx, 4Nx, 5Px
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,
xxV, xxY
41W1297
R
**
xxG
41W1299
R
**
xxK
41W1301
R
**
xxE, xxJ
41W1303
R
**
Broadcom 802.11bg WLAN PCI-E Mini Card
v 0763-5Kx
v 0764-22x, 26x, 2Mx, 44x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Lx, 4Px, 4Tx, 4Ux, 4Zx
xxF, xxU, xxV
42T0819
R
**
xxE, xxJ, xxT
42T0821
R
**
xxA, xxB, xxG, xxH, xxK, xxL, xxM, xxP, xxQ, xxR,
xxS, xxY
42T0823
R
**
(continued)
Lenovo 3000 V100 and V200
93
Parts list
No.
14
FRU
FRU no.
RoHS
ID
CRU
ID
ThinkPad 11a/b/g/n Wireless LAN Mini-PCI Express Adapter
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Sx, 4Cx, 4Hx, 5Dx, 5Fx, 6Cx, 6Ex, 6Fx, 6Hx,
7Dx, 7Fx, 7Gx, 2Vx, 3Nx, 4Kx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Mx, 5Nx, 5Qx, 5Rx,
5Sx, 5Tx, 5Ux, 6Jx
xxA, xxB, xxF, xxG, xxH, xxL, xxM, xxP, xxQ, xxS,
xxU, xxY
42T0825
R
**
xxE, xxJ
42T0827
R
**
xxV
42T0829
R
**
xxK
42T0831
R
**
xxT, xxR (802.11 b/g/n)
42T0833
R
**
Intel Wireless WiFi Link 4965AGN
v 0764-23x, 24x, 25x, 28x, 29x, 2Ax, 2Dx, 32x, 42x, 43x, 47x, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx,
4Kx
15
16
xxA, xxB, xxF, xxH, xxL, xxM, xxP, xxQ, xxS, xxU,
xxV, xxY
42T0865
R
**
xxG
42T0867
R
**
xxE, xxJ
42T0871
R
**
PCI Express Mini card slot cover for MT 0763
41W6381
R
*
PCI Express Mini card slot cover for MT 0764
41R5808
R
*
SATA hard disk drive, 40 GB, 9.5 mm, 5,400 rpm
v 0763-34x, 59x, 77x, 97x, D9x, E3x, E7x, E9x, F3x, G3x, G9x, J3x, 3Ax, 6Bx, 7Ax, 7Bx,
8Ax
HGST
27R2379
R
**
Toshiba
27R2387
R
**
SATA hard disk drive, 40 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1801
v 0763-3Ax, 6Bx, 7Ax, 7Bx, 8Ax
R
**
(continued)
94
MT 0763 and 0764
Parts list
No.
16
FRU
FRU no.
RoHS
ID
CRU
ID
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm,
Toshiba
v 0763-36x, 65x, 69x, 82x, 99x, A3x, B3x, C3x, C6x, C8x,
E4x, E6x, J5x, 2Gx, 4Bx, 2Xx
27R2389
R
**
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm, HGST 27R2381
v 0763-36x, 65x, 69x, 82x, 99x, A3x, B3x, C3x, C6x, C8x,
E4x, E6x, J5x, 2Gx, 4Bx, 2Xx
v 0764-22x
R
**
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1803
v 0763-2Gx, 4Bx, 2Xx
v 0764-22x
R
**
SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm,
Seagate
v 0764-22x
42T1851
R
**
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm,
Toshiba
v 0763-22x, 23x, 25x, 26x, 33x, 38x, 49x, 62x, 66x, 83x,
84x, 85x, 86x, 88x, 89x, 93x, A4x, A5x, B7x, C2x, C4x,
C5x, C7x, C9x, D5x, E2x, E5x, E8x, G7x, J7x, J8x, 2Px,
2Sx, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax,
5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex, 3Lx,
4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx
27R2391
R
**
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm, HGST 27R2383
v 0763-22x, 23x, 25x, 26x, 33x, 38x, 49x, 62x, 66x, 83x,
84x, 85x, 86x, 88x, 89x, 93x, A4x, A5x, B7x, C2x, C4x,
C5x, C7x, C9x, D5x, E2x, E5x, E8x, G7x, J7x, J8x, 2Px,
2Sx, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Ax,
5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex, 3Lx,
4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,
4Mx, 4Px, 4Qx, 4Rx, 4Tx
R
**
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm, Fujitsu 42T1805
v 0763-2Px, 3Ex, 3Fx, 3Gx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx,
5Ax, 5Ex, 5Fx, 6Ax, 6Dx, 6Ex, 7Cx,7Fx, 8Bx, 8Dx, 8Ex,
3Lx, 4Tx, 4Yx, 5Kx, 5Px, 5Tx, 5Xx, 5Yx
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,
4Mx, 4Px, 4Qx, 4Rx, 4Tx
R
**
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm,
Seagate
v 0764-23x, 26x, 28x, 29x, 2Lx, 2Mx, 44x, 45x, 46x, 4Lx,
4Mx, 4Px, 4Qx, 4Rx, 4Tx
R
**
42T1852
(continued)
Lenovo 3000 V100 and V200
95
Parts list
No.
16
FRU
FRU no.
RoHS
ID
CRU
ID
SATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm
v 0763-27x, 29x, 43x, 44x, 46x, 64x, 68x, A2x, A6x, A8x, G2x, J9x, 2Cx, 2Dx, 2Ex, 2Fx,
3Cx, 3Dx, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 6Cx, 6Fx, 4Rx, 4Sx, 4Vx, 4Xx, 4Zx, 5Zx
HGST
27R2385
R
**
Toshiba
27R2393
R
**
SATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm,
Fujitsu
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 3Cx, 3Dx, 5Cx, 5Dx, 5Gx,
5Hx, 5Jx, 6Cx, 6Fx, 4Rx, 4Sx, 4Vx, 4Xx, 4Zx, 5Zx
42T1807
R
**
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm,
Toshiba
v 0763-2Hx, 2Qx, 2Rx, 3Hx, 4Ax, 4Cx, 5Bx, 6Hx, 7Dx,
7Ex, 7Gx, 8Cx, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 3Nx,
4Jx, 4Kx, 4Nx, 4Ux, 5Mx, 5Nx, 5Qx, 5Rx, 5Sx, 5Ux,
5Wx, 6Jx, 6Kx
42T1815
R
**
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm,
Fujitsu
v 0763-2Hx, 2Qx, 2Rx, 3Hx, 4Ax, 4Cx, 5Bx, 6Hx, 7Dx,
7Ex, 7Gx, 8Cx, 2Lx, 2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 3Nx,
4Jx, 4Kx, 4Nx, 4Ux, 5Mx, 5Nx, 5Qx, 5Rx, 5Sx, 5Ux,
5Wx, 6Jx, 6Kx
v 0764-24x, 27x, 2Ax, 32x, 42x, 43x, 47x, 48x, 4Ax, 4Cx,
4Ex, 4Fx, 4Jx, 4Nx, 4Ux, 4Zx
42T1809
R
**
SATA hard disk drive, 120 GB, 9.5 mm, 5,400 rpm
v 0764-24x, 27x, 2Ax, 32x, 42x, 43x, 47x, 48x, 4Ax, 4Cx, 4Ex, 4Fx, 4Jx, 4Nx, 4Ux, 4Zx
HGST
42T1848
R
**
Seagate
42T1853
R
**
HGST
42T1849
R
**
Seagate
42T1854
R
**
Hard disk drive slot cover for MT 0763
41W6380
R
*
Hard disk drive slot cover for MT 0764
41R5807
R
*
DIMM slot cover for MT 0763
41W6379
R
*
DIMM slot cover for MT 0764
41R5806
R
*
256-MB DDR2-667 SDRAM SO-DIMM (PC2-5300)
cardOP
v 0763-B7x, G7x
40Y8401
R
**
SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm
v 0764-25x, 2Bx, 2Cx, 2Dx, 49x, 4Bx, 4Dx, 4Gx, 4Hx, 4Kx
17
18
19
(continued)
96
MT 0763 and 0764
Parts list
No.
RoHS
ID
CRU
ID
512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300)
40Y8402
cardOP
v 0763-22x, 23x, 25x, 26x, 27x, 33x, 34x, 36x, 38x, 46x,
49x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, 83x,
84x, 85x, 86x, 88x, 89x, 93x, 97x, 99x, A2x, A3x, A4x,
A5x, A6x, A8x, B3x, C2x, C3x, C4x, C5x, C6x, C7x,
C8x, C9x, D5x, D9x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,
E9x, F3x, G2x, G3x, G9x, J3x, J5x, J7x, J8x, J9x, 2Cx,
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Ax,
3Ex, 3Fx, 3Gx, 3Hx, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx,
6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Ax, 7Bx, 7Cx,
7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx,
2Mx, 2Ux, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx,
4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx,
5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx, 5Yx,
5Zx, 6Jx, 6Kx
v 0764-22x, 23x, 24x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Lx, 2Mx, 32x, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x,
4Ax, 4Bx, 4Cx, 4Dx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx,
4Tx, 4Zx
R
**
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) cardOP 40Y8403
v 0763-29x, 43x, 44x, 3Cx, 3Dx, 4Cx, 2Vx
v 0764-2Dx, 4Ex, 4Fx, 4Jx, 4Ux
R
**
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) cardOP 40Y8404
v 0764-25x, 4Gx, 4Hx, 4Kx
R
**
20
Backup battery
92P1228
R
N
21
Fan for MT 0763
41W6376
R
N
Fan for MT 0764
41R5809
R
N
Battery pack, Li-ion (3 cell), Sony
v 0763-22x, 23x, 25x, 26x, 33x, 46x, 59x, 65x, 84x, 89x,
97x, 99x, A4x, B3x, C3x, C5x, C7x, C8x, C9x, D5x,
D9x, E2x, E3x, E5x, E6x, E7x, E9x, F3x, G3x, J7x, J8x,
J9x
92P1218
R
*
Battery pack, Li-ion (3 cell), Sanyo
92P1216
v 0763-22x, 23x, 25x, 26x, 33x, 46x, 59x, 65x, 84x, 89x,
97x, 99x, A4x, B3x, C3x, C5x, C7x, C8x, C9x, D5x,
D9x, E2x, E3x, E5x, E6x, E7x, E9x, F3x, G3x, J7x, J8x,
J9x, 2Gx, 2Px, 3Ax, 3Ex, 3Fx, 3Gx, 4Bx, 4Dx, 4Ex, 4Hx,
5Cx, 5Dx, 5Jx, 6Ex, 7Cx, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx, 2Xx,
3Lx, 3Mx, 3Nx
R
*
Battery pack, Li-ion (3 cell), Sanyo
v 0764-22x, 2Bx, 32x, 44x, 4Px, 4Lx
42T4508
R
*
Battery pack, Li-ion (3 cell), Panasonic
42T5220
v 0763-2Gx, 2Px, 3Ax, 3Ex, 3Fx, 3Gx, 4Bx, 4Dx, 4Ex,
4Hx, 5Cx, 5Dx, 5Jx, 6Ex, 7Cx, 8Bx, 8Cx, 8Dx, 8Ex, 2Lx,
2Xx, 3Lx, 3Mx, 3Nx
v 0764-22x, 2Bx, 32x, 44x, 4Px, 4Lx
R
*
19
22
FRU
FRU no.
(continued)
Lenovo 3000 V100 and V200
97
Parts list
No.
22
23
FRU
FRU no.
RoHS
ID
CRU
ID
Battery pack, Li-ion (6 cell), Sony
v 0763-27x, 29x, 34x, 36x, 38x, 43x, 44x, 49x, 62x, 64x,
66x, 68x, 69x, 77x, 82x, 83x, 85x, 86x, 88x, 93x, A2x,
A3x, A5x, A6x, A8x, B7x, C2x, C4x, C6x, E4x, E8x,
G2x, G7x, G9x, J3x, J5x
92P1222
R
*
Battery pack, Li-ion (6 cell), Sanyo
92P1220
v 0763-27x, 29x, 34x, 36x, 38x, 43x, 44x, 49x, 62x, 64x,
66x, 68x, 69x, 77x, 82x, 83x, 85x, 86x, 88x, 93x, A2x,
A3x, A5x, A6x, A8x, B7x, C2x, C4x, C6x, E4x, E8x,
G2x, G7x, G9x, J3x, J5x, 2Cx, 2Dx, 2Ex, 2Fx, 2Hx, 2Qx,
2Rx, 2Sx, 3Cx, 3Dx, 3Hx, 4Ax, 4Cx, 4Fx, 4Gx, 5Ax,
5Bx, 5Ex, 5Fx, 5Gx, 5Hx, 6Ax, 6Bx, 6Cx 6Dx, 6Fx, 6Hx,
7Ax, 7Bx, 7Dx, 7Ex, 7Fx, 7Gx, 8Ax, 2Mx, 2Ux, 2Vx,
2Wx, 4Jx 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx,
4Zx, 5Kx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux,
5Wx, 5Xx, 5Yx, 5Zx, 6Jx, 6Kx
R
*
Battery pack, Li-ion (6 cell), Sanyo
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Dx,
2Lx, 2Mx, 42x, 43x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx,
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Mx, 4Nx,
4Qx, 4Rx, 4Tx, 4Ux, 4Zx
42T4509
R
*
Battery pack, Li-ion (6 cell), Panasonic
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Hx, 2Qx, 2Rx, 3Cx, 3Dx,
3Hx, 4Ax, 4Cx, 4Fx, 4Gx, 5Ax, 5Bx, 5Ex, 5Fx, 5Gx,
5Hx, 6Ax, 6Bx, 6Cx 6Dx, 6Fx, 6Hx, 7Ax, 7Bx, 7Dx,
7Ex, 7Fx, 7Gx, 8Ax, 2Mx, 2Ux, 2Vx, 2Wx, 4Jx, 4Kx,
4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Xx,
5Yx, 5Zx, 6Jx, 6Kx
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Dx,
2Lx, 2Mx, 42x, 43x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx,
4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Mx, 4Nx,
4Qx, 4Rx, 4Tx, 4Ux, 4Zx
42T5222
R
*
Heat sink assembly for MT 0763
41W2639
R
N
Heat sink assembly for MT 0764
41R5804
R
N
(continued)
98
MT 0763 and 0764
Parts list
No.
24
FRU
FRU no.
RoHS
ID
CRU
ID
CPU assembly, Intel Core Solo processor T1300 (1.66
GHz) (667 MHz)
v 0763-33x, 34x, 36x, 59x, 77x, 93x, 97x, 99x, B3x, B7x,
D9x, F3x
41W1140
R
N
CPU assembly, Intel Core Duo processor T2050 (1.6
GHz) (667 MHz)
v 0763-J8x
41W1461
R
N
CPU assembly, Intel Core Duo processor T2250 (1.73
GHz) (667 MHz)
v 0763-J9x, 4Nx, 5Px, 5Qx, 5Rx
41W1463
R
N
CPU assembly, Intel Core Duo processor T2300 (1.66
41W1132
GHz)
v 0763-23x, 25x, 27x, 38x, 62x, 64x, 65x, 69x, 82x, 83x,
85x, 89x, A3x, A4x, A5x, C2x, C3x, C4x, C5x, C6x,
C7x, C8x, C9x, D5x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,
E9x, G2x, G3x, G7x, G9x, J3x, J5x, J7x
R
N
CPU assembly, Intel Core Duo processor T2350 (1.86
GHz)
v 0763-4Jx, 5Kx, 6Kx
42W7660
R
N
CPU assembly, Intel Core Duo processor T2300E (1.66
41W1329
GHz)
v 0763-23x, 25x, 27x, 38x, 62x, 64x, 65x, 69x, 82x, 83x,
85x, 89x, A3x, A4x, A5x, C2x, C3x, C4x, C5x, C6x,
C7x, C8x, C9x, D5x, E2x, E3x, E4x, E5x, E6x, E7x, E8x,
E9x, G2x, G3x, G7x, G9x, J3x, J5x, J7x
R
N
CPU assembly, Intel Core Duo processor T2400 (1.83
GHz)
v 0763-22x, 26x, 43x, 46x, 49x, 66x, 84x, 86x, 88x
41W1134
R
N
CPU assembly, Intel Core Duo processor T2500 (2.0
GHz)
v 0763-29x, 44x, 68x, A2x, A6x, A8x
41W1136
R
N
CPU assembly, Intel Core 2 Duo processor T5200 (1.6
GHz)
v 0763- 2Lx, 2Mx, 2Xx, 4Vx, 4Xx, 4Zx, 5Mx, 5Nx, 5Tx.
5Ux. 5Wx
41W1465
R
N
CPU assembly, Intel Core 2 Duo processor T5300 (1.73
GHz)
v 0763- 4Kx, 6Jx
41R7755
R
N
CPU assembly, Intel Core 2 Duo processor T5500 (1.66
41W1409
GHz)
v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 3Cx,3Ex, 3Fx, 3Gx, 3Hx,
4Bx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 6Ax, 6Bx, 7Ax, 7Bx,
8Ax, 8Bx, 3Lx, 5Xx, 5Yx, 5Zx
R
N
CPU assembly, Intel Core 2 Duo processor T5600 (1.83
GHz)
v 0763-2Px, 2Qx, 2Sx, 3Ax, 5Ax, 5Bx, 5Cx, 5Ex, 5Fx,
5Gx, 5Hx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx, 7Fx, 7Gx,
8Cx, 8Dx, 8Ex, 3Mx, 4Rx, 4Sx, 4Tx, 4Ux, 4Yx
R
N
41W1410
(continued)
Lenovo 3000 V100 and V200
99
Parts list
No.
FRU
FRU no.
RoHS
ID
CRU
ID
CPU assembly, Intel Core 2 Duo processor T7100 (1.83
GHz)
v 0764-22x, 23x, 26x, 28x, 29x, 2Bx, 2Lx, 2Mx, 42x, 43x,
44x, 45x, 46x, 4Cx, 4Dx, 4Ex, 4Fx, 4Jx, 4Lx, 4Mx, 4Px,
4Qx, 4Rx, 4Tx, 4Ux
42W7654
R
N
CPU assembly, Intel Core 2 Duo processor T7200 (2.0
GHz)
v 0763-2Hx, 2Rx, 3Dx, 4Ax, 4Cx, 5Jx, 5Dx, 7Dx, 7Ex,
2Ux, 2Vx, 2Wx, 3Nx, 5Sx
41W1411
R
N
CPU assembly, Intel Core 2 Duo processor T7300 (2.0
GHz)
v 0764-24x, 27x, 2Ax, 2Cx, 2Dx, 32x, 47x, 48x, 49x, 4Ax,
4Nx, 4Zx
42W7655
R
N
CPU assembly, Intel Core 2 Duo processor T7500 (2.20
GHz)
v 0764-25x, 4Gx, 4Bx, 4Hx, 4Kx
42W7656
R
N
25
ExpressCard slot
41W6378
R
N
—
Label kit for MT 0763
41W6384
R
N
—
Label kit for MT 0764
41R5811
R
N
—
Blank bezel for ExpressCard slot and 5-1 Digital Media
Reader
42W2200
R
*
24
100
MT 0763 and 0764
Parts list
LCD FRUs
1
2
8
7
3
4
6
5
Lenovo 3000 V100 and V200
101
Parts list
12.1-in. WXGA TFT
No.
102
MT 0763 and 0764
FRU
FRU no.
RoHS
ID
CRU
ID
1
LCD front bezel
41W6369
R
N
2
LCD panel, 12.1-in. WXGA AG, Samsung
13N7184
R
N
LCD panel, 12.1-in. WXGA AG, AUO
13N7182
R
N
LCD panel, 12.1-in. WXGA AG, CMO
13N7180
R
N
3
Inverter card
41W1322
R
N
4
LCD cable assembly, for no-camera
91P7032
v 0763-23x, 25x, 27x, 29x, 33x, 43x, 49x, 59x, 65x, 69x,
77x, 83x, 85x, 93x, 97x, 99x, A3x, A5x, B3x, B7x, C3x,
C5x, C7x, C9x, D5x, D9x, E3x, E5x, E7x, E9x, F3x,
G3x, G7x, G9x, J3x, J5x, J7x, 3Ax, 3Ex, 3Gx, 3Hx, 4Ax,
4Bx, 5Ax, 5Bx, 6Ax, 6Bx, 7Ax, 7Bx, 8Ax, 8Ex, 5Xx, 5Yx
v 0764-22x, 42x, 43x, 44x, 45x, 46x, 4Ax, 4Lx, 4Px, 4Qx,
4Rx
R
N
LCD cable assembly, for camera
91P7033
v 0763-22x, 26x, 34x, 36x, 38x, 44x, 46x, 62x, 64x, 66x,
68x, 82x, 84x, 86x, 88x, 89x, A2x, A4x, A6x, A8x, C2x,
C4x, C6x, C8x, E2x, E4x, E6x, E8x, G2x, J8x, J9x, 2Cx,
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Cx,
3Dx, 3Fx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx,
7Dx, 7Ex, 7Fx, 7Gx, 8Bx, 8Cx, 8Dx, 2Lx, 2Mx, 2Ux,
2Vx, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx,
4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx,
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Dx, 2Lx, 2Mx, 32x, 47x, 48x, 49x, 4Bx, 4Cx, 4Dx, 4Ex,
4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux, 4Zx
R
N
5
LCD rear cover
41W2638
R
N
6
Antenna assembly for MT 0763
91P7034
R
N
Antenna assembly for MT 0764
41R5800
R
N
7
Hinges
41W6370
R
N
8
Integrated camera
41W1331
v 0763-22x, 26x, 34x, 36x, 38x, 44x, 46x, 62x, 64x, 66x,
68x, 82x, 84x, 86x, 88x, 89x, A2x, A4x, A6x, A8x, C2x,
C4x, C6x, C8x, E2x, E4x, E6x, E8x, G2x, J8x, J9x, 2Cx,
2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Px, 2Qx, 2Rx, 2Sx, 3Cx,
3Dx, 3Fx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 6Cx, 6Dx, 6Ex, 6Fx, 6Hx, 7Cx,
7Dx, 7Ex, 7Fx, 7Gx, 8Bx, 8Cx, 8Dx, 2Lx, 2Mx, 2Ux,
2Vx, 2Wx, 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx,
4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx,
5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Wx, 5Zx, 6Jx, 6Kx
v 0764-23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx,
2Dx, 2Lx, 2Mx, 32x, 47x, 48x, 49x, 4Bx, 4Cx, 4Dx, 4Ex,
4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Nx, 4Tx, 4Ux, 4Zx
R
N
Parts list
Keyboard
Keyboard for MT 0763
Language
P/N
(NMB)
P/N
RoHS
(Chicony) ID
CRU
ID
Arabic
39T7368
39T7432
N
Belgian
39T7365
39T7429
Chinese, Traditional
39T7379
39T7443
Czech
39T7373
39T7437
Danish
39T7362
39T7426
Dutch
39T7359
39T7423
English, U.K.
39T7357
39T7421
English, U.S.
39T7353
39T7417
English, U.S. (International, with a Euro symbol)
39T7383
39T7447
Finnish, Swedish
39T7360
39T7424
French, Canadian (058)
39T7355
39T7419
French, Canadian, Acnor
39T7354
39T7418
French, European
39T7358
39T7422
German
39T7356
39T7420
Greek
39T7375
39T7439
Hebrew
39T7370
39T7434
Hungarian
39T7374
39T7438
Iceland
42T3006
—
Italian
39T7363
39T7427
Japanese
39T7378
39T7442
Korean
39T7380
39T7444
Norwegian
39T7361
39T7425
Polish
39T7371
39T7435
Portuguese
39T7367
39T7431
Portuguese, Brazilian
39T7384
39T7448
Russian
39T7369
39T7433
Slovak
39T7377
39T7441
Slovenian
39T7376
39T7440
Spanish, European
39T7364
39T7428
Spanish, Latin American
39T7381
39T7445
Swiss
39T7366
39T7430
Thai
39T7382
39T7446
Turkish
39T7372
39T7436
R
Lenovo 3000 V100 and V200
103
Parts list
Keyboard for MT 0764
104
MT 0763 and 0764
Language
P/N
(NMB)
P/N
RoHS
(Chicony) ID
CRU
ID
Arabic
42T3353
42T3418
N
Belgian
42T3350
42T3415
Chinese, Traditional
42T3364
42T3429
Czech
42T3358
42T3423
Danish
42T3347
42T3412
Dutch
42T3344
42T3409
English, U.K.
42T3342
42T3407
English, U.S.
42T3338
42T3403
English, U.S. (International, with a Euro symbol)
42T3368
42T3433
Finnish, Swedish
42T3345
42T3410
French, Canadian (058)
42T3340
42T3405
French, Canadian, Acnor
42T3339
42T3404
French, European
42T3343
42T3408
German
42T3341
42T3406
Greek
42T3360
42T3425
Hebrew
42T3355
42T3420
Hungarian
42T3359
42T3424
Iceland
42T3370
—
Italian
42T3348
42T3413
Japanese
42T3363
42T3428
Korean
42T3365
42T3430
Norwegian
42T3346
42T3411
Polish
42T3356
42T3421
Portuguese
42T3352
42T3417
Portuguese, Brazilian
42T3369
42T3434
Russian
42T3354
42T3419
Slovak
42T3362
42T3427
Slovenian
42T3361
42T3426
Spanish, European
42T3349
42T3414
Spanish, Latin American
42T3366
42T3431
Swiss
42T3351
42T3416
Thai
42T3367
42T3432
Turkish
42T3357
42T3422
R
Parts list
Recovery discs
Windows XP Professional CDs
Windows XP Professional is preinstalled as the operating system in the following
models:
v 0763-22x, 23x, 27x, 29x, 43x, 44x, 46x, 49x, 84x, 88x, 89x, A3x, A6x, B3x, C4x, D5x,
E5x, E8x, F3x, G2x, J3x, J5x, J7x, 2Dx, 2Fx, 2Hx, 2Rx, 3Dx, 3Fx, 3Hx, 4Ax, 4Cx,
4Ex, 4Fx, 4Hx, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Gx, 5Jx, 6Ax, 7Ax, 7Cx, 7Dx, 7Ex, 7Fx,
8Ax, 8Cx, 8Ex
Language
P/N
RoHS
ID
CRU
ID
Arabic
43T3842
R
*
Chinese, Simplified
43T3835
Chinese, Traditional
43T3836
Chinese, Traditional (Hong Kong S.A.R.)
43T3837
Czech
43T3841
Danish
43T3831
Dutch
43T3834
English, (UD) U.K. with disabled modem and WLAN
43T3824
English, U.S., U.K. with enabled modem and WLAN
43T3823
Finnish
43T3832
French
43T3825
German
43T3826
Greek
43T3846
Hebrew, English enabled
43T3839
Hungarian
43T3845
Italian
43T3828
Japanese
43T3838
Korean
43T3847
Norwegian
43T3833
Polish
43T3840
Portuguese, Brazilian
43T3829
Russian
43T3843
Russian, English Enabled
43T3849
Spanish
43T3827
Slovenian
43T3848
Swedish
43T3830
Turkish
43T3844
Lenovo 3000 V100 and V200
105
Parts list
Windows XP Home Edition CDs
Windows XP Home Edition is preinstalled as the operating system in the following
models:
v 0763-25x, 26x, 33x, 34x, 36x, 38x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, 83x,
85x, 86x, 93x, 99x, A2x, A4x, A5x, A8x, B7x, C2x, C5x, C6x, C7x, C9x, D9x, E3x,
E4x, E6x, E7x, E9x, G7x, G9x, J8x, J9x, 2Cx, 2Ex, 2Gx, 2Px, 2Qx, 2Sx, 3Ax, 3Cx,
3Ex, 3Gx, 4Bx, 4Dx, 4Gx, 5Fx, 5Hx, 6Bx, 6Cx, 6Ex, 6Fx, 6Hx, 7Bx, 7Gx, 8Bx, 8Dx
106
MT 0763 and 0764
Language
P/N
RoHS
ID
CRU
ID
Arabic
43T4058
R
*
Chinese, Simplified
43T4051
Chinese, Traditional
43T4052
Chinese, Traditional (Hong Kong S.A.R.)
43T4053
Czech
43T4057
Danish
43T4047
Dutch
43T4050
English, (UD) U.K. with disabled modem and WLAN
43T4040
English, U.S., U.K. with enabled modem and WLAN
43T4039
Finnish
43T4048
French
43T4041
German
43T4042
Greek
43T4062
Hebrew
43T4065
Hebrew, English enabled
43T4055
Hungarian
43T4061
Italian
43T4044
Japanese
43T4054
Korean
43T4063
Norwegian
43T4049
Polish
43T4056
Portuguese, Brazilian
43T4045
Russian
43T4059
Russian, English enabled
43T4064
Spanish
43T4043
Swedish
43T4046
Turkish
43T4060
Parts list
Windows Vista Home Premium (32 bit) DVDs for MT 0763
Windows Vista Home Premium is preinstalled as the operating system in the
following models:
v 0763-2Lx, 3Nx, 4Jx, 4Nx, 4Vx, 4Zx, 5Wx, 5Xx, 5Zz
Language
P/N
RoHS
ID
CRU
ID
Chinese, Traditional
43T7173
R
*
Chinese, Traditional (Hong Kong S.A.R.)
43T7174
Czech
43T7166
Danish
43T7909
Dutch
43T7165
English, (UD) U.K. with disabled modem and WLAN
43T7155
English, U.S., U.K. with enabled modem and WLAN
43T7154
Finnish
43T7167
French
43T7156
German
43T7157
Greek
43T7172
Hebrew
43T7176
Hungarian
43T7171
Italian
43T7160
Japanese
43T7161
Korean
43T7175
Norwegian
43T7905
Polish
43T7168
Portuguese, Brazilian
43T7159
Russian
43T7169
Russian, English enabled
43T7821
Slovenian
43T7932
Spanish
43T7158
Swedish
43T7907
Turkish
43T7170
Lenovo 3000 V100 and V200
107
Parts list
Windows Vista Home Premium (32 bit) DVDs for MT 0764
Windows Vista Home Premium is preinstalled as the operating system in the
following models:
v 0764-24x, 2Ax, 2Bx, 43x, 46x, 49x, 4Dx, 4Rx
108
MT 0763 and 0764
Language
P/N
RoHS
ID
CRU
ID
Bulgarian
44Y0027
R
*
Chinese, Simplified
44Y0004
Chinese, Traditional
44Y0011
Chinese, Traditional (Hong Kong S.A.R.)
44Y0014
Croatian
44Y0028
Czech
44Y0020
Danish
44Y0012
Dutch
44Y0016
English, (UD) U.K. with disabled modem and WLAN
44Y0001
English, U.S., U.K. with enabled modem and WLAN
44Y0000
Finnish
44Y0013
French
44Y0005
German
44Y0006
Greek
44Y0022
Hebrew
44Y0007
Hungarian
44Y0023
Italian
44Y0008
Japanese
44Y0009
Korean
44Y0015
Norwegian
44Y0017
Polish
44Y0021
Portuguese
44Y0024
Portuguese, Brazilian
44Y0003
Romanian
44Y0029
Russian
44Y0018
Russian, English enabled
44Y0002
Serbian-Latin
44Y0030
Slovak
44Y0031
Slovenian
44Y0025
Spanish
44Y0010
Swedish
44Y0019
Turkish
44Y0026
Ukrainian
44Y0032
Parts list
Windows Vista Home Basic (32 bit) DVDs for MT 0763
Windows Vista Home Basic is preinstalled as the operating system in the following
models:
v 0763-2Xx, 3Lx, 4Sx, 4Tx, 4Ux, 4Xx, 4Yx, 5Kx, 5Px, 5Sx, 5Tx
Language
P/N
RoHS
ID
CRU
ID
Chinese, Traditional
43T7127
R
*
Chinese, Traditional (Hong Kong S.A.R.)
43T7128
Czech
43T7120
Danish
43T7903
Dutch
43T7119
English, (UD) U.K. with disabled modem and WLAN
43T7109
English, U.S., U.K. with enabled modem and WLAN
43T7108
Finnish
43T7121
French
43T7110
German
43T7111
Greek
43T7126
Hebrew
43T7130
Hungarian
43T7125
Italian
43T7114
Japanese
43T7115
Korean
43T7129
Norwegian
43T7899
Polish
43T7122
Portuguese, Brazilian
43T7113
Russian
43T7123
Russian, English enabled
43T7820
Slovenian
43T7931
Spanish
43T7112
Swedish
43T7901
Turkish
43T7124
Lenovo 3000 V100 and V200
109
Parts list
Windows Vista Home Basic (32 bit) DVDs for MT 0764
Windows Vista Home Basic is preinstalled as the operating system in the following
models:
v 0764-22x, 44x, 48x, 4Cx, 4Fx, 4Hx, 4Jx, 4Lx, 4Px, 4Ux
110
MT 0763 and 0764
Language
P/N
RoHS
ID
CRU
ID
Chinese, Simplified
44Y0069
R
*
Chinese, Traditional
44Y0076
Chinese, Traditional (Hong Kong S.A.R.)
44Y0079
Czech
44Y0085
Danish
44Y0077
Dutch
44Y0081
English, (UD) U.K. with disabled modem and WLAN
44Y0066
English, U.S., U.K. with enabled modem and WLAN
44Y0065
Finnish
44Y0078
French
44Y0070
German
44Y0071
Greek
44Y0087
Hebrew
44Y0072
Hungarian
44Y0088
Italian
44Y0073
Japanese
44Y0074
Korean
44Y0080
Norwegian
44Y0082
Polish
44Y0086
Portuguese, Brazilian
44Y0068
Russian
44Y0083
Russian, English enabled
44Y0067
Slovenian
44Y0089
Spanish
44Y0075
Swedish
44Y0084
Turkish
44Y0090
Parts list
Windows Vista Business (32 bit) DVDs for MT 0763
Windows Vista Business is preinstalled as the operating system in the following
models:
v 0763-2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 4Kx, 4Rx, 5Mx, 5Nx, 5Qx, 5Rx, 5Ux, 5Yx, 6Jx,
6Kx
Language
P/N
RoHS
ID
CRU
ID
Chinese, Traditional
43T7081
R
*
Chinese, Traditional (Hong Kong S.A.R.)
43T7082
Czech
43T7074
Danish
43T7897
Dutch
43T7073
English, (UD) U.K. with disabled modem and WLAN
43T7063
English, U.S., U.K. with enabled modem and WLAN
43T7062
Finnish
43T7075
French
43T7064
German
43T7065
Greek
43T7080
Hebrew
43T7084
Hungarian
43T7079
Italian
43T7068
Japanese
43T7069
Korean
43T7083
Norwegian
43T7893
Polish
43T7076
Portuguese, Brazilian
43T7067
Russian
43T7077
Russian, English enabled
43T7818
Slovenian
43T7929
Spanish
43T7066
Swedish
43T7895
Turkish
43T7078
Lenovo 3000 V100 and V200
111
Parts list
Windows Vista Business (32 bit) DVDs for MT 0764
Windows Vista Business is preinstalled as the operating system in the following
models:
v 0764-23x 26x, 27x, 28x, 29x, 2Cx, 2Lx, 2Mx, 32x, 42x, 45x, 47x, 4Ax, 4Bx, 4Ex,
4Mx, 4Nx, 4Qx, 4Tx, 4Zx
112
MT 0763 and 0764
Language
P/N
RoHS
ID
CRU
ID
Bulgarian
44Y0059
R
*
Chinese, Simplified
44Y0037
Chinese, Traditional
44Y0043
Chinese, Traditional (Hong Kong S.A.R.)
44Y0046
Croatian
44Y0060
Czech
44Y0052
Danish
44Y0044
Dutch
44Y0048
English, (UD) U.K. with disabled modem and WLAN
44Y0034
English, U.S., U.K. with enabled modem and WLAN
44Y0033
Finnish
44Y0045
French
44Y0038
German
44Y0039
Greek
44Y0054
Hungarian
44Y0055
Italian
44Y0040
Japanese
44Y0041
Korean
44Y0047
Norwegian
44Y0049
Polish
44Y0053
Portuguese
44Y0056
Portuguese, Brazilian
44Y0036
Romanian
44Y0061
Russian
44Y0050
Russian, English enabled
44Y0035
Serbian-Latin
44Y0062
Slovak
44Y0063
Slovenian
44Y0057
Spanish
44Y0042
Swedish
44Y0051
Turkish
44Y0058
Ukrainian
44Y0064
Parts list
Windows Vista Ultimate (32 bit) DVDs
Windows Vista Ultimate is preinstalled as the operating system in the following
models:
v 0764-25x, 2Dx, 4Gx, 4Kx
Language
P/N
RoHS
ID
CRU
ID
Chinese, Simplified
44Y0095
R
*
Chinese, Traditional
44Y0101
Chinese, Traditional (Hong Kong S.A.R.)
44Y0104
Czech
44Y0110
Danish
44Y0102
Dutch
44Y0106
English, (UD) U.K. with disabled modem and WLAN
44Y0092
English, U.S., U.K. with enabled modem and WLAN
44Y0091
Finnish
44Y0103
French
44Y0096
German
44Y0097
Greek
44Y0112
Hungarian
44Y0113
Italian
44Y0098
Japanese
44Y0099
Korean
44Y0105
Norwegian
44Y0107
Polish
44Y0111
Portuguese, Brazilian
44Y0094
Russian
44Y0108
Russian, English enabled
44Y0093
Spanish
44Y0100
Slovenian
44Y0114
Swedish
44Y0109
Turkish
44Y0115
Lenovo 3000 V100 and V200
113
Parts list
Corel software CDs
Language
P/N
RoHS
ID
CRU
ID
English, U.S.
41X0440
R
*
French
41X0443
Japanese
41X0608
Portuguese, Brazilian
41X0449
Spanish
41X0446
Miscellaneous parts
114
MT 0763 and 0764
FRU
P/N
RoHS
ID
CRU
ID
Screw kit, (including nylon-coated screws) for MT 0763:
v M2 × 2 mm (silver), pan-head (4)
v M2 × 2.5 mm (silver), pan-head (13)
v M2 × 3 mm (silver), pan-head (6)
v M2 × 4 mm (silver), pan-head (13)
v M2.5 × 5 mm (black), pan-head (10)
v M2.5 × 5 mm (silver), pan-head (20)
v M2.5 × 7 mm (black), pan-head (1)
v M2.5 × 13 mm (silver), pan-head (2)
v M3 × 2.8 mm (silver), pan-head (4)
v Hex stud (2)
v Screw cap rubber (6)
41W6383
R
N
Screw kit, (including nylon-coated screws) for MT 0764:
v M2 x 4 mm (silver), pan-head (2)
v M2.5 x 5 mm (silver), pan-head (20)
v M2.5 x 13 mm (silver), pan-head (2)
41R5810
R
N
System miscellaneous parts:
v Bracket, digital media reader
v Bracket, fingerprint reader
v Bracket, optical drive
v Bracket, touch pad
v ExpressCard slot blank bezel
v Digital media reader blank bezel
v Rubber foot
v Screw cap rubber
41W6382
R
N
Cable miscellaneous parts for MT 0763
91P7035
R
N
Cable miscellaneous parts for MT 0764:
v MDC cable
v Fingerprint reader cable
v Launch board cable
v Bluetooth cable
v Digital media reader FCC
41R5812
R
N
Parts list
AC adapters
FRU
P/N
RoHS
ID
CRU
ID
2-pin (65 W, 20 V) adapter (models xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) OP
Delta
92P1155
R
*
Lite-On
92P1159
R
*
Astec
92P1214
R
*
3-pin (65W, 20 V) adapter (models xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxR, xxT, xxV)
OP
Delta
92P1153
R
*
Lite-On
92P1157
R
*
Astec
92P1212
R
*
Common parts list
Tools
Tool
P/N
Triconnector wrap plug
72X8546
Audio wrap cable
66G5180
USB parallel test cable
05K2580
Screwdriver kit
95F3598
Mini PC tool set
00P7033
1/4" drive spinner handle
1650840
1/4" Sq. to 1/4" hex torx adapter
93F2838
TR7-TR-10 tamper resistant torx bits
00P6967
Removal tool antenna RF connector
08K7159
PCI-Express/USB wrap card
27K9813
CE Utility Diskette for Lenovo 3000 notebooks
—
Note: Download the file from the following Web site: http://www.lenovo.com/
spm
Lenovo 3000 V100 and V200
115
Parts list
Power cords
A Lenovo 3000 power cord for a specific country or region is usually available only
in that country or region:
For 2-pin power cords:
Region
P/N
(Longwell)
P/N (Volex) RoHS
ID
CRU
ID
Argentina
42T5020
42T5105
*
Brazil
42T5026
42T5111
Canada, U.S.
42T5008
42T5093
Japan
42T5014
42T5099
Region
P/N
(Longwell)
P/N (Volex) RoHS
ID
CRU
ID
Australia, New Zealand
42T5050
42T5135
*
Denmark
42T5041
42T5126
Europe
42T5029
42T5114
Hong Kong S.A.R. of China, U.K.
42T5035
42T5120
India
42T5083
42T5168
Israel
42T5062
42T5147
Italy
42T5047
42T5132
Korea
42T5077
42T5162
South Africa
42T5056
42T5141
Switzerland
42T5044
42T5129
Thailand, Taiwan
42T5004
42T5089
R
For 3-pin power cords:
116
MT 0763 and 0764
R
Notices
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
Lenovo 3000 V100 and V200
117
Notices
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries
or both:
Lenovo
Lenovo Care
Rescue and Recovery
ThinkPad
The following terms are trademarks of the International Business Machines
Corporation in the United States, other countries, or both:
IBM (used under license)
The following terms are trademarks of Microsoft Corporation in the United States,
other countries, or both:
Microsoft®
Windows®
Windows Vista
The following are trademarks of Intel Corporation or its subsidiaries in the United
States, other countries, or both:
Intel®
Intel® Core™
Intel® Core™ Duo
Intel® Core™ Solo
Intel® Core™ 2 Duo
Other company, product, or service names may be the trademarks or service marks
of others.
118
MT 0763 and 0764
Trademarks
Lenovo 3000 V100 and V200
119
Part Number: 42X3554
(1P) P/N: 42X3554