Panasonic KX-TA824 Installation Manual

Panasonic KX-TA824 Installation Manual
Advanced Hybrid System
Installation Manual
Model No.
KX-TA824
Thank you for purchasing a Panasonic Advanced Hybrid System.
Please read this manual carefully before using this product and save this manual for future use.
KX-TA824: Version 3.0
Document Version: 2007-04
System Components
System Components Table
Model
Description
Main Unit
KX-TA824
Advanced Hybrid System: 3 to 8 Outside (CO) Lines, 8 to 24
Extensions
Optional Service Cards
KX-TA82461
4-Port Doorphone Card
KX-TA82470
8-Port Hybrid Extension Card
KX-TA82481
2-Port Analog CO Line and 8-Port Hybrid Extension Card
KX-TA82483
3-Port Analog CO Line and 8-Port Hybrid Extension Card
KX-TA82491
Message Expansion Card for DISA OGMs
KX-TA82492
2-Channel Voice Message Card
KX-TA82493
3-Port Caller ID Card
KX-T30865
Doorphone
Proprietary Equipment
Expandability of Outside (CO) Lines and Extensions
KX-TA824
Outside (CO) Line: 3
Extension: 8
KX-TA82483
KX-TA82481
KX-TA82470
Outside (CO) Line: 3
Outside (CO) Line: 2
Outside (CO) Line: 0
Extension: 8
Extension: 8
Extension: 8
–
–
–
–
0
8
3
16
–
–
2
8
–
–
5
16
3
8
–
–
–
–
6
16
3
8
–
–
0
8
6
24
3
8
2
8
–
–
8
24
Abbreviations in this manual
Proprietary Telephone: PT
Single Line Telephone: SLT
Direct Station Selection: DSS
Compatible Proprietary Telephones
•
KX-T7700, KX-T7300, KX-T7000, and KX-TA30800 series PTs
•
KX-T7740, KX-T7340, and KX-T7040 DSS Consoles
2
Installation Manual
Expanded
System
•
Wireless PTs such as KX-T7885, KX-TD7895, and KX-TD7896
For the equipment that can be connected to the PBX, refer to "1.2.2 System Connection Diagram".
Important Notice
Prior to connection of this product, please verify that the intended operating environment is
supported.
Satisfactory performance cannot be guaranteed for the following:
– interoperability and compatibility with all devices and systems connected to this product
– proper operation and compatibility with services provided by telecommunications
companies over connected networks
Installation Manual
3
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Clean with a damp cloth.
4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool.
5. Do not place the product on an unstable surface, as a fall may cause serious internal damage.
6. Slots and openings in the front, back and bottom of the cabinet are provided for ventilation; to
protect it from overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface while in use.
The product should never be placed near or over a radiator or other heat source. This product
should not be placed in a sealed environment unless proper ventilation is provided.
7. The product should only be connected to the type of electrical power supply specified on the
product label. If you are not sure of the type of power supply to your home, consult your dealer
or local power company.
8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded
outlet, please have one installed. Do not bypass this safety feature by tampering with the plug.
9. Do not allow anything to rest on the power cord. Do not locate this product where the power cord
may be stepped on or tripped on.
10. To reduce the risk of fire or electric shock, do not overload wall outlets and extension cords.
11. Do not insert objects of any kind into this product through its slots and openings, as they may
touch dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on or in the product.
12. To reduce the risk of electric shock, do not disassemble this product. Only qualified personnel
should service this product. Opening or removing covers may expose you to dangerous voltages
or other risks. Incorrect reassembly can cause electric shock.
13. Unplug this product from the wall outlet and have it serviced by qualified service personnel in the
following cases:
a)
b)
c)
d)
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate according to the operating instructions. Adjust only the
controls that are explained in the operating instructions. Improper adjustment of other
controls may result in damage and may require service by a qualified technician to restore
the product to normal operation.
e) If the product has been dropped or the cabinet has been damaged.
f) If product performance deteriorates.
14. Avoid using wired telephones during an electrical storm. There is a remote risk of electric shock
from lightning.
15. Do not use a telephone in the vicinity of a gas leak to report the leak.
SAVE THESE INSTRUCTIONS
4
Installation Manual
Precautions
•
•
•
Keep the unit away from heating appliances and devices that generate electrical noise such as
fluorescent lamps, motors and televisions. These noise sources can interfere with the
performance of the PBX.
This unit should be kept free of dust, moisture, high temperature (more than 40 °C [104 °F]) and
vibration, and should not be exposed to direct sunlight.
If you are having problems making calls to outside destinations, follow this procedure to test the
outside (CO) lines:
1. Disconnect the PBX from all outside (CO) lines.
2. Connect known working single line telephones (SLTs) to those outside (CO) lines.
3. Make a call to an external destination using those SLTs.
•
If a call cannot be carried out correctly, there may be a problem with the outside (CO) line that
the SLT is connected to. Contact your telephone company.
If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX
to the outside (CO) lines until it has been serviced by an authorized Panasonic Factory Service
Center.
Wipe the unit with a soft cloth. Do not clean the unit with abrasive powders or with chemical
agents such as benzene or thinner.
WARNING
•
•
•
•
•
•
THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED
SERVICE PERSONNEL.
IF DAMAGE TO THE UNIT EXPOSES ANY INTERNAL PARTS, DISCONNECT
THE POWER SUPPLY CORD IMMEDIATELY AND RETURN THE UNIT TO YOUR
DEALER.
UNPLUG THIS UNIT FROM THE AC OUTLET IF IT EMITS SMOKE, AN
ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN
CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED
AND CONTACT AN AUTHORIZED PANASONIC FACTORY SERVICE CENTER.
WHEN RELOCATING THE EQUIPMENT, FIRST DISCONNECT THE TELECOM
CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION. WHEN
THE UNIT IS INSTALLED IN THE NEW LOCATION, RECONNECT THE POWER
FIRST, AND THEN RECONNECT THE TELECOM CONNECTION.
TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE.
ENSURE THAT THE AC OUTLET IS LOCATED NEAR THE EQUIPMENT AND IS
EASILY ACCESSIBLE.
Installation Manual
5
Notice for users in California
This product contains a CR coin cell lithium battery that
contains perchlorate material—special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
6
Installation Manual
When you ship the product
Carefully pack and send it prepaid, adequately insured and preferably in the original carton.
Attach a postage-paid letter, detailing the symptom, to the outside of the carton. DO NOT send the
product to the Executive or Regional Sales offices. They are NOT equipped to make repairs.
Product Service
Panasonic Factory Service Centers for this product are listed in the Service Center Directory. Consult
your certified Panasonic dealer for detailed instructions.
For Future Reference
Please print, record, and retain the following information for future reference.
Note
The serial number of this product can be found on the label affixed to the unit. You should record
the model number and the serial number of this unit as a permanent record of your purchase to
aid in identification in the event of theft.
MODEL NO.
SERIAL NO.
DATE OF PURCHASE
NAME OF DEALER
DEALER'S ADDRESS
DEALER'S TEL. NO.
Installation Manual
7
Introduction
About the Installation Manual
This Installation Manual is designed to serve as an overall technical reference for Panasonic
Advanced Hybrid System, KX-TA824. It explains how to install the hardware and program this PBX
using KX-TA Maintenance Console.
The Installation Manual is divided into the following sections:
Section 1 System Outline
Provides general information on the PBX, including the system capacity and specifications.
Section 2 Installation
Provides detailed instructions for installing the PBX, optional service cards, and peripheral
equipment.
Section 3 Guide for KX-TA Maintenance Console
Explains how to install and use KX-TA Maintenance Console, a PC-based programming utility.
Section 4 Troubleshooting
Provides information on troubleshooting and restarting the PBX.
About the Other Manuals
The following manuals are also available:
Feature Manual
The Feature Manual explains what the PBX can do, as well as how to obtain the most of its many
features and facilities.
Programming Manual
The Programming Manual explains how to program the PBX using Panasonic proprietary
telephones (PTs) or the KX-TA Maintenance Console.
Operating Manual
The Operating Manual describes how users can access commonly used PBX features and
functions with their PTs, single line telephones (SLTs), and Direct Station Selection (DSS)
Consoles.
Trademarks
•
•
•
•
8
Installation Manual
Microsoft and Windows are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Intel and Celeron are trademarks or registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.
All other trademarks identified herein are the property of their respective owners.
Screen shots reprinted with permission from Microsoft Corporation.
F.C.C. REQUIREMENTS AND RELEVANT
INFORMATION
1. Notification to the Telephone Company
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the side of this equipment is a label that contains, among other information, a product
identifier in the following format:
•
US:AAAEQ##TXXXX
If requested, this number must be provided to the telephone company.
Installation must be performed by a qualified professional installer. If required, provide the
telephone company with the following technical information:
•
Telephone numbers to which the system will be connected
•
Make: Panasonic
•
Model: KX-TA824
•
Certification No.: found on the side of the unit
•
Ringer Equivalence No.: 0.4B
•
Facility Interface Code: 02LS2
•
Service Order Code: 9.0F
•
Required Network Interface Jack: RJ11
2. Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local telephone company. For products approved after July 23, 2001, the REN
for this product is part of the product identifier that has the following format:
•
US:AAAEQ##TXXXX
The digits represented by ## are the REN without a decimal point (e.g., 04 is a REN of 0.4). For
earlier products, the REN is separately shown on the label.
3. Incidence of Harm to the Telephone Lines
If this equipment causes harm to the telephone network, the telephone company will notify you
in advance that temporary discontinuance of service may be required. But if advance notice isn't
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
4. Changes in Telephone Company Communications Facilities, Equipment, Operations and
Procedures
The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service.
5. Trouble with this equipment
If trouble is experienced with this equipment, for repair or warranty information, please see the
attached warranty, which includes the Service Center Directory. If the equipment is causing harm
to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
Installation Manual
9
6. Connection to Party Line
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
7. Combined Use with Alarm Equipment
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualified installer.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this device.
When programming emergency numbers and/or making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before
hanging up.
2. Perform such activities in the off-peak hours, such as early morning hours or late evenings.
WARNING
The software contained in the TRS feature to allow user access to the network
must be upgraded to recognize newly established network area codes and
exchange codes as they are placed into service. Failure to upgrade the premises
PBXs or peripheral equipment to recognize the new codes as they are established
will restrict the customer and the customer's employees from gaining access to
the network and to these codes.
KEEP THE SOFTWARE UP-TO-DATE WITH THE LATEST DATA.
10
Installation Manual
Table of Contents
1
System Outline ..................................................................................... 13
1.1
1.1.1
1.2
1.2.1
1.2.2
1.3
1.3.1
1.3.2
1.3.3
2
Installation............................................................................................. 23
2.1
2.1.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
2.2.7
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
2.3.8
2.4
2.4.1
2.5
2.5.1
2.5.2
2.6
2.6.1
2.7
2.7.1
2.8
2.8.1
2.9
2.9.1
2.10
2.10.1
3
System Highlights .......................................................................................................... 14
System Highlights ............................................................................................................. 14
Basic System Construction ........................................................................................... 16
Main Unit........................................................................................................................... 16
System Connection Diagram ............................................................................................ 17
Specifications ................................................................................................................. 18
General Description .......................................................................................................... 18
Characteristics .................................................................................................................. 19
System Capacity ............................................................................................................... 20
Before Installing.............................................................................................................. 24
Before Installing ................................................................................................................ 24
Installing the Advanced Hybrid System ....................................................................... 26
Unpacking ......................................................................................................................... 26
Names and Locations ....................................................................................................... 27
Opening/Closing Covers ................................................................................................... 28
Securing Cords ................................................................................................................. 30
Connecting Frame Ground ............................................................................................... 32
Wall Mounting ................................................................................................................... 33
Installing Surge Protector ................................................................................................. 36
Installing Optional Service Cards.................................................................................. 39
Location of Optional Service Cards .................................................................................. 39
3-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82483) ....................... 40
2-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82481) ....................... 42
8-Port Hybrid Extension Card (KX-TA82470).................................................................... 45
3-Port Caller ID Card (KX-TA82493)................................................................................. 47
4-Port Doorphone Card (KX-TA82461)............................................................................. 49
Message Expansion Card for DISA OGMs (KX-TA82491) ............................................... 50
2-Channel Voice Message Card (KX-TA82492)................................................................ 52
Connecting Outside (CO) Lines..................................................................................... 54
Connecting Outside (CO) Lines ........................................................................................ 54
Connecting Extensions .................................................................................................. 55
Connecting Extensions ..................................................................................................... 55
Connecting Extensions in Parallel .................................................................................... 57
Connecting Doorphones and Door Openers................................................................ 58
Connecting Doorphones and Door Openers .................................................................... 58
Connecting Doorbell or Door Chime............................................................................. 62
Connecting Doorbell or Door Chime ................................................................................. 62
Connecting Peripherals.................................................................................................. 63
Connecting Peripherals..................................................................................................... 63
Power Failure Connections............................................................................................ 68
Power Failure Connections ............................................................................................... 68
Starting the Advanced Hybrid System.......................................................................... 69
Starting the Advanced Hybrid System .............................................................................. 69
Guide for KX-TA Maintenance Console .............................................. 73
Installation Manual
11
3.1
3.1.1
3.2
3.2.1
3.2.2
3.2.3
4
Troubleshooting.................................................................................... 83
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
5
Installing KX-TA Maintenance Console.........................................................................74
Installing KX-TA Maintenance Console on a PC ...............................................................74
Connection ......................................................................................................................76
Connection ........................................................................................................................76
Starting KX-TA Maintenance Console for the first time .....................................................79
Accessing PBX via Internal Modem ..................................................................................80
Troubleshooting ..............................................................................................................84
Installation .........................................................................................................................84
Connection ........................................................................................................................85
Operation ..........................................................................................................................86
System Restart .................................................................................................................87
System Reset with System Data Clear .............................................................................88
Appendix ............................................................................................... 89
5.1
5.1.1
Revision History..............................................................................................................90
Version 2.0 ........................................................................................................................90
Index ............................................................................................................ 91
12
Installation Manual
Section
1
System Outline
This section provides general information on the PBX,
including the system capacity and specifications.
Installation Manual
13
1.1 System Highlights
1.1
System Highlights
1.1.1
System Highlights
Built-in Voice Message (BV) (Optional voice message card required)
Built-in Voice Message (BV) allows a caller to leave a voice message in a user's personal message
area or the PBX's common message area.
Caller ID Display on SLT
The PBX can receive Caller ID information (telephone numbers and callers' names) from calls
received on outside (CO) lines. This information can be shown on the displays of SLTs that support
Caller ID as well as proprietary telephones (PTs) when receiving calls.
3-level Automated Attendant (AA)
3-level Automated Attendant (AA) service allows a caller to dial a single-digit number (Direct Inward
System Access [DISA] AA number) following the guidance of 3-level DISA outgoing messages
(OGMs), and be connected to the desired party automatically.
Station Message Detail Recording (SMDR)
The PBX (with an optional message expansion card) can automatically log up to 10 000 incoming/
outgoing outside (CO) line calls. It is possible to log the Date, Time, Dial number and Duration of each
call. The call logs can be output via the Serial Interface (RS-232C) port to a PC, printer, etc.
PC Programming
System programming settings can be accessed using a PC and the Panasonic KX-TA Maintenance
Console software as well as by using a PT.
The PBX software can be upgraded via the Serial Interface (RS-232C) port or USB port, using the
KX-TA Maintenance Console software.
Quick Setup
Basic PBX parameters such as Automatic Configuration for Outside (CO) Line Type, Country Setting
can be programmed the first time the PBX is accessed with a PC using the KX-TA Maintenance
Console software.
Call Waiting Caller ID
Call Waiting Caller ID allows the user to see the name or telephone number of a second caller during
a conversation.
Local Carrier-based Voice Mail Service
Local carrier-based voice mail service allows the user to receive remote voice mail service from the
telephone company to record caller messages when calls cannot be answered.
Wireless Proprietary Telephones (PTs)
Wireless PTs such as the KX-T7885, KX-TD7895, and KX-TD7896 give a user the freedom to move
around and still have the powerful features of Panasonic PTs. Some examples of the advantages of
wireless PTs over wireless SLTs are:
a) Caller ID
b) Seizure of outside (CO) lines by a one-touch operation
c) Carrier-based voice mail service
14
Installation Manual
1.1 System Highlights
Refer to the Operating Instructions of the wireless PT for additional information.
Advanced Hybrid System
This PBX supports the connection of PTs, wireless PTs, Direct Station Selection (DSS) Consoles,
and single line devices such as SLTs, fax machines, wireless SLTs, and data terminals.
Installation Manual
15
1.2 Basic System Construction
1.2
Basic System Construction
1.2.1
Main Unit
The KX-TA824 has a basic capacity of 3 outside (CO) lines and 8 extensions. It is capable of
supporting Panasonic proprietary telephones (PTs), and single line devices such as single line
telephones (SLTs), fax machines and data terminals.
One Caller ID card is installed by default to support the Caller ID feature for 3 outside (CO) lines.
To expand its capabilities, the PBX can be equipped with optional components or user-supplied
peripherals, such as door openers, external speakers, and an external audio source such as a radio
or CD player.
16
Installation Manual
1.2 Basic System Construction
1.2.2
System Connection Diagram
Outside (CO) Line
Remote PC
Doorphone
Door Opener/Doorbell/
Door Chime
External Audio Source
(Radio, CD player, etc.)
PC
Printer
Paging System
(Loudspeaker, Amplifier
and Speaker, etc.)
PC
SLT
PT
DSS Console
Wireless SLT
Wireless PT
FAX/Telephone
Answering Machine
Voice Processing
System
•
•
Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this extension is
automatically designated as the manager extension.
A PT and a single line telephone (SLT) can be connected in parallel to a Hybrid Port. (→ 2.5.2
Connecting Extensions in Parallel)
Installation Manual
17
1.3 Specifications
1.3
Specifications
1.3.1
General Description
Control Bus
Original bus (16-bit, 24 MHz)
Switching
Space Division CMOS Crosspoint Switch
Power Input
100 V AC to 240 V AC, 1.5 A to 0.75 A, 50 Hz/60 Hz
Maximum Power Failure Tolerance
300 ms
Memory Backup Duration
7 years
Dialing
Outside (CO) Line
Pulse (10 pps, 20 pps) or Tone (DTMF)
Extension
Pulse (10 pps, 20 pps) or Tone (DTMF)
Intercom Path
4
Mode Conversion
Pulse-DTMF
Ring Frequency
20 Hz/25 Hz (selectable)
Operating
Environment
Temperature
0 °C to 40 °C (32 °F to 104 °F)
Humidity
10 % to 90 % (non-condensing)
Conference Call Outside (CO) Line
2
Music on Hold (MOH)
1 port
Selectable MOH: Internal/External/Tone
Paging
Serial Interface Port
Internal
1
External
1 port
RS-232C
1
USB 1.1
1
Extension Connection Cable
SLT
1-pair wire (T, R)
PT
2-pair wire (T, R, H, L)
DSS Console
1-pair wire (H, L)
Dimensions
368 mm (W) × 284 mm (H) × 102 mm (D)
(14-1/2 in × 11-3/16 in × 4 in)
Weight (when fully expanded)
Approx. 3.5 kg (7.7 lb)
18
Installation Manual
1.3 Specifications
1.3.2
Characteristics
Terminal Equipment Loop Limit
PT
40 Ω
SLT
600 Ω including set
Doorphone
20 Ω
Minimum Leakage Resistance
15 000 Ω minimum
Maximum Number of Extension
Instruments per Line
1 PT or SLT in standard connection
1 PT and 1 SLT in parallel connection
Ring Voltage
75 Vrms at 20 Hz/25 Hz depending on the ringing load
Outside (CO) Line Loop Limit
1600 Ω maximum
Hookswitch Flash/Recall Timing
Range
24 ms–2032 ms
Door Opener Current Limit
30 V DC/30 V AC, 3 A maximum
Paging Terminal Impedance
600 Ω
MOH Terminal Impedance
10 000 Ω
Installation Manual
19
1.3 Specifications
1.3.3
System Capacity
System Capacity
KX-TA824
Basic System
Fully Expanded System
Outside (CO) lines
3
Extensions
8
Outside (CO) lines
8
Extensions
24
Maximum Cards and Terminal Equipment
Item
KX-TA824
PT
24
SLT
24
3-Port Analog CO Line and 8-Port Hybrid Extension Card
1
2-Port Analog CO Line and 8-Port Hybrid Extension Card
1
8-Port Hybrid Extension Card
1
Message Expansion Card for DISA OGMs
1
4-Port Doorphone Card
1
3-Port Caller ID Card
3
2-Channel Voice Message Card
1
Doorphone
4
Door Opener
4
Pager
1
Music on Hold (MOH)
1
DSS Console
2
System Data
Item
Operator
System Speed Dialing
One-touch Dialing
Personal Speed Dialing
20
Max. Quantity
1
100
24 per extension (PT)
10 per extension
Call Park Area
10
Absent Message
6
Toll Restriction (TRS) COS
5
Installation Manual
1.3 Specifications
Item
Max. Quantity
Extension Group
8
Message Waiting
8 per extension
Message for Built-in Voice Message
125 messages (total 60 minutes)
Installation Manual
21
1.3 Specifications
22
Installation Manual
Section
2
Installation
This section provides detailed instructions for installing the
PBX, optional service cards, and peripheral equipment.
Installation Manual
23
2.1 Before Installing
2.1
Before Installing
2.1.1
Before Installing
Please read the following notes concerning installation and connection before installing the PBX and
terminal equipment.
Be sure to comply with all applicable laws, regulations, and guidelines.
Safety Installation Instructions
When installing telephone wiring, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
Installation Precautions
This PBX is designed for wall mounting only, and should be installed in a location where it is
accessible for inspections and maintenance.
To prevent malfunction, noise, or discoloration, avoid installing the PBX in the following locations:
1. In direct sunlight and hot, cold, or humid places.
Temperature range: 0 °C to 40 °C (32 °F to 104 °F)
2.
3.
4.
5.
6.
Areas where sulfuric gases may be present, such as near thermal springs.
Areas where shocks or vibrations are frequent or strong.
High-dust areas, or places the PBX may come into contact with water or oil.
Near devices that generate high frequencies, such as sewing machines or electric welders.
On or near computers, telexes, or other office equipment, as well as microwave ovens or air
conditioners. (It is preferable not to install the PBX in the same room as the above equipment.)
7. Within 1.8 m (6 ft) of radios and televisions. (Both the PBX and Panasonic proprietary telephones
[PTs] should be at least 1.8 m (6 ft) away from such devices.)
8. Locations where other objects will obstruct the area around the PBX. Be especially careful to
leave at least 20 cm (8 in) of space above and 10 cm (4 in) to the sides of the PBX for ventilation.
Wiring Precautions
Be sure to follow these instructions when wiring the unit:
1. Do not run unshielded telephone cables near AC power cables, computer cables, AC power
sources, etc. When running cables near other noise-generating devices or cables, use shielded
telephone cables or shield the telephone cables with metal tubing.
2. If cables are run on the floor, use protectors to prevent the cables from being stepped on. Avoid
running cables under carpets.
3. Avoid using the same AC outlet for computers, telexes, and other office equipment, as noise
generated by such equipment may hamper system performance or interrupt the system.
24
Installation Manual
2.1 Before Installing
4. Use 2-pair telephone cables when connecting Panasonic PTs.
Use 1-pair telephone cables when connecting single line telephones (SLTs), data terminals,
answering machines, computers, voice processing systems, etc.
5. Unplug the PBX from its power source when wiring, and plug the PBX back in only after all wiring
is completed.
6. Mis-wiring may cause the PBX to operate improperly. Refer to Section 2, "Installation" when
wiring the PBX.
7. If an extension does not operate properly, disconnect the telephone from the extension line and
connect it again, or turn off the PBX using the power switch then turn it on again.
8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded
outlet, please have one installed. Do not bypass this safety feature by tampering with the plug.
9. Use twisted pair cable for outside (CO) line connection.
10. Outside (CO) lines should be installed with surge protectors. For details, refer to "2.4.1
Connecting Outside (CO) Lines", "2.2.7 Installing Surge Protector".
11. To assure good quality telephone connection, it is recommended new and modifications to
existing installation of customer premise wiring shall use solid twisted pair copper conductors
with minimum 24 gauge that comply with the electrical specifications for Category 3 wiring as
detailed in ANSI/EIA/TIA-570A Building Wiring Standards.
WARNING
Static-sensitive devices are used in this PBX. To protect printed circuit boards
from static electricity, do not touch the connectors indicated below. To discharge
static electricity from your body, touch ground or wear a grounding strap.
Side View
Warning: Static-sensitive connectors
Installation Manual
25
2.2 Installing the Advanced Hybrid System
2.2
Installing the Advanced Hybrid System
2.2.1
Unpacking
The following items are included upon shipment.
Main Unit
1
AC Cord
1
CD-ROM, Documentation
26
1 set
Screw (Wall Mounting)
3
Washer (Wall Mounting)
3
Pager Connector
1
Audio Source Connector
1
Strap
1
Rivet
1
Installation Manual
2.2 Installing the Advanced Hybrid System
2.2.2
Names and Locations
MOH Jack
Pager Jack
Extension Modular Jacks
Strap Hole
Outside (CO) Line Modular Jacks
RS-232C Port
Power Switch
USB Port
Side View
Protective Ground Terminal
AC Inlet
Run Indicator
Installation Manual
27
2.2 Installing the Advanced Hybrid System
2.2.3
Opening/Closing Covers
Opening Covers
1. Loosen the top cover screw.
2. Remove the top front cover.
Top Front Cover
Screw
Note
The screw cannot be removed from the cover.
3. Remove the 2 bottom-cover screws.
Screws
4. Open the bottom front cover.
Bottom Front Cover
28
Installation Manual
2.2 Installing the Advanced Hybrid System
Closing Covers
1. Replace the bottom front cover.
Bottom Front Cover
2. Attach the 2 bottom-cover screws.
Screws
3. Replace the top front cover and tighten the screw.
Top Front Cover
Screw
Note
For safety reasons, keep the front covers closed while the PBX is in operation.
Installation Manual
29
2.2 Installing the Advanced Hybrid System
2.2.4
Securing Cords
1. Insert the rivet into the hole in the strap.
2. Insert the rivet and strap into the hole on the PBX.
Rivet
3. Wrap the strap around all of the cords.
4. Close the covers. (→ 2.2.3 Opening/Closing Covers)
5. Tie together all of the connected cords and secure them to the wall so that they cannot be pulled
out of the PBX.
30
Installation Manual
2.2 Installing the Advanced Hybrid System
Note
To remove the rivet, use a screwdriver as shown below.
Installation Manual
31
2.2 Installing the Advanced Hybrid System
2.2.5
Connecting Frame Ground
IMPORTANT
Connect the frame of the PBX to ground.
1.
2.
3.
4.
Loosen the screw.
Grounding Wire
Insert a grounding wire (user-supplied)*.
Tighten the screw.
Connect the grounding wire to ground.
To Ground
Screw
* Use a grounding wire that has a conductor with a cross-sectional area of at least 0.75 mm2 or 18
AWG. Green-and-yellow insulation is required.
•
•
•
Be sure to comply with all applicable laws, regulations, and guidelines.
Proper grounding is very important to protect the PBX from external noise and to reduce the risk
of electrocution in the event of a lightning strike.
The AC cable's grounding pin may not be enough to protect the PBX from external noise and
lightning strikes. A permanent connection must be made between ground and the ground
terminal of the main unit.
In most of the continental United States, the ground provided by the "Third wire ground" at the
commercial power outlet will be satisfactory. However, in a small percentage of cases this ground may
be installed incorrectly. Therefore, the following test procedure should be performed.
Test Procedure
1. Obtain a suitable voltmeter and set it for a possible reading of up to 250 V AC.
2. Connect the meter probes between the 2 main AC voltage points on the wall outlet. The
reading obtained should be 108 V AC to 132 V AC.
3. Move one of the meter probes to the 3rd prong terminal (GND).
Either the same reading or a reading of 0 volt should be obtained.
4. If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other
terminal is not obtained, the outlet is not properly grounded.
This condition should be corrected by a qualified electrician (per article 250 of the National
Electrical Code).
5. If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other
terminal is obtained, then set the meter to the "OHMS/RX1" scale, place one probe at the
GND Terminal and the other probe at the terminal which gave a reading of 0 volt.
A reading of less than 1 ohm should be obtained. If the reading is not obtained, the outlet is
not adequately grounded. See qualified electrician.
32
Installation Manual
2.2 Installing the Advanced Hybrid System
2.2.6
Wall Mounting
The PBX is designed for wall mounting only. The wall where the PBX is to be mounted must be able
to support the weight of the PBX. When wall mounting the main unit, use either the included screws,
or screws of the same size.
Mounting on a Wooden Wall
The included screws may be used when mounting the main unit on a wooden wall.
1. Place the template (found on the last page of this manual) on the wall to mark the 3 screw
positions.
Template
Note
When you print out the template, the distance on the paper output may deviate slightly from the
indicated measurement. In this case, use the indicated measurement.
2. Fit the washers on the screws, and drive the screws into the wall.
Washer
Drive the screw
to this point.
3. Affix the PBX to the screw heads.
Notes
•
•
•
Do not block the openings of the cabinet. Leave at least 20 cm (8 in) of space above and 10
cm (4 in) to the sides of the PBX for ventilation.
Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings
on the back of the cabinet will not be blocked.
Be careful not to drop the cabinet.
Installation Manual
33
2.2 Installing the Advanced Hybrid System
Mounting on a Concrete or Mortar Wall
The included screws may be used when mounting the main unit on a concrete or mortar wall. Usersupplied anchor plugs are also necessary.
1. Place the template (found on the last page of this manual) on the wall to mark the 3 screw
positions.
Template
Note
When you print out the template, the distance on the paper output may deviate slightly from the
indicated measurement. In this case, use the indicated measurement.
2. Drill holes in the wall as marked and fit the anchor plugs (not included) into the holes.
Hammer
Anchor Plug
6.4 mm
(1/4 in)
29 mm
(1-1/8 in)
3. Fit the washers on the screws, and drive the screws into the anchor plugs.
Drive the screw
to this point.
4. Affix the PBX to the screw heads.
34
Installation Manual
2.2 Installing the Advanced Hybrid System
Notes
•
•
•
Do not block the openings of the cabinet. Leave at least 20 cm (8 in) of space above and 10
cm (4 in) to the sides of the PBX for ventilation.
Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings
on the back of the cabinet will not be blocked.
Be careful not to drop the cabinet.
Installation Manual
35
2.2 Installing the Advanced Hybrid System
2.2.7
Installing Surge Protector
Overview
A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above
ground, or if a telephone line comes into contact with a power line. A surge protector is a device that
is connected to an outside (CO) line to prevent potentially dangerous electrical surges from entering
the building via the outside (CO) lines and damaging the PBX and connected equipment.
To protect the PBX from electrical surges, we strongly recommend connecting the PBX to a surge
protector that meets the following specifications:
– Surge arrestor type: 3-electrode arrestor
– DC spark-over voltage: 230 V
– Maximum peak current: at least 10 kA
Additionally, proper grounding is very important for the protection of the PBX. (→ 2.2.5 Connecting
Frame Ground)
Many countries/areas have regulations requiring surge protection. Be sure to comply with all
applicable laws, regulations, and guidelines.
Installation
Outside
(CO) Line
Outside
(CO) Line
Outside
(CO) Line
Surge
Protector
Terminal
Board
Extn.
SLT
Ground
36
Installation Manual
Extn.
PBX
Extn.
PT
Frame Ground
Extn.: Extension Line
2.2 Installing the Advanced Hybrid System
Outside Installation
(Main Building)
Outside
(CO) Line
Surge Protector
(Another Building)
Outside (CO) Line
SLT
Terminal
Board
Extn.
SLT
Extn.
PBX
PT
Surge
Protector
Extn.
Extn.
PT
Ground
Extn.: Extension Line
If you install an extension outside of the building, the following precautions are recommended:
a. Install the extension wire underground.
b. Use a conduit to protect the wire.
Note
The surge protector for an extension is different from that for an outside (CO) line.
Installation of a Ground Rod
Outside
(CO) Line
Surge
Protector
Grounding Wire
PBX
(Underground)
Ground Rod
1. Connect the ground rod to the surge protector using a grounding wire with a cross-sectional area
of at least 16 AWG.
Installation Manual
37
2.2 Installing the Advanced Hybrid System
2. Bury the ground rod near the protector. The grounding wire should be as short as possible.
3. The grounding wire should run straight to the ground rod. Do not run the wire around other
objects.
4. Bury the ground rod at least 50 cm (20 in) underground.
Notes
•
•
38
Installation Manual
The above figures are recommendations only.
The length of the ground rod and the required depth depend on the composition of the soil.
2.3 Installing Optional Service Cards
2.3
Installing Optional Service Cards
2.3.1
Location of Optional Service Cards
Optional service cards are installed by opening the front covers of the main unit and affixing the cards
to the appropriate connectors. Each card should be installed in the appropriate location as shown
below.
See "System Components Table" for the description of each optional service card.
CAUTION
To protect the printed circuit boards (P-boards) from static electricity, do not touch parts on the
P-boards in the main unit and on the optional service cards. If you must touch the P-boards, wear
a grounding strap.
Connectors for KX-TA82483,
KX-TA82481 or KX-TA82470
Connector for
KX-TA82461
Connector for KX-TA82492
Connector for KX-TA82491
Connector for KX-TA82493
Note
Before installing optional service cards, turn off the PBX and unplug the AC cord.
Installation Manual
39
2.3 Installing Optional Service Cards
2.3.2
3-Port Analog CO Line and 8-Port Hybrid Extension Card
(KX-TA82483)
Function
Adds 3 outside (CO) lines and 8 hybrid extensions on the KX-TA824 basic system.
Installing KX-TA82483 to KX-TA824
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Using cutting pliers, cut the 6 parts marked with circles, and remove the upper front panel as
shown below.
Upper Front Panel
Lower Front Panel
3. Cut off any excess plastic in order to make the surface smooth.
40
Installation Manual
2.3 Installing Optional Service Cards
4. Attach the 2 extension connectors to the main unit, install the card as shown below, and secure
the 3 extension bolts.
Extension Bolts
KX-TA82483
Extension Connectors
5. Insert the modular plugs of the telephone line cords (2-conductor wiring) into the card's modular
CO ports. (→ 2.4.1 Connecting Outside (CO) Lines)
6. Connect the line cords to the terminal board or the modular jacks from the telephone company.
7. Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the card's
modular extension jacks. (→ 2.5.1 Connecting Extensions)
8. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
9. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
Installation Manual
41
2.3 Installing Optional Service Cards
2.3.3
2-Port Analog CO Line and 8-Port Hybrid Extension Card
(KX-TA82481)
Function
Adds 2 outside (CO) lines and 8 hybrid extensions on the basic system of KX-TA824.
Installing KX-TA82481 to KX-TA824
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Remove the upper front panel. Refer to the previous section for the cutting procedure.
(→ 2.3.2 3-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82483))
3. Attach the 2 extension connectors to the main unit, install the card as shown below, and secure
the 3 screws.
Screws
KX-TA82481
Extension Connectors
4. Insert the modular plugs of the telephone line cords (2-conductor wiring) into the card's modular
CO ports. (→ 2.4.1 Connecting Outside (CO) Lines)
5. Connect the line cords to the terminal board or the modular jacks from the telephone company.
6. Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the card's
modular extension jacks. (→ 2.5.1 Connecting Extensions)
7. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
8. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
42
Installation Manual
2.3 Installing Optional Service Cards
Installing KX-TA82481 on 3-Port Analog CO Line and 8-Port Hybrid
Extension Card (KX-TA82483) installed to KX-TA824
Note
Install the KX-TA82481 on top of the KX-TA82483.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Using cutting pliers, cut the 6 parts marked with circles, and remove the lower front panel or both
upper and lower front panels as shown below.
(Upper Front Panel)
Lower Front Panel
3. Cut off any excess plastic in order to make the surface smooth.
Installation Manual
43
2.3 Installing Optional Service Cards
4. Attach the extension connectors and extension bolts, install the cards as shown below, and
secure the 3 screws.
KX-TA82481
Screws
Extension Bolts
Extension Connectors
KX-TA82483
Extension Connectors
5. Insert the modular plugs of the telephone line cords (2-conductor wiring) into the card's modular
CO ports. (→ 2.4.1 Connecting Outside (CO) Lines)
6. Connect the line cords to the terminal board or the modular jacks from the telephone company.
7. Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the card's
modular extension jacks. (→ 2.5.1 Connecting Extensions)
8. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
9. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
44
Installation Manual
2.3 Installing Optional Service Cards
2.3.4
8-Port Hybrid Extension Card (KX-TA82470)
Function
Adds 8 hybrid extensions on the basic system of KX-TA824.
Installing KX-TA82470 to KX-TA824
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Remove the upper front panel. Refer to the previous section for the cutting procedure.
(→ 2.3.2 3-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82483))
3. Attach the 2 extension connectors to the main unit, install the card as shown below, and secure
the 3 screws.
Screws
KX-TA82470
Extension Connectors
4. Insert the modular plugs of the telephone line cords (2-conductor wiring) into the card's modular
CO ports. (→ 2.4.1 Connecting Outside (CO) Lines)
5. Connect the line cords to the terminal board or the modular jacks from the telephone company.
6. Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the card's
modular extension jacks. (→ 2.5.1 Connecting Extensions)
7. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
8. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
Installation Manual
45
2.3 Installing Optional Service Cards
Installing KX-TA82470 on 3-Port Analog CO Line and 8-Port Hybrid
Extension Card (KX-TA82483) installed to KX-TA824
Note
Install the KX-TA82470 on top of the KX-TA82483.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Remove the lower front panel or both upper and lower front panels. For the cutting procedure,
refer to "Installing KX-TA82481 on 3-Port Analog CO Line and 8-Port Hybrid Extension Card (KXTA82483) installed to KX-TA824". (→ 2.3.3 2-Port Analog CO Line and 8-Port Hybrid Extension
Card (KX-TA82481))
3. Attach the extension connectors, install the cards as shown below, and secure the 3 screws.
KX-TA82470
Screws
Extension Bolts
Extension Connectors
KX-TA82483
Extension Connectors
4. Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the card's
modular extension jacks. (→ 2.5.1 Connecting Extensions)
5. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
6. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
46
Installation Manual
2.3 Installing Optional Service Cards
2.3.5
3-Port Caller ID Card (KX-TA82493)
Function
Adds Caller ID support for 3 outside (CO) lines. 1 card is installed by default for outside (CO) lines 1–
3. The first optional card can be installed for outside (CO) lines 4–6 and the second optional card can
be installed for outside (CO) lines 7 and 8.
Only the FSK (Frequency Shift Keying) Caller ID type is supported. For information on the type of
Caller ID used in your area, contact your telephone company.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Slide the card between the guiderails until it clicks, and attach the connector to it.
KX-TA82493
for Outside (CO)
Lines 1–3
For Outside (CO)
Lines 7 and 8
For Outside (CO)
Lines 4–6
Note
Use extra care to make sure you do not damage the part of the case marked with a circle.
3. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
Note
To uninstall the card, follow the instructions illustrated below.
2
1
Guiderail
1. Push the catch on the side of one guiderail in the direction of the arrow to release it.
2. Lift the edge of the card while holding the catch open. (Do not touch the circuit board of the card
during the operation.)
Installation Manual
47
2.3 Installing Optional Service Cards
Feature Manual References
1.1.30 Caller ID
1.1.78 Local Carrier-based Voice Mail Service
48
Installation Manual
2.3 Installing Optional Service Cards
2.3.6
4-Port Doorphone Card (KX-TA82461)
Function
Supports the connection of 4 doorphones and 4 door openers.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Attach the 4-Port Doorphone Card to the main unit, connect the cord to the Doorphone Card
Connector and secure the screw.
Screw
KX-TA82461
Doorphone Connectors
Door Opener Terminal
Doorphone Card
Connector
Note
Use extra care to make sure you do not damage the part of the case marked with a circle.
3. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
Feature Manual References
1.1.46 Door Open
1.1.48 Doorphone Call
Installation Manual
49
2.3 Installing Optional Service Cards
2.3.7
Message Expansion Card for DISA OGMs (KX-TA82491)
Function
When an optional message expansion card for DISA OGMs is added, up to 2 messages can be
played simultaneously for callers and the total recording time of the PBX is increased from 3 to 6
minutes.
In addition, up to 10 000 incoming/outgoing outside (CO) line calls for the PBX can be logged by the
Station Message Detail Recording (SMDR) feature.
CAUTION
When uninstalling the Message Expansion Card for DISA OGMs, SMDR data stored on the card
cannot be guaranteed.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Slide the card between the guiderails until it clicks, and attach the connector to it.
KX-TA82491
Note
Use extra care to make sure you do not damage the part of the case marked with a circle.
3. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
Note
To uninstall the card, follow the instructions illustrated below.
2
1
Guiderail
1. Push the catch on the side of one guiderail in the direction of the arrow to release it.
50
Installation Manual
2.3 Installing Optional Service Cards
2. Lift the edge of the card while holding the catch open. (Do not touch the circuit board of the card
during the operation.)
Programming Manual References
[599] Clear All OGMs of DISA
8.5 DISA OGM Clear
Feature Manual References
1.1.41 Direct Inward System Access (DISA)
1.1.88 Outgoing Message (OGM) for DISA
1.1.112 Station Message Detail Recording (SMDR)
Installation Manual
51
2.3 Installing Optional Service Cards
2.3.8
2-Channel Voice Message Card (KX-TA82492)
Function
Provides 60 minutes of recording time (2 channels) for messages using the Built-in Voice Message
Feature.
1. Loosen the screws and open the top and bottom front covers. (→ 2.2.3 Opening/Closing Covers)
2. Slide the card between the guiderails until it clicks, and attach the connector to it.
KX-TA82492
Note
Use extra care to make sure you do not damage the part of the case marked with a circle.
3. Close the covers and secure the screws. (→ 2.2.3 Opening/Closing Covers)
4. Initialize the 2-Channel Voice Message Card through system programming. (→ 2.10.1 Starting
the Advanced Hybrid System)
Note
To uninstall the card, follow the instructions illustrated below.
2
1
Guiderail
1. Push the catch on the side of one guiderail in the direction of the arrow to release it.
2. Lift the edge of the card while holding the catch open. (Do not touch the circuit board of the card
during the operation.)
52
Installation Manual
2.3 Installing Optional Service Cards
Programming Manual References
[808] BV Card Initialization
8.6 BV Card Initialization
Feature Manual References
1.1.8 Built-in Voice Message (BV)
Installation Manual
53
2.4 Connecting Outside (CO) Lines
2.4
Connecting Outside (CO) Lines
2.4.1
Connecting Outside (CO) Lines
Connection
1. Insert the modular plugs of the telephone line cords (2-conductor wiring) into the outside (CO)
line jacks.
2. Connect the line cords to the terminal board or the modular jacks from the telephone company.
TEL Jack for Outside (CO) Line
T: Tip
R: Ring
T R
54
Installation Manual
To Terminal Board or Modular Jacks
from the Telephone Company
2.5 Connecting Extensions
2.5
Connecting Extensions
2.5.1
Connecting Extensions
Extension jacks can be used for proprietary telephones (PTs), Direct Station Selection (DSS)
Consoles, single line telephones (SLTs), and Voice Processing Systems.
Note
Connect a display-equipped PT to extension jack 01, as this extension is automatically
designated as the manager extension.
Connection
Insert the modular plugs of the telephone line cords (2- or 4-conductor wiring) into the modular jacks
on the PBX.
TEL Jack for Extension
H: High
T: Tip
R: Ring
L: Low
H TR L
To Extensions
Maximum Cabling Distance of Extension Wiring (Twisted Cable)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Max. Distance
140 m (459 ft)
229 m (751 ft)
360 m (1181 ft)
229 m (751 ft)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Max. Distance
698 m (2289 ft)
1128 m (3700 ft)
1798 m (5897 ft)
1128 m (3700 ft)
PT and DSS
Console
SLT
Installation Manual
55
2.5 Connecting Extensions
2- or 4-conductor wiring is required for each extension as listed below. There are 4 pins that can be
used for connection: "T" (Tip), "R" (Ring), "H" (High) and "L" (Low).
Telephone
Wiring
SLT
1-pair wire (T, R)
PT (such as KX-T7736)
2-pair wire (T, R, H, L)
DSS Console
1-pair wire (H, L)
Note
If a telephone or answering machine with an A-A1 relay is connected to the PBX, set the A-A1
relay switch on the telephone or answering machine to the "OFF" position.
56
Installation Manual
2.5 Connecting Extensions
2.5.2
Connecting Extensions in Parallel
Any single line telephone (SLT) can be connected in parallel with a proprietary telephone (PT) to a
Hybrid Port as follows:
To a Hybrid Port
Modular
T-Adaptor
2-Conductor Wiring Cord
Connect pins "T" and "R".
4-Conductor Wiring Cord
Connect pins "T", "R", "H",
and "L".
PT
SLT
Note
An answering machine, fax machine or modem can be connected in parallel with a PT in the
same way as an SLT can.
Feature Manual References
1.1.97 Paralleled Telephone
Installation Manual
57
2.6 Connecting Doorphones and Door Openers
2.6
Connecting Doorphones and Door Openers
2.6.1
Connecting Doorphones and Door Openers
Up to 4 doorphones (KX-T30865) and 4 door openers (user-supplied) can be installed.
Maximum Cabling Distance
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Max. Distance
70 m (230 ft)
110 m (360 ft)
150 m (492 ft)
110 m (360 ft)
Cable
22 AWG:
Max. Distance
150 m (492 ft)
Doorphone
Door Opener
Door opener current limit: 30 V DC/30 V AC, 3 A maximum
Installing the Doorphone (KX-T30865)
1. Loosen and remove the screw at the bottom of the case to separate the doorphone into 2 halves.
ason
ic
Pan
Screw
2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2
screws.
Screw
To the Terminal Box
58
Installation Manual
2.6 Connecting Doorphones and Door Openers
Note
2 kinds of screws are included with the KX-T30865. Please choose the appropriate screws for
your wall type.
: when a doorphone plate has been fixed to the wall
: when you wish to install the doorphone directly to the wall
3. Connect the wires to the screws located in the front cover.
To the Terminal Box
4. Re-attach the 2 halves and re-insert and tighten the screw.
Installation Manual
59
2.6 Connecting Doorphones and Door Openers
Connecting Doorphones (KX-T30865)
1. Connect the Doorphone Card to the terminal boxes using 4-conductor wiring and modular
connectors.
2. Connect the wires of doorphones 1 and 3 to the red and green screws on the appropriate
terminal box.
3. Connect the wires of doorphones 2 and 4 to the yellow and black screws on the appropriate
terminal box.
View of Doorphone Connector Jack
Doorphone 2
Doorphone 4
Doorphone 1
Doorphone 3
4-conductor wiring
is required.
Terminal Box
Yellow
Red
Black
Green
Panasonic
Panasonic
Doorphone 1
Doorphone 2
4-conductor wiring
is required.
Terminal Box
Yellow
Red
Panasonic
Doorphone 3
60
Installation Manual
Black
Green
Panasonic
Doorphone 4
2.6 Connecting Doorphones and Door Openers
Connecting Door Openers
1. Use a flathead screwdriver to press and hold open the button below the terminal, and insert the
wire coming from the door opener into the terminal.
Door Opener 1
Door Opener 2
Door Opener 4
Door Opener 3
To the Door Openers
2. Wrap the strap around all of the cords. (→ 2.2.4 Securing Cords)
Note
•
We recommend using a UL1015, 26 AWG to 22 AWG wire or an equivalent for wiring.
Feature Manual References
1.1.46 Door Open
1.1.48 Doorphone Call
Installation Manual
61
2.7 Connecting Doorbell or Door Chime
2.7
Connecting Doorbell or Door Chime
2.7.1
Connecting Doorbell or Door Chime
Use a flathead screwdriver to press and hold open the button below the terminal, and insert the wire
coming from the doorbell or door chime into the terminal. You can use a standard doorbell or door
chime. For more details, please consult your dealer.
Refer to "2.6 Connecting Doorphones and Door Openers" for connecting doorphones (KX-T30865)
and door openers.
Relay 1 Relay 2 Relay 3 Relay 4
Door
Opener 1
Doorbell/
Door Chime
Door
Opener 2
Door
Opener 3
Feature Manual References
1.1.47 Doorbell/Door Chime
1.1.48 Doorphone Call
62
Installation Manual
2.8 Connecting Peripherals
2.8
Connecting Peripherals
2.8.1
Connecting Peripherals
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Max. Distance
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
External Audio Source
(Radio, CD player, etc.)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Max. Distance
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
Paging System
(Loudspeaker,
Amplifier and
Speaker, etc.)
Max. Distance
2 m (6 ft)
PC
Max. Distance
5 m (16 ft)
Printer
PC
Note
Be sure to comply with the above maximum distance between the PBX and each peripheral.
BGM/MOH
1 audio source (user-supplied), such as a radio or CD player, can be connected to the PBX and used
as the source of Background Music (BGM) and Music on Hold (MOH).
Connect a cable from the audio output (earphone jack, headphone jack, etc.) of the audio source to
Installation Manual
63
2.8 Connecting Peripherals
the MOH Jack of the PBX.
Use an EIAJ RC-6701 A plug (2-conductor, 3.5 mm [1/8 in] in diameter).
•
Input impedance: 8 Ω
CAUTION
•
•
Notes
•
•
•
•
Do not force audio cables into the jacks. Doing so may damage the connections and cause
the audio to cut in and out.
The MOH port is an SELV port and should only be connected to an approved SELV device.
Use the supplied audio source connector in the event that the user-supplied audio cable
connector is too long and does not fit when the top front cover of the PBX is closed. Remove
the connector from the user-supplied audio cable, expose the bare cable, and attach the
supplied audio source connector.
When the PBX and external audio source are not connected to the same ground, a humming
noise may be heard in the BGM and MOH.
The audio source used for BGM and MOH is determined by system programming.
To adjust the sound level of the MOH, use the volume control on the external audio source.
Feature Manual References
1.1.7 Background Music (BGM)
1.1.85 Music on Hold
Pager
Only 1 paging device (user-supplied) can be connected to the PBX.
Use an EIAJ RC-6701 A plug (2-conductor, 3.5 mm [1/8 in] in diameter).
•
Output impedance: 600 Ω
CAUTION
The External Paging Jack is an SELV port and should only be connected to an approved SELV
device.
Notes
•
•
Use the supplied pager connector in the event that the user-supplied pager cable connector
is too long and does not fit when the top front cover of the PBX is closed. Remove the
connector from the user-supplied pager cable, expose the bare cable, and attach the
supplied pager connector.
To adjust the sound level of the pager, use the volume control on the loudspeaker or
amplifier.
Feature Manual References
1.1.92 Paging—SUMMARY
64
Installation Manual
2.8 Connecting Peripherals
PC/Printer (via RS-232C)
A PC can be connected via the RS-232C interface and used to log and display call records, and
program the PBX. A printer can also be connected, to print call records.
Connect the PC or printer via an RS-232C cable (user-supplied).
When using special accessories such as cable, the user should use those specified in this installation
manual to comply with the limits for a Class B digital device pursuant to the FCC Rules.
Note
Use an RS-232C cross cable when connecting the PBX with a PC.
Pin Assignments
Circuit Type
No.
1
5
6
9
Signal Name
Function
EIA
CCITT
2
RD (RXD)
Receive Data
BB
104
3
4
SD (TXD)
ER (DTR)
Transmit Data
Data Terminal Ready
BA
CD
103
108.2
5
6
SG
DR (DSR)
Signal Ground
Data Set Ready
AB
CC
102
107
7
8
RS (RTS)
CS (CTS)
Request To Send
Clear To Send
CA
CB
105
106
Connection Charts
For connecting a PC/printer with a 9-pin RS-232C connector
PBX
PC/Printer
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
2
2
RD (RXD)
BB
BA
SD (TXD)
3
3
SD (TXD)
BA
CD
ER (DTR)
4
4
ER (DTR)
CD
AB
SG
5
5
SG
AB
CC
DR (DSR)
6
6
DR (DSR)
CC
CA
RS (RTS)
7
7
RS (RTS)
CA
CB
CS (CTS)
8
8
CS (CTS)
CB
Installation Manual
65
2.8 Connecting Peripherals
For connecting a PC/printer with a 25-pin RS-232C connector
PBX
PC/Printer
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
2
1
FG
AA
BA
SD (TXD)
3
3
RD (RXD)
BB
CD
ER (DTR)
4
2
SD (TXD)
BA
AB
SG
5
20
ER (DTR)
CD
CC
DR (DSR)
6
7
SG
AB
CA
RS (RTS)
7
5
CS (CTS)
CB
CB
CS (CTS)
8
6
DR (DSR)
CC
8
CD (DCD)
CF
RS-232C Signals
•
Receive Data (RXD):…(input)
Carries signals from the printer or the PC to the PBX.
•
Transmit Data (TXD):…(output)
Carries signals from the PBX to the printer or the PC. Stays in "Mark" status unless data or
BREAK signals are being transmitted.
•
Data Terminal Ready (DTR):…(output)
This signal line is turned ON by the PBX to indicate that it is ON LINE. Circuit ER (DTR) ON
does not indicate that communication has been established with the printer or the PC. It is
switched OFF when the PBX is OFF LINE.
•
Signal Ground (SG)
Connects to the DC ground of the PBX for all interface signals.
•
Data Set Ready (DSR):…(input)
An ON condition of circuit DR (DSR) indicates that the printer or the PC is ready. Circuit DR
(DSR) ON does not indicate that communication has been established with the printer or the
PC.
•
Request To Send (RTS):…(output)
This is held ON whenever DR (DSR) is ON.
•
Clear To Send (CTS):…(input)
An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive
data from the PBX. The PBX does not attempt to transfer data or receive data when circuit
CS (CTS) is OFF.
•
Frame Ground (FG)
Connects to the unit frame and the ground conductor of the AC cord.
•
Data Carrier Detect (DCD):…(input)
An ON condition of circuit CD (DCD) indicates the data terminal (DTE) that the carrier signal
is being received by.
Feature Manual References
1.1.112 Station Message Detail Recording (SMDR)
66
Installation Manual
2.8 Connecting Peripherals
PC (via USB 1.1 interface)
A PC running the KX-TA Maintenance Console software can be connected via the USB interface and
used to program the system and upload/download data to the PBX.
Pin Assignments
No.
2
1
3
4
Signal Name
1
VBUS
2
USB D-
3
USB D+
4
GND
Programming Manual References
8.1 Firmware Upgrade
Feature Manual References
1.1.58 Firmware Upgrade
Installation Manual
67
2.9 Power Failure Connections
2.9
Power Failure Connections
2.9.1
Power Failure Connections
When the power supply to the PBX fails, power failure transfer will switch from the current connection
to the Power Failure Connections.
Power Failure Connections connect a specific extension and an outside (CO) line in the event of
power failure as follows:
Outside (CO) line 1—extension (T, R) jack 01
Outside (CO) line 4—extension (T, R) jack 09
Outside (CO) line 7—extension (T, R) jack 17
Notes
•
•
•
In the event of a power failure, system memory is protected by a factory-provided lithium
battery. No system data will be lost, except for the Camp-on, Saved Number Redial, Last
Number Redial and Call Park data.
The current connection automatically switches to the Power Failure Connection when the
power supply stops.
Proprietary telephones (PTs) cannot be used during a power failure. Therefore, we
recommend connecting single line telephones (SLTs) in parallel with PTs to extension jacks
01, 09, and 17.
Note that if the paralleled SLT is on an outside (CO) line call when the power is restored, that
call will be disconnected.
Feature Manual References
1.1.102 Power Failure Transfer
CAUTION
DANGER OF EXPLOSION EXISTS IF THE BATTERY IS INCORRECTLY REPLACED.
REPLACE THE BATTERY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY
THE BATTERY MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE
MANUFACTURER'S INSTRUCTIONS.
68
Installation Manual
2.10 Starting the Advanced Hybrid System
2.10 Starting the Advanced Hybrid System
2.10.1 Starting the Advanced Hybrid System
This section explains the required procedure for starting the PBX for the first time, or when using the
optional 2-Channel Voice Message Card (KX-TA82492) for the first time.
1. Make sure that all outside (CO) lines you use are connected to the PBX.
2. Set the Power Switch to the "OFF" position.
3. If installing the 2-Channel Voice Message Card, insert it into the PBX. (→ 2.3.8 2-Channel Voice
Message Card (KX-TA82492))
4. Connect the AC cord to the PBX, then plug the AC cord into an AC outlet.
5. Set the Power Switch to the "ON" position.
Note
For safety reasons, do not stretch, bend, or pinch the AC cord.
Power Switch
AC Cord
To AC Outlet
6. Enter system programming mode.
a.
b.
c.
d.
Connect a proprietary telephone (PT) to extension jack 01 of the PBX.
Press the PROGRAM button.
Press #.
Enter your System Password (Default: 1234).
7. Perform the following procedure,
[when starting the PBX for the first time]
To initialize the PBX with the default values:
a.
b.
c.
d.
Enter 999.
Press the NEXT (SP-PHONE) button and "All Para" is displayed.
Press the STORE (AUTO DIAL/STORE) button.
Press the END (HOLD) button.
Installation Manual
69
2.10 Starting the Advanced Hybrid System
Notes
•
•
The type of outside (CO) line is automatically detected.
If the PBX does not function properly, refer to "4.1.5 System Reset with System Data
Clear".
To clear outgoing messages (OGMs) for DISA:
e.
f.
g.
h.
Enter 599.
Press the NEXT (SP-PHONE) button.
Press the STORE (AUTO DIAL/STORE) button.
Press the END (HOLD) button.
[when using the 2-Channel Voice Message Card for the first time]
To initialize the 2-Channel Voice Message Card:
a.
b.
c.
d.
Enter 808.
Press the NEXT (SP-PHONE) button.
Press the STORE (AUTO DIAL/STORE) button.
Press the END (HOLD) button.
CAUTION
The 2-Channel Voice Message Card must be inserted before start up.
8. Press the PROGRAM button to exit system programming mode.
9. Program the PBX using either one of the following methods:
a. PC programming. Refer to "Section 3, Guide for KX-TA Maintenance Console".
b. PT programming. Refer to "2 PT Programming" of the Programming Manual.
CAUTION
•
•
Notes
•
•
•
The PBX is powered as long as the AC cord is plugged into an AC outlet, even if the Power
Switch is set to the "OFF" position.
The power supply cord is used as the main disconnect device. Ensure that the AC outlet is
located/installed near the equipment and is easily accessible.
If the outside (CO) lines you use are not connected to the PBX, outside (CO) line type can
not be automatically detected.
Use only the AC cord included with the PBX.
If the PBX will not be used for an extended period of time, set the Power Switch to the "OFF"
position and disconnect the AC cord from the AC outlet to conserve power.
Programming Manual References
[599] Clear All OGMs of DISA
[808] BV Card Initialization
[999] System Data Clear
8.4 System Data Clear
8.5 DISA OGM Clear
8.6 BV Card Initialization
70
Installation Manual
2.10 Starting the Advanced Hybrid System
Feature Manual References
1.1.103 PT Programming
Installation Manual
71
2.10 Starting the Advanced Hybrid System
72
Installation Manual
Section
3
Guide for KX-TA Maintenance Console
This section explains how to install and use KX-TA
Maintenance Console, a PC-based programming utility.
Installation Manual
73
3.1 Installing KX-TA Maintenance Console
3.1
Installing KX-TA Maintenance Console
3.1.1
Installing KX-TA Maintenance Console on a PC
To program and administer the PBX by PC (Personal Computer), you need to install KX-TA
Maintenance Console onto the PC.
System Requirements
Required Operating System
•
Microsoft ® Windows ® 98 SE, Windows Me, Windows 2000, or Windows XP
Minimum Hardware Requirements
•
•
•
CPU: 300 MHz Intel ® Celeron ® microprocessor
HDD: 100 MB of available hard disk space
RAM: 128 MB of available RAM
Setting the Password and Password Security
To maintain system security, a password is required to perform system programming. When KX-TA
Maintenance Console is started for the first time, the Quick Setup utility will ask you to set the system
password. To avoid unauthorized access and possible fraudulent dialing, do not disclose the
password.
Warning to the Installer regarding the system password
1. Please inform the customer of the importance of the password and the possible dangers if
it becomes known to others.
2. To avoid unauthorized access and possible fraudulent dialing, maintain the secrecy of the
password.
3. We strongly recommend that you change the default password value to something else for
reasons of system security. It is best to use a password of 7 digits.
4. Please change the password periodically.
5. If a system password is forgotten, it can be found by loading a backup of the system data
into a PC, and checking the password using the KX-TA Maintenance Console software. If
you do not have a backup of the system data, you must reset the PBX to its factory defaults
and reprogram it. Therefore, we strongly recommend maintaining a backup of the system
data.
For more information on how to back up the system data, refer to the on-line help that
appears by selecting the Help menu during PC programming. However, as system
passwords can be extracted from backup copies of the system data file, do not allow
unauthorized access to these files.
Note
This PBX has only one system password. It can be changed by either PT programming or PC
programming. For this reason, the password can consist of numerals only.
74
Installation Manual
3.1 Installing KX-TA Maintenance Console
Installing KX-TA Maintenance Console
Notes
•
•
Before installing or uninstalling the software, be sure to close any open applications.
To install or uninstall the software on a PC running Windows 2000 Professional or Windows
XP Professional, you must be logged in as a user in the "Administrators" group.
1. Insert the included CD-ROM into the CD-ROM drive of your PC.
The main screen will appear automatically.
2. Click Maintenance Console.
3. Double-click the setup file to run the installer. (Its icon is shown here, on the left.)
4. Follow the on-screen instructions provided by the installation wizard.
Programming Manual References
3.2 PC Programming
Feature Manual References
1.1.99 PC Programming
Installation Manual
75
3.2 Connection
3.2
Connection
3.2.1
Connection
PBX features and settings can be customized using a PC and the KX-TA Maintenance Console
software.
Programming can be performed both on-site, using a PC connected directly to the PBX, and off-site,
by accessing the PBX via modem.
Serial Interface Connection
A PC can be connected to the RS-232C port of the PBX, or to the USB port for faster access.
RS-232C Port
To COM Port
PC
To USB Port
PC
USB Port
Notes
•
•
For pin assignments and maximum cabling distance, refer to "2.8 Connecting Peripherals".
When connecting the KX-TA Maintenance Console to the PBX using an RS-232C cable,
assign the following values to the Serial Interface (RS-232C) port of the PBX through system
programming, "[800] SMDR RS-232C Parameter":
•
Baud Rate: 9600 bps
•
Word Length: 8 bits
•
Parity Bit: None
•
Stop Bit: 1 bit
Installing the USB Driver
CAUTION
Installing the USB driver may prevent the USB driver for KX-TDA series or PC Console/Phone
Software from functioning correctly. In this case, update the USB drivers as necessary from the
following folders on the included CD-ROM:
76
Installation Manual
3.2 Connection
KX-TDA Series: CD-ROM Drive:\TDA_USB Driver\TDA_USB Driver
PC Console/Phone Software: CD-ROM Drive:\TDA_USB Driver\T7601_USB Driver
Note
Before installing or uninstalling the driver, be sure to close any open applications.
Windows 98SE
1. Connect the PC to the PBX with a USB cable.
The Add New Hardware Wizard will appear.
2.
3.
4.
5.
6.
7.
8.
Click Next.
Select Search for the best driver for your device. [Recommended], then click Next.
Select Specify a location, then click Browse.
Specify the folder containing the USB driver, CD-ROM Drive:\USB driver\Win98, then click OK.
Click Next.
Click Next.
Click Finish.
Note
If a dialog box appears asking you to restart your PC, restart the PC.
Windows Me
1. Connect the PC to the PBX with a USB cable.
The Add New Hardware Wizard will appear.
2.
3.
4.
5.
6.
7.
8.
Select Specify the location of the driver [Advanced], then click Next.
Select Search for the best driver for your device. [Recommended].
Select Specify a location, then click Browse.
Specify the folder containing the USB driver, CD-ROM Drive:\USB driver\WinMe, then click OK.
Click Next.
Click Next.
Click Finish.
Note
If a dialog box appears asking you to restart your PC, restart the PC.
Windows 2000
1. Connect the PC to the PBX with a USB cable.
The Found New Hardware Wizard will appear.
2.
3.
4.
5.
Click Next.
Select Search for a suitable driver for my device. [Recommended], then click Next.
Select Specify a location, then click Next.
Click Browse, and specify the folder containing the USB driver, CD-ROM Drive:\USB
driver\Win2000, then click Open.
6. Click OK.
7. Click Next.
8. Click Finish.
Installation Manual
77
3.2 Connection
Windows XP
1. Connect the PC to the PBX with a USB cable.
The Found New Hardware Wizard will appear.
2.
3.
4.
5.
6.
7.
8.
Select Install from a list or specific location [Advanced], then click Next.
Select Search for the best driver in these locations.
Select Include this location in the search:, then click Browse.
Specify the folder containing the USB driver, CD-ROM Drive:\USB driver\WinXP, then click OK.
Click Next.
Click Continue Anyway.
Click Finish.
Programming Manual References
4.1 Software Modes
6.1 Connect
Feature Manual References
1.1.99 PC Programming
78
Installation Manual
3.2 Connection
3.2.2
Starting KX-TA Maintenance Console for the first time
When you start the KX-TA Maintenance Console with the Installer Level Programmer Code and
connect to the PBX for the first time after initialization (with factory default setting), Quick Setup will
launch automatically. During Quick Setup, you will setup:
•
The date and time. The PBX uses the date and time set to the PC.
•
The System Password.
•
The operator extension number.
•
Automatic Configuration for CO Line Type (DTMF [Dual Tone Multi-Frequency]/Pulse).
•
The feature numbers for Operator Call and Automatic Line Access.
•
Extension numbers and names.
•
The Numbering Plan type.
•
Ringing assignment for each outside (CO) line (either all extensions, or a specific extension).
Note
The screenshots shown here are for reference only, and may differ from the screens displayed
on your PC.
1. Start the KX-TA Maintenance Console software
from the start menu. (Start → Programs → KX-TA
Maintenance Console)
2. Type the Installer Level Programmer Code that was
set during the KX-TA Maintenance Console
installation.
3. a.
Click the check box to connect to the PBX.
Options will appear as shown here, on the left.
b. Type the System Password. (default: 1234)
c. Select the method of connection.
d. Click OK to log in.
4. Quick Setup starts. Follow the on-screen
instructions and assign the items as prompted.
Note
Software features, design, and system requirements are subject to change.
Programming Manual References
4.1 Software Modes
6.1 Connect
8.2 Quick Setup
Installation Manual
79
3.2 Connection
3.2.3
Accessing PBX via Internal Modem
1. Start the KX-TA Maintenance Console software
from the start menu on your PC. (Start → Programs
→ KX-TA Maintenance Console)
2. Type the Installer Level Programmer Code that was
set during the KX-TA Maintenance Console
installation.
3. Click the check box to connect to the PBX. Options
will appear as shown here, on the left.
4. Type the System Password. (default: 1234)
5. Select Modem, and click Setup.
When the mode of the PBX outside (CO) line that will be accessed is 'MODEM':
1.
2.
3.
4.
For Dial Number, enter the telephone number assigned to the internal modem of the PBX.
Select Auto (Tone) or Auto (Pulse) for Dial Type.
Click OK.
Click OK. The PC will connect to the PBX.
When the mode of the PBX outside (CO) line that will be accessed is 'DISA':
1. For Dial Number, enter the telephone number assigned to the internal modem of the PBX,
several pause symbols (',') and the Remote Maintenance feature number (for example:
01234567,,,,,729).
2. Select Auto (Tone) for Dial Type.
3. Click OK.
4. Click OK. The PC will connect to the PBX.
Notes
•
•
The number of pause symbols to be inserted differs depending on the PC modem used.
Auto (Pulse) Dial Type cannot be used.
When the mode of the PBX outside (CO) line that will be accessed is 'Normal':
1.
2.
3.
4.
5.
6.
80
Installation Manual
For Dial Number, enter the pause symbol (',').
Select Manual for Dial Type.
Click Initialize.
Click OK.
Click OK.
Dial the telephone number assigned to the outside (CO) line from a telephone connected in
parallel with the PC.
3.2 Connection
7. Ask the respondent to transfer the call to the internal modem of the PBX. ('Transfer' + '729
[Remote Maintenance feature number]')
8. Click OK and wait for 2 or 3 seconds, and then go on-hook before you hear a tone from the
modem. The PC will connect to the PBX.
Notes
•
•
•
•
•
The AT command 'Use V.22bis' may be required to configure the modem to communicate
with the PBX, depending on the modem (for example: "AT + MS = V22B").
The AT commands 'Use V.42' and 'Use V.42bis' may be required to configure the modem to
communicate with the PBX, depending on the modem.
The AT command to dial without waiting for a dial tone may be required to configure the
modem to communicate with the PBX, depending on the modem.
The AT command to set the Result Code format to text beginning with 'CONNECT' when a
connection is established may be required to configure the modem to communicate with the
PBX, depending on the modem.
If the Baud Rate (bps) is set too high or too low the modem may not be able to communicate
with the PBX, depending on the modem or PC. In this case, adjust the Baud Rate (bps) and
reconnect to the PBX.
Programming Manual References
4.1 Software Modes
6.1 Connect
Installation Manual
81
3.2 Connection
82
Installation Manual
Section
4
Troubleshooting
This section provides information on troubleshooting and
restarting the PBX.
Installation Manual
83
4.1 Troubleshooting
4.1
Troubleshooting
4.1.1
Installation
PROBLEM
•
PROBABLE CAUSE
Extension telephone does •
not function.
SOLUTION
Faulty connection
between the PBX and
telephone.
•
Plug the telephone into the same
extension port using a short telephone
cord.
If the telephone functions, then the
connection between the PBX and the
telephone must be repaired.
•
Faulty telephone.
•
Plug the telephone into a known
functioning extension port. If the telephone
does not function, replace the telephone.
•
A telephone with an A-A1 •
relay is connected.
Use a 2-wire cord.
Set the A-A1 relay switch of the telephone
to the "OUT" or "OFF" position.
•
Faulty extension card.
•
Exchange the card for a known functioning
one.
•
Proprietary telephones
(PTs) connected to
extension jacks do not
operate, but single line
telephones (SLTs) do.
•
The H and L pins of
•
extension jacks may have
shorted.
Turn the Power Switch to the "OFF"
position. Fix the shorted part, then turn the
Power Switch to the "ON" position.
•
Noise heard through
external pager
(loudspeaker).
•
If using an amplifier, noise •
may be being introduced
through the cable
connecting the PBX and
the amplifier or
loudspeaker.
Use a shielded cable to connect the PBX
and the amplifier or loudspeaker. A shorter
cable will introduce less noise.
•
Audio (Music on Hold,
Background Music) is
distorted.
•
Audio level from the output •
of the audio source is too
high.
Decrease the output level of the external
audio source by using the volume control
on the audio source.
•
Speed Dialing or Onetouch Dialing does not
function.
•
Incorrect programming.
•
Store the outside (CO) line access number
(for example, 9, 81 through 88) at the
beginning of the telephone number.
•
Improper operation other
than the above.
•
Turn the Power Switch to the "OFF"
position, and then back to the "ON"
position.
84
Installation Manual
4.1 Troubleshooting
4.1.2
Connection
Telephone cord connecting the PBX and a proprietary telephone (PT):
Can you dial
an extension?
No
CAUSE
SOLUTION
The T/R pins are connected to the H/L
pins.
H
T
R
L
H
T
R
L
Use the correct cord (the
inner 2 wires are for T/R and
the outer 2 wires are for H/L).
Extension
PBX
Telephone cord connecting the PBX and a single line telephone (SLT):
CAUSE
SOLUTION
The T/R pins are connected to the H/L
pins.
H
T
R
L
T
R
PBX
Yes
Use the correct cord (the
inner 2 wires are for T/R).
Extension
Telephone cord connecting the PBX and an SLT that is polarity-sensitive:
CAUSE
SOLUTION
The T and R pins are crossed over.
H
T
R
L
Reverse the connections of
the T/R pins.
T
R
PBX
Extension
Telephone cord connecting an outside (CO) line and the PBX:
CAUSE
SOLUTION
The outside (CO) line(s) is
connected to the H/L pins.
Can you dial
out using an
outside (CO)
line?
Reconnect the outside
(CO) line(s) to the T/R pins
of the telephone jack using
2-conductor wiring.
No
T
R
Outside (CO) Line
PBX
Installation Manual
85
4.1 Troubleshooting
4.1.3
Operation
PROBLEM
PROBABLE CAUSE
SOLUTION
•
•
When using the
speakerphone on a
proprietary telephone
(PT), no sound is heard.
•
The HANDSET/
HEADSET selector is set
to the "HEADSET"
position.
•
The PT does not ring.
•
The ringer volume is set to •
off.
•
During a power failure,
PTs connected to jack
numbers 01, 09, or 17 do
not operate.
•
•
When the headset is not used, set the
HANDSET/HEADSET selector to the
"HANDSET" position.
Set to "HIGH" or "LOW".
•
Only single line telephones (SLTs) can be
used during a power failure. Disconnect
the PT and connect an SLT.
Outside (CO) line calls
•
cannot be made with a PT.
A flexible button on the PT •
has not been programmed
to select an outside (CO)
line.
Program the CO buttons. Refer to "1.1.61
Flexible Buttons" in the Feature Manual.
•
An SLT set to "tone"
dialing mode cannot make
calls.
There may be something
wrong with the DTMF
(Dual Tone MultiFrequency) receiver.
1. Select "Enable" for DTMF receiver 1 and
"Disable" for DTMF receiver 2 through
system programming, "[107] DTMF
Receiver Check".
2. Try to make a call using a tone-type SLT
connected to one of extension jacks 01–
08.
3. If you cannot make the call, the problem
may have been caused by DTMF receiver
1. If the call can be made, go to step 4.
4. Try DTMF receiver 2. Select "Disable" for
DTMF receiver 1 and "Enable" for DTMF
receiver 2 through system programming,
"[107] DTMF Receiver Check", and make
another call. If you cannot make the call,
the problem may have been caused by
DTMF receiver 2. If the call can be made,
go to step 5.
5. Check the other 4 DTMF receivers the
same way through "[107] DTMF Receiver
Check" in system programming.
86
Installation Manual
4.1 Troubleshooting
4.1.4
System Restart
If the PBX does not operate correctly, confirm that the operation/feature is being used correctly and
refer to the Troubleshooting section if necessary. If the PBX still does not operate correctly, restart the
PBX.
When the PBX is restarted:
•
Calls on Hold are terminated.
•
Calls on Exclusive Hold are terminated.
•
Calls in progress are terminated.
•
Automatic Callback Busy (Camp-on) is cleared.
•
Call Park is cleared.
•
Last Number Redial is cleared.
•
Saved Number Redial is cleared.
No other data is cleared by System Restart.
1. To restart the PBX, turn the Power Switch to the "OFF" position, then turn the Power Switch back
to the "ON" position.
Note
If the PBX still does not operate correctly, please see "4.1.5 System Reset with System Data
Clear".
Installation Manual
87
4.1 Troubleshooting
4.1.5
System Reset with System Data Clear
When the PBX does not operate correctly after restarting, you can clear the programming data stored
in the PBX. The PBX will restart with the default settings.
1. Make sure that all outside (CO) lines you use are connected to the PBX.
2. Slide the System Clear Switch to the "CLR" position.
3. Press the Reset Button, and then return the System Clear Switch to the "NOR" position before
the power indicator stops flashing. (The power indicator will flash for about 5 seconds.)
CAUTION
Before touching the System Clear Switch and Reset Button, put on a grounding strap.
Notes
•
•
After pressing the Reset Button, make sure to return the System Clear Switch to the "NOR"
position before the power indicator stops flashing, otherwise the system data will not be
cleared.
The recorded outgoing messages (OGMs) for Direct Inward System Access (DISA) and
Built-in Voice Message (BV) are not cleared by the System Data Clear.
RESET
NOR/CLR
System Clear Switch
Reset Button
Programming Manual References
[999] System Data Clear
8.3 System Reset
8.4 System Data Clear
88
Installation Manual
Section
5
Appendix
Installation Manual
89
5.1 Revision History
5.1
Revision History
5.1.1
Version 2.0
Changed Contents
90
•
2.3.7 Message Expansion Card for DISA OGMs (KX-TA82491)
•
2.3.8 2-Channel Voice Message Card (KX-TA82492)
•
2.10.1 Starting the Advanced Hybrid System
Installation Manual
Index
Installation Manual
91
Index
Numerics
2-Channel Voice Message Card (KX-TA82492)
52
2-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82481)
42
3-Port Analog CO Line and 8-Port Hybrid Extension Card (KX-TA82483)
40
47
3-Port Caller ID Card (KX-TA82493)
4-Port Doorphone Card (KX-TA82461)
49
45
8-Port Hybrid Extension Card (KX-TA82470)
Mounting on a Concrete or Mortar Wall
Mounting on a Wooden Wall
33
N
Names and Locations
27
O
Opening/Closing Covers
86
Operation
A
P
About the Installation Manual
8
8
About the Other Manuals
Accessing PBX via Internal Modem
Appendix
89
Power Failure Connections
80
Revision History
90
Safety Installation Instructions
24
30
Securing Cords
Serial Interface Connection
76
74
Setting the Password and Password Security
18
Specifications
Starting KX-TA Maintenance Console for the first time
69
Starting the Advanced Hybrid System
20
System Capacity
System Components Table
2
17
System Connection Diagram
20
System Data
System Highlights
14
13
System Outline
74
System Requirements
System Reset with System Data Clear
88
87
System Restart
C
Characteristics
19
Connecting Doorbell or Door Chime
62
Connecting Doorphones and Door Openers
55
Connecting Extensions
Connecting Extensions in Parallel
57
32
Connecting Frame Ground
54
Connecting Outside (CO) Lines
Connecting Peripherals
63
76, 85
Connection
58
E
Expandability of Outside (CO) Lines and Extensions
2
T
G
Troubleshooting
General Description
18
Guide for KX-TA Maintenance Console
83
73
U
I
Unpacking
Installation
23, 84
Installation Precautions
24
75
Installing KX-TA Maintenance Console
Installing KX-TA Maintenance Console on a PC
Installing Optional Service Cards
39
36
Installing Surge Protector
26
Installing the Advanced Hybrid System
Installing the USB Driver
76
Version 2.0
74
Wall Mounting
33
24
Wiring Precautions
39
Main Unit
16
Maximum Cabling Distance of Extension Wiring (Twisted Cable)
Maximum Cards and Terminal Equipment
20
50
Message Expansion Card for DISA OGMs (KX-TA82491)
90
W
M
Installation Manual
26
V
L
92
68
S
16
Location of Optional Service Cards
28
R
B
Basic System Construction
Before Installing
24
34
55
79
169 mm (6-5/8 in)
Install a screw here.
Install a screw here.
92.5 mm (3-5/8 in)
236 mm (9-5/16 in)
TEMPLATE FOR WALL MOUNTING
1. Copy or print this template and place it on the wall.
2. Install the screws as marked.
If you mount the main unit on a concrete or mortar wall, fit anchor plugs
(not included) into the wall beforehand.
3. Hook the unit onto the screw heads.
Install a screw here.
Note
Make sure to set the print size to correspond with the size of this page.
If the dimensions of the paper output still deviate slightly from the measurements
indicated here, use the measurements indicated here.
118 mm (4-5/8 in)
185 mm (7-5/16 in)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5,
Carolina, Puerto Rico 00985
http://www.panasonic.com/csd
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal
use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic
Communications Co., Ltd.
© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.
PSQX3400WA KK0405PY3047
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement