Diamond Audio HXM1200.6D Owner's Manual

 DIAMOND
A UU DP II oO
1225 E. 7th Street
Los Angeles, CA. 90021
©2014 Diamond Audio. All fights reserved.
(a division of CV & DA Holdings, Inc.)
www.DiamondAudio.com
HXM800.2D/HXM800.4D/HXM8001D
HXM1200.1D/1200:6D
<>
Onmers Manual
INTRODUCTION
Congratulations, you have just purchased one of the finest mobile audio products on the
market. Diamond Audio products represent the latest advances in acoustic technology in
sound reproduction for your vehicle. Diamond Audio products are designed, developed, and
engineered in the USA using the latest innovative materials and components to provide the
finest sound reproduction possible. Every Diamond Audio product has been verified and
tested to ensure the best sounding and most reliable product on the market, if installed
properly .Diamond Audio products will provide many years of the ultimate listening experience.
Please note that prolonged exposure to sound pressure levels in excess of 100dB can cause
permanent hearing loss. Using Diamond Audio products can exceed that level so please
exercise restraint in its operation in order to preserve your ability to enjoy its high fidelity sound
for many years to come.
Diamond Audio recommends our products be professionally installed by an authorized
Diamond Audio dealer to achieve the best possible system recommendation and installation.
This will ensure a true Diamond Audio listening experience and sound you would expect from
Diamond Audio products. With proper validation, using a Diamond Audio Retialer for installation,
your newly purchased amplifier, Diamond Audio will extend the product warranty from one year
to Two Years!
Go ahead, Hear the Music
WARRANTY
Diamond Audio Technologies (DAT), a division of CV & DA Holdings Incorporated, warrants this product to be free from
defects in material and workmanship for a period of one (1) year from the original date of purchase, provided it was
purchased from an authorized DAT retailer within the United States. Product warranty period starts at the date of
purchase or one year past the manufacture date whichever is first. However, upon purchase and completion of the
on-line registration and installation by an authorized DAT dealer you warranty period will be extended to two (2) years.
This warranty extension offer will only be recognized upon completion of the on-line registration of your product within
thirty (30) days of the date of purchase.
THIS WARRANTY IS NOT TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER OF THIS PRODUCT
IN ITS ORIGINAL INSTALLATION. Original purchaser must reside in the United States and be able to provide proof of
purchase and installation with the sales receipt and completion of online regoistration from the authorized DAT retailer that
sold and installed the product.
Should a manufacturing defect occur during above said warranty period, DAT will replace or repair the defective product
with a product of the same or equivalent value and performance, at DAT's discretion.
Damage or failure caused by any of the following is not covered under this warranty policy: negligence, improper use,
abuse, product modification, unauthorized repair attempts, accident, acts of God, misrepresentations by DAT retailers, and
improper/inadequate packaging during return shipping.
Warranty is void if serial numbers have been removed, altered or defaced.
HOW TO OBTAIN WARRANTY SERVICE
In the event a DAT product should require service, you should visit the authorized DAT retailer you purchased the product
from and they can expedite your claim. All claims must fall into the guidelines listed above and be accompanied by a copy of
the original sales and installation receipt from that authorized DAT retailer.
Product returned for warranty service must be freight-prepaid, properly packaged and clearly marked with the Return
Authorization (RA) number issued by DAT. Any product returned to DAT that is improperly packaged, does not have a
RA number clearly marked on the package, or never received a RA number may be refused upon delivery. DAT does not
assume responsibility for lost or misdirected product.
Repair or replacement under this warranty is the exclusive remedy of the consumer. DAT shall not be liable for any
incidental or consequential damages for breach of any expressed or implied warranty on this product. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights that may vary from state to state.
Customers outside the United States should contact their local sales office to obtain information on pricing, exchange unit
availability, instructions, service and warranty/non-warranty replacement or repair.
Diamond Audio Technologies Service/Tech Support:
1225 E.7th ST 213-261-4161
LOS ANGELES, CA 90021 Tech Support Email
Tel: 213-261-4161
Fax: 213-947-4767
Web: diamondaudio.com
[email protected]
En
SPECIFICATIONS
PRODUCT SPECIFICATIONS
MODEL:
Power Rating
RMS Power (10)
RMS Power (2 0)
RMS Power (4 Q)
Type
Topology
Power Supply
Power Supply
Power Supply Threshold
Idle Current
Distortion
THD (1KHz 240)
S/N Ratio (A weighted @1W)
S/N Ratio (A weighted @ FP)
Input Sensitivity
Low Input Level
High Input Level
Input Impedance
Low Input Level
High Input Level
Output Stage
Output Impedance
Damping Factor (50Hz @ 40)
Bandwidth (-3dB)
Crossover (-12dB/Oct)
Variable High-Pass
Variable Low-Pass
Variable Sub-Sonic
Fuse Ratings
ATC
Dimensions
Lenght x Width x Height (inches)
Lenght x Width x Height (mm)
HXM800.1D
800 W X 1 RMS
550 WX 1 RMS
350 WX 1 RMS
MonoBlock Class D
Full PWM
10.0VDC -
17.0VDC
(0.78)
0.05%
-77.20BA
-98.9dBA
0.2mV - 10.0V
YES - UP to 25 W RMS
22 КО
22 КО
0.0470
>250
10Hz-350Hz
N/A
30Hz - 300Hz
10Hz - 55Hz
N/A
8.56 x 5.27 x 1.75
217.6 x 133.9 x 44.5
HXM1200.1D
1200 W X 1 RMS
850 W X 1 RMS
550 WX 1 RMS
MonoBlock Class D
Full PWM
10.0VDC-
17.0VDC
(0.78)
0.07%
-77.4dBA
-97.4dBA
0.2mV - 10.0V
YES - UP to 25 W RMS
272 KQ
22 КО
0.0470
>250
10Hz-350Hz
N/A
30Hz - 300Hz
10Hz - 55Hz
N/A
11.72 x 5.27 x 1.75
297.6 х 133.9 х 44.5
INSTALLATION - Pre Planning Section
WARNING: Prolonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss.
Cerwin Vega Mobile amplifiers can exceed that level so please exercise restraint when listening and enjoying your new amplifier.
GENERAL PRECAUTIONS
eThis unit is designed for negative ground 12V DC operation only.
Total system impedance must not be less than 2ohms, in a bridged OR stereo configuration
Avoid installing the unit where:
- It would be subject to high temperatures, such as from direct sunlight or hot ir from the heater.
- It would be exposed to rain or moisture.
- It would be subject to dust or dirt.
eDo not cover the unit with carpet or wires.
eDo not use the unit with a weak auto battery. Optimum performance depends on a normal battery supply voltage.
efor safety reasons, keep the volume of your car audio system moderate while driving your vehicle so that you can still hear
normal traffic sounds outside your car.
eThere is NO speaker level input connector, you can cut RCA's and solder the wires and connect directly thru low level input(RCA)
MOUNTING PRECAUTIONS
Although Cerwin Vega Mobile amplifiers incorporate heat sinks and protection circuits, mounting the amplifier in a tight space
without any air movement can still damage internal circuitry over time. Choose a location that provides adequate ventilation
around the amplifier. For easy system set-up, mount the amplifier so the side panel controls will be accessible after
installation. To increase thermal run times on low impedance loads, an additional fan is recommended, remember any moving
air across the amplifier will reduce heat.
In addition, observe the following precautions:
1. Using a felt pen mark the mounting hole locations.
2. Mounting the amplifier on carpet will significantly reduce air flow, resulting in reduced thermal run times.
3. Mount the amplifier on a solid surface. Avoid mounting to sub woofer enclosures or areas prone to vibration. Do not install
the amplifier on plastic or other combustible materials.
4. Prior to mounting the amplifier, make sure not to cut or drill info the fuel tank, fuel lines, brake lines (under chassis) or
electrical wiring.
WIRING PRECAUTIONS
1. Before installation, make sure the source unit power switch is in the OFF position.
2. Disconnect the negative (-) lead of the battery before making any power connections.
3. When making connections, be sure that each one is clean and secure. Insulate all of your connections. Failure to do so
may damage your equipment.
4. A secure clean ground connection is critical to the performance of your amplifier. Connect the ground directly fo the car
chassis to minimize resistance and avoid any noise problems.
5. Add an external fuse on the amplifier's positive (+) power lead and connect it as close as possible to the vehicles (+)
battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. This
external fuse will protect the vehicle from short circuits that can cause a fire.
13
FEATURES
SPECIFICATIONS
HXM800.2D
HXM800.4D
HXM800.1D
134MM/5.3IN
| 9.74"/247.6mm - |
5.27"/133.9тт — — — — — —>
[a-1.75"/44.5mm-=
5.27"/133.9тт — — — — — =
le-1.75"/44.5mm =
MODEL:
Power Rating
RMS Power (2 (0)
RMS Power (4 0)
Bridged (mono 1 ©)
Bridged (mono 2 0)
Bridged (mono 4 Q)
Type
Topology
Power Supply
Power Supply
Power Supply Threshold
Idle Current
Distortion
THD (1KHz @40)
S/N Ratio (A weighted @1W)
S/N Ratio (A weighted @ FP)
Input Sensitivity
Low Input Level
High Input Level
Input Impedance
Low Input Level
High Input Level
Output Stage
Output Impedance
Damping Factor (50Hz @ 40Q))
Bandwidth (-3dB)
Crossover (-12dB/Oct)
Variable High-Pass
Variable Low-Pass
Variable Sub-Sonic
Fuse Ratings
ATC
Dimensions
Lenght x Width x Height (inches)
Lenght x Width x Height (mm)
PRODUCT SPECIFICATIONS
HXM800.2D
400 W Y 2
300 WX 2
N/A
N/A
800 W X 1(4 À ONLY)
Ful-Range Class D
Full PWM
10.0VDC -
17.0VDC
(0.78)
0.05%
-77.2dBA
-98.9dBA
0.2mV - 10.0V
YES - UP to 25 W RMS
272 KQ
0.0470
>250
10Hz-35KHz
40Hz - 400Hz
40Hz - 400Hz
N/A
N/A
9.74 x 5.27 x 1.75
247.6 x 133.9 х 44.5
HXM800.4D
200WX4
120WX4
N/A
N/A
400 W X 2(4 Q ONLY)
Ful-Range Class D
Full PWM
10.0VDC -
17.0VDC
(0.74)
0.07%
-77.4dBA
-97.4dBA
0.2mV - 10.0V
YES - UP to 25 W RMS
272 KQ
0.0470
>250
10Hz-35KHz
40Hz - 400Hz
40Hz - 400Hz
N/A
N/A
9.3 x 5.27 x 1.75
237x 133.9 x 44,5
HXM1100.6D
150WX 4 /250X 2
90WX4/150X2
N/A
N/A
300 W X 2/500 W X 1(Ch 5/6 bridged)
Ful-Range Class D
Full PWM
10.0VDC -
17.0VDC
(0.7A)
0.03%
-76.7dBA
-96.7dBA
0.2mV - 10.0V
YES - UP to 25 W RMS
22 КО
0.051 0
>/0
10Hz-35Hz
40Hz -400Hz
30Hz - 300Hz
N/A
N/A
12.5x 5.27 x 1.75
317.6 x 133.9 x 44.5
[17
SYSTEM CONFIGURATIONS
FUNCTIONS
HXM - 5 CHANNEL/2 AMPLIFIER BOAT SYSTEM
HXM800.4D STEREO 2 OHM (8 SPEAKERS - 2 OHM LOAD)
HXM800.1D MONO 1 OHM (TO SUBWOOFER{S})
DABTR10
(OR ANY DA
SMARTPHONE BLUETOOTH RECEIVER)
(BLUETOOTH) DW
) СМ
4 - 8 INCH HXM8
EXTREME HIGH OUTPUT
3-WAY SPEAKER
I (2 OHMS ALL CHANNELS)
hannel HXM800.4D
panel connection)
= re FRE A A 2
oie. 0,005
(EE 0 00 yA
[Г НН ВЫ = où —
SPECIAL BTR CABLE
(INCLUDED WITH BTR)
BATTERY
Remote Bass
Control
1 Channel HXM800.1D
(front panel connection)
4 - 8 INCH HXM8
EXTREME HIGH OUTPUT
3-WAY SPEAKER
(2 OHMS ALL CHANNELS)
||
©. [И
HXM800.1D
DIAMOND
2 - 10 INCH HIGH OUTPUT
SUBWOOFER
(1 OHM MONO)
- |
| 2ND AMP TURN-ON SETUP
SPECIAL NOTE:
2nd amplifer in a full BTR
setup must use either “VOX”
or “DC” for the remote
turn-on configuration
(see page 11)
© Status LED’s - These lights indicate when the amplifier is powered up normally and when there is a protection fault. The Protect
LED is laminated when there is a problem with your amplifier. Please contact your authorize CVM dealer or call CVM's technical support.
(2) Input Gain Adjustment (SENS)- This control matches the preamp stage of the Cerwin-Vega Mobile amplifier to your source unit
This is NOT a volume control. The range is between aprox 0.2mV and 10V. Using the adaptor CHHILVL you can run speaker level in.
©) Input Configuration - This switch parallels the input circuit if you are using a single stereo pair of outputs from your headunit
or from an auxiliary device (like a Smartphone, etc). The 5 channel model (V1000.5D) is set up to accept 2/4 /and 5 channels of input.
Turn-On Mode Switch - This switch allow you to configure the “Turn-On Mode” switch for desired turn-on trigger. There are 3 modes
available are REM, DC and VOX. 1 - (REM) is the standard 12V trigger wire, 2 - (DC) or DC offset, when connected high level in, will sense
differences in ground in your wiring through the speaker leads and turn on amplifier, 3 - VOX (signal sensing) will sense any kind of signal
input info the amplifier RCA turning on the amplifier. Select VOX when using any Cerwin-Vega Mobile Bluetooth Controller.
PreAmp Output Select - This switch allow you to select from which input you will use to be the ouput signal to the next amplifier
in the signal chain. For example for a 4 channel to a mono block to make a front/rear/sub system minimizing long RCA cables.
(6) Crossover Selection Switch - This switch allow you to select the crossover function. HPF (High Pass Filter) LPF (Low Pass Filter) or FLAT
(no filter), HPF is for filtering out bass for midrange/mid bass drivers. LPF is for filktering out hogh frequencies for subwoofers The range of
adjustment is limited between 40-400Hz @12dB per octave (SRPM750/1000/1100.5D is 30-300 Hz @12dB per octave).
7) Crossover Frequency Adjustment - Use this adjustment to select the crossover point LPF/FLAT/ or HPF. Remember that you must
select the crossover function FIRST to get any adjustment. The range of adjustment is limited between 40-400Hz.
Output Clipping Indicator - This light indicates that the output of the amplifier is clipping. Use this light to help set gains.
(9) Bass EQ - This control adds 0 to +12dB of Bass boost at whatever BASS frequency has been chosen (40-100hZ). Be cautious when
adding boost fo some subwoofer systems as they may not be able to handle the additional low frequency boost.
RCA Input - The RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type
audio cables, keeping them away from power wiring wherever possible to reduce risk of noise.
(7 RCA Output - The RCA jacks allow for a normal Left and Right channel signal pass thru to a secondary amplifier. This is ONLY on
the SRPM700.2Dand SRPM700.4D
(2) BTR Port - (Bluetooth Receiver Port) This port is specifically to be used with any Cerwin-Vega Mobile Bluetooth controller.
This will allow direct plug in to the amplifier and control simple functions of music playback through the BTR receiver.
(3 Sub-Sonic Adjustment - This control allows you to remove the unwanted sub-sonic frequencies below the tuning frequency of
a ported enclosure. This helps to protect the woofer from over excursion.
Phase - This control gives the installer a unique feature that allows the variable adjusment of phase 0-180 degrees to
compensate for subwoofer placement. Allowing the subwoofer to sound like it's placed in the front of the vehicle instead of the trunk.
(5) Remote Level Control - All SRPM amplifers (except SRPM700.4D) have this port for the remote level control (included). The control is
intended to allow the user to control the level of gain up to the maximum adjustment level set on the amplifier for the subwoofer output. The
control does not add additional boost, it only attenuates the setting that is fixed at the amplifier's control panel.
Speaker Output Terminals - Connect your speakers to these terminals. Stereo connections are connected as labeled. Bridged
connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers will perform info 2 Ohm stereo loads or 4
Ohm bridged loads. DO NOT run 2 Ohm bridged loads on these amplifiers! The mono blocks will run 1 ohm mono.
(7) Power Input Connections - These connections are for input power, chassis ground, and remote turn-on. Use a minimum of
8 gauge wiring for power and ground connections. 4 Guage is recommended for the mono block. The terminals will handle up to 8 gauge wiring
with no problem whatsoever(4 guage on the mono block). Be sure any wiring that passes through metal has a grommet!
[5
FEATURES
©
HXM1200.1D :
- 12.5"/317.6mm |
HXM1100.6D |
E
£
©
o
=
N
un
ier |
A e a 2
e г ¿a EZ
[-=-1.75"/44.5mm -»]
SYSTEM CONFIGURATIONS
HXM800.2D
STEREO ( 1 AMP/4 SPEAKERS - 2 OHM LOAD)
HEAD UNIT
(perferredly with 5V output)
À
Pre-Outs from Headunit
(EEE
e
Switched 12 V Out
from Headunit
2 Channel HXM800.2D
(front panel connection)
HHHHH n° +
Rear Speakers(40)
Total speaker impedance
Total Speaker Impedance (MIN 2Q)
SYSTEM CONFIGURATIONS FUNCTIONS
HXM = 7C HAN N EL/8 SPEAKER MARI N = SYSTEM (1) Status LED's - These lights indicate when the amplifier is powered up normally and when there is a protection fault. The Protect
HXM800.2D _ 2 OH M STERE O FRONT /REAR LED is laminated when there is a problem with your amplifier. Please confact your authorize DA dealer or call DA's technical support.
HXMI 100.5D - 6 CHANNEL 4 OHM FRONT/ REAR/4 OHM MONO SUB (2) Input Gain Adjustment (SENS)- This control matches the preamp stage of the Diamond Audio amplifier to your source unit.
This is NOT a volume control. The range is between aprox 0.2mV and 10V. Using a cut up RCA cable you can run speaker level in.
DABTR10
SMARTPHONE (OR ANY DA
(BLUETOOTH) SOS ESE © Input Configuration - This switch parallels the input circuit if you are using a single stereo pair of outputs from your headunit
)) NN or from an auxiliary device (like a Smartphone, etc). The 6 channel model (HXM1100.6D) is set up to accept 2/4/and 6 channels of input.
К N 7 (4) Turn-On Mode Switch - This switch allow you to configure the “Turn-On Mode” switch for desired turn-on trigger. There are 3 modes
available are REM, DC and VOX. 1 - (REM) is the standard 12V trigger wire, 2 - (DC) or DC offset, when connected high level in, will sense
differences in ground in your wiring through the speaker leads and turn on amplifier, 3 - VOX (signal sensing) will sense any kind of signal
input info the amplifier RCA turning on the amplifier. Select VOX when using any Diamond Audio Bluetooth Controller.
| |
Tower System
connected to
2 Channel Amplifier
PreAmp Output Select - This switch allow you to select from which input you will use to be the ouput signal to the next amplifier
in the signal chain. For example for a 4 channel to a mono block to make a front/rear/sub system minimizing long RCA cables.
Crossover Selection Switch - This switch allow you to select the crossover function. HPF (High Pass Filter) LPF (Low Pass Filter) or FLAT
(no filter), HPF is for filtering out bass for midrange/mid bass drivers. LPF is for filktering out hogh frequencies for subwoofers The range of
adjustment is limited between 40-400Hz @12dB per octave (SRPM750,/1000,/1100.5D is 30-300 Hz @12dB per octave).
2 Channel HXM800.2D
(front panel connection) 7) Crossover Frequency Adjustment - Use this adjustment to select the crossover point LPF/FLAT/ or HPF. Remember that you must select
the crossover function FIRST to get any adjustment. The range of adjustment is limited between 40-400Hz (V1100.5D is 30-300 Hz).
Output Clipping Indicator - This light indicates that the output of the amplifier is clipping. Use this light to help set gains.
HXM&00.2D
DIAMOND
lw-1.75"/44.5mm =|
¢ Il =H =H IH H =H =H =H =H =H =H =H =H =H = = = = = = on
AEE = HE HE EH BH BH BH =H II I I II E BE IE BH = =m =
I}
. (9) Bass EQ - This control adds 0 to +18d8 of Bass boost at whatever BASS frequency has been chosen. Be cautious when
[e E RE QEU an an mn mn m adding boost to some subwoofer systems as they may not be able to handle the additional low frequency boost.
2ND AMP TURN-ON SETUP
Cabin System SPECIAL NOTE: © RCA Input - The RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit using RCA type
; И ected fa 6 2nd amplifer in a full BTR audio cables, keeping them away from power wiring wherever possible to reduce risk of noise.
annet Amp'ier seu er ¿so sie vk (D RCA Output - The RCA jacks allow for a normal Left and Right channel signal pass thru to a secondary amplifier. This is ONLY on
or ‘UL Tor Tle remote the HXM800.2Dand HXM800.4D
turn-on configuration
(see page 11)
® BTR Port - (Bluetooth Receiver Port) This port is specifically to be used with any Diamond Audio Bluetooth controller.
This will allow direct plug in to the amplifier and control simple functions of music playback through the BTR receiver.
6 Channel HXM1100.6D
(front panel connection)
ES (3 Sub-Sonic Adjustment - This control allows you to remove the unwanted sub-sonic frequencies below the tuning frequency of
a ported enclosure. This helps to protect the woofer from over excursion.
(9 Phase - This control gives the installer a unique feature that allows the variable adjusment of phase 0-180 degrees to
compensate for subwoofer placement. Allowing the subwoofer to sound like it's placed in the front of the vehicle instead of the trunk.
Remote Bass
y
© Remote Level Control - All HXM amplifers(except HXM800.4D) have this port for the remote level control (included). The control is
intended to allow the user to control the level of gain up to the maximum adjustment level set on the amplifier for the subwoofer output. The
control does not add additional boost, it only attenuates the setting that is fixed at the amplifier's control panel.
Speaker Output Terminals - Connect your speakers to these terminals. Stereo connections are connected as labeled. Bridged
connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers will perform into 2 Ohm stereo loads or 4
1to 4 Woofers Ohm bridged loads. DO NOT run 2 Ohm bridged loads on these amplifiers! The mono blocks will run 1 ohm mono.
(Min Impedence 2 Ohms TOTAL)
© Power Input Connections - These connections are for input power, chassis ground, and remote turn-on. Use a minimum of
8 gauge wiring for power and ground connections. 4 Guage is recommended for the mono block. The terminals will handle up fo 8 gauge wiring
1 with no problem whatsoever(4 guage on the mono block). Be sure any wiring that passes through metal has a grommet!
VEHICLE ELECTRICAL SYSTEM
Amplifiers (regardless of brand name) will put an increased load on the vehicle's battery and charging system. Diamond Audio 4 CHANNEL - HXM800.4D
recommends checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle 3 CHANNEL MODE
the increased load of your stereo system. Original equipment electrical systems which are in good condition should be able to
handle the extra load of any Diamond Audio amplifier without problems, although battery and alternator life can be reduced
depending on your individual listening habits. To maximize the performance of your amplifier, we suggest the use of a reserve
power "Stiffening”capacitor (1 Farad per T000W).
HEAD UNIT
(perferredly with 5V output)
Front/Rear
WARNING: Speaker setup
. . . . i. . (2 ohms on front channels)
Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power
wires carry substantial current and could radiate noise into the audio system through the audio cables.
—
. Plan the wire routing as described in the "Importance of Pre-Planning” section. Keep RCA cables close together but isolated
from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent
coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any 4 Channel HXM800.4D
metal barrier, protect them with plastic or rubber grommets fo prevent short circuits. Leave the wires long at this point to e PRE ae
adjust for a precise fit at a later time. |
2. Prepare the power wire for attachment to the amplifier FUSE WIRE DIAGRAM
by stripping 5/8 inch (15.9mm) of insulation from the — 7 eee >
end of the wire. Insert the bare wire into the B+
terminal And tighten the set screw to secure the cable
in place.
WARNING: Firewall
The B+ cable MUST be fused 18" or less from the N ел.
vehicle's posifive battery post. Choose a location fo \ A
install a waterproof fuseholder under the hood and
ensure connections are water fight. If you do not use
the appropriate fuseholder, the connectionwil | MR
eventually suffer corrosion from moisture and heat.
—X Switched 12 V Out
from Headunit
3. Trim the power cable within 18 inches (45.7mm)
of the positive battery post and splice in a infine '
fuse holder. DO NOT install the fuse at this fime. РА TTTT TT Rear Channels Bridged Mono
to 4 ohm woofer
4. Strip 1/2 inch (12.7mm) from the battery end
of the power cable. Crimp and soldier a large ring
terminal to the cable. Connect the ring terminal to
the positive (+) battery post.
Subwoofer(4 load)
Ground (-12V)
| |
SYSTEM CONFIGURATIONS INSTALLATION
5 CHANNEL -COMPLETE SYSTEM 5. Prepare the ground wire for attachment to the amplifier by stripping 5/8” of insulation from the end of the wire. Always
(HXM1100.6D) use a wire of the sume gauge as the power connection, never smaller. Insert the bare wire into the GND terminal and
" fighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface
HEAD UNIT and thoroughly clean the area of all dirt and grease. Strip the other end of the wire, crimp and solder a ring connector.
(perferredly with 5V output) Fasten the cable to the chassis using a non-anodized screw with a star washer and a nut.
WARNING: It is important to upgrade the ground FUSE CONNECTION DIAGRAM
connection between the negative (-) battery post and the - x
vehicle body or chassis to achieve optimum electrical
Front/Rear/Sub Pre-Outs
y € from Headunit
performance.
Switched 12 V Out
from Headunit 6. Prepare the REM turn-on wire for attachment fo the amplifier
by stripping 5/8 inch (15.9mm) of insulation from the end
of the wire. Insert the bare wire into the REM terminal and
fighten the set screw to secure the wire in place. Connect the
other end of the REM wire to a switched 12 volt positive
6 CHANNEL HXM1100.6D source. The switched voltage is usually taken from the *
(front panel connection) os . 800.2D = 40A
source unit's remote amp turn on lead. If the source unit 800.40 = 404%
does not have this output available, the recommended a
‘on is to wi inal i 800.10 = 450%
solution is to wire to an accessory terminal in the car's fuse : x
block using a relay to isolate the amplifer from the vehicles 1200.1D = 60A
accessory circuit. This however will turn the amplifier on and | 1100.6D = 60A*
off with the ignition key, regardless of whether the car stereo
is on or off.
A
N
| /. Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic
panels. Doing so may enable the screws to pull out from the panel due fo road vibration or sudden vehicle stops.
8. Connect from source signal by connecting the RCA audio cables to the input jacks at the amplifier.
Speaker level Input (Hi Level) RCA CONNECTION DIAGRAM
SPEAKER LEVEL INPUT (OPTIONAL): Г HEAD UNIT в
This is for OEM radios with NO RCA outputs, only speaker outputs. For и ЕВ © Ds
each speaker, or subwoofer, that you Jon to fio wit an ampli Since te HXM series ampfifiers can take speaker level a ул
channel, strip back a small part of your vehicle's color-coded left and right me empty bse a pone
speaker wires, then splice in the wires that lead to your amplifier. (Solder pel hel A. ich vi
or crimp, and secure the connection for optimum performance.) Sip th lel and right wires fo connectfo ,- -
! the OEM amplifier/Headunits speaker
outputs then plug directly into the HXM N J
Driving front seat speakers will require you to run wiring under a door
) ) 1e à . 9. Connect the car speakers. Speakers impedance should never be less than 2 Ohms stereo, 4 Ohms bridged.
jamb or the floor carpeting fo reach the speakers. Likewise, if your amp is
For most applications 18 gauge wire is adequate for the speaker leads. For leads in excess of ten feet, 16 gauge
RCA input harness. Just switch how
Turn-On works (REM/DC/VOX)
under efor seat, the front pa are pe ashi or the Hi 1 Once stippedos TT wire is recommended. Strip the speaker wires 1/2” (12.7mm) and insert info the speaker terminal block then tighten
ou your 5 ; VEUT LS LS OEM TAVIS EDEL | [hale he igh) 17 the set screw to secure into place. When wiring the speakers, pay careful attention to the polarity of the terminals on
SPEOKETS O7 0 SUDWOOTET. eos from your OBE, ~~ the speakers and make certain they correspond to the polarity on the amplifier. DO NOT chassis ground any of the
speaker leads as unstable operation or damage to the amplifier and/or speaker may result.
12] | 19
SYSTEM SETUP
Placing the x-over switch in the FULL position sets the amplifier to Full Range. This setting allows ALL frequencies to pass fo
the speakers. With the placing the switch in the HPF or LPF position activates the 7”
12dB crossover, adjustable from 40Hz - 400Hz. The 800.1D/1200.1D mono is
dedicated for Low Pass (LPF) only with an adjustable frequency from 30Hz - 300Hz. CM FREQ.
The 1100.6D (6 channel) amplifier offers full range (FULL) high pass (HPF)or low Lm]
pass (LPF) selector switch for channels 1-6. Channel HPE FLAT LPF
Placing the switch in the HPF position sets the amplifier to the High Pass Filter mode,
enabling frequencies above the cutoff point fo pass. Placing the switch in the LP
position sets the amplifier to the Low Pass Filter mode, enabling frequencies below the cutoff point to pass. For system tuning
begin with the frequency set at approximately 80Hz and fine tune up or down based on music choice and input level.
To adjust the gain setting, turn the amplifier gains all the way down (counterclockwise). If using a remote level control (ALL
HXM amplifiers but 800.4D), plug the level control ino the amplifier and turn it to about "HALF-WAY" (approx. the 12
0'clock position) this setups the bass boost so you can turn it UP ..OR...turn it DOWN when playing different music styles.
Next turn the source unit volume up to almost full volume (usually about 2 /3rds of the way up) or until the output starts to
distort on an oscilloscope. This will be NEARLY full volume on most source units, perhaps one or two “clicks” down from
maximum volume. Next, increase the amplifier gain setting until adequate volume is achieved, or unfil distortion is audible
and then turn it down a bit until the distortion is inaudible.
NOTE: Ideal signal to noise and dynamic range are achieved with the gain at minimum. Most users find adequate gain
and volume is achieved at less than halfway in the adjustment range. Avoid setting the amplifier gain very high as
noise and distortion will increase significantly. For a more in depth level setting (gain adjustment) procedure, visit the
Diamond Audio website.
The HPF or LPF crossover adjustment can now be fine tuned. If you are using the amplifier in a HPF configuration and would
like the system to be a little bit louder you can increase the HPF Filter frequency and reset the "Gain" of the amplifier. Raising
the HPF frequency up to high however will cause a loss of mid range and bass. If you are using the amplifier in a HP filter
configuration and you hear voice or vocals coming from your subwoofer system you can tum the LP Filter frequency down
(lower). After setting the input gain adjustment and crossover, you may choose to add a small amount of “Bass Boost” in
the low frequency region. There is both a Frequency selection (40-100Hz) AND how much boost (0-12dB). Remember that
the Bass Boost feature will not fix a poorly designed subwoofer enclosure or subwoofers that didn't sound good to begin with.
1. Make sure any bass EQ or low frequency equalization from the source unit is set to OFF or FLAT.
2. While playing the same musical selections used during the gain setting process, slowly increase the level of the Bass EQ.
You should be able to notice a change between 0 and +12dB. At the same time adjust frequency slowly from 40 -100Hz.
If you do not notice much difference, then it will not serve any benefit fo increase the boost further.
3. If the boost has audible benefits without adding appreciable distortion, find a level that suits your taste. Remember: it's
much easier to construct the right subwoofer enclosure for your listening preferences than relying on a bass boost control
fo do the job!
10 |
SYSTEM SETUP
e
40Hz I 007
4 TURN-ON OPTIONS - configure the “Turn-On Mode” switch for desired turn-on trigger. There are 3 modes available on the
HXM series amplifier, REM, DC and VOX. (REM) is the standard 12V trigger wire, (DC) or DC offset, when connected
high level in, will sense differences in ground in your wiring through the speaker leads and turn on amplifier, VOX (signal
sensing) will sense any kind of signal input into the amplifier RCA turning on the amplifier. Select VOX when using any
DIAMOND AUDIO Bluetooth Controller. The most preferred and reliable method is using the REM setting with a 12V
frigger wire connected to the vehicles ignition and will provide instant on and off for the amplifier. VOX and DC will
provide furn on capabilities for the amplifier when a 12V trigger wire is not available. These methods will have some
delay in turning the amplifier on and off.
“SWITCHED”
,
| |] | Co
"VOX" VOICE
ACTIVATED | o ON
|
i | MODE C
(signal sensing) | >
5. BTR Port — (Bluetooth Receiver Port) This port is specifically to be used with any DIAMOND AUDIO Bluetooth controller.
This will allow direct plug in to the amplifier and control simple functions of music playback through the BTR receiver. The
supplied cable is the ONLY cable that can be used to plug info the BTR port on the amplifier. Connecting any other
non-approved cable info the BTR port of the amplifier can cause damage to the amplifier and not be covered under
warranty. The BTR will pair to your phone or selected Bluetooth device and will allow playback through the amplifier to
speakers giving you unlimited install options. Play, Pause, Volume up/down, Track up/down, Pairing and Power on/off
of Bluetooth audio through this one solution. Once paired, the BTR will auto pair the last person paired to the controller
when it was powered down. The unit will remember up to 9 users and have memory without battery for up to 30 days.
When connecting a DIAMOND AUDIO controller using the BTR port select the turn on option to VOX.
BLUETOOTH RECEIVER (BTR) PORT
( \
DASH (CD) POWER
/ REAR MOUNT (CID) ©
; REMOTE IN (BLUE/WHITE STRIP) BTR PORT
PROTECT
с
с
с)
}
NOTE: MAKE SURE TO SET
“TURN-ON MODE” TO VOX
[11