KOBE Brand Range Hood
KOBE Brand Range Hood
Model No. CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
CH-191 SERIES – 9” HEIGHT
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
Important Safety Instructions ................................................................................................. 1
Components of Package ....................................................................................................... 3
Installation ............................................................................................................................. 4
Operation Instructions ......................................................................................................... 11
Maintenance........................................................................................................................ 12
Specifications ...................................................................................................................... 13
Measurements & Diagrams ................................................................................................. 14
Parts List ............................................................................................................................. 16
Circuit Diagram ................................................................................................................... 20
Disclaimer ........................................................................................................................... 22
Warranty ............................................................................................................................. 23
Product Registration ............................................................................................................ 25
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN
ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES.
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,
OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean fan, baffles/filters and grease laden surfaces frequently. To reduce the risk of fire and to
disperse air properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces,
attics, crawl spaces or garages.
NOTE
-
This warranty is invalid without an authorized agent’s
receipt or if unit is damaged due to misuse, poor
installation, improper use, mistreatment, negligence or any
other circumstances beyond the control of KOBE RANGE
HOODS authorized agents. Any repair carried out without
the supervision of KOBE RANGE HOODS authorized agents
will automatically void the warranty.
-
KOBE RANGE HOODS will not be held responsible f or any
damages to personal property or real estate or any bodily
injuries whether caused directly or indirectly by the range
hood.
WARNING – TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1) Keep fan, baffle/filter, if any, and grease-laden surfaces clean.
2) Always turn hood ON when cooking at high heat.
3) Use high settings on cooking range ONLY when necessary. Heat the oil slowly on low to medium
setting.
4) Do not leave cooking range unattended when cooking.
5) Always use cookware and utensils appropriate for the type and amount of food prepared.
6) Use this unit only in the manner intended by the manufacturer.
7) Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.
8) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan and baffles.
1
What to Do In The Event Of a Range Top Grease Fire
•
•
•
•
SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the
burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the
flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT
or 911.
NEVER PICK UP A BURNING PAN – You May Get Burned.
DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
•
•
•
Extinguish any open flame.
Do not try to turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company
and Fire Department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and
vapors.
2) To reduce the risk of fire, use only metal ductwork.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities. Activating
any switch on may cause ignition or an explosion.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of mercury,
which must be recycled or disposed of according to Local, State, and
Federal Codes.
2
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
RANGE HOOD BOX
ORIGINAL KIT – Model No. RA1020DC
(Sold Separately)
KOBE Range Hood - 1
Warranty Registration Card - 1
Instructions Manual - 1
Baffle Filter - 2 (for 30”, 36”, 42” hood)
KOBE Adjustable Duct Cover - 1
Screws Package – 1
Duct Cover-Mounting Bracket – 1
Hood-Mounting Bracket – 1
- 3 (for 48” hood)
Bottom Casing - 1 (for 30” hood)
- 3 (for 36” & 42” hood)
- 2 (for 48” hood)
7” Round Adapter – 1
Oil Tunnel – 1
OPTIONAL RECIRCULATING KIT – Model No. RA1020RD IS AVAILABLE.
FOR MORE INFORMATION, PLEASE CONTACT KOBE RANGE HOODS AT (626) 350-1355.
3
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.)
- FOR UNDER THE CABINET TABLE 1
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom (Recommended 27” to 30”)
D = Height of Hood
E = Height of the Cabinet
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) TABLE 2
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom (Recommended 27” to 30”)
D = Height of Hood
E = Height of Duct Cover [F – D]
F = Height of the Hood Installation
[A – (B+C)]
4
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS
NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD
MAY OCCUR.
Installation Contents
Under the Cabinet ................................................................................................................. 6
Stand Alone........................................................................................................................... 8
5
UNDER THE CABINET INSTALLATION
Figure 1
Preparation before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD,
PREVENT
DEBRIS
FROM
ENTERING THE VENT OPENING.
•
•
•
•
•
•
•
Decide the location of the venting pipe
from the hood to the outside. Refer to
Figure 1.
A straight, short venting run will allow
the hood to perform more efficiently.
Try to avoid as many transitions,
elbows, and long run as possible. This
may reduce the performance of the
hood.
Temporarily wire the hood to test for
proper operation before installing.
Important: Peel protective film off
the hood (if any).
For installing under the cabinet with
recessed bottom, attach 4-inch wide
wood filler strips (not included) on each
side. Refer to Figure 2.
Measure and create access opening for
electrical wires and 6” round plastic
exhaust under the cabinet.
Figure 2
.
Figure 3
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the power
on an electric range at the main electrical
box. SHUT OFF THE GAS BEFORE MOVING
A GAS RANGE.
1.
2.
3.
4.
Puncture the knockout holes on the hood
as shown in Figure 3.
Using references on Table 1 and
measurements on page 14 center the
hood in place beneath the cabinet and
flush with the front of the cabinet.
Draw electrical wires through cabinet
access opening.
From the bottom of the hood, place screw
(not provided) into the exact center of
each knockout hole. Make sure all screws
are in place before tightening screws.
CAUTION: MAKE
SURE THE HOOD IS SECURE BEFORE
RELEASING.
Figure 4
6
Figure 5
Ductwork Installation
5.
6.
Use aluminum or steel pipe to connect the
6” round plastic exhaust on the hood to
the ductwork above. Use duct tape to
make all joints secure and air tight. Refer
to Figure 4.
To convert ductwork to 7” round, attached
7” round adapter (provided) to the 6”
round plastic exhaust.
Wiring to Power Supply
SAFETY WARNING
Figure 6
RISK OF ELECTRICAL SHOCK.
THIS
RANGE HOOD MUST BE PROPERLY
GROUNDED. MAKE SURE THIS IS DONE
BY
SPECIALIZED
ELECTRICIAN
IN
ACCORDANCE WITH ALL APPLICABLE
NATIONAL AND LOCAL ELECTRICAL
CODES. BEFORE CONNECTING WIRES,
SWITCH POWER OFF AT SERVICE PANEL
AND LOCK SERVICE PANEL TO PREVENT
POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
7.
Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green
to green as shown on Figure 5.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. Make sure wires
do not slip between motor or any
moving parts to prevent any damage.
Figure 7
Accessories
8.
9.
10.
Attach oil tunnel. Refer to Figure 6.
Refer to Figure 7. Slide the baffle filter
into the hood. Push the baffle filter
upward.
Slide forward.
Pull
downward. Fit into place.
For bottom casing, repeat above steps.
Refer to page 15.
Final Assembly
11.
12.
Turn power ON in control panel. Check
all lights and fan operation.
Make sure to leave this manual for the
homeowner.
7
STAND ALONE INSTALLATION
***This installation only applied with the
purchase of a duct cover (Model No.
RA1020DC).
Figure 8
Preparation before Installation
NOTE:
TO AVOID DAMAGE TO YOUR
HOOD, PREVENT DEBRIS FROM
ENTERING THE VENT OPENING.
•
Decide the location of the venting pipe
from the hood to the outside. (Figure 1)
A straight, short venting run will allow
the hood to perform more efficiently.
Try to avoid as many transitions,
elbows, and long run as possible. This
may reduce the performance of the
hood.
Use duct tape to seal the joints between
pipe sections.
If necessary, prepare back wall frame
with cross framing lumber for secure
installation.
Using references on Table 2 and
measurements on page 13, decide the
level of the lumber. (Figure 2)
•
•
•
•
•
Figure 9
Hood Preparation before Installation
Figure 10
Temporarily wire the hood to test for
proper operation before installing.
• Important:
Peel protective film off
the hood and the duct cover (if any).
• If necessary, attach two rubber stands
(provided) with two (4 x 8 mm) screws
(provided) to the back of the hood.
• Attach the hood-mounting bracket to the
back of the hood with six (3/16” x 3/8”)
screws (provided) as shown In Figure
10.
•
Figure 11
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the power
on an electric range at the main electrical
box. SHUT OFF THE GAS BEFORE MOVING
A GAS RANGE.
1.
Using references on Table 2 and
measurements on page 14-15, mark the
leveling point of the hood. Position two
8
2.
3.
mounting screws (not provided) on the
wall, leaving 1/8” away from the wall.
Align hood-mounting bracket to the
screws on the wall and hook hood into
place as shown in Figure 11. Tighten
screws to secure hood to the wall.
For safety purposes, extra knockout holes
on the back of the hood are provided.
Knockout the holes. Remove the baffle
filters and attach screws to the wall by
accessing
underneath
the
hood.
CAUTION: MAKE SURE HOOD IS
SUCURE BEFORE RELEASING
Figure 12
Wiring to Power Supply
Figure 13
SAFETY WARNING
RISK OF ELECTRICAL SHOCK.
THIS
RANGE HOOD MUST BE PROPERLY
GROUNDED. MAKE SURE THIS IS DONE
BY
SPECIALIZED
ELECTRICIAN
IN
ACCORDANCE WITH ALL APPLICABLE
NATIONAL AND LOCAL ELECTRICAL
CODES. BEFORE CONNECTING WIRES,
SWITCH POWER OFF AT SERVICE PANEL
AND LOCK SERVICE PANEL TO PREVENT
POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
4.
Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green
to green as shown on Figure 12.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. Make sure wires
do not slip between motor or any
moving parts to prevent any damage.
Figure 14
Duct Cover Installation
5.
6.
Figure 15
Mark the position of the duct covermounting bracket. Use reference E from
Table 2 and measurements on page 1415.
Attach and secure duct covermounting bracket with two screws (not
provided). Refer to Figure 13. NOTE:
Inner duct cover will cover the duct covermounting bracket.
Use aluminum or steel pipe to connect the
plastic exhaust on the hood to the
ductwork above. Use duct tape to make
9
7.
8.
9.
10.
all joints secure and air tight as shown on
Figure 14.
To convert ductwork to 7” round, attached
7” round adapter (provided) to the 6”
round plastic exhaust.
Slide the inner duct cover up 2 inches
before sliding the entire duct cover onto
the hood. Refer to Figure 15.
Adjust the height of the inner duct cover to
the duct cover-mounting bracket. Secure
the inner duct cover with two (4x8 mm)
screws (provided).
Fasten outer duct cover to plastic plate on
the hood with four (4x8 mm) screws
(provided) as shown in Figure 16.
Figure 16
Figure 17
Accessories
11.
12.
13.
Attach oil tunnel. Refer to Figure 17.
Refer to Figure 18. Slide the baffle
filter into the hood. Push the baffle filter
upward.
Slide forward.
Pull
downward. Fit into place.
For bottom casing, repeat above steps.
Refer to page 15.
Final Assembly
14.
15.
Figure 18
Turn power ON in control panel. Check
all lights and fan operation.
Make sure to leave this manual for the
homeowner.
10
OPERATION INSTRUCTIONS
This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30second delay shutoff, two powerful centrifugal turbine impellers with baffle filters, and two bright 12-volt
20-watt halogen lights.
The four electronic controls are Light Control, Speed Control A, Speed Control B and the Power Control
(On/Off). Refer to Figure 19.
Figure 19
Light Control
Power Control
Speed Control B
Speed Control A
TURN ON:
•
Press Power Control (On/Off) button once.
(Note: If any control button is not pressed within 10 seconds, power will be automatically
turned off).
•
The KOBE hood will start on Low speed. Each press of the Speed Control button will
cycle through the various speeds.
•
Press Speed Control A button to cycle from Low, Medium, High, or QuietMode
.
Press Speed Control B button to cycle from Low, QuietMode
, High or Medium.
(Note: Speed Control A or B will operate both fans. These two speed buttons vary the
speed quicker.)
•
Press Light Control button to turn halogen light on.
TURN OFF:
•
Press Power Control (On/Off) button once, panel lights will flash and power will be
completely shut off after 30 seconds.
OR
•
•
Press Power Control (On/Off) button twice, all power will be shut off immediately.
If only the lights are on, pressing Power Control (On/Off) button once will turn power
off after 30 seconds.
11
MAINTENANCE
For the optimal level of operation, clean the range hood surface and baffles regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of
the hood. Avoid cleaner to get on the control switches. Only spread a light coating over the
surface of the hood and leave on for a few minutes (do not leave on too long or this may cause
damage to hood finish). Use soft towel to wipe off the cleaning solution, gently rubs any
stubborn spots. Use a slightly damp towel to get rid of any cleaning solution. Use dry soft towel
to dry the hood.
3. To bring the glow back into a stainless steel finish, use a stainless steel cleaner.
4. DO NOT allow deposits to remain for long periods of time.
5. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
causing rust.
6. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.
To Clean Baffle Filter/Oil Tunnel
CAUTION: DRAIN OIL FROM BAFFLE FILTER & OIL TUNNEL BEFORE OIL WILL OVERFLOW.
1. Remove all the baffle filters and oil tunnel.
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
(Note: Baffle Filters are top rack dishwasher safe.)
To Replace Light Bulb
CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL.
1. Make sure all controls are off, and range hood is unplugged.
2. Place the flat-headed screwdriver into the groove of the halogen light glass covering and the
housing.
3. Pop out the halogen light glass covering.
4. Gently pull out the defective light bulb and discard. Light bulbs should be 12V 20W maximum.
5. Using a cloth, hold the new light bulb and push securely into light socket.
6. Return halogen light glass cover to the housing.
7. Turn range hood ON to test for operation.
12
SPECIFICATIONS
MODEL / SIZE
CH9130SQB / 30”
CH9136SQB / 36"
CH9142SQB / 42”
CH9148SQB / 48”
COLOR
# 304 Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
CH9130SQB – 232W / 2.21A
CH9136SQB – 232W / 2.21A
CH9142SQB – 253W / 2.38A
CH9148SQB – 258W / 2.41A
VOLTAGE
120V 60Hz
NUMBER OF MOTORS
2
DESIGN
18-Gauge Seamless / Satin Finish
FAN TYPE
Twin Turbine Impeller
EXHAUST
Top 6” Round
Top 7” Round Adapter
CONTROLS
Electronic Control (4 Buttons) –
10-Second Standby Startup
30-Second Delay Shutoff
HALOGEN LIGHTS
CH9130SQB - 12V 20W x 2
CH9136SQB - 12V 20W x 2
CH9142SQB - 12V 20W x 3
CH9148SQB - 12V 20W x 3
HOOD DIMENSION
(W x D x H)
(CH9130SQB)
(CH9136SQB)
(CH9142SQB)
(CH9148SQB)
OPTIONAL ACCESSORIES
(W x D x H)
1) Original Kit - Model No. RA1020DC
Adjustable Duct Cover 10-5/8” x 9-1/8” x (20-5/8” ~ 39-5/8”)
2) Recirculating Kit - Model No. RA1020RD
Adjustable Recirculating Duct Cover 10-5/8” x 9-1/8” x (21” ~ 36”)
3) Model No. SSP30
30” Stainless Steel Back Panel 30” x 1/10” x 32”
4) Model No. SSP36
36” Stainless Steel Back Panel 36” x 1/10” x 32”
WEIGHT (lbs)
SPEED
Air Capacity (cfm)*
Sone
29-3/4” x
35-3/4” x
41-3/4” x
47-3/4” x
22” x
22” x
22” x
22” x
9-1/8”
9-1/8”
9-1/8”
9-1/8”
Net
53.0
59.0
68.0
77.0
(CH9130SQB)
(CH9136SQB)
(CH9142SQB)
(CH9148SQB)
QuietMode

280
1.2*
Low
450
2.0
*In House Test Static Pressure “0”. One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications information is subject to change without notice.
13
Gross
68.0
77.0
88.0
101.0
Medium
580
2.8
High
800
4.5
MEASUREMENTS & DIAGRAMS
All measurements in ( ) are millimeters.
All inch measurements are converted from millimeters. Inch
measurements are estimated.
- FOR UNDER THE CABINET MODEL NO.:
CH9130SQB
MODEL NO.:
CH9136SQB
CH9142SQB
CH9148SQB
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) -
***Hood-Mounting Bracket
***Duct Cover-Mounting Bracket
14
***Rear Knockout Holes
MODEL NO.:
CH9130SQB
MODEL NO.:
15
CH9136SQB
CH9142SQB
CH9148SQB
PARTS LIST
MODEL NO.:
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
NO.
1
2
3
4
DESCRIPTION
7” Round Adapter
6” Round Plastic Exhaust
Plastic Plate
Hood Casing
5
6
7
8
9
10
A
Halogen Light Unit (12V 20W Max.)
Control Unit
Control Board
Transformer Support
Transformer (Motor)
Air Chamber
Air Chamber (Top)
B
Air Chamber (Side)
11
Transformer (Light)
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
A
B
27
MODEL /SIZE
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
Capacitor
Processor Board Box
Processor Board
Screw (1/8” x 3/8”)
Screw (TS 1/4 x 7/16)
Motor (Right)
Motor (Left)
Turbine Impeller (Right)
Turbine Impeller (Left)
Oil Tunnel Seal
Oil Tunnel
Impeller Plastic Cover
Safety Screen
Safety Screen Screw
Bottom Casing
4” Wide
3” Wide
5-1/4” Wide
4-1/2” Wide
4” Wide
Baffle Filter
PART NO.
C1-0505-0004
C1-0505-0001
C1-0507-0201
10-1930A
10-1936A
10-1942A
10-1948A
C1-0403-0101
C1-0501-0101
C1-0404-0401-A
C1-0201-1930
C1-0402-A120-01
C1-0101-0880
C1-0101-0880
C1-0101-1542
C1-0101-1542
C1-0102-1930
C1-0102-1930
C1-0102-1942
C1-0102-1942
C1-0402-0120-40
C1-0402-0120-60
C1-0401-0120-01A
C1-0501-0102
C1-0404-0401-B
C1-0708-0003
C1-0703-0001
C1-0301-0120-17A
C1-0301-0120-18A
C1-0251-0880-01
C1-0251-0880-02
C1-0502-0301
C1-0502-0203
C1-0251-0001
C1-0602-0103
C1-0705-0001
CH9130SQB
CH9136SQB
CH9142SQB
CH9148SQB
CH9136SQB
16
B101-1930-09
B101-1936-09
B101-1942-09
B101-1948-09
B101-1930-09
B101-1930-15
(Optional Duct Cover)
ORIGINAL KIT
NO.
DESCRIPTION
01
Duct Cover-Mounting Bracket
02
Screw (TS 4 x 8 mm)
03
Duct Cover
04
Hood-Mounting Bracket
05
Screw (3/16” x 3/8”)
06
Rubber Stand
07
Screw (TS 4 x 8 mm)
MODEL /SIZE
RA1020DC
RECIRCULATING KIT
NO.
DESCRIPTION
01
Duct Cover-Mounting Bracket
02
T-Head Box
A
Box
B
Box Bracket
03
Screw (TS 4 x 8 mm)
04
Recirculating Duct Cover
05
6” Round Plastic Exhaust
06
Aluminum Pipe
07
Charcoal Filter
08
Screw (3/16” x 1”)
09
Hood-Mounting Bracket
10
Screw (3/16” x 3/8”)
11
Rubber Stand
12
Screw (TS 4 x 8 mm)
MODEL /SIZE
RA1020RD
17
PART NO.
C1-0203-0002
C1-0708-0006
12-02000-430-51
C1-0221-0330
C1-0707-0001
C1-0511-0201
C1-0708-0006
PART NO.
C1-0203-0002
C1-0241-1930-FA
C1-0241-1930-FB
C1-0708-0006
12-02000-430-51F
C1-0505-0001
C1-0601-0004
C1-0603-0302
C1-0707-0003
C1-0203-0330
C1-0707-0001
C1-0511-0201
C1-0708-0006
MODEL NO.:
CH9130SQB
CH9136SQB
18
MODEL NO.:
CH9142SQB
CH9148SQB
19
CIRCUIT DIAGRAM
MODEL NO.:
CH9130SQB
CH9136SQB
20
MODEL NO.:
CH9142SQB
CH9148SQB
21
DISCLAIMER
1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE
ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND
SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM.
Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the
carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The
carrier will furnish you with necessary forms for filing a claim.
DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY.
2. PLEASE INSPECT CONTENTS OF PACKAGE (S) CAREFULLY UPON RECEIPT!
We must be notified in writing of any damages and/or missing parts within the allocated days upon
your receipt of package(s). Contact your local KOBE dealer or distributor or call KOBE for the time
limit.
CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS.
NOTE: ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY
BEFORE SHIPPING.
3. Products must be returned in good working condition with ALL original parts and documentation
packed in ALL original cartons, fillers and shipping cartons. A restocking fee of 25% will be charged
for all approved items.
EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING.
4. MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE
INSTALLATION. Appearance flaws of the hood found after installation and not affecting hood
performance is not covered under our warranty for returns or exchanges. Service visits not covered
under warranty will carry a service charge.
A)
Before Installation: Return for exchange or refund (please see above for acceptable
returns).
B)
After Installation: NO exchange or refund.
22
WARRANTY
WARRANTY CERTIFICATE
KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects
in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two
years from the date of purchase and to the repair or replacement at its option and subject to the terms
and conditions stated below, of any component part, which its examination shall disclose to be so
defective.
TWO-YEAR WARRANTY SERVICE PERIOD
Any covered failure occurring within two years of original purchase arising from defective workmanship
or material in manufacture will be repaired (or at our option the unit will be replaced) free of charge by
an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of
purchase (or original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new owner is
protected until expiration of the original purchaser’s warranty.
CONDITIONS
The following conditions apply only in relation to the warranty expressly given in this certificate.
1) This warranty applies only:
a) within U.S.A. and Canada.
b) to range hoods used for PRIVATE SINGLE FAMILY USE (if used for COMMERCIAL or
MULTIPLE FAMILY USE or other purposes, warranty will be voided).
2) Repair of any fault to be provided under this warranty shall not be provided:
a) if the identification number attached to the range hood has been altered, rendered illegible or
removed;
b) if notice of the defect has not been given within the period applicable;
c) for failure of light bulbs;
d) for physical damage;
e) for surfaces damaged by use of improper chemical cleaning agents;
f) if the appliance has been:
i) subject to misuse, abuse, negligence, accident, incorrect installation or failure to follow the
operating instructions;
ii) connected to improper, inadequate or faulty electricity service or exhaust ducts or flues or
operated using incorrect or contaminated lubricants;
iii) installed, maintained or operated otherwise than in accordance with the instructions
furnished by KOBE Range Hoods including the improper use of detergents, bleaches, or
cleaners.
g) for damage to range hood during transit, delivery, installation or removal;
h) for damage by or resulting from attempted repairs conducted by anyone other than our
Authorized Service Agent.
3) The purchaser shall be responsible for any expenses involved in making the range hood readily
accessible for servicing and where the range hood is installed outside the main sales territory of the
retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable, for any
23
traveling expenses and any costs of transporting the range hood or parts thereof to and from the
dealer or Service Agent
4) The purchaser must produce proof of purchase together with this warranty certificate when making
the claim.
5) Damages caused during shipment are not covered under our warranty.
CONSEQUENTIAL DAMAGE
The warrantor is not responsible for any consequential damage. SOME STATES DO NOT ALLOW
THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY
TO YOU.
IMPLIED WARRANTIES/STATE LAW
Any implied warranties, including the implied warranty of merchantability and fitness for purpose,
imposed on the sale by the laws of the state of sale are limited to two year from the date of original
purchase. Some states do not allow limitations on the duration of implied warranties. This warranty
gives you specific legal rights, and may also have rights, which vary from state to state.
SERVICE
For service contact:
KOBE Range Hoods
10505 Valley Blvd, Suite 302
EI Monte, CA 91731
U.S.A
Tel: (626) 350-1355 Fax: (626) 350-1976
Email:
[email protected]
Website:
www.KOBERangeHoods.com
24
PRODUCT REGISTRATION
Register Your Product!
Any covered failure occurring within two years of original purchase arising from defective
workmanship or material in manufacture will be repaired or at our option the unit will be replaced
free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable.
Keep proof of purchase (original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new owner is
protected until expiration of the original purchaser’s warranty. See warranty section for complete
warranty coverage information.
This appliance has been manufactured, tested, and inspected to the standards required by KOBE
Range Hoods.
PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE
TO:
KOBE Range Hoods
10505 Valley Blvd Suite # 302
El Monte, CA 91731 USA
RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD:
Model No. ________________________
Serial No. ________________________
Purchased Date
_____/_____/_____
Purchased From:
______________________________
______________________________
______________________________
IMPORTANT: PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN
REQUESTING FOR SERVICE.
v.071016
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement