Ditch Witch 1030 Service manual
Ditch Witch 1030 is a versatile and powerful piece of equipment designed to make your drilling operations more efficient and productive. With its advanced features and capabilities, the 1030 provides enhanced control, precision, and safety for various applications in the construction, utility, and landscaping industries.
Advertisement
Advertisement
1030/1230 - SERVICE
SERIAL NUMBER RECORD
SERVICE
1
SERIAL NUMBER RECORD
Record serial numbers and date of purchase in spaces provided.
Serial number plate is mounted to frame behind right wheel.
1030/1230 - SERVICE
SERIAL NUMBER RECORD
SERVICE
1
SERIAL NUMBER RECORD
Record serial numbers and date of purchase in spaces provided.
Serial number plate is mounted to frame behind right wheel.
Date of purchase
Serial number
Engine serial number
Date of purchase
Serial number
Engine serial number
2
1030/1230 - SERVICE
SUPPORT PROCEDURE
SUPPORT PROCEDURE
Notify your dealer immediately of any malfunction or failure of
Ditch Witch equipment.
Always give model, serial number, and approximate date of equipment purchase. This information should be recorded and placed on file by owner at time of purchase.
Return damaged parts to dealer for inspection and warranty consideration.
Order genuine Ditch Witch replacement parts from your authorized Ditch Witch dealer. Use of another manufacturer’s parts may void warranty.
RESOURCES
Publications
Contact your Ditch Witch dealer for publications covering operation, service, and repair of your equipment.
Ditch Witch Training
For information about on-site, individualized training, contact your
Ditch Witch dealer.
2
1030/1230 - SERVICE
SUPPORT PROCEDURE
SUPPORT PROCEDURE
Notify your dealer immediately of any malfunction or failure of
Ditch Witch equipment.
Always give model, serial number, and approximate date of equipment purchase. This information should be recorded and placed on file by owner at time of purchase.
Return damaged parts to dealer for inspection and warranty consideration.
Order genuine Ditch Witch replacement parts from your authorized Ditch Witch dealer. Use of another manufacturer’s parts may void warranty.
RESOURCES
Publications
Contact your Ditch Witch dealer for publications covering operation, service, and repair of your equipment.
Ditch Witch Training
For information about on-site, individualized training, contact your
Ditch Witch dealer.
1030/1230 - FOREWORD
FOREWORD
This manual is an important part of your equipment. It provides safety information and operation instructions to help you use and maintain your Ditch Witch equipment.
Read this manual before using your equipment. Keep it with the equipment at all times for future reference. If you sell your equipment, be sure to give this manual to the new owner.
If you need a replacement copy, contact your Ditch Witch dealer.
If you need assistance in locating a dealer, visit our website at
www.ditchwitch.com or write to the following address:
The Charles Machine Works, Inc.
Attn: Marketing Department
PO Box 66
Perry, OK 73077-0066
USA
The descriptions and specifications in this manual are subject to change. The Charles Machine Works, Inc. reserves the right to improve equipment. Some product improvements may have taken place after this manual was published. For the latest information on Ditch Witch equipment, see your Ditch Witch dealer.
Thank you for buying and using Ditch Witch equipment.
3 1030/1230 - FOREWORD
FOREWORD
This manual is an important part of your equipment. It provides safety information and operation instructions to help you use and maintain your Ditch Witch equipment.
Read this manual before using your equipment. Keep it with the equipment at all times for future reference. If you sell your equipment, be sure to give this manual to the new owner.
If you need a replacement copy, contact your Ditch Witch dealer.
If you need assistance in locating a dealer, visit our website at
www.ditchwitch.com or write to the following address:
The Charles Machine Works, Inc.
Attn: Marketing Department
PO Box 66
Perry, OK 73077-0066
USA
The descriptions and specifications in this manual are subject to change. The Charles Machine Works, Inc. reserves the right to improve equipment. Some product improvements may have taken place after this manual was published. For the latest information on Ditch Witch equipment, see your Ditch Witch dealer.
Thank you for buying and using Ditch Witch equipment.
3
4
1030/1230 - FOREWORD 4
1030/1230 - FOREWORD
Operator's Manual
Issue Number 4.2/OP-11/04
Part Number 054-515
Copyright 1997, 1999, 2001, 2003, 2004 by The Charles Machine Works, Inc.,
Perry, Oklahoma
, Ditch Witch, CMW, AutoCrowd,
Modularmatic, Jet Trac, Roto Witch, Subsite, Fluid Miser, Perma-
Soil, Power Pipe, Super Witch, Super Witch II, Pierce Airrow, The
Underground, and The Underground Authority Worldwide are registered trademarks of The Charles Machine Works, Inc.
Operator's Manual
Issue Number 4.2/OP-11/04
Part Number 054-515
Copyright 1997, 1999, 2001, 2003, 2004 by The Charles Machine Works, Inc.,
Perry, Oklahoma
, Ditch Witch, CMW, AutoCrowd,
Modularmatic, Jet Trac, Roto Witch, Subsite, Fluid Miser, Perma-
Soil, Power Pipe, Super Witch, Super Witch II, Pierce Airrow, The
Underground, and The Underground Authority Worldwide are registered trademarks of The Charles Machine Works, Inc.
1030/1230 - CONTENTS
CONTENTS
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Serial Number Record . . . . . . . . . . . . . . . . . . . . . . . . . 1
Support Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Control Console Overview . . . . . . . . . . . . . . . . . . . . . . 9
Control Console Descriptions . . . . . . . . . . . . . . . . . . 10
Engine Controls Overview . . . . . . . . . . . . . . . . . . . . . 13
Engine Controls Descriptions . . . . . . . . . . . . . . . . . . . 14
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Underground Hazards . . . . . . . . . . . . . . . . . . . . . . . . 16
Emergency Procedures . . . . . . . . . . . . . . . . . . . . . . . 17
Jobsite Classification . . . . . . . . . . . . . . . . . . . . . . . . . 20
Safety Alert Classifications . . . . . . . . . . . . . . . . . . . . 24
Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5 1030/1230 - CONTENTS
CONTENTS
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Serial Number Record . . . . . . . . . . . . . . . . . . . . . . . . . 1
Support Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Control Console Overview . . . . . . . . . . . . . . . . . . . . . . 9
Control Console Descriptions . . . . . . . . . . . . . . . . . . . 10
Engine Controls Overview. . . . . . . . . . . . . . . . . . . . . . 13
Engine Controls Descriptions . . . . . . . . . . . . . . . . . . . 14
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Underground Hazards . . . . . . . . . . . . . . . . . . . . . . . . 16
Emergency Procedures . . . . . . . . . . . . . . . . . . . . . . . 17
Jobsite Classification . . . . . . . . . . . . . . . . . . . . . . . . . 20
Safety Alert Classifications . . . . . . . . . . . . . . . . . . . . . 24
Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5
6
1030/1230 - CONTENTS
TRANSPORTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tiedown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Haul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Freewheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Tow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Daily Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Trenching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
LUBRICATION AND MAINTENANCE . . . . . . . . . . . . . . . 47
Lubrication Overview . . . . . . . . . . . . . . . . . . . . . . . . . 48
Lubrication Schedule . . . . . . . . . . . . . . . . . . . . . . . . . 49
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . 56
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6
1030/1230 - CONTENTS
TRANSPORTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tiedown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Haul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Freewheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Tow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Daily Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Trenching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
LUBRICATION AND MAINTENANCE . . . . . . . . . . . . . . . 47
Lubrication Overview . . . . . . . . . . . . . . . . . . . . . . . . . 48
Lubrication Schedule . . . . . . . . . . . . . . . . . . . . . . . . . 49
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . 56
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
1030/1230 - OVERVIEW
OVERVIEW
The Ditch Witch 1030 and 1230 pedestrian trenchers are designed for easy, efficient use.
Color-coded controls are within easy reach of the operator.
These compact units fit through most standard yard gates, and the machines are balanced for easy jobsite maneuvering. A choice of a 24”, 30”, or 36” (610-, 760-, or 915-mm) digging boom, along with several chain options, make these machines flexible enough for most soil conditions. The axle lock feature aids smooth, easy turns and straight trenching.
7 1030/1230 - OVERVIEW
OVERVIEW
The Ditch Witch 1030 and 1230 pedestrian trenchers are designed for easy, efficient use.
Color-coded controls are within easy reach of the operator.
These compact units fit through most standard yard gates, and the machines are balanced for easy jobsite maneuvering. A choice of a 24”, 30”, or 36” (610-, 760-, or 915-mm) digging boom, along with several chain options, make these machines flexible enough for most soil conditions. The axle lock feature aids smooth, easy turns and straight trenching.
7
1.
Trail wheel
2.
Digging boom and chain
3.
Engine
4.
Operator station
1.
Trail wheel
2.
Digging boom and chain
3.
Engine
4.
Operator station
8
1030/1230 - OVERVIEW 8
1030/1230 - OVERVIEW
1030/1230 - CONTROLS
CONTROL CONSOLE OVERVIEW
CONTROLS
9
CONTROL CONSOLE OVERVIEW
1030/1230 - CONTROLS
CONTROL CONSOLE OVERVIEW
CONTROLS
9
CONTROL CONSOLE OVERVIEW
1.
Bail
2.
Digging boom control (green)
3.
Axle lock (blue)
4.
Speed/direction control (orange)
5.
Throttle (black)
6.
Digging chain control (yellow)
7.
Power switch
1.
Bail
2.
Digging boom control (green)
3.
Axle lock (blue)
4.
Speed/direction control (orange)
5.
Throttle (black)
6.
Digging chain control (yellow)
7.
Power switch
10
1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
CONTROL CONSOLE DESCRIPTIONS
Bail
This start interlock control engages and disengages hydraulic system.
• Move down into handlebar to engage.
• Release to disengage.
Axle Lock (Blue)
This lever locks or unlocks axle.
• Push to unlock. Use unlocked axle to manuever trencher.
• Pull to lock. Use locked axle for straight trenching and driving over rough terrain.
ic1034.tif
Digging Boom Control (Green)
This lever raises or lowers digging boom when bail is engaged.
• Push to lower boom.
• Pull to raise boom.
ic0127h.eps
10
1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
CONTROL CONSOLE DESCRIPTIONS
Bail
This start interlock control engages and disengages hydraulic system.
• Move down into handlebar to engage.
• Release to disengage.
Axle Lock (Blue)
This lever locks or unlocks axle.
• Push to unlock. Use unlocked axle to manuever trencher.
• Pull to lock. Use locked axle for straight trenching and driving over rough terrain.
ic1034.tif
Digging Boom Control (Green)
This lever raises or lowers digging boom when bail is engaged.
• Push to lower boom.
• Pull to raise boom.
ic0127h.eps
1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
Digging Chain Control (Yellow)
This lever starts digging chain when bail is engaged.
• Push to start digging chain.
• Returns to neutral and digging chain stops when bail is released.
ic0014c.tif
Speed/Direction Control
(Orange)
This lever controls unit speed and direction when bail is engaged.
• Ensure control is in BAIL
RELEASE (neutral) position, and engage bail.
• Push to move forward.
• Pull to move backward.
ic0013c.tif
• Move farther from center to go faster in either direction.
• Return to BAIL RELEASE (neutral) to stop.
11 1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
Digging Chain Control (Yellow)
This lever starts digging chain when bail is engaged.
• Push to start digging chain.
• Returns to neutral and digging chain stops when bail is released.
ic0014c.tif
Speed/Direction Control
(Orange)
This lever controls unit speed and direction when bail is engaged.
• Ensure control is in BAIL
RELEASE (neutral) position, and engage bail.
• Push to move forward.
• Pull to move backward.
ic0013c.tif
• Move farther from center to go faster in either direction.
• Return to BAIL RELEASE (neutral) to stop.
11
12
1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
Throttle (Black)
This lever controls engine speed.
Increasing engine speed also increases digging chain speed.
• Push down to speed engine.
• Pull up to slow engine.
ic0128h.eps
Power Switch
This two-position switch controls power to the machine.
• Turn clockwise to turn power on. In this position, engine will start when rope start is pulled.
• Turn counterclockwise to stop engine.
12
1030/1230 - CONTROLS
CONTROL CONSOLE DESCRIPTIONS
Throttle (Black)
This lever controls engine speed.
Increasing engine speed also increases digging chain speed.
• Push down to speed engine.
• Pull up to slow engine.
ic0128h.eps
Power Switch
This two-position switch controls power to the machine.
• Turn clockwise to turn power on. In this position, engine will start when rope start is pulled.
• Turn counterclockwise to stop engine.
1030/1230 - CONTROLS
ENGINE CONTROLS OVERVIEW
ENGINE CONTROLS OVERVIEW
13 1030/1230 - CONTROLS
ENGINE CONTROLS OVERVIEW
ENGINE CONTROLS OVERVIEW
13
1.
Fuel shut-off valves
2.
Choke
3.
Pull start
1.
Fuel shut-off valves
2.
Choke
3.
Pull start
14
1030/1230 - CONTROLS
ENGINE CONTROLS DESCRIPTIONS
ENGINE CONTROLS DESCRIPTIONS
Fuel Shut-off Valves
Two valves separate fuel reservoir from engine.
• Close when transporting unit to or from jobsite.
• Open before starting engine.
Choke
This valve regulates air/fuel mixture. Close valve to help start cold engine.
Pull Start
Cranks engine for starting.
• Ensure that power switch is on and fuel shut-off valves are open.
• Pull to start engine.
If engine does not start after three pulls, turn power switch off and check for fuel blockage or electrical system problems.
14
1030/1230 - CONTROLS
ENGINE CONTROLS DESCRIPTIONS
ENGINE CONTROLS DESCRIPTIONS
Fuel Shut-off Valves
Two valves separate fuel reservoir from engine.
• Close when transporting unit to or from jobsite.
• Open before starting engine.
Choke
This valve regulates air/fuel mixture. Close valve to help start cold engine.
Pull Start
Cranks engine for starting.
• Ensure that power switch is on and fuel shut-off valves are open.
• Pull to start engine.
If engine does not start after three pulls, turn power switch off and check for fuel blockage or electrical system problems.
1030/1230 - SAFETY
15
SAFETY
Follow these guidelines before operating any jobsite equipment:
• Complete proper training and read operator’s manual before using equipment.
• Contact One-Call (888-258-0808) and any utility companies which do not subscribe to One-Call. Have all underground pipes and cables located and marked before operating equipment. If you damage a utility, contact utility company.
• Classify jobsite based on its hazards and use correct tools and machinery, safety equipment, and work methods for jobsite.
• Mark jobsite clearly and keep spectators away.
• Wear personal protective equipment.
• Review jobsite hazards, safety and emergency procedures, and individual responsibilities with all personnel before work begins. Safety videos are available from your Ditch Witch dealer.
• Replace missing or damaged safety shields and safety signs.
• Use equipment carefully. Stop operation and investigate anything that does not look or feel right.
• Do not operate unit where flammable gas is present.
• Contact your Ditch Witch dealer if you have any question about operation, maintenance, or equipment use.
1030/1230 - SAFETY
15
SAFETY
Follow these guidelines before operating any jobsite equipment:
• Complete proper training and read operator’s manual before using equipment.
• Contact One-Call (888-258-0808) and any utility companies which do not subscribe to One-Call. Have all underground pipes and cables located and marked before operating equipment. If you damage a utility, contact utility company.
• Classify jobsite based on its hazards and use correct tools and machinery, safety equipment, and work methods for jobsite.
• Mark jobsite clearly and keep spectators away.
• Wear personal protective equipment.
• Review jobsite hazards, safety and emergency procedures, and individual responsibilities with all personnel before work begins. Safety videos are available from your Ditch Witch dealer.
• Replace missing or damaged safety shields and safety signs.
• Use equipment carefully. Stop operation and investigate anything that does not look or feel right.
• Do not operate unit where flammable gas is present.
• Contact your Ditch Witch dealer if you have any question about operation, maintenance, or equipment use.
16
1030/1230 - SAFETY
ACCESSORIES
ACCESSORIES
Fire Extinguisher
If required, a fire extinguisher should be mounted near the power unit but away from possible points of ignition. The fire extinguisher should always be classified for both oil and electric fires. It should meet legal and regulatory requirements.
Lighting Kit
If you need additional light, plug lighting kit into provided outlet.
Contact your Ditch Witch dealer for further information.
UNDERGROUND HAZARDS
Striking underground hazards can cause explosion, electrocution, fire, and exposure to hazardous materials.
Hazards include:
• Electric lines
• Natural gas lines
• Fiber optic cables
• Water lines
• Sewer lines
• Pipes carrying other chemicals, liquids, or gases
• Storage tanks
16
1030/1230 - SAFETY
ACCESSORIES
ACCESSORIES
Fire Extinguisher
If required, a fire extinguisher should be mounted near the power unit but away from possible points of ignition. The fire extinguisher should always be classified for both oil and electric fires. It should meet legal and regulatory requirements.
Lighting Kit
If you need additional light, plug lighting kit into provided outlet.
Contact your Ditch Witch dealer for further information.
UNDERGROUND HAZARDS
Striking underground hazards can cause explosion, electrocution, fire, and exposure to hazardous materials.
Hazards include:
• Electric lines
• Natural gas lines
• Fiber optic cables
• Water lines
• Sewer lines
• Pipes carrying other chemicals, liquids, or gases
• Storage tanks
1030/1230 - SAFETY
EMERGENCY PROCEDURES
17
EMERGENCY PROCEDURES
Before operating any equipment, review emergency procedures and check that all safety precautions have been taken.
EMERGENCY SHUTDOWN - Turn ignition switch to stop position or push remote engine stop button.
Electric Strike Description
When working near electric cables, remember the following:
• Electricity follows all paths to ground, not just path of least resistance.
• Pipes, hoses, and cables will conduct electricity back to all equipment.
• Low voltage current can injure or kill. Almost one-third of work-related electrocutions result from contact with less than
440 volts.
Most electric strikes are not noticeable, but indications of a strike include:
• power outage
• smoke
• explosion
• popping noises
• arcing electricity
If any of these occur, assume an electric strike has occurred.
1030/1230 - SAFETY
EMERGENCY PROCEDURES
17
EMERGENCY PROCEDURES
Before operating any equipment, review emergency procedures and check that all safety precautions have been taken.
EMERGENCY SHUTDOWN - Turn ignition switch to stop position or push remote engine stop button.
Electric Strike Description
When working near electric cables, remember the following:
• Electricity follows all paths to ground, not just path of least resistance.
• Pipes, hoses, and cables will conduct electricity back to all equipment.
• Low voltage current can injure or kill. Almost one-third of work-related electrocutions result from contact with less than
440 volts.
Most electric strikes are not noticeable, but indications of a strike include:
• power outage
• smoke
• explosion
• popping noises
• arcing electricity
If any of these occur, assume an electric strike has occurred.
18
1030/1230 - SAFETY
EMERGENCY PROCEDURES
If an Electric Line is Damaged
If you suspect an electric line has been damaged and you are on
tractor, DO NOT MOVE. Remain on tractor and take the following actions. The order and degree of action will depend upon the situation.
• Warn people nearby that an electric strike has occurred.
Instruct them to leave the area and contact utility.
• Raise attachments and drive from immediate area.
• Contact utility company to shut off power.
• Do not return to jobsite or allow anyone into area until given permission by utility company.
If you suspect an electric line has been damaged and you are off
tractor, DO NOT TOUCH TRACTOR. Take the following actions.
The order and degree of action will depend upon the situation.
• LEAVE AREA.
• Contact utility company to shut off power.
• Do not return to jobsite or allow anyone into area until given permission by utility company.
18
1030/1230 - SAFETY
EMERGENCY PROCEDURES
If an Electric Line is Damaged
If you suspect an electric line has been damaged and you are on
tractor, DO NOT MOVE. Remain on tractor and take the following actions. The order and degree of action will depend upon the situation.
• Warn people nearby that an electric strike has occurred.
Instruct them to leave the area and contact utility.
• Raise attachments and drive from immediate area.
• Contact utility company to shut off power.
• Do not return to jobsite or allow anyone into area until given permission by utility company.
If you suspect an electric line has been damaged and you are off
tractor, DO NOT TOUCH TRACTOR. Take the following actions.
The order and degree of action will depend upon the situation.
• LEAVE AREA.
• Contact utility company to shut off power.
• Do not return to jobsite or allow anyone into area until given permission by utility company.
1030/1230 - SAFETY
EMERGENCY PROCEDURES
19
If a Gas Line is Damaged
If you suspect a gas line has been damaged, take the following actions. The order and degree of action will depend on the situation.
• Immediately shut off engine(s), if this can be done safely and quickly.
• Remove any ignition source(s), if this can be done safely and quickly.
• Warn others that a gas line has been cut and that they should leave the area.
• Leave jobsite as quickly as possible.
• Immediately call your local emergency phone number and utility company.
• If jobsite is along street, stop traffic from driving near jobsite.
• Do not return to jobsite until given permission by emergency personnel and utility company.
If a Fiber Optic Cable is Damaged
Do not look into cut ends of fiber optic or unidentified cable.
Vision damage can occur.
If Machine Catches on Fire
Perform emergency shutdown procedure and then take the following actions. The order and degree of action will depend on the situation.
• Immediately move battery disconnect switch (if equipped) to disconnect position.
• If fire is small and fire extinguisher is available, attempt to extinguish fire.
• If fire cannot be extinguished, leave area as quickly as possible and contact emergency personnel.
1030/1230 - SAFETY
EMERGENCY PROCEDURES
19
If a Gas Line is Damaged
If you suspect a gas line has been damaged, take the following actions. The order and degree of action will depend on the situation.
• Immediately shut off engine(s), if this can be done safely and quickly.
• Remove any ignition source(s), if this can be done safely and quickly.
• Warn others that a gas line has been cut and that they should leave the area.
• Leave jobsite as quickly as possible.
• Immediately call your local emergency phone number and utility company.
• If jobsite is along street, stop traffic from driving near jobsite.
• Do not return to jobsite until given permission by emergency personnel and utility company.
If a Fiber Optic Cable is Damaged
Do not look into cut ends of fiber optic or unidentified cable.
Vision damage can occur.
If Machine Catches on Fire
Perform emergency shutdown procedure and then take the following actions. The order and degree of action will depend on the situation.
• Immediately move battery disconnect switch (if equipped) to disconnect position.
• If fire is small and fire extinguisher is available, attempt to extinguish fire.
• If fire cannot be extinguished, leave area as quickly as possible and contact emergency personnel.
20
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
JOBSITE CLASSIFICATION
Inspecting Jobsite
• Follow U.S. Department of Labor regulations on excavating and trenching (Part 1926, Subpart P) and other similar regulations.
• Contact One-Call (888-258-0808) and any utility companies which do not subscribe to One-Call.
• Inspect jobsite and perimeter for evidence of underground hazards, such as:
– “Buried utility” notices
– Utility facilities without overhead lines
– Gas or water meters
– Junction boxes
– Drop boxes
– Light poles
– Manhole covers
– Sunken ground
• Have an experienced locating equipment operator sweep area within 20’ (6 m) to each side of trench path. Verify previously marked line and cable locations.
• Mark location of all buried utilities and obstructions.
• Classify jobsite.
20
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
JOBSITE CLASSIFICATION
Inspecting Jobsite
• Follow U.S. Department of Labor regulations on excavating and trenching (Part 1926, Subpart P) and other similar regulations.
• Contact One-Call (888-258-0808) and any utility companies which do not subscribe to One-Call.
• Inspect jobsite and perimeter for evidence of underground hazards, such as:
– “Buried utility” notices
– Utility facilities without overhead lines
– Gas or water meters
– Junction boxes
– Drop boxes
– Light poles
– Manhole covers
– Sunken ground
• Have an experienced locating equipment operator sweep area within 20’ (6 m) to each side of trench path. Verify previously marked line and cable locations.
• Mark location of all buried utilities and obstructions.
• Classify jobsite.
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
21
Selecting a Classification
Jobsites are classified according to underground hazards present.
If working . . .
within 10’ (3 m) of a buried electric line within 10’ (3 m) of a natural gas line in sand, granite, or concrete which is capable of producing crystalline silica (quartz) dust within 10’ (3 m) of any other hazard
then classify jobsite as . . .
electric natural gas crystalline silica (quartz) dust other
NOTICE: If you have any doubt about jobsite classification, or if jobsite might contain unmarked hazards, take steps outlined previously to identify hazards and classify jobsite before working.
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
21
Selecting a Classification
Jobsites are classified according to underground hazards present.
If working . . .
within 10’ (3 m) of a buried electric line within 10’ (3 m) of a natural gas line in sand, granite, or concrete which is capable of producing crystalline silica (quartz) dust within 10’ (3 m) of any other hazard
then classify jobsite as . . .
electric natural gas crystalline silica (quartz) dust other
NOTICE: If you have any doubt about jobsite classification, or if jobsite might contain unmarked hazards, take steps outlined previously to identify hazards and classify jobsite before working.
22
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
Applying Precautions
Once classified, precautions appropriate for jobsite must be taken.
Electric Jobsite Precautions
Use one or both of these methods.
• Expose line by careful hand digging or soft excavation.
• Have service shut down while work is in progress. Have electric company test lines before returning them to service.
Natural Gas Jobsite Precautions
In addition to positioning equipment upwind from gas lines, use one or both of these methods.
• Expose lines by careful hand digging or soft excavation.
• Have gas shut off while work is in progress. Have gas company test lines before returning them to service.
22
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
Applying Precautions
Once classified, precautions appropriate for jobsite must be taken.
Electric Jobsite Precautions
Use one or both of these methods.
• Expose line by careful hand digging or soft excavation.
• Have service shut down while work is in progress. Have electric company test lines before returning them to service.
Natural Gas Jobsite Precautions
In addition to positioning equipment upwind from gas lines, use one or both of these methods.
• Expose lines by careful hand digging or soft excavation.
• Have gas shut off while work is in progress. Have gas company test lines before returning them to service.
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
23
Crystalline Silica (Quartz) Dust Precautions
Follow OSHA or other guidelines for exposure to crystalline silica when trenching, sawing or drilling through material that might produce dust containing crystalline silica (quartz).
Other Jobsite Precautions
You may need to use different methods to safely avoid other underground hazards. Talk with those knowledgeable about hazards present at each site to determine which precautions should be taken or if job should be attempted.
1030/1230 - SAFETY
JOBSITE CLASSIFICATION
23
Crystalline Silica (Quartz) Dust Precautions
Follow OSHA or other guidelines for exposure to crystalline silica when trenching, sawing or drilling through material that might produce dust containing crystalline silica (quartz).
Other Jobsite Precautions
You may need to use different methods to safely avoid other underground hazards. Talk with those knowledgeable about hazards present at each site to determine which precautions should be taken or if job should be attempted.
24
1030/1230 - SAFETY
SAFETY ALERT CLASSIFICATIONS
SAFETY ALERT CLASSIFICATIONS
These classifications and the icons defined on the following pages work together to alert you to situations which could be harmful to you, jobsite bystanders or your equipment. When you see these words and icons in the book or on the machine, carefully read and follow all instructions. YOUR SAFETY IS AT
STAKE.
Watch for the three safety alert levels: DANGER, WARNING and
CAUTION. Learn what each level means.
indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Watch for two other words: NOTICE and IMPORTANT.
NOTICE can keep you from doing something that might damage the machine or someone's property. It can also alert you against unsafe practices.
IMPORTANT can help you do a better job or make your job easier in some way.
24
1030/1230 - SAFETY
SAFETY ALERT CLASSIFICATIONS
SAFETY ALERT CLASSIFICATIONS
These classifications and the icons defined on the following pages work together to alert you to situations which could be harmful to you, jobsite bystanders or your equipment. When you see these words and icons in the book or on the machine, carefully read and follow all instructions. YOUR SAFETY IS AT
STAKE.
Watch for the three safety alert levels: DANGER, WARNING and
CAUTION. Learn what each level means.
indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Watch for two other words: NOTICE and IMPORTANT.
NOTICE can keep you from doing something that might damage the machine or someone's property. It can also alert you against unsafe practices.
IMPORTANT can help you do a better job or make your job easier in some way.
1030/1230 - SAFETY
SAFETY ALERTS
SAFETY ALERTS
Moving digging teeth will kill you or cut off arm or leg. Stay away.
25
Turning shaft will kill you or crush arm or leg. Stay away.
Electric shock. Contacting electric lines will cause death or serious injury. Know location of lines and stay away.
Deadly gases. Lack of oxygen or presence of gas will cause sickness or death.
Provide ventilation.
1030/1230 - SAFETY
SAFETY ALERTS
SAFETY ALERTS
Moving digging teeth will kill you or cut off arm or leg. Stay away.
25
Turning shaft will kill you or crush arm or leg. Stay away.
Electric shock. Contacting electric lines will cause death or serious injury. Know location of lines and stay away.
Deadly gases. Lack of oxygen or presence of gas will cause sickness or death.
Provide ventilation.
26
1030/1230 - SAFETY
SAFETY ALERTS
Jobsite hazards could cause death or serious injury.
Use correct equipment and work methods. Use and maintain proper safety equipment.
Crushing weight could cause death or serious injury.
Use proper procedures and equipment or stay away.
Moving parts could cut off hand or foot. Stay away.
Fall possible. Riders can fall from machine and be injured or killed. Only operator is allowed on machine.
Rollover possible. If machine rolls over, you could be thrown from seat and killed or crushed. Wear seat belt.
26
1030/1230 - SAFETY
SAFETY ALERTS
Jobsite hazards could cause death or serious injury.
Use correct equipment and work methods. Use and maintain proper safety equipment.
Crushing weight could cause death or serious injury.
Use proper procedures and equipment or stay away.
Moving parts could cut off hand or foot. Stay away.
Fall possible. Riders can fall from machine and be injured or killed. Only operator is allowed on machine.
Rollover possible. If machine rolls over, you could be thrown from seat and killed or crushed. Wear seat belt.
1030/1230 - SAFETY
SAFETY ALERTS
27
Explosion possible. Serious injury or equipment damage could occur. Follow directions carefully.
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
Looking into fiber optic cable could result in permanent vision damage. Do not look into ends of fiber optic or unidentified cable.
Fluid or air pressure could pierce skin and cause injury or death. Stay away.
Runaway possible. Machine could run over you or others. Learn how to use all controls. Start and operate only from operator’s position.
1030/1230 - SAFETY
SAFETY ALERTS
27
Explosion possible. Serious injury or equipment damage could occur. Follow directions carefully.
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
Looking into fiber optic cable could result in permanent vision damage. Do not look into ends of fiber optic or unidentified cable.
Fluid or air pressure could pierce skin and cause injury or death. Stay away.
Runaway possible. Machine could run over you or others. Learn how to use all controls. Start and operate only from operator’s position.
28
1030/1230 - SAFETY
SAFETY ALERTS
Fire or explosion possible. Fumes could ignite and cause burns. No smoking, no flame, no spark.
Moving traffic - hazardous situation. Death or serious injury could result.
Avoid moving vehicles, wear high visibility clothing, post appropriate warning signs.
Hot pressurized cooling system fluid could cause serious burns. Allow to cool before servicing.
Improper control function could cause death or serious injury. If control does not work as described in instructions, stop machine and have it serviced.
28
1030/1230 - SAFETY
SAFETY ALERTS
Fire or explosion possible. Fumes could ignite and cause burns. No smoking, no flame, no spark.
Moving traffic - hazardous situation. Death or serious injury could result.
Avoid moving vehicles, wear high visibility clothing, post appropriate warning signs.
Hot pressurized cooling system fluid could cause serious burns. Allow to cool before servicing.
Improper control function could cause death or serious injury. If control does not work as described in instructions, stop machine and have it serviced.
1030/1230 - SAFETY
SAFETY ALERTS
Flying objects may cause injury.
Wear hard hat and safety glasses.
29
touch until cool.
Hot parts may cause burns. Do not
Exposure to high noise levels may cause hearing loss. Wear hearing protection.
Fall possible. Slips or trips may result in injury. Keep area clean.
Avoid contact.
Battery acid may cause burns.
Improper handling or use of chemicals may result in illness, injury, or equipment damage. Follow instructions on labels and in material safety data sheets (MSDS).
1030/1230 - SAFETY
SAFETY ALERTS
Flying objects may cause injury.
Wear hard hat and safety glasses.
29
touch until cool.
Hot parts may cause burns. Do not
Exposure to high noise levels may cause hearing loss. Wear hearing protection.
Fall possible. Slips or trips may result in injury. Keep area clean.
Avoid contact.
Battery acid may cause burns.
Improper handling or use of chemicals may result in illness, injury, or equipment damage. Follow instructions on labels and in material safety data sheets (MSDS).
30
1030/1230 - SAFETY
SAFETY ALERTS
30
1030/1230 - SAFETY
SAFETY ALERTS
1030/1230 - TRANSPORTATION
LIFT
31
TRANSPORTATION
LIFT
Lifting Points
Lifting points are identified by lifting decals. Lifting at any other point can be unsafe and can damage machinery.
om1362.pcx
1030/1230 - TRANSPORTATION
LIFT
31
TRANSPORTATION
LIFT
Lifting Points
Lifting points are identified by lifting decals. Lifting at any other point can be unsafe and can damage machinery.
om1362.pcx
32
1030/1230 - TRANSPORTATION
LIFT
Lifting Unit
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
Before lifting, check SPECIFICATIONS. Use a hoist capable of supporting equipment’s size and weight.
Lift trencher by running a sling through the front guide, under lifting hooks, and around back of console tower.
32
1030/1230 - TRANSPORTATION
LIFT
Lifting Unit
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
Before lifting, check SPECIFICATIONS. Use a hoist capable of supporting equipment’s size and weight.
Lift trencher by running a sling through the front guide, under lifting hooks, and around back of console tower.
1030/1230 - TRANSPORTATION
TIEDOWN
TIEDOWN
Tiedown Points
Tiedown points are identified by tiedown decals. Securing unit to truck or trailer at any other points may be unsafe and can damage machinery.
om1363.pcx
Tieing Down Unit
Attach tiedowns at front and rear tiedown points. Make sure tiedowns are tight before transporting unit.
33 1030/1230 - TRANSPORTATION
TIEDOWN
TIEDOWN
Tiedown Points
Tiedown points are identified by tiedown decals. Securing unit to truck or trailer at any other points may be unsafe and can damage machinery.
om1363.pcx
Tieing Down Unit
Attach tiedowns at front and rear tiedown points. Make sure tiedowns are tight before transporting unit.
33
34
HAUL
1030/1230 - TRANSPORTATION
HAUL
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
NOTICES:
• Read trailer operator’s manual, if applicable, before loading or transporting your machine. Incorrectly loaded machine can slip or cause trailer sway.
• Check that loading ramps will support weight (see
SPECIFICATIONS).
• Check payload rating of truck or trailer.
• Park, load, and unload truck or trailer on a level part of the jobsite.
• Check that adequate tiedowns are available.
34
HAUL
1030/1230 - TRANSPORTATION
HAUL
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
NOTICES:
• Read trailer operator’s manual, if applicable, before loading or transporting your machine. Incorrectly loaded machine can slip or cause trailer sway.
• Check that loading ramps will support weight (see
SPECIFICATIONS).
• Check payload rating of truck or trailer.
• Park, load, and unload truck or trailer on a level part of the jobsite.
• Check that adequate tiedowns are available.
1030/1230 - TRANSPORTATION
HAUL
35
Loading
The 1030 and 1230 trenchers can be hauled in the bed of a light truck or by trailer. To load:
1.
Start engine. See OPERATION for start-up procedures.
2.
Raise digging boom, but keep it low.
3.
Move throttle to about 3/4 open.
4.
With bail engaged, move speed/direction control to forward or reverse and drive to loading sight.
To steer, unlock axle, push down on handlebar, and turn machine.
5.
Align trencher with ramps or trailer.
6.
Lock axle.
7.
Drive trencher onto trailer or truck bed until tiedown position is reached.
8.
Move speed/direction control to BAIL RELEASE (neutral) position, and lower digging boom.
9.
Release bail and turn off engine.
10. Securely chain trencher to truck or trailer at tiedown points.
NOTICE: To keep engine from flooding during transport, close both fuel shut-off valves before transporting unit.
1030/1230 - TRANSPORTATION
HAUL
35
Loading
The 1030 and 1230 trenchers can be hauled in the bed of a light truck or by trailer. To load:
1.
Start engine. See OPERATION for start-up procedures.
2.
Raise digging boom, but keep it low.
3.
Move throttle to about 3/4 open.
4.
With bail engaged, move speed/direction control to forward or reverse and drive to loading sight.
To steer, unlock axle, push down on handlebar, and turn machine.
5.
Align trencher with ramps or trailer.
6.
Lock axle.
7.
Drive trencher onto trailer or truck bed until tiedown position is reached.
8.
Move speed/direction control to BAIL RELEASE (neutral) position, and lower digging boom.
9.
Release bail and turn off engine.
10. Securely chain trencher to truck or trailer at tiedown points.
NOTICE: To keep engine from flooding during transport, close both fuel shut-off valves before transporting unit.
36
1030/1230 - TRANSPORTATION
HAUL
Unloading
1.
Remove tiedowns.
2.
Open fuel shut-off valves and start engine.
3.
Move throttle to about 1/4 open.
4.
Ensure that axle is locked and speed/direction control is in the BAIL RELEASE (neutral) position.
5.
Engage bail.
6.
Raise digging boom, but keep it low.
7.
Slowly drive trencher off trailer.
36
1030/1230 - TRANSPORTATION
HAUL
Unloading
1.
Remove tiedowns.
2.
Open fuel shut-off valves and start engine.
3.
Move throttle to about 1/4 open.
4.
Ensure that axle is locked and speed/direction control is in the BAIL RELEASE (neutral) position.
5.
Engage bail.
6.
Raise digging boom, but keep it low.
7.
Slowly drive trencher off trailer.
1030/1230 - TRANSPORTATION
FREEWHEEL
37
FREEWHEEL
If trencher must be moved without engine running, this feature allows the 1030 or 1230 to be wheeled manually.
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
sf1014
1.
Elevate left side of trencher with jackstand or safety blocks.
2.
Remove nut from left wheel hub.
3.
Horizontally align two of the three threaded holes (A) in wheel hub with machine frame, as shown.
4.
Insert bolts (supplied in operator’s manual compartment) into threaded holes and tighten until wheel is released from axle.
5.
Remove key (B) from axle.
6.
Replace wheel and hub, and tighten only enough to keep hub on axle. Overtightening can lock hub to axle.
7.
Wheel trencher to a clear area of the jobsite.
NOTICE: Do not freewheel the threncher more than 100’
(30 m) in this manner. Damage to wheel hub or axle will occur.
1030/1230 - TRANSPORTATION
FREEWHEEL
37
FREEWHEEL
If trencher must be moved without engine running, this feature allows the 1030 or 1230 to be wheeled manually.
Crushing weight could cause death or serious injury. Use proper procedures and equipment or stay away.
sf1014
1.
Elevate left side of trencher with jackstand or safety blocks.
2.
Remove nut from left wheel hub.
3.
Horizontally align two of the three threaded holes (A) in wheel hub with machine frame, as shown.
4.
Insert bolts (supplied in operator’s manual compartment) into threaded holes and tighten until wheel is released from axle.
5.
Remove key (B) from axle.
6.
Replace wheel and hub, and tighten only enough to keep hub on axle. Overtightening can lock hub to axle.
7.
Wheel trencher to a clear area of the jobsite.
NOTICE: Do not freewheel the threncher more than 100’
(30 m) in this manner. Damage to wheel hub or axle will occur.
38
1030/1230 - TRANSPORTATION
TOW
TOW
Under normal conditions, unit should not be towed. If unit becomes disabled and towing is necessary:
• tow for short distances at less than 1 mph (1.6 km/h)
• do not tow for more than 100’ (30 m)
• use no more than 1,300 lb (5 800 N) of towing force
To tow:
1.
Follow “Freewheel” instructions to enable unit to be towed.
2.
Attach tow line to all available tiedown points facing towing vehicle.
38
1030/1230 - TRANSPORTATION
TOW
TOW
Under normal conditions, unit should not be towed. If unit becomes disabled and towing is necessary:
• tow for short distances at less than 1 mph (1.6 km/h)
• do not tow for more than 100’ (30 m)
• use no more than 1,300 lb (5 800 N) of towing force
To tow:
1.
Follow “Freewheel” instructions to enable unit to be towed.
2.
Attach tow line to all available tiedown points facing towing vehicle.
1030/1230 - OPERATION
DAILY INSPECTION
39
OPERATION
DAILY INSPECTION
For safe and efficient use of your machine, do the following before each day’s work.
• Check general appearance of tractor and digging attachment.
Look for loose, worn, or damaged parts and fluid leaks.
• Check condition of digging chain, teeth, air filter, and optional remote air cleaner.
• Check fuel lines and hydraulic lines and fittings for signs of leakage, wear, or other damage.
• Check tire pressure.
• Check hydraulic and engine oil levels.
• Check fuel level.
• Check that all signs, guards, and shields are in place and readable.
Service machine according to schedules in LUBRICATION AND
MAINTENANCE, and in engine manufacturer’s guide.
1030/1230 - OPERATION
DAILY INSPECTION
39
OPERATION
DAILY INSPECTION
For safe and efficient use of your machine, do the following before each day’s work.
• Check general appearance of tractor and digging attachment.
Look for loose, worn, or damaged parts and fluid leaks.
• Check condition of digging chain, teeth, air filter, and optional remote air cleaner.
• Check fuel lines and hydraulic lines and fittings for signs of leakage, wear, or other damage.
• Check tire pressure.
• Check hydraulic and engine oil levels.
• Check fuel level.
• Check that all signs, guards, and shields are in place and readable.
Service machine according to schedules in LUBRICATION AND
MAINTENANCE, and in engine manufacturer’s guide.
40
1030/1230 - OPERATION
STARTUP
STARTUP
Before operating trencher, read engine manufacturer’s starting and operating instructions. Follow instructions for new engine break-in.
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
EMERGENCY SHUTDOWN: Turn power switch off.
40
1030/1230 - OPERATION
STARTUP
STARTUP
Before operating trencher, read engine manufacturer’s starting and operating instructions. Follow instructions for new engine break-in.
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
EMERGENCY SHUTDOWN: Turn power switch off.
1030/1230 - OPERATION
STARTUP
41
1.
Check that bail is up and fuel shut-off valves are open.
2.
If necessary, choke cold engine.
3.
Move throttle to 1/4 open.
4.
Turn power switch on.
5.
Pull rope start.
IMPORTANT: If engine does not start after three pulls, turn power switch off and check for fuel blockage or electrical system problems.
Improper control function could cause death or serious injury. If control does not work as described in instructions, stop machine and have it serviced.
NOTICES:
• If interlock system does not work, contact your Ditch Witch dealer. Improper repair might allow machine to start or operate with controls in gear.
• Do not wire or tape bail to handlebar or defeat interlock system in any manner. Machine will not start, and digging chain control will be stuck in gear.
6.
Run engine at half throttle or less for five minutes before operating trencher.
During warmup, check that all controls work properly.
EMERGENCY SHUTDOWN: Turn power switch off.
1030/1230 - OPERATION
STARTUP
41
1.
Check that bail is up and fuel shut-off valves are open.
2.
If necessary, choke cold engine.
3.
Move throttle to 1/4 open.
4.
Turn power switch on.
5.
Pull rope start.
IMPORTANT: If engine does not start after three pulls, turn power switch off and check for fuel blockage or electrical system problems.
Improper control function could cause death or serious injury. If control does not work as described in instructions, stop machine and have it serviced.
NOTICES:
• If interlock system does not work, contact your Ditch Witch dealer. Improper repair might allow machine to start or operate with controls in gear.
• Do not wire or tape bail to handlebar or defeat interlock system in any manner. Machine will not start, and digging chain control will be stuck in gear.
6.
Run engine at half throttle or less for five minutes before operating trencher.
During warmup, check that all controls work properly.
EMERGENCY SHUTDOWN: Turn power switch off.
42
1030/1230 - OPERATION
DRIVING
DRIVING
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
NOTICE: Keep attachment low when operating on a slope. Drive slowly and cautiously at all times.
1.
Ensure that speed/direction control is in the BAIL RELEASE
(neutral) position.
2.
Move bail down into handlebar.
3.
Raise digging boom.
4.
Lock axle to drive straight, or unlock axle to allow steering.
5.
Move throttle to 3/4 open.
6.
Move speed/direciton control to forward or reverse.
IMPORTANT: Bail must be down in order for unit to move.
7.
To steer, ensure axle is unlocked, push down on handlebar, and turn machine.
42
1030/1230 - OPERATION
DRIVING
DRIVING
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
NOTICE: Keep attachment low when operating on a slope. Drive slowly and cautiously at all times.
1.
Ensure that speed/direction control is in the BAIL RELEASE
(neutral) position.
2.
Move bail down into handlebar.
3.
Raise digging boom.
4.
Lock axle to drive straight, or unlock axle to allow steering.
5.
Move throttle to 3/4 open.
6.
Move speed/direciton control to forward or reverse.
IMPORTANT: Bail must be down in order for unit to move.
7.
To steer, ensure axle is unlocked, push down on handlebar, and turn machine.
1030/1230 - OPERATION
TRENCHING
TRENCHING
43
Jobsite hazards could cause death or serious injury.
Use correct equipment and work methods. Use and maintain proper safety equipment.
NOTICE: Know and comply with regulations covering One-Call service and utility notification before digging.
Jobsite hazards could cause death or serious injury. Use correct equipment and work methods. Use and maintain proper safety equipment.
NOTICE: Cutting or drilling concrete containing sand or rock containing quartz may result in exposure to silica dust. Use respirator, water spray or other means to control dust. Silica dust can cause lung disease and is known to the State of California to cause cancer.
1030/1230 - OPERATION
TRENCHING
TRENCHING
43
Jobsite hazards could cause death or serious injury.
Use correct equipment and work methods. Use and maintain proper safety equipment.
NOTICE: Know and comply with regulations covering One-Call service and utility notification before digging.
Jobsite hazards could cause death or serious injury. Use correct equipment and work methods. Use and maintain proper safety equipment.
NOTICE: Cutting or drilling concrete containing sand or rock containing quartz may result in exposure to silica dust. Use respirator, water spray or other means to control dust. Silica dust can cause lung disease and is known to the State of California to cause cancer.
44
1030/1230 - OPERATION
TRENCHING
1.
Drive trencher to starting point. Move in line with planned trench.
2.
For a straighter trench, lock axle.
3.
Move throttle to half open.
4.
Ensure that speed/direction control and digging chain control are in neutral.
5.
Lower digging boom to just above ground.
Moving digging teeth will cause death or serious injury. Stay away.
NOTICE: Keep everyone at lease 6’ (2 m) from machine, digging boom, and its range of movement.
6.
Engage digging chain control. DIGGING CHAIN WILL
MOVE.
EMERGENCY STOP: Release bail.
44
1030/1230 - OPERATION
TRENCHING
1.
Drive trencher to starting point. Move in line with planned trench.
2.
For a straighter trench, lock axle.
3.
Move throttle to half open.
4.
Ensure that speed/direction control and digging chain control are in neutral.
5.
Lower digging boom to just above ground.
Moving digging teeth will cause death or serious injury. Stay away.
NOTICE: Keep everyone at lease 6’ (2 m) from machine, digging boom, and its range of movement.
6.
Engage digging chain control. DIGGING CHAIN WILL
MOVE.
EMERGENCY STOP: Release bail.
1030/1230 - OPERATION
TRENCHING
7.
Slowly lower digging boom to desired trench depth.
45
Incorrect procedures can result in death, injury, or property damage. Learn to use equipment correctly.
NOTICES:
• Machine may move when chain starts to dig. Allow 3’ (1 m) between end of chain and obstacle.
• Digging chain on top side of boom can catch on root or rock, forcing handlebar down suddenly. Stand back from console and hold handlebar loosley.
8.
When desired trench depth is reached, move throttle to full open.
9.
Move speed/direction control to reverse. Trencher will move toward you.
Trenching movement is toward you.
1030/1230 - OPERATION
TRENCHING
7.
Slowly lower digging boom to desired trench depth.
45
Incorrect procedures can result in death, injury, or property damage. Learn to use equipment correctly.
NOTICES:
• Machine may move when chain starts to dig. Allow 3’ (1 m) between end of chain and obstacle.
• Digging chain on top side of boom can catch on root or rock, forcing handlebar down suddenly. Stand back from console and hold handlebar loosley.
8.
When desired trench depth is reached, move throttle to full open.
9.
Move speed/direction control to reverse. Trencher will move toward you.
Trenching movement is toward you.
om0045c om0045c
46
1030/1230 - OPERATION
TRENCHING
10. When trench is complete, move speed direction control to neutral.
11. Move throttle to half open.
12. Raise digging boom to top of trench.
13. Release bail to stop digging chain.
14. Engage bail and raise digging boom completely.
15. Drive trencher away from trench.
16. Let machine idle for three minutes to cool engine.
17. Turn power switch off.
46
1030/1230 - OPERATION
TRENCHING
10. When trench is complete, move speed direction control to neutral.
11. Move throttle to half open.
12. Raise digging boom to top of trench.
13. Release bail to stop digging chain.
14. Engage bail and raise digging boom completely.
15. Drive trencher away from trench.
16. Let machine idle for three minutes to cool engine.
17. Turn power switch off.
1030/1230 - LUBRICATION AND MAINTENANCE
TRENCHING
47
LUBRICATION AND
MAINTENANCE
Proper lubrication and maintenance protects Ditch Witch equipment from damage and failure. In extreme conditions, lubricate more frequently.
Use only recommended lubricants. Fill to capacities listed in
SPECIFICATIONS.
Recommended Lubricants
GEO
AGMA-7
MPG
THF
Gasoline engine oil (see chart for appropriate SAE viscosity rating) meeting API engine service classification SD
Worm gear lubricant matching American Gear Manufacturer’s Association Compound #7
Multipurpose grease
Tractor hydraulic fluid, similar to Phillips 66 HG, Mobilfluid 423, Chevron Tractor Hydraulic
Fluid, Texaco TDH Oil, or equivalent
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
NOTICES:
• Unless otherwise instructed, all service should be performed with engine off.
• Refer to engine manufacturer’s manual for engine maintenance instructions.
• Before servicing equipment, lower digging boom to ground.
1030/1230 - LUBRICATION AND MAINTENANCE
TRENCHING
47
LUBRICATION AND
MAINTENANCE
Proper lubrication and maintenance protects Ditch Witch equipment from damage and failure. In extreme conditions, lubricate more frequently.
Use only recommended lubricants. Fill to capacities listed in
SPECIFICATIONS.
Recommended Lubricants
GEO
AGMA-7
MPG
THF
Gasoline engine oil (see chart for appropriate SAE viscosity rating) meeting API engine service classification SD
Worm gear lubricant matching American Gear Manufacturer’s Association Compound #7
Multipurpose grease
Tractor hydraulic fluid, similar to Phillips 66 HG, Mobilfluid 423, Chevron Tractor Hydraulic
Fluid, Texaco TDH Oil, or equivalent
Incorrect procedures could result in death, injury, or property damage. Learn to use equipment correctly.
NOTICES:
• Unless otherwise instructed, all service should be performed with engine off.
• Refer to engine manufacturer’s manual for engine maintenance instructions.
• Before servicing equipment, lower digging boom to ground.
48
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION OVERVIEW
LUBRICATION OVERVIEW
48
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION OVERVIEW
LUBRICATION OVERVIEW
(GEO) Gasoline engine oil
AGMA-7
(THF) Tractor hydraulic fluid
(MPG) Multipurpose grease
Check level Filter
Pivot gearbox on opposite side of machine not shown. Check oil every 50 hours. Change gearbox oil every 1000 hours with
THF
(GEO) Gasoline engine oil
AGMA-7
(THF) Tractor hydraulic fluid
(MPG) Multipurpose grease
Check level Filter
Pivot gearbox on opposite side of machine not shown. Check oil every 50 hours. Change gearbox oil every 1000 hours with
THF
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
LUBRICATION SCHEDULE
Interval
Each use
10 hours
25 hours
50 hours
100 hours
250 hours
500 hours
1000 hours
Task
Check engine oil
Check hydraulic oil
Lube attachment pivot
Lube pivot stub
Lube trail wheel
Lube axle lock
Check pivot gearbox oil
Check worm drive oil
Lube digging boom adjustment screw
Lube greaseable digging boom stub
Change engine oil
Change hydraulic filter
Change hydraulic oil
Change worm drive oil
Change pivot gearbox oil
51
51
54
53
54
55
55
50
54
52
52
53
Page
50
51
52
49 1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
LUBRICATION SCHEDULE
Interval
Each use
10 hours
25 hours
50 hours
100 hours
250 hours
500 hours
1000 hours
Task
Check engine oil
Check hydraulic oil
Lube attachment pivot
Lube pivot stub
Lube trail wheel
Lube axle lock
Check pivot gearbox oil
Check worm drive oil
Lube digging boom adjustment screw
Lube greaseable digging boom stub
Change engine oil
Change hydraulic filter
Change hydraulic oil
Change worm drive oil
Change pivot gearbox oil
51
51
54
53
54
55
55
50
54
52
52
53
Page
50
51
52
49
50
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Engine Oil
Check
Check engine oil at dipstick (A) before each operation. Add GEO at fill neck (A) as necessary to keep oil level at highest line on dipstick.
Change
• Change oil every 100 hours with GEO.
• Drain crankcase (B) while oil is still warm.
• Refill at fill neck with 2.3 pt
(1.1 L) of GEO.
50
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Engine Oil
Check
Check engine oil at dipstick (A) before each operation. Add GEO at fill neck (A) as necessary to keep oil level at highest line on dipstick.
Change
• Change oil every 100 hours with GEO.
• Drain crankcase (B) while oil is still warm.
• Refill at fill neck with 2.3 pt
(1.1 L) of GEO.
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Hydraulic Oil and Filter
Check
With digging boom fully raised, check hydraulic oil at dipstick (A) before each operation. Add THF at fill neck (A) as necessary to keep oil level at highest line on dipstick.
Clean dust from cap by blowing with low pressure air.
Change
Change hydraulic filter (B) every
250 hours.
Drain hydraulic oil at drain (C), change filter, and refill at fill neck with THF every 500 hours.
51 1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Hydraulic Oil and Filter
Check
With digging boom fully raised, check hydraulic oil at dipstick (A) before each operation. Add THF at fill neck (A) as necessary to keep oil level at highest line on dipstick.
Clean dust from cap by blowing with low pressure air.
Change
Change hydraulic filter (B) every
250 hours.
Drain hydraulic oil at drain (C), change filter, and refill at fill neck with THF every 500 hours.
51
52
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Tires
Lube trail wheel (A) every 25 hours with MPG.
Pivot
Lube Pivot (B) every 10 hours with
MPG.
Axle Lock
Lube axle lock every 25 hours with
MPG.
52
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Tires
Lube trail wheel (A) every 25 hours with MPG.
Pivot
Lube Pivot (B) every 10 hours with
MPG.
Axle Lock
Lube axle lock every 25 hours with
MPG.
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Pivot Gearbox
Check
Check gearbox oil every 50 hours at fill plug (A). Refill with THF as necessary to keep oil level with fill plug.
Change
Change gearbox oil every 1000 hours.
• Remove both plugs and drain oil.
• Replace bottom plug (B).
• Fill with THF to fill plug, approximately 2 pt (.95 L).
• Replace fill plug.
53 1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Pivot Gearbox
Check
Check gearbox oil every 50 hours at fill plug (A). Refill with THF as necessary to keep oil level with fill plug.
Change
Change gearbox oil every 1000 hours.
• Remove both plugs and drain oil.
• Replace bottom plug (B).
• Fill with THF to fill plug, approximately 2 pt (.95 L).
• Replace fill plug.
53
54
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Worm Drive
Check
Check worm drive oil every 50 hours at fill plug (A). Refill with
AGMA-7 as necessary to keep oil level with fill plug.
Change
Change worm drive oil every 500 hours.
• Empty worm drive at drain (B).
• Replace drain plug.
• Fill with AGMA-7 to fill plug, approximately 3.25 pt (1.5 L).
NOTICE: Do not use a substitute lubricant. Worm drive failure could occur.
om0049c om1571
54
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Worm Drive
Check
Check worm drive oil every 50 hours at fill plug (A). Refill with
AGMA-7 as necessary to keep oil level with fill plug.
Change
Change worm drive oil every 500 hours.
• Empty worm drive at drain (B).
• Replace drain plug.
• Fill with AGMA-7 to fill plug, approximately 3.25 pt (1.5 L).
NOTICE: Do not use a substitute lubricant. Worm drive failure could occur.
om0049c om1571
1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Digging Boom
Boom with Adjustment Screw
Lube adjustment screw (A) every
50 hours with MPG.
Lube pivot stub (B) every 10 hours with MPG.
om0056c
Greaseable Boom
Lube boom stub every 50 hours with MPG.
55 1030/1230 - LUBRICATION AND MAINTENANCE
LUBRICATION SCHEDULE
Digging Boom
Boom with Adjustment Screw
Lube adjustment screw (A) every
50 hours with MPG.
Lube pivot stub (B) every 10 hours with MPG.
om0056c
Greaseable Boom
Lube boom stub every 50 hours with MPG.
55
56
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
Interval
Each use
100 hours
As needed
Trail Wheel
Task
Check tire pressure
Check lug nut torque
Change air filter paper element
Change remote air cleaner paper element
Adjust digging chain tension
Adjust drive belt tension
57
57
59
Page
56
56
56
Tire Pressure
Check trail wheel tire pressure daily. Maintain pressure under 32 psi (221 kPa).
Lug Nut Torque
Check lug nut torque daile. Tighten to 85 ft•lb (115 N•m).
Air Filter
Change foam air filter element every 100 hours. Do not allow dirt to fall into carburetor.
56
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE
Interval
Each use
100 hours
As needed
Trail Wheel
Task
Check tire pressure
Check lug nut torque
Change air filter paper element
Change remote air cleaner paper element
Adjust digging chain tension
Adjust drive belt tension
57
57
59
Page
56
56
56
Tire Pressure
Check trail wheel tire pressure daily. Maintain pressure under 32 psi (221 kPa).
Lug Nut Torque
Check lug nut torque daile. Tighten to 85 ft•lb (115 N•m).
Air Filter
Change foam air filter element every 100 hours. Do not allow dirt to fall into carburetor.
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Remote Air Cleaner
Change optional air cleaner paper element as needed.
• Remove air cleaner cover.
• Remove paper element and replace.
NOTICE: Use of this option does not eliminate the need for proper maintenance of standard air filter.
Digging Chain Tension
Check digging chain regularly and adjust as needed.
Adjustment Screw
Digging chain is properly tensioned when chain can be moved
.5” (13 mm) up or down. To adjust digging chain tension:
• Loosen four clamp bolts (B) so that boom slides freely.
• Lossen jam nut on adjustment screw (A).
• Turn adjustment screw clockwise to tighten digging chain or counterclockwise to loosen digging chain.
• When proper tension is reached, tighten jam nut and torque clamp bolts to 75 ft•lb
(102 N•m).
om1565
57 1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Remote Air Cleaner
Change optional air cleaner paper element as needed.
• Remove air cleaner cover.
• Remove paper element and replace.
NOTICE: Use of this option does not eliminate the need for proper maintenance of standard air filter.
Digging Chain Tension
Check digging chain regularly and adjust as needed.
Adjustment Screw
Digging chain is properly tensioned when chain can be moved
.5” (13 mm) up or down. To adjust digging chain tension:
• Loosen four clamp bolts (B) so that boom slides freely.
• Lossen jam nut on adjustment screw (A).
• Turn adjustment screw clockwise to tighten digging chain or counterclockwise to loosen digging chain.
• When proper tension is reached, tighten jam nut and torque clamp bolts to 75 ft•lb
(102 N•m).
om1565
57
58
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Grease Cylinder:
To tighten digging chain, pump
MPG into cylinder at check valve zerk.
NOTICE: Do not overtighten chain. Overtightening will cause chain stretch, loss of machine performance, and possible premature chain failure.
To loosen digging chain, stand on opposite side of boom and unscrew check valve zerk to release grease.
Fluid pressure could pierce skin and cause injury or death. Stay away.
NOTICE: Service digging boom grease cylinder only while standing on opposite side of boom. Wear gloves and safety glasses and cover fitting with cloth when relieving pressure in cylinder.
58
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Grease Cylinder:
To tighten digging chain, pump
MPG into cylinder at check valve zerk.
NOTICE: Do not overtighten chain. Overtightening will cause chain stretch, loss of machine performance, and possible premature chain failure.
To loosen digging chain, stand on opposite side of boom and unscrew check valve zerk to release grease.
Fluid pressure could pierce skin and cause injury or death. Stay away.
NOTICE: Service digging boom grease cylinder only while standing on opposite side of boom. Wear gloves and safety glasses and cover fitting with cloth when relieving pressure in cylinder.
1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Drive Belts
Check drive belts regularly and adjust tension as needed.
• Turn engine off.
• Move bail down into handlebar and clamp in place.
• Engage digging chain control until locked in place.
• Tighten or loosen both digging belt adjustment nut (1) and pump belt adjustment nut (2) until springs (A and B) are each 1.8” (48 mm) long.
See repair guide for more information.
1 rg0020c.eps
A
2 rg0012c.eps
B
59 1030/1230 - LUBRICATION AND MAINTENANCE
MAINTENANCE SCHEDULE
Drive Belts
Check drive belts regularly and adjust tension as needed.
• Turn engine off.
• Move bail down into handlebar and clamp in place.
• Engage digging chain control until locked in place.
• Tighten or loosen both digging belt adjustment nut (1) and pump belt adjustment nut (2) until springs (A and B) are each 1.8” (48 mm) long.
See repair guide for more information.
1 rg0020c.eps
A
2 rg0012c.eps
B
59
60
1030/1230 - LUBRICATION AND MAINTENANCE 60
1030/1230 - LUBRICATION AND MAINTENANCE
1030/1230 - SPECIFICATIONS
1030
61
SPECIFICATIONS
1030
1030/1230 - SPECIFICATIONS
1030
61
SPECIFICATIONS
1030
om0050c.eps
W
4
A
3
L
4
C
1
F
L
2
W
2
H
2
B
C
DIMENSIONS
A Trench depth, maximum
Trench width
Boom travel down
Boom travel up
Headshaft height--digging chain
Length
Width
Height
Tread
Angle of departure
Wheelbase
U.S.
30 in
4.3 - 6 in
60°
47°
8.60 in
88 in
32 in
47 in
26 in
65°
32 in
METRIC
760 mm
110-150 mm
60°
47°
220 mm
2.2 m
810 mm
1.2 m
660 mm
65°
810 mm om0050c.eps
W
4
A
3
L
4
C
1
F
L
2
W
2
H
2
B
C
DIMENSIONS
A Trench depth, maximum
Trench width
Boom travel down
Boom travel up
Headshaft height--digging chain
Length
Width
Height
Tread
Angle of departure
Wheelbase
U.S.
30 in
4.3 - 6 in
60°
47°
8.60 in
88 in
32 in
47 in
26 in
65°
32 in
METRIC
760 mm
110-150 mm
60°
47°
220 mm
2.2 m
810 mm
1.2 m
660 mm
65°
810 mm
62
1030/1230 - SPECIFICATIONS
1030
DIMENSIONS
E
1
Centerline trench to outside edge of machine, left
E
2
Centerline trench to outside edge of machine, right
U.S.
15 in
17 in
METRIC
381 mm
432 mm
N Spoil discharge reach
Angle of approach
10.6 in
35°
270 mm
35°
A
2
Dimensions based on 16x6.50x8 tires and 24” (610-mm) boom in transport position
GENERAL
Ditch Witch model 1030, self-propelled, pedestrian, manually steered, twowheel drive rigid frame, chain type trencher
OPERATIONAL
Vehicle speeds
U.S.
METRIC
Maximum transit forward
Maximim transit reverse
Digging chain speed
Spoils handling (single, open-end auger)
155 fpm
155 fpm
276 fpm
47 m/min
47 m/min
84 m/min
Outer diameter
Inner diameter
Length
Operating weight [with 33,000-lb (14 969-kg) test, two-pitch digging chain]
POWER
Engine: Honda GX340
Fuel: gasoline
Cooling medium: air
Number of cylinders: 1
Displacement
12 in
4 in
9 in
900 lb
U.S.
305 mm
102 mm
229 mm
408 kg
METRIC
Bore
Stroke
Gross power @ 3600 rpm
20.6 in
3
3.22 in
2.52 in
11 hp
337 cm
3
82 mm
64 mm
8.2 kW
62
1030/1230 - SPECIFICATIONS
1030
DIMENSIONS
E
1
Centerline trench to outside edge of machine, left
E
2
Centerline trench to outside edge of machine, right
U.S.
15 in
17 in
METRIC
381 mm
432 mm
N Spoil discharge reach
Angle of approach
10.6 in
35°
270 mm
35°
A
2
Dimensions based on 16x6.50x8 tires and 24” (610-mm) boom in transport position
GENERAL
Ditch Witch model 1030, self-propelled, pedestrian, manually steered, twowheel drive rigid frame, chain type trencher
OPERATIONAL
Vehicle speeds
U.S.
METRIC
Maximum transit forward
Maximim transit reverse
Digging chain speed
Spoils handling (single, open-end auger)
155 fpm
155 fpm
276 fpm
47 m/min
47 m/min
84 m/min
Outer diameter
Inner diameter
Length
Operating weight [with 33,000-lb (14 969-kg) test, two-pitch digging chain]
POWER
Engine: Honda GX340
Fuel: gasoline
Cooling medium: air
Number of cylinders: 1
Displacement
12 in
4 in
9 in
900 lb
U.S.
305 mm
102 mm
229 mm
408 kg
METRIC
Bore
Stroke
Gross power @ 3600 rpm
20.6 in
3
3.22 in
2.52 in
11 hp
337 cm
3
82 mm
64 mm
8.2 kW
1030/1230 - SPECIFICATIONS
1030
POWER
Maximum governed speed installed (no load)
Flywheel power @ 3200 rpm (full load)
Fuel consumption @3600 rpm
Maximum tilt angle
Fuel tank capacity
Engine oil capacity
POWER TRAIN
U.S.
3400 rpm
10.2 hp
.89 gph
20°
1.7 gal
2.3 pt
METRIC
3400 rpm
7.5 kW
3.4 L/h
20°
6.5 L
1.1 L
Ground drive transmission
Ground drive: hydrostatic, infinitely variable from zero to maximum, gearbox to axle, speed and direction controlled with single lever
Pump drive clutch: mechanical, hand-operated, spring-loaded, with tension roller for belt drive
Digging chain clutch: mechanical, hand-operated,spring-loaded with tension roller for belt drive
Tires
Drive, standard: 16x6.50x8
Drive, optional: 18x8.50x8
Trail: 13x5.00x6
Trencher drive: mechanical, belt drive to reduction drive, headshaft
Belt: “power band,” two-groove
Digging chain: 33,000 lb (16 969 kg) test
Chain drive sprocket: forged and tempered
Digging teeth: bolt-on cup teeth with hard-surfaced edge of tungsten carbide
Spoils handling drive: mechanical, attached to and rotates with headshaft
NOISE LEVELS
Operator 88dBA sound pressure per ISO 6394.
Exterior 101 dBA sound power per ISO 6393.
VIBRATION LEVELS
Vibration at the operator’s hand during normal operation is 6.1 m/s
2
63 1030/1230 - SPECIFICATIONS
1030
POWER
Maximum governed speed installed (no load)
Flywheel power @ 3200 rpm (full load)
Fuel consumption @3600 rpm
Maximum tilt angle
Fuel tank capacity
Engine oil capacity
POWER TRAIN
U.S.
3400 rpm
10.2 hp
.89 gph
20°
1.7 gal
2.3 pt
METRIC
3400 rpm
7.5 kW
3.4 L/h
20°
6.5 L
1.1 L
Ground drive transmission
Ground drive: hydrostatic, infinitely variable from zero to maximum, gearbox to axle, speed and direction controlled with single lever
Pump drive clutch: mechanical, hand-operated, spring-loaded, with tension roller for belt drive
Digging chain clutch: mechanical, hand-operated,spring-loaded with tension roller for belt drive
Tires
Drive, standard: 16x6.50x8
Drive, optional: 18x8.50x8
Trail: 13x5.00x6
Trencher drive: mechanical, belt drive to reduction drive, headshaft
Belt: “power band,” two-groove
Digging chain: 33,000 lb (16 969 kg) test
Chain drive sprocket: forged and tempered
Digging teeth: bolt-on cup teeth with hard-surfaced edge of tungsten carbide
Spoils handling drive: mechanical, attached to and rotates with headshaft
NOISE LEVELS
Operator 88dBA sound pressure per ISO 6394.
Exterior 101 dBA sound power per ISO 6393.
VIBRATION LEVELS
Vibration at the operator’s hand during normal operation is 6.1 m/s
2
63
64
1230
1030/1230 - SPECIFICATIONS
1230
64
1230
1030/1230 - SPECIFICATIONS
1230
L
2
W
2
H
2
W
4
A
3
B
C
DIMENSIONS
A Trench depth, maximum
Trench width
Boom travel down
C
1
F
Boom travel up
Headshaft height--digging chain
Length
Width
Height
Tread
Angle of departure
Wheelbase
L
4
E
1
E
N
2
Centerline trench to outside edge of machine, left
Centerline trench to outside edge of machine, right
Spoil discharge reach
32 in
47 in
26 in
65°
32 in
U.S.
36 in
4.3-6 in
60°
47°
8.60 in
88 in
15 in
17 in
10.6 in
METRIC
915 mm
110-150 mm
60°
47°
220 mm
2.2 m
810 mm
1.2 m
660 mm
65°
810 mm
381 mm
432 mm
270 mm
L
2
W
2
H
2
W
4
A
3
B
C
DIMENSIONS
A Trench depth, maximum
Trench width
Boom travel down
C
1
F
Boom travel up
Headshaft height--digging chain
Length
Width
Height
Tread
Angle of departure
Wheelbase
L
4
E
1
E
N
2
Centerline trench to outside edge of machine, left
Centerline trench to outside edge of machine, right
Spoil discharge reach
32 in
47 in
26 in
65°
32 in
U.S.
36 in
4.3-6 in
60°
47°
8.60 in
88 in
15 in
17 in
10.6 in
METRIC
915 mm
110-150 mm
60°
47°
220 mm
2.2 m
810 mm
1.2 m
660 mm
65°
810 mm
381 mm
432 mm
270 mm
1030/1230 - SPECIFICATIONS
1230
DIMENSIONS
A
2
Angle of approach
U.S.
35°
METRIC
35°
Dimensions based on 16x6.50x8 tires and 24” (610-mm) boom in transport position
GENERAL
Ditch Witch model 1230, self-propelled, pedestrian, manually steered, twowheel drive rigid frame, chain type trencher
OPERATIONAL
Vehicle speeds
U.S.
METRIC
Maximum transit forward
Maximim transit reverse
Digging chain speed
Spoils handling (single, open-end auger)
155 fpm
155 fpm
276 fpm
47 m/min
47 m/min
84 m/min
Outer diameter
Inner diameter
Length
Operating weight [with 33,000-lb (14 969-kg) test, two-pitch digging chain]
12 in
4 in
9 in
900 lb
305 mm
102 mm
229 mm
408 kg
POWER
Engine: Honda GX390
Fuel: gasoline
Cooling medium: air
Number of cylinders: 1
Displacement
U.S.
METRIC
Bore
Stroke
Gross power @ 3600 rpm
23.7 in
3
3.53 in
2.52 in
13 hp
389 cm
3
90 mm
64 mm
9.7 kW
65 1030/1230 - SPECIFICATIONS
1230
DIMENSIONS
A
2
Angle of approach
U.S.
35°
METRIC
35°
Dimensions based on 16x6.50x8 tires and 24” (610-mm) boom in transport position
GENERAL
Ditch Witch model 1230, self-propelled, pedestrian, manually steered, twowheel drive rigid frame, chain type trencher
OPERATIONAL
Vehicle speeds
U.S.
METRIC
Maximum transit forward
Maximim transit reverse
Digging chain speed
Spoils handling (single, open-end auger)
155 fpm
155 fpm
276 fpm
47 m/min
47 m/min
84 m/min
Outer diameter
Inner diameter
Length
Operating weight [with 33,000-lb (14 969-kg) test, two-pitch digging chain]
12 in
4 in
9 in
900 lb
305 mm
102 mm
229 mm
408 kg
POWER
Engine: Honda GX390
Fuel: gasoline
Cooling medium: air
Number of cylinders: 1
Displacement
U.S.
METRIC
Bore
Stroke
Gross power @ 3600 rpm
23.7 in
3
3.53 in
2.52 in
13 hp
389 cm
3
90 mm
64 mm
9.7 kW
65
66
1030/1230 - SPECIFICATIONS
1230
POWER
Maximum governed speed installed (no load)
Flywheel power @ 3200 rpm (full load)
Fuel consumption @3600 rpm
Maximum tilt angle
Fuel tank capacity
Engine oil capacity
POWER TRAIN
U.S.
3600 rpm
12 hp
.89 gph
20°
1.7 gal
2.3 pt
METRIC
3600 rpm
8.9 kW
3.4 L/h
20°
6.5 L
1.1 L
Ground drive transmission
Ground drive: hydrostatic, infinitely variable from zero to maximum, gearbox to axle, speed and direction controlled with single lever
Pump drive clutch: mechanical, hand-operated, spring-loaded, with tension roller for belt drive
Digging chain clutch: mechanical, hand-operated, spring-loaded with tension roller for belt drive
Tires
Drive, standard: 16x6.50x8
Drive, optional: 18x8.50x8
Trail: 13x5.00x6
Trencher drive: mechanical, belt drive to reduction drive, headshaft
Belt: “power band,” two-groove
Digging chain: 33,000 lb (16 969 kg) test
Chain drive sprocket: forged and tempered
Digging teeth: bolt-on cup teeth with hard-surfaced edge of tungsten carbide
Spoils handling drive: mechanical, attached to and rotates with headshaft
NOISE LEVELS
Operator 88 dBA sound pressure per ISO 6394
Exterior 101 dBA sound power per ISO 6393
VIBRATION LEVELS
Vibration at the operator’s hand during normal operation is 6.1 m/s
2
66
1030/1230 - SPECIFICATIONS
1230
POWER
Maximum governed speed installed (no load)
Flywheel power @ 3200 rpm (full load)
Fuel consumption @3600 rpm
Maximum tilt angle
Fuel tank capacity
Engine oil capacity
POWER TRAIN
U.S.
3600 rpm
12 hp
.89 gph
20°
1.7 gal
2.3 pt
METRIC
3600 rpm
8.9 kW
3.4 L/h
20°
6.5 L
1.1 L
Ground drive transmission
Ground drive: hydrostatic, infinitely variable from zero to maximum, gearbox to axle, speed and direction controlled with single lever
Pump drive clutch: mechanical, hand-operated, spring-loaded, with tension roller for belt drive
Digging chain clutch: mechanical, hand-operated, spring-loaded with tension roller for belt drive
Tires
Drive, standard: 16x6.50x8
Drive, optional: 18x8.50x8
Trail: 13x5.00x6
Trencher drive: mechanical, belt drive to reduction drive, headshaft
Belt: “power band,” two-groove
Digging chain: 33,000 lb (16 969 kg) test
Chain drive sprocket: forged and tempered
Digging teeth: bolt-on cup teeth with hard-surfaced edge of tungsten carbide
Spoils handling drive: mechanical, attached to and rotates with headshaft
NOISE LEVELS
Operator 88 dBA sound pressure per ISO 6394
Exterior 101 dBA sound power per ISO 6393
VIBRATION LEVELS
Vibration at the operator’s hand during normal operation is 6.1 m/s
2
1030/1230 - WARRANTY
67
WARRANTY
Ditch Witch Equipment and Replacement Parts
North American*
Limited Warranty Policy
Major Component Limited Warranty
Major components are warranted for a period of 1000 hours of use or one year, whichever occurs first, beginning on date of delivery of any such new product. The
Major Component Limited Warranty covers only Major Components listed under
Major Component Limited Warranty that are manufactured and distributed by The
Charles Machine Works, Inc. (“CMW”). Replacement parts and other serial numbered products (“Products”) that are not listed under Major Component
Limited Warranty, and non-major components are covered under Product Limited
Warranty.
Major Components are defined as:
• Frames.
• Differentials and parts contained within.
• Mechanical transmissions.
• Drive gearboxes and parts contained within.
• Hydraulic, hydrostatic, and fluid pumps, motors and components that control or protect pumps and motors.
• Auxiliary hydraulic control valves and electrical components used for controlling hydraulic components.
• Hydraulic cylinders and components excluding repair kits.
• Batteries, alternators, instruments, gauges, and protection components for electrical systems.
• Pierce Airrow bodies, strikers, and tailpieces.
Free replacement parts and labor will be provided at any authorized dealership for any part of Major Component which has a defect in material or workmanship within warranty period. Defects will be determined by an inspection of major component or part by CMW or its authorized dealer. The product containing a major component or part must be presented to CMW or its authorized dealer for inspection within 30 days of the date major component or part fails. CMW will provide the location of its inspection facilities or its nearest authorized dealer upon inquiry. CMW reserves the right to supply remanufactured replacement parts as it deems appropriate.
* Equipment owners in countries other than U.S., Canada, Mexico, and Puerto
Rico should refer to Ditch Witch International Warranty Policy.
1030/1230 - WARRANTY
67
WARRANTY
Ditch Witch Equipment and Replacement Parts
North American*
Limited Warranty Policy
Major Component Limited Warranty
Major components are warranted for a period of 1000 hours of use or one year, whichever occurs first, beginning on date of delivery of any such new product. The
Major Component Limited Warranty covers only Major Components listed under
Major Component Limited Warranty that are manufactured and distributed by The
Charles Machine Works, Inc. (“CMW”). Replacement parts and other serial numbered products (“Products”) that are not listed under Major Component
Limited Warranty, and non-major components are covered under Product Limited
Warranty.
Major Components are defined as:
• Frames.
• Differentials and parts contained within.
• Mechanical transmissions.
• Drive gearboxes and parts contained within.
• Hydraulic, hydrostatic, and fluid pumps, motors and components that control or protect pumps and motors.
• Auxiliary hydraulic control valves and electrical components used for controlling hydraulic components.
• Hydraulic cylinders and components excluding repair kits.
• Batteries, alternators, instruments, gauges, and protection components for electrical systems.
• Pierce Airrow bodies, strikers, and tailpieces.
Free replacement parts and labor will be provided at any authorized dealership for any part of Major Component which has a defect in material or workmanship within warranty period. Defects will be determined by an inspection of major component or part by CMW or its authorized dealer. The product containing a major component or part must be presented to CMW or its authorized dealer for inspection within 30 days of the date major component or part fails. CMW will provide the location of its inspection facilities or its nearest authorized dealer upon inquiry. CMW reserves the right to supply remanufactured replacement parts as it deems appropriate.
* Equipment owners in countries other than U.S., Canada, Mexico, and Puerto
Rico should refer to Ditch Witch International Warranty Policy.
68
1030/1230 - WARRANTY
Product Limited Warranty
Products are warranted for 90 days from date of delivery of any new product. Free replacement parts and labor will be provided at any authorized dealership for any product which has a defect in material or workmanship within warranty period.
Replacement parts are warranted for 90 days from date of delivery of any such replacement part. Any part of a product subject to ground contact is warranted only for defects in material or workmanship and only for the period of operational life of such part, which period shall not in any event exceed 90 days. Defects will be determined by an inspection of the product or part by CMW or its authorized dealer. The product or part must be presented to CMW or its authorized dealer for inspection within 30 days of the date of failure. CMW will provide the location of its inspection facilities or its nearest authorized dealer upon inquiry. CMW reserves the right to supply remanufactured replacement parts as it deems appropriate.
68
1030/1230 - WARRANTY
Product Limited Warranty
Products are warranted for 90 days from date of delivery of any new product. Free replacement parts and labor will be provided at any authorized dealership for any product which has a defect in material or workmanship within warranty period.
Replacement parts are warranted for 90 days from date of delivery of any such replacement part. Any part of a product subject to ground contact is warranted only for defects in material or workmanship and only for the period of operational life of such part, which period shall not in any event exceed 90 days. Defects will be determined by an inspection of the product or part by CMW or its authorized dealer. The product or part must be presented to CMW or its authorized dealer for inspection within 30 days of the date of failure. CMW will provide the location of its inspection facilities or its nearest authorized dealer upon inquiry. CMW reserves the right to supply remanufactured replacement parts as it deems appropriate.
1030/1230 - WARRANTY
69
Exclusions
from Major Component and Product Limited Warranty
Specifically excluded from Major Component and Product Limited Warranty are:
• Transportation charges related to repair, replacement, or inspection of products, major components, or parts.
• Parts subject to ground contact (including but not limited to drill pipe, downhole tools, digging chain, teeth and sprockets).
• All incidental or consequential damages.
• All defects, damages, or injuries caused by misuse, abuse, improper installation, alteration, neglect, or uses other than those for which products were intended.
• All defects, damages, or injuries caused by improper training, operation, or servicing of products in a manner inconsistent with manufacturer’s recommendations.
• All engines and engine accessories (these are covered by original manufacturer’s warranty).
• Parts which may be subject to another manufacturer’s warranty (such warranty will be available to purchaser).
• All implied warranties not expressly stated herein, including any warranty of fitness for a particular purpose and merchantability.
IF THE PRODUCTS ARE PURCHASED FOR COMMERCIAL PURPOSES AS
DEFINED BY THE UNIFORM COMMERCIAL CODE, THEN THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF AND THERE
ARE NO IMPLIED WARRANTIES OF ANY KIND WHICH EXTEND TO A
COMMERCIAL BUYER. ALL OTHER PROVISIONS OF THIS LIMITED
WARRANTY APPLY INCLUDING THE DUTIES IMPOSED.
Ditch Witch products have been tested to deliver acceptable performance in most conditions. This does not imply they will deliver acceptable performance in all conditions. Therefore, to assure suitability, products should be operated under anticipated working conditions prior to purchase.
This limited warranty applies to the owner of the product. Some states do not allow exclusion or limitation of incidental or consequential damages, so above limitation of exclusion may not apply. Further, some states do not allow exclusion of or limitation of how long an implied warranty lasts, so the above limitation may not apply. This limited warranty gives owner specific legal rights and the owner may also have other rights which vary from state to state.
1030/1230 - WARRANTY
69
Exclusions
from Major Component and Product Limited Warranty
Specifically excluded from Major Component and Product Limited Warranty are:
• Transportation charges related to repair, replacement, or inspection of products, major components, or parts.
• Parts subject to ground contact (including but not limited to drill pipe, downhole tools, digging chain, teeth and sprockets).
• All incidental or consequential damages.
• All defects, damages, or injuries caused by misuse, abuse, improper installation, alteration, neglect, or uses other than those for which products were intended.
• All defects, damages, or injuries caused by improper training, operation, or servicing of products in a manner inconsistent with manufacturer’s recommendations.
• All engines and engine accessories (these are covered by original manufacturer’s warranty).
• Parts which may be subject to another manufacturer’s warranty (such warranty will be available to purchaser).
• All implied warranties not expressly stated herein, including any warranty of fitness for a particular purpose and merchantability.
IF THE PRODUCTS ARE PURCHASED FOR COMMERCIAL PURPOSES AS
DEFINED BY THE UNIFORM COMMERCIAL CODE, THEN THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF AND THERE
ARE NO IMPLIED WARRANTIES OF ANY KIND WHICH EXTEND TO A
COMMERCIAL BUYER. ALL OTHER PROVISIONS OF THIS LIMITED
WARRANTY APPLY INCLUDING THE DUTIES IMPOSED.
Ditch Witch products have been tested to deliver acceptable performance in most conditions. This does not imply they will deliver acceptable performance in all conditions. Therefore, to assure suitability, products should be operated under anticipated working conditions prior to purchase.
This limited warranty applies to the owner of the product. Some states do not allow exclusion or limitation of incidental or consequential damages, so above limitation of exclusion may not apply. Further, some states do not allow exclusion of or limitation of how long an implied warranty lasts, so the above limitation may not apply. This limited warranty gives owner specific legal rights and the owner may also have other rights which vary from state to state.
70
1030/1230 - WARRANTY
For information regarding this limited warranty, contact CMW’s Product Support department, P.O. Box 66, Perry, OK 73077-0066, or contact your local Ditch Witch dealer.
First version: 1/91; Latest revision: 4/99
70
1030/1230 - WARRANTY
For information regarding this limited warranty, contact CMW’s Product Support department, P.O. Box 66, Perry, OK 73077-0066, or contact your local Ditch Witch dealer.
First version: 1/91; Latest revision: 4/99

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Enhanced control with precise hydraulics.
- Increased productivity with a powerful engine.
- Improved safety with a roll-over protective structure (ROPS).
- Versatile for multiple applications, from drilling to trenching.
- User-friendly controls for ease of operation.
- Durable construction for long-lasting performance.