HKTS5/HKTS6 harman/kardon
harman/kardon
HKTS 5/HKTS 6
Home Theater Speaker System
SERVICE MANUAL
harman/kardon, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797
Rev2
1/2004
HKTS5/HKTS6
harman/kardon
- CONTENTS -
BASIC SPECIFICATIONS……………………………….……….……….1
DETAILED SPECIFICATIONS
……..……………………….………..2
CONNECTIONS..………………………..……………..……….….……...3
OPERATION ………….…………………………….…….…….………….4
TROUBLESHOOTING……………….……………..………….………….5
SUB-TS5/TS6 EXPLODED VIEW..……………………..…..…….……...6
SUB-TS5/TS6 AMPLIFIER EXPLODED VIEW..….. …...…….….……...7
SUB-TS5/TS6 TEST PROCEDURE..…………………….. ……..……….8
HKTS 5/HKTS 6 MECHANICAL/SATELLITE PARTS LIST………..….9
HKTS 5/HKTS 6 PACKAGE..………………….……………..…….….....10
SUB-TS5/ TS6 BLOCK DIAGRAM..……………………. ………………11
SUB- TS5/ TS6 PCB DRAWINGS……..……………....……….……......12
SUB- TS5/ TS6 ELECTRICAL PARTS LIST …….……….…..………...15
SUB- TS5/ TS6 IC/TRANSISTOR PINOUTS…..……………………....18
SUB- TS5/ TS6 SCHEMATICS………..…………………………....….…19
HKTS 5/HKTS6 System
Frequency Response
35Hz – 20kHz (–6dB)
Satellites
Center
Subwoofer SUB-TS5/TS6
Recommended Power
10 – 70 watts
Impedance
8 ohms nominal
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1/2" dome, video-shielded
Midrange
One 3" driver, video-shielded
Dimensions (H x W x D)
4-5/8" x 3-1/8" x 3-3/4"
(117mm x 79mm x 93mm)
Weight
1.1 lb/0.5kg
Recommended Power
10 – 70 watts
Impedance
8 ohms nominal
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1/2" dome, videoshielded
Midrange
Dual 3" drivers, videoshielded
Dimensions (H x W x D)
3-1/2" x 7-5/8" x 3-3/4"
(89mm x 194mm x 93mm)
Weight
1.89 lb/0.86kg
Amplifier
100 watts RMS
Woofer
10" woofer, bass-reflex enclosure
Dimensions (H x W x D)
15-3/4" x 15-3/4" x 16-3/4"
(400mm x 400mm x 425mm)
Weight
33.5 lb/15.2kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
HKTS5/HKTS6
harman/kardon
SUB-TS5/TS6 Amplifier
LINE VOLTAGE
US 120vac/60Hz
Parameter
Yes/No
Yes
100w Powered Subwoofer Amplifier
Hi/Lo Line
Unit
108-132
Vrms
Specification
Unit
QA Test Limits
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
[email protected] Rated Power
THD @ 1 Watt
DC Offset
Damping factor
AB AB
4 Ohms
100 Watts
0.08 %
0.1 %
10 mV-DC
>100 DF
n/a
n/a
95
0.3
0.5
20
50
Input Sensitivity
Input Frequency
SUB Input
50 Hz
135 mVrms
50
±2dB
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
Residual Noise Floor
100
80
60
1.5
Residual Noise Floor
Input Impedance
SUB Line input
Filters
Low Pass (fixed or variable)
Slope & Q
Subsonic filter (HPF)
Slope & Q
1
dBA
dBr
dBr
mVrms
mVrms(max)
>15 K ohms
fixed
-dB/Octave
Hz
dB/Octave
Notes
Normal Operation
90
75
55
2.5
2
n/a
Conditions
Nominal
1 input driven
22k filter
22k filter
@ Speaker Outputs
Notes
External Sink required for Class AB
Z-curve required
Measured at speaker terminals, Output
power 90 Watts THD 0.1 %
Nominal Freq.
To Rated Power
1 input driven
SUB input driven only
rel. to rated power
A-Weighting filter
rel. to rated power
22k filter
rel. to 1W Output
22k filter
Volume @max, using RMS reading
DMM/VOM (or A/P)
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Nominal
±2dB
n/a
±2dB
n/a
Limiter (yes/no)
YES
--
n/a
Features
LFE Input
Phase Switch (yes/no)
Volume pot Taper (lin/log)
ATO
YES
NO
log
YES
functional
functional
functional
functional
BW Limited to 500 Hz
---
Input Configuration
SUB Line level
LFE
functional
Single RCA Input
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input Frequency
YES
50 Hz
--
functional
functional
ATO Level
2 mV
functional
[email protected] into Line Input w/ 1 ch.
driven
ATO Turn-on time
5 ms
functional
functional
Amp connected and AC on, then input
signal applied
T before muting, after signal is removed Auto turn of time (T) must be 10 > T <15
functional
AC Power Applied
Auto Mute/ Turn-OFF Time
Power on Delay time
15 minutes
3 sec.
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
5 mV-peak
50 mV-peak
50 mV-peak
10
100
100
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
Efficiency
Stand-by Input Power
13 Watts
15
@ nom. line voltage
185 Watts
195
@ nom. line voltage
Power [email protected] power
Protection
Short Circuit Protection
Thermal Protection
DC Offset Protection
Line Fuse Rating
YES
65 deg. C
---
functional
functional
Direct short at output
@1/8 max unclipped Power
YES
-2.5 Amps
functional
2.5
DC present at Speaker Out leads
Type-T or Slo Blo
2
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
100 Watts @ 4 Ohms nominal line voltage
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
External fuse with UL/SEMKO rated holder
HKTS5/HKTS6
harman/kardon
SPEAKER CONNECTIONS
Use the supplied RCA-type patch cord to
connect the line-level SUB or LFE output on
your receiver or amplifier to the SUB input
on the SUB-TS5 or SUB-TS6 subwoofer.
Connect the satellite and center speakers to
the corresponding speaker terminals on your
receiver or amplifier.
Make sure that you have configured your
surround sound processor for “Subwoofer
On.” The front left, front right, center and
rear speakers should all be set to “Small.”
When all connections have been made, plug
the AC power cord on the subwoofer into
an AC outlet.
Center
–
+
Left
Front
–
+
Right
Front
–
+
SUBTS5/TS6
Subwoofer
Line-Level
SUB Input
Left
Front
Right
Front
SUB/LFE
Out
Left
Rear
Left
Surround
–
+
3
Center
Receiver
Right
Rear
Right
Surround
–
+
HKTS5/HKTS6
harman/kardon
OPERATION
Move the Master Power switch (marked
“Power” ¡) to the “•” (On) position. The
HKTS 5/6 subwoofer will automatically turn
itself on or go into Standby mode, depending on whether or not a signal is being sent
to the HKTS 5/6 by your receiver or surround
processor, and provided that the Auto/On
switch ™ is moved to the left so that it is
in the “Auto” position.
When your receiver or amplifier is off, or is
not sending program material to the subwoofer, the subwoofer will be in Standby
mode and the LED ¢ on the amp panel
will turn red. When the subwoofer senses an
audio signal, it will automatically turn itself
on and the LED ¢ will turn green. If the
subwoofer does not sense a signal after
approximately twenty minutes, it will automatically go into Standby mode.
™
When the Auto/On switch ™ is switched to
the “On” position, the subwoofer will
remain on, whether or not program material
is playing.
If you will be away from home for an
extended period of time, or if the subwoofer will not be used, switch the Master
Power switch ¡ to the “Off” position.
£
¢
SUB-TS5/SUB-TS6
¡
Volume
Volume can be adjusted using the
Subwoofer Level Control £, as shown
below.
Subwoofer
Level
MIN
MAX
Subwoofer
Level
MIN
MAX
4
HKTS5/HKTS6
harman/kardon
TROUBLESHOOTING
If there is no sound from any of the
speakers:
• Check that receiver/amplifier is on and a
source is playing.
• Check that the powered subwoofer is
plugged in and its Power switch ¡ is
switched on to the “•” position.
• Check all wires and connections between
receiver/amplifier and speakers. Make sure
all wires are connected. Make sure none
of the speaker wires are frayed, cut or
punctured.
• Review proper operation of your
receiver/amplifier.
If there is no sound from the center
speaker:
• Check all wires and connections between
receiver/amplifier and speaker. Make sure
all wires are connected. Make sure none
of the speaker wires are frayed, cut or
punctured.
• If your receiver/processor is set in Dolby
Pro Logic* mode, make sure the center
speaker is not in phantom mode.
• If your receiver/processor is set in Dolby
Digital or DTS mode, make sure the
receiver/processor is configured so
that the center speaker is enabled.
If there is no sound coming from one
speaker:
• Check the “Balance” control on your
receiver/amplifier.
• Check all wires and connections between
receiver/amplifier and speakers. Make sure
all wires are connected. Make sure none
of the speaker wires are frayed, cut or
punctured.
• In Dolby* Digital or DTS® mode, make
sure that the receiver/processor is configured so that the speaker in question is
enabled.
• Turn off all electronics and switch the
speaker in question with one of the other
speakers that is working correctly. Turn
everything back on, and determine whether
the problem is in the same place: i.e., the
speaker that was working previously now
has no sound and the speaker that was not
working now sounds fine; or whether it has
moved: i.e., the speaker that was not working still has no sound and the speaker that
was working is still fine. If the problem is in
the same place, the source of the problem
is most likely with your receiver or amplifier,
and you should consult the owner’s manual
for that product for further information. If the
problem has followed the speaker, consult
your dealer for further assistance or, if
that is not possible, visit our Web site at
www.harmankardon.com for further
information.
If the system plays at low volumes
but shuts off as volume is increased:
• Check all wires and connections between
receiver/amplifier and speakers. Make sure
all wires are connected. Make sure none
of the speaker wires are frayed, cut or
punctured.
• If more than one pair of main speakers is
being used, check the minimum impedance
requirements of your receiver/amplifier.
5
If there is low (or no) bass output:
• Make sure the SUB input of the SUB-TS5/6
subwoofer and SUB or LFE output of your
receiver or amplifier are properly connected
by the RCA-type patch cord.
• Make sure the connections to the Speaker
Inputs have the correct polarity (+ and –).
• Make sure the subwoofer is plugged
into an active electrical outlet and its
Power switch ¡ is switched on to the
“•” position.
• Check the speaker setup (bass management) settings in your AVR receiver or
processor to make certain that the front,
center and surround speakers are configured for “Small,” and that the subwoofer is
set for “Yes” or “On.”
If there is no sound from the surround speakers:
• Check all wires and connections between
receiver/amplifier and speakers. Make sure
all wires are connected. Make sure none
of the speaker wires are frayed, cut or
punctured.
• Review proper operation of your
receiver/processor and its surround sound
features.
• Make sure the movie or TV show you are
watching is recorded in a surround sound
mode. If it is not, check to see whether your
receiver/processor has other surround
modes you may use.
• In Dolby Digital or DTS mode, make sure
your receiver/processor is configured so that
the surround speakers are enabled.
• Review the operation of your DVD player
and the jacket of your DVD to make sure
that the DVD features the desired Dolby
Digital or DTS mode, and that you have
properly selected that mode using both
the DVD player’s menu and the DVD
disc’s menu.
HKTS5/HKTS6
Ref.
#1
#2
#3
#4
#5
#6
#7
#8
#9
harman/kardon
Part Number
Not For Sale
(HKTS5) sz5321
(HKTS6) sz5930
25MF10DZB-DW02
06-t4205012
wi5448
06-t5345005
wi5447
wi5600
Not For Sale
Description
HKTS5/HKTS6 Enclosure
HK Logo
HK Logo
10" woofer (DCR = 3.4 ohms ±10%)
Amplifier/woofer screw t4*20
Foot (bumper)
Foot screw
Rubber foot
Port Tube
HKTS5/HKTS6 Amplifier Assembly
6
Qty
1
1
1
1
15
4
4
4
1
1
7
HKTS5/HKTS6
harman/kardon
HKTS 5/HKTS 6 TEST PROCEDURE
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
• Single RCA cable
General Unit Function (UUT = Unit Under Test)
1)
2)
3)
4)
5)
6)
From the signal generator, connect one line level (RCA) cable to the single SUB input.
On the front of the unit, turn the LEVEL control full counterclockwise.
Turn on generator, adjust to 150mV, 50 Hz.
Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
LED should now be Green; immediate bass response should be heard and felt from port tube opening.
Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable.
Sweep Function
1) Follow steps 3-6 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any
other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
5) Caution: when re-connecting woofer wires, observe proper polarity, as Faston connectors are the same size;
red wire should connect to terminal with red dot.
8
HKTS5/HKTS6
harman/kardon
MECHANICAL/SATELLITE PARTS LIST
Part number
Description
SATELLITES
HKTS 5/SAT-TS5
HKTS 6/SAT-TS6
22PF48JA-FW02
g255002
sz5322
sz5928
xc255002
xd255000
wi0409
wi5969
Complete satellite loudspeaker
Complete satellite loudspeaker
Woofer for Sats
grille
logo for HKTS 5/SAT-TS5
logo for HKTS 6/SAT-TS6
front enclosure
back enclosure
Wall-mount bracket for HKTS 5/SAT-TS5
Wall-mount bracket for HKTS 6/SAT-TS6
CENTER
HKTS 5/CEN-TS5
HKTS 6/CEN-TS6
22PF48JA-DW06
g255003
xc255001
xd255001
sz5371
sz5929
Complete Center loudspeaker
Complete Center loudspeaker
Woofer for Center
grille
front enclosure
back enclosure
logo for HKTS 5/CEN-TS5
logo for HKTS 5/CEN-TS6
SUB-TS5/TS6 SUBWOOFER EXTERNAL & HKTS5/HKTS6 PACKAGING
25MF10DZB-DW02
wi5447
wi5448
sz5321
ai5161
ai5262
wg5296
wg5452
at5073
wp5215
sal063-1
sal5009
sal5020
sal5044
10" woofer
Rubber foot (4)
foot (4)
logo
Owner's manual (HKTS5)
Owner's manual (HKTS6)
Outer carton (HKTS5)
Outer carton (HKTS6)
warranty card
Foam set
Wire set 20' (center)
Wire set 40' (surround)
Wire set 15' (front satellites)
Single RCA cable
OPTIONAL: Floor Stands for HKTS 5/SAT-TS5 satellites - FSTS1
9
HKTS5/HKTS6
Packaging
5
HKTS5/HKTS6
harman/kardon
11
HKTS5/HKTS6
harman/kardon
12
HKTS5/HKTS6
harman/kardon
13
HKTS5/HKTS6
harman/kardon
14
HKTS5/HKTS6
harman/kardon
SUB-TS5/TS6 Electrical Parts List
PART NO.
DESCRIPTION
QTY
Reference Designator
Resistors
11014152j26
RESISTOR 1.5K 1/4W ±5% CF
1
R265
11014472j26
RESISTOR 4.7K 1/4W ±5% CF
2
R147,150
11014681j26
RESISTOR 680 ohms 1/4W ±5% CF
2
R148,151
11016101j26
RESISTOR 100 ohms 1/6W ±5% CF
2
R120,215
11016102j26
RESISTOR 1K 1/6W ±5% CF
2
R124,254
11016103j26
RESISTOR 10K 1/6W ±5% CF
8
R134,230,232,235,237,240,260,264
11016105j26
RESISTOR 1M 1/6W ±5% CF
2
R143,259
11016123j26
RESISTOR 12K 1/6W ±5% CF
2
R135,139
11016124j26
RESISTOR 120K 1/6W ±5% CF
1
R233
11016151j26
RESISTOR 150 ohms 1/6W ±5% CF
1
R253
11016152j26
RESISTOR 1.5K 1/6W ±5% CF
6
R103,123,136,137,141,142
11016153j26
RESISTOR 15K 1/6W ±5% CF
5
R118,145,152,154,234
11016154j26
RESISTOR 150K 1/6W ±5% CF
2
R131,252
11016181j26
RESISTOR 180 ohms 1/6W ±5% CF
2
R111,114
11016182j26
RESISTOR 1.8K 1/6W ±5% CF
1
R153
11016183j26
RESISTOR 18K 1/6W ±5% CF
2
R238,262
11016205j26
RESISTOR 2.0M 1/6W ±5% CF
1
R257
11016223j26
RESISTOR 22K 1/6W ±5% CF
5
R128,129,133,255,263
11016332j26
RESISTOR 3.3K 1/6W ±5% CF
3
R106,107,144
11016392j26
RESISTOR 3.9K 1/6W ±5% CF
2
R105,108
11016393j26
RESISTOR 39K 1/6W ±5% CF
1
R126
11016470j26
RESISTOR 47 ohms 1/6W ±5% CF
4
R112,113,115,116
11016471j26
RESISTOR 470 ohms 1/6W ±5% CF
1
R140
11016472j26
RESISTOR 4.7K 1/6W ±5% CF
4
R110,125,130,258
11016473j26
RESISTOR 47K 1/6W ±5% CF
4
R101,219,250,251
11016560j26
RESISTOR 56 ohms 1/6W ±5% CF
1
R117
11016563j26
RESISTOR 56K 1/6W ±5% CF
1
R104
11016682j26
RESISTOR 6.8K 1/6W ±5% CF
1
R109
11010821jk1
RESISTOR 820 ohms 1W ±5%
1
R132
110122r2j15
RESISTOR 2.2 ohms 1/2W ±5%
1
R127
11016332j26
RESISTOR 3.3K 1/6W ±5% CF
1
R266
11020331jk2
RESISTOR 330 ohms 2W ±5%
1
R146
11020331jk3
RESISTOR 330 ohms 2W ±5%
1
R149
11350r10j20
CEMENT RESISTOR 0.1 ohms 5W ±5%
2
R121,122
11403302m0
POT 3K 0.3W ±20%
1
R138
115h503a101
VARIABLE RESISTOR D16 50K/1 A
1
VR201
15
HKTS5/HKTS6
PART NO.
harman/kardon
DESCRIPTION
QTY
Reference Designator
Capacitors
1302b101k503 100pf 50V ±10%
1
C220
1302b102k503 1000pf 50V ±10%
1
C116
1302b221k503 220pf 50V ±10%
2
C212,230
1302f104z503
9
C108,113,115,119,232,236,237,240,241
0.1uf 50V +80/-20%
1303f473m503 0.047uf 50V ±20%
1
C106
130sl470k503
47pf 50V +350/-1000 ±10%
1
C229
132104j503
0.1uf 50V ±5%
4
C107,221,222,224
132223ja03
0.022uf 100V ±5%
4
C124,125,126,128
132473j503
0.047uf 50V ±5%
1
C223
1353105m50
1uf 50V
3
C105,112,228
1353106m50
10uf 50V
2
C219,231
1353107m16
100uf 16V
6
C109,117,120,234,238,242
1353226m50
22uf 50V
2
C114,118
1353227m10
220uf 10V
2
C129,130
1353227m16
220uf 16V
2
C111,233
1353476m25
47uf 25V
1
C103
1302g472md00 4700pf 400V ±20%
1
132223ja03
0.022uf 100V ±5%
2
C123,127
1353107m16
100uf 16V
1
C110
1353226m50
22uf 50V
1
C225
1354688m50
6800uf/50V
2
C121,122
192027c1815gr 2SC1815GR NPN TRANS
8
Q102,111,112,113,118,206,207,208
192028a1015gr 2SA1015GR PNP TRANS
2
Q114,116
1921672n5551 2N5551 NPN TRANS
2
Q103,109
1921682n5401 2N5401 PNP TRANS
2
Q104,110
197131n4148
1N4148
9
D101,103,105,108,206,207,208,214,215
19915000335
3.3V 1/2W ZENER
2
D102,205
19915000625
6.2V 1/2W ZENER
2
D106,107
19915001605
16V 1/2W ZENER
1
D109
19016tl074cn
TL074CN QUAD OP-AMP
1
U202
192011d669a
2SD669A NPN TRANS
1
Q106
192012b649a
2SB649A PNP TRANS
Semiconductors
1
Q105
192021c1815gr 2SC1815GR NPN TRANS
2
Q101,115
192021tip35c
TIP35C NPN TRANS
1
Q107
192022tip36c
TIP36C PNP TRANS
1
Q108
192201d882y
KSD882Y NPN TRANS
1
Q117
192202b772y
KSB772Y PNP TRANS
1
Q119
19006m4558d
OPA 4558D DUAL OP-AMP
2
U101,203
16
HKTS5/HKTS6
harman/kardon
PART NO.
DESCRIPTION
QTY
Reference Designator
19510204hgw
LED 204HGW
1
D209
19700kbl405
4A 500V KBL405 BRIDGE
1
D110
197101n4002
1N4002
1
D104
171udhss124d 5A 24V UDH-SS124D RELAY
1
RY101
1740rcb242vpg JACK RCB
1
JK203
180tms7210v
SWITCH SLIDE MS7210V
1
SW201
150e8604107
TRANSFORMER
1
152u602015
LINE CORD SVT FT-2 6FT
1
154u25006t0
FUSE 2.5A 250V 20mm
1
155520020
FUSE HOLDER R3-11
1
180pbr12c11s
PUSH SW BR12C11S
1
SW101
11016103j26
RESISTOR 10K 1/6W ±5% CF
7
R301,302,303,304,308,309,314
11016223j26
RESISTOR 22K 1/6W ±5% CF
2
R310,312
11016333j26
RESISTOR 33K 1/6W ±5% CF
1
R305
11016474j26
RESISTOR 470K 1/6W ±5% CF
1
R307
11016751j26
RESISTOR 750 ohms 1/6W ±5% CF
2
R311,313
11016755j26
RESISTOR 7.5M 1/6W ±5% CF
1
R306
1302f104z503
0.1uf 50V +80/-20%
2
C305,306
132103j503
0.01uf 50V ±5%
2
C302,3
1353226m50
22uf 50V ±20%
1
C301
1353476m25
47uf 25V ±20%
Miscellaneous
FS101
LIMITER PCB
1
C304
192027c1815gr 2SC1815GR B91
2
Q301,302
197131n4148
1N4148
2
D301,302
1759f40hr2
40PIN PITCH=2.54mm HR2*4
19016tl074cn
TL074CN QUAD OP-AMP
17
0.15
P301
1
U301
harman/kardon
HKTS5/HKTS6
18
HKTS5/HKTS6
harman/kardon
19
HKTS5/HKTS6
harman/kardon
20
HKTS5/HKTS6
harman/kardon
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement