Dual XRM47BT Installation & Owner's Manual

Add to my manuals
14 Pages

advertisement

Dual XRM47BT Installation & Owner's Manual | Manualzz

XDM16BT

INSTALLATION/OWNER'S MANUAL

AM/FM Receiver with Bluetooth and Fixed Face

XDM16BT INSTALLATION

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.

• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Mounting the Head Unit:

Typical DIN mounting

Step 1:

Insert the mounting sleeve into the installation kit or dashboard.

Single DIN

Dashboard or

Installation Kit

Mounting Sleeve

Step 2:

Bend multiple mounting tabs around the mounting sleeve until the mounting sleeve is secure.

Single DIN

Dashboard or Installation Kit

Mounting Tabs

Mounting Sleeve

2

Step 3:

Connect all wiring harnesses and slide the head unit into the mounting sleeve until it clicks into place.

Mounting the Head Unit:

ISO mounting

Using the existing brackets or the brackets supplied with the installation kit, mount the brackets to the sides of the head unit with the screws supplied with the head unit.

Single DIN

Dashboard or Installation Kit

Head Unit

Mounting Sleeve

Single DIN

Decorative

Bezel

New

Radio

Existing

Brackets

XDM16BT INSTALLATION

Wiring Diagram

FUSE

When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio.

The unit uses one 10 amp ATM fuse located beside the Heat Sink

3

1

XDM16BT OPERATION

2 3

Control Locations

4 5 6

4

18 17 16 15 14 13 12 11 10 9 8 7

17

16

15

14

13

12

4

5

6

1

2

3

Power

Band

Mute

Volume Knob

Automatically Store

USB Port

7

8

Auxiliary Input

Preset 6 / Folder Up

9

10

Preset 5 / Folder Down

Preset 4 / Random

11

Preset 3 / Repeat

12

Preset 2 / Intro

15

16

13

14

17

18

Preset 1 / Play/Pause

Display

Mode

Reset

Tune Up

Tune Down

1 2

3

4

5

6

7

8

9

10

11

7

8

5

6

9

3

4

1

2

Mode

Volume Up

Power

Audio

Tune Up

Volume Down

Band

Preset 3 / Repeat

Preset 2 / Intro

14

15

12

13

16

10

11

17

Preset 6 / Folder Up

Mute

AS/PS

Preset 5 / Folder Down

Preset 4 / Random

Preset 1 / Play / Pause

Bluetooth Talk

Tune Down

XDM16BT OPERATION

Power On/Off

General Operation

Press the button to turn the unit on. Press again to turn the unit off.

Changing Modes

Volume

Mute

Auxiliary Inputs

Reset

Press MODE to select between Radio, USB, Auxiliary Input and Bluetooth. Modes of operation are shown in the display.

Adjust volume using the volume knob (00-43).

Press to silence the audio. Press again to resume listening at the previously selected volume.

Insert a 3.5mm cable in the unit's front AUX port.

Press the RESET button to reset the unit back to the factory settings if abnormal operation occurs. The reset button is located on the front panel.

Setting the Clock

Display

Audio / Menu

With the unit on, press DISP to display clock time. Press and hold DISP until the hours begins to flash, then release.

Press the TUNE then press the DISP, the minutes begins to flash, press the

TUNE nn nn

and TUNE 

and TUNE  ll ll

to adjust the hours,

button to adjust the minutes.

Press DISP momentarily to save the selected time.

Press DISP to toggle display between various displayed information.

Press the volume knob momentarily to select between audio functions.

Press and hold the volume knob for more than two seconds to select between the menu functions.

Rotate the volume knob left/right to adjust or activate the desired function/audio.

5

6

XDM16BT OPERATION

AM/FM Tuner Operation

Seek Tuning

Press TUNE nn

or TUNE  next strong station.

ll

to seek to the previous or

Manual Tuning

Press and hold TUNE nn

or TUNE  tuning mode, then press TUNE nn ll to enter manual

or TUNE  ll momentarily to change radio frequency up or down one step at a time. Press and hold TUNE advance quickly. nn

or TUNE  ll to

Band 

Storing Presets

Recalling Presets

Automatically Store

Preset Scan Stations

Press BAND to select between FM1, FM2, FM3, AM1 and

AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.

Up to 18 FM and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display.

Preset stations can be recalled any time by pressing the corresponding preset button.

Press and hold AS/PS for more than 2 seconds to store

18 FM stations and 12 AM stations automatically.

Press AS/PS to recall each preset staion that stored in the memories in each band.

XDM16BT OPERATION

Playing MP3 Files

Track Select

Fast Forward

 and Reverse

Pause

Folder Access

Repeat

Random

Intro

USB Operation

To play MP3 files, insert a USB device containing MP3 files.

Press TUNE 

Press TUNE track.

ll to skip to the beginning of the next track. to skip to the beginning of the previous

Press and hold TUNE  reverse a track. ll

or TUNE nn to fast forward or

Press

Press l

/ II to temporarily stop USB playback.

l

/ II again to resume playback.

Folders can be found by pressing Folder Up or Folder Down.

About one second after the folder name is displayed, the first file under the selected folder will be displayed and playback will begin.

Press RPT to toggle between RPT ALL, RPT FLR and RPT

ONE.

• RPT ALL - Plays all tracks on USB device.

• RPT ONE - Continuously repeats selected track.

• RPT FLR - Continuously repeats all files in current folder.

Press RDM to play tracks in random order; press again to cancel the RDM function.

Press

INT

to play the first 10 seconds of each track; press again to cancel the INT function.

7

8

XDM16BT OPERATION

Preparation

Bluetooth Operation

Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.

Pairing a New

Device

The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details.

The device name is “Dual Media Player”.

The Bluetooth passcode is "1234”.

Note: The head unit can be in any mode of operation when pairing is performed.

Streaming Audio

Troubleshooting

The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit.

The following functions can be used to control the music:

• Press ll

to skip to the next available audio track.

• Press nn

to skip to the previous audio track.

• Press l

/

playback.

II to toggle between play and pause during

XDM16BT OPERATION

Troubleshooting 

Problem

Unit will not turn on 

(no power)

Unit has power 

(but no sound)

Unit blows fuses

NO FILE appears  on display

NO SUPPORT appears  on display

Cause

Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage

Black wire not connected

Fuse blown

Speaker wires not connected

One or more speaker wires touching each other or touching chassis ground

Yellow or red wire touching chassis ground

Speaker wires touching chassis ground

Incorrect fuse rating

No playable MP3 files found on the device

An invalid ID3 tag version is present

Action

Check connections for proper voltage (11~16VDC)

Check connection to ground

Replace fuse

Check connections at speakers

Insulate all bare speaker wires from each other and chassis ground

Check for pinched wire

Check for pinched wire

Use fuse with correct rating

Check the device for valid

MP3 files

Version 1.0 to 2.0 ID3 tags are supported.

9

XDM16BT OPERATION

Limited One Year Warranty

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.

Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product

(whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.

Who is covered? This warranty is extended

to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U.S.A.

What is covered? This warranty covers all

defects in material and workmanship in this product. The following are not covered: software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.dualav.

com.

What to do?

1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.

2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.

3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.

4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:

• Call us toll-free at 1-866-382-5476

• E-mail us at [email protected]

Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.

10

XDM16BT OPERATION

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

11

XDM16BT OPERATION

Specifications

FM Tuner

Tuning range: 87.5MHz-107.9MHz

Usable sensitivity: 8.5dBf

50dB quieting sensitivity: 10dBf

Stereo separation @ 1kHz: >30dB

Frequency response: 30Hz-13kHz

AM Tuner

Tuning range:

530kHz-1710kHz

Usable sensitivity: <42dBu

Frequency response: 30Hz-2.2kHz

General

Speaker output impedance: 4~8 ohms

Line output voltage:

2 Volts RMS

Dimensions: 7" x 3.8" x 2" (178 x 97 x 50 mm)

Design and specifications subject to change without notice.

CEA-2006 Power Standard Specifications

(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)

Power Output: 16 Watts RMS x 4 channels at 4 ohms and < 1% THD+N

Signal to Noise Ratio: 75dBA (reference: 1 watt into 4 ohms)

12

XDM16BT OPERATION

Notes

13

Dual Electronics Corp.

Toll Free: 1-866-382-5476 www.dualav.com

©2016 Dual Electronics Corp. All rights reserved.

Other trademarks and trade names are those of their respective owners.

NSA0816-V01

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement