Quick Start Guide
Quick Start Guide
NI-700
For more detailed installation, configuration, programming, file transfer, and
operating instructions, refer to the NetLinx Integrated Controllers Instruction
Manual, available on-line at www.amx.com.
NI-700 Specifications (Cont.)
Rear Panel:
• RS-232/422/485 (Ports 1 & 2): Two RS-232/422/485 control ports
using DB9 (male) connectors with XON/XOFF (transmit on/transmit
off), CTS/RTS (clear to send/ready to send), and 300-115,200 baud.
• IR RX (Port 5): This single port is used to connect one or more
(8 maximum) IRX-SM+ swivel mount or IRX-DM+ Decora mount IR
receivers.
The IR RX port functions using AMX IR codes (38 KHz and 455 KHz)
and works ONLY with AMX IR Receivers such as the IRX-DM+ and
IRX-SM+.
• Digital I/O (Port 4): Four-channel binary I/O port for contact closure
with each input being capable of voltage sensing. Input format is
software selectable with interactive power sensing for IR ports.
• IR/Serial (Port 3): This single port is capable of generating IR with the
use of an IR emitter (while in IR mode). This port can support
high-frequency carriers of up to 1.142 MHz and can also generate IR
with no carrier frequency.
• AXlink LED: One green LED indicates the state of the AXlink port.
• AXlink port: 4-pin 3.5 mm mini-Phoenix (male) connector provides data
and power to external control devices.
• Ethernet port: LEDs show communication activity, connections,
speeds, and mode information:
L/A-link/activity - Green LED lights On when the Ethernet cables are
connected and terminated correctly and blinks when receiving
Ethernet data packets.
SPD-speed - Yellow LED lights On when the connection speed is
100 Mbps and turns Off when the speed is 10 Mbps.
• Power port: 2-pin 3.5 mm mini-Phoenix (male) connector
Included
Accessories:
•
•
•
•
•
•
NI-700 Quick Start Guide (93-2105-03)
One 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)
One 4-pin 3.5 mm mini-Phoenix female AXlink connector (41-5047)
One 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)
One CC-NIRC IR Emitter (FG10-000-11)
OpenSSL Warranty and Licensing Information (93-2105-05)
Optional
Accessories:
•
•
•
•
•
•
•
•
•
•
2-pin Black Male Phoenix Connector (3.5mm) (41-5026)
AC-RK Accessory Rack Kit (FG515)
CC-NIRC IR cables (FG10-000-11)
CC-NSER IR/Serial cables (FG10-007-10)
CSB Cable Support Bracket (FG517)
PSN2.8: Power supply (FG423-17)
PSN4.4: Power supply(FG423-45)
PSN6.5: Power supply (FG423-41)
STS, Serial To Screw Terminal (FG959)
Surface Mount Bracket Accessory (FG525)
(front)
(rear)
FIG. 1 NI-700 NetLinx Integrated Controller (front and rear views)
Overview
The NI-700 unit (FG2105-03) is geared to meet the specific control and
automation needs of a single room environment, where both price and
functionality are the driving requirement. This product is configured to control a
limited number of video players, projectors, lighting, thermostats, and other
electronic equipment. The NI-700 provides support for 1 IR/Serial Output port,
2 RS-232/RS-422/RS-485 ports, 4 Digital Input/Output ports, and 1 IR RX port.
ATTENTION!
When working with the NI-700 Integrated Controller, verify you are using the
latest version of NetLinx Studio v 2.2 build 78 or higher (available for download
from www.amx.com).
NI-700 Specifications
Port Assignment and Functionality
Dimensions (HWD):
• 1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)
• 1 rack unit high
NetLinx Port Assignments
Power:
• 280 mA @ 12 VDC
Port
ICSP Port #
Memory:
•
•
•
•
Serial Port 1
1
Serial Port 2
2
32 MB SDRAM
16 MB Flash chip
512 Kb of Non-volatile SRAM
Refer to the NetLinx Integrated Controllers Instruction Manual for more
information.
Microprocessor:
• 304 MIPS using a PowerPC™ processor
Weight:
• 1.30 lbs (0.59 kg)
Enclosure:
• Metal with black matte finish
Front Panel:
• Program Port: RS-232 DB9 connector (male) can be connected to a
DB9 port on a PC. This port can be used with both Serial and NetLinx
commands.
• Configuration DIP Switch: Use this DIP switch to set the communication
parameters for the Program port.
• IR RX LED: Red LED lights to indicate when IR data is being received
via the rear IR RX port.
• IR LED: Red LED lights to indicate transmission of IR or Serial data
via the rear IR port.
• I/O LEDs: Four yellow LEDs light when the rear I/O channels 1-4 are
active. LED indicator for each I/O port reflects the state of that
particular port.
• Serial LEDs: Two sets of red and yellow LEDs light to indicate the rear
DB9 Ports 1 & 2 are transmitting or receiving RS-232, 422, or 485
data. These LEDs do not reflect changes in either the RTS or CTS
when hardware handshaking is used.
• LINK/ACT: Green LED lights when the Ethernet cable is connected and
an active link is established. This LED also blinks when receiving
Ethernet data packets.
• Status: Green LED lights to indicate that the system is programmed
and communicating properly.
• Output: Red LED lights when the Controller transmits data, sets
channels On and Off, sends data strings, etc.
• Input: Yellow LED lights when the Controller receives data from button
pushes, strings, commands, channel levels, etc.
• ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the
device.
NetLinx Integrated Controller
IR Port
3
I/O Port
4
IR RX Port
5
Ethernet Ports used by the NI Controller
Ethernet Port Usage
Port type
Description
Standard Port #
ICSP
Peer-to-peer protocol used for both Master-to-Master and
Master-to-device communications.
1319 (UDP/TCP)
Telnet
The NetLinx Telnet server provides a mechanism to
configure and diagnose a NetLinx system.
23 (TCP)
HTTP
The Master has a built-in web server that complies with the
HTTP 1.0 specification and supports all of the required
features of HTTP v1.1.
80 (TCP)
HTTPS
The Master has a built-in SSL protected web server.
443 (TCP)
FTP
The on-board Master has a built-in FTP server that
conforms to RFC959.
21/20 (TCP)
Internet Inside
The Internet Inside feature the Master uses, by default, is
port 10500 for the XML based communication protocol.
This port is connected to by the client web browser’s JVM
when Internet Inside control pages are retrieved from the
on-board Master’s web server.
10500 (TCP)
Connections and Wiring
Baud Rate Settings
FIG. 2 shows the layout of the connectors and components located on the rear
of the NI-700 NetLinx Integrated Controller.
Baud Rate
Position 5
Position 6
Position 7
9600 bps
OFF
ON
OFF
ON
38,400 bps (default)
OFF
ON
ON
ON
57,600 bps
ON
OFF
OFF
OFF
115,200 bps
ON
ON
ON
ON
Ethernet
RS-232/422/485 (Ports 1 & 2)
PORT 2
PORT 1
ETHERNET
10/100
I/O
IR RX
IR
AXP
1
AXM
2
SPD
12VDC
PWR
3
GND
4
GND
PWR
AUX
GND
IR IN
+12V
L/A
Position 8
Note: DIP switch 1 activates/deactivates the Program Run Disable Mode. DIP
Switches 2,3, and 4 must remain OFF at all times.
AXlink
PWR
Setting the Configuration (Program Port) DIP Switch
IR RX
(Port 5)
I/O (Port 4)
Rear
AXLink
port
IR/Serial
(Port 3)
AXLink LED
(green)
1.
PWR
2.
Disconnect the power supply from the rear 2-pin PWR (green)
connector.
Set DIP switch positions according to the information listed in the previous
Baud Rate Settings table.
Reapply power to the unit.
FIG. 2 NI-700 rear connectors and components
3.
Wiring a power connection
Preparing the NI-700 for Communication
Use any standard PSN power supply (usage dependent) to supply power to the
NI-700 through the 2-pin 3.5 mm mini-Phoenix connector on the rear panel
(FIG. 2).
1.
The incoming PWR and GND cable from the PSN power supply must be
connected to the corresponding locations within the PWR connector. Refer to
the NetLinx Integrated Controllers Instruction Manual for more detailed wiring
connection information.
2.
3.
4.
RS-232/422/485 wiring connector information
FIG. 3 shows the pinout and wiring specification information for the rear
RS-232/RS-422/RS-485 (DB9) Device Ports. These ports support most
standard RS-232 communication protocols for data transmission
(NI-700 uses Ports 1 & 2).
5.
6.
DB9 Serial Port pinouts (male connector)
9
8
5
4
3
2
1
7
6
RS-232
RS-422
Pin 1: RX Pin 4: TX +
Pin 5: GND
Pin 6: RX +
Pin 9: TX -
Pin 2: RX signal
Pin 3: TX signal
Pin 5: GND
Pin 7: RTS
Pin 8: CTS
RS-485
Pin 1: A (strap to 9)
Pin 4: B (strap to 6)
Pin 5: GND
Pin 6: B (strap to 4)
Pin 9: A (strap to 1)
7.
8.
9.
10.
11.
Male
FIG. 3 RS-232/422/485 DB9 (male) connector pinouts
Communicating with the Integrated Controller via Ethernet
Ethernet 10/100 Base-T Connector
A standard CAT5 Ethernet cable provides 10/100 network connectivity between
the Integrated Controller and the network (FIG. 4).
L/A - Link/Activity LED lights
(green) when the Ethernet
cables are connected and
terminated correctly.
ETHERNET
10/100
L/A
SPD
Launch NetLinx Studio 2.2 (default location is Start > Programs > AMX
Control Disc > NetLinx Studio > NetLinx Studio 2.2).
Select Settings > Master Communication Settings, from the Main
menu, to open the Master Communication Settings dialog box.
Click the Communications Settings button to open the
Communications Settings dialog.
Click the NetLinx Master radio button (from the Platform Selection
section) to indicate that you are working with a NetLinx Master
(NI-Series of Integrated Controllers).
Click the Serial radio button (from the Transport Connection Option
section) to indicate you are connecting to the Master via a COM port.
Click the Edit Settings button (on the Communications Settings
dialog) to open the Serial Settings dialog and set the COM port
parameters for the COM port being used to communicate to the NetLinx
Master.
Click the OK button three times to return to the main application.
Right-click within the Online tab and select Refresh System.
Assign a System Value by using Diagnostics > Device Addressing from
the Main menu and enter the new and current system values.
Click the Change Device/System Number button and when finished
click Done.
Select Tools > Reboot the Master Controller > Continue to restart the
Master and incorporate any changes.
SPD - Speed LED lights (yellow) when
the connection speed is 100 Mbps
and turns Off when the speed
is 10 Mbps.
Once the NI-700 has been configured according to the steps outlined above, it
is ready for Ethernet communication:
1.
2.
FIG. 4 Layout of Ethernet LEDs
Note: On Netlinx Masters (such as those aboard the NI-700), from within the
Telnet or Terminal applications; you can send the SET ETHERNET MODE
command to assign the speed of your Ethernet connection.
Sample NI-700 command:
3.
4.
5.
6.
SET ETHERNET MODE AUTO
The NI-700 only allows you to set the Ethernet mode to AUTO negotiate
the Ethernet connection speed. Using any of the other connection modes
(10 Half/Full or 100 Half/Full) results in an error message.
7.
8.
Connect an Ethernet cable to the units’ rear Ethernet connector.
Select Diagnostics > Network Address from the Main menu and either
use the:
- GET IP button (to obtain a DHCP Address from the DHCP Server),
click SET IP to assign the new address and then press the Done button to
finish the process.
- SET IP button (to set/specify a pre-reserved IP Address to the
Master), click this button and then press the Reboot Master button to
restart the Master and incorporate any changes.
Repeat steps 2 - 4 from the above section.
Click the TCP/IP radio button (from the Transport Connection Option
section) to indicate you are connecting to the Master via an IP.
Click the Settings button.
Enter the TCP/IP Address (either the obtain or assigned address) from
step 2.
Click the OK button three times.
Right-click within the Online Tree tab and select Refresh System.
Program Port Baud Rate Settings
The Configuration DIP switch is located on the front panel. Use this DIP switch
to set the baud rate for the Program Port, according to the settings shown in the
following table. Make sure the baud rate you set matches the baud rate on your
PC's NetLinx COM Settings before programming the unit.
By default, the baud rate is set to 38,400 (bps).
AMX Corporation reserves the right to alter specifications without notice at any time.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
060-004-2692 8/04 ©2004
AMX Corporation. All rights reserved. The AMX logo is a trademark of AMX Corporation. AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2105-03
REV: B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement