Entone Remote remote control Instructions

The Entone Remote is a remote control for the Entone box. It needs to be programmed to operate properly. It needs to be told how to run your television, which ‘stream’ it should change the channels for, and which Set Top Box (STB) (yours—not your neighbors) it is supposed to control.

PDF Download

Document

These instructions are for the Entone Remote used with the Entone box.

Your remote control needs to be programmed to operate properly. It needs to be told how to run your television, which ‘stream’ it should change the channels for, and which Set Top Box (STB)

(yours—not your neighbors) it is supposed to control.

1. Does the remote turn on/off the TV and control volume?

If YES, proceed to next question.

If NO, program remote using this procedure: a. Manually turn on the TV. (or auxiliary device) b. Press and release the TV key. c. Press and hold the Setup key until the key blinks twice and then release. d. The TV key will stay lit. Press the Power key once. e. Aim the remote at the TV and press and release Channel Up. The remote will auto scan at 10 second intervals. The TV key will be on, blinking every 10 seconds. f. If the TV turns off, a working code has been found. Press OK once to lock in the code.

The TV key will blink twice. g. If all codes are exhausted, the TV key will blink fast 7 times and the search will be terminated.

2. Can you change channels or see the guide?

If YES, proceed to next question.

If NO, the remote needs to be programmed to control the correct stream. a. Be sure that the RF antenna is attached to the ‘remote antenna’ port on the back of the

STB. b. ON THE STB, press and hold the ‘OK‘ button for 10 seconds. When you release the button, the STB display will read ‘RC REG’. c. ON THE REMOTE, press and hold the ‘STB’ button for 10 seconds. The ‘STB’ button will light up and stay lit. Release the ‘STB’ button. d. ON THE REMOTE, press and release the ‘STB’ button. Both the ‘STB’ and the ‘AUX’ buttons will illuminate. e. ON THE REMOTE, enter number for the stream:

- 0 for infrared Stream 1 (Use “0” if the remote will always be used in the same room as the box. Also, use “0” if you are using the Entone Amulet single stream box.)

- 1 for UHF Stream 1 (Channel 10)

- 2 for UHF Stream 2 (Channel 23)

- 3 for UHF Stream 3 (Channel 39) f. ON THE REMOTE, the ‘STB’ button will blink twice to indicate the registration was successful. ON THE STB, the display will read ‘RC REG Dx’ to indicate the registration was successful.

Helpful Hint: When powering up, push the STB button every time.

If you still are having problems with your remote, please contact ITC at 1-800-417-8667.

Hello! I am an AI chatbot specifically trained to assist you with the Entone Entone Remote remote control Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Control TV power and volume
Change channels
Access guide
Programmable for different TV and STB models
Infrared and UHF stream support
Auto scan for TV codes
Stream registration on STB
Simple setup

Frequently asked questions

Follow the steps in the document, starting with step 1. You will need to manually turn on your TV and use the TV key on the remote to begin the programming process.

'Stream' refers to the different ways your Entone box can receive and transmit signals. It can be infrared (IR) or UHF, and there are multiple UHF channels (Stream 1, Stream 2, Stream 3). You need to program the remote to use the correct stream based on your setup.

Registering your remote with the STB ensures proper communication between them for channel changing, guide access, and other functions. Without registration, the remote may not work correctly.

You need to program the remote to work with your TV. Follow the steps in section 1 of the instructions to manually program the remote using the TV key and power key.

This means that the remote needs to be programmed to control the correct stream on your Entone box. Follow the steps in section 2 of the instructions to program the remote for the correct stream.