G560 HMM
Lenovo G560
Hardware
Maintenance
Manual
Note:
Before using this information and the product it supports, be sure to read the general information under
“Notices” on page 92
First Edition (Jan. 2010)
© Copyright Lenovo 2010. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at
private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R.
2.101 with limited and restricted rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services
are delivered pursuant a General Services Administration ″GSA″ contract, use, reproduction, or
disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
© 2010 Lenovo
Contents
About this manual ....................................... iv
Safety information ........................................ 1
General safety ................................................ 2
Electrical safety .............................................. 3
Safety inspection guide .................................. 5
Handling devices that are sensitive to
electrostatic discharge .................................... 6
Grounding requirements ................................. 6
Safety notices: multilingual translations.......... 7
Laser compliance statement......................... 14
Important service information ................... 16
Strategy for replacing FRUs ......................... 16
Strategy for replacing a hard disk drive ............17
Important notice for replacing a system board ....17
How to use error message ...............................17
Strategy for replacing FRUs for CTO,
CMV, and GAV.............................................. 18
Product definition ..............................................18
FRU identification for CTO, CMV, and GAV
products ............................................................18
Important information about replacing RoHS
compliant FRUs ............................................ 20
General checkout ...................................... 21
What to do first ............................................. 22
Power system checkout................................ 23
Checking the AC adapter .................................23
Checking operational charging .........................23
Checking the battery pack ...............................24
Related service information ...................... 25
Restoring the factory contents by using
OneKey Recovery ........................................ 25
Restore of factory default .................................25
Using recovery disks.........................................25
Passwords .................................................... 26
Power-on password ..........................................26
Hard-disk password .........................................26
Supervisor password .......................................27
How to remove the hard-disk password ..........27
FRU replacement notices ............................. 36
Screw notices ..................................................36
Retaining serial numbers ..................................37
Removing and replacing an FRU ................. 40
1010 Battery pack .............................................41
1020 Dummy cards...........................................42
1030 Hard disk drive (HDD)/Memory/CPU
(Central processing unit)/Mini PCI ExpressCard
slot compartment cover ...................................43
1040 Hard disk drive ........................................44
1050 Optical drive .............................................46
1060 DIMM .......................................................47
1070 Fan assembly and Heat Sink assembly .....48
1080 CPU .........................................................51
1090 PCI Express Mini Card for wireless
LAN/WAN .........................................................52
1100 Keyboard..................................................54
1110 Keyboard bezel ........................................56
1120 Speakers, power board and touch
inductive panel ..................................................59
1130 System board and ExpressCard slot
assembly ............................................................ 61
1140 LCD unit ...................................................65
1150 Bluetooth daughter card and base cover .....68
1160 LCD front bezel ........................................72
1170 LCD panel and hinges .............................73
1180 Integrated camera ....................................75
1190 Antenna assembly and LCD cover ..........76
Locations ...................................................... 77
Front view .........................................................77
Right-side view .................................................78
Bottom and Left-side view ...............................78
Parts list ........................................................ 79
Overall ..............................................................80
LCD FRUs ........................................................84
Keyboard ..........................................................86
Miscellaneous parts ..........................................88
AC adapters ......................................................89
Power cords ......................................................90
Notices......................................................... 92
Trademarks .................................................. 93
Power management ..................................... 28
Screen blank mode ...........................................28
Sleep (standby) mode ......................................28
Hibernation mode .............................................29
Lenovo G560 ............................................... 30
Specifications ............................................... 30
Status indicators ........................................... 32
FRU tests...................................................... 34
Fn key combinations..................................... 35
iii
About this manual
This manual contains service and reference information for the following
Lenovo product:
Lenovo G560
Use this manual along with the advanced diagnostic tests to troubleshoot
problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety
information required for servicing computers.
• The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with Lenovo
products. Use this manual along with the advanced diagnostic tests to troubleshoot
problems effectively.
Before servicing a Lenovo product, make sure to read all the information under
“Safety information” on page 1 and “Important service information” on page 16.
iv
Safety information
Safety information
This chapter presents the following safety information that you need to get
familiar with before you service a Lenovo G560 computer:
• “General safety” on page 2
• “Electrical safety” on page 3
• “Safety inspection guide” on page 5
• “Handling devices that are sensitive to electrostatic discharge” on page 6
• “Grounding requirements” on page 6
• “Safety notices: multilingual translations” on page 7
• “Laser compliance statement” on page 14
1
Lenovo G560 Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety:
• Observe a good housekeeping in the area where the machines are put
during and after the maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy
for you.
• Do not perform any action that causes hazards to the customer, or that
makes the machine unsafe.
• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
• Place removed covers and other parts in a safe place, keeping them away
from all personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip it
over.
• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.
2
Safety information
Electrical safety
Observe the following rules when working on electrical equipments.
Important:
Use only approved tools and test equipments. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have rubber floor mats near their machines that contain small
conductive fibers to decrease electrostatic discharges. Do not use such kind of mat
to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting the switch
or electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check
it to make sure that it has been powered off.
3
Lenovo G560 Hardware Maintenance Manual
• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.
4
Safety information
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potential
unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards according to the attachment of non-Lenovo features or
options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the
safety of any non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.
5
Lenovo G560 Hardware Maintenance Manual
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your
body.
• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connectoroutside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
6
Safety information
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf
Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse
erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una
FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni
siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.
Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori;
eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio
y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema
y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden
causar cortocircuitos eléctricos.
7
Lenovo G560 Hardware Maintenance Manual
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of an incorrect battery can
result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle
de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de
pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre
feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die
Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht
zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt
werden. Die Batterie kann schwere Verbrennungen oder Verätzungen verursachen.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden,
der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.
Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o
la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo
parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
Safety information
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw
it into fire or water, or short-circuit it. Dispose of the battery pack as required by
local ordinances or regulations. Use only the battery in the appropriate parts listing
when replacing the battery pack. Use of an incorrect battery can result in ignition
or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser
que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste
aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion
führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco
o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego
di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como
dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
9
Lenovo G560 Hardware Maintenance Manual
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as
required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son
connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.
Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile
inappropriée risque de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr
Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung
angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien
des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato,
smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi,
incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria
non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios,
explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado,
ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal como dispone la
normativa local.
10
Safety information
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water at least for 15 minutes.
Seek medical care if any symptoms caused by the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i
sintomi dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus
manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos
como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido
despues de lavarse.
11
Lenovo G560 Hardware Maintenance Manual
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la
mise à la masse d’une batterie peut produire suffisamment de courant pour brûler
des matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada
o con contacto a tierra puede producir la corriente suficiente como para quemar
material combustible o provocar quemaduras en el personal.
12
Safety information
Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez
la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen,
der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi
di interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.
13
Lenovo G560 Hardware Maintenance Manual
Laser compliance statement
Some models of Lenovo computer are equipped from the factory with an
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed,
it is certified in the U.S. to conform to the requirements of the Department of
Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)
Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to
conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles
aqui especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
14
Safety information
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam,
do not view directly with optical instruments, and avoid direct exposure to the
beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe
diretamente por meio de instrumentos óticos e evite exposição direta com o feixe
de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente
in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el
haz de luz. Evite la exposición directa al haz.
15
Lenovo G560 Hardware Maintenance Manual
Important service information
This chapter presents the following important service information:
• “Strategy for replacing FRUs” on page 16
– “Strategy for replacing a hard disk drive” on page 17
– “Important notice for replacing a system board ” on page 17
– “How to use error message” on page 17
• “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 18
– “Product definition” on page 18
– “FRU identification for CTO, CMV, and GAV products” on page 18
• “Important information about replacing RoHS compliant FRUs” on page 20
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site:
http://www.lenovo.com/support.
System Disassembly/Reassembly videos that show the FRU removals or
replacements for the Lenovo® authorized service technicians are available in the
following support site: http://www.lenovoservicetraining.com/ion/.
Advise customers to contact the Customer Support Center at 800-426-7378 if they
need assistance in obtaining or installing any software fixes, drivers, and BIOS
downloads.
Customers in Canada should call the Customer Support Center at 800-565-3344
for assistance or download information.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://www.lenovo.com/support.
2. Enter the product number of the computer or press Auto-detect button on
the screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.
16
Important service information
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
• If you are instructed to replace a FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
• Some computers have both a processor board and a system board. If you
are instructed to replace either of them, and replacing one of them does not
solve the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs
may be the cause of the error. Before replacing the adapter or device,
remove the FRUs one by one to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may
have been customized. Running Automatic Configuration may alter the
settings. Note the current configuration settings (using the View Configuration
option); then, when service has been completed, verify that those settings
remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This
will cause all customer data on the hard disk to be lost. Make sure that the
customer has a current backup of the data before performing this action.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as
copying, saving, or formatting. If you select an incorrect drive, data or programs
can be overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
• Do not drop the system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.
How to use error message
Use the error codes displayed on the screen to diagnose failures. If more
than one error code is displayed, begin the diagnosis with the first error code.
Whatever causes the first error code may also cause false error codes. If
no error code is displayed, see whether the error symptom is listed in the
Symptom-to-FRU Index for the computer you are servicing.
17
Lenovo G560 Hardware Maintenance Manual
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure an IBM® or a Lenovo
solution from an eSite, and have this configuration sent to fulfillment, where
it is built and shipped directly to the customer. The machine label, Product
Entitlement Warehouse (PEW), eSupport, and the HMM will load these
products as the 4-digit MT and 3-digit model, where model = “CTO” (Example:
1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between IBM or
Lenovo and the customer. A unique 4-digit MT and 3-digit model is provided
to the customer to place orders (Example: 1829-W15). A CMV is a special bid
offering. Therefore, it is NOT generally announced.
• The MTM portion of the machine label is the 4-digit MT and 3-digit model,
where model = “CTO” (Example: 1829-CTO). The PRODUCT ID portion of
the machine label is the 4-digit MT and 3-digit CMV model (Example: 1829W15).
• The PEW record is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO).
• eSupport will show both the CTO and CMV machine type models (Example:
1829-CTO and 1829-W15 will be found on the eSupport site).
• The HMM will have the 4-digit MT and 3-digit CTO model only (Example:
1829-CTO). Again, CMVs are custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and
offered to all customers. The MTM portion of the machine label is a 4-digit MT
and 3-digit model, where model = a “fixed part number”, not “CTO” (Example:
1829-F1U). Also, PEW, eSupport, and the HMM will list these products under
the same fixed model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to
support CTO, CMV, and GAV products. These sources are PEW, eSupport,
and the HMM.
Using PEW
• PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CTO, CMV and GAV products at
a MT - serial number level. An example of key commodities are hard disk
drives, system boards, microprocessors, Liquid Crystal Displays (LCDs),
and memory.
• Remember, all CTO and CMV products are loaded in PEW under the 4-digit
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs
are loaded in PEW under the 4-digit MT and 3-digit model, where model = a
“fixed part number”, not “CTO” (Example: 1829-F1U).
• PEW can be accessed at the following Web site:
http://w3-01.ibm.com/pc/entitle/pg2/Service.wss/display/Home.
18
Important service information
Customers can also access PEW via
http://www-307.ibm.com/pc/support/site.wss/product.do?template=/
warranty/warranty.vm&sitestyle=lenovo.
Select Warranty lookup. Input the MT and the Serial number and the list of
key commodities will be returned in the PEW record under COMPONENT
INFORMATION.
• Business Partners using Eclaim will access PEW when performing
Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and
the key commodities will be returned in the Eclaim record under SYSTEM
DETAILS.
• Authorized IBM Business Partners can access Eclaim at the following Web
site: https://wca.eclaim.com.
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
• eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
• eSupport can be accessed at the following Web site:
http://www.lenovo.com/support.
• To view the key commodities, click on PARTS INFORMATION, then PARTS
LOOKUP. Enter the model type and serial number. The key commodities will
be returned in the eSupport record under PARTS SHIPPED WITH YOUR
SYSTEM.
For the Remaining FRUs (the complete list of FRUs at the MT Model level)
• Support can be used to view the complete list of FRUs for a machine type
and model.
• To view the complete list of FRUs, Enter the machine type and model
(Example: 1829-CTO) under QUICK PATH. Select PARTS INFORMATION
under “View by Document Type”. Select SERVICE PARTS under “Filter by
Category”. Select SYSTEM SERVICE PARTS under “Parts Information by
Date”. The list of service parts by description, with applicable machine type
model and FRU will be displayed.
Using the HMM
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRUs at the MT Model level.
19
Lenovo G560 Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after
June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function
are identified with unique FRU part numbers.
Lenovo plans to transit to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements
and schedule in the EU. Products sold in 2005 and 2006 will contain some
RoHS compliant FRUs. The following statement pertains to these products and
any product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the
RoHS implementation date, failed RoHS compliant parts must always be
replaced with RoHS compliant ones, so only the FRUs identified as compliant
in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or
original part
Replacement FRU Current or
original part
Non-RoHS
Can be Non-RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Must be RoHS
Replacement FRU
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
20
General checkout
General checkout
This chapter presents the following information:
• “What to do first” on page 22
• “Power system checkout” on page 23
Before you go to the checkout, make sure to read the following important notes:
Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and replacing
FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace a FRU only with another FRU of the correct model. When you
replace a FRU, make sure that the machine model and the FRU part number are
correct by referring to the FRU parts list.
• A FRU should not be replaced just because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with a
hardware defect, such as cosmic radiation, electrostatic discharge, or software
errors. Consider replacing a FRU only when a problem recurs. If you suspect that
a FRU is defective, clear the error logs and run the test again. If the error does not
recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
21
Lenovo G560 Hardware Maintenance Manual
What to do first
When you do return a FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer’s name and address
Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was
subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken
by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
• Improper disk insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover,
foreign material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.
22
General checkout
Power system checkout
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
• “Checking the AC adapter ” on page 23
• “Checking operational charging” on page 23
• “Checking the battery pack ” on page 24
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:
3
2
(20V)
Pin
Voltage (V DC)
1
+19
2
0
3
Ground
1
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem continues, go to “Lenovo G560” on page 30.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.
23
Lenovo G560 Hardware Maintenance Manual
Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.
If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95%
of the total power remains; under this condition the battery pack can charge to
100% of its capacity. This protects the battery pack from being overcharged or
from having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon
tray of the Windows® taskbar and wait for a moment (but do not click it), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to be charged.
Remove it from the computer and leave it at room temperature for a while. After
it cools down, reinstall and recharge it.
To check the battery pack, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack and measure the voltage between battery
terminals 1 (+) and 7 (-). See the following figure:
1(+)
2(+)
5
3 4
6(-)
7(-)
Terminal
Voltage (V DC)
1
+0 to +12.6
7
Ground (-)
3. If the voltage is less than +11.0 V DC, the battery pack has been
discharged.
Note: Recharging will be continued for at least 3 hours, even though the
indicator does not light on.
If the voltage is still less than +11.0 V DC after recharging, replace the
battery.
4. If the voltage is more than +11.0 V DC, measure the resistance between
battery terminals 5 and 7. The resistance must be 4 to 30 KΩ.
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
24
Related service information
Related service information
This chapter presents the following information:
• “Restoring the factory contents by using OneKey Recovery” on page 25
• “Passwords” on page 26
• “Power management” on page 28
• “Symptom-to-FRU index” on page 32
Service Web site:
When the latest maintenance diskette and the system program service diskette
become available, they will be posted on: http://www.lenovo.com/spm.
Restoring the factory contents by using OneKey Recovery
Restore of factory default
The Lenovo G560 computers come with pre-installed OneKey Rescue System.
In order to save application files and the initial backed up files of the system,
the hard disk in a Lenovo computer includes a hidden partition when it is
shipped. If you need to restore the system to the point of your first boot up, just
enter Lenovo OneKey Rescue System and run Restore to factory default. For
details of OneKey Rescue System, see the User Guide for OneKey Rescue System.
Note: This will delete all the new data on the system partition (C drive), which
is not recoverable. Make sure to back up your critical data before you perform this
action.
Using recovery disks
When you replace a hard disk drive in your computer, you are unable to use
the pre-installed Lenovo OneKey Recovery and OneKey Rescue. However, you
can use the recovery disks that store your backed up data to restore your new
hard drive to a previous backup status.
Note: You can create recovery disks by burning the backup image to a CD/DVD
as recovery disks. For details of Create recovery disks, see the User Guide for
OneKey Rescue System.
25
Lenovo G560 Hardware Maintenance Manual
When you use the recovery disks to boot your computer, the system will enter
the user interface for system recovery automatically. Please follow the prompt
to insert the backup disks to complete the whole recovery process.
Note: The recovery process might take up to 2 hours.
Passwords
As many as three passwords may be needed for any Lenovo computer: the
power-on password (POP), the hard-disk password (HDP), and the supervisor
password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear
when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by
an unauthorized person. The password must be entered before an operating
system can be booted.
Hard-disk password
There are two hard-disk passwords (HDPs):
• User HDP— for the user
• Master HDP— for the system administrator, who can use it to get access to
the hard disk even if the user has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The
Master + User mode requires two HDPs; the system administrator enters both
in the same operation. The system administrator then provides the user HDP to
the system user.
Attention: If the user HDP has been forgotten, check whether a master HDP
has been set. If it has, it can be used for access to the hard disk drive. If no
master HDP is available, neither Lenovo nor Lenovo authorized servicers
provide any services to reset either the user or the master HDP, or to recover
data from the hard disk drive. The hard disk drive can be replaced for a
scheduled fee.
26
Related service information
Supervisor password
A supervisor password (SVP) protects the system information stored in the
BIOS Setup Utility. The user must enter the SVP in order to get access to the
BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to
the servicer, there is no service procedure to reset the password. The system
board must be replaced for a scheduled fee.
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten
and cannot be made available to the servicer, neither Lenovo nor Lenovo
authorized servicers provide any services to reset the user HDPs or to recover
data from the hard disk drive. The hard disk drive can be replaced for a
scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master
HDP are known, follow the steps below:
1. Turn on the computer; while the initial screen is displayed, press F2; then
the BIOS Setup Utility screen opens.
2. Select Security, using the cursor directional keys to move down the menu.
3. Select Password.
4. Select Hard-disk x password, where x is the letter of the hard disk drive. A
pop-up window opens.
5. Select Master HDP.
6. Type the current master HDP in the Enter Current Password field. Then
leave the Enter New Password field blank, and press Enter twice.
7. Press F10.
8. Select Yes in the Setup Configuration window. Both user HDP and master
HDP will have been removed.
27
Lenovo G560 Hardware Maintenance Manual
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management
modes: screen blank, sleep (standby), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off. You can also turn off the LCD backlight by pressing
Fn+F2.
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep (standby) mode, press Fn+F1.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
• If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
• If the battery indicator is amber, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected
in the “Power Management Properties” window, the computer goes into
hibernation mode.)
To cause the computer to return from sleep (standby) mode and resume the
operation, do one of the following:
• Press the Fn key.
• Open the lid.
• Turn on the power switch.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes the operation:
• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters
sleep (standby) mode. Wait a few seconds before taking any action to reenter
operation mode.
28
Related service information
Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk.
• The system is powered off.
To cause the computer to enter hibernation mode, follow the steps below:
• If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action:
– Closing the lid.
– Pressing the power button.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
• If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the hard disk drive, the parallel connector,
or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive
is read, and system status is restored from the hard disk drive.
29
Lenovo G560 Hardware Maintenance Manual
Lenovo G560
This chapter presents the following product-specific service references and
product-specific parts information:
• “Specifications” on page 30
• “Status indicators” on page 32
• “FRU tests” on page 34
• “Fn key combinations” on page 35
• “FRU replacement notices” on page 36
• “Removing and replacing an FRU” on page 40
• “Locations” on page 77
• “Parts list” on page 79
Specifications
The following table lists the specifications of the Lenovo G560 :
Table 1. Specifications
Feature
Description
Processor
•
•
•
•
•
•
•
•
•
•
•
•
Core Chipset
Bus architecture
Graphic memory
chip
Display
Standard
memory
CMOS RAM
Hard disk drive
Optical drive
30
•
•
•
•
•
•
•
•
•
•
•
•
Intel Core i5-520M (2.40GHz, 3MB L3, DDR3-1066, PGA)
Intel Core i5-430M (2.26GHz, 3MB L3, DDR3-1066, PGA)
Intel Core i3-350M (2.26GHz, 3MB L3, DDR3-1066, PGA)
Intel Core i3-330M (2.13GHz, 3MB L3, DDR3-1066, PGA)
Intel HM55
DDR2 SDRAM 800MHZ
HT (HyperTransport™ Interface)
ALINK (A-Link Express II Interface)
PCI Express® Interface
Intel HM55 Intergrated
nvidia N11M-GE1 with 512M DDR3 VRAM
15.6-Inch, 16M colors, HD(1366 × 768 Resolution), 16:9,
WLED type, TFT color LCD
1 × 1GB (DDR3 1066MHz)
2 × 1GB (DDR3 1066MHz)
1 × 1GB + 1 × 2GB (DDR3 1066MHz)
2 × 2GB (DDR3 1066MHz)
1 × 4GB (DDR3 1066MHz)
1 × 2GB + 1 × 4GB (DDR3 1066MHz)
2 × 4GB (DDR3 1066MHz)
512 bytes
160GB, 5400rpm, 9.5 mm high, SATA interface
250GB, 5400rpm, 9.5 mm high, SATA interface
320GB, 5400rpm, 9.5 mm high, SATA interface
500GB, 5400rpm, 9.5 mm high, SATA interface
Supported hard disk drives depend on the model.
• 12.7mm SATA, Fixed Bay
• CDRW/DVD-ROM Rambo
Lenovo G560
Table 1. Specifications (continued)
Feature
Description
I/O port
•
•
•
•
•
•
•
•
•
•
•
•
•
•
MODEM slot
Audio
Video
Ethernet (on the
system board)
PCI Express
Mini Card slot
ExpressCard
slot
Bluetooth
wireless
Keyboard
Touch pad
Integrated
camera
Battery
AC adapter
Pre-installed
operating
system
External monitor connector
Stereo headphone jack
Microphone jack
RJ45 x 1 (on planar)
HDMI port (selected models only)
USB2.0 x 3 (on planar)
E-SATA + USB combo × 1 (on planar)
Express Card slot (selected models only)
5-in-1 media card reader (selected models only)
N/A
1/8" Stereo Headphone Output Jack/ SPIDIF
1/8" Microphone Input Jack
Built-in stereo speakers
CRT port x 1 (on planar), HDMI port x 1 (on planar)
• 10/100 Mb, Giga lan co-lay (selected models only)
• one half size for WLAN card
• one full size for WWAN card
• 34mm width x 1
• Built-in antenna with min-USB interface, selected Models
• 6 Row, ISO Full Size Keyboard
• numeric keypad for 15.6"
• One-piece touchpad
• 0.3M/1.3M mega with LED indicator (selected models only)
•
•
•
•
•
•
•
Li-ion battery (6 cells) 2200 mAh
Li-ion battery (6 cells) 2600 mAh
65 W/20 V
Windows 7 Home Basic/Premium/Professional (32 bit/64 bit)
Windows Vista basic (32 bit/64 bit)
Windows XP Pro (downgrade)
DOS
31
Lenovo G560 Hardware Maintenance Manual
Status indicators
The system status indicators below show the computer status:
1
2
3
4
5
6
Table 2. Status indicators
Indicator
32
1
Caps lock
2
Num lock
3
Power on
Meaning
White:
Caps Lock mode is enabled. You can enter all
alphabetic characters (A-Z) in uppercase without
pressing the Shift key. To enable or disable Caps
Lock mode, press the CapsLk key.
White:
The separate numeric keypad on the keyboard is
enabled. To enable or disable the numeric keypad,
press the Num Lock key.
White:
System is enabled.
Blinking white:
System is in sleep mode.
Off:
System is in hibernate mode or shut down.
Lenovo G560
Table 2. Status indicators (continued)
Indicator
4
Battery status
5
Wireless
status
6
Drive in use
Meaning
Blinking amber (500ms off/1s on):
The remaining power of the battery is less than 5%
of its capacity.
Blinking amber (100ms off/3.2s on):
The battery is being charged with the remaining
power between 5% and 20% of its capacity.
Amber:
The computer is operating on battery power with
the remaining power between 5% and 20% of its
capacity.
Blinking white:
The battery is being charged with the remaining
power between 20% and 80% of its capacity.
White:
The remaining power of the battery is more than
80% of its capacity, or the computer is operating on
battery power with the remaining power between
20% and 80% of its capacity.
White:
Any one of the wireless devices (WLAN/Bluetooth/
WWAN) is enabled.
Off:
All the wireless devices (WLAN/Bluetooth/WWAN)
are disabled.
White:
Data is being read from or written to the hard disk
drive or the optical disk drive. When this indicator
is on, do not put the computer into standby mode
or turn off the computer.
Note: Do not move the system while the white drive-in-use
light is on. Sudden physical shock could cause drive errors.
33
Lenovo G560 Hardware Maintenance Manual
FRU tests
The following table shows the test for each FRU.
Table 3. FRU tests
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
1. Diagnostics --> Systemboard --> Keyboard
2. Interactive Tests --> Keyboard
Diagnostics --> Fixed Disks
Diagnostics --> Diskette Drives
1. If two DIMMs are installed, remove one of them and run
Diagnostics --> PM Memory.
2. If the problem does not recur, return the DIMM to its
place, remove the other one, and run the test again.
3. If the test does not detect the error, run Diagnostics -->
PM Memory.
LCD unit
Keyboard
Hard disk drive
Diskette drive
Memory
34
Lenovo G560
Fn key combinations
The following table shows the function of each combination of Fn with a
function key.
Table 4. Fn key combinations
Key combination
Description
Fn + Esc:
Fn + F1:
Fn + F2:
Turn on/off the integrated camera.
Enter sleep mode.
Turn on/off the backlight of the LCD screen.
Open the interface for the display device switch to select
this notebook or an external display.
Open the interface for display resolution settings.
Open the interface for integrated wireless devices settings
(on/off).
Enable/Disable the touchpad.
Start/Pause playback of Windows Media Player.
Stop playback of Windows Media Player.
Skip to the previous track.
Skip to the next track.
Enable/Disable the scroll lock.
Activate the system request.
Activate the pause function.
Activate the break function.
Increase/Decrease display brightness.
Increase/Decrease sound volume.
Fn + F3:
Fn + F4:
Fn + F5:
Fn + F6:
Fn + F9:
Fn + F10:
Fn + F11:
Fn + F12:
Fn + Insert:
Fn + PrtSc:
Fn + Home:
Fn + End:
Fn + / :
Fn + / :
35
Lenovo G560 Hardware Maintenance Manual
FRU replacement notices
This section presents notices related to removing and replacing parts. Read
this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
• Each one should be used only once.
Do the following when you service this machine:
• Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 88) in
your tool bag.
• Always use new screws.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the
plastic part:
more than 90°
(Cross-section)
• Logic card to plastic
Turn an additional 180° after the screw head touches the surface of the
logic card:
more than 180°
(Cross-section)
• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a
screw that you removed. Use a new one. Make sure that all screws are
tightened firmly.
• Ensure torque screwdrivers are calibrated correctly following country
specifications.
36
Lenovo G560
Retaining serial numbers
This section presents the following descriptions:
• “Restoring the serial number of the system unit” on page 37
• “Retaining the UUID” on page 38
• “Reading or writing the ECA information ” on page 39
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was
loaded with the serial numbers of the system and all major components. These
numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the
system unit to its original value.
Before replacing the system board, save the original serial number by doing the
following:
1. Install the CE Utility Diskette for Lenovo notebooks, and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial
number of the system unit is listed as follows:
• 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached
to the bottom of the computer.
After you have replaced the system board, restore the serial number by doing
the following:
1. Install the CE Utility Diskette for Lenovo notebooks and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM.
Follow the instructions on the screen.
If the MTM and Product ID numbers differ from each other on the rear label,
apply what is shown for the Product ID field. See the following example:
MTM on rear label:
TTTT-CTO S/N SSSSSSS
Product ID on rear label:
TTTT-MMM (apply this number when setting Serial Number)
In the example, the Serial Number to be applied is ‘1STTTTMMMSSSSSSS’.
37
Lenovo G560 Hardware Maintenance Manual
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned
to your computer at its production and stored in the EEPROM of your system
board. The algorithm that generates the number is designed to provide unique
IDs until the year A.D. 3400. No two computers in the world have the same
number.
When you replace the system board, you must set the UUID on the new
system board as follows:
1. Install the CE Utility Diskette for Lenovo notebooks, and restart the
computer.
2. From the main menu, select 4. Assign UUID.
A new UUID is created and written. If a valid UUID already exists, it is not
overwritten.
38
Lenovo G560
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in
the EEPROM of the system board. The electronic storage of this information
simplifies the procedure to check if the ECA has been previously applied to a
machine. The machine does not need to be disassembled to check for the ECA
application.
To check what ECAs have been previously applied to the machine, enable
the ECA Information Read/Write function on the CE Utility Diskette for Lenovo
notebooks.
1. Insert the CE Utility Diskette for Lenovo notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from
EEPROM and follow the instructions.
4. To read box build date, select 5. Read box build date from EEPROM, and
follow the instructions on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated
to reflect the ECA’s application. Apply the CE Utility Diskette for Lenovo
notebooks to update the EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of
the ECA is assumed as the same as that of the machine which had the ECA
applied to it.
1. Insert the CE Utility Diskette for Lenovo notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from
EEPROM, and follow the instructions.
4. To write box build date, select 4. Write box build date from EEPROM, and
follow the instructions on the screen.
If the system board is being replaced, try to read the ECA information from the
old system board and transfer the information to the new system. If the system
board is inoperable, this will not be possible.
39
Lenovo G560 Hardware Maintenance Manual
Removing and replacing an FRU
This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 36
3. Begin by removing any FRUs that have to be removed before the failing
FRU. Any of such FRUs are listed at the top of the page. Remove them in
the order in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in
the figure.
7. To put the new FRU in place, reverse the removal procedures and follow
any of the notes that pertain to replacement. For information about
connecting and arranging internal cables, see “Locations” on page 77.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any of the
interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by,
electrostatic discharge. Before touching it, establish personal grounding by
touching a ground point with one hand or using an electrostatic discharge (ESD)
strap (P/N 6405959) to remove potential shock reasons.
40
Lenovo G560
1010 Battery pack
DANGER
Only use the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Figure 1. Removal steps of battery pack
Unlock the battery release lever 1. Holding the battery release lever in the
unlocked position 2, remove the battery pack in the direction shown by arrow
3.
1
1
3
2
2
When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is in the locked position.
41
Lenovo G560 Hardware Maintenance Manual
1020 Dummy cards
For access, remove this FRU:
• “1010 Battery pack” on page 41
Figure 2. Removal steps of dummy cards
Remove two dummy cards in the direction shown by arrows 1 2.
1
2
1
2
42
Lenovo G560
1030 Hard disk drive (HDD)/Memory/CPU (Central processing
unit)/Mini PCI ExpressCard slot compartment cover
For access, remove this FRU:
• “1010 Battery pack” on page 41
Figure 3. Removal steps of HDD/Memory/CPU/Mini PCI ExpressCard slot
compartment cover
Note: Loosen the screws 1, but do not remove them. Remove two screws 2.
Remove the HDD/Memory/CPU/Mini PCI ExpressCard slot compartment cover
in the direction shown by arrow 3.
1
1
1
2
1
2
1
3
Step
2
Screw (quantity)
Color
Torque
M2.5 × 8 mm, flat-head, nylon-coated (2)
Black
0.6 Nm
(6 kgfcm)
43
Lenovo G560 Hardware Maintenance Manual
1040 Hard disk drive
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
Attention:
• Do not drop the hard disk drive or apply any physical shock to it. The hard
disk drive is sensitive to physical shock. Improper handling can cause damages
and permanent loss of data.
• Before removing the drive, suggest the customer to backup all the information on
it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Figure 4. Removal steps of Hard disk drive
Remove two screws 1. Pull the tab up in the direction shown by arrows
to remove the hard disk drive from the slot.
1
1
2
44
23
Lenovo G560
3
Step
1
Screw (quantity)
Color
Torque
M2.0 × 6 mm, flat-head, nylon-coated (2)
Black
0.6 Nm
(6 kgfcm)
When installing: Make sure that the HDD connector is attached firmly.
45
Lenovo G560 Hardware Maintenance Manual
1050 Optical drive
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini PCI
ExpressCard slot compartment cover ” on page 43
Figure 5. Removal steps of optical drive
Remove the screw 1, insert a screwdriver into the screw hole and push the
optical drive in the direction shown by arrow 2, and then pull the optical drive
out in the direction shown by arrow 3.
1
Step
1
Screw (quantity)
Color
Torque
M2.5 × 4 mm, flat-head, nylon-coated (1)
Black
0.6 Nm
(6 kgfcm)
2
3
46
Lenovo G560
1060 DIMM
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
Figure 6. Removal steps of DIMM
Release the two latches on both edges of the socket at the same time in the
direction shown by arrows 1, and then unplug the DIMM in the direction shown
by arrow 2.
1
2
1
Note: If only one DIMM is used on the computer you are servicing, the card
must be installed in SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper
slot).
b
a
When installing: Insert the notched end of the DIMM into the socket. Push the
DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly
fixed in the slot and difficult to be moved.
47
Lenovo G560 Hardware Maintenance Manual
1070 Fan assembly and Heat Sink assembly
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
Figure 7. Removal steps of fan assembly and heat sink assembly
Note: Remove three screws 1 and four spring screws 2.
Unplug the connector in the direction shown by arrow 3.
1
1
2
2
2
3
2
1
When installing: Make sure that the fan connector is attached firmly to the
system board.
Step
48
Screw (quantity)
Color
Torque
1
M2.5 × 4 mm, flat-head, nylon-coated (3)
Black
2
M2.0 × 3.2 mm, with spring, nylon-coated (4) Silver
0.6 Nm
(6 kgfcm)
2.0~2.5 Nm
(2.0~2.5 kgfcm)
Lenovo G560
Figure 7. Removal steps of fan assembly and heat sink assembly (continued)
Lift the fan assembly and heat sink assembly in the direction shown by arrow 4.
Be careful not to damage the connector.
4
Attention: Do not handle the heat sink assembly roughly. Improper handling
can cause distortion or deformation and imperfect contact with components.
Figure 7. Removal steps of fan assembly and heat sink assembly (continued)
49
Lenovo G560 Hardware Maintenance Manual
a
b
When installing:
• Before you attach the fan assembly to the computer, apply thermal grease,
at an amount of 0.2 grams, to the a b part shown in the figure above. Either
too much or too less grease application can cause a thermal problem due to
imperfect contact with a component.
50
Lenovo G560
1080 CPU
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1070 Fan assembly and Heat Sink assembly” on page 48
Attention: CPU is extremely sensitive. When you service the CPU, avoid any
kind of rough handling.
Figure 8. Removal steps of CPU
Rotate the head of the screw in the direction shown by arrow 1 to release the
lock, then remove the CPU in the direction shown by arrow 2.
1
a
b
2
When installing: Place the CPU on the CPU socket in the direction shown by
arrow a , and then rotate the head of the screw in the direction shown by arrow
b to secure the CPU.
51
Lenovo G560 Hardware Maintenance Manual
1090 PCI Express Mini Card for wireless LAN/WAN
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
Figure 9. Removal steps of PCI Express Mini Card for wireless LAN/WAN
1
1
2
2
Disconnect the two wireless LAN cables (black, white) and the two wireless
WAN cables (red, blue) in the direction shown by arrows 1, and then remove
the screws 2.
Step
2
Screw (quantity)
Color
Torque
M2.0 × 3 mm, flat-head, nylon-coated (2)
Black
0.4 Nm
(4 kgfcm)
In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug
them in the direction shown by arrows.
52
Lenovo G560
Notes: wireless LAN card has 2 cables in step 1.
wireless LAN card in some models may have 3 cables in step 1.
wireless WAN card has 2 cables in step 1.
Figure 9. Removal steps of PCI Express Mini Card for wireless LAN/WAN
(continued)
Remove two cards in the direction shown by arrows 3.
3
3
When installing:
• In models with a wireless LAN card that has two antenna connectors, plug
the black cable into the jack labeled 1, and the white cable into the jack
labeled 2 on the card.
• In models with a wireless WAN card that has two antenna connectors, plug
the red cable into the jack labeled MAIN, and the blue cable into the jack
labeled AUX on the card.
53
Lenovo G560 Hardware Maintenance Manual
1100 Keyboard
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
Figure 10. Removal steps of keyboard
Remove the screws 1, 2 on the bottom.
1
1
Step
54
2
Screw (quantity)
Color
Torque
1
M2.5 × 8 mm, flat-head, nylon-coated (2)
Black
2
M2.0 × 3 mm, flat-head, nylon-coated (1)
Black
0.6 Nm
(6 kgfcm)
0.25 Nm
(2.5 kgfcm)
Lenovo G560
Figure 10. Removal steps of keyboard (continued)
Lift the keyboard a little 3, unlock the FPC connector and then detach the
connector in the direction shown by arrows 4 5.
3
5
4
When installing: Make sure that the FPC connector is attached firmly and then
lock the FPC connector.
55
Lenovo G560 Hardware Maintenance Manual
1110 Keyboard bezel
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1100 Keyboard” on page 54
Figure 11. Removal steps of keyboard bezel
Remove four screws 1, two screws 2 and eleven screws 3 on the bottom.
2
3
3
1
3
1
3
1
3
2
1
3
3
3
3
3
3
Step
56
Screw (quantity)
Color
Torque
1
M2.0 × 2 mm, flat-head, nylon-coated (4)
Black
2
M2.5 × 10 mm, flat-head, nylon-coated (2)
Black
3
M2.5 × 8 mm, flat-head, nylon-coated (11)
Black
0.25 Nm
(2.5 kgfcm)
0.6 Nm
(6 kgfcm)
0.6 Nm
(6 kgfcm)
Lenovo G560
Figure 11. Removal steps of keyboard bezel (continued)
Remove one screw 4 and detach three FPC connectors in the direction shown
by arrows 5 6.
6
4
6
5
5
Step
4
Screw (quantity)
Color
Torque
M2.5 × 4 mm, flat-head, nylon-coated (1)
Black
0.6 Nm
(6 kgfcm)
When installing: Make sure that all the FPC connectors are attached firmly.
57
Lenovo G560 Hardware Maintenance Manual
Figure 11. Removal steps of keyboard bezel (continued)
Lift the keyboard bezel a little, detach the speaker connector in the direction
shown by arrows 7, and then remove the keyboard bezel 8.
7
8
When installing: Make sure that the speaker connector is attached firmly.
58
Lenovo G560
1120 Speakers, power board and touch inductive panel
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
Figure 12. Removal steps of speakers, power board and touch inductive panel
Turn over the keyboard bezel, remove four screws 1, release the speaker
cables from the cable guides, and then remove the speakers.
1
1
1
Step
1
1
Screw (quantity)
Color
Torque
M2.5 × 5.7 mm, flat-head, nylon-coated (4)
Black
0.6 Nm
(6 kgfcm)
59
Lenovo G560 Hardware Maintenance Manual
Figure 12. Removal steps of speakers, power board and touch inductive panel
(continued)
Remove two screws 2 and remove the power board 3.
2
2
3
Notes: The touch inductive panel is fixed on the keyboard bezel.
Step
2
60
Screw (quantity)
Color
Torque
M2.0 × 3 mm, flat-head, nylon-coated (2)
Black
0.25 Nm
(2.5 kgfcm)
Lenovo G560
1130 System board and ExpressCard slot assembly
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• Be careful not to drop the system board on a bench top that has a hard surface,
such as metal, wood, or composite.
• Avoid rough handling of any kind.
• In the whole process, make sure not to drop or stack the system board.
• If you put a system board down, make sure to put it only on a padded surface such
as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
Note: ExpressCard slot assembly is attached to the system board.
Figure 13. Removal steps of system board and ExpressCard slot assembly
Unplug the LCD connector and detach two connectors in the direction shown by
arrows 1.
1
1
When installing: Make sure that the connectors are attached firmly.
61
Lenovo G560 Hardware Maintenance Manual
Figure 13. Removal steps of system board and ExpressCard slot assembly
(continued)
Remove four screws 2 and detach a connector in the direction shown by arrow 3.
2
2
2
2
3
When installing: Make sure that the connector is attached firmly.
Step
2
62
Screw (quantity)
Color
Torque
M2.5 × 4 mm, flat-head, nylon-coated (4)
Black
0.6 Nm
(6 kgfcm)
Lenovo G560
Figure 13. Removal steps of system board and ExpressCard slot assembly
(continued)
Remove the system board in the direction shown by arrow 4.
4
a
a
b
When installing: When attaching the system board to the base cover, adjust
the placement of the wireless radio switch as shown in b , and make sure that
both of the audio jack and the microphone jack are attached to the holes on the
base cover as shown in a . Improper placement of the switch or those jacks
might cause a damage.
63
Lenovo G560 Hardware Maintenance Manual
Figure 13. Removal steps of system board and ExpressCard slot assembly
(continued)
Turn the system board over and remove two screws 5.
4
Step
5
4
Screw (quantity)
Color
Torque
M2.0 × 3 mm, flat-head, nylon-coated (2)
Black
0.25 Nm
(2.5 kgfcm)
Remove the ExpressCard slot assembly in the direction shown by arrow 6.
6
64
Lenovo G560
1140 LCD unit
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
Figure 14. Removal steps of LCD unit
Pull out the four antenna cables from the guide hole in the direction shown by
arrows 1 and release them from the cable guides in the direction shown by
arrows 2.
1
1
65
Lenovo G560 Hardware Maintenance Manual
2
2
2
2
When installing:
• Route the antenna cables along the cable guides. As you route the cables,
make sure that they are not subjected to any tension. Tension could cause
the cables to be damaged by the cable guides, or a wire to be broken.
66
Lenovo G560
Figure 14. Removal steps of LCD unit (continued)
Remove four screws 3.
3
3
3
Step
3
3
Screw (quantity)
Color
Torque
M2.5 × 4 mm, flat-head, nylon-coated (4)
Black
0.6 Nm
(6 kgfcm)
Remove the LCD unit in the direction shown by arrows 4.
4
4
67
Lenovo G560 Hardware Maintenance Manual
1150 Bluetooth daughter card and base cover
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
Figure 15. Removal steps of bluetooth daughter card and base cover
The Bluetooth daughter card is attached to the base cover. Remove the
Bluetooth daughter card in the direction shown by arrows 1.
1
1
When installing: Make sure that the connector is attached firmly.
68
Lenovo G560
Figure 15. Removal steps of bluetooth daughter card and base cover (continued)
Remove the power assembly in the direction shown by arrows 2.
2
2
When installing: Make sure that the power connector is attached firmly.
Remove one screw
shown by arrow 4.
3 and then remove the USB assembly in the direction
3
4
When installing: Make sure that the USB connector is attached firmly.
Step
3
Screw (quantity)
Color
Torque
M2.0 × 3 mm, flat-head, nylon-coated (1)
Black
0.25 Nm
(2.5 kgfcm)
69
Lenovo G560 Hardware Maintenance Manual
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
label:
The following labels need to be peeled off from the old base cover, and need
to be put on the new base cover.
For models in China:
a
PRC CODE label
b
ENERGY label
c
Windows license label (COA)
d
Rating label
For the location of each label, refer to the following figure:
1
b
a
c
d
For models in Japan:
a
MTM CODE label
b
Windows license label (COA)
c
Rating label
For the location of each label, refer to the following figure:
1
a
b
c
Note: The MTM label is only for the models in the following countries: Japan,
Korea, Brazil, Argentina, Chile, Colombia, Peru, Venezuela, Bolivia, Uruguay,
Paraguay, and Ecuador Model (or LA group Model , GEO code LM)
70
Lenovo G560
For models in other countries or regions:
a
b
c
d
Bluetooth label
WLAN label
Windows license label (COA)
Rating label
For the location of each label, refer to the following figure:
1
a
b
c
d
For some models, you also need to apply one or two FCC labels. Check the
old base cover; if it has one or two FCC labels, find duplicates of them in the
label kit and apply them to the new base cover.
71
Lenovo G560 Hardware Maintenance Manual
1160 LCD front bezel
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
• “1140 LCD unit” on page 65
Figure 16. Removal steps of LCD front bezel
Remove six screws 1.
Step
1
Screw (quantity)
Color
Torque
M2.5 × 5 mm, flat-head, nylon-coated (6)
Silver
0.6 Nm
(6 kgfcm)
Remove the LCD front bezel in the direction shown by arrows 2.
2
2
2
72
2
Lenovo G560
1170 LCD panel and hinges
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
• “1140 LCD unit” on page 65
• “1160 LCD front bezel” on page 72
Figure 17. Removal steps of LCD panel and hinges
Remove two screws 1, and then release the LCD panel.
1
1
Step
1
Screw (quantity)
Color
Torque
M2.5 × 5 mm, flat-head, nylon-coated (2)
Silver
0.6 Nm
(6 kgfcm)
73
Lenovo G560 Hardware Maintenance Manual
Figure 17. Removal steps of LCD panel and hinges (continued)
Lift the LCD panel a little and detach the connector on the back of the LCD
panel in the direction shown by arrow 2. Remove the LCD panel 3.
Note: The LCD circuit is attached to the LCD panel, and connected with the
LCD cable by an FPC connector.
When installing: Make sure that the connector is attached firmly.
Remove eight screws 4, and release the hinges from the LCD panel in the
direction shown by arrows 5.
4
5
4
4
4
4
4
4
4
Step
4
74
5
Screw (quantity)
Color
Torque
M2.0 × 3 mm, flat-head, nylon-coated (8)
Black
0.25 Nm
(2.5 kgfcm)
Lenovo G560
1180 Integrated camera
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
• “1140 LCD unit” on page 65
• “1160 LCD front bezel” on page 72
• “1170 LCD panel and hinges” on page 73
Figure 18. Removal steps of integrated camera
Note: The integrated camera is stuck on the top center of the LCD cover.
Detach the connector in the direction shown by arrow 1 and then remove the
integrated camera from the LCD cover 2.
1
2
When installing: Stick the integrated camera to the top center of the LCD
cover and ajust the placement of it to make sure the connector is attached
firmly. When replacing the integrated camera, route the connector cable as
shown in the figure above.
75
Lenovo G560 Hardware Maintenance Manual
1190 Antenna assembly and LCD cover
For access, remove these FRUs in order:
• “1010 Battery pack” on page 41
• “1020 Dummy cards” on page 42
• “1030 Hard disk drive (HDD)/Memory/CPU (Central processing unit)/Mini
PCI ExpressCard slot compartment cover ” on page 43
• “1040 Hard disk drive ” on page 44
• “1050 Optical drive” on page 46
• “1060 DIMM” on page 47
• “1070 Fan assembly and Heat Sink assembly” on page 48
• “1090 PCI Express Mini Card for wireless LAN/WAN” on page 52
• “1100 Keyboard” on page 54
• “1110 Keyboard bezel” on page 56
• “1130 System board and ExpressCard slot assembly” on page 61
• “1140 LCD unit” on page 65
• “1160 LCD front bezel” on page 72
• “1170 LCD panel and hinges” on page 73
Figure 19. Removal steps of antenna assembly and LCD cover
Peel off the adhesive tapes securing the antenna boards, release the
cables from the cable guide, and then remove the antenna assembly in the
direction shown by arrows 1.
1
1
When installing: Route the antenna cables along the cable guides and secure
the antenna boards with adhesive tapes. As you route the cables, make sure
that they are not subjected to any tension. Tension could cause the cables to
be damaged by the cable guides, or a wire to be broken.
76
Lenovo G560
Locations
Front view
1
2
3
4
Integrated camera
Array microphones (bulit-in)
Wireless LAN antennas
System status indicators
Note: For the description of each indicator, see “Status indicators” on page 32.
5 Energy Management button (selected models only)
6 OneKey Rescue System button
7 Power button
8 Built-in microphone
9 Integrated wireless device switch
J One-piece touchpad
K Memory card slot (selected models only)
L OneKey Theater (selected models only)
M Volume buttons (selected models only)
3
2
3
1
4
5
6
7
13
8
12
9
4
10
11
77
Lenovo G560 Hardware Maintenance Manual
Right-side view
1
2
3
4
5
Microphone jack
Headphone jack
Optical drive
USB port
AC power adapter jack
5
4
3
2
1
Bottom and Left-side view
1
2
3
4
5
6
7
8
9
0
K
L
HDMI port (selected models only)
ExpressCard®slot (selected models only)
eSATA/USB combo port (selected models only)
USB port
VGA port
RJ-45 port
Fan louvers
Kensington slot
HDD/Memory/CPU/Mini PCI ExpressCard slot compartment
Battery latch - spring loaded
Battery pack
Battery latch - manual
12
11
10
9
8
7
6
5
4
3
2
78
1
Lenovo G560
Parts list
This section presents the following service parts:
• “Overall” on page 80
• “LCD FRUs” on page 84
Notes:
• Each FRU is available for all types or models, unless specific types or models
are specified.
• FRU with specific models listed and described as xxU (where U is an example
of a country designator) should be used for all models ending in U.
• FRU with specific models listed and described as 3Dx (where 3D is an example
of a unique configuration) should be used for all of these models, unless specific
country or region designator is specified.
• A CRU (customer replaceable unit) is identified by a single asterisk (*) or two
asterisks (**) in the CRU ID column. An N in the CRU ID column means that
the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
Lenovo computers contain the following types of CRUs:
Self-service CRUs
These CRUs are unplugged or held by no more than two screws.
Examples of these types of CRUs include an AC adapter, a power
cord, a battery, and a hard disk drive. Other Self-service CRUs
depending on product design may include a memory, a wireless card,
a keyboard, and a palm rest with finger print reader and touchpad.
Optional-service CRUs
These CRUs are isolated parts within the computer that are concealed
by an access panel that is typically secured by more than two screws.
Once the access panel is removed, the specific CRU is visible.
• A RoHS compliant FRU is identified by an R. An N in the RoHS ID column
means the part is not a RoHS compliant FRU.
• FRUs marked with OP are available as options.
79
Lenovo G560 Hardware Maintenance Manual
Overall
1
2
g
4
3
a
5
7
6
9
10
8
11
d
12
e
f
14
13
15
17
80
16
17
18
c
b
20
21
19
Lenovo G560
Table 5. Parts list—Overall
No.
FRU
1
2
3
3
4
5
6
7
7
7
7
7
8
9
LCD unit (see “LCD FRUs” on page 84.)
Keyboard (see “Keyboard” on page 86.)
NIWE2 LOGIC UPPER ASSY 15.6-AL
NIWE2 LOGIC UPPER ASSY 15.6-TEXTURE
NIWE2 POWER BOARD-15.6
NIWE2 SENSOR BOARD-15.6
NIWE2 SPEAKER SET-15.6
NIWE2 MB ASSY GIGA DIS 15.6-FULL F
NIWE2 MB ASSY 10/100 DIS 15.6-FULL F
NIWE2 MB ASSY GIGA UMA-15.6-FULL F
NIWE2 MB ASSY 10/100 UMA 15.6-FULL F
NIWE2 MB ASSY 10/100 UMA-15.6-W/O HDMI
NIWE2 CARD READER-15.6
CPU assembly, Intel ARD 2.66G 4M I7-620M rPGA
processor
CPU assembly, Intel ARD 2.53G 3M I5-540M rPGA
processor
CPU assembly, Intel ARD 2.13G 3M C2 I3-330M PGA
processor
CPU assembly, Intel ARD 2.40G 3M I5-520M rPGA
processor
CPU assembly, Intel ARD 2.26G 4M C2 I5-430M PGA
processor
CPU assembly, Intel ARD 2.26G 3M C2 I3-350M PGA
processor
CPU assembly, Intel Arrandale 2.00GHZ 3MB C-0 PGA
ES2 processor
CPU assembly, Intel Arrandale 1.86GHZ 3MB C-0 PGA
ES2 processor
NIWE1 FAN
NIWE1 THERMAL MODULE-UMA
NIWE1 THERMAL MODULE-DIS
DDRIII 1066 1GB, M471B2873FHS-CF8 (CS: Nov 5 new
30pcs)
DDRIII 1066 1GB, EBJ10UE8BDS0-AE-F (Rev D
/1Gb/65nm)
DDRIII 1066 1GB, MT8JSF12864HZ1G1F1(V58B/1Gb/68nm)
DDRIII 1066 1GB, HMT112S6BFR6C-G7 N0
(Orion/1Gb/54nm)
DDRIII 1066 2GB, M471B5673FH0-CF8 (CS: Nov 5 new
30pcs)
DDRIII 1066 2GB, EBJ21UE8BDS0-AE-F(Rev D
/1Gb/65nm)
DDRIII 1066 2GB, MT16JSF25664HZ-1G1F1
(V58B/1Gb/68nm)
9
9
9
9
9
9
9
10
11
11
12
12
12
12
12
12
12
FRU no.
31042396
31042397
11011870
31042393
31042388
11011886
11011887
11011889
11011890
11011892
11011875
102000791
102000790
102000786
102000789
102000788
102000787
102000709
102000724
31042378
31042382
31042383
11011550
11011281
11010924
11010904
11011551
11011240
11010925
81
Lenovo G560 Hardware Maintenance Manual
Table 5. Parts list—Overall (continued)
No.
FRU
FRU no.
12
DDRIII 1066 2GB, HMT125S6BFR8C-G7 N0
(Orion/1Gb/54nm)
WLAN card, 802.11a/g/n && 802.16e, Intel 6250NX MOW M
PCIE NB HMC
WLAN card, 802.11a/g/n && 802.16e, Intel 6250GX MOW M
PCIE NB HMC
WLAN card, 802.11 a/g/n, Intel 6200N MOW M PCIE NB
HMC
WLAN card, 802.11 b/g/n, Gtc BCM43225 BGN MOW NB
WLAN card, 802.11 b/g/n, Intel 1000N MOW M PCIE NB
HMC
WLAN card, 802.11 b/g/n, Cbt AR9283 HB93 BGN MOW
NB
WLAN card, 802.11 b/g/n, Gtc BCM4313 M 802.11N MOW
NB
WLAN card, 802.11 b/g/n, Cbt AR9285 HB95 BGN MOW
NB
WLAN card, 802.11 b/g/n, Liteon AR9285 HB95 BGN MOW
NB
Bluetooth card, BT2.1 + ED, Fcn BCM92070 BT2.1 EDR
Flash U NB
Bluetooth card, BT2.1 + ED, USI BCM92070 BT2.1 EDR
Flash U NB
Battery pack, 2.2mAh,6 cell, Sanyo 11.1V 3S2P 4400mAh
Li-ion NB battery
Battery pack, 2.2mAh,6 cell, SMP 11.1V 3S2P 4400mAh Liion NB battery
Battery pack, 2.2mAh,6 cell, LG 11.1V 3S2P 4400mAh Liion NB battery
Battery pack, 2.2mAh,6 cell, G460/G560 SMP 2.2Ah 3S2P
Li-ion Battery(B)
NIWE2 LOGIC LOWER 15.6-FULL F
NIWE2 LOGIC LOWER 15.6-WO HDMI
NIWE1 EXPRESS DUMMY CARD
NIWE1 SD DUMMY CARD
HDD/SSD, 160G 5400rpm SATA, Seagate ST9160314AS
160G 9NB
HDD/SSD, 160G 5400rpm SATA, Hitachi
HTS545016B9A300 160G 9NB
HDD/SSD, 160G 5400rpm SATA, Fujitsu MJA2160BH 160G
9NB
HDD/SSD, 250G 5400rpm SATA, WD2500BEVT-22A23T0
5400RPM250G
HDD/SSD, 250G 5400rpm SATA, Hitachi
HTS545025B9A300 250G 9NB
HDD/SSD, 250G 5400rpm SATA, Fujitsu MJA2250BH
250G 9NB
11010905
13
13
13
13
13
13
13
13
13
14
14
15
15
15
15
16
16
17
17
18
18
18
18
18
19
82
20002321
20002388
20002324
20002271
20002329
20002276
20002347
20002346
20002357
TBD
TBD
121000938
121000935
121000937
121000939
31042406
31042407
31042435
31042436
16004187
16004061
16004077
16004524
16004060
16004076
Lenovo G560
Table 5. Parts list—Overall (continued)
No.
FRU
FRU no.
18
HDD/SSD, 250G 5400rpm SATA, Seagate ST9250315AS
250G 9NB
HDD/SSD, 320G 5400rpm SATA, Hitachi
HTS545032B9A300 320G 9NB
HDD/SSD, 320G 5400rpm SATA, Seagate ST9320325AS
320G 9NB
HDD/SSD, 500G 5400rpm SATA, Seagate ST9500325AS
500G 9NB
HDD/SSD, 500G 5400rpm SATA, WD5000BEVT-22A0RT0
5400RPM500G
HDD/SSD, 500G 5400rpm SATA, Hitachi
HTS545050B9A300 500G 9NB
HDD/SSD, 500G 5400rpm SATA, Fujitsu MJA2500BH 500G
9NB
NIWE1 ODD BEZEL-BD
NIWE1 ODD BEZEL-SM
ODD, 12.7mm Tray Rambo, GT30N
ODD, 12.7mm Tray Rambo, AD-7585H(QSI)
ODD, 12.7mm Tray Rambo, DS-8A4S
ODD, 12.7mm Tray Rambo, UJ890A
ODD, 12.7mm Tray BD Combo, BC-5500H
ODD, 12.7mm Tray BD Combo, DS-4E1S
NIWE2 THERMAL DOOR-15.6
AC adapter (see “AC adapters” on page 89.)
16004186
18
18
18
18
18
18
19
19
20
20
20
20
20
20
21
-
16004059
16004183
16004189
16004526
16004058
16004074
31042379
31042380
25009116
25009461
25009439
25009440
25009785
25009829
31042374
83
Lenovo G560 Hardware Maintenance Manual
LCD FRUs
In Lenovo G560, there are following types of LCDs.
• “15.6-in. HD TFT”
84
Lenovo G560
15.6-in. HD TFT
Table 6. Parts list—15.6-in. HD TFT
No.
FRU
FRU no.
1
1
1
2
3
3
3
3
3
4
4
5
6
6
7
7
7
NIWE2 LCD BEZEL 15.6 HTM-W/CAMERA F
NIWE2 LCD BEZEL 15.6 TEXTURE-W/CAMERA F
NIWE2 LCD BEZEL 15.6 TEXTURE-WO CAMERA F
NIWE2 LCD BRACKET 15.6 R+L
LCD panel, 15.6HD, B156XW02 V2
LCD panel, 15.6HD, LP156WH2-TLAA
LCD panel, 15.6HD, LTN156AT05-J01
LCD panel, 15.6HD, HT156WXB-100
LCD panel, 15.6HD, N156B6-L0B
NIWE2 LVDS_COMS CABLE-15.6
NIWE2 LVDS CABLE-15.6
NIWE1 CAMERA 0.3M
NIWE2 WLAN ANTENNA-15.6
NIWE2 WWAN ANTENNA-15.6
NIWE2 LCD COVER NISSHA 15.6 W/ANT*2-IMR
NIWE2 LCD COVER REIKO 15.6 W/ANT*2-IMR
NIWE2 LCD COVER 15.6 W/ANT*2-TEXTURE
31042411
31042412
31042413
31042434
18003797
18003819
18003911
18003719
TBD
31042430
31042432
31042438
31042425
31042428
31042419
31042421
31042423
85
Lenovo G560 Hardware Maintenance Manual
Keyboard
Table 7. Parts list—Keyboard
Language
JME
86
P/N
German
Arabic
Brazilian
English
U.K. English
Italian
Spanish
Turkish
Thai
Portuguese
Latin
Korean
Traditional Chinese
Russian
French
Japanese
Czech
Dutch
Greek
Hebrew
Hungarian
Belgian
Icelandic
Slovak
Slovenian
Swiss
International English
Canadian English&French
Four Nordic countries
Bulgarian
25009958
25009959
25009960
25009754
25009929
25009961
25009962
25009963
25009964
25009965
25009966
25009967
25010117
25009969
25009970
25009922
25009971
25010118
25010119
25010120
25009863
25009864
25009865
25009866
25009867
25009868
25009869
25009870
25009871
25009872
Lenovo G560
Table 7. Parts list—Keyboard (continued)
Language
Chicony
P/N
English
U.K. English
Italian
Spanish
Turkish
Thai
Portuguese
Latin
Korean
Traditional Chinese
Russian
French
German
Arabic
Brazilian
Japanese
Hungarian
Czech
Greek
Dutch
Hebrew
Belgian
Icelandic
Slovak
Slovenian
Swiss
International English
Canadian English&French
Four Nordic countries
Bulgarian
25009755
25009873
25009874
25009875
25009876
25009877
25009878
25009879
25009880
25009881
25009809
25009810
25009811
25009812
25009813
25009814
25009815
25009816
25009817
25009818
25009819
25009820
25009821
25009822
25009823
25009824
25009825
25009826
25009827
25009588
87
Lenovo G560 Hardware Maintenance Manual
Miscellaneous parts
Table 8. Parts list—Miscellaneous parts
FRU
System miscellaneous parts:
• (a) NIWE1 TP BRACKET
• (b) NIWE1 HDD BRACKET
• (c) NIWE1 ODD BRACKET
Cable miscellaneous parts:
• (d) NIWE2 DC-IN CABLE-15.6
• (e) NIWE2 USB CABLE-15.6
• (f) NIWE1 BT CABLE
• (g) NIWE2 TP FFC-15.6
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 80.
88
P/N
31042384
31042377
31042381
31042402
31042399
31042403
31042386
Lenovo G560
AC adapters
Table 9. Parts list—3-pin AC adapters
FRU
P/N
65W3PIN, Delta ADP-65KH B adapter
65W3PIN, Liteon PA-1650-56LC adapter
65W3PIN, Chicony CPA-A065 20V3.25A adapter
65W3PIN, Brazil PA-1650-52LB adapter
36001646
36001651
36001792
36001714
89
Lenovo G560 Hardware Maintenance Manual
Power cords
A Lenovo power cord for a specific country or region is usually available only in
that country or region:
Table 10. Parts list—3-pin power cords
90
Region
P/N
CCC
• SSD YD-118-1+IEC53RVV+SSD-3-2B-1 1m
CCC
• LINETEK PC323+RVV300/300+LS15 1m
Argentina
• LINETEK LS15+H03VV-F+LP39 1m
Danmark
• LINETEK LS15+H03VV-F+LP-38 1m
Switzerland
• LINETEK LS15+H03VV-F+LP-37 1m
Brazil
• LINETEK LS15 H03VV-F LP26A 1m
Israel
• LINETEK LS15+H03VV-F+LP-41 1m
UL
• LINETEK LP-30B + SPT-2 + LS15 1m
UL
• LINETEK LP-30B + SPT-2 + LS15 1.5m
UK
• LINETEK LP-61L+ H03VV-F+ LS15 1m
Indian
• LINETEK PE-361+ H05VV-F+ LS15 1m
Italy
• LINETEK LS15+H03VV-F+PE-336 1m
Korea
• LINETEK LS15+H05VV-F+LP-E04A 1m
Australia
• LINETEK LS15+H03VV-F+LP-23A 1m
Taiwan
• LINETEK LS15+VCTF+LP-53 1m
Japan
• LINETEK LS15+VCTF+LP-54 1m
Africa
• LINETEK LS15+H03VV-F+PE-364 1m
CE
• LINETEK LP-34+H03VV-F + LS15 1m
CCC
• Longwell LSG-31+RVV300/300+LS-18 1m
Argentina
• Longwell LP-24+H03VV-F+LS-18 1m
Danmark
• Longwell LP-40+H03VV-F+LS-18 1m
145000602
145000600
145000599
145000598
145000597
145000596
145000595
145000594
145000635
145000593
145000592
145000591
145000590
145000589
145000588
145000587
145000586
145000585
145000568
145000567
145000566
Lenovo G560
Table 10. Parts list—3-pin power cords(continued)
Region
P/N
Switzerland
• Longwell LP-37+H03VV-F+LS-18 1m
Brazil
• Longwell LP-46+H03VV-F+LS-18 1m
Israel
• Longwell LP-41+H03VV-F+LS-18 1m
UL
• Longwell LP-30B+SPT-2 18AWG+LS-18 1m
UL
• Longwell LP-30B+SPT-2+LS-18 1.5m
UK
• Longwell LP-61L+H03VV-F+LS-18 1m
Indian
• Longwell LP-67+BIS+LS-18 1m
India
Italy
• Longwell LP-22+H03VV-F+LS-18 1m
Korea
• Longwell LP-486+KTLH03VV-F+LS-5 1m
Australia
• Longwell LP-23A+LFC-3R+LS-18 1m
Taiwan
• Longwell LP-71+VCTF+LS-33 1m
Japan
• Longwell LP-54+VCTF+LS-18 1m
Africa
• Longwell LP-39+H03VV-F+LS-18 1m
CE
• Longwell LP-34A+H03VV-F+LS-18 1m
145000565
145000564
145000563
145000562
145000633
145000561
145000560
42T5083
145000559
145000558
145000557
145000556
145000555
145000554
145000553
91
Lenovo G560 Hardware Maintenance Manual
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
L E N O V O G R O U P LT D . P R O V I D E S T H I S P U B L I C AT I O N “ A S I S ”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
will be incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this Lenovo product, and use of those Web sites is at your own risk.
92
Notices
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.
Trademarks
The following terms are either registered trademarks or trademarks of Lenovo
in the United States and/or other countries:
Lenovo®
Lenovo logo®
IdeaPad®
VeriFace®
OneKey Rescue®(OneKey Recovery, OneKey Antivirus)
APS®
Power Express®
Energy Management and ReadyComm®
The following terms are trademarks of Microsoft Corporation in the United
States, other countries, or both:
Windows®
Windows Vista®
The following are trademarks of Intel Corporation or its subsidiaries in the
United States, other countries, or both:
Intel®
Intel® Core™ 2 Duo
Other company, product, or service names may be the trademarks or service
marks of others.
93
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement