360 Imaging™ 360 Imaging™

360 Imaging™ 360 Imaging™
360 Imaging™
Installation Guide
532050-1_B
Thank You!
Thank you for choosing Humminbird®, the #1 name in Fishfinders. Humminbird® has
built its reputation by designing and manufacturing top-quality, thoroughly reliable
marine equipment. Your Humminbird® accessory is designed for trouble-free use in
even the harshest marine environment. In the unlikely event that your Humminbird®
accessory does require repairs, we offer an exclusive Service Policy - free of charge
during the first year after purchase, and available at a reasonable rate after the
one-year period. For complete details, see the separate warranty card included with
your accessory. We encourage you to read this manual carefully in order to get full
benefit from all the features and applications of your Humminbird® product.
Contact our Customer Resource Center at 1-800-633-1468 or visit our Web site at
humminbird.com.
WARNING! This device should not be used as a navigational aid to prevent collision,
grounding, boat damage, or personal injury. When the boat is moving, water depth may
change too quickly to allow time for you to react. Always operate the boat at very slow speeds
if you suspect shallow water or submerged objects.
WARNING! The electronic chart in your Humminbird® unit is an aid to navigation designed
to facilitate the use of authorized government charts, not to replace them. Only official
government charts and notices to mariners contain all of the current information needed for
the safety of navigation, and the captain is responsible for their prudent use.
WARNING! Humminbird® is not responsible for the loss of data files (waypoints, routes,
tracks, groups, recordings, etc.) that may occur due to direct or indirect damage to the unit’s
hardware or software. It is important to back up your control head’s data files periodically. Data
files should also be saved to your PC before restoring the unit’s defaults or updating the
software. See your Humminbird® online account at humminbird.com and the Waypoint
Management Guide on your Humminbird® Manual CD for details.
WARNING! Disassembly and repair of this electronic unit should only be performed by
authorized service personnel. Any modification of the serial number or attempt to repair
the original equipment or accessories by unauthorized individuals will void the warranty.
WARNING! This product contains chemicals known to the State of California to cause
cancer and/or reproductive harm.
ATTENTION INTERNATIONAL CUSTOMERS: Products sold in the U.S. are not intended for
use in the international market. Humminbird® international units provide international
features and are designed to meet country and regional regulations. Languages, maps, time
zones, units of measurement, and warranty are examples of features that are customized
for Humminbird® international units purchased through our authorized international
distributors.
To obtain a list of authorized international distributors, please visit our Web site at
humminbird.com or contact our Customer Resource Center at (334) 687-6613.
ROHS STATEMENT: Product designed and intended as a fixed installation or part of a system
in a vessel may be considered beyond the scope of Directive 2002/95/EC of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
NOTE: Some features discussed in this manual require a separate purchase, and some features
are only available on international models. Every effort has been made to clearly identify those
features. Please read the manual carefully in order to understand the full capabilities of your
model.
NOTE: The illustrations in this manual may not look the same as your control head, but your
product will function in the same way.
NOTE: To purchase accessories for your control head, visit our Web site at humminbird.com
or contact our Customer Resource Center at 1-800-633-1468.
NOTE: The procedures and features described in this manual are subject to change without
notice. This manual was written in English and may have been translated to another language.
Humminbird® is not responsible for incorrect translations or discrepancies between documents.
NOTE: The installation of this advanced accessory should be performed by a qualified marine
technician.
360 Imaging™, 700 Series™, 800 Series™, 900 Series™, 1100 Series™, Humminbird®, WeatherSense®, and
X-Press™ Menu are trademarked by or registered trademarks of Johnson Outdoors Marine Electronics, Inc.
© 2013 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
Table of Contents
Introduction
1
Installation Overview
2
Install the GPS Receiver/Heading Sensor
6
1. Choose the Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Install the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A. Stem Mount with 1” - 14 Thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
B. Access Under the Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C. No Access Under the Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. Connect to the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Install the Transducer Deployment System
16
1. Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Choose the Mounting Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Install the Transom Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4. Install the Transducer Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5. Install the Transducer Deployment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6. Route the Cables and Connect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7. Test the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Set up the Control Head
32
1. Power on and Confirm Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2. Set up 360 Imaging™ on the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3. Test 360 Imaging™ on the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4. Confirm the Heading Sensor Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5. Confirm the Baud Rate (for devices connected to the Sensor pigtail only) . . . . . . . . . . 40
6. Set up the Network and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Power Off
41
i
Table of Contents
Maintenance
42
Control Head Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Transducer Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Transducer Deployment System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Troubleshooting
44
Fishing System Doesn’t Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Fishing System Defaults to Simulator with a Transducer Attached . . . . . . . . . . . . . 45
The Pod Doesn’t Deploy or Retract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Finding the Cause of Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Removing the Pod (for authorized repair only)
48
Reconnecting the Pod (for authorized repair only)
51
Specifications
54
Contact Humminbird®
56
ii
Introduction
This manual will guide you through the following installation requirements for the
360 Imaging™ Transducer Deployment System:
Installing the GPS Receiver/Heading Sensor
Installing the Transducer Deployment System
Connecting to the Control Head and Power
Testing the Installation
Powering Off
Before proceeding with this installation, the Humminbird® control head
should be installed. See your Humminbird® control head installation guide
for instructions. The 360 Imaging™ Transducer Deployment System can
be connected directly to the control head or to a Humminbird® Ethernet
Switch (optional) for networking. See the Ethernet Switch accessory guide
to install the Ethernet Switch.
NOTE: The installation of this advanced accessory should be performed by a qualified marine
technician.
1
Introduction
1 | Installation Overview
Before you start the installation, please take a moment to familiarize yourself with the
parts list and supplies list. We also encourage you to read the instructions beforehand
so that you may understand the installation requirements.
A
B
N
G
C
O
D
E
F
P
H
L
Q
I
J
M
K
Installation
2
Parts
The 360 Imaging™ Transducer Deployment System includes the following items:
A
Transducer Deployment System
B
Transom Bracket
H
C
(4) 5/16" - 18 Hex Lock Nuts
D
(4) 5/16" Split Ring Lock Washers
E
(4) 5/16" Flat Washers
F
(4) 5/16" Fender Washers
G
(4) 5/16" - 18, 3 1/2" Bolts
Transducer Bracket
I
(8) 1/4" - 20 Flat Washers
J
(4) 1/4" Split Ring Lock Washers
K
(4) 1/4" - 20 Hex Lock Nuts
L
(2) 1/4" - 20, 3 3/4" Bolts
M
(2) 1/4" - 20, 3 1/4" Bolts
N
Anti-Seize Tube
O
GPS Receiver/Heading Sensor and screws for mounting
P
Power Cable (6', 2 m)
Q
Ethernet Cable (20', 6 m)
Pod Cover (not shown)
NOTE: Product supplies and features are subject to change without notice.
3
Installation
Supplies
In addition to the hardware included with your Transducer Deployment System, you
will need the following supplies:
Drill with various drill bits
Electrical tape
Awl or pencil
1/2" & 7/16" sizes in wrenches, ratchets, and sockets
Torque wrench with 5 - 7 FT/LB capacity
3M Marine Adhesive Sealant 5200 (recommended)
or Marine Grade Adhesive Sealant
Marine-grade silicone caulk or sealant
Cable ties for cable routing
4' straight edge or level
Tape measure
8 A fuse
Safety goggles
Dust mask
Cables: Depending on your Humminbird® model and system configuration, you
may need to purchase additional cables, as shown below. Visit our Web site at
humminbird.com or call our Customer Resource Center at 1-800-633-1468.
• 700 Series™ with Ethernet: To connect the Ethernet to the control head,
you will need to purchase the Ethernet Adapter Cable (AS EC QDE).
• Extention Cables are available for Ethernet and the GPS Receiver/Heading
Sensor.
• Y-Cable: If the COM port on the control head is already used by another
installed accessory, you will need to purchase a Humminbird® Y-Cable to
add the GPS Receiver/Heading Sensor to the installation.
Installation
4
Switch (optional): If you do not have a main switch or fuse panel available on
your boat to connect power, you will need to purchase a battery switch. See
Install the Transducer Deployment System, Section 6. Route the Cables and
Connect Power for more information.
Lag Bolts (optional): If you are unable or choose not to drill completely through
the transom as recommended, you will need to purchase (4) 5/16" lag bolts of
the appropriate length.
5
Installation
Install the GPS Receiver/Heading Sensor
Use the following instructions to install the GPS Receiver/Heading Sensor (“Sensor”)
on your boat.
1. Choose the Mounting Location
It is important to consider the following information when you choose a mounting
location for the Sensor:
• Interference: Do NOT mount the Sensor close to a VHF antenna or within the
active area of a radar. Do NOT install the Sensor near ferrous metals or near
anything that can create a magnetic field. Hardware and cables that handle
large currents, such as batteries and power cables, are also examples of
equipment that may cause interference.
• Reception: Mount the Sensor in an area that has full exposure to the sky. The
effective area of reception is 5˚ above the horizon.
• Surface: Whether the Sensor Cable will be routed down through the
mounting surface or to the side, or if your’re using a stem mount, the
mounting surface will influence how you install the Sensor. For details, see
Section 2: Install the Sensor.
• Extension Cables: Test run the Sensor Cable from the chosen mounting
location to the control head. 10 ft (3m) extension cables may be purchased from
Humminbird® if your planned cable route exceeds 20 ft (6 m). Maximum cable
length, including extension cables, should not exceed 50 ft (16 m).
• Y-Cable: If the COM port on the control head is already used by another
installed accessory, you will need to purchase a Humminbird® Y-Cable to add
the Sensor to the installation.
Installation - GPS/Heading Sensor
6
2. Install the Sensor
There are three different options to mount the sensor. Proceed to the section that
matches the type of mounting location you will be using, as follows:
Stem Mount with 1” - 14 Thread
The Sensor will be mounted on a stem or
antenna pole. Proceed to Section A.
Stem
Access Under the Mounting Deck
The Sensor will be deck mounted and the
cable can be routed down through the
mounting surface. Proceed to Section B.
Cable routed through the hole
NO Access Under the Mounting Deck
The Sensor will be deck mounted and the
cable must routed to the side because there is
not space for a cable through or underneath
the mounting location. Proceed to Section C.
Cable routed to the side
7
Installation - GPS/Heading Sensor
A. Stem Mount with 1”-14 Thread
Use the following instructions to stem mount the Sensor:
WARNING! Do NOT mount the Sensor to a stem
mount or antenna pole that contains ferrous metals.
NOTE: It is important to review the mounting
considerations and test run the cable route as
indicated in Section 1 before proceeding with the
installation.
1. If you have a pre-existing stem mount, skip to
step 2.
If you need to mount the antenna pole (stem),
mark the chosen mounting location and drill a
3/4” (19 mm) hole for the cable and cable
connector.
Stem Mount, Attaching the
Sensor Base to the Stem
Cover
Base
Stem
Taping the NMEA Pigtail
to the Cable
If you have purchased hardware to stem
mount your Sensor, follow the instructions
included with that hardware to attach the stem
to the boat.
NMEA
Pigtail
Cable
Taped
2. Screw the Sensor base onto the stem first,
making sure that the stem pipe does not
protrude from the Sensor base. (This adds
protection to the cable when it is pulled through
the pipe stem.) Deburr the pipe edges to reduce
cable abrasion.
3. Use electrical tape to secure the NMEA pigtail
to the cable.
NOTE: Unless it is needed, leave the NMEA pigtail
secured to the cable. If you are connecting the pigtail to
a NMEA 0183 device, see Section 3: Connect to the
Control Head for connection information.
Installation - GPS/Heading Sensor
8
NMEA Pigtail Cable Out
4. Route the Sensor cable through the stem and
through the planned cable route. To use
extension cables, see the details in Section 1:
Choose the Mounting Location.
Positioning the Arrow
on the Sensor
5. Position the Sensor so the arrow on the cover
is pointed straight toward the front of the boat
in the direction of travel. The arrow should be
parallel with the keel.
NOTE: Failure to align the Sensor correctly will result in
incorrect compass readings.
6. Attach the Sensor to its base using the
included #6 -1/4” screws. Hand tighten only.
Attaching the Sensor
to the Base
#6 -1/4
Mounting Screws
9
Installation - GPS/Heading Sensor
B. Access Under the Mounting Location
Use the following instructions to deck mount the Sensor and route the cable down
through the mounting surface:
NOTE: It is important to review the mounting considerations and test run the cable
route as indicated in Section 1 before proceeding with the installation.
1. Mark the mounting location and drill a 3/4”
(19 mm) hole for the cable and cable connector.
Taping the NMEA Pigtail
to the Cable
2. Secure the NMEA pigtail to the cable with
electrical tape.
NOTE: Unless it is needed, leave the NMEA pigtail
secured to the cable. If you are connecting the pigtail
to a NMEA 0183 device, see Section 3: Connect to
the Control Head for connection information.
NMEA
Pigtail
Cable
Taped
3. Route the Sensor cable through the planned
cable route. To use extension cables, see the
details in Section 1: Choose the Mounting
Location.
4. Cover the cable hole with the Sensor.
Position the Sensor so the arrow on the cover
is pointed straight toward the front of the boat
in the direction of travel. The arrow should be
parallel with the keel.
NOTE: Failure to align the Sensor correctly will result
in incorrect compass readings.
Installation - GPS/Heading Sensor
10
NMEA Pigtail Cable Out
5. Make sure the Sensor is flush against the surface, and mark the two
mounting holes with a pencil or awl.
6. Move the Sensor to the side and drill two pilot holes, using a 5/32”
(4 mm) bit.
NOTE: Apply marine-grade silicone caulk or sealant to both screw and drilled holes as
needed to protect your boat from water damage.
7. Align the Sensor’s screw holes over the pilot screw holes and attach with the
#6 - 3/4” Phillips head screws. Hand tighten only.
NOTE: If the mounting surface is thin or made of a light-weight material, you may
need to add reinforcing material below the mounting surface in order to support the
Sensor.
Positioning the Arrow
on the Sensor
Attaching the Sensor to the
Mounting Surface
#6 - 3/4
Mounting Screws
Cable routed through the hole
11
Installation - GPS/Heading Sensor
C. No Access Under the Mounting Location
Use the following instructions to deck mount the Sensor and route the cable to the
side if there is not space for a cable underneath the mounting location:
NOTE: It is important to review the mounting considerations and test run the cable
route as indicated in Section 1 before proceeding with the installation.
1. Secure the NMEA pigtail with electrical tape.
NOTE: Unless it is needed, leave the NMEA pigtail
secured to the cable. If you are connecting the pigtail
to a NMEA 0183 device, see Section 3: Connect to
the Control Head for connection information.
Taping the NMEA Pigtail
to the Cable
2. Route the cable from the Sensor to the Control
head.
• The Sensor has two wire routing notches.
Use the cable notch closest to the
intended cable route.
NMEA
Pigtail
Cable
Taped
• If holes are required to route the cable,
they must be 3/4” (19 mm) to allow for the
cable connector.
• To use extension cables, see the details in
Section 1: Choose the Mounting Location.
NMEA Pigtail Cable Out
Installation - GPS/Heading Sensor
12
3. With the cable routed, position the Sensor so
the arrow on the cover is pointed straight
toward the front of the boat in the direction of
travel. The arrow should be parallel with the
keel.
Positioning the Arrow
on the Sensor
NOTE: Failure to align the Sensor correctly will result in
incorrect compass readings.
4. Make sure the Sensor is flush against the
surface, and mark the two mounting holes
with a pencil or awl.
5. Move the Sensor to the side and drill the two
5/32” (4 mm) pilot holes.
NOTE: Apply marine-grade silicone caulk or sealant to
both screw and drilled holes as needed to protect your
boat from water damage.
6. Align the Sensor’s screw holes over the pilot
screw holes and attach with the #6 - 3/4”
Phillips head screws. Hand tighten only.
Attaching the Sensor to the
Mounting Surface
#6 - 3/4
Mounting Screws
Cable routed to the side
13
Installation - GPS/Heading Sensor
3. Connect to the Control Head
Use the following instructions to connect the Sensor cable to the control head.
1. Insert the Sensor’s NMEA-COM connector into the control head’s COM port.
The connectors are keyed to prevent reversed installation, so be careful not
to force the connector into the port.
• If there is another accessory plugged into the COM port, install the
AS YC ("Y") cable (optional-purchase required).
• Attach the COM connector of the Y-cable directly to the control head
COM port. Connect the Sensor to the NMEA-COM connector of the
Y-cable. Reconnect your other Fishfinder accessories to the ACCY-COM
connector of the Y-cable. See the illustration Optional Configuration(s)
for the Sensor Installation.
2. Optional: The control head outputs NMEA signals through the Sensor’s
pigtail cable for connection to a device such as an autopilot. Connect the
NMEA Out (White Wire) of the cable to the NMEA In of the device you are
connecting to your Fishfinder. The pinouts of this cable are as follows:
• Green Wire, GPS NMEA Out
• Black Wire, Ground
• White Wire, Control Head NMEA Out
NOTE: See the illustration Optional Configuration(s) for the Sensor Installation.
WARNING! It is important to finish all installation connections before powering
on the control head.
Installation - GPS/Heading Sensor
14
Optional Configuration(s) for the Sensor Installation
Optional: Using a Y-Cable to
connect multiple accessories
to the COM Port.
Optional: Using the Sensor wires to
connect to a separately-purchased
device. Also, see Confirm the Baud
Rate for more information.
15
Installation - GPS/Heading Sensor
Install the Transducer Deployment System
Use the following instructions to install the Transducer Deployment System.
NOTE: Due to the wide variety of hulls, only general instructions are presented
in this installation guide. Each boat hull represents a unique set of requirements
that should be evaluated prior to installation. It is important to read the
instructions completely and understand the mounting guidelines before you
start the installation.
1 | Installation Overview
There are two mounting options available for installing the Transducer Deployment
System.
• Direct Transom Mount: Included
• Optional Mounting Brackets: If you do not want to mount the Transducer
Deployment System directly to the transom, you'll need a mounting bracket
to offset the unit from the back of the boat. For more information, visit
humminbird.com.
Installation - Transducer
16
2 | Choose the Mounting Location
It is important to review the following mounting location requirements, as follows:
• Port (left) or Starboard (right): The Transducer Deployment System can be
mounted on either side of the transom. If there is heavy equipment on one
side, install the Transducer Deployment System on the opposite side. Do not
install it behind the propeller.
• Height: Install the mounting bracket in the highest possible location. This will
provide the most stable support and the greatest amount of vertical and angular
adjustability. The bottom edge of the pod should be no less than 8 inches
(20.3 cm) above the bottom line of the hull to prevent spray and drag conditions.
The pod should sit at or above the waterline when the boat is at rest.
Installation Height, at least 8” (20.3 cm) above the bottom line of the hull
8”
Continued...
17
Installation - Transducer
• Engine Obstruction: Trim the engine to its lowest position and steer the
engine fully to the selected mounting side. Confirm that there is at least
6 inches (15.3 cm) of clearance from any point on the Transducer Deployment
System, especially from the deployed pod to the propeller.
• Clear Path Below: The transducer pod must have a clear, unobstructed path
to deploy without hitting trim tabs, poling platforms, ladders, engine, or other
obstructions.
• Unobstructed View: Once deployed, the transducer pod must NOT have
anything obstructing the ‘view’ of the rotating beams. Nothing should be in
the line of sight of these beams (not a hull, motor, trolling motor, etc). The
transducer pod descends 29 inches (73.7 cm) when it is deployed.
Distance from Engine and Open Path for Deployment
6”
Trim the engine to
the lowest point and
steer it to the selected
mounting side.
Installation - Transducer
18
• Transom Obstructions: Review the transom to confirm that you will not drill
into any obstructions (lines, hoses, gas tank, etc.) and that there is enough
space for the hardware to be installed.
• Space Above: Confirm that the boat’s platform will not interfere with the
operation of the Transducer Deployment System.
• Power: The Transducer Deployment System is powered separately from the
control head. It must be connected to a switch where it can be powered on
when the boat is underway and powered off when it is docked. See Section
6. Route the Cables and Connect Power for more information.
• Cables: Test run the Ethernet cable from the chosen mounting location to the
control head (or optional Ethernet Switch). Test run the power cable from the
chosen mounting position to the main switch or fuse panel. The cable ports
are located at the top of the Transducer Deployment System, so it is important
to consider the distance and height required to route from the ports.
The cables should be routed through an established routing system on the
boat, in an area with minimal interference, without sharp edges, obstacles,
or obstructions that may damage the cables.
NOTE: To purchase Ethernet extension cables or an adapter cable, visit our Web
site at humminbird.com or call our Customer Resource Center for details at
1-800-633-1468.
19
Installation - Transducer
3 | Install the Transom Bracket
1. Confirm that the boat is level on the trailer, both from port to starboard and
from bow to stern, by placing your level on the deck of the boat, first in one
direction, then in the other.
2. Position the transom bracket in your selected location. Use a level to confirm
the bracket is level horizontally.
Leveling the Transom Bracket in the Selected Mounting Location
3. Mark the bracket mounting holes.
4. Make sure the drill bit is perpendicular to the transom, NOT parallel to the
ground, before you drill. Use a 5/16” (8 mm) drill bit to drill the four marked
holes.
5. Apply a 1/8" (3 mm) bead of 3M 5200 Marine Adhesive Sealant around each
of the four drilled holes and to the the perimeter of the transom bracket,
staying approximately ½" (1.3 cm) from the outside edge.
Installation - Transducer
20
6. Use the illustration Attaching the Bracket to the Transom to install the
3 1/2” (8.9 cm) bolts and hardware in each of the four bracket holes. Apply
Anti-Seize to the end of each bolt as you are installing the hardware. Hand
tighten the nuts with a socket wrench. DO NOT OVERTIGHTEN.
Attaching the Bracket to the Transom
5/16”
Hex Lock Nut
5/16” Fender
Washer
5/16” Flat
Washer
5/16” Split
Ring Lock
Washer
5/16” x 3 1/2“
Bolt
Transom
(partial view)
21
Installation - Transducer
4 | Install the Transducer Bracket
Use the following instructions to install the transducer bracket onto the transom
bracket.
1. Insert the transducer bracket into the arms of the transom bracket so that the
holes are aligned and the transducer bracket is level vertically. You will
finalize the angle and installation in the following steps.
NOTE: To lower the pod height by 3” (7.6 cm), the transducer bracket can be mounted
upside down. This type of installation can be used if the boat’s transom is very tall or
if the boat has a reversed transom.
Adjusting the Angle of the
Transducer Bracket
Alternative Installation
(may be needed for reversed transoms
or to lower the height of the pod)
Transducer
Bracket
Level
Transducer
Bracket
installed
upside
down
The bracket holes
allow you to set
the angle of the
transducer bracket.
Installation - Transducer
Level
22
2. Install the first 3 3/4“ (9.5 cm) bolt and hardware as shown in the illustration
Installing the Transducer Bracket Hardware. Apply Anti-Seize to the end of
each bolt as you are installing the hardware.
3. Adjust the bracket so that the bracket holes are aligned and the transducer
bracket is level vertically. See the illustration Installing the Transducer
Bracket Hardware to install the second set of hardware, using the same
installation order as the first set of hardware.
4. Hand-tighten both bolts on the transducer bracket so it is secured.
5. Place a level on the transducer bracket. Confirm it is level vertically (see the
illustration Adjusting the Angle of the Transducer Bracket).
Installing the Transducer Bracket Hardware
Transducer
Bracket
Install 2nd
1/4” x 3 3/4”
Bolt to
set the angle
1/4”
Hex Lock
Nut
Install 1st
1/4” x 3 3/4”
Bolt
1/4” Split Ring
Lock Washer
1/4” Flat
Washer
1/4” Flat
Washer
23
Installation - Transducer
5 | Install the Transducer Deployment System
Use the instructions in this section to secure the Transducer Deployment System to
the transducer bracket.
1. Carefully lift the Transducer Deployment System and align its track with the
track on the transducer bracket.
2. Slide the Transducer Deployment System down the track until the pod is
approximately 8" (20 cm) above the bottom line of the hull.
3. Align the bracket holes and install the two 3 1/4” (8.3 cm) bolts and hardware
as shown in the illustration Installing the Transducer Deployment System.
NOTE: Apply Anti-Seize to the end of each bolt as you are installing the hardware.
Installing the Transducer Deployment System
1/4” Split Ring
Lock Washer
1/4” Flat
Washer
1/4” Hex
Lock Nut
1/4” x 3 1/4”
Bolt
1/4” Flat
Washer
Installation - Transducer
24
4. Place a straight edge along the bottom of the hull and measure the distance
to the bottom of the transducer pod. Confirm that the the pod is 8” (20.3 cm)
above the bottom line of the hull. If you need to make adjustments to the pod
height, consider the following:
• To adjust the height of the Transducer Deployment System, re-install the
hardware in step three on a higher or lower set of holes.
• If you cannot lower the Transducer Deployment System any further
based on the installation location of the transom bracket, you can lower
the height by 3” (7.6 cm) by mounting the transducer bracket upside
down. Uninstall the Transducer Deployment System, and return to the
Install the Transducer Bracket section.
NOTE: Additional adjustments may need to be made after a trial run on the water.
Installation Height, at least 8” (20.3 cm) above the bottom line of the hull
8”
25
Installation - Transducer
5. Place a level on the Transducer Deployment System. Confirm it is level
horizontally and vertically. The pod should be parallel with the water. If the
angle needs to be adjusted, return to the section Install the Transducer
Bracket.
6. Fully hand-tighten the nuts and then turn them 1/4 more. Tighten the
transducer bracket hardware securely so that the assembly is stable and
secure. Hand tighten only.
NOTE: It is important to check the tension of the four vertical nuts on the transducer
bracket hardware after initial use and periodically thereafter to ensure that the
Transducer Deployment System remains stable. It is also important to confirm that
the Transducer Deployment System stays level when the boat is on the water.
Confirming that the Transducer Deployment System is Level
Installation - Transducer
26
6 | Route the Cables and Connect Power
The cables should be routed through an established routing system on the boat, in
an area with minimal interference. Inspect the selected route carefully to ensure that
there are no sharp edges, obstacles, or obstructions that may damage the cables.
See Section 2. Choose the Mounting Location for details.
WARNING! The power source must be turned off before you proceed with this installation.
1. Remove the Port Cover.
Removing the Port Cover
2. Ethernet: Insert the Ethernet Cable Connector
into the Ethernet port on the Transducer
Deployment System. The connectors are keyed
to prevent reversed installation, so be careful
not to force the connector into the port.
3. Hand-tighten the screw nut.
4. Route the Ethernet Cable down through the
cable channel on the Transducer Deployment
System, tucking the cable into the channel as
Hand-tightening the Screw Nut
you go. Route the cable to the control head (or
the optional Ethernet Switch).
5. Insert the other end of the Ethernet Cable into
the Ethernet port on the control head. Handtighten the screw nut.
NOTE: If you have a 700 Series™ unit with Ethernet,
connect the Ethernet Cable to the Ethernet Adapter
Cable (AS EC QDE). Insert the connector into the
Ethernet port on the cable collector. See your control
head installation guide for details about installing the
quick disconnect mount.
27
Screw
Nut
The connectors are keyed to
prevent reversed installation.
Installation - Cables
700 Series™ Cable Collector with Ethernet
Ethernet
800/900 Series™ (rear view)
Ethernet Port
1100 Series™ (rear view)
Installation - Cables
28
WARNING! The Transducer Deployment System should be connected to a
main switch, fuse panel, or battery switch. Humminbird® does not recommend
connecting to a battery without a fuse and a switch.
NOTE: Humminbird® is not responsible for over-voltage or over-current failures. The
Transducer Deployment System must have adequate protection through the proper
selection and installation of an 8 Amp fuse.
NOTE: A 6' (2 m) long power cable is included to supply power to the Transducer
Deployment System. You may shorten or lengthen the cable using 18 gauge multi-stranded
copper wire.
CAUTION! Some boats have 24 or 36 Volt electric systems, but the Transducer Deployment
System MUST be connected to a 12 VDC power supply.
6. Power: Insert the Power Cable Connector into
the Power port on the Transducer Deployment
System. The connectors are keyed to prevent
reversed installation, so be careful not to force
the connector into the port. Hand-tighten the
screw nut.
7. Route the Power Cable down through the cable
channel on the Transducer Deployment
System, tucking the cable into the channel as
you go.
Routing the Cables
through the Cable Channel
Cable
Ports
Cable
Channel
8. Route the power cable to the main switch or
fuse panel (usually located near the console). If
you must connect to a battery, connect to a
battery switch (not included).
29
Installation - Cables
9a. Main Switch/Fuse Panel: If a fuse terminal is Connecting to the Fuse Panel
available, use crimp-on type electrical
connectors (not included) that match the
terminal on the fuse panel. Attach the black
wire to ground (—), and the red wire to
positive (+) 12 VDC power. Install an 8 Amp
fuse (not included) for protection of the unit.
OR
9b. Battery Switch: Install the battery switch (not
included) using the instructions provided with
it. You will also need to obtain and install an
inline fuse holder and an 8 Amp fuse (not
included) for the protection of the unit. Attach
the black wire to ground (—), and the red wire
to positive (+) 12 VDC power.
WARNING! If you are unable to obtain a battery switch and are forced to connect the
power cable directly to the battery, be aware that this will drain the battery. Humminbird®
does not recommend connecting to a battery without the appropriate fuse and a switch.
10. Secure the cables with cable ties along the route as needed for a clean
assembly.
11. Re-install the Port Cover.
Installation - Cables
30
7 | Test the Installation
1. Carefully inspect the area around the Transducer Deployment System for any
obstructions that may interfere with deployment.
2. Turn on the power source from the switch.
3. Standing clear of the Transducer Deployment System, press and hold the
– key to deploy the transducer pod.
4. The transducer pod will begin to deploy. Release the – key when the
transducer pod has been deployed sufficiently to determine it is working.
5. Press and hold the
stowed.
• key. Release the key when the transducer pod is fully
NOTE: If the transducer did not deploy successfully, check the power connections at the
switch and on the Transducer Deployment System. See Section 6. Route the Cables and
Connect Power and Troubleshooting for more information.
— Key
Deploy
• Key
Retract
31
Installation - Test
Set up the Control Head
Use the following instructions to power on the control head and confirm the
360 Imaging™ transducer and the GPS Receiver/Heading Sensor are detected by the
unit.
CAUTION! It is important to finish all installation connections before powering
on the control head. It may take up to a minute for the 360 Imaging™
transducer and other attached equipment to be detected by the control head.
1. Power on and Confirm Connections
1. Turn on the power source from the main switch.
2. On the control head, press the
POWER/LIGHT key. If you are powering
on a control head in a multiple-control head Ethernet network, power on
the control head that is connected to the 360 Imaging™ Transducer
Deployment System first.
3. When the Title screen is displayed, press the MENU key to access the StartUp Options Menu.
4. Use the 4-WAY Cursor Control key to choose Normal, and press the RIGHT
Cursor key to select it.
5. Press and hold the VIEW key. Select System > Accessory Test. Confirm that
AS 360 and GPS + Heading Sensor are listed as Connected. It will take a
minute for the equipment to be detected.
6. Press and hold the VIEW key. Select System > GPS Diagnostic View. Confirm
that External GPS is displayed and the Fix Type indicates Enhanced or 3D.
NOTE: If the GPS Diagnostic View or Accessory Test is not displayed in the View Rotation,
press the MENU key twice to open the Main Menu. Select the Views tab > GPS Diagnostic
View or Accessory Test. Change the setting for each view to Visible.
Installation - Set up the Control Head
32
Title Screen
Accessory Test
AS 360 listed
as Connected
GPS &
Heading
Sensor listed
as Connected
GPS Diagnostic View
Fix Type
should be 3D
or Enhanced
External GPS
Detected
33
Installation - Set up the Control Head
2. Set up 360 Imaging™ on the Control Head
To deploy the transducer from the control head, the transducer must be selected from
the network, and the deployment depth should be set in advance. When you select
the 360 Imaging™ transducer from the network, the related views and menus will be
added to the system.
Selecting the 360 Imaging™ Transducer
Press the
RIGHT or
LEFT Cursor
keys to
select a tab.
Use the 4-WAY
Cursor Control
key to choose the
transducer, and
press the RIGHT
Cursor key or the
CHECK/INFO key
to select it.
1. Select 360 Imaging™ on the Network
Confirm that AS 360 is selected in the Network Source Setup dialog box. It might
take up to a minute for the equipment to be detected.
NOTE: If AS 360 is already selected (indicated by a check mark), you can skip this step.
Proceed to Set the Deployment Depth.
1. Main Menu: Press the MENU key once.
2. Select the Network tab > Network Source Setup. Press the RIGHT Cursor
key.
3. Select the 360 tab from the Network Source Setup dialog box.
4. Select AS 360 from the transducer list. Press the RIGHT Cursor key. A
checkmark will display in the box to show it is selected.
5. Press the EXIT key until the dialog box is closed.
Installation - Set up the Control Head
34
WARNING! The pod should NOT be in the water during high speed travel. The
pod should only be deployed when the boat is traveling between 0 to 7 mph.
2. Set the Deployment Depth
The 360 Imaging™ transducer pod should be set to deploy past the hull, propeller, and
anything else that will block the beams.
1. From the Main Menu, select the Accessories tab > 360 Sonar Settings >
360 Depth.
2. Press the RIGHT or LEFT Cursor keys to adjust the setting. (1 to 100;
Default = 8)
NOTE: The 360 Depth setting deploys the transducer in increments of 1% to 100%,
where 100% = 29 inches (73.7 cm).
3. Press the EXIT key until the menu system is closed.
Deploying the Transducer Past All Beam Obstructions
Deployment
Depth
35
Installation - Set up the Control Head
3. Test 360 Imaging™ on the Control Head
It is important to confirm that you can deploy and retract the 360 Imaging™
transducer from the control head. You should also confirm that the Transducer
Deployment System is providing sonar returns to the display.
NOTE: Before you deploy the transducer, the steps in the previous section Set up 360
Imaging™ on the Control Head must be completed.
NOTE: The instructions in this section should be performed at slow speeds (0 to 7
mph), in calm, open water, in a large area that is far from shallow water, boats, or
other obstacles.
Confirm the 360 Imaging™ Sonar Operation
1. Press the VIEW key until the 360 Imaging™ View is displayed on the screen.
The Deploy 360 Sonar dialog box will display on the screen.
Deploying from the 360 View
Installation - Set up the Control Head
36
2. Deploy: Press the RIGHT Cursor key to deploy the transducer.
3. The sonar returns from the 360 scan will begin to display on the 360 View.
Review the display for the following information:
• Bottom: Confirm that the bottom is visible on-screen.
• Blocked Beams: If the beams hit a hard surface, it will appear as bright
white on the display. If the beams are blocked by the hull, scag, trolling
motor, etc, you will need to deploy the transducer deeper (Main Menu
> Accessories tab > 360 Sonar Settings > 360 Depth).
4. Retract: When you are finished reviewing the operation, press the MENU
key once. Select Retract, and press the RIGHT Cursor key.
A
B
A Trolling Motor is obstructing the beams (the sonar returns are lighter because they hit a
hard surface)
B Bottom Return
37
Installation - Set up the Control Head
4. Confirm the Heading Sensor Operation
It is important to confirm that the Heading Sensor is installed correctly by reviewing
the heading digital readout.
NOTE: This procedure should be performed at slow speeds, in calm, open water, in a large area
that is far from shallow water, boats, or other obstacles.
1. Main Menu: Press the MENU key twice.
2. Select the Navigation tab > North Reference > Magnetic.
3. Press the EXIT key.
4. Select the Setup tab > Select Readouts.
NOTE: If the Select Readouts menu option does not appear under the Setup tab,
change the User Mode to Advanced. Select Main Menu > Setup tab > User Mode >
Advanced.
5. Select a Readout position and use the RIGHT or LEFT Cursor keys to select
Heading. Select another Readout position and select Course.
6. Press the EXIT key until the Main Menu is closed.
7. Press and hold the VIEW key. Select Sonar > Sonar View.
8. Navigate the boat in a straight line, in calm, open water at 4.5 mph. Compare
the Heading digital readout on the screen with the Course (COG) digital
readout. The readouts should be within approximately 5° of each other.
Adjust: To adjust the zero point of the Heading Sensor, select Main Menu
> Navigation tab > Heading Offset. Press the RIGHT or LEFT Cursor keys
to adjust the setting.
If the procedure failed: If the Heading digital readout is significantly
different than the COG, the Heading Sensor might be installed in a
location with too much magnetic interference. Check the installation
location and possible magnetic disturbances in the area.
Installation - Set up the Control Head
38
Confirming the Heading Digital Readout (1198c SI, Chart View)
Heading
(Heading Sensor
Required)
Course
(GPS Required)
39
Installation - Set up the Control Head
5. Confirm the Baud Rate (for devices connected to the Sensor pigtail only)
If there is an accessory, such as an autopilot, connected to the Sensor pigtail cable
wires, you will need to confirm that the devices are communicating at the same baud
rate. The baud rate details are as follows:
• If the GPS Receiver/Heading Sensor is connected to the control head, and
NMEA Output is turned on, the control head will operate exclusively at a
baud rate of 38400. If there is an accessory attached to the Sensor’s pigtail,
it also needs to operate at 38400. See your accessory installation guide to set
the baud rate to 38400.
• If NMEA Output is turned off, then baud rates 4800, 9600, and 38400 are
available on the control head and no further action is required.
Turn On/Off NMEA Output
1. Main Menu: Press the MENU key twice.
2. Select the Setup tab > NMEA Output.
3. Press the RIGHT or LEFT Cursor keys to select On or Off. (Default = Off)
NOTE: The menu option in your Fishing System will be called NMEA 0183 Output or
NMEA Output. If the menu option is not shown under the Setup tab, make sure the User
Mode is set to Advanced (Setup tab > User Mode > Advanced).
6. Set up the Network and Alarms
After you have confirmed all connections, the 360 Imaging™ transducer is ready to
use on the water. Proceed to your 360 Operations Manual to set up the depth source,
temperature source, and the 360 Imaging™ Alarms.
WARNING! If you will not be using the 360 Imaging™ Transducer on the water at this time,
continue to keep it powered while the boat is underway. This is critical to keep the pod
retracted. See Power Off for details.
Installation - Set up the Control Head
40
Power Off
The Transducer Deployment System is designed with software that keeps the pod
fully retracted and stowed while the boat is in use.
WARNING! To keep the pod retracted, the Transducer Deployment System
must stay powered ON while the boat is underway.
When the boat is stored or at dock, the Transducer Deployment System must
be turned off to prevent draining the battery. The pod cover must be installed
for trailering and storage.
1. Power off the Control Head
Press and hold the POWER/LIGHT key.
CAUTION! Turning off the control head will NOT power off the Transducer Deployment
System.
2. Power off the Transducer Deployment System
Turn off power on the main switch, breaker, or battery switch.
NOTE: Powering off the Transducer Deployment System will be determined by the
installation and power connection on your boat.
3. Install the Pod Cover
The pod cover must be installed for trailering and storage.
Install the cover over the pod. Insert the T-clips into the tracks on each side
of the Transducer Deployment System. Turn each T-clip so it stays in the track.
Tighten the straps.
41
Power Off
Maintenance
Your Humminbird® fishfinder is designed to provide years of trouble free operation
with very little maintenance. Use the following procedures to ensure your
Humminbird® continues to deliver top performance.
Control Head Maintenance
It is important to consider the following precautions when using your Humminbird®
control head:
• Chemicals, such as those found in bug spray and sunscreen, may cause
permanent damage to the control head screen. Such damage is not covered
by the warranty.
• NEVER leave the control head in a closed car or trunk. The high
temperatures generated in hot weather can damage the electronics.
Use the following information to keep the control head and screen clean.
• Screen: To clean the control head screen, use a mild soap (such as a nonabrasive liquid hand soap) and warm water. Wipe the screen dry with a soft
cloth. Be careful to avoid scratching the screen. If water spots remain, use a
solution of water and vinegar.
WARNING! Do not use a chemical glass cleaner on the screen. Chemicals in the
solution may cause cracking in the lens of the unit.
NOTE: Do not wipe the screen while dirt or grease is on the screen.
• Control Head: If the control head comes into contact with salt spray, wipe the
affected surfaces with a cloth dampened with fresh water.
Maintenance
42
Transducer Maintenance
Use the following information to maintain the transducer operation.
• If your boat remains in the water for long periods of time, algae and other
marine growth can reduce the effectiveness of the transducer. Periodically
clean the face of the transducer with a cloth dampened with fresh water.
• If your boat remains out of the water for a long period of time, it may take
some time to wet the transducer when it is returned to the water. Small air
bubbles can climb to the surface of the transducer and interfere with proper
operation. These bubbles dissipate with time, or you can wipe the face of the
transducer with your fingers after the transducer is in the water.
Transducer Deployment System Maintenance
Use the following information to maintain the installation of the Transducer
Deployment System.
• Check the tension of the 4 vertical adjustment nuts after initial use and
periodically thereafter to ensure that the installation remains stable.
• If your boat will be in long-term storage, remove the Transducer Deployment
System from the bracket and store it in –40°F to 158°F (–40°C to 70°C), dry
conditions.
• To keep the Transducer Deployment System clean, wipe the surfaces with a
cloth dampened with fresh water.
• “360 is Due for Maintenance” The 360 Imaging™ Transducer Deployment
System requires routine maintenance after 5000 deployments to ensure
continued problem-free operation and to prevent damage to the unit. A
message will display on the control head screen when 5000 deployments
have been reached.
If you receive this message on your control head, contact our Customer
Resource Center at 1-800-633-1468 to schedule maintenance.
43
Maintenance
Troubleshooting
Before contacting the Humminbird® Customer Resource Center, please read the
following section. Taking the time to review these troubleshooting guidelines may
allow you to solve a performance problem yourself, and therefore avoid sending your
unit back for repair.
Fishing System Doesn’t Power Up
If your Fishing System doesn’t power up, use the installation guide that is included
with your Fishing System to confirm specific details, making sure that:
• the power cable is properly connected to the Fishing System control head,
• the power cable is wired correctly, with red to positive battery terminal and
black to negative terminal or ground,
• the fuse is operational, and
• the battery voltage of the power connector is at least 10 Volts.
Correct any known problems, including removing corrosion from the battery terminals
or wiring, or actually replacing the battery if necessary.
Troubleshooting
44
Fishing System Defaults to Simulator with a Transducer Attached
In addition to the 360 Imaging™ accessory transducer, you will have a standard
Humminbird® transducer connected to the control head. A connected and functioning
transducer will cause the newly-started Fishing System to go into Normal operating
mode automatically. If, when you power up the Fishing System, it goes into Simulator
mode automatically, even though a transducer is already connected, this means that
the control head is not detecting the transducer. Perform the following
troubleshooting tasks:
• Check the connections of all transducers that are connected to the control
head or Ethernet network. See the transducer installation guide that was
included with your Fishing System for connection information.
• Review this 360 Imaging™ installation guide to confirm that the transducer
cable is connected correctly to the Fishing System. Reconnect if necessary,
and power on the Fishing System again to see if this fixes the problem.
• Because the 360 Imaging™ transducer is on the network, it might take up to
a minute to be detected on the network. Use the 4-WAY Cursor Control key
to select Normal from the Start-Up Options Menu. In this guide, see Set up
the Control Head, Section 1. Power on and Confirm Connections.
• Replace the non-functioning transducer with a known good transducer if
available and power up the control head again.
• Check the transducer cable. Replace the transducer if the cable is damaged
or corroded.
45
Troubleshooting
The Pod Doesn’t Deploy or Retract
If the pod won’t retract through the control head or through the Transducer
Deployment System keys, it can be retracted manually. You can also reboot the
system if the pod is not deploying or retracting from the control head commands.
CAUTION! Check for obstructions around the unit that might be blocking the pod from
deploying or retracting.
• If the pod won’t retract through the control head or through the Transducer
Deployment System —key, it can be retracted manually. Place your hand
under the base of the pod and carefully push it up, into the Transducer
Deployment System.
• If the pod will not remain retracted, remove the Transducer Deployment
System from the transducer bracket and store it on the boat.
• If the pod will not deploy or retract, power off the control head. Then, unplug the
power cable from the power port on the Transducer Deployment System. Wait
10 seconds, and then reconnect the power cable and restart the control head.
Troubleshooting
46
Finding the Cause of Noise
Electrical noise usually affects the display with streaks or repetitive patterns on the
view. One or more of the following sources can cause noise or interference:
Possible Source of Noise
Isolation
Other electronic devices
Turn off any nearby electronic devices to see if the
problem goes away, then turn them on one at a time
to see if the noise re-appears.
The boat’s engine
To determine whether the boat’s engine is the source
of the noise, increase the RPMs while the boat is in
neutral and stationary to see if the noise increases
proportionately; if noise appears when you rev the
engine, the problem could be the spark plugs,
alternator, or tachometer wiring. Replace the spark
plugs with resistor plugs, install an alternator filter,
or route the control head power and transducer
cables away from the engine wiring.
Cavitation from the boat’s propeller
Turbulence created by the propeller can cause noise;
make sure the transducer is mounted at least 6”
(15.24 cm) from the propeller, and that the water
flows smoothly over the face of the transducer at all
times.
47
Troubleshooting
Removing the Pod (for authorized repair only)
Use the following instructions to remove the pod and send it to Humminbird® for
service.
WARNING! Do NOT remove the pod unless you have a repair authorization number from
our Customer Resource Center. Removing the pod without authorization will void the
warranty. See the Warranty and Service Policy for details.
NOTE: Place a table under the Transducer Deployment System so you have a surface to
support the removal of hardware as you work, or you might prefer to remove the Transducer
Deployment System from the transducer bracket and place it on a stable surface to work.
1. Contact the Customer Resource Department at service@humminbird.com
or 1-800-633-1468 to request a Repair Authorization Number.
2. Disconnect the power cable from the Transducer Deployment System.
3. Place your hands above the pod and pull down the deployment column, so
the pod is deployed approximately 6” (15 cm).
4. Hold the pod from the bottom so it is supported, and remove the two screws
from the top of the pod (see the illustration Removing the Screws).
Pulling Down the
Deployment Column
Removing the Pod (for authorized repair only)
Removing the
Screws
48
5. Place a small screwdriver through the
Deployment System. See the illustration
Removing the Fasteners from the
Connector Case.
Removing the Fasteners
from the Connector Case
CAUTION! If the cables retract into the
deployment system, pull the cables carefully
back down. Do NOT pull the cables down by the
connectors or wires.
6. Remove the fasteners from the
connector case. See the illustration
Removing the Fasteners from the
Connector Case.
7. Use a flat-head screwdriver to press
inward, on the top of each connector
tab, to disengage the latch. You can also
use the screwdriver to carefully pry the
connectors out of the ports. See
the illustration Disconnecting the
Connectors.
Remove
the
fasteners
Connector
Case
Disconnecting the Connectors
CAUTION! Be careful not to damage the tabs
or pull on the wires while you are disconnecting
the connectors.
Press
inward
49
Removing the Pod (for authorized repair only)
Checking the Pins
Connector 1
All pins must
be populated,
except for this
center pin.
Connector 2
8. Compare the pins in the connectors with the illustration Checking the Pins to
confirm they’ve stayed in place.
If the pins have remained installed, proceed to the next step.
If the pins have been pulled out of the connectors, you will need to send
the full Transducer Deployment System. If this is the case, call our Customer
Resource Center at 1-800-633-1468.
9. Place the pod in a sealed plastic bag to prevent leaking. Pad the package as
needed so the pod is secure and protected during shipment.
Also, save any loose parts that were removed; you will need them to
reconnect the pod.
10. Wrap the connectors on the Transducer Deployment System with plastic
wrap (or a similar material) to protect them from potential environmental
damage (water, dust, etc.).
Removing the Pod (for authorized repair only)
50
Reconnecting the Pod (for authorized repair only)
If the transducer pod has been serviced by our Customer Resource Center, follow the
steps in this section to reconnect the pod. See the illustration Reconnecting the Pod
for more information.
WARNING! Make sure that power is disconnected from the Transducer Deployment
System before you start the reconnection instructions.
1. Place a small screwdriver into the deployment column holes so that the
cables don’t retract into the Transducer Deployment System. See the
illustration Removing the Fasteners from the Connector Case in the
previous section for more information.
CAUTION! If the cables retract into the deployment system, pull the cables carefully
back down. Do NOT pull the cables down by the connectors or wires.
2. Look inside the pod and confirm the hex standoff is in place. See the illustration,
Confirming the Hex Standoff Installation. If it has fallen out, insert a new hex
standoff from the provided repair installation kit.
Confirming the Hex Standoff Installation
Hex Standoff
in the Center
51
Reconnecting the Pod (for authorized repair only)
3. Place the gasket onto the Connector Case base.
4. Line up the connectors with the ports so that the tabs are on the outside of
each connector.
WARNING! Look up inside the Connector Case top. There is a Printed Circuit Board
(PCB) between the connectors. Make sure that it stays lined up between the
connectors, and that it doesn’t get jammed, when the case is refastened in the
proceeding steps.
5. Insert the connectors into the ports. Push them in until the tabs click or the
connectors are fully seated in the ports.
CAUTION! Be careful not to break the tabs or pull on the wires while you are inserting the connectors into the ports.
6. Close the connector case and install the new fasteners and hex standoffs.
Tighten them to the recommended torque of 5 in/lbs.
7. Carefully slide the pod onto the deployment column, inserting the cables and
connector case into the deployment column, and supporting the pod from the
base.
8. Align the holes of the transducer pod with the holes on the Deployment
Column. You might have to apply pressure to align the holes.
9. Install the new screws at the top of the pod. Hand-tighten only.
10. Reconnect the power cable to the Transducer Deployment System port.
When power is detected, the pod will retract automatically. The detection
may take up to 2 minutes.
Reconnecting the Pod (for authorized repair only)
52
Reconnecting the Pod
Deployment
Column
Hole(s)
Fastener(s)
Connector
Case (Top)
Connectors
with PCB
in between
them
Gasket
Connector
Ports
Connector
Case (Base)
Hex
Standoffs
Screw(s)
Pod
53
Reconnecting the Pod (for authorized repair only)
Specifications
Deployment Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 inches
Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455 kHz
Area of Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455 kHz: (2) 90° @ -10 dB
Target Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1/2 inches (63.5 mm)
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 Watts (RMS),
4000 Watts (Peak to Peak)
Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 to 20 VDC
Current Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 mA average (operating)
4 A maximum (deploying/retracting)
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . 32°F to 158°F (0°C to 70°C)
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . –40°F to 158°F (–40°C to 70°C)
NOTE: Humminbird® verifies maximum stated depth in saltwater conditions, but actual
depth performance may vary due to transducer installation, water type, thermal layers,
bottom composition and slope.
NOTE: Product specifications and features are subject to change without notice.
Specifications
54
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Johnson Outdoors
Marine Electronics, Inc. to be a responsible corporate citizen, operating in compliance with
known and applicable environmental regulations, and a good neighbor in the communities
where we make or sell our products.
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment
Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer
electronics in the European Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from their products to
achieve environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment
(EEE), nor may it be required for EEE designed and intended as fixed or temporary
installation in transportation vehicles such as automobiles, aircraft, and boats. In some
European Union member states, these vehicles are considered outside of the scope of the
Directive, and EEE for those applications can be considered excluded from the WEEE
Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be
disposed of with other household refuse. It must be disposed of and collected for
recycling and recovery of waste EEE. Johnson Outdoors Marine Electronics, Inc.
will mark all EEE products in accordance with the WEEE Directive. It is our goal to
comply in the collection, treatment, recovery, and environmentally sound disposal of those
products; however, these requirements do vary within European Union member states. For
more information about where you should dispose of your waste equipment for recycling
and recovery and/or your European Union member state requirements, please contact your
dealer or distributor from which your product was purchased.
55
Specifications
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone:
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail:
(typically we respond to your e-mail within three business days):
service@humminbird.com
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising