VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86

DATA PROJECTOR

VPL-CX61

VPL-CX63

VPL-CX75

VPL-CX76

VPL-CX80

VPL-CX85

VPL-CX86

VPL-FX51

VPL-FX52

VPL-FX52L

VPL-PX35

VPL-PX40

VPL-PX41

PROTOCOL MANUAL

1st Edition (Revised 9)

! WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

! WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.

! AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Table of Contents

1.

Introduction Appendix A.

Setup Method For VPL-PX35 and PX40

2.

RS-232C (VPL-CX75 and

VPL-CX76 are excluded.)

2-1.

Communication Specifications .......................................... 1

2-2.

Command Block Format .................................................... 2

2-3.

Block Format ..................................................................... 3

2-4.

Connection ......................................................................... 4

2-5.

Communication Procedure ................................................ 4

2-5-1.

Outline of Communication ....................................... 4

2-6.

Communication Rules ....................................................... 5

2-7.

Approximate Return Waiting Times ................................. 5

A-1. Command ......................................................................... 18

A-1-1.

Setting ..................................................................... 18

A-1-2.

Display ................................................................... 19

A-2. Setting Command ............................................................ 20

Appendix B

3.

NETWORK

3-1.

Introduction ........................................................................ 6

3-1-1.

Advertisement .......................................................... 6

3-1-1-1.

Function ................................................................. 6

3-1-1-2.

Setup Items ............................................................ 6

3-1-2.

Remote Control ........................................................ 7

3-1-2-1.

Function ................................................................. 7

3-1-2-2.

Setup Items ............................................................ 7

3-2.

SDAP Protocol ................................................................... 8

3-3.

SDCP Protocol ................................................................... 9

3-3-1.

Format ...................................................................... 9

3-3-1-1.

Header ................................................................... 9

3-3-1-2.

Community ............................................................ 9

3-3-1-3.

Command ............................................................ 10

3-3-1-4.

SET Request ........................................................ 11

3-3-1-5.

GET Request ....................................................... 11

3-3-1-6.

ERROR Response ............................................... 11

3-3-2.

Items ....................................................................... 12

3-3-2-1.

Model Dependent Category ................................ 12

3-3-2-2.

Equipment Information Acquisition (80**h) ...... 12

3-3-2-3.

Network Information Acquisition (90**h) ......... 13

3-3-3.

Error Code .............................................................. 14

3-3-3-1.

Item Error ............................................................ 15

3-3-3-2.

Community Error ................................................ 15

3-3-3-3.

Request Error ...................................................... 16

3-3-3-4.

Network Error ..................................................... 16

3-3-3-5.

Comm Error ........................................................ 17

3-3-3-6.

NVRAM Error .................................................... 17

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

1

1. Introduction

This protocol manual describes the basic configuration and basic operations of various commands used for projector. Projector can be controlled using the commands provided in “Appendix”. Using an external

CONTROLLER , etc., inputs can be switched and the power can also be turned on and off. In the following paragraphs, “CONTROLLER” means an external device such as a PC which controls projector using these commands.

2. RS-232C (VPL-CX75 and VPL-CX76 are excluded.)

2-1. Communication Specifications

<RS-232C Communication Signal>

. Full duplex communication channels (Flow control not performed.)

. Start-stop synchronism system

. Baud rate: 38.4 kbps (bits per second)

. The bit configuration is defined as follows.

1 START Bit

+ 8 DATA Bits + 1 PARITY Bit + 1 STOP Bit

START

BIT

D0

(LSB)

D1 D2 D3 D4 D5 D6 D7

(MSB)

PARITY STOP

(EVEN) BIT

EVEN Parity.....Total number of “1”s from D0 to D7 is an even number.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

1

B3

B4

B5

B6

B7

B0

B1

B2

2-2. Command Block Format

The code from B0 to B7 as described below are transmitted.

Transmission from the Master side

ITEM NUMBER

SET / GET

DATA

Reception in the Master side

START CODE : 0 x A9

ACK / NAK

ACK

DUMMY DATA

CHECK SUM

END CODE : 0 x 9A

B0 START CORD

Common in the all FORMAT

B6 CHECK SUM

B1 to B5 are calculated by OR;

<Example of Calculation>

0 x A9

0 x A9

Answer

1010

1010

1010

1001

1001

1001

0 x A9

B7 END CODE

Common in the all FORMAT

0 x A9

0 x 9A

Answer

1010

1001

1011

Reception in the Master side

(With Data)

1001

1010

1011

0 x BB

ITEM NUMBER

REPLY

DATA

2

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

2-3. Block Format

B0

B1

B2

B3

B4

B5

B6

B7

B0

B1

B2

B3

B4

B5

B6

B7

Transmission from the Master side

START CODE

ITEM NUMBER

SET / GET

DATA

CHECK SUM

END CODE

Reception in the Master side

START CODE

ACK / NAK

ACK

DUMMY DATA

CHECK SUM

END CODE

Data transmission to the Projector

Start of Command

Set the Data Category Value desired.

Refer to the Appendix B Table 1 for details.

SET: 0 x 00 (Set data)

GET: 0 x 01 (Get data)

SET: Data to be set (Refer to the Appendix B Table 2)

GET: Unused. Set Dummy data [0 x 00, 0 x 00]

Check Sum

End of Command

Receive results of the data transmission from the Projector.

Start of Command

Results correspond with the data transmission

Refer to the Appendix B Table 3 for the data in detail.

[0 x 03]

Express Reply data either of ACK, or NAK

This data does not mean any senses.

Dummy Data [0 x 00, 0 x 00] is stored.

Check Sum

End of Command

B0

B1

B2

B3

B4

B5

B6

B7

Reception in the Master side (With Data)

START CODE

ITEM NUMBER

REPLY

DATA

CHECK SUM

END CODE

Receive data from the Projector

Start of Command

Data to acquire

Refer to the Appendix B Table 1 in detail.

[0 x 02]

Express data to be Reply data

Received data

Refer to the Appendix B Table 2 in detail.

Check Sum

End of Command

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3

2-4. Connection

<RS-232C Connection>

Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable.

The pin assignment of D-Sub 9 Pin and D-Sub 25 Pin is as follows.

D-Sub 9 Pin

Shell = FG

3

2

7

8

6

4

9

5

1

D-Sub 25 Pin

1

2

3

4

5

6

7

8

20

22

FG

TxD

RxD

RTS

CTS

DSR

SG

DCD

DTR

RI

Name

Grounding for safety protection or cable shield

Transmission data

Reception data

Transmission request

Transmission permission

Data set ready

GND for signal

Data channel signal carrier detection

Data terminal ready

Calling display (Presence/absence of calling signal)

Pins indicated as D-Sub 25 Pin are not used.

Assured cable length: 15 m (However, assurance may not be applicable for some cables.)

The software for controlling the projector from a PC is intended for performing transmission and reception for only the TxD and RxD lines.

Therefore there is no handshake normally performed by RS-232C.

2-5. Communication Procedure

2-5-1. Outline of Communication

All communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR) is performed by the command block format. Communication is started by the issue of a command at CONTROLLER and ended when the return Data is sent to CONTROLLER after DEVICE receives the command.

CONTROLLER is prohibited from sending several commands at one time. This means that after CON-

TROLLER sends one command, it cannot send other commands until DEVICE returns the return Data.

DEVICE sends the return Data after processing the command. The time from when CONTROLLER sends the command until the return Data is returned differs according to the contents of the command.

n

When Sircs Direct Command is sent, return Data may not be returned in some cases.

4

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

2-6. Communication Rules

. When sending a command from CONTROLLER, the return Data from PROJECTOR should be received first before sending the next command. Even if the next command is sent before receiving the return Data, since PROJECTOR will not be able to receive that command, it does not return a response to CONTROLLER. Consequently, no error code is also sent.

The following lists the approximate waiting times for PROJECTOR to return the return Data after

CONTROLLER sends the command.

. When a communication error occurs, PROJECTOR ignores the Data received until now, and set into the reception standby state.

. For undefined commands or commends determined as invalid by PROJECTOR, PROJECTOR will send the “NAK” return Data to CONTROLLER .

. Take note that when Data is written when the input signal of PROJECTOR is unstable, that Data

(value) will not be incorporated.

. When INDEX specified SIRCS direct command is transmitted, leave an interval of 45 msec until the next transmission. (Do not return the return Data (ACK, NAK) when the SIRCS direct command is received.)

2-7. Approximate Return Waiting Times

The await-return time is approx. 30 msec.

n

This is the case, unless the communications are interfered anyway.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

5

3.

NETWORK

3-1. Introduction

This section describes the specifications, performance and operations of the network service that is going to be installed in the target projector.

3-1-1. Advertisement

The advertisement service is provided to facilitate development of a PC application that can automatically detect a projector on the network. This function is achieved by broadcasting the equipment information periodically to the network.

3-1-1-1. Function

The equipment information shown below is transmitted as the broadcast packet periodically (at certain intervals).

Information

Category

Equipment name

Serial number

Installation information

Community

Power status

Description

Category of the equipment

Name of the equipment

Serial number of the equipment

Installation location of the equipment

Community name of the equipment

Power status of the equipment m

. The category of projector is 0x0a.

. The power status sets ffffh if communication error occurs.

Protocol

The SDAP protocol is defined in order to provide this service.

Item

Protocol name

Transport

Port number

BC interval

Description

SDAP (Simple Display Advertisement Protocol)

UDP

53862

Once every 30 seconds (initial value)

3-1-1-2. Setup Items

The items that can be set for the advertisement service are described below.

Setup items

Port

Interval

Description

Port number

Broadcast interval

6

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-1-2. Remote Control

The remote control service is provided that can control the target equipment from remote location via network. The SDCP protocol that serves to acquire the basic information such as equipment name and serial numbers is installed in this projector.

3-1-2-1. Function

This responds to the control command and requests for acquiring the status and information supplied from clients.

Control request

Enables the input to be selected and picture control to be adjusted.

SIRCS request

Enables remote control by sending the SIRCS code.

Status request

Enables equipment status information such as power status, error information and power-on time to be acquired.

Information request

Enables equipment information such as equipment name, serial number and installation information to be acquired.

Protocol

Item

Protocol name

Transport

Port number

TCP connection timeout

Description

SDCP (Simple Display Control Protocol)

TCP

53484

30 seconds

3-1-2-2. Setup Items

The items that can be set for the remote control service are described below.

Setup item

Port

Timeout

Description

Port number

TCP connection timeout time

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

7

3-2. SDAP Protocol

This section describes the SDAP packet structure.

Header

(4)

Community

(4)

Product name

(12)

Serial No.

(4)

Power

Status

(2)

Fig.1 Packet structure

Location

(24)

1) Header

The header consists of ID (16 bit), version (8 bit) and category (8 bits).

0 1 2 3

0

4 5 6 7 8

“DA” (16)

9

1

0 1 2 3 4 5 6 7

2

8 9 0 1 2 3

Version (8)

Fig. 2 Header

4 5

3

6 7 8 9 0 1

(Bit position)

Category (8)

ID

It is fixed to “DA”.

Version

This indicates the version number of protocol.

It is fixed to 01h (version 1).

Category

Category number 0x0a of the projector is entered here.

2) Community

The community that is set in the display equipment is entered. Community consists of four alphanumeric characters (case sensitive). The display equipment has the default value “SONY” when shipped from the factory.

0 1 2 3

(Bit position)

0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1

Community (32)

Fig. 3 Community

3) Equipment Information

Product Name

Name of equipment (Maximum twelve characters)

In case, less than twelve characters, 00h is entered in the blank space.

Serial No.

Serial number is entered.

Power Status.

Power supply status of the equipment is entered.

Location

Information of installation location (Maximum twenty four characters)

In case, less than twenty four characters, 00h is entered in the blank space.

8

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-3. SDCP Protocol

This section describes the packet structure of SDCP.

Header

(2)

Community

(4)

Command

(4)

Data (n)

Fig. 1 Packet structure

3-3-1. Format

3-3-1-1. Header

The header consists of Version (8 bits) and Category (8 bits).

0 1

0

2 3 4 5 6 7

Version (8)

8 9

1

0 1 2 3 4 5

Category (8)

(Bit position)

Fig. 2 Header structure

Version

This indicates the version number of protocol.

It is fixed to 02h (version 2).

Category

Category number 0x0a of the projector is entered here. Projector checks the category number. If a different category number is entered, the request is ignored.

3-3-1-2. Community

When the community Data matches the community that is set in the display equipment, the request is executed. Community consists of four alphanumeric characters (case sensitive). All display equipment has the default value “SONY” when shipped from the factory.

0 1

0

2 3 4 5 6 7 8 9

1

0 1 2 3 4 5 6 7

2

8 9 0 1 2 3 4 5

3

6 7 8 9 0 1

(Bit position)

Community (32) n

Community should be entered with four characters. Three characters or less are not accepted.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

9

3-3-1-3. Command

This section describes the format of the request command and the response command.

0 1 2 3

0

4 5 6

Request/Response (8)

7 8 9 0 1

1

2 3 4 5 6 7

Item No (16)

2

8 9 0 1 2 3 4 5

3

6 7 8 9 0 1

(Bit position)

Data Length (8)

(1) Request

This section describes the format of the request command that is issued from the host PC to the projector.

Community

This is the same alphanumeric characters as those of community that is set in the projector to which request is going to be sent.

Request

There are only two types of request. One is the GET request to acquire the projector information and status. The other is the SET request to modify the projector setup.

Request Contents

SET (00h) Used to control turning the power on/off and to control the input selector, and to change the various setups.

SET (01h) Used to acquire the installation information, equipment status and various setup values.

Item No.

This is the item number of the request target.

Data Length

This is the length of the Data accompanying the request. The maximum length is 128 bytes. If there is no

Data, it is 0.

Data

This is the Data accompanying the request.

(2) Response

This section describes the format of the response command which is used to return a response to the host

PC from the projector.

Community

The same alphanumeric characters as those of the request is entered.

Response

The response returns the result of executing the request from the host PC.

Response

NG (00h)

OK (01h)

Contents

Indicates that the request is illegal or cannot be executed.

Indicates that the request was executed correctly.

Item No.

The same value as those of the request is entered.

Data Length

This is the length of the Data accompanying the response. The maximum length is 128 bytes. If there is no Data, it is 0.

Data

This is the Data accompanying the response.

10

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-3-1-4. SET Request

The SET request is used to set a new value in the specified item. Details of the request and the response are described below.

Request

Request

00h

Item No.

Item No.

Data

Length n

Data

Set Data (n byte)

Response

OK (01h) Item No.

0

3-3-1-5. GET Request

The GET request is used to acquire the value of the specified item. Details of the request and the response are described below.

Request

Request

01h

Item No.

Item No.

Data

Length

0

Response

OK (01h) Item No.

n Get Data (n byte)

3-3-1-6. ERROR Response

When an error occurs in the contents of a request or in the result of execution, NG is returned as the response.

NG (00h) Item No.

2 Error Code (16)

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

11

3-3-2. Items

Category

00**h

01**h

03**h

17**h

19**h

80**h

90**h

Contents

Used to control and to change the various setups.

Used to acquire the status.

Used to reset memory.

Sircs (15 bit category)

Sircs (20 bit category)

Used to acquire equipment information.

Used to acquire network setup information.

SET

O

O

O

O

3-3-2-1. Model Dependent Category

The supported contents of 00

**h, 01**h, 03**h, 17**h and 19**h change depending on the model.

Details are shown on Appendix.

3-3-2-2. Equipment Information Acquisition (80**h)

Used to acquire the equipment information.

Lower byte

00h

01h

02h

03h

Contents

Category Code

Model name

Serial number

Installation location

SET

O

GET

O

O

O

O

GET

O

O

O

O

0x8000 Category code

1 byte

0x8001 Model name

Alphanumeric 12 characters

If the number of characters is less than 12, the remaining digits are filled with 00h.

0x8002 Serial number

4 bytes n

The serial number is in the range of 00000000 to 99999999.

0x8003 Installation location

Alphanumeric 24 characters

If the number of characters is less than 24, the remaining digits are filled with 00h.

12

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-3-2-3. Network Information Acquisition (90**h)

Used to acquire the network setup information.

Lower bytes

00h

01h

02h

03h

04h

Contents

MAC Address

IP Address

Subnet Mask

Default Gateway

DHCP

0x9000 Mac Address

6 bytes

0x9001 IP Address

4 bytes

0x9002 Subnet Mask

4 bytes

0x9003 Default Mask

4 bytes

0x9004 DHCP

1 byte

DHCP invalid : 0

DHCP valid : 1

SET GET

O

O

O

O

O

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

13

3-3-3. Error Code

The error code list is shown below with a detailed description of each.

Category Error Error Code

Item Error (01**h)

Community Error (02**h)

Request Error (10**h)

Network Error (20**h)

Comm Error (F0**h)

NVRAM Error (F1**h)

Invalid Item

Invalid Item Request

Invalid Length

Invalid Data

Short Data

Not Applicable Item

Different Community

Invalid Version

Invalid Category

Invalid Request

Short Header

Short Community

Short Command

Timeout

Timeout

Check Sum Error

Framing Error

Parity Error

Over Run Error

Other Comm Error

Unknown Response

Read Error

Write Error

01h

02h

03h

04h

11h

80h

01h

01h

02h

03h

11h

12h

13h

01h

01h

10h

20h

30h

40h

50h

F0h

10h

20h

14

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-3-3-1. Item Error

This error occurs when the Item No. of a request is illegal or its Data is illegal. The conditions for occurrence of the respective errors are shown below.

Invalid Item

An unsupported Item No. is specified.

Example 1: The unsupported category 0xA

** is specified.

Example 2: The unsupported Item No. 0x8010 is specified.

Invalid Item Request

The Item No. is supported but an unsupported Request is issued.

Example: An attempt is made to set Data in the Model Name (0x8001).

Invalid Length

Data Length of the specified Item No. is too long.

Example: An attempt is made to set 25 byte Data in the installation location (0x8003).

Invalid Data

Data of the specified Item No. is outside the setting range.

Example: An attempt is made to set 101 in the Item when the setting range of the Item is 1 to 100.

Short Data

The length of Data is shorter than the value specified by the Data Length.

Example: The actual Data length is 9 bytes but Data Length is 10.

Not Applicable Item

An item that is not valid at present is specified.

Example: The item to switch the display is specified when the main power is off.

3-3-3-2. Community Error

This error occurs when community is different.

Example: “ABCD” is specified when “SONY” is set.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

15

3-3-3-3. Request Error

This error occurs when Header or Command is illegal. The conditions of occurrence of the respective errors are shown below.

Invalid Version

The version of the Header is other than 2.

n

When another version is supported, an error occurs in all versions other than the supported version.

Invalid Category

The category does not match.

Example: 0x0B is specified in the device of Category = 0x0A.

Invalid Request

An unsupported request is specified.

Example: Request = 0x02 is specified.

Short Header

The received Data is 1 byte.

Short Community

The received Data is in the range of 2 to 5 bytes.

Short Command

The received Data is in the range of 6 to 9 bytes.

3-3-3-4. Network Error

This is an error that occurs in TCP/IP. The conditions of occurrence of the respective errors are shown below.

Timeout

Communication was interrupted.

16

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

3-3-3-5. Comm Error

This is an error in communication with the main control microprocessor of the display.

Timeout

Reception Data is not returned after Data is sent.

Check Sum Error

A check sum error occurred in the main control microprocessor of the display.

Framing Error

A framing error occurred.

Parity Error

A parity error occurred.

Over Run Error

An overrun error occurred.

Other Comm Error

Another error occurred.

Unknown Response

The Data cannot be processed was received.

3-3-3-6. NVRAM Error

Read Error

Reading from NVRAM was failed.

Write Error

Writing to NVRAM was failed.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

17

Appendix A.

Setup Method For VPL-PX35 and PX40

Establishing the network setup such as IP address can be implemented from the PC browser, and the information such as installation location can be viewed on the PC browser.

A-1. Command

A-1-1. Setting

Enter the following command using the format shown below in a browser as URL, and then the simple response is returned.

Format

http://IP address/Item?Value

IP address

Item

Value

The IP address that is assigned to the network block

Name of the setup item

Setting value

Response

The following HTML is returned that enables to confirm OK or NG simply.

<HTML>

<TITLE>

IP address

</TITLE>

<BODY>

&lt; Equipment name: Serial number&gt;<BR><BR>

Result [Item = Value]

</BODY>

</HTML>

IP address The IP address that is assigned to the network block

Equipment name Name of the equipment in which setup is implemented

Serial number

Result

Serial number of the equipment in which setup is implemented

Result (OK or NG) is displayed.

Item

Value

Name of the setup item

Setting value

18

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

A-1-2. Display

Enter the following command using the format shown below in a browser as URL, and then value of the setting item is displayed.

Format

http://IP address/Item

IP address

Item

The IP address that is assigned to the network block

Name of the setup item

Response

The following HTML is returned.

<HTML>

<TITLE>

IP address

</TITLE>

<BODY>

&lt; Equipment name: Serial number&gt;<BR><BR>

Result [Item = Value]

</BODY>

</HTML>

IP address The IP address that is assigned to the network block

Equipment name Name of the equipment that has acquired the setup value

Serial number

Result

Serial number of the equipment that has acquired the setup value

Result (OK or NG) is displayed.

Item

Value

Name of the setup item

Setting value

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

19

A-2. Setting Command

Each setting item is described below.

Equipment information

Item

location

Community

Description Default

Sets location of the equipment installation. (Maximum 24 alphanumeric characters) _

Sets the equipment community. (Maximum 4 alphanumeric characters) SONY n

Location and community do not support Japanese character.

Network setup

Item

dhcp ipaddr subnet gateway restart

Description

Specifies method of setting IP address.

IP address

Subnet mask

Default gateway

Restarts the network block to make the network setup effective.

Default

No

192.168.0.1

255.255.0.0

0.0.0.0

m

. When the network setup is changed, execute restart to make the setup effective.

. For the setup of dhcp, set 1 to make DHCP effective and set 0 to make DHCP ineffective.

Service setup

Item

ad_port ad_interval ad_ip rc_port rc_timeout

Description

Port number of the Advertisement service

Broadcast interval of the Advertisement service (in units of second)

IP address of the Advertisement service

Port number of the Remote Control service

TCP connection timeout time of the Remote Control service (in units of second)

Default

53862

30 (seconds)

0.0.0.0

53484

30 (seconds) m

. When network setup is changed, executing restart is required to make the network setup effective.

. When ad_Interval value is set to 0, the advertisement service is stopped.

. The ad_Interval can be set to 0 or a value in the range of 10 to 65535.

. The rc_timeout can be set to a value in the range of 0 to 65535.

20

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Appendix B

Item

INPUT

CONTRAST

BRIGHTNESS

COLOR

HUE

SHARPNESS

RGB ENHANCER

COL TEMP

DDE

ASPECT

SCAN CONV

PICTURE MUTING

INPUT A

LAMP MODE

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

STATUS ERROR

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

01h

Lower byte

01h

10h

11h

12h

13h

14h

15h

17h

18h

20h

21h

30h

32h

40h

80h

81h

82h

83h

84h

85h

01h

(VPL-FX51)

<Table 2>

Data

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

Data

VIDEO

S VIDEO

INPUT A

INPUT B

INPUT C

Setting value (0 to 100)

Setting value (0 to 100)

Setting value (0 to 100)

Setting value (0 to 100)

Setting value (0 to 100)

Setting value (0 to 100)

LOW

HIGH

OFF

PROGRESSIVE

FILM

16 : 9

4 : 3

OFF

ON

OFF

ON

COMPUTER

COMPONENT

VIDEO GBR

HIGH

STANDARD

Setting value (0 to 255)

Setting value (0 to 255)

Setting value (0 to 255)

Setting value (0 to 255)

Setting value (0 to 255)

Setting value (0 to 255)

NO ERROR

LAMP ERROR

FAN ERROR

COVER ERROR

TEMP ERROR

D5V ERROR

POWER ERROR

WARNING ERROR

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Remarks

00h

01h

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

01h

00h

01h

02h

01h

00h

01h

00h

08h

10h

20h

40h

00h

01h

02h

04h

Lower byte

00h

01h

02h

03h

04h

00h to 64h

00h to 64h

00h to 64h

00h to 64h

00h to 64h

00h to 64h

00h

01h

00h

01h

02h

00h

Set/Get

Get only

21

(VPL-FX51)

<Table 1> <Table 2>

Item

STATUS POWER

CONTROL MODE SEL

Item Number

Upper byte

01h

01h

Lower byte

02h

05h

Data

STANBY

START UP

STARTUP LAMP

POWER ON

COOLING1

COOLING2

SAVING COOLING1

SAVING COOLING2

SAVING STABY

USER

SERVICE

USE TIME

MAIN ROM VERSION

SC ROM VERSION

LAMP TIMER

ROM VERSION

SC ROM VERSION

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

01h

01h

01h

03h

13h

1Dh

1Eh

01h

02h

03h

04h

00h

W/B Low Save

W/B High Save

05h

06h

Sircs (15bit category) 17h Refer to table 4 _ 00h

Sircs (20bit category) 19h Refer to table 5 _

*1Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.

*2Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3It is corresponded to single command only.

00h

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

0000h-ffffh *1

*2

Lower byte

00h

01h

02h

03h

04h

05h

06h

07h

08h

00h

01h

*2

00h

00h

00h

Remarks

Get only

Set only

Set only *3

Item

ACK

NAK

(VPL-FX51)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

Data

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

Approximate Return Waiting Times

The await-return time is approx. 50 msec.

n

This is the case, unless the communications are interfered anyway.

22

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

RGB Enhancer

ColTemp

DDE

Wide Mode

Scan Conv

Picture Muting

Input-C Signal Sel

Lamp Mode

Gain Red

Gain Green

Gain Blue

Bias Red

Bias Green

Bias Blue

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

10h

11h

12h

13h

14h

15h

17h

(VPL-FX52/FX52L)

Lower byte

01h

02h

18h

20h

21h

30h

32h

40h

80h

81h

82h

83h

84h

85h

<Table 2>

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Data

Video

S-Video

Input-A

Input-B

Input-C

Dynamic

Standard

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

High

Low

Off

Progressive

Film

Off

On

Off

On

Off

On

Computer

Component

Video GBR

High

Standard

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Remarks

00h to 64h

00h to 64h

00h to 64h

00h

01h

00h

01h

02h

00h

01h

00h

01h

Lower byte

00h

01h

02h

03h

04h

00h

01h

00h to 64h

00h to 64h

00h to 64h

00h

01h

00h

01h

02h

00h

01h

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

23

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B High Save

W/B Low Save

Sircs (15 bit category)

Sircs (20 bit category)

24

Item

Status Error

Status Power

Control Mode Select

Lamp Timer

ROM Version

SC ROM Version

Status Security *3

Item

ACK

NAK

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

03h

17h

19h

(VPL-FX52/FX52L)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

(VPL-FX52/FX52L)

Lower byte

01h

02h

05h

13h

1Dh

1Eh

1Fh

Data

No Error

Lamp Error

Fan Error

Cover Error

Temp Error

D5V Error

Power Error

Warning Error

Stanby

Start Up

Start Up Lamp

Power On

Cooling1

Cooling2

Saving Cooling1

Saving Cooling2

Saving Staby

User Mode

Service Mode

Lamp Use Time

MAIN ROM Version

SC ROM Version

Disable

Enable

_

<Table 2>

Data

Upper byte Lower byte

00h

00h

00h

01h

00h

00h

00h

02h

04h

08h

00h

00h

00h

00h

00h

00h

00h

10h

20h

40h

00h

01h

02h

03h

00h

00h

00h

00h

00h

00h

08h

00h

00h 01h

0000h-FFFFh

*1

*2

04h

05h

06h

07h

00h

00h

00h

*2

00h

01h

00h 01h

02h

03h

04h

05h

06h

Refer to table 6

Refer to table 7

Data

Remarks

Get only

Set only

_

_

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

00h

00h

00h

00h

Set only

*4

*1 Example) In case the lamp timer indicates

1000H, return values are [03h] upper byte and

[E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

Approximate Return Waiting Times

The await-return time is approx. 50 msec.

n

This is the case, unless the communications are interfered anyway.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

RGB Enhancer

Volume

ColTemp

DDE

Wide Mode

Scan Conv

Picture Muting

Audio Muting

Input-D Signal Sel

Lamp Mode

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

<Table 1>

Item Number

Upper byte

00h

10h

11h

12h

13h

14h

15h

16h

17h

(VPL-PX35, PX40, PX41)

Lower byte

01h

02h

18h

20h

21h

30h

31h

33h

40h

80h

81h

82h

83h

84h

85h

<Table 2>

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Data

Video

S-Video

Input-A

Input-B

Input-C

Input-D

Dynamic

Standard

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

High

Low

Off

Progressive

Film

Off

On

Off

On

Off

On

Off

On

Computer

Component

Video GBR

High

Standard

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Remarks

00h to 64h

00h to 64h

00h to 64h

00h to 64h

00h to 64h

00h

01h

00h

01h

02h

00h

01h

Lower byte

00h

01h

02h

03h

04h

05h

00h

01h

00h to 64h

00h to 64h

00h

01h

02h

00h

01h

00h

01h

00h

01h

00h

01h

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

00h to FFh

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

25

Item

STATUS ERROR

STATUS POWER

CONTROL MODE SEL

LAMP TIMER

ROM VERSION

SC ROM VERSION

STATUS SECURITY *3

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B High Save

W/B Low Save

Sircs (15 bit category)

Sircs (20 bit category)

26

Item

ACK

NAK

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

03h

17h

19h

(VPL-PX35, PX40, PX41)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

(VPL-PX35, PX40, PX41)

Lower byte

01h

02h

05h

13h

1Dh

1Eh

1Fh

<Table 2>

Data

NO ERROR

LAMP ERROR

FAN ERROR

COVER ERROR

TEMP ERROR

D5V ERROR

POWER ERROR

WARNING ERROR

STANBY

START UP

STARTUP LAMP

POWER ON

COOLING1

COOLING2

SAVING COOLING1

SAVING COOLING2

SAVING STABY

USER MODE

SERVICE MODE

LAMP USE TIME

MAIN ROM VERSION

SC ROM VERSION

Disable

Enable

_

Data

Upper byte Lower byte

00h 00h

00h 01h

00h

00h

00h

00h

00h

00h

00h

02h

04h

08h

10h

20h

40h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

0000h-ffffh *1

*2

05h

06h

07h

08h

00h

01h

01h

02h

03h

04h

00h

00h

00h

*2

00h

01h

00h 01h

02h

03h

04h

05h

06h

Refer to table 8

Refer to table 9

Data

Remarks

Get only

Set only

_

_

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

00h

00h

00h

00h

Set only *4

*1 Example) In case the lamp timer indicates

1000H, return values are [03h] upper byte and

[E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

Approximate Return Waiting Times

The await-return time is approx. 50 msec.

n

This is the case, unless the communications are interfered anyway.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

Volume

ColTemp

Wide Mode

Scan Conv

PictureMuting

AudioMuting

Input-A Signal Sel

Input-B Select

Lamp Mode

Gain Red

Gain Green

Gain Blue

Bias Red

Bias Green

Bias Blue

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

(VPL-CX75, CX76)

Lower byte

01h

02h

80h

81h

82h

83h

84h

85h

10h

11h

12h

13h

14h

16h

17h

20h

21h

30h

31h

32h

33h

40h

Data

Video

S-Video

Input-A

Input-B

Dynamic

Standard

Setting value (0 - 100)

Setting value (0 - 100)

Setting value (0 - 100)

Setting value (0 - 100)

High

Middle

Low

Setting value (0 - 100)

High

Low

Off

On

Off

On

Off

On

Off

On

Computer

Component

Video GBR

Memory Stick

Air Shot

High

Standard

Setting value (0 - 255)

Setting value (0 - 255)

Setting value (0 - 255)

Setting value (0 - 255)

Setting value (0 - 255)

Setting value (0 - 255)

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

01h

02h

Lower byte

00h

01h

02h

03h

00h

01h

00h - 64h

00h - 64h

00h - 64h

00h - 64h

00h - 64h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

02h

03h

04h

00h

01h

00h - FFh

00h - FFh

00h - FFh

00h - FFh

00h - FFh

00h - FFh

Remarks

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

27

(VPL-CX75, CX76)

Item

Status Error

Status Power

Control Mode Select

Lamp Timer

ROM Version

SC ROM Version

Status Security

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

Lower byte

01h

02h

05h

13h

1Dh

1Eh

1Fh

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B Low Save

W/B High Save

Sircs(15bit category)

Sircs(20bit category)

Item

ACK

NAK

03h

17h

19h

01h

02h

03h

04h

05h

06h

Refer to table 10

Refer to table 11

(VPL-CX75, CX76)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

Data

Data

No Error

Lamp Error

Fan Error

Cover Error

Temp Error

D5V Error

POWER ERROR

Warning Error

Stanby

Start Up

Start Up Lamp

Power On

Cooling1

Cooling2

Saving Cooling1

Saving Cooling2

Saving Stanby

User Mode

Service Mode

Lamp Use Time

MAIN ROM Version

SC ROM Version

Disable

Enable

_

_

_

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

28

<Table 2>

Data

Upper byte Lower byte

00h 00h

00h

00h

00h

00h

00h

00h

01h

02h

04h

08h

10h

20h

00h

00h

00h

00h

00h

40h

00h

01h

02h

03h

00h

00h

00h

00h

00h

00h

08h

00h

00h 01h

0000h-FFFFh

*1

*2

04h

05h

06h

07h

*2

00h

00h

00h

00h

01h

00h

Remarks

Get only

Set only

00h

00h

00h

00h

Set only *4

*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

The await-return time of return value is approx. 50 msec.

n

This is the case, unless the communications are interfered anyway.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

Volume

ColTemp

Wide Mode

Scan Conv

Picture Muting

Audio Muting

Input-A Signal Sel

Lamp Mode

Gain Red

Gain Green

Gain Blue

Bias Red

Bias Green

Bias Blue

00h

00h

00h

00h

00h

00h

00h

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

Lower byte

01h

02h

80h

81h

82h

83h

84h

85h

10h

11h

12h

13h

14h

16h

17h

20h

21h

30h

31h

32h

40h

(VPL-CX80)

Data

Video

S-Video

Input-A

Input-B

Dynamic

Standard

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

High

Middle

Low

Setting value (0-100)

High

Low

Off

On

Off

On

Off

On

Off

On

Computer

Component

Video GBR

High

Standard

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

01h

02h

Lower byte

00h

01h

02h

03h

00h

01h

00h-64h

00h-64h

00h-64h

00h-64h

01h

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-64h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

02h

00h

Remarks

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

29

(VPL-CX80)

Item

Status Error

Status Power

Control Mode Select

Lamp Timer

ROM Version

SC ROM Version

Status Security

Item

ACK

NAK

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

Lower byte

01h

02h

05h

13h

1Dh

1Eh

1Fh

Data

No Error

Lamp Error

Fan Error

Cover Error

Temp Error

D5V Error

Power ERROR

Warning Error

Stanby

Start Up

Startup Lamp

Power On

Cooling1

Cooling2

Saving Cooling1

Saving Cooling2

Saving Stanby

User Mode

Service Mode

Lamp Use Time

MAIN ROM Version

SC ROM Version

Disable

Enable

_

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

0000h-FFFFh

*1

*2

*2

00h

00h

00h

Lower byte

00h

01h

02h

04h

08h

10h

20h

40h

00h

01h

02h

03h

04h

05h

06h

07h

08h

00h

01h

00h

01h

00h

Remarks

Get only

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B Low Save

W/B High Save

Sircs (15 Bit Category)

Sircs (20 Bit Category)

30

03h 01h

02h

03h

04h

05h

06h

Refer to table 12

Refer to table 13

Set only

17h

19h

(VPL-CX80)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

Data

_

_

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

00h

00h

00h

00h

Set only

*4

*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

The await-return time of return value is approx. 50 msec.

m

. This is the case, unless the communications are interfered anyway.

. If standby mode is set as “low”, the main part of a projector will go into power-saving mode in about 1 minute after standby.

A command is executed by resending, although “Not

Applicable” will return, if a command is sent into powersaving mode.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

Volume

ColTemp

Wide Mode

Scan Conv

Picture Muting

Audio Muting

Input-A Signal Sel

Input-C Select

Lamp Mode

Gain Red

Gain Green

Gain Blue

Bias Red

Bias Green

Bias Blue

00h

00h

00h

00h

00h

00h

00h

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

(VPL-CX85, CX86)

Lower byte

01h

02h

80h

81h

82h

83h

84h

85h

10h

11h

12h

13h

14h

16h

17h

20h

21h

30h

31h

32h

33h

40h

Data

Video

S-Video

Input-A

Input-B

Input-C

Dynamic

Standard

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

High

Middle

Low

Setting value (0-100)

High

Low

Off

On

Off

On

Off

On

Off

On

Computer

Component

Video GBR

Memory Stick

Air Shot

High

Standard

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

01h

02h

Lower byte

00h

01h

02h

03h

04h

00h

01h

00h-64h

00h-64h

00h-64h

00h-64h

00h-64h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

02h

03h

04h

00h

01h

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

Remarks

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

31

(VPL-CX85, CX86)

Item

Status Error

Status Power

Control Mode Select

Lamp Timer

ROM Version

SC ROM Version

Status Security *3

Item

ACK

NAK

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

Lower byte

01h

02h

05h

13h

1dh

1eh

1fh

Data

No Error

Lamp Error

Fan Error

Cover Error

Temp Error

D5V Error

Power Error

Warning Error

Stanby

Start Up

Startup Lamp

Power On

Cooling1

Cooling2

Saving Cooling1

Saving Cooling2

Saving Stanby

User Mode

Service Mode

Lamp Use Time

MAIN ROM Version

SC ROM Version

Disable

Enable

_

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

0000h-FFFFh

*1

*2

*2

00h

00h

00h

Lower byte

00h

01h

02h

04h

08h

10h

20h

40h

00h

01h

02h

03h

04h

05h

06h

07h

08h

00h

01h

00h

01h

00h

Remarks

Get only

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B High Save

W/B Low Save

Sircs (15 Bit Category)

Sircs (20 Bit Category)

32

03h 01h

02h

03h

04h

05h

06h

Refer to table 14

Refer to table 15

Set only

17h

19h

(VPL-CX85, CX86)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

Data

_

_

Lower byte

00h

01h

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

00h

00h

00h

00h

Set only

*4

*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

The await-return time of return value is approx. 50 msec.

m

. This is the case, unless the communications are interfered anyway.

. If standby mode is set as “low”, the main part of a projector will go into power-saving mode in about 1 minute after standby.

A command is executed by resending, although “Not

Applicable” will return, if a command is sent into powersaving mode.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

Item

Input

Picture Mode

Contrast

Brightness

Color

Hue

Sharpness

Volume

ColTemp

Wide Mode

Scan Conv

Picture Muting

Audio Muting

Input-A Signal Sel

Input-C Select

Lamp Mode

Gain Red

Gain Green

Gain Blue

Bias Red

Bias Green

Bias Blue

00h

00h

00h

00h

00h

00h

00h

<Table 1>

Item Number

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

(VPL-CX61, CX63)

Lower byte

01h

02h

80h

81h

82h

83h

84h

85h

10h

11h

12h

13h

14h

16h

17h

20h

21h

30h

31h

32h

33h

40h

Data

Video

S-Video

Input-A

Input-B

Dynamic

Standard

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

Setting value (0-100)

High

Middle

Low

Setting value (0-100)

High

Low

Off

On

Off

On

Off

On

Off

On

Computer

Component

Video GBR

Memory Stick

Air Shot

High

Standard

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

Setting value (0-255)

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

01h

02h

Lower byte

00h

01h

02h

03h

00h

01h

00h-64h

00h-64h

00h-64h

00h-64h

04h

00h

01h

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-FFh

00h-64h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

00h

01h

02h

03h

Remarks

Set/Get

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

33

(VPL-CX61, CX63)

Item

Status Error

Status Power

Control Mode Select

Lamp Timer

ROM Version

SC ROM Version

Status Security *3

Item

ACK

NAK

<Table 1>

Item Number

Upper byte

01h

01h

01h

01h

01h

01h

01h

Lower byte

01h

02h

05h

13h

1Dh

1Eh

1Fh

Data

No Error

Lamp Error

Fan Error

Cover Error

Temp Error

D5V Error

Power Error

Warning Error

Stanby

Start Up

Startup Lamp

Power On

Cooling1

Cooling2

Saving Cooling1

Saving Cooling2

Saving Stanby

User Mode

Service Mode

Lamp Use Time

MAIN ROM Version

SC ROM Version

Disable

Enable

_

<Table 2>

Data

Upper byte

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

0000h-FFFFh

*1

*2

*2

00h

00h

00h

Lower byte

00h

01h

02h

04h

08h

10h

20h

40h

00h

01h

02h

03h

04h

05h

06h

07h

08h

00h

01h

00h

01h

00h

Remarks

Get only

Channel Memory Reset

Status Memory Reset

Set Memory Reset

W/B All Save

W/B Low Save

W/B High Save

Sircs (15 Bit Category)

Sircs (20 Bit Category)

34

03h 01h

02h

03h

04h

05h

06h

Refer to table 16

Refer to table 17

Set only

17h

19h

(VPL-CX61, CX63)

<Table 3>

Item Number

Data

_

Undefined Command

Size Error

Select Error

Range Over

Not Applicable

Check Sum Error

Framing Error

Parity Error

Over Rub Error

Other Comm Error

Upper byte

00h

01h

F0h

Data

_

_

00h

00h

00h

00h

Set only

*4

Lower byte

00h

01h

*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.

*2 Example) In case the software version is 1.03, return values are [01h] upper byte and [03h] lower byte.

*3 While the set is security locked, after power switch is turned on, you can check that pass sword input screen is indicated or not.

During pass word input screen indicating, return values are [00h] upper byte and [01h] lower byte.

*4 It is corresponded to single command only.

04h

05h

06h

0Ah

10h

20h

30h

40h

50h

The await-return time of return value is approx. 50 msec.

m

. This is the case, unless the communications are interfered anyway.

. If standby mode is set as “low”, the main part of a projector will go into power-saving mode in about 1 minute after standby.

A command is executed by resending, although “Not

Applicable” will return, if a command is sent into powersaving mode.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

35

36

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

37

38

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

39

40

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

41

42

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

43

44

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

45

46

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

47

48

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

The material contained in this manual consists of information that is the property of Sony Corporation.

Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.

Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation.

Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des opérations ou entretiens de l’équipement à moins d’une permission écrite de Sony

Corporation.

Das in dieser Anleitung enthaltene Material besteht aus

Informationen, die Eigentum der Sony Corporation sind.

Die Sony Corporation untersagt ausdrücklich die

Vervielfältigung jeglicher Teile dieser Anleitung oder den

Gebrauch derselben für irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrüstung ohne ausdrückliche schriftliche Erlaubnis der Sony Corporation.

VPL-CX61/CX63/CX75/CX76/CX80/CX85/CX86/FX51/FX52/FX52L/PX35/PX40/PX41

VPL-CX61 (SY)

VPL-CX63 (SY)

VPL-CX75 (SY)

VPL-CX76 (SY)

VPL-CX80 (SY)

VPL-CX85 (SY)

VPL-CX86 (SY)

VPL-FX51 (SY)

VPL-FX52 (SY)

VPL-FX52L (SY)

VPL-PX35 (SY)

VPL-PX40 (SY)

VPL-PX41 (SY) E

9-968-277-01

Sony Corporation

Printed in Japan

2006. 5 16

©2002

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement