Installation Instructions

Installation Instructions
Installation
Instructions
27” Built In Wall Oven
JKP15, JKP18, JKP27BA, JKP27, JKP45, JKP56 JKS05,
JK910AA, JK910, JK950
“If you have questions, call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
Before you begin
• Note to Installer- Be sure to leave these
instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• NOTE- This appliance must be properly
grounded.
Read these instructions carefully and completely
• IMPORTANT-Save these instructions for
local inspector’s use.
• IMPORTANT-Observe all governing
codes and ordinances.
Parts Included
4 screws (single)
8 screws (double)
Materials Needed
Wire Nuts
Bottom Trim
Strain Relief
Clamp
Junction
Box
36” of String
Tools You Will Need
1/8” Drill Bit &
Electric or
Hand Drill
Pub. No. 31-10461
229C4053P429
Phillips
Screwdriver
1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Electrical
Requirements
For Your Safety
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located on oven frame.)
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are no
local codes, your range must be wired and
fused to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a 4 conductor
connection to an electric range. When
installing an electric range in new construction,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings around the oven can withstand the
temperatures (up to 200°F.) generated by
the oven.
CAUTION: The electrical power
to the oven supply line must be
shut off while line connections
are being made. Failure to do so
could result in serious injury or
death.
2
Installation Instructions
Pre- Installation Checklist
Open the door to the stop position.
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES ARE
TO BE USED FOR SINGLE AND
DOUBLE OVEN INSTALLATION!
Remove packaging materials.
Check behind hinges, and under
false bottom. Remove labels on
door, plastic on trims and panel,
and all tape around oven.
DO NOT LIFT THE DOOR BY THE
HANDLE!
Grasp the door on both sides and
lift up and off the hinges.
Oven Racks
EAS
Y INST
ALL
EASY INSTALLATION
OFNYOUR NEW
30" ATIO
OF
WAL
30" WALL
OVEN
L OVE YOUR
NEW
N
Broiler Pan
and Grid
Before
IMPORTyou begin-R
IMPORT ANTead
ANT- Save thesethese instruct
Note
to InstalleOBSER
instruct
OWNER
ions
Before
you begin-Read
these instructions
completely
and carefully.
comple
ions
r- Be VE ALL
- Keep
Notefor local
IMPORTANTSave these
instructions
for local
inspector's
GOVER
sure
telyuse.
these
This
to leave
and
NING
inspect
applian
IMPORTANT- OBSERVE
ALL
GOVERNING
CODES AND
ORDIANCES.
instruct
carefull
CODES
these
or's
ce must
y.
Note to Installer- Be sure
to leaveions
these instructions
the consumer.
instruct with
use.
AND
for future
be
ORDIAN
ions
OWNER- Keep these instructionsproperl
for future
reference.
referen with
FOR
CES.
y ground
the
YOUR
Note- This
appliance must be properly grounded
(if applicable).
ce.
consum
ed (if
SAFETY
Before
er.
applica
instruct you begin-R
ble).
carefull ions comple ead
these
FOR
ELECTRICAL REQUIREMENTS
y. YOUR SAFETY
IMPORT
tely
and
ELECTR
instruct ANTBefore
begin-Read these
ionsyouSave
Before youICAL
begin-Read
IMPORT
these
REQUIRthese
for local
Before
instructions
completely and
ANTinstructions completely EMENT
and
GOVER
inspect
instruct you begin-R
NING OBSER
S
carefully.
Note carefully.
or's
VE
carefull ions comple ead
to InstalleCODES
use.
Save ALL
these
these IMPORTANTIMPORTANT- Save these
these
IMPORT y.
r- BeforAND
instruct
tely
instructions
local inspector's use.
OWNER
instructions for local
inspector's use.
and
sure ORDIAN
instruct ANTto leave
OBSERVE
ALLCES.
- Keep ions with
Save OBSERVE ALL
for futureIMPORTANTIMPORTANTthe AND ORDIANCES. IMPORT ions for
these
these CODES
GOVERNING
Notereferen
localCODES AND ORDIANCES.
instructconsum
ANTGOVER GOVERNING
inspect
ce.
to InstallerBe ions
sure toer.
leave
properlThisNote
applian
Note
to
Installer- Be sure
to leave
NING OBSER
Note
Before y ground
VE ALL or's use.
these instructions
ce must with the consumer.
to theseCODES
instructions
with the consumer.
these Installe
instruct youOWNERed (if
AND
be instructions
begin-R
Keep
these
r- Be
instruct
OWNERKeep these
instructions
applica
OWNER
sure ORDIAN
carefull ionsfor
ions reference.
futureead
reference.
comple
to leave CES.
these ble).
for future
for future- Keep
with
IMPORT y. Note- This
telyappliance must be
the
and
Note-these
This instruct
appliance
must be
consum
Notereferen
instruct ANTproperly
grounded (if applicable). properlThis properly
Save
er.
ce. groundedions
(if applicable).
applian
IMPORT ions for
these
Before
you begin-Read these
Before you begin-Read these
Before
y
local
ground ce must
GOVER ANT- instructions
completely and
inspect
instructions
completely
and
instruct you begin-R
ed (if
be
NING OBSER
Note
applica
carefully.
VE ALL or's use.
carefully.
carefull ions comple
CODES
ead
to
theseble).
these Installe IMPORTANTSave these
IMPORT y.
IMPORTANTSave these
tely
instruct r- Be AND ORDIAN
OWNER
and
sure
for local inspector'sinstruct
use.
ANT- instructions
ionsinstructions
for local inspector's use.
to leave CES.
Save
for future- Keep
with
IMPORTANTOBSERVE ALL IMPORT ions
these
the
IMPORTANTOBSERVE ALL
these
for local
Notereferen GOVERNING
instructconsum
CODES AND ORDIANCES.
GOVER ANTGOVERNING
CODES
AND
ORDIANCES.
This
inspect
er.
properl
ions
appliance.
NING OBSER
Note
or's Be sure to leave
NoteVE
to Installery ground ceNote to Installer- Be sure to leave
CODES
to
use.
ALL
must
these Installe
with the consumer.
these instructions with the consumer.
ed (ifthese instructions
be
instruct r- Be AND ORDIAN
applica Keep these instructions
OWNER
OWNERsure
Keep these instructions
ions OWNERble).
to leave CES.
for future- Keep
with
for future reference.
reference.
the
these for future
consum
Notereferen
Note- This appliance must be
instruct
NoteThis appliance must be
er.
properlThis appliance.
ions
properly grounded (if applicable).
properly
grounded
(if
applicable).
y ground ce
must
ed (if
be
applica
Literature
Pack
ble).
Open oven door and remove literature
pack, broiler pan and grid, and oven
racks.
Remove Installation Instruction from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place
for future reference.
NOTE:The oven door is very heavy. Be
sure you have a firm grip before lifting the
oven door off the hinges. Use caution
once the door is removed. Do not lay the
door on its handle. This could cause
dents or scratches
EASY INSTALLATION OF YOU NEW
30" WALL OVEN
Before you begin-Read these instructions completely and carefully.
IMPORTANT- Save these instructions for local inspector's use.
IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave these instructions with the consumer.
OWNER- Keep these instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
FOR YOUR SAFETY
ELECTRICAL REQUIREMENTS
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
Before you begin-Read these
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODES AND ORDIANCES.
Note to Installer- Be sure to leave
these instructions with the consumer.
OWNER- Keep these instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
3
(Continued on following page)
Installation Instructions
Pre- Installation Checklist
cont.
Place the oven on a table or platform
even with the cutout opening.
(Platform must support 150 lbs.
single, 275 lbs. double.)
Cover hinge with paper towel rolls
or toweling.
Remove the bottom trim from the
top of the oven. It will be installed at
the end of installation. The trim is
wrapped separately and taped to the
top of the unit.
CAUTION: When the door is
removed and the hinge arms
are at the stop postion, DO
NOT bump or try to move the
hinge arms. The hinges could
snap back causing an injury to
the hands. Cover the hinges with
toweling or empty towel rolls
while working in the oven area.
Bottom
Trim
Conduit
Side
Trim
4
Installation Instructions
A1
Cutouts for Single Built-In-Oven
Cabinet
Width
27"
10"
Junction Box
Location
Cutout
Width
25" MIN.
25 1/4" MAX.
Allow 7/8"
for overlap of
oven over side
edges of cutout
32 1/2”
Cutout Depth
23 1/2”
Cutout Width
25” Min.
25 1/4” Max.
5"
Cutout Height
27 5/8” Min.
28 1/8” Max.
20"
Alternate
junction box
location
Recommended
cutout location
from floor
32 1/2"
Allow a minimum of 20"
for clearance to adjacent
corners, drawers, walls, etc.
when door is open
27
34"
To bottom of
junction box
Cutout
Height
27 5/8" MIN.
28 1/8" MAX.
2" x 4" or
equivalent
runners
Cabinet Width
Recommended
Cutout Location
from Floor
Allow 1" for
overlap of oven
top and bottom
of cutout
NOTE: If the cabinet does not
have a front frame and the
sides are less than 3/4” thick,
shim both sides equally to
establish the cutout width.
If the cabinets do not have a solid
bottom, then two braces or runners
must be installed to support the
weight of the oven. For single
ovens the runners and braces must
support 150 pounds.
2" x 4" or
Equivalent
Runners
24"
19"
27"
This Oven is not approved for stackable
or side by side installation
5
Installation Instructions
A2
Cutouts for Double Built-In-Oven
Junction Box
Location
Cabinet
Width
27"
10"
Cutout
Width
25" MIN.
25 1/4" MAX.
Allow 7/8"
for overlap of
oven over side
edges of cutout
2" x 4" or
equivalent
runners
56"
To bottom of
junction box
Alternate
junction
box
location
Cutout
Height
49 11/16" MIN.
50 1/8" MAX.
5"
20"
Allow a minimum of 20"
for clearance to adjacent
corners, drawers, walls, etc.
when door is open
Allow 1" for
overtlap of oven
top and bottom
of cutout
Cabinet Width
Recommended
Cutout Location
from Floor
27”
13 1/4”
Cutout Depth
23 5/8” Min.
Cutout Wdth
25” Min.
25 1/4” Max.
Cutout Height
49 11/16” Min.
50 1/8” Max.
Recommended
cutout location
from floor
13 1/4"
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4” thick, shim
both sides equally to establish
the cutout width.
CL
SUITABLE
BRACING
TO SUPPORT
RUNNERS
21 5/8"
OVER CENTERLINE
OF CABINET
2" x 4" or
EQUIVALENT
RUNNERS
If the cabinet does not have a solid bottom,
then two braces and runners must be
installed to support the weight of the oven.
For double ovens the runners and braces
must support 275 pounds.
6
Installation Instructions
A3
Cutouts for Single Oven
Under Counter
Gas or electric cooktops
may be installed over this
oven. See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
Gas or electric connections
for gas cooktop must be
located in an adjacent
accessible location
to the right
240V / 208V
Junction Box
Location
25"
5"
25" MIN.
25 1/4" MAX.
27 5/8" MIN.
28 1/8" MAX.
Allow 1"
unit overlap
all edges
22" MIN.
Above
Support
Platform
32"
Typical
Countertop
Height
24"
3/4" Support
Platform
Required
MUST SUPPORT 150 LBS.
NOTE: This Oven is not approved to be
installed under a Solid Disk, Induction or
Downdraft Modular Cooktop.
7
Installation Instructions
B
B1
B2
Electrical Connections
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
NEW CONSTRUCTION AND FOURCONDUCTOR BRANCH CIRCUIT
CONNECTION
With the oven in front of the cabinet
opening, on a table or platform, connect
the flexible conduit to the electrical
junction box as shown below. You will
need to purchase a strain relief clamp
to complete the connection of the
conduit to the junction box.
JUNCTION BOX
LOCATION
B3
• When installing in a new
construction, or
• When installing oven in a mobile
home, or
• When local codes do not permit
grounding through neutral:
a. Cut the neutral (White) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
5"
Ground
Wires
Ground
Wires
CONDUIT
48 1/2"
LONG
BARE
GROUND
RED
Junction
Box Cover
WHITE
BLACK
PLACE OVEN ON
A SUPPORT
TO ASSIST IN
CONNECTING
CONDUIT
STRAIN RELIEF CLAMP
( NOT INCLUDED )
MUST BE USED
AT JUNCTION BOX
b.Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING note.
c.Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray) in
accordance with local codes, using wire
nut.
d.Connect the oven red lead to the branch circuit
red lead and the oven black lead to the branch
circuit black lead in accordance with local
codes, using wire nuts. If the residence red,
black or white leads are aluminum conductors,
see “ WARNING” note on following page.
e. Install Junction Box Cover.
8
( Continued on Next Page)
Installation Instructions
B Electrial Connections
cont.
OR
Do not shorten the flexible conduit.The
conduit strain Relief Clamp must be
securely attached to the junction box
and the flexible conduit must be
securely attached to the clamp. If the
flexible conduit will not fit within the
clamp, do not install the oven until a
clamp of the proper size is obtained.
Three-Conductor Branch
B4 Circuit Connection
When connecting to a 3-conductor branch
circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to the
branch circuit neutral (white or gray in
color), using wire nut.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are UL
recognized for connection to larger gauge
household wiring. The insulation of these 3
leads is rated at temperatures much higher
than the temperature rating of household
wiring. The current carrying capacity of the
conductor is governed by the temperature
rating of the insulation around the wire,
rather than the wire gauge alone.
Ground
Wires
Ground and
neutral wires
Junction
Box Cover
WARNING: Improper
connection of aluminum
house wiring to copper leads
can result in an electrical hazard or
fire. Use only connectors designed
for joining copper to aluminum and
follow the manufacturer’s
recommended procedure closely.
b.Connect the oven red lead to the branch
circuit red lead, using wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using wire nut.
d.Install Junction Box Cover.
9
Installation Instructions
C Placing the Oven in the Opening
C1 Sliding the Oven Into the
C3 Drilling the Pilot Holes
Opening.
a. Loop a 36” string around the conduit before
the oven is slid into place. This will keep the
conduit from falling behind the oven.
Note: Before drilling the pilot holes
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill four-1/8” pilot holes through the
mounting holes (top and bottom) of the side
trim, for the four #8 screws provided. Drill
eight holes for the Double Oven.
Pull out on string
loop while
pushing the oven
into the cabinet
b. Lift oven into cabinet cutout using the oven
opening as an grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the oven
in a natural loop.
d. When you are sure the conduit is out of the
way, slide the oven all the way back into the
opening. Remove the string.
MOUNTING
HOLE
LOCATIONS
NOTE: Mounting screws must be
used. Failure to do so could result in
the oven falling out of the cabinet
causing serious injury.
C2 Installing the Bottom Trim
a. Slide the oven 3/4 way into the cabinet
cutout.
b. Attach the bottom
trim to the front frame
with the 3 screws
provided.
c. Slide the oven all
the way into the
cabinet cutout.
Lower
Trim
The screws must be
a minimum of 1/4”
from the front of the
cutout.
b. Secure the oven to cabinet with screws
provided.
Side
Trim
NOTE: If the cabinet is particle board, you
must use 4 #8 x 3/4 particle board screws.
These may be purchased at any hardware
store.
Trim
Screw
CAUTION: Be sure you do not tip the
oven foward during installation or
you may bend the Bottom Trim. The
Bottom Trim provides an opening for
cooling air to enter the cabinet. This
opening should never be blocked.
10
Installation Instructions
D Replacing the Oven Door
D1
Make sure the hinge is in the door
stop position.
D2
Remove the toweling or paper towel
holder from the hinge.
D3
Grasp the door on both sides.
D4
Hold the door over the hinges lining up
the hinges with the hinge slots on the
bottom of the door.
D5
Slide the door down onto the hinges as
far as it will go.
D6
Close the door.
The oven door is heavy. You may need
help lifting the door high enough to
slide it down onto the hinges. Do not
lift the door by the handle.
11
Installation Instructions
E PRE-TEST CHECK LIST
Remove all protective film if present,
and any stickers.
Check that the bottom trim is installed
properly (see page 7).
Check to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check to be sure the mounting screws
are installed and flush with the side
trim, (see page 7).
Operation Checklist
NOTE TO ELECTRICIAN:
The power leads supplied with this
appliance are UL recognized for
connections to larger gauge
household wiring. The insulation of
these leads is rated at temperatures
much higher than the temperature
rating of household wiring. The
current carrying capacity of a
conductor is governed by the wire
gauge and also the temperature rating
of the insulation around the wire.
Remove all items from the inside
of the oven.
Turn on the power to the oven.
(Refer to your Use and Care
Manual.) Verify that the bake and
broil units, and all cooking
functionsoperate properly.
Check that the circuit breaker is
not tripped or the house fuse is
blown.
NOTE: ALUMINUM WIRING
A. WARNING:
IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO
THE COPPER LEADS CAN
RESULT IN A SERIOUS PROBLEM.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum and
follow the manufacturer’s
recommended connector
procedure closely.
NOTE:Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice and
local codes.
Check that conduit is securely
connected to the junction box.
See Use & Care manual for
troubleshooting list.
12
Pub. No. 31-10461
229C4053P429
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement