Owner`s Manual
Owner's Manual
PP052208
TablE of Contents
SAFETY INSTRUCTIONS
1
PRODUCT BENEFITS
3
MAIN PARTS
4
OPERATING THE PurePro® PROFESSIONAL Thank you for purchasing the PurePro®
professional air purifier and congratulations
on taking this important step in improving
the quality of air in your home, office or
other environments. Customer satisfaction
is our number one goal. Your PurePro®
professional air purifier is a premium air
purifying appliance which comes with a
limited one-year warranty.
AIR PURIFIER
5
Getting Ready
5
Controls/Settings
5
Enjoy your PurePro ® professional air
purifier and visit our website for more
exciting quality products and upgrades at
www.thepurepro.com.
Preparing to Clean
Cleaning the ESP cell & Pre Filter
9
Cleaning the Oxygen Plus™ Filter
11
Cleaning External Surfaces
11
OPERATION
6
Selecting a Setting
6
The Ions Button
7
Clean Light
7
CLEANING & MAINTENANCE
7
8
ELECTROSTATIC FILTER (ESP CELL) INSERTION
12
MORE THINGS YOU SHOULD KNOW
12
Ozone and Your Health
12
ORDERING an EXTRA ESP cell, PRE-filter set &
wall mount bracket
13
TROUBLE-SHOOTING
14
ONE-YEAR LIMITED WARRANTY
15
ARBITRATION AGREEMENT
16
1
SAFETY INSTRUCTIONS
EXTREMELY IMPORTANT INFORMATION: Safety
precautions should always be used when operating
this or any electrical appliance. Decrease the risk of
electrocution, electric shock, injury or fire by reading
and following all the warnings below:
Use only as described in this PurePro® professional air
purifier Owner’s Manual. To reduce the risk of electric
shock, do not attempt to service the product in any way
other than in the manner described in the “CLEANING
& MAINTENANCE” section of this manual.
Do not use the PurePro® professional air purifier
outdoors.
Do not use the PurePro® professional air purifier in
bathrooms or other humid environments, near fireplaces
or in areas where flammable or combustible vapors or
products may exist.
The PurePro® professional air purifier operates at 120v
AC and 60Hz only.
To reduce the risk of electric shock, this product has a
grounding-type plug that has a third grounding pin. This
plug will fit only into a grounding-type power outlet. If
the plug does not fit into the outlet, contact qualified
service personnel to install the proper outlet. Do not
alter the plug in any way.
Always turn off all controls before unplugging the
PurePro® professional air purifier from outlet.
Always turn off and unplug this product from outlet
before cleaning the electrostatic filter ESP cell, prefilter and Oxygen Plus™ filter.
2
Never touch the internal parts, such as electrodes,
ionizing wires, or any internal part within the PurePro®
professional air purifier with your hand or with
any object.
Do not open the outer casing of the PurePro®
professional air purifier. Attempting to open the unit
will cause the warranty to be voided and could cause
serious personal injury to the user and/or result in
considerable damage to the unit.
Do not place the PurePro® professional air purifier cord
near a heated surface.
Never operate the PurePro® professional air purifier
if the plug or cord is damaged or appears damaged.
Only qualified service personnel should ever replace or
attempt to replace a damaged power cord.
Never use the power cord to pick up, carry, drag, pull,
or lift the PurePro® professional air purifier. Do not pull
the cord against or around sharp corners and edges.
This could result in injury to the user and damage to
the cord.
Always remove the plug from its power outlet by holding
onto the plug itself and pulling gently. Never pull on the
cord itself to unplug it from its power outlet.
Use care when operating the PurePro® professional air
purifier by keeping all fingers, body parts, hair, loose
clothing and jewelry away from openings.
Never touch the PurePro® professional air purifier or its
plug with wet hands.
The PurePro® professional air purifier is an electrical
appliance. The PurePro® professional air purifier should
be operated by adults only.
3
4
Main parts
Do not touch the ESP cell until after discharging residual
electricity by touching blades to an electrical ground such
as a water pipe or metal faucet.
Before using your PurePro® professional air purifier,
please read all the information contained in this manual.
The ESP cell should be inspected frequently and cleaned
regularly to prevent excessive accumulation that may result
in an electrical flashover or risk of fire.
ALWAYS RE-INSERT The ESP cell, Pre-Filter AND
OXYGEN PLUS™ Filter IN A VERTICAL MANNER. SEE
THE “ELECTROSTATIC FILTER (ESP CELL) INSERTION”
SECTION OF THE MANUAL FOR MORE INFORMATION.
A
G
C
F
B
H
D
E
PRODUCT BENEFITS
Your PurePro® professional air purifier boasts:
• 5 stage purification
• Whisper quiet operation
• Most effective air purifier in its class*
• ENERGY STAR® certification
• Compact tabletop design
•ESP cell that never needs replacing
•Cleans the air in a 30 x 30 room in a little over
an hour**
•CADR 178 (pollen)
* Based on CADR ratings of products in the counter top
electrostatic air cleaner category on the market as of 10/12/06.
** The PurePro® air purifier generates enough contaminant free air
to completely fill a 30’X 30’ X 8’ room in 71 minutes based on CADR
measurements as defined by ANSI standard.
A. ESP cell
This is the ESP cell. It’s a vital part of this amazing air
purifying system. This is where smoke, dust, allergens,
germs, and irritants are trapped when the PurePro®
professional air purifier is in use.
B. PRE-FILTER
This filter traps large particles such as hair and lint.
C. OXYGEN PLUS™ FILTER
The Oxygen Plus™ filter converts ozone molecules
into oxygen molecules thereby decreasing the
concentration of the ozone that is emitted by the
air purifier.
D.RELEASE BUTTON
E.AIR INLET GRILL
F. COVER
G.AIR OUTLET GRILL
H.CLEANING BRUSH
5
OPERATING THE PurePro®
PROFESSIONAL AIR PURIFIER
Getting Ready
Locate a level surface on which to place your PurePro®
professional air purifier and a grounded 120v outlet.
Position your PurePro® professional air purifier at least
one foot from the wall. Follow warnings described in the
“SAFETY INSTRUCTIONS” section of this manual.
Plug in the unit. You are now ready to turn on your
PurePro® professional air purifier!
Controls/Settings
Silent
Everyday
Use
Rapid
Clean
Off
Boost
Clean
6
4. BOOST Recommended for large rooms and areas exposed to heavy dust. At this setting, the unit will run at high speed.
5. CLEAN This red light goes on when your PurePro® professional air purifier needs to be cleaned, or the unit is experiencing some other problem. See the “CLEANING &
MAINTENANCE” and the
“TROUBLE-SHOOTING”
sections of this manual for
more information.
6. IONS Emits negative ions to freshen the stale air, returning clean, pure air into the room.
OPERATION
IONs
1. CONTROL KNOBTurns the unit on and off.
Selecting a Setting
2. SILENCE EVERYDAY
USE
Recommended for bedrooms or other quiet places. At this
setting the unit will run at low
speed with whisper-quiet
operation.
Set up your PurePro® professional air purifier as
described in the “Getting Ready” section of this
manual. Turn the control knob to activate your
PurePro® professional air purifier and get ready to
enjoy clean, ionized air according to the setting you
select.
3. RAPID CLEAN
Recommended for average-
sized rooms where windows and doors are rarely opened. At this setting, the unit will run at medium speed.
There are four settings controlled by the control
knob. The different settings are OFF position,
SILENT EVERYDAY USE mode, RAPID CLEAN
mode, BOOST mode. Turn the control knob to rotate
through the settings. The LED indicators will light up
7
to indicate your current setting (SILENT EVERYDAY
USE, RAPID CLEAN, BOOST).
The IONS button
Press the ionS button to start the ionizer while the unit
is on. The unit will release the proper concentration of
ions to keep the air fresh. Pressing the ionS button
again will turn off this feature.
Clean Light
If the unit has not been regularly cleaned and an
excessive amount of dirt has collected on the ESP
cell, the unit will shut down and the red light will turn
on. Simply clean the ESP cell and reinsert, to start
the unit.
CLEANING & MAINTENANCE
The PurePro® professional air purifier is designed
to run quietly and requires very little time and effort
to maintain in proper working condition. If you hear
excessive noise or static coming from your PurePro®
professional air purifier, it generally indicates that the
product needs to be cleaned. Turn off your PurePro®
professional air purifier, unplug the cord and carefully
follow the cleaning instructions in the “CLEANING &
MAINTENANCE” section of this manual.
Keep your PurePro® professional air purifier functioning
properly by cleaning the electrostatic filter (ESP
cell) and pre-filter after every 3-4 weeks of use as
recommended. More frequent cleaning will be
necessary if the unit is located in an area with a
high level of airborne contaminants (excessive
amounts of smoke, pet dander, etc.). The Oxygen
Plus™ filter needs to be cleaned after about 6 month
of use. See the “Cleaning the Oxygen Plus™ Filter”
section for more information.
8
More frequent cleaning is often required if your PurePro®
professional air purifier is new or if you place it in a new location.
Exposing your PurePro® professional air purifier to candle,
oil lamp, fireplace soot, and smoke is not recommended
and will require the collection blade assembly, pre-filter and
Oxygen Plus™ filter to be cleaned more frequently.
HELPFUL TIPS: If your unit doesn’t work and the CLEAN
light is on, it’s time to clean the filters.
Preparing to Clean:
1. Turn off and unplug your PurePro® professional air purifier and let it rest for 60 seconds.
2. Press the release button to open the cover.
3. Reposition the locking lever. Diagram 1
4. Remove the ESP cell by taking hold of the handles
and lifting upwards. Diagram 2
5. Remove the Oxygen Plus™ filter from the unit.
Diagram 1
Locking Lever
Diagram 2
9
Cleaning the ESP cell and Pre-Filter:
10
5. Always make sure your air purifier is turned off and
unplugged before attempting to vertically re-insert
the collection blade assembly and pre-filter.
Pre-Filter SPECIAL NOTICE:
The pre-filter is attached at the front ESP CELL attached
to the front grill. Dishwasher
1. Put the ESP cell into the dishwasher— making sure
not to damage or bend the blades or the wire.
2. After completely cleaning, remove from the
dishwasher.
3. VERY IMPORTANT: Wait until the ESP cell is
thoroughly dry before vertically re-inserting it into
your PurePro® professional air purifier and resuming
use.
4. Always make sure your air purifier is turned off and
unplugged before attempting to vertically re-insert
the ESP cell and pre-filter.
Handwash
1. Place the ESP cell into warm, soapy water and let
stand for approximately 10 minutes.
2. Use the supplied brush (a.) to clean the blades.
Make sure not to damage or bend the blades or the
wire.
3. Remove from water and rinse
(b.) with warm water. Repeat as
necessary. Make sure not to damage
or bend the blades or the wire.
4. VERY IMPORTANT: Wait until the
ESP cell is thoroughly dry before
vertically re-inserting it into your
PurePro® professional air purifier and
resuming use.
1. When in use, the pre-filter removes larger particles
from the air circulating through your PurePro®
professional air purifier.
2. It can either be hand-washed in cold water or
vacuumed following the same procedure described
in the “Cleaning the Oxygen Plus™ Filter” section
of this manual.
3. However you wash it, make sure it is absolutely dry
before attempting to vertically re-insert it into your
purifier and resuming use.
4. Always make sure your air purifier is turned off and
unplugged before attempting to vertically re-insert
the ESP cell and pre-filter.
11
12
IMPORTANT DRYING WARNING:
To avoid damaging your air purifier, make sure the ESP cell
is completely dry and free of all moisture before attempting
to vertically re-insert them into your purifier and resuming
use. See “ELECTROSTATIC FILTER (ESP CELL)
insertion” for more information.
2. Use a moist washcloth with a little dishwashing
soap to wipe the outer case surfaces.
3. Do not allow water to slip into the internal parts of
the air purifier as this could damage its functioning
and may result in injury to you.
4. Allow the unit to dry thoroughly before resuming use.
Note: If you insert a wet part, the fan will not turn on
and the CLEAN light will go on. Simply take out the part
and let it dry.
ELECTROSTATIC FILTER (ESP CELL)
INSERTION
Always make sure your air purifier is turned off and
unplugged before attempting to vertically re-insert the
ESP cell and pre-filter.
cleaning the Oxygen Plus™ Filter
IMPORTANT NOTICE: You must always clean the
Oxygen Plus™ filter with a vacuum cleaner. NEVER
use water or any other liquid to clean it. Using water
or any other liquid to clean the Oxygen Plus™ filter will
deactivate the filter. This could possibly increase the
ozone level in your room.
1. Place the Oxygen Plus™ filter on a flat surface.
2. Use a vacuum cleaner hose attachment to clean
both sides of the Oxygen Plus™ filter, making sure
that all dust is absorbed into the vacuum cleaner.
CLEANING EXTERNAL SURFACES
Over time, some particles and dust may accumulate
on the external surfaces of your PurePro® professional
air purifier.
To Clean External Surfaces:
1. Turn off and unplug the unit.
Please note that the ESP cell can not be re-inserted
when the unit is not in its vertical (upright) position. See
Diagram 2.
1. Always keep your PurePro® professional air purifier
vertically upright on a solid surface any time you
need to re-insert any of the thoroughly cleaned and
dried filters (ESP cell, pre-filter, and Oxygen Plus™
filter).
Diagram 2
2. First, insert the Oxygen Plus™ filter into the unit
along the grooves. See Diagram 1.
3. Next, insert the ESP cell into the unit in the reverse
manner in which it was removed previously.
4. Re-position the ESP cell locking lever, close the
cover, plug in and resume use.
MORE THINGS YOU SHOULD KNOW
Ozone and Your Health
After you activate your PurePro® professional air purifier,
you may notice a new clean scent. Ozone is the scent
13
you smell. Ozone is a combination of three oxygen
atoms. The PurePro® professional air purifier utilizes
an ionizing process which results in very low ozone
emission.
The PurePro® professional air purifier complies with
U.S. safety requirements for low ozone emission (less
than 50 parts per billion) and meets the UL867 standard
for consumer products. UL867 is the U.L. standard for
safety for electrostatic air cleaners.
Individuals with a history of respiratory disease, asthma,
heart disease, lung disease, breathing problems or
concerns about ozone should ask their doctor whether
the concentrations of ozone generated by this or other
commercial ionic air purifiers are appropriate for their
specific health needs.
14
trouble-shooting
Reason
Indication/
setting light
not on
Machine is unplugged.
Check if plug is loose.
Unit has not been
turned on.
Rotate control knob.
Control knob has
not been turned.
Red CLEAN
light is on
Too much dust has
accumulated.
Fan off
Electrostatic filter
(ESP cell) is wet.
Excessive
noise
ORDERING an EXTRA ESP cell, PreFilter SET, AND WALL MOUNT BRACKET
Enjoy virtually uninterrupted air purification by ordering
an extra ESP cell and pre-filter set today. This way
you can always have a clean and thoroughly dry set
available to insert into your PurePro® professional air
purifier whenever the other ESP cell and pre-filter are
being cleaned and thoroughly dried.
Also available is the convenient PurePro® professional
air purifier wall mount bracket. This allows you to mount
your PurePro® professional air purifier up and out of
the way while still keeping the air in your room clean
and fresh.
Visit our website at www.thepurepro.com or call
1.800.875.8577 to order your new ESP cell, pre-filter,
and wall mount bracket today.
Remedy
Trouble
Indication
light won’t go
on
Turn off, unplug
and clean using
instructions from the
“CLEANING &
MAINTENANCE”
section.
Clean and dry
Too much dust has
ESP cell and
accumulated or inpre-filter thoroughly.
ternal parts are wet.
Keep the machine dry.
Check to see that the
ESP cell and
ESP cell and pre-filter
pre-filter are not
completely inserted. are completely seated
in housing.
Oxygen Plus™ filter
is not completely
inserted.
Check to see that the
Oxygen Plus™ filter is
completely seated in
housing.
*See “CLEANING & MAINTENANCE” section
15
ONE YEAR LIMITED WARRANTY
Your PurePro® professional air purifier is warranted to
be free from defects in materials and workmanship for
one year from the original purchase date Should the
product have a defect in materials or workmanship,
we will repair or replace it without charge to you (a
shipping and processing fee may apply). To obtain
service under warranty, simply call our Customer
Service Center toll-free at 1.800.875.8577.
This warranty does not cover damage caused by
accident, misuse or any use other than as intended
and described in this product manual, or damage
resulting from failure to maintain and clean this
product as specified in this product manual. This
warranty applies only to the original purchaser of the
PurePro® professional air purifier.
Contact Info for Warranty Service:
P.O. Box 4136
Hollywood, CA 90028
1.800.875.8577
www.thepurepro.com
© 2006-2008 Ionic Pro, LLC.
All Rights Reserved.
European Registered Design No. 506308.
U.S. Patent No. D544,948; Chinese Patent No. ZL200630014052.0;
Hong Kong Patent No. 0600746.8; Taiwan Patent No. D115,515
Additional patents pending
The energy efficiency of this ENERGY STAR qualified model is measured
based on a ratio between the model’s CADR for Dust and the electrical
energy it consumes, or CADR/Watt.
16
ARBITRATION AGREEMENT
THIS ARBITRATION AGREEMENT (THE “AGREEMENT”) AFFECTS YOUR LEGAL RIGHTS AND REMEDIES
BY PROVIDING THAT DISPUTES BETWEEN YOU AND THE SELLER OF THIS PRODUCT (“COMPANY”),
MUST BE RESOLVED THROUGH BINDING ARBITRATION, RATHER THAN IN A COURT. PLEASE READ
THIS AGREEMENT CAREFULLY. YOU ACCEPT THE TERMS OF THIS AGREEMENT BY RETAINING THE
PRODUCT(S) SHIPPED IN CONNECTION WITH THIS AGREEMENT (THE “PRODUCT”) FOR MORE THAN
FOURTEEN (14) DAYS AFTER RECEIPT. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT,
YOU MAY RETURN THE PRODUCT TO COMPANY WITHIN FOURTEEN (14) DAYS OF RECEIPT AT NO
COST TO YOU.
1. RESOLUTION OF CLAIMS OR DISPUTES. Any claim or dispute between you and Company
(or any of Company’s subsidiaries or affiliates) arising out of or relating in any
way to the Product or this Agreement shall be resolved through final, binding
arbitration. This arbitration obligation applies regardless of whether the claim
or dispute involves a tort, fraud, misrepresentation, product liability, negligence,
violation of a statute, or any other legal theory. Both you and Company specifically
acknowledge and agree that you waive your right to bring a lawsuit based on such
claims or disputes and to have such lawsuit resolved by a judge or jury.
2. LIMITATION OF LEGAL REMEDIES. All arbitrations under this Agreement shall be
conducted on an individual (and not a class-wide) basis, and an arbitrator shall
have no authority to award class-wide relief. You acknowledge and agree that this
Agreement specifically prohibits you from commencing arbitration proceedings as a
representative of others or joining in any arbitration proceedings brought by any
other person.
3. ARBITRATION PROCEDURES.
a. Before commencing any arbitration proceedings under this Agreement, you must
first present the claim or dispute to Company by calling 818-217-2500 and asking for
the Legal Department and allowing Company the opportunity to resolve the claim
or dispute. If your claim or dispute is not resolved within sixty (60) days, you may
commence arbitration proceedings in accordance with the terms of this Agreement.
b. The arbitration of any claim or dispute under this Agreement shall be conducted
pursuant to the American Arbitration Association’s (“AAA”) United States Commercial
Dispute Resolution Procedures and Supplementary Procedures for ConsumerRelated Disputes. These rules and procedures are available by calling the AAA or by
visiting its web site at www.adr.org.
c. The arbitration of any claim or dispute under this Agreement shall be conducted
in the State of California or the location in which you received this Agreement.
d. All administrative expenses of arbitration proceedings commenced under this
Agreement shall be divided equally between you and Company, except that: (a) if the
claim or dispute that is the subject of the arbitration proceedings is less than ten
thousand dollars (US$10,000), you will be responsible for no more than one hundred
twenty-five dollars (US$125) in administrative expenses; (b) if the claim or dispute
that is the subject of the arbitration proceedings is more than ten thousand
dollars (US$10,000) but less than seventy-five thousand dollars (US$75,000), you will
be responsible for no more than three hundred seventy-five dollars (US$375) in
administrative expenses; and (c) if the claim or dispute that is the subject of the
arbitration proceedings is more than seventy-five thousand dollars (US$75,000),
then you will be responsible for administrative expenses in accordance with the
Commercial Fee Schedule provided by the AAA. You acknowledge and agree that each
party shall pay the fees and costs of its own counsel, experts and witnesses.
4. CHOICE OF LAW. This Agreement shall be governed by the United States Federal
Arbitration Act and the laws of the state of California.
5. SEVERABILITY. If any provision of this Agreement is declared or found to be
unlawful, unenforceable or void, such provision will be ineffective only to the
extent that it is found unlawful, unenforceable or void, and the remainder of the
provision and all other provisions shall remain fully enforceable.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising