Whirlpool WDT710PAHZ, WDF130PAHW, WDT730PAHW, WDF330PAHW, WDF330PAHB, WDT730PAHB, WDT730PAHZ, WDF330PAHS, WDT710PAHW, WDF130PAHS Operating instrustions

Whirlpool WDT710PAHZ, WDF130PAHW, WDT730PAHW, WDF330PAHW, WDF330PAHB, WDT730PAHB, WDT730PAHZ, WDF330PAHS, WDT710PAHW, WDF130PAHS Operating instrustions
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
WATER SUPPLY REQUIREMENTS
DRAIN REQUIREMENTS
dishwasher has a water heating feature and also
requires a connection to a hot water supply line.
■■ A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure can be verified by a licensed plumber.
■■ 120°F (49°C) water at dishwasher
■■ 3/8" O.D. copper tubing with compression fitting or flexible
braided water supply line. See the “Tools and Parts” section
at the front of the guide for part details and orders.
NOTE: 1/2" minimum plastic tubing is not recommended.
■■ A
■■ A
WDF110PAB
WDF111PAB
WDF120PAF
WDF121PAF
WDF130PAH
WDF131PAH
WDF320PAD
WDF330PAH
WDF331PAH
WDF520PAD
WDF540PAD
WDF545PAF
■■ This
WDT710PAH
WDT720PAD
WDT730PAH
WDT735PAG
WDT735PAH
new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher. See
the “Tools and Parts” section at the front of the guide for part
details and orders.
■■ Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
■■ Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20" (508 mm) above
subfloor or floor.
Use of air gap
Air gap
90° elbow with 3/4" hose connection with rubber washer.
See the “Tools and Parts” section at the front of the guide
for part details and orders.
■■ Do not solder within 6" (152 mm) of the water inlet valve.
■■ If installed in new construction, make sure the house
water supply lines have been flushed prior to connecting
the dishwasher to remove any debris that may exist in
the supply line.
NOTE: If replacing an existing dishwasher, it is recommended
to install a new water line (see the “Tools and Parts” section at
the front of the guide for part details) and drain hose (supplied)
with the new dishwasher.
ELECTRICAL REQUIREMENTS
You Must Have:
■■ 120-volt,
60 Hz, AC-only, 15- or 20-amp, fused
electrical supply
■■ Copper wire only
■■ A maximum of 2 field wiring supply conductors
(12 AWG largest size) plus 1 grounding conductor
are permitted in the terminal box.
We Recommend:
■■ A
■■ A
time-delay fuse or circuit breaker
separate circuit
If Connecting Dishwasher with a Power Cord:
■■ Use
■■ If
required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap, a rubber hose (not provided) will
be needed to connect to the waste tee or disposer inlet.
■■ Use 1/2" minimum I.D. drain line fittings.
a UL Listed power cord kit marked for
use with dishwasher. See the “Tools and
Parts” section at the front of the guide for
part details and orders.
■■ Plug into a grounded 3 prong outlet. Outlet
must meet all local codes and ordinances.
If Connecting Dishwasher with Direct Wiring:
■■ Use
flexible, armored, or nonmetallic
sheathed copper wire with grounding wire
that meets the wiring requirements for
your home and local codes and ordinances.
■■ Use a UL Listed/CSA Approved metallic strain relief.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 1 of 2
W10806908-D-WH
12/16
PRODUCT AND CABINET OPENING DIMENSIONS
251/4"
(641 mm)
3/4"
(19 mm)
A
B
30"
(762 mm)
33/4"
(94 mm)
21"
(533 mm)
For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm).
A. Insulation may be compressed (not used on all models).
B. Door handles may protrude forward of the face of the
dishwasher, (varies by model).
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
34"
(864 mm)
C
101/2"
(267 mm)
4"
(102 mm)
63/4"
(172 mm)
3"
(76 mm)
24"
(620 mm)
21/4"
(64 mm)
13/4"
(44 mm)
NOTE: Shaded areas
of cabinet walls
show where utility
connections may
be installed.
61/4"
(159 mm)
2"
(51 mm)
24"
(620 mm)
D
C. Measured from the lowest point on the underside
of the countertop. May be reduced to 331/2"
(851 mm) by removing the wheels and perforated
area of insulation (blanket) on dishwasher.
D. Minimum, measured from narrowest point
of opening.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
Page 2 of 2
W10806908-D-WH
12/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement