General Bulletin
IMPORTANT:
Please
read this bulletin and
pass on to others in your
organisation.
General Bulletin
REFRIGERATION
Ice Maker & Water Dispenser Hardware List
MARKETS:
MODELS:
USA
ICE & WATER MODELS - E522B, RF201A
The following is a list of common hardware compounets used with the Fisher & Paykel Manufactured Ice and Water refrigerators.
Part
Description
¼ Hose White 4 meters
Part Number
836857
5/16 Hose Blue
837162
Flow mate Water pressure reducing Valve USA
836858
¼ Connector 90° Elbow John Guest Fitting
837192
¼ Connector straight John Guest Fitting
374049
Fisher & Paykel Appliances Ltd
78 Springs Road, East Tamaki, PO Box 58-732, Greenmount,
Auckland, New Zealand, Ph: 09 273 0600, Fax: 09 273 0656
Fisher & Paykel Customer Services Pty Ltd
A.C.N. 003 3335 171, 19 Enterprise Street, Cleveland, QLD 4163
PO Box 798, Cleveland, QLD 4163, Ph: 07 3826 9100, Fax: 07 3826 9164
Fisher & Paykel Appliances
150 Ubi Avenue 4, Sunlight Building #02-00, Singapore 408825
Ph: 6547 0100, Fax: 6547 0123
Fisher & Paykel Appliances Inc
5800 Skylab Road, Huntington Beach, California, CA92647, USA
Ph: 888 936 7872 (F&P), Ph: 888 396 2665 (DCS)
Fisher & Paykel Appliances Ltd UK
Maidstone Road, Kingston, Milton Keynes, MK10 0BD, UK
Ph: 44 1676 531 770, Fax: 44 1676 531 771
NZ = New Zealand
AU = Australia
ROW = International Markets
USA = United States of America & Canada
GB or UK = Great Britain & Northern Ireland
EU = Europe
IE = Ireland
TW = Taiwan
JP = Japan
Page 1 of 3
G-FRFD-07-02
JUNE 2007
Copyright © Fisher & Paykel 2007. All rights reserved.
Tap connection 7/16 to ¼ John Guest USA
312198
Clip collet locking PIC1808R John Guest tube Retainer 1/4
837193
Filter cartridge replacement
836848
Filter Body Head
836855
Complete filter Kit USA
836847
Water Tank
836846
Power control 110 volt 60 Hz USA
814529USP
Power control module 120 volt 60Hz - Non RoHs
MODEL RF201A USA
817858
Kit contains filter body & head
Pressure reducing Valve
Tap connection
¼ Hose White
Clip collet locking
PAGE 2 OF 3
G-FRFD-07-02
JUNE 2007
Copyright © Fisher & Paykel 2007. All rights reserved.
Ice maker PCB board
814856P
Water inlet valve dual
814859
Display Module LCD
814857P
Flow Sensor
836935
PAGE 3 OF 3
G-FRFD-07-02
JUNE 2007
Copyright © Fisher & Paykel 2007. All rights reserved.
IMPORTANT:
Please
read this bulletin and
pass on to others in your
organisation.
Service Bulletin
REFRIGERATION
Refrigeration Surround Kits
MARKETS:
MODELS:
USA
E521T, E522B, RF201
The refrigeration division have introduced a number of surround kits to suit Stainless cabinets. These can
range from two 790mm wide cabinets placed side by side to a single 790mm or 900mm wide cabinet.
The kits are to be supplied in Brushed Stainless steel for product ranging in height between 1695 –
1780mm (66¾ to 70 inches).
When choosing a single kit it is important to obtain the correct kit, for example, if the cabinet is hinged RH,
order the Right Hand kit.
The differences between the single and side-by-side kits are that the top trim is notched to take the hinge
cover.
Cabinets placed side by side will need to have had a Joiner Kit part number 813690 fitted to the cabinets
as well.
Part number
Brushed Stainless steel
Kit surround 1 x 790 LH
Kit surround 1 x 790 RH
Kit surround 2 x 790
Kit surround 1 x 900
(31 ¼”)
(31 ¼”)
(31 ¼”)
(35 ½”)
818758
818762
818759
818763
NOTE: Instructions attached (as per Instruction Sheet – part number 819150)
Fisher & Paykel Appliances Ltd
78 Springs Road, East Tamaki, PO Box 58-732, Greenmount,
Auckland, New Zealand, Ph: 09 273 0600, Fax: 09 273 0656
Fisher & Paykel Customer Services Pty Ltd
A.C.N. 003 3335 171, 19 Enterprise Street, Cleveland, QLD 4163
PO Box 798, Cleveland, QLD 4163, Ph: 07 3826 9100, Fax: 07 3826 9164
Fisher & Paykel Appliances
150 Ubi Avenue 4, Sunlight Building #02-00, Singapore 408825
Ph: 6547 0100, Fax: 6547 0123
Fisher & Paykel Appliances Inc
5800 Skylab Road, Huntington Beach, California, CA92647, USA
Ph: 888 936 7872 (F&P), Ph: 888 396 2665 (DCS)
Fisher & Paykel Appliances Ltd UK
Maidstone Road, Kingston, Milton Keynes, MK10 0BD, UK
Ph: 44 1676 531 770, Fax: 44 1676 531 771
NZ = New Zealand
AU = Australia
ROW = International Markets
USA = United States of America & Canada
GB or UK = Great Britain & Northern Ireland
EU = Europe
IE = Ireland
TW = Taiwan
JP = Japan
Page 1 of 1
S-FRFG-07-06
JUNE 2007
Copyright © Fisher & Paykel 2007. All rights reserved.
Fisher & Paykel – Refrigerator Surround Kit, Installation Instructions
This kit is designed to be used with models with a cabinet height of between: 1695mm to 1780mm (66 3/4” to 70 1/8”),
incorporating the “B” series refrigerators onwards - with curved & flat door styling. You can find the Part Number for each
installation type on page 4. To give the most integrated look, the kitchen cabinetry should be flush with the front of the
refrigerator door.
This kit can be used for combining any of the following refrigerators: – E388, E450, E402B, E411T, E415H,
E440T, E442B, E521T, E522B, RF610A, RF540A, RF201A.
Tools Required (not included)
1.
2.
3.
4.
5.
No. 2 square type drill bit - long
Electric drill
Flat blade screwdriver
1 x 16mm (11/16in) piece of MDF the same size as the base of the cavity.
Joiner kit (part number 813690) required if joining two refrigerators side by side.
Parts Included in Kit
2. Top Trim Brackets
* Part shown is for 2 x Side By Side.
If you need assistance please call your Fisher & Paykel Customer Care Centre. A Customer Care operator
will provide expert guidance and if necessary can organise a Service Technician visit ensuring the correct
installation is achieved. (A service fee will be charged).
4. Side Trim Brackets
4. Side Trim Brackets
3. Side Trim
3.
4.
5.
6.
1. Top Trim
Top Trim (x 1)
Top Trim Brackets:
– Single Refrigerator Kits (2 x brackets)
– Side by Side Kits (2 x brackets)
Side Trim (x 2)
Side Trim Brackets (x 10)
Bottom Trim (x 1)
Screw Type A: #8x12 Square Drive CSK (x 26)
3. Side Trim
1.
2.
5. Bottom Trim
Australia
New Zealand
Canada and USA
Singapore
UK
Ph: 1 300 650 590
Ph: 0800 37 2273
Ph: 1.888.936.7872
Ph: +65 6741 0777
Ph: +44 0845 066 2200
06/2007
Part Number 819150
Installation Procedure
Step 1
1
Check that the internal Cupboard Cavity dimensions are correct (see diagram 1).
2
Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual cartons for unpacking procedures).
3
Ensure the floor and/or the cupboards are protected from damage during the unpacking and assembly of the cabinets.
4
Check the refrigerator and freezer doors are hinged on the desired side.
5
Check that the kit is complete (refer to kit parts list on page 1).
Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken with a minimum of two able-bodied persons.
Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient operation of the refrigerator.
Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 5 or installed above the toe kick board as in diagram 4.
The placement of the 16mm MDF or plywood under the cabinet or cabinets on either installation type is to allow the fitment of the Bottom trim that covers it.
Noting cabinets installed above the toe kit should have a floor base constructed, to support the total weight of the loaded cabinet or cabinets placed on it.
1
Diagram 1: Cutout Dimensions (flush to edge of door)
All Dimensions are quoted in millimetres & inches
Width of models mm - inch
Width A
Depth B*
Height C
Air Vent D
790 model
962 - 37 7/8”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
900 model
1072 - 42 1/4”
700 - 27 9/16”
1891 - 74 1/2”
200 - 8”
635 model + 635 model
1467 - 57 49/64”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
680 model + 680 model
1557 - 61 19/64”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
790 model + 790 model
1777 - 70”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
* Depth is a minimum requirement
Cut out dimensions above are to be used as minimum dimensions.
Step 2
1
Locate the two/three top trim brackets.
2
For the Side By Side Refrigerator kits, one bracket is to be screwed in the top centre of the cabinet, secure the top bracket with two of the screws
(Type A, #8 x 12 SQ Drive CSK).
3
For all kits, the remaining two brackets are to be secured on either side, by two screws which are mounted from the side (see diagram 2).
4
Looking at the front of the product, place the top brackets on top of the wooden cabinet.
5
Care must be taken to line up the top front edge of the brackets with the leading edge of the cabinet.
2
Diagram 2: Top Trim Brackets
END BRACKET
CENTRE BRACKET
Step 3
1
Locate the ten side trim brackets.
2
Position five brackets to the left hand side of the cabinet’s and the remaining five brackets to the right hand side of the cabinet’s.
3
Brackets should be evenly spaced down each side (see diagram 3). Secure each of these brackets with the two screws provided.
4
Care must be taken to line up the front edge of the brackets with the leading edges of the cabinet.
3
Diagram 3: Side Trim Brackets
Step 4
Place 16mm (5/8in) piece of Plywood or MDF the same size as the base of the cavity into cavity. See diagram 4.
4
Diagram 4: MDF Board
5
Diagram 5: Trim Installation
16mm (5/8in) Plywood or
MDF board Insert
Step 5
1
2
3
4
Remove protective coating film from surround trim.
To install the surrounds, first clip in top surround.
Ensure the locater strips at the rear of the top brackets clip into the rear of the top trim, then clip both side trims into place starting
from the front cabinet edge.
Lastly install the bottom trim. The bottom trim requires an 16mm (5/8in) piece of MDF the same size as the base of the cavity to sit on. See
diagram 4.
Step 6
1
2
3
If installing two refrigerators/freezers side by side a joiner kit is required (part number 813690). Refer to these instructions and fit joiner kit
before pushing refrigerator into place, see diagram 5.
Plug refrigerator into electrical socket, run water connection to refrigerator if required (Ice & Water models only).
Gently install refrigerator into cabinetry making sure it is centred within the surround trim.
The front of the refrigerator door should be flush with the front of the cabinetry to obtain an integrated look.
Kit Part Numbers and Cut Out Dimensions Table
Part Numbers
Refrigerator Model Width
1 x 790 LH
962
Iridium Stainless
818 758
814 678
818 759
814 679
818 760
Cut Out Dimensions
Plus Joiner Kit
Width A
Depth B*
Height C
962mm
37” 7/8
700mm
27” 9/16
1806mm
71” 1/8
813690
1777mm
70”
700mm
27” 9/16
1806mm
71” 1/8
814 680
813690
1557mm
61” 19/64
700mm
27” 9/16
1806mm
71” 1/8
818 761
814 681
813690
1467mm
57” 49/64
700mm
27” 9/16
1806mm
71” 1/8
818 762
814 682
962mm
37” 7/8
700mm
27” 9/16
1806mm
71” 1/8
818 763
814 683
1072mm
42” 1/4
700mm
27” 9/16
1891mm
74” 1/2
1806
Brushed Stainless
2 x 790
1777
1806
2 x 680
1557
1806
2 x 635
1467
1806
962
1 x 900
1072
1806
1 x 790 RH
1891
* Depth is a minimum requirement
If you need assistance please call your Fisher & Paykel Customer Care Centre. A Customer Care operator
will provide expert guidance and if necessary can organise a Service Technician visit ensuring the correct
installation is achieved. (A service fee will be charged).
Australia
New Zealand
Canada and USA
Singapore
UK
Ph: 1 300 650 590
Ph: 0800 37 2273
Ph: 1.888.936.7872
Ph: +65 6741 0777
Ph: +44 0845 066 2200
06/2007
Part Number 819150
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement