Advertisement
Advertisement
S 3 7 5 0 T H S
U S E R
G U I I D E
1.1 DATE: 2004
Page 1
Table of Contents
Getting Started:
Declaration of Conformity
General
Note
1.1 Unpacking the printer
1.2 Installing and Charging the Battery
1.3 Reading the LED Status
1.4 Attaching Belt Loop System
Loading Supplies:
2.1 Adding
2.2 Tearing
Using the Printer:
3.1 Initial power up and self-test
3.2 Connecting the Printer
3.3 Communications: Serial RS232C
IrDA
3.5 Communications:
3.6 Using the Magnetic Card Reader information
Printer Maintenance
4.1 Cleaning
4.2 Charging the Printer Battery
4.3 Verifying Battery Charge State
4.4 Battery and Safety Information
4.5 Recycling your Batteries
4.6 Trouble
Supplies
Specifications:
Specifications
5.2 Supply
18
18
19
19
20
20
21
22
22
23
Page 2
10
11
13
14
14
14
15
5
7
8
3
4
4
5
8
9
Provisional Declaration of Conformity
Name:
Manufacturer’s Address
Extech Instruments Corporation
285 Bear Hill Road, Waltham, MA 02451, USA
Telephone: +1 781 890 7440
Declares that the Product
Product Name: Portable Receipt Printer
Model Number: S3750THS;
Optionally Containing: 1)Bluetooth™ radio short range OEM module from connectBlue ab, cB-0701-01; FCC ID PVH 070101.
Conforms to R&TTE Directives: 1999/5/EC (EN 300 328-
Conforms to the following regulation and/or standards:
2), EMC Directive 89/336/EEC (EN 301 489-1 and -17); and
Low Voltage Directive 73/23/EEC (EN 61131-2)
3)802.11 Wi-Fi Module
FCC: Part 15 Subpart B, Class B
CE: EN55022 Class B;
CE: EN61000-3-2;
CE: EN61000-3-3 ;
CE: EN50024.
Supplementary Information : • The product complies with EMC Directive
89/336/EEC and Low Voltage Directive
73/23/EEC
• The product conforms to ANSI/UL STD 60950 &
Certified to CAN/CSA STD C22.2 No. 60950-00
• CB Certified
• ETL Listed, control # 3046813
• The product is IEC 68 certified
Date:
Signature:
Antony Revis, General Manager
Page 3
General Precautions
• Before using this product be sure to read through this manual. After reading please keep the manual in a safe place for future reference.
• The information contained herein is subject to change without notice of any type.
• Extech is not responsible for any operational results regardless of missing information, errors or any misprinting in this manual.
• Extech is not responsible for problems created as a result of using options and consumables not approved by them.
• This product is designed for servicing at an Authorized Service Center. Other than routine maintenance described in this manual the user should not attempt to repair, service or disassemble this product.
• Incorrect operation, handling or improper operating environments may cause damage or otherwise affect the proper operation of this product. Such actions invalidate the product warranty.
Safety
In this manual and on the Printer and accessories we make use of internationally recognized safety symbols as follows:
!
Caution! Refer to the explanation in this Manual
Caution! Risk of electric shock
Double Insulation or Reinforced insulation
DC, Direct Current or Voltage
AC+DC, Current or Voltage
Page 4
1. Getting Started
1.1 Unpacking the Printer:
The S3750THS portable printer is a full featured portable receipt printer designed for varied job environments including field service, field sales, hospitality and restaurants, ticketing and many others where point of service receipts are required.
The package contains:
printer:
battery cartridge,
AC input, DC output wall mounted charger (may be USA, European or UK style plug) for charging the battery inside the printer
belt loop system and
roll of paper supply (already loaded in the printer).
Both cabled and wireless communication is possible.
1.2 Installing and Charging the Battery Cartridge:
Note: One battery cartridge is included with the printer. Similar to a cordless phone battery, the printer’s battery must be charged before using it.
!
Extech batteries must be cycled several times to achieve maximum capacity. To cycle a battery fully charge it and then allow full discharge through normal use in the printer.
1 1 .
.
2 .
.
1 : : I n s t a l
Note: Refer to Figure 1 below to install the battery pack in the printer. l l l i n g t h e b a t t e r y
Unlock the battery door by sliding the battery door locking tab down
Open the battery door
Insert the battery as shown. The battery side with two contact terminals should be facing down to make contact with the two spring probes inside the battery compartment.
Close the battery door.
Lock the battery door by sliding the battery door locking tab up
Page 5
F i i g u r r e 1 : I n s t a l l l l i i n g t h e B a
C a r t a t r r t i i t e d r g y e
1 .
.
2 .
.
2 C h a r g i i n g t h e B a t t e r y
Charge the battery by inserting the wall mounted charger line cord into the printer jack. Then insert the charger plug into an appropriate wall socket.
The Yellow/Amber charging LED will illuminate indicating that the battery is being charged
The battery will be fast charged and after about 180 minutes the LED will go off
To remove the battery cartridge, open the battery door and tip the battery out of the printer
.
Note: To ensure a full charge do not operate the printer while charging.
Note: The wall mounted charger is a Class II equipment (
)
. Multiple plug configurations comply with most international standards.
S3750THS
Input Voltage/Current 100-240 VAC/0.5A
Input Frequency
Output Voltage/Current
47-63 Hz
10VDC/1A
(
)
Note: The wall mounted charger is not supplied with plugs for use in Korea.
!
Do not use a charger not approved by Extech for use with the
S3750THS. Use of an unapproved charger could damage the battery pack or the printer and will void the warranty.
Page 6
!
!
The battery terminals are well recessed inside the printer. Do not allow them to contact conductive material since this may create a short circuit which could cause injury or start a fire.
When using the wall mounted charger ensure the socket outlet is close to the printer and easily accessible during the battery recharging process. Either switch the socket off (if supplied with a socket switch) or pull out the charger from the socket or disconnect the plug from the printer in the event of any problems.
1.3 Reading the LED Status:
This table explains the LED indicator status. Refer to Figure 1 for the locations described for ON/OFF and FEED pushbutton switches and AC adaptor socket .
LED Indicator State Status
LED # 1
ON - YELLOW
If the LED’s Color is YELLOW, it indicates Low Power
LED # 2
LED # 3
ON - GREEN
ON - BLUE
ON - YELLOW
If the LED’s Color is Green it indicates that Power is ON and that the printer is in RS232 or IrDA mode
If the LED’s Color is Blue it indicates that Power is ON and that the printer is in Bluetooth or
802.11b mode
The battery charger is charging the battery at a fast rate. If the battery is below 5V, the battery is being
“trickle” charged until the battery voltage reaches 5V, and then the fast charge rate is started. The LED will turn off when the battery is
fully charged.
ON -GREEN
ON - RED
Indicates that MCR is ready to accept data.
Indicates that SCR is ready to accept data.
Indicates a fault condition or a printer error. The printer is not ready to accept data.
Printer is out-of-paper
Note: Refer to the troubleshooting guide to determine error or fault condition.
Table 1 - Reading the LED Status
Page 7
1.4 Attaching Belt Loop System:
The belt loop system consists of two parts:
A knob located on the back part of the printer just above the battery door
A strap with click on connector
To attach the strap to the knob insert the knob located at the bottom of the printer into the slot of the connector. Pull down until you hear a click. The printer is now secure. The loop is then placed over your belt. Allow the printer to hang down to either the left or right hip.
To release the printer, press in on the two latches on the connector and pull the knob clear of the slot.
Note: Do not force or pull the printer from the connector without pressing
in on the two latches
2. Loading Supplies
2.1 Adding Paper/Labels:
The printer can print text, bar codes and graphics on thermal receipt paper. See
“Supply Specifications” for the width, thickness requirements and approved vendors. Follow these steps to load printer paper.
Open the paper supply cover by placing your fingers under the “T” pull lever and pulling up firmly on the supply cover until the lever stops moving.
DO NOT pull too hard. Use enough force to allow the cover to unlock and lift freely
DO NOT force the “T” pull lever too far back
Place the paper supply roll into the paper supply well. Make sure the paper supply unwinds from the bottom as shown in Figure 3
Position the paper supply between the print head guides
Make sure some supply (2-3 inches) extends beyond the top of the paper supply well
Close the paper supply cover and press close.
Page 8
F i i g u a
O n p d e r r a t t o
P a p e r r C o n r r e 3 e r r L o n t t r o a d i i n
: n s g r o
: o l l s
2.2 Tearing Paper:
The printer’s paper door acts as a tear bar. Pull one edge of the paper against the tear bar as indicated, then tear down and across against the tear bar to tear the paper.
!
Caution: The tear bar may have sharp edges.
Using the tear bar is the only way to tear the paper.
Pulling up and pulling sideways without using the tear bar can cause a paper jam due to paper misalignment in the print head mechanism.
T e a
F i i g u r r e 3 A r r i n g P a p
A : e
: e r r
Page 9
3. Using the Printer
3.1 Initial power up and self-test
Once the Battery is charged and the paper is loaded perform a self-test:
Press the <On/Off> switch once. This turns printer on. LED #1 illuminates in green or blue depending on the mode of communication.
After approximately 20 seconds, if no instructions are sent to the
printer, the printer automatically turns off to conserve battery life.
If the printer is set for infrared communications (IrDA) mode the printer will stay on all the time. Pressing the <On/Off> switch again will turn the printer off.
Press the <On/Off> switch to turn the printer off. The LED turns off.
To start the self-test, press and hold the <FEED> switch then press the
<On/Off> switch
The printer starts to print the self-test message. Release the <FEED> switch.
Press the <On/Off> or <FEED> switch to cancel the self-test print.
The first few lines of self-test show the printer firmware version, the current printer settings (for example IrDA or Serial mode) and a list of any optional or special features installed.
F
i
i g u r e 5 – S a m p
l
l
e
S e
l
l f T e
s t
t
Page 10
3.2 Connecting the Printer
The S3750THS printer supports Serial RS232 and IrDA compatible infrared communication interfaces. Radio frequency (RF) communication is also available as an optional feature as well as 802.11b interface.
Serial, IrDA , 802.11b and Bluetooth communication settings can be changed via a DIP switch located on the control card.
The DIP switch is located inside the battery compartment as illustrated below indicating the location of this switch. Figure 2 shows the DIP switch selection.
The functions assigned to these switches are shown in Table 2.
If the Serial interface is selected, the communication Parameters, Baud rate,
Data Bit and Parity, must be set. These parameters apply both for UART 1 and UART 2.
Note: Optional serial cable is available for Serial RS232 communication (part # 5892RJD9).
Printer drivers for Windows 95/98/NT/2000 and XP are available from
Extech.
PrinterCE print Control utility is available from Extech for Windows CE devices.
Printboy Print Utility from Bachmann Software or PalmPrint Utility, from
StevensCreek, are recommended for Palm Pilot devices
D i i p S w i i t t c h
F
L i g o u c r r a e t t i i
2 : o
: n n
Page 11
3 .
.
2 .
.
2 S e t t t t i i n g D i i p S w i i t t c h e s
3 .
.
2 .
.
3 D i i
Note: Be careful when changing dip switch settings. Carefully use a pointer on the dip switch you are going to change. DO NOT use a screw driver or apply excessive force. p S w i i t c h F u n c t t i i o n s
Note:(Developer’s refer to Programming Manual for more information)
# Switch Switch # Notes
1 & 2 & 3 Communication Interface SW1 SW2 SW3
On Fixed 9600Baud for
Firmware version 0.5
4 & 5 Baud Rate SW4 SW5
6
7
Parity Bit SW6
Odd/Even SW7
Odd parity checker On
8 Auto Power Save SW8 firmware 118v0.5
Power save disabled On
Power save enabled Off
Table 2 – DIP Switch Setting
Please note: In order for changes to the dip switch configuration to take effect, the printer power must be reset.
Page 12
3.3 Communications:
The S3750THS Printer has two UARTs and that is why it is able to support two modes of communication simultaneously – Either RS232 and
IrDA ( If Dip switch # 1 is ON) or RS232 and 802.11b /BT (If Dip switch # 1 is OFF and Dip Switch # 3 is ON). Dip Switch # 2 is used to control the
RS232 Port. If the Switch is turned ON the RS 232 port is disabled and if it is turned OFF the RS232 Port is enabled. The reason why sometimes it is necessary to disable the Serial Port is that turning it off brings substantial power savings and hence a longer battery life. There is an option between
Bluetooth / 802.11b. The printer can have either one enabled but not both of them at the same time.
Serial
The RS232C Interface signals for the S3750THS Series printers are terminated on a 6 PIN RJ type data connector located on the side of the printer.
Six connections are provided from the Serial Interface to the host computer.
The TABLE 3 below lists the Serial Interface signals and pin outs on the RJ connector and the connector pin locations are shown in FIGURE 6.
A minimum of two connections are required for operation: RXD – pin 3 and
Common – pin 1
The communication Parameters: Baud rate, Data Bit and Parity must be set same as the host device settings.
FIGURE 6 – RJ DATA CONNECTOR
TABLE 3 - 3 7 5 0 T P r i i n t t e r s ’ S e r r i a l l R S 2 3 2 C I I n t e r r f a c e s i g n a l l s
Page 13
3.4 Infrared Communications Mode (IrDA Only) :
Dip Switch #1 and # 2 must be in the <ON> position
The printer can be powered up by pressing the power <On/Off> switch
If no IrDA connection is made, the printer will automatically power down to a lower power level to conserve battery life. It will remain in a “sleep” mode until an IrDA connection is made, at which time the printer will “wake” up and print the requested data
Pressing the power switch again will turn the printer <OFF>.
3.5 Bluetooth/802.11b Communications Only (Option):
Dip Switch #1 must be in the <OFF> position
Dip Switch # 2 and # 3 must be in the <ON> position
Note:Since UART 1 (RS232) and UART 2 (IrDA/BT/802.11b) share the same Dip Switches, the same baud rate , parity and stop bits settings apply both for RS 232 and BlueTooth/802.11 (Refer to Developer’s
Manual for further details)
Note: Adjust settings to match those of the BT or 802.11b module in your computing device
The printer can be powered up by pressing the power <On/Off> switch
Depending on Whether you have an 802.11b or a BLuetooth Module installed the printer will enter that state respectively.
Pressing the power <On/Off> switch again will turn the printer <OFF>.
Note: It is necessary for the mobile computing device you are using to discover the printer. Refer to instructions provided by the systems integrator.
Note: Systems Integrators: Refer to the Bluetooth manual provided with your mobile computer and the Bluetooth section of the Developer’s
Manual /802.11b Application Note available for this printer.
3.6 Using the Magnetic Stripe Reader:
The Magnetic Card Reader is a factory-installed option. This option requires special application software to read and process cards with a magnetic stripe, such as credit cards or driver’s license
Note: Refer to the Figure 4 if your printer is equipped with the optional magnetic stripe reader
Quickly swipe the card through the reader either left to right or right to left.
The magnetic stripe must be facing toward the paper supply door as indicated below while it is passed through the reader
Refer to Table 4 for the description of the LED indicator Status.
LED indicator
Green
Red
State
ON
OFF
ON
Status
Ready/waiting for card to be swiped.
Good swipe - Card data read OR
Card not ready to be swiped.
Error reading card’s data.
T a b l l e 4 M a g n e t i i c C a r d L E D I n d i i c a t o r
Page 14
F i i g u r r e 4 : U s i i n g
M a g n e t i i c C a r r d R e a t h e a d e e r r
3.7 Programming Information:
This section lists the printer control commands strings.
System Developers: Please refer to S3750THS programmer’s manual for further details.
Other features may be available and are described in the programmer’s manual
3.7.1 ASCII CONTROL CHARACTERS:
Character Hex/Dec
EOT 04/04
BS
HT
08/08
09/09
LF
VT
0A/10
0B/11
CONTROL ACTION
End Of Text
Back Space
Horizontal Tab
Line Feed
Vertical Tab
FF
CR
SO
SI
XON
AUXON
XOFF
NORM
AUXOFF
CANCEL
0C/12
0D/13
0E/14
0F/15
11/17
12/18
13/19
14/20
15/21
18/24
Form Feed
Carriage Return
Shift Out
Shift In
Transmitter On.
Printer on.
Printer receiver is off
Return to default 42 column mode
Printer to Host: printer is off
Cancel and reset printer BUFFER
EXTEND 1C/28
EXTEND OFF 1D/29
Extended print
Extended print off/Normal print
Page 15
3.7.2 Printer Font Commands – Courier Character Set:
Font Name Character size (W x H) Command String
24 CPI normal 8x23 ESC+'k'+'5'
21 CPI normal
19 CPI normal
16 CPI normal
12 CPI normal
13 CPI rotated
9x23
10x23
12x23
16x23
14x16
3.7.3 Printer Font Commands :
ESC+'k'+'4'
ESC+'k'+'3'
ESC+'k'+'2'
ESC+'k'+'1'
ESC+'k'+'0'
Command String
ESC - ‘F’ – 1
ESC - ‘F’ – 2
ESC - ‘U’ - ‘1’
ESC - ‘U’ - ‘0’
Printer Action
Selects International character set
Selects PC Line Draw character set
Enable emphasized print.
Disable emphasized print.
3.7.4 Printer Graphic Commands:
Command String
ESC - ‘a’ – n
ESC - ‘J’ – n
ESC - ‘P’ - ‘#’
ESC - ‘P’ - ‘$’
ESC - ‘V’ - n1 – n2
ESC - ‘v’ - n1 – n2
Printer Action
Select dot line spacing between printed lines.
Graphic Line Feed command
Select Online mode, characters printed as received.
Select Buffer mode, characters are printed on (^ D)
8-bit Graphic command
RLE Compressed Graphic command
3.7.5 Magnetic Card Reader Control Commands:
Command String
ESC - ‘M’ - ‘nnm’ - Cr
ESC – ‘C’
Printer Action
Select MCR with (nn) auto timeout
Cancel MCR read process
3.7.5.1 Smart Card Reader Control Commands (when SCR is installed):
Command String
ESC - ‘M’ - ‘nn’ - ‘7’- Cr
ESC - ‘M’ - ‘nn’ - ‘8’- Cr
Printer Action
Select SCR in direct mode with
Serial RS232 (UART0). (nn) is the auto timeout of the SCR.
Select SCR in PassThru mode with
BT/802.11 or IrDA on (UART1).
(nn) is the auto timeout of the SCR.
Page 16
3.7.6 Graphic Logo and Bar code commands:
Command String
ESC – L – G –n
ESC – G - 0x0FF
ESC – L – g – n
ESC - 'z' - n1 – n2 - L - [data]
ESC - 'Z' - n1 – n2 - L - [data]
ESC - ‘Q’ - ‘J’ – n
ESC - ‘Q’ - ‘Q’ – n
ESC - ‘Q’ - ‘F’ – m
ESC - ‘Q’ - ‘B’ – m
Printer Action
Prepare printer to load image:
Loading Logo Complete:
Print stored logo image:
Print Bar Code without visible text
Print Bar Code with visible text
Reverse Dot Feed
Set Out of Paper Sensitivity
Set Forward Black Mark Seek
Reverse Black Mark Seek
3.7.7 Printer Supervisory and Control Commands:
Command String Printer Action
^V Buffer, power timer & battery status
ESC - ‘P’ –‘^’
ESC – ‘P’ – alpha
ESC – ‘M’ - ‘000’ - Cr
ESC - ‘M’ - ‘nn0’ - Cr
ESC – ‘M’ - ‘C’
ESC – ‘P’ – ‘( ‘
ESC – ‘ P’ - ‘)’
Print Battery Voltage
Time and date print and control disable the power down timer sets the power down timer to nn seconds
Reset Auto power down to 20 seconds
Firmware version query
Hardware model query:
Resident Character Sets (characters 32 through 255):
Page 17
4. Printer Maintenance
4.1 Cleaning:
You may need to clean the print head and platen roller after printing a number of rolls of paper, whenever you load new supplies or when you see voids in the printout.
!
Caution: Do not use sharp objects to clean the print head. This may damage the printer and require service.
Open the paper door by pulling the “T” bar lever on the top cover as shown in Figure 3. The paper supply door will pop up.
Remove the paper roll.
Moisten a cotton swab with isopropyl alcohol and clean the print head
Clean the platen roller with a dry cloth or small brush
Note: You can also use another cotton swab moistened with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or
dry cloth across it. Make sure the platen roller is clean all the way around.
Moisten another cotton swab with isopropyl alcohol. Rub the swab across the black mark sensor to remove any build-up
Moisten another cotton swab and rub the swab across the tear bar to remove any build-up
Note: You may experience dust build-up depending on the environment and the quality of the paper supply you use. If this occurs, use a can of
compressed air to blow dust and paper debris out of the printer.
4.2 Charging the Printer Battery:
The printer battery is charged using the wall mounted charger provided. Follow these steps to charge the battery pack.
Plug the charger into an appropriate wall socket; then plug the charger line cord into the adapter jack on the side of the printer (see Figure 3)
The yellow CHARGE LED will illuminate, to indicate battery is charging
The Charge LED turns off when battery cartridge is fully charged. It takes about 180 minutes to fast charge the battery cartridge
To insure full charge, printer should not be operated while the battery is
4 .
.
2 .
.
1 I charging.
I m p o r r t a n t t N o t e s o n C h a r r g i i n g B a t t t e r r i i e s
The model S3750THS printers require an adaptor output of 10VDC/1.4A.
The battery Fast-charge is initiated each time the power adapter is connected to the printer
The fast-charge controller checks the battery’s voltage and temperature, before the start of the fast recharge process. If the battery voltage or the temperature is outside of the fast-charge limits, the charger defaults to trickle charge at C/10 or 70 mA rate
Optional external battery chargers are available for Extech batteries
Page 18
4 .
.
2 .
.
2 I m p o r r t t a n t N o t e s o n R e p l l a c i i n g B a t t e r i i e s
Check for the correct Extech part number for the battery and only order that part for your new battery
!
Caution: Risk of explosion if battery is replaced by an incorrect type.
!
Caution: Dispose of used batteries according to instructions in Section
4.5
4.3 Verifying Battery Charge State:
It is strongly recommended testing your printer before returning to Extech. Follow these steps to identify and correct any battery power problem that may be encountered. These will help to identify that the fault is with the printer and not some other part of your system.
To test the AC adaptor use a multi-meter and measure the output. Output should be 10VDC
Press the <ON/OFF> switch and wait until all LED’s are off
Insert the AC adaptor plug into the printer. If the amber LED goes on, the battery is not fully charged but the charge circuit is functioning.
The AC power portion of the circuit appears ok
Disconnect the AC Adapter once the battery has charged for 5 minutes or so.
Press and hold the <FEED> switch, then press and release the <ON/OFF> switch and then release the <FEED> switch. The printer will print a “self test” receipt
If the self test receipt is printed, the DC power is ok
Press <ON/OFF> switch and wait until all LED’s are off
Plug the AC adaptor into the printer. Press <ON>; the green LED is illuminated and after about 20 seconds the LED should go off
If the amber LED is on, this will continue on through this test indicating that the battery is accepting a charge and that the charge circuit is ok. At the end of a 180 minute charge cycle the LED will go off.
4.4 Battery and Safety Information:
The printer is powered by a 7.4V Li-Ion battery cartridge.
Charging time in the printer is approximately 3.0 hours
Take the battery out of printer if storing the printer for long periods of time
The battery storage temperature is 40°F to 104°F (4°C to 40°C). Do not store a fully charged battery at temperatures greater than 104°F (40°C) for long periods of time – the battery may permanently lose charge capacity
Be sure to use a fully charged battery before long or battery intensive printing sessions. Certain operations (for example, printing receipts with a lot of bar codes and graphics) drain the battery more quickly than others
Dispose according to your local regulations. Do not throw in trash
Caution: Do not disassemble, short circuit, heat above 80°C, or
incinerate. The battery may explode
The recommended temperature for charging is between 68°F (20°C) to 77°F
(25°C).
Page 19
4.5 Recycling your Batteries:
The Rechargeable Battery Recycling Corporation (RBRC) is a non-profit organization created to promote recycling of rechargeable batteries. For more information about how to recycle batteries in your area, visit www.rbrc.org
.
4.6 Trouble Shooting:
Problem
Does not feed paper or has a paper jam.
Does not print
Light printing
Voids in printing
Red (Error) LED on
Action
Remove any jammed supply
Reload paper supply.
Check or replace the printer’s battery
Make sure the paper supply is loaded correctly, not backwards.
Verify communication between the host device and the printer by disconnecting the communication cable and performing a printer self test.
Check or recharge the battery
Adjust the print contrast through print application.
Clean the print head following the cleaning
instruction listed in Cleaning section.
Check that paper roll is not out
Error reading MCR
After extended printing, print head may be hot; printer will pause before resuming printing.
If the problem is not identified following above trouble shooting guide, contact
Extech Technical Support. Support numbers and Email addresses are listed at www.Extech.com
.
Other than routine cleaning and other maintenance described in Section 4, the printer is not intended to be serviced by the user. It must be returned to an authorized service center . Under no circumstances should the user attempt to take the printer apart.
Page 20
4.7 Printer Supplies:
Part Number
757061
78428I1
78428I2
78428I4
78428I1R
7A1000014
157120
157220
157240
Available from Extech Email: [email protected]
Download: http://www.fieldsoftware.com/PrinterCE.htm
Download http://www.stevenscreek.com/pilot/dodownload.html
756998
5892RJD9
Description
S3750T Thermal paper pack (3”/80 mm, 5 rolls)
3750T PKG 120v (US Plug)
3750T PKG 220v (EURO Plug)
3750T PKG 120v (UK Plug)
3750T MCR PKG 240v (UK Plug)
3750T Li-Ion Battery Cartridge:
7.4VDC– 1800mA
Battery charger adapter 3750T
Input 120VAC/Output 10VDC @ 1.4A (US Plug)
Battery charger adapter 3750T
Input 220VAC/ Output 10VDC @ 1.4A (Euro Plug)
Battery charger adapter 3750T
Input 240VAC/ Output 10VDC @ 1.4A (UK Plug)
3750T User’s Guide
Windows 95/98/NT/2000/ Drivers
Windows CE print Utility
Palm Pilot print Utility
Belt Loop System
Serial Data Cable – RJ to DB9 PC compatible
Page 21
5 Specifications
5.1 Printer Specifications:
Height:
Width:
Length:
Weight: w/battery & supply
Shipping weight:
Power:
Operating Temp. Limits:
Storage Temp. Limits:
Operating Humidity Limits:
Storage Humidity Limits:
Print head:
Printing Method:
Print Speed:
Supported Fonts:
(Bitmap)
Supported Bar Codes:
Memory:
Charging Time:
Communications:
Print Ratio:
5.2 Supply Specifications:
Supplies:
Supply Thickness:
Supply Width:
Supply Length:
Supply Sensing:
Paper roll diameter:
Maximum Print Area:
Approved Vendors
2.25 inches (57mm)
4.25 inches (108mm)
6 inches (152mm)
1.41 lbs. (0.64 g)
3 lbs. (1.4 kg)
7.4 V Li-Ion battery
41F to 104F (5 to 40C)
-4F to 140F (-20C to 60C)
20% to 85% non-condensing
5% to 95% non-condensing
3 inches wide (80mm)
203 dpi (8 dots per mm)
Thermal Direct
Up to 2.0 inches per second
Standard (normal and bold)
Large (normal)
Reduced (normal and bold)
Large rotated.
Codabar, Code 39, UCC/EAN – 128,
UPC/EAN/JAN,
Interleaved 2 of 5, Code 128, PDF 417
512K SRAM, 32K Program Flash
224K Fonts and Logos Flash
Approximately 180 minutes
RS-232 port, IrDA, BT, 802.11b
25% black maximum/sq.in.
Thermal direct receipt paper
2.2 to 3.5 mils (receipt paper)
3.125 inches (80mm)
1 roll of receipt paper is approx. 600 inches (15,240 mm)
Black mark (on face of supply)
Outside: 1.375 inches (32 mm)
Inside: .25 inches (6 mm)
2.85 inches (72 mm) X 8.0 inches
(203mm)
Kansaki: P300, P310, P350, P354, P390,
P530UV, TO281CA, OP200, TO381N,
F180, F380, F550
Jujo: TF-50KS-E2C
Honshu: FH65BV-3
Page 22
5.3 Regulatory Notes:
5 .
.
3 .
.
1 F C C P a r r t 1 5 C l l a s s B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For Bluetooth equipped printers please note:
The printer contains an OEM Serial Port Adapter from connectBlue with FCC ID: PVH070101. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
5 .
.
3 .
.
2 W W a r r r a n t y :
This printer is warranted by Extech Data Systems to be free of defects in parts and workmanship for a period of one year from date of shipment. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. Extech specifically disclaims any implied warranties of merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, special, incidental or consequential damages. Extech’s total liability is limited to the repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral is expressed or implied.
Page 23
5 .
.
3 .
.
3 W a r r a n t y a n d / o r R e p a i i r S e r v i i c e : :
A Return Authorization number must be issued before a unit is returned to Extech for repair. Once a unit has been properly returned to Extech (Note: The customer is responsible for ensuring proper packing to prevent damage in transit as well as the shipping costs back to Extech), it will be repaired (estimates are provided first if the repair cost is estimated above $100.00) and returned via UPS ground. The customer may elect a faster mode of transport at their cost.
Page 24
Advertisement
