User manual | 1756-SG001 - Literature Library

Selection Guide
ControlLogix System
1756 Series Catalog Numbers
ControlLogix System
Logix Controllers Comparison
Characteristic
ControlLogix®
1756-L81E, 1756-L82E,
1756-L83E, 1756-L84E,
1756-L85E
ControlLogix
1756-L71, 1756-L72, 1756-L73,
1756-L73XT, 1756-L74, 1756-L75
GuardLogix®
1756-L71S, 1756-L72S, 1756-L73S
Armor™ ControlLogix
1756-L72EROM
Armor™ GuardLogix®
1756-L72EROMS
CompactLogix™
1769-L30ER,
1769-L30ER-NSE,
1769-L30ERM, 1769-L33ER,
1769-L33ERM, 1769-L36ERM
CompactLogix
1769-L24ER-BB1B,
1769-L24ER-QBFC1B,
1769-L27ERM-QBFC1B
CompactLogix
1769-L16ER-BB1B,
1769-L18ER-BB1B,
1769-L18ERM-BB1B,
1769-L19ER-BB1B
Compact GuardLogix
1769-L30ERMS,
1769-L33ERMS,
1769-L36ERMS
Controller tasks:
• Continuous
• Periodic
• Event
• 32
• 1000 programs/task
• 32
• 100 programs/task (with V23
and earlier)
• 1000 programs/task (with V24
and later)
• 32
• 100 programs/task (with V23
and earlier)
• 1000 programs/task (with
V24 and later)
• 32
• 100 programs/task
• 32
• 100 programs/task
• 32
• 100 programs/
task
Event tasks
Consumed tag, EVENT
instruction triggers,
Module Input Data
changes, and motion
events
Consumed tag, EVENT instruction
triggers, Module Input Data
changes, and motion events
Consumed tag, EVENT instruction
triggers, Module Input Data
changes, and motion events
Consumed tag, EVENT
instruction triggers and motion
events
Consumed tag, EVENT
instruction triggers and
motion events
Consumed tag,
EVENT instruction
triggers and motion
events
User memory
•
•
•
•
•
•
•
•
•
•
•
1756-L71: 2 MB
1756-L72: 4 MB
1756-L73, 1756-L73XT: 8 MB
1756-L74: 16 MB
1756-L75: 32 MB
1756-L71S: 2 MB + 1 MB
safety
• 1756-L72S: 4 MB +2 MB safety
• 1756-L73S: 8 MB +4 MB safety
• 1756-L72EROM: 4 MB
• 1756-L72EROMS: 4 MB +
2 MB safety
• 1769-L30ER,
1769-L30ER-NSE,
1769-L30ERM: 1 MB
• 1769-L33ER,
1769-L33ERM: 2 MB
• 1769-L36ERM: 3 MB
• 1769-L30ERMS: 1 MB +
0.5 MB safety
• 1769-L33ERMS: 2 MB +
1 MB safety
• 1769-L36ERMS: 3 MB +
1.5 MB safety
• 1769-L24ER: 750 KB
• 1769-L27ERM: 1 MB
• 1769-L16ER:
384 KB
• 1769-L18ER,
1769-L18ERM:
512 KB
• 1769L19ER-BB1B:
1 MB
Built-in ports
• Single-port
EtherNet/IP™
• 1 port USB client
1 port USB Client
• Dual-port EtherNet/IP
• 1 port USB client
• Dual-port EtherNet/IP
• 1 port USB Client
• Dual-port
EtherNet/IP
• 1 port USB Client
• Dual-port
EtherNet/IP
• 1 port USB Client
Communication
options
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• EtherNet/IP
• EtherNet/IP
– Embedded switch
– Single IP address
• DeviceNet
• USB Client
•
EtherNet/IP
– Embedded
switch
– Single IP address
• DeviceNet
• USB Client
• EtherNet/IP
– Embedded
switch
– Single IP
address
• USB Client
Controller connections
N/A
500 connections
500 connections
256 connections
256 connections
256 connections
Network nodes
•
•
•
•
•
N/A
N/A
N/A
N/A
N/A
Controller redundancy
Future
Full support
None
Backup via DeviceNet
Backup via DeviceNet
None
Integrated motion
EtherNet/IP
• EtherNet/IP
• SERCOS
• Analog
EtherNet/IP
EtherNet/IP
EtherNet/IP
EtherNet/IP
Conformal coating
Standard(1)
Standard(1)
Standard(1)
Custom(2)
Custom(2)
Custom(2)
1756-L81E: 3 MB
1756-L82E: 5 MB
1756-L83E: 10 MB
1756-L84E: 20 MB
1756-L85E: 40 MB
EtherNet/IP
ControlNet™
DeviceNet™
Data Highway Plus™
Remote I/O
SynchLink ™
USB Client
1756-L81E,: 60
1756-L82E: 80
1756-L83E: 100
1756-L84E: 150
1756-L85E: 300
EtherNet/IP
ControlNet
DeviceNet
Data Highway Plus
Remote I/O
SynchLink
USB Client
(1) Available when you select the K version of the controller.
(2) Contact the Rockwell Automation specialty products group for availability.
2
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Step 1
ControlLogix I/O Modules
Select:
• I/O modules—Some modules have field-side diagnostics, electronic fusing, or
individually isolated inputs/outputs
• A remote terminal block (RTB) or wiring system for each I/O module
Page 10
Step 2
ControlLogix Integrated Motion
Select:
• An EtherNet/IP communication module for Integrated Motion
• Associated cables
• Select drives, motors, and accessories (use the Motion Analyzer software)
Page 18
Step 3
ControlLogix Communication Modules
Select:
• Networks
• Communication modules
• Associated cables and network equipment
• Sufficient modules and cables if you are planning a redundant system
Page 19
Step 4
ControlLogix Controllers
Page 24
Step 5
ControlLogix Chassis
Select a controller:
• Standard ControlLogix controller
• Redundant ControlLogix controller
• Safety GuardLogix controller
• Extreme environment ControlLogix controller
• Standard Armor ControlLogix controller
• Safety Armor GuardLogix controller
Select:
• A chassis with sufficient slots
• Slot fillers for empty slots
Page 30
Step 6
ControlLogix Power Supplies
Select:
• One power supply for each chassis, if you are using standard power supplies
• A power supply bundle if you are planning a redundant power supply system
Page 31
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
3
Select a ControlLogix System
ControlLogix System Overview
The ControlLogix system provides discrete, drives, motion, process, and safety control together with communication and
state-of-the-art I/O in a small, cost-competitive package. The system is modular, so you can design, build, and modify it
efficiently with significant savings in training and engineering.
Example Configuration—ControlLogix System
A simple ControlLogix system consists of a standalone controller and I/O modules in one chassis. For a more comprehensive
system, use the following:
• Multiple controllers in one chassis
• Multiple controllers joined across networks
• I/O in multiple platforms that are distributed in many locations and connected over multiple I/O links
PowerMonitor™ 5000
Stratix 5700™
PanelView™ Plus 7
Stratix 5700
1715 I/O
ControlLogix
ControlLogix
1794 FLEX™ I/O
Dynamix™ 1444
PowerFlex® 755
4
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Conformal Coating
A conformal coating solution is offered on select ControlLogix products. Conformal coating helps protect the assembly by
providing a layer of protection against contaminants and humidity to extend product life in harsh, corrosive environments.
Conformally coated products have a ‘K’ suffix at the end of the catalog number, such as 1756-A4K. Conformally coated, AllenBradley® products meet or exceed these requirements:
• ANSI/ISA 71.04.2013 G3 Environment (10-year exposure)
• IEC 61086-3-1 Class 2
• IPC-CC-830
• MIL-I-46058C
• EN600068-2-52 salt mist test, severity level 3
The most current list of conformally coated products can be found by contacting your local Rockwell Automation distributor,
sales office, or at the following location:
http://www.ab.com/en/epub/catalogs/12762/2181376/2416247/360807/ControlLogix-System.html
ControlLogix-XT System
ControlLogix-XT™ (Extended Temperature) controllers function the same way as traditional ControlLogix controllers with an
extended temperature range. The ControlLogix-XT products include control and communication system components that
are conformally coated to extend product life in harsh, corrosive environments:
• The standard ControlLogix system can withstand temperature ranges from 0…60 °C (33…140 °F).
• When used independently, the ControlLogix-XT system can withstand temperature ranges from -25…70 C
(-13…158 F).
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
5
Select a ControlLogix System
Example Configuration—Redundant ControlLogix System
The 1756-L7 ControlLogix controller supports controller redundancy.
Workstation
EtherNet/IP
Switch
1715 Redundant I/O
6
1756 ControlLogix I/O
1734 POINT I/O™
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
PowerFlex 755 Drive
1756-EN2T
1756-EN2T
1756-EN2T
1756-EN2TR
1756-EN2TR
1756-RM2
1734-I/O
1734-AENTR
1756-OB16D
1756-IB16ISOE
1756-IB16ISOE
1756-L75
1756-EN2T
1756-EN2T
1756-EN2T
1756-EN2TR
1756-EN2TR
1756-EN2TR
1715-I/O
1715-I/O
1715-I/O
1715-I/O
1715-AENTR
1715-AENTR
1756-L75
1756-RM2
Redundant Chassis Pair
Select a ControlLogix System
Example Configuration—Redundant I/O System
The 1715 redundant I/O system lets a 1756-L7 ControlLogix controller communicate to a remote, redundant I/O chassis over
an EtherNet/IP network. The 1715 redundant I/O system provides fault tolerance and redundancy for critical processes by
using a redundant adapter pair and redundant I/O module pairs.
The redundant I/O system must be connected to a 1756-L7 ControlLogix system via an EtherNet/IP network. All connections
are established via the Ethernet network by using the topologies that the 1756-EN2TR communication bridge supports.
TERMINAL IDENTITY
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
AOTA
Dual.
AOTA
Dual.
1715-I/O
AOTA
Dual.
1715-I/O
1715-I/O
TERMINAL IDENTITY
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
AOTA
Dual.
1715-I/O
TERMINAL IDENTITY
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
AOTA
Dual.
IO BASE
1715-A310
1715-I/O
1715-AENTR
1715-AENTR
TERMINAL IDENTITY
CH1 CH1 CH1 CH1
CH1 CH1 CH1 CH1
IO BASE
1715-A310
TERMINAL IDENTITY
CH1 CH1 CH1 CH1
1715-I/O
TERMINAL IDENTITY
AOTA
Dual.
1756-RM2
1756-EN2TR
1756-L7 ControlLogix Secondary Chassis
1756-RM2
1756-EN2TR
1756-L7 ControlLogix Primary Chassis
1715 Redundant I/O System
For detailed specifications, see the 1715 Redundant I/O System Specifications Technical Data, publication 1715-TD001.
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
7
Select a ControlLogix System
GuardLogix Safety System
A GuardLogix controller is a ControlLogix controller that also provides safety control. The GuardLogix system is a dual
controller solution—you must use a GuardLogix controller with the appropriate safety partner to achieve SIL 3/PLe/Cat. 4. A
major benefit of this system is that it is still one project, safety, and standard together. The safety partner controller is a part of
the system, is automatically configured, and requires no user setup.
Application
Description
Up to and including SIL 3
The GuardLogix controller system is type-approved and certified for use in safety applications up to and including SIL 3, according to IEC 61508, and
applications up to and including category (PLe/Cat. 4), according to ISO 13849-1.
For more information, see the following:
• GuardLogix 5570 Controllers User Manual, publication 1756-UM022, provides information on how to install, configure, and operate GuardLogix
5570 controllers in the Studio 5000 Automation Engineering & Design Environment™ projects, version 21 or later.
• GuardLogix 5570 Controller System Safety Reference Manual, publication 1756-RM099, provides information on how to meet safety application
requirements for GuardLogix 5570 controllers in Studio 5000® projects, version 21 or later.
• GuardLogix Controllers User Manual, publication 1756-UM020, provides information on how to install, configure, and operate GuardLogix 5560
and GuardLogix 5570 controllers in RSLogix 5000® projects, version 20 or earlier.
• GuardLogix Controller Systems Safety Reference Manual, publication 1756-RM093, provides information on how to meet safety application
requirements for GuardLogix 5560 and GuardLogix 5570 controllers in RSLogix 5000 projects, version 20 or earlier.
• GuardLogix Safety Application Instruction Set Safety Reference Manual, publication 1756-RM095, provides programmers with details about the
GuardLogix safety application instruction set.
SIL 2
Components of the ControlLogix system are type-approved and certified for use in SIL 2 applications, according to IEC 61508.
For a list of ControlLogix system components that meet SIL 2 requirements, see the Using ControlLogix in SIL 2 Applications Safety Reference Manual,
publication 1756-RM001.
Stratix 5100™
PowerMonitor 1000
RS-485
TM
conformance tested
RS-485
RX
+
ACT
PanelView Plus 7
-
TX
STATUS
Mod
GuardLogix
Powermonitor 1000
Net
SHLD
LNK
Stratix 5700
1734 POINT Guard I/O™
PowerFlex 525
8
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Armor ControlLogix and Armor GuardLogix Systems
On-Machine™ standard and safety controllers support the same temperature range of ControlLogix, while offering global
certifications and ratings and Ingress Protection (IP67) for dust and wash-down protection for immersion between
15 cm…1 m (5.91…393.70 in.) in harsher environments.
ArmorStratix™ 5700
Armor ControlLogix
280E Networked ArmorStart®
1738-AENTR ArmorPOINT®
1732E ArmorBlock®
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
9
Select a ControlLogix System
ControlLogix I/O Modules
The ControlLogix architecture provides a wide range of input and output modules to span many applications, from highspeed digital to process control. The ControlLogix architecture uses a Producer/Consumer model so that input information
and output status can be shared among multiple controllers.
Each ControlLogix I/O module mounts in a ControlLogix chassis and requires a removable terminal block (RTB) or a 1492
interface module (IFM) to connect all field-side wiring. RTBs and IFMs are not included with the I/O modules. They must be
ordered separately.
For detailed specifications, see 1756 ControlLogix I/O Modules Specifications Technical Data, publication 1756-TD002.
AC Digital Input Modules
Cat. No.
Inputs/Outputs
Voltage Category
Operating Voltage Range
Removable Terminal Block
1756-IA8D
8 diagnostic inputs
(4 points/group)
120V AC
79…132V AC
1756-TBNH
1756-TBSH
1756-IA16
16 inputs
(8 points/group)
120V AC
74…132V AC
1756-TBNH
1756-TBSH
1756-IA16I
16 individually isolated inputs
120V AC
74…132V AC
1756-TBCH
1756-TBS6H
1756-IA32
32 inputs
(16 points/group)
120V AC
74…132V AC
1756-TBCH
1756-TBS6H
1756-IM16I
16 individually isolated inputs
240V AC
159…265V AC
1756-TBCH
1756-TBS6H
1756-IN16
16 inputs
(8 points/group)
24V AC
10…30V AC
1756-TBNH
1756-TBSH
AC Digital Output Modules
Cat. No.
Inputs/Outputs
Voltage Category
Operating Voltage Range
Removable Terminal Block
1756-OA8
8 outputs
(4 points/group)
120/240V AC
79…265V AC
1756-TBNH
1756-TBSH
1756-OA8D
8 diagnostic, electronically fused
outputs
(4 points/group)
120V AC
74…132V AC
1756-TBNH
1756-TBSH
1756-OA8E
8 electronically fused outputs
(4 points/group)
120V AC
74…132V AC
1756-TBNH
1756-TBSH
1756-OA16
16 mechanically fused/group outputs
(8 points/group)
120/240V AC
74…265V AC
1756-TBNH
1756-TBSH
1756-OA16I
16 individually isolated outputs
120/240V AC
74…265V AC
1756-TBCH
1756-TBS6H
1756-ON8
8 outputs
(4 points/group)
24V AC
10…30V AC, current > 50 mA
16…30V AC, current < 50 mA
1756-TBNH
1756-TBSH
10
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
DC Digital Input Modules
Cat. No.
Inputs/Outputs
Voltage Category
Operating Voltage Range
Removable Terminal Block
1756-IB16
16 inputs
(8 points/group)
12/24V DC sink
10…31.2V DC
1756-TBNH
1756-TBSH
1756-IB16D
16 diagnostic inputs
(4 points/group)
12/24V DC sink
10…30V DC
1756-TBCH
1756-TBS6H
1756-IB16I
16 individually isolated inputs
12/24V DC sink/source
10…30V DC
1756-TBCH
1756-TBS6H
1756-IB16IF
16 high-speed, individually isolated
inputs
12/24V DC sink/source
10…30V DC
1756-TBCH
1756-TBS6H
1756-IB16ISOE
16 individually isolated, sequence of
events inputs
24/48V DC sink/source
10…55V DC
1756-TBCH
1756-TBS6H
1756-IB32
32 inputs
(16 points/group)
12/24V DC sink
10…31.2V DC
1756-TBCH
1756-TBS6H
1756-IC16
16 inputs
(8 points/group)
48V DC sink
30…55V DC @ 60 °C (140 °F)
30…60V DC @ 55 °C (131 °F)
1756-TBNH
1756-TBSH
1756-IG16
16 inputs
(8 points/group)
5V DC TTL source (Low = True)
4.5…5.5V DC
1756-TBNH
1756-TBSH
1756-IH16I
16 individually isolated inputs
125V DC sink/source
90…146V DC
1756-TBCH
1756-TBS6H
1756-IH16ISOE
16 individually isolated, sequence of
events inputs
125V DC sink/source
90…140V DC
1756-TBCH
1756-TBS6H
1756-IV16
16 inputs
(8 points/group)
12/24V DC source
10…30V DC
1756-TBNH
1756-TBSH
1756-IV32
32 inputs
(16 points/group)
12/24V DC source
10…30V DC
1756-TBCH
1756-TBS6H
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
11
Select a ControlLogix System
DC Digital Output Modules
Cat. No.
Inputs/Outputs
Voltage Category
Operating Voltage Range
Removable Terminal Block
1756-OB8
8 outputs
12/24V DC source
10…30V DC
1756-TBNH
1756-TBSH
1756-OB8EI
8 electronically fused, individually
isolated outputs
12/24V DC source
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB8I
8 individually isolated outputs
12/24V DC source
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB16D
16 diagnostic outputs
(8 points/group)
24V DC source
19.2…30V DC
1756-TBCH
1756-TBS6H
1756-OB16E
16 electronically fused outputs
(8 points/group)
12/24V DC source
10…31.2V DC
1756-TBNH
1756-TBSH
1756-OB16I
16 individually isolated outputs
12/24V DC sink/source
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB16IEF
16 high-speed, individually isolated, 24V DC sink/source
electronically-fused outputs
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB16IEFS
16 scheduled, high-speed,
individually isolated,
electronically-fused outputs
24V DC sink/source
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB16IS
16 individually isolated outputs
8 scheduled outputs
12/24V DC sink/source
10…30V DC
1756-TBCH
1756-TBS6H
1756-OB32
32 outputs
(16 points/group)
12/24V DC source
10…31.2V DC
1756-TBCH
1756-TBS6H
1756-OC8
8 outputs
(4 points/group)
48V DC source
30…60V DC
1756-TBNH
1756-TBSH
1756-OG16
16 (8 points/group)
5V DC TTL source (Low=True)
4.5…5.5V DC
1756-TBNH
1756-TBSH
1756-OH8I
8 individually isolated outputs
120V DC
90…146V DC
1756-TBCH
1756-TBS6H
1756-OV16E
16 electronically fused outputs
(8 points/group)
12/24V DC sink
10…30V DC
1756-TBNH
1756-TBSH
1756-OV32E
32 electronically fused outputs
(16 points/group)
12/24V DC sink
10…30V DC
1756-TBCH
1756-TBS6H
Contact Output Modules
Cat. No.
Inputs/Outputs
Operating Voltage Range
Removable Terminal Block
1756-OW16I
16 normally open, individually isolated
outputs
5…125V DC
10…240V AC
1756-TBCH
1756-TBS6H
1756-OX8I
8 normally open
8 normally closed, individually isolated
outputs
(2 points/group)
5…125 DC
10…240V AC
1756-TBCH
1756-TBS6H
12
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Analog Input Modules
Cat. No.
Inputs/Outputs
Range
Resolution
Removable Terminal Block
1756-IF6CIS
6 individually isolated inputs, current sourcing
0…20 mA (over-range
indication when exceeded)
16 bits
0.34 A/bit
1756-TBNH
1756-TBSH
1756-IF6I
6 individually isolated inputs
±10.5V
0…10.5V
0…5.25V
0…21 mA
16 bits
10.5V: 343 V/bit
0…10.5V: 171 V/bit
0…5.25V: 86 V/bit
0…21 mA: 0.34 A/bit
1756-TBNH
1756-TBSH
1756-IF8
8 single-ended inputs
4 differential inputs
2 high-speed differential inputs
±10V
0…10V
0…5V
0…20 mA
±10.25V: 320 V/cnt (15 bits plus sign
bipolar)
0…10.25V: 160 V/cnt (16 bits)
0…5.125V: 80 V/cnt (16 bits)
0…20.5 mA: 0.32 A/cnt (16 bits)
1756-TBCH
1756-TBS6H
1756-IF8H
8 differential voltage or current inputs,
HART interface
±10V
0…5V
1…5V
0…10V
0…20 mA
4…20 mA
16…21 bits
1756-TBCH
1756-TBS6H
1756-IF8I
8 individually isolated inputs, current or voltage ±10V
0…10V
0…5V
0…20 mA
24 bits
±10.5V (1.49 V/count)
0…10.5V (1.49 V/count)
0…5.25V (1.49 V/count)
0…21 mA (2.99 nA/count)
1756-TBCH
1756-TBS6H
1756-IF8IH
8 individually isolated current inputs
0…20 mA
4…20 mA
16…21 bits
1756-TBCH
1756-TBS6H
1756-IF16
16 single-ended inputs
8 differential or 4 differential (high speed)
inputs
±10V
0…10V
0…5V
0…20 mA
16 bits
10.5V: 343 V/bit
0…10.5V: 171 V/bit
0…5.25V: 86 V/bit
0…21 mA: 0.34 A/bit
1756-TBCH
1756-TBS6H
1756-IF16H
16 differential current inputs, HART interface
0…20 mA
4…20 mA
16…21 bits
1756-TBCH
1756-TBS6H
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
13
Select a ControlLogix System
Analog RTD and Thermocouple Modules
Cat. No.
Inputs/Outputs
Range
Resolution
Removable Terminal Block
1756-IR6I
6 individually isolated RTD inputs
1…487 
2…1000 
4…2000
8…4000 
16 bits
1…487 : 7.7 m/bit
2…1000 : 15 m/bit
4…2000 : 30 m/bit
8…4020 : 60 m/bit
1756-TBNH
1756-TBSH
1756-IRT8I
8 individually isolated inputs, RTD or
thermocouple inputs (2 CJC)
1…500 
2…1000 
4…2000 
8…4000 
-100…100 mV
24 bits
0…5100.06 m/count
0…10200.12 m/count
0…20400.25 m/count
0…40800.50 m/count
-101…101 mV: 0.01 V/count
1756-TBCH
1756-TBS6H
1756-IR12
12 channels RTD mode
1…500 
2…1000 
4…2000 
8…4000 
24 bits
0…5100.06 m/count
0…10200.12 m/count
0…20400.25 m/count
0…40800.50 m/count
1756-TBCH
1756-TBS6H
1756-IT16
16 channels, thermocouple mode
2 CJC
-100…100 mV
24 bits
-101…101 mV: 0.01 V/count
1756-TBCH
1756-TBS6H
1756-IT6I
6 individually isolated thermocouple inputs
1 CJC
-12…78 mV
-12…30 mV
16 bits
-12…78 mV: 1.4 V/bit
-12…30 mV: 0.7 V/bit
1756-TBNH
1756-TBSH
1756-IT6I2
6 individually isolated thermocouple inputs
2 CJC
-12…78 mV (1.4 V per bit) 16 bits
-12…30 mV (0.7 V per bit) -12…78 mV: 1.4 V/bit
-12…30 mV: 0.7 V/bit
1756-TBNH
1756-TBSH
Analog Output Modules
Cat. No.
Inputs/Outputs
Range
Resolution
Removable Terminal Block
1756-OF4
4 voltage or current outputs
±10V
0…20 mA
Voltage:
15 bits across 10.5V, 320 V/bit
Current:
15 bits across 21 mA, 650 nA/bit
1756-TBNH
1756-TBSH
1756-OF6CI
6 individually isolated outputs, current
0…21 mA
13 bits across 21 mA (2.7 A)
1756-TBNH
1756-TBSH
1756-OF6VI
6 individually isolated outputs, voltage
±10.5V
14 bits across 21V (1.3 mV)
(13 bits across 10.5V +sign bit)
1756-TBNH
1756-TBSH
1756-OF8
8 voltage or current outputs
±10V
0…20 mA
15 bits across 21 mA - 650 nA/bit
15 bits across 10.4V - 320 V/bit
1756-TBNH
1756-TBSH
1756-OF8H
8 voltage or current outputs, HART interface
±10V
0…20 mA
4…20 mA
15…16 bits
1756-TBNH
1756-TBSH
1756-OF8I
8 individually isolated outputs, current or
voltage
±10V
0…10V
0…5V
0…20 mA
16 bit
±10.5V (0.32 mV/count)
0…10.5V (0.16 mV/count)
0…5.25V (0.08 mV/count)
0…21 mA (0.32 μA/count)
1756-TBCH
1756-TBS6H
1756-OF8IH
8 individually isolated current outputs
0…20 mA
4…20 mA
15 bits across 24 mA, 732 nA per bit
1756-TBCH
1756-TBS6H
14
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Analog Combination Input and Output Module
Cat. No.
Inputs/Outputs
Range
Resolution
Removable Terminal Block
1756-IF4FXOF2F
4 high-speed, submillisecond, differential inputs
2 high-speed voltage or current outputs
Input:
±10V
0…10V
0…5V
0…20 mA
Output:
±10V
0…20 mA
Input:
Approx 14 bits across ±10V DC (21V total)
±10V: 1.3 mV/bit, 14-bit effective
0…10.5V: 1.3 mV/bit, 13-bit effective
0…5.25V: 1.3 mV/bit, 12-bit effective
Approx 12 bits across 21 mA
0…21 mA: 5.25 A/bit
Output:
13 bits across 21 mA = 2.8 A/bit
14 bits across 21.8V = 1.3 mV/bit
1756-TBCH
1756-TBS6H
Specialty I/O Modules
Cat. No.
Inputs/Outputs
Description
Removable Terminal Block
1756-CFM
4 inputs (2 per channel)
2 outputs, current sourcing
Configurable flowmeter module
2 Flowmeter (F) inputs used for all modes
2 Gate inputs used in Totalizer mode for prover/store count
1756-TBNH
1756-TBSH
1756-HSC
2 counters, each with 3 inputs (A, B, Z for gate/reset) High-speed counter module
4 outputs (2 points/group)
5V operation: 4.5…5.5V DC
12/24V operation: 10…26.4V DC
1756-TBCH
1756-TBS6H
1756-LSC8XIB8I
8…24V DC counters
8 individually isolated, standard inputs, or counters
1756-TBCH
1756-TBS6H
1756-PLS
Left section: 2 groups of 4 outputs and 4 inputs each Programmable limit switch module
Center section: resolver interface and I/O control
Right section: 2 groups of 4 outputs and 4 inputs
each
Low speed counter module
8…40 kHz 24V DC counters
8 individually isolated 12/24V DC low speed (max frequency
40 kHz) counters
8 individually isolated high-speed 12/24V DC sink/source
standard or counter control inputs
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Requires 3 RTBs: 1756-TBNH or
1756-TBSH
15
Select a ControlLogix System
HART Smart Instrumentation
HART (Highway Addressable Remote Transducer) is an open protocol that is designed to connect analog devices. For HART
connectivity, select products available from Rockwell Automation and our Encompass™ Partner.
Typical HART Configuration
• ControlLogix
• 1756-IF8H or
• 1756-OF8H
HART Devices
HART Interfaces
If your application has
Select
Description
Analog and HART connectivity in one module
No external hardware is required to access HART signal
HART commands can be transmitted as unscheduled messages
Supports asset management software to HART device
1756-IF8H
1756-IF16H
1756-OF8H
Rockwell Automation® analog I/O modules
Analog and HART connectivity in one module
No external hardware is required to access HART signal
HART commands can be transmitted as unscheduled messages
Supports asset management software to HART device
Provides current isolation
1756-IF8IH
1756-OF8IH
Rockwell Automation isolated analog I/O modules
Data acquisition or control application with slow update requirements (such as a tank farm)
No external hardware is required to access HART signal
Does not connect directly to asset management software
MVI56-HART
ProSoft interface
Analog and HART in one module
Instrumentation in hazardous locations (FLEX Ex™ modules)
HART commands can be transmitted as unscheduled messages
Directly connects asset management software to HART devices
1794 FLEX I/O
1797 FLEX Ex I/O
There are FLEX I/O and FLEX Ex modules that are designed for
HART systems. These catalog numbers end in an H, such as
1797-IE8H.
16
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Accessories—I/O Modules
1756 Removable Terminal Blocks
Removable terminal blocks (RTBs) provide a flexible interconnection between your plant wiring and
1756 I/O modules. The RTB plugs into the front of the I/O module. The type of module determines
the RTB you need. You can choose screw-clamp or spring-clamp RTBs.
RTBs are not shipped with I/O modules. You must order them separately. The standard housing on
the front of the wiring arm is not necessarily deep enough for 2.5 mm2 (14 AWG) wiring. If you plan
to use 2.5 mm2 (14 AWG) wiring, also order the extended housing. For more information on
Extended-Depth Housing, see Rockwell Automation Knowledgebase article #41488, Use of the
1756-TBE Extended Terminal Housing. You can access the article at: https://rockwellautomation.custhelp.com/ (login is
required).
Attribute
1756-TBNH
1756-TBSH
1756-TBCH
1756-TBS6H
1756-TBE
Description
20-position NEMA
screw-clamp removable
block
20-pin spring-clamp
removable terminal block
with standard housing
36-pin cage-clamp
removable terminal block
with standard housing
36-pin spring-clamp
removable terminal block
with standard housing
Extended-depth terminal
block housing
Screw torque
0.8…1 N•m
7…9 lb•in
0.4 N•m
4.4 lb•in
—
Wiring Systems
As an alternative to buying RTBs and connecting the wires yourself, you can buy a wiring system of
the following:
• Interface modules (IFMs) that provide the I/O terminal blocks for Digital I/O modules. Use
the prewired cables that match the I/O module to the IFM.
• Analog interface modules (AIFMs) that provide the I/O terminal blocks for analog I/O
modules. Use the prewired cables that match the I/O module to the AIFM.
• I/O module-ready cables. One end of the cable assembly is an RTB that plugs into the front
of the I/O module. The other end has individually color-coded conductors that connect to a
standard terminal block.
I/O Module
RTB
Prewired Cable
Interface Module (IFM)
Factory-wired
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Field Wiring
17
Select a ControlLogix System
ControlLogix Integrated Motion
The Logix architecture supports motion control components that work in a wide variety of machine architectures:
• Integrated Motion on the EtherNet/IP network supports a connection to Ethernet drives.
• The Kinetix® integrated-motion solution uses a SERCOS or EtherNet/IP interface to perform multi-axis,
synchronized motion.
• Logix integrated motion supports the analog family of servo modules for controlling drives/actuators.
• Networked motion provides connection via the DeviceNet network to one axis drive to perform point-to-point
indexing.
For detailed specifications on motion interface modules, see the 1756 ControlLogix Integrated Motion Modules
Specifications Technical Data, publication 1756-TD004.
For more information, see these publications:
• Motion Analyzer CD to size your motion application and to make final component selection
Download the software from https://motionanalyzer.rockwellautomation.com/
• Kinetix Motion Control Selection Guide, publication GMC-SG001, to verify drive, motor, and accessory specifications
Integrated Motion on an EtherNet/IP Network
Product
Consideration
Drive that supports EtherNet/IP connections
Unlimited velocity, torque, and VHz configured drives:
• Kinetix 6500 drives
• Kinetix 5700 drives
• Kinetix 5500 drives
• Kinetix 350 drives
• PowerFlex 755 drives
• PowerFlex 527 drives
ControlLogix controller
• 1756-L7: as many as 100 drives per controller
• 1756-L8: as many as 256 drives per controller
ControlLogix EtherNet/IP communication module
• 1…8 position loop axes that are configured with the 1756-EN2T or 1756-EN2TR modules
• 1…128 position loop axes that are configured with the 1756-EN3TR module
ControlLogix L8 Controller
Logix5585E
Logix5585E
SAFETY ON
SAFETY ON
NET
NET
LINK
LINK
LNK1 LNK2 NET
RUN
REM
PROG
RUN
REM
OK
PROG
1
PanelView Plus 7
2
1 Gb
100 Mb
1 Gb
100 Mb
Stratix 5400™
1
2
3
4
5
6
7
8
9 10 11 12 25 26
2
1
1
4
5
10/100/1000 PoE+
8
9
12
13
16
17
100/1000 SFP
20
21
24
IN
Disp.
Mode
IN
OUT
PoE
Out
PRP
GPS
DLR
2
1
Setup
3
4
Speed
EIP Net
Alarms PSU
Duplex
TimeCD
EIP Mod
13 14 15 16 17 18 19 20 21 22 23 24 27 28
OUT
GPS ANT.
DIG.TimeCode
25
100/1000 SFP+
TOD
ANA.TimeCode
Express
Setup
28
Console
Alarm
Stratix 5700
AUTO
At Reference
6 0 . 00 Hz
F
PowerFlex 755
480V
4.2A
20G . . . B4P2
00
ESC
REF
7
4
1
8
5
2
STS
ENET
LINK
PAR# TEXT
Mod
Net
Mod
Net
Mod
Net
5700
5700
5700
9
6
3
0
755
Kinetix 5700
CAUTION
HOT surfaces can cause severe burns
5069-IB16
5069-FPD
5069-ARM
PowerFlex 755
COMPACT I/O
5069-AEN2TR with Compact I/O™
18
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
ControlLogix Communication Modules
Separate communication modules are available for different networks. Install multiple communication modules into the
ControlLogix backplane to bridge or route control and information data between different networks. You can route a
message through a maximum of four chassis (eight communication hops). You do not need a ControlLogix controller in the
chassis.
Application
Network
Page
•
•
•
•
•
•
•
•
Plant management (material handling)
Configuration, data collection, and control on one high-speed network
Time-critical applications with no established schedule
Inclusion of commercial technologies (such as video over IP)
Internet/Intranet connection
High-speed transfer of time-critical data between controllers and I/O devices
Integrated Motion on the EtherNet/IP network and safety
Redundant controller systems
EtherNet/IP
19
•
•
•
•
•
High-speed transfer of time-critical data between controllers and I/O devices
Deterministic and repeatable data delivery
Media redundancy
Intrinsic safety
Redundant controller systems
ControlNet
20
•
•
•
•
Connections of low-level devices directly to plant floor controllers, without interfacing them through I/O modules
Data sent as needed
More diagnostics for improved data collection and fault detection
Less wiring and reduced start-up time than a traditional, hard-wired system
DeviceNet
20
• Plant-wide and cell-level data sharing with program maintenance
• Data sent regularly
• Transfer of information between controllers
Data Highway Plus
21
• Connections between controllers and I/O adapters
• Data sent regularly
• Distributed control so that each controller has its own I/O and communicates with a supervisory controller
Remote I/O
21
• Fieldbus transmitters and actuators
• Closed-loop control
• Process automation
Foundation Fieldbus
22
For detailed specifications, see the 1756 ControlLogix Communication Modules Specifications Technical Data,
publication 1756-TD003.
EtherNet/IP Communication Modules
EtherNet/IP (Ethernet Industrial Protocol) is an open industrial-networking standard that supports real time
I/O messaging and message exchange. The EtherNet/IP network uses off-the-shelf Ethernet communication chips and
physical media.
Cat. No.
Description
Media
Communication
Rate
Integrated Motion TCP/IP
on the EtherNet/IP Connections
Network Axes,
max
Logix
Connections
1756-EN2F
EtherNet/IP bridge, fiber
Fiber
100 Mbps
8
128
256
1756-EN2T
EtherNet/IP bridge, copper
Copper
10/100 Mbps
8
128
256
1756-EN2TR
EtherNet/IP bridge, embedded switch, copper
Dual copper
10/100 Mbps
8
128
256
1756-EN3TR
EtherNet/IP bridge, embedded switch, copper
Dual copper
10/100 Mbps
128
128
256
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
19
Select a ControlLogix System
Cat. No.
Description
Media
Communication
Rate
Integrated Motion TCP/IP
on the EtherNet/IP Connections
Network Axes,
max
Logix
Connections
1756-EN2TXT
ControlLogix-XT, extended temperature
EtherNet/IP bridge, copper for extreme environments
Copper
10/100 Mbps
8
128
256
1756-EN2TRXT
ControlLogix-XT, extended temperature
EtherNet/IP bridge, embedded switch, copper
Dual copper
10/100 Mbps
8
128
256
1756-EN2TSC
EtherNet/IP secure communication module
Copper
10/100 Mbps
—
128
256
1756-ENBT
EtherNet/IP bridge, copper
Copper
10/100 Mbps
—
64
128
1756-EWEB
Ethernet web server module
Copper
10/100 Mbps
—
64
128
ControlNet Communication Modules
The ControlNet network combines the functionality of an I/O network and a peer-to-peer network, providing high-speed
performance. The ControlNet network provides deterministic, repeatable transfers of critical control data.
Cat. No.
1756-CN2
1756-CN2R
1756-CNB
1756-CNBR
1756-CN2RXT
Description
ControlNet bridge, standard media
ControlNet bridge, redundant media
ControlNet bridge, standard media
ControlNet bridge, redundant media
ControlLogix-XT, extended temperature ControlNet bridge, redundant
media
Communication Rate
Logix Connections
Number of Nodes
5 Mbps
128(1)
99
5 Mbps
128(1)
99
5 Mbps
64(2)
99
5 Mbps
64(2)
99
5 Mbps
128(1)
99
(1) 128 connections are available for standard use. An extra three connections are reserved for redundant control.
(2) Recommend using only 40…48 Logix connections for I/O.
DeviceNet Communication Module
The DeviceNet network provides connections between simple, industrial devices (such as sensors and actuators) and
higher-level devices (such as controllers and computers).
Cat. No.
Description
Communication Rate
Number of Nodes
1756-DNB
DeviceNet bridge
125 Kbps (500 m max)
250 Kbps (250 m max)
500 Kbps (100 m max)
64
20
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Data Highway Plus and Remote I/O Communication Modules
The Data Highway Plus network supports messaging between devices. The remote I/O link connects to remote I/O chassis
and other intelligent devices.
The 1756-DHRIO module supports messaging between devices on DH+™ networks. The remote I/O functionality enables the
module to act as a scanner for transferring digital and block transfer data to and from remote I/O devices.
The 1756-RIO module can act as a scanner or adapter on a remote I/O network. The 1756-RIO transfers digital, block transfer,
analog, and speciality data without message instructions.
Cat. No.
Description
Communication Rate
DH+
Connections
RIO Connections
1756-DHRIO
Data Highway Plus/Remote I/O
two-channel communication module
57.6 Kbps, 115.2 Kbps, 230.4 Kbps
32 DH+ messages Remote I/O scanner only
per DH+ module 32 logical rack connections per remote
I/O channel
16 block transfer connections per remote
I/O channel
1756-RIO
Remote I/O communication module
57.6 Kbps, 115.2 Kbps, 230.4 Kbps
—
1756-DHRIOXT
ControlLogix-XT, extended
temperature Data Highway Plus/
Remote I/O two-channel
communication module
57.6 Kbps, 115.2 Kbps, 230.4 Kbps
32 DH+ messages Remote I/O scanner only
per DH+ module 32 logical rack connections per remote I/O
channel
16 block transfer connections per remote
I/O channel
Maximum
Recommended Logix
Connections
32
Remote I/O scanner or adapter
10 scheduled I/O
32 physical racks (0…76), any
combination of rack size and block transfers
32
Accessories: DH+ and Remote I/O Networks
Cat. No.
Description
Specifications
1770-CD
Cable to connect communication module to DH+ network
Belden 9463 twinaxial
9300-RADKIT
Remote access dial-in kit
56 Kbps modem connection to devices on a DH+ network
includes the following:
• Pre-configured modem
• Communication module
• DIN rail mounting hardware
• Associated cables
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
21
Select a ControlLogix System
FOUNDATION Fieldbus Linking Devices
The FOUNDATION Fieldbus protocol is a network that is designed for distributed control of process applications.
Cat. No.
Description
Communication Rate
Number of H1 Ports
Devices per H1 Link
Devices per Linking Device
1757-FFLD2
FOUNDATION Fieldbus bridge to an
Ethernet network
FOUNDATION Fieldbus: 31.25 Kbps
EtherNet/IP: 10/100 Mbps
2
16
(8…10 recommended)
32
FOUNDATION Fieldbus bridge to a
ControlNet network
FOUNDATION Fieldbus: 31.25 Kbps
ControlNet: 5 Mbps
2
16
(8…10 recommended)
32
1757-FFLD4
1757-FFLDC2
1757-FFLDC4
4
4
64
64
Example Configuration—Bridge to EtherNet/IP Network
• FactoryTalk® View SE
• RSFieldbus™
• Studio 5000 Environment
HSE/IP
1757-FFLD4
H1(1)
H1(2)
H1(3)
H1(4)
22
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Other Connectivity Options
Option
Consideration
USB connection
The ControlLogix controllers have a USB port in place of the serial port.(1) If your application requires RS-232 functionality, see the many Encompass
Partners’ products at http://www.rockwellautomation.com/encompass.
DH-485 network
The controller serial port is compatible with DH-485 communication. The DH-485 connection does support remote programming and monitoring via the
Logix Designer application.
Or, add a 1756-DH485 communication module.
SynchLink™ network
The SynchLink communication module (1756-SYNCH) provides time synchronization and data broadcasting capabilities for distributed motion and
coordinated drive control. The module connects a ControlLogix chassis to a SynchLink fiber-optic communication link.
(1) The USB port is intended only for temporary local programming purposes and not intended for permanent connection. Do not use the USB port in hazardous locations.
Modbus Support
To access a Modbus TCP network, use one of the following methods:
• Connect through the 1756-EN2T, 1756-EN2TR, 1756-EN2F, or 1756-EN3TR modules, with firmware revision 5.007 or
later and execute a ladder-logic routine.
• Connect through the 1756-EWEB module, with firmware revision 4.006 or later and execute a ladder-logic routine.
For more information, see Knowledgebase document 470365 at
http://www.rockwellautomation.com/knowledgebase/.
To access a Modbus RTU network, connect through the serial port (if available) and execute a ladder-logic routine. For more
information, see Using Logix5000™ Controllers as Masters or Slaves on Modbus Application Solution, publication CIG-AP129.
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
23
Select a ControlLogix System
ControlLogix Controllers
The ControlLogix controller provides a scalable controller solution capable of addressing many I/O points.
The controller can be placed into any slot of a ControlLogix chassis and multiple controllers can be installed in the same
chassis. Multiple controllers in the same chassis communicate with each other over the backplane (just as controllers can
communicate over networks) but operate independently.
ControlLogix controllers can monitor and control I/O across the ControlLogix backplane, and over I/O links. ControlLogix
controllers can communicate over EtherNet/IP, ControlNet, DeviceNet, DH+, Remote I/O, and RS-232-C (DF1/DH-485
protocol) networks and many third-party process and device networks. To provide communication for a ControlLogix
controller, install the appropriate communication interface module into the chassis.
Cat. No.
Description
User Memory
1756-L81E
ControlLogix controller, 1 built-in USB port(1), single port EtherNet/IP
3 MB
1756-L82E
5 MB
1756-L83E
10 MB
1756-L84E
20 MB
1756-L85E
1756-L71
40 MB
ControlLogix controller, 1 built-in USB port(1)
2 MB
1756-L72
4 MB
1756-L73
8 MB
1756-L74
16 MB
1756-L75
32 MB
1756-L73XT
ControlLogix-XT controller, extreme environment
8 MB
1756-L71S
GuardLogix safety controllers
2 MB standard
1 MB safety
1756-L72S
4 MB standard
2 MB safety
1756-L73S
8 MB standard
4 MB safety
1756-L7SP
GuardLogix safety partner (one is required for each GuardLogix L7 controller)
—
1756-L72EROM
Armor ControlLogix controllers, EtherNet/IP dual port
4 MB
1756-L72ERMOS
Armor GuardLogix controllers, EtherNet/IP dual port
4 MB standard
2 MB safety
(1) The USB port is intended only for temporary local programming purposes and not intended for permanent connection. Do not use the USB port in hazardous locations.
For detailed specifications, see the 1756 ControlLogix Controllers Technical Data, publication 1756-TD001.
24
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Standard ControlLogix Controllers
The ControlLogix controller is part of the Logix5000 family of controllers. A ControlLogix system
includes the following:
• The ControlLogix controller, available in different combinations of user memory
• Studio 5000 environment
• 1756 ControlLogix I/O modules that reside in a 1756 chassis
• Separate communication modules for network communication
Feature
1756-L71, 1756-L72, 1756-L73, 1756-L74, 1756-L75
1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E,
1756-L85E
Controller tasks
• 32 tasks
• 1000 programs/task(2)
• Event tasks: all event triggers
• 32 tasks
• 1000 programs/task
• Event tasks: all event triggers
Built-in communication ports
1 port USB Client
• 1 port USB client
• Single-port EtherNet/IP
Communication options
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Controller device
500 connections
N/A
Node capacity
N/A
•
•
•
•
•
Network connections, per network module(1)
•
•
•
•
•
•
N/A(4)
Controller redundancy
Full support
Future
Integrated motion
• EtherNet/IP connection
• SERCOS interface
• Analog options (encoder input, LDT input, SSI input)
• EtherNet/IP connection
Programming languages
•
•
•
•
•
•
•
•
EtherNet/IP
ControlNet
DeviceNet
Data Highway Plus
Remote I/O
SynchLink
Third-party process and device networks
256 EtherNet/IP; 128 TCP (1756-EN2x, 1756-ENxT(R))
128 EtherNet/IP; 64 TCP (1756-ENBT)
128 ControlNet (1756-CN2/B)
100 ControlNet (1756-CN2/A)
64 EtherNet/IP; 32 TCP (5069-AENTR)
40 ControlNet (1756-CNB)
Relay ladder
Structured text
Function block
Sequential function chart (SFC)
EtherNet/IP
ControlNet
DeviceNet
Data Highway Plus
Remote I/O
SynchLink
Third-party process and device networks
1756-L81E: 60 EtherNet/IP nodes(3)
1756-L82E: 80 EtherNet/IP nodes(3)
1756-L83E: 100 EtherNet/IP nodes(3)
1756-L84E: 150 EtherNet/IP nodes(3)
1756-L85E: 300 EtherNet/IP nodes(3)
Relay ladder
Structured text
Function block
Sequential function chart (SFC)
(1) For the ControlLogix 5580 controllers, the total number of devices cannot exceed the total number of devices that the controller supports. The number of connections per network module shown is the maximum
designed capacity of the modules. The device data size and requested data rate determines the actual device capacity.
(2) Studio 5000, version 23 and earlier, is limited to 100 Programs/Task.
(3) This value is the maximum number of EtherNet/IP nodes that the controller supports. Use the Integrated Architecture Builder design tool to lay out and validate your system design and additional node options. For
further information on nodes on an EtherNet/IP network, see the ControlLogix 5580 Controllers User Manual, publication 1756-UM543.
(4) This value is determined by the node capacity for the ControlLogix 5580 controllers.See the node capacity feature for more information.
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
25
Select a ControlLogix System
ControlLogix-XT Controllers
The ControlLogix-XT controllers function in the same way as the traditional ControlLogix controllers, with
an extended temperature range, and have the same features as the ControlLogix L7 controllers.
The ControlLogix-XT products include control and communication system components that are
conformally coated to extend product life in harsh, corrosive environments:
• While the standard ControlLogix system can withstand temperatures from 0…60 °C (33…140 °F),
the ControlLogix-XT system can withstand temperatures from -25…70 °C (-13…158 °F).
Redundant ControlLogix Controllers
The ControlLogix controller supports controller redundancy. In a redundant controller system, you need these components:
• Two 1756 chassis each with the following the same:
– Number of slots
– Modules in the same slots
– Redundancy firmware revisions in each module
– Two additional ControlNet nodes(1) outside the redundant chassis pair.
• One 1756-RM2 or 1756-RM2XT module per chassis that supports the following:
– One or two ControlLogix or ControlLogix-XT controllers of the same family
– As many as seven ControlNet or EtherNet/IP communication modules in any combination
• One or two 1756-RMCx cables
For additional redundancy rules and restrictions, see the ControlLogix Enhanced Redundancy System User Manual,
publication 1756-UM535.
(1) For a ControlNet I/O drop, two more ControlNet nodes are required outside the redundancy chassis pair. Not applicable with Ethernet I/O control.
26
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
GuardLogix Controllers
A GuardLogix controller is a ControlLogix controller that also provides safety
control.
Application
Description
SIL 1, 2, 3
The GuardLogix controller system is type-approved and certified for use in safety applications up to and including SIL 3 according to
IEC 61508, and applications up to and including PLe/Cat.4 according to ISO 13849-1. For more information, see the following:
• GuardLogix 5570 Controllers User Manual, publication 1756-UM022. Provides information on how to install, configure, and operate
GuardLogix 5570 Controllers in Studio 5000, Version 21 or later projects.
• GuardLogix 5570 Controller Systems Safety Reference Manual, publication 1756-RM099. Provides information on how to meet safety
application requirements for GuardLogix 5570 Controllers in Studio 5000, Version 21 or later projects.
The GuardLogix system is a dual controller solution. You must use a primary controller and a
safety partner to achieve SIL 3/PLe/Cat. 4.
Primary Controller
Safety Partner
1756-L71S, 1756-L72S, 1756-L73S
1756-L7SP
1756-L73SXT
1756-L7SPXT
During development, safety and standard have the same rules, multiple programmers, online
editing, and forcing are all allowed. Once the project is tested and ready for final validation, you set the Safety Task to a SIL 3
integrity level, which the GuardLogix controller enforces. When safety memory is locked and protected, the safety logic
cannot be modified and all safety functions operate with SIL 3 integrity. On the standard side of the GuardLogix controller, all
functions operate like a regular Logix controller.
Use Guard I/O™ modules for field device connectivity on Ethernet or DeviceNet networks, and for safety interlocking
between GuardLogix controllers use Ethernet or ControlNet networks. Multiple GuardLogix controllers can share safety data
for zone to zone interlocking, or one GuardLogix controller can use remote distributed safety I/O between different cells/
areas.
The GuardLogix controller has the standard features of a ControlLogix controller and these safety-related features.
Feature
1756-LSP, 1756-L71S, 1756-L72S, 1756-L73S, 1756-L7SP, 1756-L73SXT, 1756-L7SPXT
Safety communication options
Standard and safety
• EtherNet/IP
• ControlNet
• DeviceNet
Network connections, per network module
•
•
•
•
Controller redundancy
Not supported
Safety Task Programming languages
Relay ladder
256 EtherNet/IP; 128 TCP (1756-EN2x, 1756-EN3x)
128 EtherNet/IP; 64 TCP (1756-ENBT)
128 ControlNet (1756-CN2/B, 1756-CN2R/B)
64 DeviceNet (1756-DNB)
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
27
Select a ControlLogix System
Armor ControlLogix and Armor GuardLogix Controllers
The Armor ControlLogix controller, extends the standard ControlLogix platform to the On-Machine space. The Armor
GuardLogix controller delivers safety control up to SIL 3, PLe, CAT 4.
Both controllers have the equivalent of two embedded 1756-EN3TR modules, which offer dual independent Ethernet ports
that support a DLR network topology.
Feature
1756-L72EROM
1756-L72EROMS
Communication options
Standard
• EtherNet/IP
Standard and safety
• EtherNet/IP
Controller redundancy
Not supported
Programming languages
•
•
•
•
28
Relay ladder
Structured Text
Function block
Sequential function chart
• Relay ladder
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Accessories—Controllers
Memory Cards
Memory cards offer nonvolatile memory to store a user program and tag data on a controller. The ControlLogix L7 and
GuardLogix L7 controllers ship with 1784-SD1 Secure Digital (SD) card installed. The memory card installs in a socket on the
controller. Through the Logix Designer application, you can manually trigger the controller to save to or load from nonvolatile
memory or configure the controller to load from nonvolatile memory on powerup.
Attribute
1784-SD1
1784-SD2
Memory
1 GB
2 GB
Supported controllers
1756 ControlLogix L7 and 1756 GuardLogix L7
Weight, approx
1.76 g (0.062 oz)
1756 Energy Storage Modules
Important: Energy storage modules apply to only ControlLogix 5570 controllers.
Instead of a battery, the ControlLogix and GuardLogix controllers ship with a 1756-ESMCAP energy storage module (ESM)
installed.
Cat No.
Description
1756-ESMCAP
Capacitor-based ESM included with the controller.
1756-ESMNSE
ESM without WallClockTime back-up power. Additionally, you can use this ESM only with a 1756-L73 (8 MB) or smaller memory-sized controller.
Use this ESM if your application requires that the installed ESM deplete its residual energy to 40 μJ or less before transporting it into or out of your application.
1756-ESMNRM
ESM that secures the controller by permanently preventing the USB connection and SD card use.
This ESM provides your application an enhanced degree of security.
The ControlLogix-XT extreme temperature controller ships with a 1756-ESMNCAPXT energy storage module installed.
Cat No.
Description
1756-ESMCAPXT
Capacitor-based ESM included with the controller.
1756-ESMNSEXT
ESM without WallClockTime back-up power. Additionally, you can use this ESM only with a1756-L73XT (8 MB) or smaller memory-sized controller.
Use this ESM if your application requires that the installed ESM deplete its residual energy to 40 μJ or less before transporting it into or out of your application.
1756-ESMNRMXT
ESM that secures the controller by permanently preventing the USB connection and SD card use.
This ESM provides your application an enhanced degree of security.
The 1756-L7SP safety partner for a GuardLogix system has the following modules available.
Cat No.
Description
1756-SPESMNSE
Capacitor-based ESM for a GuardLogix safety partner.
1756-SPESMNRM
ESM for a GuardLogix safety partner that secures the safety partner by permanently preventing the USB connection and SD card use.
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
29
Select a ControlLogix System
ControlLogix Chassis
The ControlLogix system is a modular system that requires a 1756 I/O chassis. Place
any module into any slot. The backplane provides a high-speed communication
path between modules.
The chassis are designed for horizontal-only, back-panel mounting. The chassis are
available in these options:
• Standard chassis
• ControlLogix-XT chassis
For detailed specifications, see the 1756 ControlLogix Chassis Specifications Technical Data, publication 1756-TD006.
Standard Chassis
The chassis backplane provides a high-speed communication path between modules and distributes power to each of the
modules within the chassis.
Cat. No.
Description
Slots
1756-A4
Standard chassis
4
1756-A7
7
1756-A10
10
1756-A13
13
1756-A17
17
ControlLogix-XT Chassis
The ControlLogix-XT chassis support extreme temperature environments.
Cat. No.
Description
Slots
Temperature Range
1756-A7XT
ControlLogix-XT chassis
7
-25…70 °C (-13…158 °F)
Accessories - Chassis
Use a slot filler module to fill empty slots.
Cat. No.
Description
1756-N2
Slot filler module for empty slots in standard ControlLogix chassis
1756-N2XT
Slot filler module for empty slots in ControlLogix-XT chassis
30
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
ControlLogix Power Supplies
ControlLogix power supplies are used with the 1756 chassis to provide 1.2V, 3.3V, 5V, and 24V DC
power directly to the chassis backplane. Select from these configurations:
• Standard power supplies
• ControlLogix-XT power supplies
• Redundant power supplies
For detailed specifications, see the 1756 ControlLogix Power Supplies Specifications Technical
Data, publication 1756-TD005.
Standard Power Supplies
You mount a standard power supply directly on the left end of the chassis, where it plugs directly into the backplane.
Cat. No.
Description
Voltage Category
Operating Voltage Range
Chassis
1756-PA72
Standard AC power supply
120V/220V AC
85…265V AC
Standard, series A, and series B
120V/220V AC
85…265V AC
Standard, series B
24V DC
18…32V DC
Standard, series A, and series B
1756-PB75
24V DC
18…32V DC
Standard, series B
1756-PC75
48V DC
30…60V DC
Standard, series B
1756-PH75
125V DC
90…143V DC
Standard, series B
1756-PA75
1756-PB72
Standard DC power supply
ControlLogix-XT Power Supplies
The ControlLogix-XT power supplies support extreme temperature environments.
Cat. No.
Description
Voltage Category
Operating Voltage Range
Chassis
1756-PAXT
ControlLogix-XT AC power supply
85…265V AC
120/240V AC
XT
1756-PBXT
ControlLogix-XT DC power supply
24V DC
18…32V DC
XT
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
31
Select a ControlLogix System
Redundant Power Supplies
A redundant power supply system provides extra uptime protection for chassis that are used in critical applications. The
redundant power supplies funnel power through the chassis adapter to the ControlLogix series B chassis backplane. To build
a redundant power supply system, you need the following components.
Cat. No.
Amount
Description
Voltage Category
Operating Voltage Range
Chassis
1756-PAR2
Kit
Bundled system contains:
– Two1756-PA75R power supplies
– Two 1756-CPR2 cables
– One 1756-PSCA2 chassis adapter
110V AC
N/A
Standard, series B
1756-PAR2XT
Kit
Bundled system contains:
– Two1756-PAXTR power supplies
– Two 1756-CPR2 cables
– One 1756-PSCA2 chassis adapter
110V AC
N/A
1756-PBR2
Kit
Bundled system contains:
– Two 1756-PB75R power supples
– Two 1756-CPR2 cables
– One 1756-PSCA2 chassis adapter
24V DC
N/A
1756-PBR2XT
Kit
Bundled system contains:
– Two 1756-PBXTR power supples
– Two 1756-CPR2 cables
– One 1756-PSCA2 chassis adapter
24V DC
N/A
1756-PA75R/A or
1756-PAXTR
2
Redundant AC power supply
120V/220V AC
85…256V AC
1756-PB75R/A or
1756-PBXTR
2
Redundant DC power supply
24V DC
19.2…32V DC
N/A
2
Redundant power supply cable:
Connector angle = straight, length = 0.91 m (3 ft)
Connector angle = down, length = 0.91 m (3 ft)
Connector angle = up, length = 0.91 m (3 ft)
N/A
1756-CPR2 or
1756-CPR2D or
1756-CPR2U
1756-PSCA2 or
1756-PSCA2XT
1
Redundant power supply chassis adapter
N/A (user-supplied)
2
Annunciator wiring(1)
(Maximum length = 10 m [32.8 ft])
(1) Optional user-supplied annunciator wiring can be connected to the solid-state relay input for status and troubleshooting purposes.
32
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Select a ControlLogix System
Notes:
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
33
Select a ControlLogix System
Notes:
34
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
ControlLogix System Selection Guide
35
Rockwell Automation Publication 1756-SG001U-EN-P - February 2016
Rockwell Automation Support
Use the following resources to access support information.
Technical Support Center
Knowledgebase Articles, How-to Videos, FAQs, Chat, User
Forums, and Product Notification Updates.
www.rockwellautomation.com/knowledgebase
Local Technical Support Phone Numbers
Locate the phone number for your country.
www.rockwellautomation.com/global/support/get-supportnow.page
Direct Dial Codes
Find the Direct Dial Code for your product. Use the code to
route your call directly to a technical support engineer.
www.rockwellautomation.com/global/support/direct-dial.page
Literature Library
Installation Instructions, Manuals, Brochures, and
Technical Data.
www.rockwellautomation.com/literature
Product Compatibility and Download Center
(PCDC)
Get help determining how products interact, check
features and capabilities, and find associated firmware.
www.rockwellautomation.com/global/support/pcdc.page
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this
document, complete the How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/
documents/du/ra-du002_-en-e.pdf.
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainabilityethics/product-environmental-compliance.page.
Allen-Bradley, Armor, ArmorBlock, Armor GuardLogix, ArmorPOINT, ArmorStart, ArmorStratix, CompactLogix, ControlLogix, ControlLogix-XT, Data Highway Plus, DH+, Dynamix,
Encompass, FactoryTalk, FLEX Ex, FLEX I/O, Guard I/O, GuardLogix, Kinetix, LISTEN. THINK. SOLVE., Logix5000, On-Machine, PanelView, POINT Guard I/O, POINT I/O, PowerFlex,
PowerMonitor, Rockwell Automation, Rockwell Software, RSFieldbus, RSLogix 5000, Stratix 5100, Stratix 5400, Stratix 5700, Studio 5000, Studio 5000 Automation Engineering &
Design Environment, and SynchLink are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
ControlNet, DeviceNet, and EtherNet/IP are trademarks of the ODVA.
Publication 1756-SG001U-EN-P - February 2016
Supersedes Publication 1756-SG001T-EN-P - October 2015
Copyright © 2016 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project