SD-300SC DVD Video Player User`s Manual
Introduction
Connections
2
18
DIGITAL VIDEO
Basic playback
DVD VIDEO PLAYER
SD-300SC
OWNER’S MANUAL
Advanced playback
Function setup
Others
© 2004 Toshiba Corporation
26
34
60
72
Introduction
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The symbol for CLASS II (Double Insulation)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location see service procedure.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.
2
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.
These servicing instructions are for use by qualified service personnel only. To reduce the risk
of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
Introduction
CAUTION:
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video
player.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
Be aware that this equipment is still powered even after the ON/STANDBY indicator turns off (standby mode) by
pressing the ON/STANDBY button. To disconnect this equipment completely from the main power, pull out the
power plug from the wall outlet.
3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
4
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Introduction
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
5
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
15. When you use headphones, keep the volume at a moderate level. If you use the headphones continuously
with high volume sound, it may cause hearing damage.
16. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
17. The apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, should be placed on the apparatus.
6
18. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.
Introduction
19. Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal
injury and serious damage to the apparatus.
20. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and apparatus malfunction.
21. If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause
fire.
22. While it is thundering, do not touch the connecting cables or the apparatus.
23. The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance to
humans and the environment. When disposing of this apparatus, follow the rules and regulations in your
area.
7
Introduction
Precautions
Notes on handling
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory. Take care not to give
it a shock or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on moisture condensation
Moisture condensation damages the DVD video player.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
Moisture condensation occurs during the following
cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
To obtain a clear picture
The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment. For details, contact your
nearest dealer.
8
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.
Notes on Discs
Structure of disc contents
Do not touch the playback side of the disc.
Introduction
On handling discs
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Chapter 1
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Playback side
Do not attach paper or tape to discs.
VIDEO CD/audio CD
VIDEO CD/audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
DVD video discs are copy protected, and any
recordings made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
9
Introduction
Notes on Discs (continued)
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
” may appear on the TV screen during operation.
“
A “ ” means that the operation is not permitted by the
DVD video player or the disc.
Playable discs
This DVD video player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
DVD
video
discs
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find
or
, disc playback will not be allowed by the player.
(In this case, the DVD video player will display a
message on-screen.)
Approx. 160 minutes
(double sided disc)
VIDEO
CDs
DIGITAL VIDEO
Audio
+
video
(moving
pictures)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
On VIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
Audio
CDs
Audio
The following discs are also available.
DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA format
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or
non-standardized discs, etc., even if they may be
labeled as above.
• This DVD video player uses the NTSC color system,
and cannot play DVD video discs recorded in any
other color system (PAL, SECAM, etc.).
Because of problems and errors that can occur during
the creation of DVD software and/or the manufacture of
DVD discs, Toshiba America Consumer Products,
L.L.C., Toshiba Hawaii, Inc. and Toshiba of Canada, Ltd.
cannot guarantee that this player will play every feature
of every DVD bearing the DVD logo. As one of the
creators of DVD technology, Toshiba DVD players are
manufactured to the highest standards of quality and, as
a result, such incompatibilities are very rare. If you
happen to experience and difficulty playing a DVD on a
Toshiba DVD player, please feel free to call our Contact
listed in “How to Obtain Warranty Services” 74 .
10
Table of Contents
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions .............................................. 8
Notes on Discs ......................................... 9
Notes on region numbers ............................... 10
Table of Contents ................................... 11
Identification of Controls ....................... 12
Front panel ..................................................... 12
Rear panel ...................................................... 13
Remote control ............................................... 14
Loading batteries ........................................... 15
Operating with the remote control .................. 15
Connections
Connecting to a TV ................................. 18
Connecting to a TV ......................................... 18
Connecting to an audio system and TV
equipped with component video inputs ....... 19
Connecting to Optional Equipment ...... 20
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 21
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ............................ 21
Connecting to an amplifier equipped with a
DTS decoder ................................................ 22
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 22
Connecting to an amplifier equipped with a
digital audio input ......................................... 23
Basic playback
Playing a Disc ......................................... 26
Basic playback ............................................... 26
Variable Speed Playback ....................... 28
Playing in fast reverse or fast forward
directions ...................................................... 28
Playing frame by frame .................................. 28
Playing in slow-motion ................................... 29
Resuming playback from the same location .. 29
Locating a Desired Section ................... 30
Locating a title using the top menu ................ 30
Locating a desired section by entering the
corresponding number ................................. 31
Locating a specific chapter or track ............... 31
Advanced playback
Introduction
Introduction
Accessing a Specific Location Directly ... 34
Entering the time counter of the desired
location ......................................................... 34
Repeating a Specific Segment .............. 34
Repeating a specific segment ........................ 34
Playing in a Varied Order ....................... 35
Playing titles, chapters or tracks in a varied
order ............................................................. 35
Playing in a Favorite Order .................... 36
Setting titles, chapters, or tracks in a favorite
order ............................................................. 36
Zooming a Picture .................................. 37
Zooming a picture .......................................... 37
Selecting the Picture Enhancement
(E.P.M.) .................................................... 38
Selecting the picture enhancement ................ 38
Selecting the Sound Enhancement
(E.A.M.) ................................................... 39
Selecting the sound enhancement ................. 39
Selecting the Camera Angle .................. 40
Changing the camera angle ........................... 40
Selecting Subtitles ................................. 41
Selecting a subtitle language ......................... 41
Selecting a Language ............................ 42
Selecting a playback audio setting ................. 42
On-screen Display Operation ................ 44
On-screen display operation .......................... 44
Playing MP3/WMA Files ......................... 48
Playing MP3/WMA files .................................. 48
Viewing JPEG Files ................................ 50
Starting from a thumbnail view ....................... 50
Viewing a single image .................................. 53
Playing slide show .......................................... 55
Selecting a folder ........................................... 56
Function setup
Customizing the Function Settings ...... 60
Setting procedure ........................................... 60
Setting details ................................................. 62
Table of Languages ................................ 70
Others
Before Calling Service Personnel ......... 72
Specifications ......................................... 73
CANADIAN WARRANTY
INFORMATION ........................................ 74
11
Introduction
Identification of Controls
See the page in
Front panel
12
for details.
Introduction
Rear panel
13
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
* MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “Locating a title using the top menu.”
30
14
1
Open the cover.
2
Insert batteries (AAA size).
Operating with the remote control
Introduction
Loading batteries
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the
wrong direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
15
Connections
Read this chapter first to make all necessary
preparations.
Connecting to a TV
Connecting to an audio system
and TV equipped with
component video inputs
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Surround
Pro Logic
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with a digital audio
input
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see 43 .
Connecting to a TV
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
60
64
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
18
Interlaced outputs/inputs (ColorStream®)
Progressive outputs/inputs (ColorStream®Pro)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y,
CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows you
to view the highest quality pictures with less flicker.
Connecting to an audio system and TV equipped with component video inputs
Switching the output signal (interlaced/
progressive) using the remote control
(only when “Progressive” is set to “Enable” 62 )
You can temporarily switch the output signal for better
picture quality.
Press PROGRESSIVE on the remote control.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
60
64
If you connect a progressive TV, set
“Progressive” to “Enable” 62 .
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
19
Connections
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the
“standard definition” output. If there are questions
regarding our TV set compatibility with this model 525p
DVD player, please contact our Customer Service Center.
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
• For connection to your TV, see “Connecting to a TV”
18 19 .
• For details of output sound, see 43 .
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Notes
• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack
of the DVD video player to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is
reserved for Laserdisc use only and is incompatible with
the BITSTREAM/PCM AUDIO OUT jack of the DVD video
player.
• Connect the BITSTREAM/PCM AUDIO OUT jack of the
DVD video player to the “DIGITAL (COAXIAL)” input of a
Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.
20
Warning
• When you are connecting (via the BITSTREAM/PCM
AUDIO OUT jack) an AV decoder that does not have
Dolby Digital, Digital Theater Systems (DTS) or MPEG2
decoding function, be sure to set “Digital Output” to
“PCM” from the on-screen displays 60 64 . Otherwise,
high volume sound may damage your hearing as well
as the speakers.
• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the BITSTREAM/PCM AUDIO OUT jack
of the DVD video player.
Connecting to an amplifier equipped with a Dolby Digital decoder
Amplifier equipped with a
Dolby Digital decoder
To COAXIAL type
digital audio input
To BITSTREAM/
PCM AUDIO OUT
Connections
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
60
64
Recording system
D
43
75 Ω coaxial cable
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
60
64
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
*
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
To ANALOG
AUDIO OUT
Audio cable
21
Connections
Connecting to Optional Equipment (Continued)
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
DTS is a high quality surround technology used in theaters and now available for
Inc.
home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
• Use DVD video discs or audio
channel DTS encoded sound tracks on DVD video discs or audio CDs.
CDs encoded via the DTS
recording system.
• Make the following setting.
Amplifier equipped with
a DTS decoder
To COAXIAL type
digital audio input
To BITSTREAM/
PCM AUDIO OUT
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
or
“PCM”
60
64
Recording system
DTS
43
75 Ω coaxial cable
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with
dynamic realistic sound by connecting an amplifier equipped with an
MPEG2 audio decoder or MPEG2 audio processor.
Amplifier equipped with an
MPEG2 audio decoder
To COAXIAL type
digital audio input
To BITSTREAM/
PCM AUDIO OUT
75 Ω coaxial cable
22
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“Bitstream”
60
64
Recording system
MPEG2
43
Connecting to an amplifier equipped with a digital audio input
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“PCM”
60
64
Amplifier equipped with
a digital audio input
To COAXIAL type
digital audio input
To BITSTREAM/
PCM AUDIO OUT
75 Ω coaxial cable
23
Connections
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
Basic playback
Begin your operation.
Playing a Disc
Variable Speed Playback
Locating a Desired Section
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.
1
Press the ON/STANDBY button.
The DVD video player turns on.
The ON/STANDBY indicator on the
player illuminates.
When the DVD video player is turned on for
the first time, a message appears. Press
ENTER, and make the proper settings before
proceeding to step 2. 69
2
Press OPEN/CLOSE.
3
Place the disc on the disc tray.
The disc tray opens.
With the playback
side down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the
DVD video player to malfunction.
• Do not place a disc which is unplayable in this DVD
video player.
26
4
Press OPEN/CLOSE to close the disc
tray.
Playback starts.
If you insert a DVD video disc that contains a
top menu, a menu may appear. Use the / /
/
to select the title you want to view, then
press ENTER to start playback. See “Locating a
title using the top menu.” 30
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
Note
29 .
For resuming playback, see 30
To start playback in the stop mode
Press PLAY.
2, 4
1
STOP
PLAY
PAUSE
MENU
ENTER
TOP MENU
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
About
The
icons on the heading bar show the playable discs for the
function described under that heading.
: You can use this function with DVD video discs.
: You can use this function with VIDEO CDs.
CD
: You can use this function with audio CDs.
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
• The sound is muted during still
mode.
To stop playback
Press STOP.
To turn the power off (To enter the standby
mode)
Press ON/STANDBY to turn the ON/STANDBY indicator
off.
Note
Be aware that this equipment is still powered even after the
ON/STANDBY indicator turns off (standby mode) by pressing
the ON/STANDBY button. To disconnect this equipment
completely from the main power, pull out the power plug from
the wall outlet.
About the screen saver
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the DVD video
player automatically appears (when “Screen Saver” is
set to “On” 65 ). To turn off the screen saver, press the
PLAY button.
Automatic Power Off function
If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.
Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.
Notes
• Do not move the DVD video player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD video player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
27
Basic playback
To pause playback (still mode)
Basic playback
REV
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
FWD
PLAY
PAUSE
STOP
SLOW
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
To resume normal playback
Press PLAY.
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or
FWD button, the playback speed
changes.
Notes
• The DVD video player mutes sound and subtitles during
reverse and forward scan of DVD video discs. However, the
DVD video player plays sound during fast forward or fast
reverse play of audio CDs.
• The playback speed may differ depending on the disc.
Playing frame by frame
Press PAUSE/STEP during still playback.
To resume normal playback
Press PLAY.
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
Note
The sound is muted during frame by frame playback.
28
Playing in slow-motion
To resume normal playback
Basic playback
Press SLOW during playback.
Press PLAY.
Each time you press the SLOW
button, the slow-motion speed
changes.
Note
The sound is muted during slow-motion playback.
Resuming playback from the same location
1
Press STOP at the location where you
want to interrupt playback.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
The DVD video player memorizes
the location where playback is
stopped.
2
Press PLAY.
The DVD video player deletes the
memory of the location.
2 Press PLAY.
DVD
The DVD video player resumes
playback from the location where
you stopped playback.
Playback starts from the
beginning of the current title.
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE button before pressing the PLAY
button.
Notes
• Resuming cannot function when:
– you change the parental lock setting 67 or select a disc
menu language 65 .
– you play a PBC-featured VIDEO CD while “PBC” 68 is
set to “On”.
– you open the disc tray.
– you disconnect the power plug of the DVD video player.
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while
the DVD video player keeps a location in the memory may
function only after the memory is cleared.
29
Basic playback
TOP MENU
Locating a Desired Section
ENTER
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are
divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Chapter 1
DVD
1
Title 2
Chapter 2
Chapter 1
Chapter 2
VIDEO CD/audio CD
Chapter 3
Track 1
Track 2
Track 3
Track 4
Track 5
Locating a title using the top menu
Press TOP MENU.
The top menu appears on the TV
screen.
3
Press ENTER.
Playback starts from chapter 1 of
the selected title.
e.g.
2
30
Press
want.
/
/
/
to select the title you
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow
those instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the
actual DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
SKIP
CLEAR
PLAY
ENTER
T
Number buttons
Locating a desired section by entering the corresponding number
Press T.
If you are using a VIDEO CD/audio CD, skip step 2.
Then at step 3, enter the number for the track you
want using the number buttons.
e.g.
2
Press /
to locate.
0:03:18
Press /
section.
Repeat steps 2 and 3 if necessary.
Press PLAY or ENTER.
Playback starts from
the selected section.
to select a section you want
e.g. When you want to locate a chapter.
3
4
5
Basic playback
1
Notes
• Pressing the CLEAR button resets the numbers. To clear the
display, press the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
to enter a number of the
Also the number buttons are
available.
e.g. To enter 25
2
5
or
Locating a specific chapter or track
Press SKIP
or
repeatedly to access
the chapter or track number you want.
Playback starts from the selected chapter or track.
To locate succeeding chapters or
tracks.
Playback starts from the beginning of
the current chapter or track.
When you press twice, playback starts
from the beginning of the preceding
chapter or track.
Notes
• Some titles may not display chapter numbers.
• If you press and hold the SKIP
or
button on the
front panel during playback, the DVD video player performs
fast reverse or fast forward playback. You can vary the
speed by pressing the button repeatedly.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
normal playback, then use the SKIP
or
button.
• When you set “Title Stop” to “Off” 68 , you can access
chapters in another title. If you go back to the preceding title
by pressing the SKIP
button, the DVD video player
locates the first chapter of the title. When “Title Stop” is set
to “On,” you can access chapters only within the current title.
31
Basic playback
32
Advanced playback
Customizing the performance of your DVD video player.
Accessing a Specific Location Directly
Repeating a Specific Segment
Playing in a Varied Order
Playing in a Favorite Order
Zooming a Picture
Selecting the Picture Enhancement
(E.P.M.)
Selecting the Sound Enhancement
(E.A.M.)
Selecting the Camera Angle
Selecting Subtitles
Selecting a Language
On-screen Display Operation
Playing MP3/WMA Files
Viewing JPEG Files
Advanced playback
Accessing a Specific Location Directly
You can access a specific location by entering its corresponding time (hours,
minutes, seconds).
3
3
1
2
Entering the time counter of the desired location
1
Press T several times.
You may have to press further
depending on the disc. Press the
button repeatedly until the time
counter is highlighted.
3
Press PLAY or ENTER.
Playback starts from
the desired location.
e.g.
0:03:18
2
Press the number buttons to enter the
time.
e.g.
Notes
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD/audio CD.
Repeating a Specific Segment
CLEAR
You can specify a desired segment and repeat it.
A-B RPT
Repeating a specific segment
1
2
34
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
Press A-B RPT again at the end of the
segment (point B).
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment (A-B).
To resume normal playback
Press CLEAR or A-B RPT.
or
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 40 .
• You can specify a segment only within the current title or
track (VIDEO CD).
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Playing in a Varied Order
You can play titles, chapters within a title, or tracks in a varied order.
CLEAR
2
1
Playing titles, chapters or tracks in a varied order
1
Press PLAY MODE.
e.g.
Press PLAY.
The DVD video player starts
playback in the selected mode.
Press the PLAY button within about
5 seconds after you press the PLAY
MODE button.
To resume normal playback
VCD
CD
Press CLEAR.
Advanced playback
Each time you press the PLAY
MODE button, the playback mode
changes as follows.
2
Note
Some discs may not permit these operations.
Chapter Repeat:
Repeats the current chapter.
Title Repeat:
Repeats the current title.
Track Repeat:
Repeats the current track.
All Repeat:
Repeats the entire disc.
Chapter Random:
Plays the chapters within the current title in random
order.
Title Random:
Plays the titles in random order.
Track Random:
Plays the tracks in random order.
Random Off (Repeat Off):
Resumes normal playback.
If you press the PLAY MODE button
during playback, the DVD video
player automatically enters the
selected playback mode after
finishing the current title, chapter or
track.
35
Advanced playback
Playing in a Favorite Order
CLEAR
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 30 selections into the memory.
(Memory playback)
3
2
2
1
Setting titles, chapters, or tracks in a favorite order
1
Insert a disc and press MEMORY during
stop.
The following display appears.
e.g.
To change the programmed selections
1 While the display appears on the TV screen, press
/ / / to move the highlighted bar to the item
you want to change.
2 Change the selection following the instructions in
step 2.
To cancel the programmed selections
T: Title number
CT: Chapter number
or track number
1 While the display appears on the TV screen, press
/ to move the highlighted bar to the item you
want to cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
2
Select the items in the order you want
by pressing the number buttons, then
ENTER for each item.
36
The memory playback indicator
disappears.
Each time you press the / button, the space
of “T” and “CT” is highlighted in turn. Highlight
where you want to enter, then press the
corresponding number buttons.
To program during playback
To select another chapter in the same title, you do
not need to select the title number.
If you press the MEMORY button during playback, a
programming display appears.
Follow steps 2 and 3.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track,
then press the ENTER button for each selection
you want.
3
Press CLEAR.
Press PLAY while the display appears
on the TV screen.
The DVD video player starts
memory playback.
Notes
• Some discs may not permit memory playback operation.
• If you press the PLAY MODE button during memory
playback, the DVD video player repeats the current memory
playback.
• If you press the MEMORY or RETURN button while the
display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you turn
off the DVD video player.
Zooming a Picture
CLEAR
You can magnify areas within a picture.
ENTER
ZOOM
Zooming a picture
Press ZOOM during normal, slow or still
playback.
While “ZOOM” is selected, press ZOOM repeatedly to
turn off the icon.
Original picture is restored when the icon disappears.
Advanced playback
The DVD video player enters the
zoom playback mode and displays
the icon.
To resume normal playback
e.g.
• The ENTER button cannot cancel zoom playback if
you have turned off the icon by selecting “EXIT.” To
restore normal picture size, press the ZOOM button
to display the icon, then further press the ZOOM
button until the icon turns off.
: As you repeatedly press the ENTER
(or ZOOM) button while “ZOOM” is
selected, the magnification level
changes.
Variation of the levels includes
image reduction.
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• While the icon is displayed, the / / / buttons cannot
work on menus included on the DVD video discs. If you
want to view the menus, turn off the icon.
• The magnification level varies depending on the picture size
you select. 62
: If you press the ENTER button while
“EXIT” is highlighted, you can turn
off the icon, keeping the current
magnification level.
You can shift the highlight within the
icon by the / / / buttons.
If you press and hold the / / /
buttons, the zoom point shifts.
Pressing the CLEAR button restores
the zoom point to the center of the
picture.
37
Advanced playback
Selecting the Picture Enhancement (E.P.M.*)
You can easily select a preferred picture enhancement.
*E.P.M.: Enhanced Picture Mode
2
ENTER
1, 2
Selecting the picture enhancement
1
Press E.P.M.
The picture enhancement menu
appears.
To exit the picture enhancement selection
Press ENTER.
Alternatively leave the DVD video
player unattended for about 5 seconds
after having made a selection.
Note
Actual effect to picture may vary depending on the TV. Make
selection according to your preference.
2
Select the picture enhancement by
pressing E.P.M. or / .
Each time you press the button, the picture
enhancement changes.
Normal:
Standard black level (7.5 IRE).
Enhanced Black Level:
Enhanced Black Level (0 IRE).
Movie1:
Brightness levels raised for enhanced picture
clarity.
Movie2:
For deeper, richer color reproduction.
Animation:
For enhanced color contrast.
38
Selecting the Sound Enhancement (E.A.M.*)
You can easily switch a preferred audio enhancement.
*E.A.M.: Enhanced Audio Mode
Selecting the sound enhancement
1
The sound enhancement menu
appears.
Select the sound enhancement by
pressing E.A.M. or / .
To exit the audio enhancement selection
Press ENTER.
Alternatively leave the DVD video
player unattended for about 5
seconds after having made a
selection.
Notes
• Actual effects to sounds may vary depending on the
speaker system. Make selection according to your
preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD video player is connected to an amplifier
equipped with Dolby Surround Pro Logic, select “Normal”.
Otherwise, Dolby Surround Pro Logic may function
differently than usual.
• Selecting “Dialogue” disables “Dynamic Range Control”
function 64 .
Advanced playback
2
Press E.A.M.
Each time you press the button, the sound
enhancement changes.
Normal:
Normal sound.
3D*:
To obtain expansive virtual surround sound effects
from just two speakers.
Dialogue**:
To control dynamic range to make dialogue more
intelligible.
• To use this enhancement on sounds output from
the BITSTREAM/PCM jack, be sure to set
“Digital Output” to “PCM.” 64
* Effective in playback of a DVD video disc or a
VIDEO CD.
**Effective only during playback of Dolby Digital
recorded discs.
39
Advanced playback
Selecting the Camera Angle
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
DVD
Changing the camera angle
1
Press ANGLE while playing a scene
recorded with multiple angles.
While playing a scene recorded with
multiple angles, press the ANGLE
button.
e.g.
2
Press ANGLE or / while the angle
number is displayed on the TV screen.
Each time you press the ANGLE
button, the camera angle changes.
You can change the camera angle
directly by pressing the number
buttons corresponding to its angle
number instead of using the /
buttons.
To turn off the display, press the
CLEAR or ENTER button.
40
Notes
• You can change the camera angle during still playback. The
camera angle changes to the new setting when you resume
normal playback.
• If you pause a picture immediately after changing a camera
angle, the resumed playback picture may not display the
new camera angle.
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
SUBTITLE
CLEAR
ENTER
DVD
1
Selecting a subtitle language
Press SUBTITLE during playback.
1 Press SUBTITLE during playback.
The current subtitle setting is
displayed.
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 70
Press SUBTITLE or / while the subtitle
setting is displayed on the TV screen.
Each time you press the SUBTITLE
button, the subtitle languages
included on the DVD video disc
change.
Advanced playback
2 Press / while the subtitle setting is displayed on
the TV screen, to select “On” or “Off.”
e.g.
2
To turn subtitles on or off
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select “On.”
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc
menu.
To turn off the subtitle setting
display, press the CLEAR or ENTER
button.
Notes
• When you turn on the DVD video player or replace a disc, the player returns to the initial default setting 65 .
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language.
41
Advanced playback
Selecting a Language
1, 2
You can select a preferred language and sound recording system from those
included on the DVD video disc.
CLEAR
2
ENTER
Selecting a playback audio setting
1
Press AUDIO during playback.
The current audio setting is
displayed.
2
Press AUDIO or / while the audio
setting is displayed on the TV screen.
Each time you press the AUDIO
button, the audio settings included
on the DVD video disc change.
e.g.
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 70
Selecting sound channels of VIDEO CDs
You can switch left and right channels by pressing the
AUDIO button repeatedly during playback.
42
To turn off the audio setting display, press the
CLEAR or ENTER button.
Notes
• When you turn on the DVD video player or replace a disc,
player returns to the initial default setting 65 .
If you select a sound track which is not included on the disc,
the DVD video player plays a prior sound track programmed
on the disc.
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
Output sound conversion table
Advanced playback
• Signals of 96kHz from the BITSTREAM/PCM jack are depressed to 48 kHz by down sampling process when:
– “3D” is selected. 39
– “PCM Down Sampling” is set to “On.” 63
– a copyright protected disc is played.
• Quantization bit of signals of 20 bit or higher which is output from the BITSTREAM/PCM jack is 16 bit if they are in a
copyright protected disc.
43
Advanced playback
On-screen Display Operation
When you turn on the on-screen display, you can view information on operational
status and access features and settings.
ENTER
NAVI
On-screen display operation
Press NAVI.
The following display appears.
Each time you press the NAVI button, the on-screen display changes as follows.
See the pages in
for details on the features.
e.g. When playing a DVD video disc
44
Features
( * : There is no need to press the ENTER button.)
*:
/
*:
Chapter number
Locate a chapter using the number buttons.
31
: To stop playback. 27
: Playback starts from the beginning of the
current chapter or track. 31
: Fast reverse playback 28
: To start playback. 26
: Fast forward playback 28
Notes
• You can save only one bookmark. Setting a
new one will erase the existing one.
• There may be a difference between a marked
point and the location you actually jump to.
• Some points may not be marked.
• A bookmark cannot be set when playing a
PBC-featured VIDEO CD while “PBC” 68 is
set to “On.”
• A bookmark will be erased when:
- you turn off the power of the DVD video
player.
- you open the disc tray.
- you change the parental lock setting 67
or select a disc menu language 65 .
• If a bookmark is not set, selecting
“
” then pressing the ENTER button
during stop will start playback from the
beginning of the title or the disc. (In this case,
PBC control of a VIDEO CD will be disabled.)
• A bookmark on an MP3/WMA file always
makes you jump to the beginning of the track.
Advanced playback
Title number (Track number)
Locate a title or track using the number
buttons. 31
To jump to the bookmark:
1 During stop, press NAVI so that the
on-screen display appears.
”.
2 Press / to select “
3 Press ENTER.
: To locate succeeding chapters or tracks. 31
*:
: To begin slow motion playback. 29
Elapsed time of the current title or track
To enter the time to locate a desired location.
: To pause playback. 27
34
: Audio setting 42
: Marker
You can set a bookmark.
To set a bookmark:
1 During playback, press / to select
”.
“
2 Locate a desired point. (Pause the
playback if necessary.)
3 Press ENTER.
The point is registered as a bookmark.
: Subtitle setting 41
: Angle setting 40
(Continued)
45
Advanced playback
On-screen Display Operation (Continued)
On-screen display operation
: DNR
You can view a picture with less video noise.
Press
/
to select then press ENTER.
Off: The DNR picture enhancement does not
activate.
On: The DNR picture enhancement
activates.
Notes
• Actual picture enhancement may vary
depending on the quality of the disc.
• While the picture enhancement can provide
improvement in the reduction of noise in the
video signal, it may produce undesirable
picture artifacts on some discs. Should this
occur, select “Off.”
• Depending on the disc, some kinds of picture
details may be lost by the picture
enhancement.
: Bit rate (Mbit/s)
Amount of picture, sound and subtitle data in
the DVD video disc transferred per second.
The larger the value is, the more data
processed, but this does not necessarily insure
better picture quality.
To keep the bit rate display on-screen:
Press / to select “On” then press ENTER.
e.g.
: Closed Caption
You can display closed captions included on
a disc without connecting a closed caption
decoder to your TV.
Press / to select “On” or “Off” then press
ENTER.
Off: To disable closed captions.
On: To display closed captions.
Notes
• While you are using on-screen displays
(including the bit rate display), you cannot
view closed captions. After selecting “On”
then turning off the on-screen display, closed
captions will appear.
• When “On” is selected, some displays such
as “ ” may be disabled.
46
To turn it off, select “Off.”
The following operations also select “Off”.
– Opening the disc tray.
– Turning the power off.
ENTER
DISPLAY
Viewing the operational status
1 Press DISPLAY.
The following display appears.
2
CHAPTER
Advanced playback
TITLE
3 0:06:24 / REMAIN-0:03:57
BILLY’S FISHING GUIDE
TITLE
2: PREPARATION
EAM
EPM
ZOOM
C
2 To turn off the display, press DISPLAY again.
Notes
• The time bar will not appear when playing:
- a PBC-featured VIDEO CD while “PBC” 68 is set to
“On”.
- a menu included on a DVD video disc.
- a title which does not display the elapsed time.
• Some discs may not display the time counter.
• When playing a PBC-featured VIDEO CD while “PBC”
68 is set to “On,” the time counter may not work as
above properly.
47
Advanced playback
2
Playing MP3/WMA Files
3
You can play MP3/WMA files that have been recorded on a CD-R or CD-ROM on
the DVD video player.
PAUSE/STEP
PLAY
ENTER
NAVI
Playing MP3/WMA files
Preparations
• Make sure that a disc you want to play is compatible with this DVD video player. 49
• Set “Priority Contents” to “Audio”. 68
1
Place a CD that contains MP3/WMA files
on the disc tray.
Selecting a track (file) in the disc
1 Press NAVI twice.
2 Select the “
ENTER.
2
Press OPEN/CLOSE to load the disc.
Playback starts.
” icon using
/
then press
A list of tracks appears.
3 Press /
play.
(Pressing
/
/
/
to select a track you want to
turns the pages.)
The current track being played is highlighted in
green.
3
To stop playback, press STOP.
To pause playback
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
4 Press ENTER to begin playback of the selected
track.
Notes
• You can select a track also by designating a track number.
Press the T button, and press the / buttons to select
a track number, then press the ENTER button.
• To turn off the on-screen display, press the NAVI button
several times.
• Letters of a file/folder name overflowing the given space
are not displayed.
Notes
• Some discs may not permit this operation.
• WMA tracks copy-protected cannot be played.
• The BITSTREAM/PCM jack outputs MP3/WMA sounds in the linear PCM format regardless of the current “Digital Output”
selection 64 43 .
• If you stop playback by pressing the STOP button, and then press the PLAY button, playback will start from the beginning of
the track.
• The SKIP 31 and PLAY MODE 35 functions are also available.
48
Playable files
Advanced playback
MP3/WMA disc compatibility with this player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
• Sampling Frequency:
44.1 kHz only
• Bit rate:
WMA: 48 kbps - 192 kbps (CBR)
MP3: 32 kbps - 320 kbps (CBR)
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “MP3” or
“WMA” extension.
e.g.“********.MP3”, “********.WMA”
• Total number of folders:
Less than 256
• Total number of files:
Less than 1000
• WMA codec version:
V7 or V8 (Stereo sound only)
This DVD video player requires discs/recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are many
different types
of recordable disc formats (including CD-R containing
MP3/WMA files). Given the fact that technology in this
area is still maturing, Toshiba cannot guarantee that all
genre of recordable discs will produce optimal playback
quality. The technical criteria set out in this owner’s
manual are meant as a guide only.
Customers should also note that permission is required
in order to download MP3 files and music from the
internet. Toshiba has no right to grant such permission.
Permission should always be sought from the copyright
owner.
Microsoft, Windows Media, and the Windows
Logo are trademarks or registered trademarks
of Microsoft Corporation in both the United
States and other countries.
49
Advanced playback
Viewing JPEG Files
You can play JPEG files that have been recorded on a CD-R or CD-ROM on the DVD video player.
You can select a preferred view: a page of 6 thumbnail images, a single image view, and slide
show of a selected folder.
Also, rotating, enlarging and shifting of each image can be possible.
Thumbnail view
Single image view
Slide show
Starting from a thumbnail view
Preparations
• Prepare a disc that contains JPEG files you want to view. 57
• Set “Priority Contents” to “Photo”. 68
• Make your TV shape conform to the 4:3 picture size. Only 4:3 pictures can be played regardless of the function
settings via the on-screen displays of the DVD video player. If the TV is adjusted to other sizes, e.g. “WIDE,”
images will appear to be horizontally expanded. For details, refer to the owner’s manual of your TV.
1
Press OPEN/CLOSE to open the disc tray.
2
3
Place a disc that contains JPEG files on the disc tray.
Press OPEN/CLOSE.
The disc tray closes, and the DVD video player reads the loaded disc.
After completion of reading, the DVD video player enters either of the following modes, and provides the
respective displays, depending on the condition of the disc contents. Proceed to steps described below.
A thumbnail view appears.
(Automatic mode)
Proceed to step 4 on 51 .
50
A list of folders in the disc appears.
(Selection mode)
Refer to 56 , “Selecting a folder.”
1, 3
4
6
4
4
4
Turn the page if necessary.
Press / / / to select the last image of 6, then press .
(Press / / / to select the first image of 6, then press .)
(or
Advanced playback
Selecting
) then pressing the ENTER button also turns the pages.
Alternatively,
Press SKIP.
: To view the succeeding 6 images.
: To view the previous 6 images.
The page changes as follows:
1
4
2
5
3
6
7 8 9
10 11 12
SKIP
7 8 9 13 14 15
10 11 12 16 17 18
5
Select the viewing options at your preference.
- Viewing a single image: See 53 .
- Playing slide show: See 55 .
6
To quit the JPEG playback, press STOP.
SKIP
13 14 15 19 20 21
16 17 18 22 23 24
• If you press the PLAY button after pressing the STOP button, you can return to the thumbnail
view.
• Pressing the OPEN/CLOSE button to open the disc tray can also quit the playback.
Notes
• If you display a thumbnail view from the automatic mode and leave it unattended for approximately 20 seconds, slide show
starts automatically.
• When “Screen Saver” is set to “On” 66 , a thumbnail view which is unattended for about 10 minutes automatically changes
to slide show.
• Some files may not display their own entire images depending on the size.
51
Advanced playback
Viewing JPEG Files (Continued)
ANGLE
ENTER
Starting from a thumbnail view
To reverse the order
To display a folder list
Some cameras may have given the first file number
(e.g. 01) always to the latest photo. When you play
such files, reverse the order of images. You can view
them in order of time.
1 Press
Press /
ENTER.
/
/
to select “
/
/
/
to select “
”.
” then press
2 Press ENTER.
A folder list appears.
Note
The order of images will be restored when you open the
disc tray or turn the power off.
To set an image rotation on a thumbnail view
1 Select an image by pressing
/
/
/
.
2 Press ANGLE repeatedly.
Each time you press the ANGLE
button, you can set a rotation of the
image in 90° increment.
52
You can select a folder to play. For details, see page
56 .
3
MENU
1
2
T
Viewing a single image
1
On a thumbnail view, select an image by
pressing / / / .
To change the image
To view the succeeding image, press
or ENTER.
To view the previous image, press
2
3
.
Press ENTER.
Advanced playback
or
The selected image is
displayed.
To quit the JPEG playback, press STOP.
• If you press the PLAY button after
pressing the STOP button, slide
show 55 starts.
• Pressing the OPEN/CLOSE button
to open the disc tray can also quit
the playback.
Notes
• Change of images will be reversed if you reverse the
order of images.
• You can view the succeeding image also by pressing the
PAUSE/STEP or SKIP
button.
To reverse the order
1 Press MENU.
The following menu appears for
about 5 seconds.
e.g.
Notes
• Some files may not display their own entire image
depending on the size.
• When “Screen Saver” is set to “On” 66 , a single image
which is unattended for about 10 minutes automatically
changes to slide show.
To confirm a photo number
2 Press
/
to select “Reverse” then press ENTER.
Press T.
Notes
• To turn it off, press the T button.
• You can locate an image by entering its number. While
displaying a photo number, press the number buttons to
enter a number then press the ENTER button. Slide show
will start from the located image.
Note
Whenever you change the order, the first or last of images
to be played will be located.
53
Advanced playback
Viewing JPEG Files (Continued)
ANGLE
MENU
ZOOM
ENTER
Viewing a single image
To magnify an image
To display a folder list
Press ZOOM repeatedly.
1 Press MENU.
The following menu appears for
about 5 seconds.
e.g.
Each time you press the ZOOM button, the
magnification level changes as follows:
“Zoom Off” (The icon and monitor scope appear.)
“Zoom1”
“Zoom2”
“Zoom3” (Maximum)
“Shrink”
Original size (The icon and monitor
scope disappear.)
2 Press
Notes
• To turn off the icon and monitor scope, press the
/ / / buttons to select “EXIT” in the icon, then
press the ENTER button.
• While changing the magnification level, you can shift the
image. Press and hold the / / / buttons.
• Exiting an image cancels the current selection of the
magnification level.
To rotate an image
Press ANGLE repeatedly.
/
to select “List” then press ENTER.
A folder list appears.
You can select a folder to play. For details, see
page 56 .
To return to the thumbnail view
1 Press MENU.
The image rotates by clockwise 90
degree.
Notes
• If you rotate an image of which magnification level is
changed, the size of the image is restored momentarily.
• The DVD video player may redo displaying an image if
you rotate it.
54
2 Press /
ENTER.
to select “Thumbnail” then press
3
2
PAUSE/STEP
Playing slide show
1
On a thumbnail view, select an image
from which you want to start slide
show.
2
Press PLAY.
See 53 .
To magnify an image
See 54 .
Note
Slide show pauses if you press the ZOOM button.
To rotate an image
Slide show starts.
See 54 .
Advanced playback
You can skip this step. Slide show will start from a
photograph currently selected.
To confirm a photo number
To display a folder list
3
To quit the JPEG playback, press STOP.
See 54 .
To return to the thumbnail view
• If you press the PLAY button after
pressing the STOP button, the
slide show resumes.
• Pressing the OPEN/CLOSE button
to open the disc tray can also quit
the playback.
See 54 .
To view a single image (To pause slide show)
Press PAUSE/STEP.
55
Advanced playback
Viewing JPEG Files (Continued)
2, 3, 5
1
4
Selecting a folder
You can designate a folder to play.
1
On a single image view or during slide
show, press MENU.
The following menu appears for
about 5 seconds.
4
Press
5
After thumbnails appear in the
background, press ENTER.
e.g.
To display a folder list also from a thumbnail view,
follow the procedure on 52 , and skip to step 3.
2
Press /
ENTER.
to select “List” then press
A folder list appears.
/
to select a folder.
: If you press this button while
selecting a sub folder, you can
view the contents of the folder.
• Sub folders will appear if
contained in the selected
folder.
• If the selected folder contains a
file to view, a thumbnail image
of the file will appear in the
background.
: If you press this button while
selecting a current folder, you
can go back to the previous
folder.
The thumbnail view of the current
folder appears.
For operations of thumbnail view,
see 51 .
Notes
• The first thumbnail view provided by the automatic mode
may not return once you display a folder list. You can retrieve
it if you load the disc again.
• Letters of a folder/path name overflowing the given space
are not displayed.
3
56
Press
/
to select a folder.
JPEG files compatibility
Discs whose compatibility with this DVD video player which have been confirmed by TOSHIBA are as follows.
Many of these discs, when loaded, will make the DVD video player enter the automatic mode 50 to play a prescribed
folder in the disc. To play other folders, display a folder list and select a folder.
JPEG disc compatibility with this DVD video player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “JPG”
extension.
e.g.“********.JPG”
• Total number of folders:
Less than 256
• Total number of files:
Less than 1000
Advanced playback
CANON QuickCD
FUJICOLOR CD
Kodak Picture CD
NORITSU QSS CD
Some files may not display their own entire image depending on the size.
Some discs may not permit this operation. Especially, the following conditions of included files will increase the disc’s
disability.
1. Pixels over 3072 x 2048 in height and/or width
2. File format except Exif
57
Advanced playback
58
Function setup
You can change the default settings to customize
performance to your preference.
Customizing the Function
Settings
Table of Languages
Function setup
Customizing the Function Settings
3, 4
You can change the default settings to customize performance to your
preference.
RETURN
2
1, 6
Setting procedure
1
2
Press SETUP during stop.
The following on-screen display
appears.
3
Press / to select the setting you
want to change, then press ENTER.
4
Change the selection by / or other
buttons, by referring to the
corresponding pages ( 62 – ), then
press ENTER.
5
Repeat steps 3 and 4 to change other
settings.
6
Press SETUP.
Press / to select a symbol for the
setting you want to change.
(See the next page.)
Picture performance settings
Output sound settings
To select another operation, go back to step 2.
The on-screen display disappears.
Language settings
To return to the previous display
Display settings
Press RETURN.
Operational settings
Initial setup
60
Notes
• To quit the procedure, press the SETUP button to turn off
the on-screen display.
• The SETUP button can function even during normal
playback, however some operations may be inaccessible,
and a message will appear. In this case, try again after
playback is stopped.
Setting
Details
Page
TV Shape
To select a picture size according to the aspect
ratio of your TV.
62
Progressive
To select whether you send progressive
signals to the connected TV or not.
62
Progressive Conversion
DVD
To select the system of output signal. (Only
when connected to a PROGRESSIVE TV.)
62
Pause/Still
DVD
To select the resolution of still pictures.
63
PCM Down Sampling
DVD
To select a sound processing option for PCM
sounds if they are high frequency signals of 96
kHz.
63
To select an output sound format corresponding 64
to your system connection.
Digital Output
Dynamic Range Control
DVD
Karaoke Vocal
DVD
Disc Menu Language
DVD
64
To turn on or off the vocal output during DVD
KARAOKE disc playback.
64
To select a preferred language for on-screen
displays.
65
To select a preferred language for disc menus.
65
DVD
To select a preferred language for the sound
track.
65
DVD
To select a preferred language for subtitles.
65
On-Screen Displays
To turn on or de-activate the operational status
display on the TV screen.
66
Background
To select the background color or background
picture.
66
To turn the screen saver on or off.
66
To turn the parental lock function on or off.
67
To turn on or off a feature that automatically
stops playback after a title has been viewed.
68
PBC
To use the menu screen when playing a PBCcontrollable VIDEO CD.
68
Priority Contents
To select the playback priority between JPEG
(picture) files and MP3/WMA (audio) files.
68
On-Screen Language
TV Shape
To install the initial system setting.
69
Audio Language
Subtitle Language
Screen Saver
Parental Lock
Title Stop
DVD
DVD
DVD
Function setup
On-Screen Language
To turn on or off a function that makes faint
sounds easier to hear even if you lower the
volume during late hours playback.
61
Function setup
Customizing the Function Settings (continued)
Setting details
Progressive
Disable:
Select when a standard (nonprogressive) TV is connected. 18 19
Enable:
Select when a progressive TV is
connected. 19
Press PROGRESSIVE on the remote
control to switch the output signal for
better picture quality.
TV Shape
4:3 Letterbox:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
4:3 Normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
Note
When “Enable” is set and you select the progressive
output signal, no video signals are output from the
VIDEO OUT jack and the S VIDEO OUT jack.
Progressive Conversion
16:9 Widescreen: Select when a 16:9 wide TV is
connected.
16:9 Shrink:
Select when a 16:9 wide
progressive TV is connected and it
cannot fit 4:3 video signal
automatically to its 16:9 screen.
Displays 4:3 pictures of the
progressive video signal in the
correct ratio with masking bars to
the left and right of the picture.
Notes
• The displayable picture size is preset on the DVD
video disc. Therefore, the playback picture of some
DVD video discs may not conform to the picture size
you select.
• If you select “16:9 Widescreen” and you own a 4:3 TV
set, the DVD playback picture will be horizontally
distorted during playback. Images will appear to be
horizontally compressed. Always be sure that your TV
shape conforms to the actual TV in use.
62
DVD
There are two types of source content in pictures
recorded in DVD video discs: film content (pictures
recorded from films at 24 frames per second) and
video content (video signals recorded at 30 frames
per second). Make this selection according to the
type of content being viewed.
Auto: Select this position normally.
The DVD video player automatically detects
source content, film or video, of playback
source, and converts that signal to the
progressive output format in an appropriate
method.
Video: The DVD video player filters video signal, and
converts it to the progressive output format
appropriately.
Suitable for playback of video content
pictures.
Film: The DVD video player converts film content
pictures to the progressive output format
appropriately.
Suitable for playback of film content pictures.
The progressive output feature will be most
effective under this selection.
Note
Depending on the disc, pictures may be cut off or
doubled. In this case, select “Video.”
Pause/Still
DVD
Auto:
For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
more clearer when you pause it.
PCM Down Sampling
DVD
Function setup
According to performance of your connected audio
system, select a sound processing option for
playback of a disc that contains high frequency
signals (sampling frequency 96 kHz).
Off: Select when you make a connection via the
ANALOG AUDIO OUT jacks.
The DVD video player outputs PCM signals
with no conversion.
However, if the PCM signals are copyprotected, they are not output from the
BITSTREAM/PCM DIGITAL AUDIO jack,
unless they are 48 kHz/16 bit signals.
Auto: Select when your connected audio system
processes high frequency signals of 96 kHz.
The DVD video player outputs PCM signals
with no conversion.
However, if the PCM signals are copyprotected, they are down-sampled to 48 kHz/
16 bit.
On: Select when your connected audio system
does not process high frequency signals of 96
kHz.
The DVD video player down-samples PCM
signals to 48 kHz.
Note
If you select “Off” or “Auto” because your connected
audio system does not process high frequency signals
of 96 kHz, you will not hear output sound from those
signals.
63
Function setup
Customizing the Function Settings (continued)
Setting details
Digital Output
Karaoke Vocal
Select the output sound format corresponding to
your system connection.
For details of sound recording systems, see 43 .
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded
on the disc.
Bitstream:
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
MPEG1 or MPEG2 decoder. 21 22
The DVD video player outputs digital
audio information in the bitstream
format when you play a DVD video disc
recorded on the Dolby Digital, DTS,
MPEG1 or MPEG2 recording system.
Notes
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE
discs. This feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
• When playing KARAOKE, connect appropriate audio
equipment such as an amplifier to the DVD video
player.
PCM:
Select when connected to a 2 channel
digital stereo amplifier. 23
The DVD video player outputs sounds
in the PCM 2ch format when you play
a DVD video disc recorded on the
Dolby Digital, MPEG1 or MPEG2
recording system.
Note
When you make a connection to a TV, or Dolby
Surround Pro Logic or stereo system via the analog
audio jacks, select “Bitstream” or “PCM.”
Dynamic Range Control
DVD
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
Note
The level of Dynamic Range Reduction may differ
depending on the DVD disc.
64
DVD
Audio Language
English: To play sound tracks in English.
French: To play sound tracks in French.
Spanish: To play sound tracks in Spanish.
Italian: To play sound tracks in Italian.
German: To play sound tracks in German.
Others: To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
On-Screen Language
English:
French:
Spanish:
Italian:
German:
Others:
1) Obtain the abbreviation of the preferred
language from the list 70 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the / buttons.
Function setup
English: To view on-screen displays in English.
Français: To view on-screen displays in French.
Español: To view on-screen displays in Spanish.
Italiano: To view on-screen displays in Italian.
Deutsch: To view on-screen displays in German.
Disc Menu Language
DVD
DVD
To display disc menus in English.
To display disc menus in French.
To display disc menus in Spanish.
To display disc menus in Italian.
To display disc menus in German.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 70 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the /
buttons.
4) Press the ENTER button.
Note
Some DVD video discs may be played in a different
language than you selected. A prior language may be
programmed on the disc.
Subtitle Language
English:
French:
Spanish:
Italian:
German:
No Subtitle:
Others:
4) Press the ENTER button.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
DVD
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
To display subtitles in Italian.
To display subtitles in German.
To disable subtitles.
To make a further choice.
After pressing the ENTER button,
follow steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 70 .
2) Select the first character by pressing the
buttons.
/
(Continued)
65
Function setup
Customizing the Function Settings (continued)
Setting details
(Continued)
3) Press the / buttons to shift and select the
second character by pressing the / buttons.
On-Screen Displays
4) Press the ENTER button.
Notes
• Some DVD video discs may be set to display subtitles
in a different language than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc
menu.
Off: Operational modes (e.g. “
displayed.
On: Operational modes (e.g. “
displayed on-screen.
”, “
”) are not
”, “
”) are
Background
Blue:
Blue background.
Gray:
Gray background.
Picture: To use the picture which appears when you
turn on the DVD video player as a
background.
Jacket: To use the jacket picture included on some
DVD video discs as a background. If it is
not included, a gray background will be
substituted.
Screen Saver
DVD
Off: The screen saver is disengaged.
On: The screen saver operates.
66
1) Press the number buttons to create a personal
4-digit security code, then press the ENTER
button.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
Parental Lock
DVD
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the DVD
video player. Make sure this function works with your
DVD video discs.
Off: The parental lock feature does not function.
After pressing the ENTER button, follow step 1)
below.
On: To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3) below.
Country/Area
AUSTRALIA
BELGIUM
CANADA
CHINA
CHINA HONG KONG
DENMARK
FINLAND
FRANCE
GERMANY
INDONESIA
ITALY
JAPAN
MALAYSIA
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
Code
AU
BE
CA
CN
HK
DK
FI
FR
DE
ID
IT
JP
MY
NL
NO
PH
RU
SG
ES
SE
CH
TW
TH
GB
US
Function setup
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the way
a DVD video disc can be controlled may vary from
disc to disc. For example, if the disc allowed you
could edit out violent scenes unsuitable for children
and replace them with more suitable scenes, or lock
out playback of the disc altogether.
2) Enter the code of a country/area whose
standards were used to rate the DVD video
disc, referring to the list below.
a) Select the first character by pressing the
/ buttons.
b) Press the / buttons to shift and select
the second character by pressing the /
buttons.
c) Press the ENTER button.
(Continued)
67
Function setup
Customizing the Function Settings (continued)
Setting details
(Continued)
3) Press the / buttons to select the parental
lock level, then press the ENTER button.
Title Stop
DVD
Off: The DVD video player continues after playback
of a title is completed.
On: The DVD video player stops after playback of a
title is completed.
PBC
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select level 7, discs rated
higher than level 7 are locked out and cannot be
played.
The parental lock level is equivalent to the following
USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
The parental lock levels for other countries/areas
than U.S. are included for future use. Check the
appropriate parental lock level when you buy a DVD
video disc equipped with the parental lock feature in
the future.
To change the parental lock level
Follow steps 1) - 3).
To change your 4-digit security code
1) After selecting “On” or “Off,” press the STOP
button four times, then press the ENTER
button.
The 4-digit security code is cleared.
2) Press the number buttons to create a new
4-digit security code.
3) Press the ENTER button.
68
Off: When playing a VIDEO CD without using the
menu.
On: To use the menu when playing a PBC-featured
VIDEO CD.
At stop mode, you can also simply press PBC button
on remote control to select PBC on or off.
Priority Contents
To select the playback priority between JPEG (picture)
files and MP3/WMA (audio) files.
Photo:
Audio:
JPEG files take priority over MP3/WMA
files.
MP3/WMA files take priority over JPEG
files.
Note
If this selection does not correspond to disc contents,
the DVD video player will take a longer time to start
playback of the disc.
Initial Setup
1) Press the / buttons to select “On-Screen
Language,” and press the ENTER button.
Function setup
2) Select a language pressing the
and press the ENTER button.
/
buttons,
See page 65 , “On-screen Language.”
3) Make your selection in the same manner as
step 1) then step 2).
See page 62 , “TV Shape.”
69
Function setup
Table of Languages
Table of languages and their abbreviations
Abbreviation
–––
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
70
Language
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
Others
Before Calling Service Personnel
Specifications
CANADIAN WARRANTY
INFORMATION
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
18
The DVD video player turned
off by itself.
• The automatic power off function turned
the unit off.
• Press the PLAY button.
27
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
video player appears on the TV screen.
26
• The video cable is not connected
securely.
• Connect the video cable securely into
the appropriate jacks.
18, 19
• The equipment connected with the audio
cable is not set to receive DVD signal
output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD video player.
26
• The audio cable is not connected
securely.
• Connect the audio cable securely into
the appropriate jacks.
18 – 23
• The audio receiver or TV is turned off.
• Turn on the equipment connected with
the audio cable.
26
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
• It is in fast forward or fast reverse
playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
–
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the DVD video player directly to
the TV. Avoid connecting the DVD video
player to a VCR or TV/VCR combination.
18
The DVD video player does
not start playback.
• No disc is inserted.
• Insert a disc.
26
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and color system.)
10
• The disc is placed upside down.
• Place the disc with the playback side
down.
26
• The disc is not placed within the guide.
• Place the disc correctly inside the guide
on the disc tray.
26
• The disc is dirty.
• Clean the disc.
• The parental lock function is set.
• Cancel the parental lock function or
change the parental lock level.
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback,
memory playback, etc.
• These operations may prevent a proper
progress of the contents.
–
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity
may interrupt correct operations.
• Press and hold the ON/STANDBY
button on the front panel for more than
about 3 seconds. The DVD video player
turns off. Press the button again to turn
it on. If the buttons still do not work,
disconnect the power plug and insert it
into the wall outlet again.
–
The remote control does not
work properly.
• The remote control is not pointed at the
remote sensor of the DVD video player.
• Point the remote control at the remote
sensor of the DVD video player.
15
• The remote control is too far from the
DVD video player.
• Operate the remote control within about
7 m.
15
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
15
No sound.
72
Page
43, 60
64
9
60, 67
Specifications
DVD video player / outputs / supplied accessories
DVD Video Player
Power supply
120 V AC, 60 Hz
Power consumption
14 W
Mass
1.7 kg
External dimensions
430 x 50 x 200 mm (W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range
DVD linear sound :
Signal-to-noise ratio
More than 100 dB
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
More than 93 dB
Harmonic distortion
Less than 0.005 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Others
Audio dynamic range
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack x 2
Audio output (BITSTREAM/PCM
COAXIAL)
0.5V (p-p), 75 Ω, pin jack x 1
Audio output (ANALOG)
2.0 V (rms), 680 Ω, pin jacks (L, R) x 1
Supplied Accessories
Audio/video cable .................................................. 1
Remote control (SE-R0127) .................................. 1
Batteries (AAA) ...................................................... 2
• Designs and specifications are subject to change without notice.
73
Others
- IMPORTANT CANADIAN WARRANTY INFORMATION
GARANTIE CANADIENNE
STANDARD WARRANTY
TYPE OF SET
WARRANTY PERIOD
DVD Player
DVD/VCR Combination
Home Theatre in a Box
DVD Recorder
Portable DVD
12 MONTHS
CANADIAN WARRANTY
GARANTIE NORMALE
TYPE D’APPAREIL
DURÉE DE LA GARANTIE:
Lecteur DVD
DVD/magnétoscope combo
Cinéma maison dans une boîte
Enregistreur DVD
DVD Portatif
12 MOIS
GARANTIE CANADIENNE
Toshiba of Canada Limited (TCL) makes the following
limited warranties to original consumers in Canada. Please
retain your “Bill of Sale” as proof of purchase. To obtain a
“Canadian Warranty” please register online at
www.toshiba.ca.
1) Toshiba du Canada Limit e (TLC) of fre au Canada les
garanties limit es suivantes aux consommateurs origin-aux.
Veuillez conserver votre < facture > comme preuve d’achat.
Pour obtenir une garantie canadienne, veuillez vous
inscrire en ligne à www.toshiba.ca.
Canadian Warranty Information
Should service be required on this unit during the one year
warranty period, TCL’s option will be to repair or exchange the
defective unit. It will be necessary to follow this procedure:
Contact: Toshiba of Canada Limited at the Consumer
Electronics Group, customer support line.
Phone:
1-800-268-3404
Email:
[email protected]
Information sur la garantie Canadienne
Si vous avez besoin de service sur cet appareil au cours le
l’année de garantie, Toshiba du Canada Limitée aura l’op tion de
réparer ou échanger l’appareil d féctueux. Vous devrez suivre la
procédure suivante:
Contact: Toshiba du Canada Limitée au Groupe Électronique
aux consommateurs, service à la clientèle.
Tél:
1-800-268-3404
Courriel: [email protected]
All in-warranty repairs must be made by an authorized TCL
service centre.
For service exchange TCL will arrange to have the unit picked
up by courier and a replacement unit will be returned via same
courier. (Note: A major credit card number will be required as a
charge of $25.00 will apply if no fault is found with the unit.)
During the first 3 months of ownership, a new unit will be
supplied as a replacement. During the remainder of the
warranty period a service-renewed unit will be supplied.
The original “Bill of Sale” must be provided as proof of
purchase (it will be returned with the replacement unit.)
This 12-month warranty will be strictly adhered to.
Out of warranty units should be repaired by a TCL authorized
service centre.
Note: It is the responsibility of the owner to ensure proper
packaging. Should damage in shipping occur, due to poor
packaging, a charge back for the repair will result. This
warranty applies to the original purchaser only and is not
transferable.
This warranty does not apply to sets that have been subjected
to misuse, neglect, accident, physical damage or acts of
nature.
Sets with the serial number removed, altered, replaced or
defaced will not be covered by this warranty.
The warranties from TCL are effective only if the product is
purchased in Canada from an authorized TCL dealer and
operated in Canada.
Products utilized for rental or commercial purposes are not
covered by this warranty.
This warranty is in lieu of all other warranties, guaranties or
agreements, whether expressed or implied, and no person,
agent distributor, dealer, service centre or company is authorized to change, modify or extend its terms in any manner
whatsoever.
Toutes les réparations au cours de la garantie doivent être faites
par un centre de service autorisé Toshiba.
Pour un échange TCL s’assurera qu’un service de courrier
ramassera l’unité et qu’un appareil de remplacement soit expédié
par le même service de courrier
(Note: Un numéro de carte de crédit sera requis car une charge
de 25,00$ sera appliquée si toutefois l’appareil n’avait aucun
problème de fonctionnement.)
Une nouvelle unité sera fournie comme remplacement durant les
premiers 3 mois de propriété. Par contre durant la balance de la
garantie une unité remise à neuf sera fournie.
La <facture> originale doit être fournie comme preuve d’achat
(elle vous sera retournée avec l’unit de remplacement.)
Cette garantie de 12 mois sera strictement adhérée.
Les unités hors de garantie devraient être réparées par un centre
de service autorisé Toshiba.
Note: C’est la responsabilité du propriétaire de s’assurer que
l’emballage est adéquat. Vous serez facturé pour toutes réparations causées par des dommages encourus à cause d’un
emballage non adéquat.
Cette garantie est octroyée à l’acheteur initial et n’est pas
transférable. Cette garantie ne s’aplique pas aux appareils qui
ont été sujets aux abus, négligences, accidents, dommages
physiques ou actes naturels.
Les appareils dont le numéro de série a été enlevé, altété,
remplacé ou barbouillé ne sont pas couverts par cette garantie.
Les garanties de TCL sont valides seulement sur les unités sont
achetées et utilisées au Canada d’un marchand autorisé TCL.
Cette garantie ne couvre pas les produits de location ou à usage
commercial. Cette garantie remplace toutes autres garanties ou
ententes exprimées ou sous-entendues. Aucune personne, agent,
distributeur , concessionaire ou compagnie n’est autorisé à
changer, modifier ou prolonger les termes de cette garantie de
quelque façon que ce soit.
Toshiba of Canada Limited 191 McNabb Street Markham, Ontario L3R 8H2
74
Memo
Others
75
Printed in China
811-SD39A1-090
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement