USER`S MANUAL
www.proform.com
Model No. PFEX13813.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
ACTIVATE YOUR
WARRANTY
To register your product and
activate your warranty today,
go to www.proformservice.com/
registration.
CUSTOMER CARE
For service at any time, go to
www.proformservice.com.
Or call 1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USER’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s).
If a decal is missing or illegible, see the front cover
of this manual and request a free replacement decal.
Apply the decal in the location shown. Note: The
decal(s) may not be shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on the exercise bike before using the exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. It is the responsibility of the owner to ensure
that all users of the exercise bike are adequately informed of all precautions.
8. Keep children under age 12 and pets away
from the exercise bike at all times.
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
10. The exercise bike should not be used by
persons weighing more than 350 lbs.
(159 kg).
3. Use the exercise bike only as described in
this manual.
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a commercial, rental, or institutional setting.
11. Be careful when mounting and dismounting
the exercise bike.
12. Always keep your back straight while using
the exercise bike; do not arch your back.
5. Keep the exercise bike indoors, away from
moisture and dust. Do not put the exercise
bike in a garage or covered patio, or near
water.
13. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
6. Place the exercise bike on a level surface
with at least 2 ft. (0.6 m) of clearance around
the exercise bike. To protect the floor or
carpet from damage, place a mat under the
exercise bike.
14. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
3
4
STANDARD SERVICE PLANS
all
5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
4.0 RT exercise bike. The 4.0 RT exercise bike provides an impressive selection of features designed
to make your workouts at home more effective and
enjoyable.
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions after
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 4 ft. 11 in. (150 cm)
Width: 2 ft. 3 in. (69 cm)
Console
Handlebar
Accessory Tray
Pedal/Strap
Backrest
Seat
Wheel
Heart Rate Monitor
Adjustment Handle
Handle
Leveling Foot
6
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M6 Washer
(88)–8
M6 x 18mm
Screw (25)–4
M10 x 16mm
Screw (75)–4
M10 Split
Washer (36)–4
M6 x 30mm
Screw (70)–4
M8 x 16mm
Screw (69)–4
M4 x 16mm
Screw (77)–5
M8 x 38mm Screw (67)–4
M10 x 105mm Screw (65)–4
7
ASSEMBLY
• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.
• To identify small parts, see page 7.
• In addition to the included tool(s), assembly
requires the following tools:
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
one Phillips screwdriver
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
one adjustable wrench
1. Go to www.proformservice.com/registration
on your computer and register your product.
1
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
2. Orient the Front Stabilizer (15) so that the indicated hole is facing the pin on the Frame (1).
2
While a second person lifts the front of the
Frame (1), attach the Front Stabilizer (15) to the
Frame with two M10 x 105mm Screws (65).
15
65
Hole
Pin
1
8
3. While a second person lifts the rear of the Frame
(1), attach the Rear Stabilizer (16) to the Frame
with two M10 x 105mm Screws (65).
3
16
1
65
4. Orient the Seat Handlebar (10) as shown.
4
67
Attach the Seat Handlebar (10) to the Seat
Carriage (41) with four M8 x 38mm Screws (67).
Plug the Seat Handlebar Wire (A) into the
Receptacle (42) in the right side of the exercise
bike.
10
41
42
9
A
5. Attach the Seat (9) to the Seat Handlebar (10)
with four M6 x 18mm Screws (25) and four M6
Washers (88). Note: Only two Screws and two
Washers are shown.
5
9
10
88
25
6. Slide the Backrest Back (86) onto the Seat
Handlebar (10).
6
Attach the Backrest Back (86) with four M6 x
30mm Screws (70) and four M6 Washers (88);
start all the Screws, and then tighten them.
86
88
70
10
10
7. Orient the Upright (2) and the Top Shield (44)
as shown. Slide the Top Shield upward onto the
Upright.
7
Wire Tie
Have a second person hold the Upright (2) and
the Top Shield (44) near the Frame (1) until
step 8 is completed.
2 Wire
Tie
42
Locate the wire tie in the Upright (2). Tie the
lower end of the wire tie to the Main Wire (43)
and to the Frame Pulse Wire (42). Next, pull the
upper end of the wire tie until the Main Wire and
the Frame Pulse Wire are routed through the
Upright.
43
44
1
Tip: To prevent the wires from falling into the
Upright (2), secure the wires with the wire tie.
8. Tip: Avoid pinching the wires. Slide the
Upright (2) onto the Frame (1).
8
Attach the Upright (2) with four M10 x 16mm
Screws (75) and four M10 Split Washers (36).
Tip: Tighten the two Screws in the front of
the Upright, and then tighten the other two
Screws.
Avoid pinching
the wires
75
2
36
44
1
Slide the Top Shield (44) downward and press it
onto the Left and Right Front Shields (13, 14).
36
13, 14
11
75
9. Identify the Right Handlebar (20) and orient it as
shown.
9
Attach the Right Handlebar (20) to the Upright
(2) with two M8 x 16mm Screws (69).
69
Attach the Left Handlebar (7) in the same
way.
7
2
69
20
10. Identify the Rear Upright Cover (57) and orient it
as shown.
10
Attach the Rear Upright Cover (57) to the Upright
(2) with an M4 x 16mm Screw (77).
57
77
12
2
11. Untie and discard the wire ties on the Main Wire
(43) and the Frame Pulse Wire (42).
11
While a second person holds the Console (4)
near the Upright (2), connect the wires on the
Console to the Main Wire (43) and to the Frame
Pulse Wire (42).
4
43
2
Then, insert the excess wires into the Upright (2).
42
Avoid pinching
the wires
12. Tip: Avoid pinching the wires. Locate the two
console screws in the back of the Console (4).
Slide the console screws upward into the indicated slots in the Upright (2).
12
4
Then, attach the Console (4) to the Upright (2)
with two M4 x 16mm Screws (77).
2
77
Slots
Screws
Avoid pinching
the wires
13. Identify the Front Upright Cover (58) and orient it
as shown.
13
58
77
Attach the Front Upright Cover (58) to the
Upright (2) with two M4 x 16mm Screws (77).
2
13
14. Identify the Right Pedal (21).
14
Using an adjustable wrench, firmly tighten the
Right Pedal (21) clockwise into the Right Crank
Arm (23).
Strap
Post
Firmly tighten the Left Pedal (not shown)
counterclockwise into the Left Crank Arm (not
shown).
23
If necessary, press the right strap onto the
post on the Right Pedal (21). To loosen the
strap, press the indicated tab and pull the strap
upward. To tighten the strap, simply pull the end
of the strap downward. Adjust the strap on the
Left Pedal (not shown) in the same way.
15. Plug the Power Adapter (51) into the receptacle
on the front of the exercise bike.
21
Tab
15
51
Note: To plug the Power Adapter (51) into an
outlet, see HOW TO PLUG IN THE POWER
ADAPTER on page 15.
16. After the exercise bike is assembled, inspect it to make sure that it is assembled correctly and that it
functions properly. Make sure that all parts are properly tightened before you use the exercise bike.
Note: Extra parts may be included. Place a mat beneath the exercise bike to protect the floor.
14
HOW TO USE THE EXERCISE BIKE
HOW TO PLUG IN THE POWER ADAPTER
HOW TO LEVEL THE EXERCISE BIKE
IMPORTANT: If the exercise bike has been exposed
to cold temperatures, allow it to warm to room
temperature before you plug in the power adapter.
If you do not do this, you may damage the console
displays or other electronic components.
If the exercise bike
rocks slightly on
your floor during
use, turn one or
both of the leveling
feet under the rear
stabilizer until the
rocking motion is
eliminated.
Plug the power
adapter into the
receptacle on the
frame of the exercise bike. Plug the
power adapter into
Power Adapter
an appropriate outlet
that is properly
installed in accordance with all local codes and ordinances.
HOW TO MOVE THE EXERCISE BIKE
To move the exercise bike, hold the
handle on the rear
stabilizer and carefully lift it until the
Handle
exercise bike can be
moved on the front
wheels. Carefully
move the exercise
bike to the desired location and then lower it.
HOW TO ADJUST THE PEDAL STRAPS
To loosen the strap
on a pedal, press
the indicated tab
and pull the strap
upward. To tighten
the strap, simply pull
the end of the strap
downward.
Pedal
Strap
Tab
HOW TO ADJUST THE SEAT
The seat can be
adjusted forward
or backward to the
position that is the
most comfortable
for you. To adjust
the seat, push
downward on the
seat adjustment
handle, slide the
seat to the desired
position, and then
pull upward on the
handle to lock the
seat in place.
Leveling
Feet
Handle
15
CONSOLE DIAGRAM
MAKE YOUR FITNESS GOALS A REALITY WITH
IFIT.COM
Upload your workout results to the iFit cloud
and track your accomplishments.
With your new iFit-compatible fitness equipment, you
can use an array of features on iFit.com to make your
fitness goals a reality:
Set calorie, time, or distance goals for your
workouts.
Exercise anywhere in the world with
customizable Google Maps.
Choose and download sets of weight-loss
workouts
Download training workouts designed to
help you reach your personal goals.
Go to iFit.com to learn more.
Measure your progress by competing
against other users in the iFit community.
16
FEATURES OF THE CONSOLE
you can download personalized workouts, create your
own workouts, track your workout results, race against
other iFit users, and access many other features.
To purchase an iFit module at any time, go to
www.iFit.com or call the telephone number on the
front cover of this manual.
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the resistance of the pedals with the touch
of a button. While you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the handgrip heart rate monitor.
You can even connect your MP3 player or CD player
to the console sound system and listen to your favorite
music or audio books while you exercise.
To use the manual mode, see page 18. To use
an onboard workout, see page 20. To use a
set-a-goal workout, see page 21. To use an iFit
workout, see page 22. To use the sound system,
see page 23. To change console settings, see
page 24.
The console also offers a selection of onboard
workouts. Each workout automatically changes the
resistance of the pedals as it guides you through an
effective workout. You can also set a customized workout goal with the set-a-goal workout.
The console also features an iFit mode that enables
the console to communicate with your wireless network
through an optional iFit module. With the iFit mode,
Note: If there is a sheet of plastic on the console,
remove the plastic.
17
HOW TO USE THE MANUAL MODE
Distance (Dist.)—This display mode will show
the distance that you have pedaled in miles or
kilometers.
1. Begin pedaling or press any button on the
console to turn on the console.
Pulse—This display mode will show your heart rate
when you use the handgrip heart rate monitor (see
step 5 on page 19).
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Select the manual mode.
Resistance (Resist.)—This display mode will
show the resistance level of the pedals for a few
seconds each time the resistance level changes.
Press the Manual button on the console to select
the manual mode.
Speed—This display mode will show your pedaling
speed in miles per hour or kilometers per hour.
If a wireless iFit module is not inserted into the console and connected to iFit.com, the manual mode
will be selected automatically.
Time—When the manual mode is selected, this
display mode will show the elapsed time. When an
onboard workout is selected, this display mode will
show the time remaining in the workout.
3. Change the resistance of the pedals as desired.
As you pedal, change the resistance of the pedals
by pressing the Quick Resistance increase and
decrease buttons or by pressing one of the numbered Quick Resistance buttons.
The matrix offers several display tabs. Press the
Display button until the desired tab is shown. You
can also press the increase and decrease buttons
next to the Enter button.
Note: After you press a button, it will take a
moment for the pedals to reach the selected resistance level.
Speed—This tab will show a profile of the speed
settings of the workout. A new segment will appear
at the end of each minute.
4. Follow your progress with the display.
My Trail—This tab will show a track that represents
1/4 mile (400 m). As you exercise, the flashing
rectangle will show your progress. The My Trail tab
will also show the number of laps you complete.
The display can show the following workout
information:
Calorie—This tab will show the approximate
amount of calories you have burned. The height of
each segment represents the amount of calories
burned during that segment.
As you exercise, the workout intensity level bar
will indicate the approximate intensity level of your
exercise.
Calories (Cals.)—This display mode will show the
approximate number of calories you have burned.
Calories per Hour (Cals./Hr)—This display mode
will show the approximate number of calories you
are burning per hour.
18
Press the Home button to return to the default
menu (see HOW TO CHANGE CONSOLE
SETTINGS on page 24 to set the default menu).
If necessary, press the Home button again.
When your pulse is detected, a heart symbol in the
calorie display will flash each time your heart beats,
one or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15
seconds.
When a wireless iFit module
is connected, the wireless
symbol at the top of the display will show the strength of
your wireless signal. Four arcs
indicate full signal strength.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
Change the volume level of
the console by pressing the
volume increase and decrease
buttons.
6. Turn on the fan if desired.
5. Measure your heart rate if desired.
The fan has low and high
speed settings. Press the fan
increase and decrease buttons repeatedly to select a fan
speed or to turn off the fan.
If there are
sheets of plastic
Contacts
on the metal
contacts on the
handgrip heart
rate monitor,
remove the
plastic. To measure your heart
rate, hold the
handgrip heart
rate monitor with your palms resting against the
contacts. Avoid moving your hands or gripping
the contacts tightly.
Note: If the pedals do not move for about thirty
seconds, the fan will turn off automatically.
7. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for several seconds, a
tone will sound, the console will pause, and the
time will flash in the display. To resume your workout, simply resume pedaling.
If the pedals do not move for several minutes and
the buttons are not pressed, the console will turn
off and the display will be reset.
19
HOW TO USE AN ONBOARD WORKOUT
speed will appear in the display for a few seconds
to alert you. The resistance of the pedals will then
change.
1. Begin pedaling or press any button on the
console to turn on the console.
As you exercise, you will be prompted to keep your
pedaling speed near the target speed for the current segment. When an upward-pointing arrow
appears in the display, increase your pace. When
a downward-pointing arrow appears, decrease
your pace. When no arrow appears, maintain
your current pace.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Select an onboard workout.
To select an onboard workout, press the Calorie
button or the Performance button repeatedly until
the desired workout appears in the display.
IMPORTANT: The target speed is intended only
to provide motivation. Your actual pedaling
speed may be slower than the target speed.
Make sure to pedal at a speed that is comfortable for you.
When you select an onboard workout, the display
will show the duration of the workout and the name
of the workout. A profile of the speed settings of the
workout will appear in the matrix.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Quick Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
The maximum resistance level and the maximum
speed for the workout will also appear in the
display.
3. Begin pedaling to start the workout.
Each workout is divided into one-minute segments. One resistance level and one target speed
is programmed for each segment. Note: The same
resistance level and/or target speed may be programmed for consecutive segments.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. The time will flash in the display. To
resume the workout, simply resume pedaling.
During the
workout,
the profile
on the
speed
tab will
Profile
show your
progress.
The flashing segment of the profile represents the
current segment of the workout. The height of the
flashing segment indicates the target speed for the
current segment.
4. Follow your progress with the display.
See step 4 on page 18.
5. Measure your heart rate if desired.
See step 5 on page 19.
6. Turn on the fan if desired.
See step 6 on page 19.
7. When you are finished exercising, the console
will turn off automatically.
At the end of each segment of the workout, a
series of tones will sound and the next segment of
the profile will begin to flash. If a different resistance level and/or target speed is programmed for
the next segment, the resistance level and/or target
See step 7 on page 19.
20
HOW TO USE A SET-A-GOAL WORKOUT
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance during the workout, the
number of calories you burn will be affected.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Set a calorie, distance, or time goal.
The workout will continue in this way until the goal
is reached. To pause the workout, stop pedaling.
The time will pause in the display. To resume the
workout, simply resume pedaling.
To set a calorie, distance, or time goal, first press
the Set A Goal button.
Next, press the increase and decrease buttons
next to the Enter button until the name of the
desired goal appears in the display. Then, press
the Enter button.
4. Follow your progress with the display.
See step 4 on page 18.
5. Measure your heart rate if desired.
Then, press the increase and decrease buttons
next to the Enter button to set the desired goal.
See step 5 on page 19.
3. Begin pedaling to start the workout.
6. Turn on the fan if desired.
Each workout is divided into one-minute segments.
You can manually change the resistance of the
pedals as desired during the workout by pressing
the Quick Resistance buttons.
See step 6 on page 19.
7. When you are finished exercising, the console
will turn off automatically.
Note: If you manually change the resistance during
a calorie goal workout, the length of the workout
will adjust automatically to ensure that you meet
your calorie goal.
See step 7 on page 19.
21
HOW TO USE AN IFIT WORKOUT
Press the Map button, the Train button, or the Lose
Wt. button to download the next workout of that
type in your schedule.
You must have an iFit module to use an iFit workout.
To purchase an iFit module at any time, go to
www.iFit.com or call the telephone number on the
front cover of this manual.
Press the Compete button to compete in a race
that you have previously scheduled.
Note: To use an iFit module, you must have access
to a computer with an internet connection and a USB
port. You will also need an iFit.com membership. To
use a wireless iFit module, you must also have your
own wireless network including an 802.11b/g/n router
with SSID broadcast enabled (hidden networks are not
supported).
Press the Track button to re-run a recent iFit workout from your schedule. Next, press the increase
and decrease buttons to select the desired workout. Then, press the Enter button to start the
workout.
For more information about the iFit workouts,
please see www.iFit.com.
1. Begin pedaling or press any button on the
console to turn on the console.
When you select an iFit workout, the display will
show the duration of the workout and the approximate number of calories you will burn. The display
may also show the name of the workout. If you
select a competition workout, the display may
count down to the beginning of the race.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Make sure that the iFit module is inserted in the
console.
Note: The iFit buttons may also run demo workouts. To use the demo workouts, remove the iFit
module from the console and press one of the iFit
buttons.
To use an iFit workout, make sure that the iFit module is inserted in the console.
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter in
the iFit module must be at least 8 in. (20 cm)
from all persons and must not be near or connected to any other antenna or transmitter.
5. Start the workout.
See step 3 on page 20.
During some workouts, an audio coach will guide
you through your workout. You can select a setting for the audio coach (see HOW TO CHANGE
CONSOLE SETTINGS on page 24).
3. Select a user.
If more than one user is registered with your
iFit.com membership, you can switch users in the
iFit main screen. Press the increase and decrease
buttons next to the Enter button to select a user.
To stop the workout at any time, stop pedaling. The
time will flash in the display. To resume the workout, simply resume pedaling.
4. Select an iFit workout.
To select an iFit workout, press one of the iFit buttons. Before some workouts will download, you
must add them to your schedule on www.iFit.com.
22
6. Follow your progress with the display.
HOW TO USE THE SOUND SYSTEM
See step 4 on page 18.
To play music or audio books through the console
sound system while you exercise, plug a 3.5 mm male
to 3.5 mm male audio cable (not included) into the jack
on the console and into a jack on your MP3 player,
CD player, or other personal audio player; make sure
that the audio cable is fully plugged in. Note: To
purchase an audio cable, see your local electronics
store.
The My Trail tab will show a map of the trail or it will
show a track and the number of laps you complete.
During a competition workout, the Competition tab
will show your progress in the race. As you race,
the top line in the matrix will show how much of the
race you have completed. The other lines will show
other competitors. The end of the matrix represents
the end of the race.
Next, press the play button on
your personal audio player. Adjust
the volume level using the volume
increase and decrease buttons
on the console or the volume control on your personal
audio player.
7. Measure your heart rate if desired.
See step 5 on page 19.
8. Turn on the fan if desired.
See step 6 on page 19.
9. When you are finished exercising, the console
will turn off automatically.
See step 7 on page 19.
For more information about iFit features, go to
www.iFit.com.
23
HOW TO CHANGE CONSOLE SETTINGS
Units—The currently selected unit of measurement
will appear in the display. To change the unit of
measurement, press the Enter button repeatedly.
To view distance in miles, select ENGLISH. To view
distance in kilometers, select METRIC.
1. Select the settings mode.
To select the settings mode, press the Settings
button.
Contrast Level—The currently selected contrast
level will appear in the display. Press the Quick
Resistance increase and decrease buttons to
adjust the contrast level.
The display will show the total number of hours
that the exercise bike has been used and the total
distance (in miles or kilometers) that has been
pedaled on the exercise bike.
If an iFit module is connected to the console, the
display will show the words WIFI MODULE or USB
MODULE.
Trainer Voice—The currently selected setting for
the audio coach will appear in the display. Press
the Enter button repeatedly to turn the audio coach
ON or OFF.
If no module is connected, the display will show
the words NO IFIT MODULE. If no module is connected, some of the settings options will not be
available.
Default Menu—The default menu will appear when
you press the Home button. Press the Enter button
repeatedly to select the manual mode or the iFit
menu as the default menu.
2. Navigate the settings mode.
Check Status—The words CHECK WIFI STATUS
or CHECK USB STATUS will appear in the display.
Press the Enter button. After a few seconds, the
status of the iFit module will appear in the display.
To exit this display, press the Settings button.
While the settings mode is selected, the matrix of
the display will display several optional screens.
Press the decrease button next to the Enter button
repeatedly to select the desired optional screen.
Send/Receive—The words SEND/RECEIVE DATA
will appear in the display. Press the Enter button.
The console will then check for iFit workouts and
firmware downloads.
The lower section of the display will show instructions for the selected optional screen. Make sure
to follow the instructions shown in the lower
part of the display.
4. Exit the settings mode.
3. Change settings as desired.
Press the Settings button to exit the settings mode.
Demo—The console features a display demo
mode, designed to be used if the exercise bike
is displayed in a store. While the demo mode is
turned on, the screen will show a demo presentation. Press the Enter button repeatedly to turn the
demo mode ON or OFF.
24
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the exercise bike
regularly. Replace any worn parts immediately.
Next, locate the Reed Switch (46). Rotate the Pulley
(29) until a Pulley Magnet (30) is aligned with the Reed
Switch. Loosen, but do not remove, the indicated M4
x 16mm Screw (77). Slide the Reed Switch slightly
toward or away from the Pulley Magnet.
To clean the exercise bike, use a damp cloth and a
small amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
CONSOLE TROUBLESHOOTING
29
If the console does not turn on, make sure that the
power adapter is fully plugged in. If lines appear in the
console display, see HOW TO CHANGE CONSOLE
SETTINGS on page 24 and adjust the contrast level
of the display.
77
46
30
If the handgrip heart rate monitor does not function
properly, see step 5 on page 19.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed
switch, first unplug
the power adapter.
Using a flat screwdriver, release the
tabs at the front and
along the sides of
the Top Shield (44).
Then, slide the Top
Shield upward.
Then, retighten the M4 x 16mm Screw (77). Plug in the
power adapter and turn the Pulley (29) for a moment.
Repeat these actions until the console displays correct
feedback.
When the reed switch is correctly adjusted, reattach
the top shield and then plug in the power adapter.
44
25
HOW TO ADJUST THE DRIVE BELT
Next, loosen the M6 x 20mm Hex Screw (84). Then,
tighten the M10 x 50mm Hex Screw (83) until the Drive
Belt (47) is tight. When the Drive Belt is tight, tighten
the M6 x 20mm Hex Screw.
If the pedals slip while you are pedaling, even while the
resistance is adjusted to the highest setting, the drive
belt may need to be adjusted.
To adjust the drive belt, first unplug the power adapter.
Then, you must remove the top shield, the right pedal,
and the right shield (see the instructions below).
Using a flat screwdriver, release the
tabs at the front
and along the
sides of the Top
Shield (44). Then,
slide the Top
Shield upward.
47
44
84
83
Next, using an adjustable wrench, turn the right pedal
counterclockwise and remove it. Then, remove the
screws from the right and left shields, and gently
remove the right shield.
When the Drive Belt (47) is correctly adjusted, reattach
the right shield, the right pedal, and the top shield and
then plug in the power adapter.
26
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
27
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
28
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
4
1
1
1
1
2
1
1
2
1
2
4
1
2
1
1
1
1
1
1
1
1
1
2
Model No. PFEX13813.0 R1013A
Description
Key No. Qty.
Frame
Upright
Front Stabilizer Cover
Console
Rail
Adjustment Bar
Left Handlebar
Backrest
Seat
Seat Handlebar/Wire
Seat Handlebar Cap
Brake Block
Left Front Shield
Right Front Shield
Front Stabilizer
Rear Stabilizer
Wheel
Brake
Leveling Foot
Right Handlebar
Right Pedal/Strap
Left Pedal/Strap
Right Crank Arm
Left Crank Arm
M6 x 18mm Screw
Adjustment Bar Handle
Handle Bracket
Large Snap Ring
Pulley
Pulley Magnet
Crank
Brake Axle
Crank Bearing
Eddy Mechanism
Mechanism Spacer
M10 Split Washer
Resistance Motor
Tree Fastener
Idler
Accessory Tray
Seat Carriage
Frame Pulse Wire/Receptacle
Main Wire
Top Shield
Clamp
Reed Switch/Wire
Drive Belt
Rear Stabilizer Cover
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
*
*
2
2
1
2
1
1
8
3
1
1
8
2
1
4
2
5
4
2
4
1
4
8
2
5
2
8
4
1
33
4
1
4
2
6
1
1
2
1
12
8
10
1
7
1
12
–
–
Description
Handlebar Grip
Flange Screw
Power Adapter
M10 Locknut
Left Rear Shield
Right Rear Shield
Carriage Bearing
M4 x 25mm Screw
Rear Upright Cover
Front Upright Cover
Carriage Bushing
Rail Rod
M6 x 15mm Shoulder Screw
Rod Cap
Brake Spacer
M6 x 16mm Screw
M10 x 105mm Screw
Wheel Bolt
M8 x 38mm Screw
M6 Large Washer
M8 x 16mm Screw
M6 x 30mm Screw
M6 x 65mm Bright Bolt
M6 Split Washer
1/4" x 14mm Screw
M8 x 28mm Bolt
M10 x 16mm Screw
Steel Washer
M4 x 16mm Screw
M8 x 12mm Screw
M4 x 16mm Bright Screw
Rail Screw
M6 Locknut
M4 x 12mm Flange Screw
M10 x 50mm Hex Screw
M6 x 20mm Hex Screw
Crank Cap
Backrest Back
M8 Split Washer
M6 Washer
M8 Jam Nut
Pulse Bracket
Small M6 Washer
Motor Bracket
M4 x 16mm Flange Screw
Assembly Tool
User’s Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
29
77
77
77
70
38
88
93
70
93
54
88 70
86
38
93
93
30
77
53
77
77
8
10
25
88
7
67
9
25
77
4
11
69
77
88
49
77
75
57
36
2
36
36
75
77
58
77
69
20
69
77
49
77
EXPLODED DRAWING A
Model No. PFEX13813.0 R1013A
31
51
81
5
62
89
55
89
80
32
71
55
74
62
60
80
65
19
48
87
18
89
63
72
12
59
80 81
62
89
87
41
59
91
55
64
63
91
64
72
80
74
71
87
73
60
55
26
62
19
16
90
87
77
77
59
77
74
64
89
6
91
55 59
91
27
22
85
24
42
89
74
50
35
77
77
48
1
34
43
35
89
28
77
13
45
83
39
33
46
79
76
3
92
61 82 37
30
31
68 84
33
47
14
82
77
29
30
87 78
15
66
78
77
87
40
77
56
56
77
52
17
44
56
50
3
21
85
23
77
66
17
65
EXPLODED DRAWING B
Model No. PFEX13813.0 R1013A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: To protect your fitness equipment with an extended service plan, see page 5.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. Parts and labor
are warranted for one (1) year from the date of purchase.
This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is
limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
or if the product is used for commercial or rental purposes. No other warranty beyond that specifically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specific legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 351557 R1013A
Printed in China © 2013 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement