Scosche Stereo Dash Kits Installation Instructions

Scosche Stereo Dash Kits Installation Instructions
S3-1
PRELIMINARY
S3-1 Functionality by vehicle platForm:
Make
MULTI-PLATFORM STEREO REPLACEMENT
WITH STEERING WHEEL CONTROL INTERFACE
FOR CHRYSLER, GM, FORD & TOYOTA JBL
STEERING WHEEL CONTROLS
CLARION PIONEER S3-1 INSTALLATION HARNESSES*
S3CR02 2005-10 Select Chrysler S3-1 harness
S3CR04 2007-UP Select Chrysler S3-1 harness
S3FD23
2005-UP Select Ford, Linc, Merc S3-1 harness
S3GMCL2 2003-UP Select GM Class II S3-1 harness
S3GM11C
2004-UP Select GM LAN11 24Pin S3-1 harness
S3GM11L 2006-UP Select GM LAN11 14/16Pin S3-1 harness
S3GMLAN 2006-UP Select GM LAN29 14/16 Pin S3-1 harness
S3TA03
2004-UP Select Toyota JBL S3-1 harness
Premium
Sound
Activation
Fade F/R
Not required
No
Not required
No
GM LAN
Std. Bose only
GM Class II
Std. Bose only
!
Not required
Not required
JBL Sys only
No
beFore beGinninG: READ THIS INSTRUCTION MANUAL
Disconnect the negative battery terminal to avoid short circuits. Read ALL
vehicle manufacturer’s warnings regarding airbags and electrical systems.
We recommend ONLY a volt/ohm meter when checking/testing vehicle
wiring. A test light (grounded probe type) can damage a vehicle’s computer
and/or electronics systems.
COMPONENT OVERVIEW
STEERING WHEEL
CONTROL MODULE
JVC
SONY
A vehicle-specific harness is required for installing the S3-1 interface (*sold separately).
Verify your vehicle’s compatability by checking the list included with vehicle-specific
harness.
Warning
Chimes
Ford
NO Steering wheel programming is required! The S3-1 Interface has
built-in protocols for popular aftermarket stereos including:
ALPINE KENWOOD Steering
Wheel
Controls
Chrysler
Toyota
The cutting edge S3-1 interface from Scosche allows you to replace your
factory OEM stereo while retaining all necessary safety & warning features as
well as retaining your original steering wheels controls (if vehicle is equipped).
ACC/R.A.P.
Power
3.5MM STEERING
WHEEL OUTPUT
(Alpine, Clarion,
JVC, Pioneer, Sony)
BLUE STEERING
WHEEL OUTPUT
(Kenwood)
S3-1 INTERFACE
MODULE
INSTALLATION OVERVIEW
AFTERMARKET
STEREO
WIRE COLOR CODES
White
White/Black
Green
Green/Black
Black
Yellow
Red
Blue
3.5MM STEERING WHEEL
OUTPUT CABLE
(Alpine, Clarion, JVC,
Pioneer, Sony)
= Left Front Positive (LF+)
= Left Front Negative (LF-)
= Left Rear Positive (LR+)
= Left Rear Negative (LR-)
= Chassis Ground
= +12V Constant Power
= +12V Accessory/R.A.P output
= +12V Power Antenna
Gray
Gray/Black
Violet
Violet/Black
Orange
Blue/White
= Right Front Positive (RF+)
= Right Front Negative (RF-)
= Right Rear Positive (RR+)
= Right Rear Negative (RR-)
= Illumination
= +12 Remote Output
(Amp, radio on signal)
NAvIGATION CONNECTIONS:
BLUE STEERING WHEEL
OUTPUT WIRE (Kenwood)
S3-1 vEHICLE-SPECIFIC
WIRE HARNESS
(sold separately for
Chrysler, Ford,
GM, Toyota)
Violet/White
Red/White
Yellow/Black
Orange/White
= VSS Vehicle speed pulse signal
= Reverse light trigger (+12V when in reverse gear)
= Parking brake trigger (-12V when park brake ON)
= Auto illumination (Data controlled lighting output on some GM LAN
applications with AUTO headlights enabeled)
NOTE: The RED Accessory output wire from the S3-1 interface is rated at 10A Max
output for most aftermarket head unit demands. We do NOT recommended
connecting additional +12V switched accessories to this output source as
it may cause damage to the S3-1 module itself. If 10A output is not
sufficient, then a relay is needed (Relay not included).
NOTE: Illumination & auto illumination outputs are designed for head unit
connections only.
S3-1 SPEAKER / AUDIO CONNECTIONS
RCA LOW LEvEL
•
•
•
GM Bose
(Excludes Prem. Bose)
Ford Premium Sound
Toyota JBL/Lexus
S3-1 MAIN
MODULE
STEERING
WHEEL
MODULE
TO vEHICLE
SPEAKER WIRE
(Cut-off RCAs)
• Chrysler
• Ford (Non-Premium)**
• GM Bose (Non-Bose)
**ATTN: All Ford Harness RCA cutting must be performed on vehicle side of the
circuit board.
BASIC WIRING INSTRUCTIONS
The following steps are provided as a general guide. For specific information for your
vehicle, consult the instructions supplied with your vehicle-specific S3-1 harnness
(sold separately).
1. Disconnect the negative battery cable from the battery to avoid short circuits.
2. Remove and unplug factory stereo.
3. Match and connect the Power/ground wires from the S3-1 Vehicle specific
harness to the wires provided with your stereo. The color codes on the Scosche
harness are designed to match most aftermarket stereos.
• Take note that some of the wires for your new stereo come from the S3-1
interface box itself and not the vehicle connectors.
4a. The S3-1 speaker connections are pre-terminated with RCA jacks for installations
requiring Line input: Toyota JBL, GM Standard Bose and Ford Premium sound.
4b. If your vehicle does not have a Bose or Premium system, cut off the RCAs
and wire the speaker leads directly to the speaker wires from the new stereo.
4c. All FORD harnesses must have RCAs cut on vehicle side of circuit board.
5. Tape any unused wiring to prevent short circuit.
7. Reconnect the negative battery cable**.
** For GM vehicles, alternate power up (initialization steps) are required.
See General Motors specific notes section.
8. As you install your new stereo, place the S3-1 module(s) and harnesses in the rear
of the dash cavity behind the stereo.
OPTIONAL: Cable ties or double-sided tape can be used to secure the module, but
are not included.
CHRYSLER & TOYOTA INSTALLATION NOTES
CHRYSLER: PREMIUM ALPINE, BOSTON & INFINITY SYSTEMS
These factory amplified sound systems are driven and digitally controlled by a single
set of left/right input channels only. The aftermarket radio does not have the ability to
control fade or balance adjustments on these types of systems. There is NO front/rear
fader control. The balance and fader are set to center by interface control software.
TOYOTA JBL / LEXUS PREMIUM SYSTEMS
These factory amplified sound systems are driven and digitally controlled by a single
set of left/right input channels only. The aftermarket radio does not have the ability to
control fader on these types of systems. There is NO front/rear fader control. The fader
is set to center by interface control software.
GENERAL MOTORS INSTALLATION NOTES
HOW TO TEST FOR “PREMIUM BOSE” SYSTEMS
There are two types of Bose systems available in some models of GM vehicles. The
S3-1 interface is not compatible with the Digital Premium BOSE (y91/z75 systems) To
test for digital Bose systems, turn the factory radio volume up and down rapidly. If the
sound system reacts immediately then the system is a Standard Bose, not a Premium
Bose. If there’s a slight delay in the system as you turn it up and down quickly, then this
vehicle may have Premium BOSE. Note: you may also check the service parts code
sticker usually located in the glove box for “y91” or “z75” equipment codes.
S3-1 GENERAL MOTORS INTEGRATED SAFETY & WARNING CHIMES
When replacing the factory stereo in your GM vehicle, the S3-1 interface will replace
portions of your vehicle’s audible SAFETY and WARNING CHIME systems. If the stereo
is removed without the proper accessory these functions of your vehicle will be LOST
including: Your vehicle’s ECM (Electronics Control Module) will also store an error code if
operated without the factory radio installed and you may experience difficulty in having
the vehicle serviced at the dealership. The Scosche S3-1 will send the proper data
commands to your vehicle’s ECM (Electronics Control Module) to indicate a “healthy”
status for diagnostic purposes.
WARNING & SAFETY CHIMES LIST:
•
•
•
•
Parking assist
Lights left on reminder
Turn signal click
Low fuel
• Seatbelt warning chime
• Check engine/service indicator
• Key left in ignition reminder
POWER UP (Initialization procedure)
In order to ensure the proper functionality of the S3-1’s +12V RED Accessory wire, we
recommend that the following procedure be followed; in sequence.
1. Disconnect the Scosche Interface from the vehicle radio harness.
2. Close all doors and hood, Turn off all lights and remove the keys from the ignition.
3. Wait 3 to 4 minutes (without opening a door, turning on a light, inserting keys,etc.).
4. Connect the Scosche Interface to the vehicle’s radio harness and start vehicle.
5. Test interface for functionality.
STEERING WHEEL MODULE
STEERING WHEEL CONTROLS: CHRYSLER
STEERING WHEEL MODULE SETUP
CHRYSLER / DODGE / JEEP Version 1
STEERING WHEEL LEGEND 2005-08
The Scosche S3-1 offers “plug and play” steering wheel control setup. No complicated
learning, programming or splicing wires is required. Setup can be completed in just
seconds! (Tool is provided by Scosche.)
1. Break off the small flat blade
adjustment driver from the
side of the steering wheel
module housing as shown in
illustration.
2. Carefully click the selector (arrow)
dial to the correct letter that
corresponds with the brand of
aftermarket stereo you are installing:
A=ALPINE, C=CLARION, J=JVC,
K=KENWOOD, P=PIONEER, S=SONY
SEEK UP
PRESET
SEEK DOWN
SOURCE
vOLUME
vOLUME
S
J
K
C
A
P
Sony
JVC
Kenwood
Clarion
Alpine
Pioneer
Vol Up +
Vol +
Vol +
Vol +
Vol +
Vol +
Vol +
Vol Down -
Vol -
Vol -
Vol -
Vol -
Vol -
Vol -
Source
Source
Source
Source
Source
Source
Source
Preset
FM Presets
FM Presets
Seek Up/Trk Up
FM Preset/Disc Trk 1
FM Presets
FM Presets
Seek Up
Seek Up/Track Up
Sk Up/Trk Up
Seek Up/Trk Up
FM Preset Up/Trk Up
Seek Up/Track Up
Seek Up/Track Up
Seek Down
Seek Dn/Track Dn
Sk Dn/Trk Dn
Seek Dn/Trk Dn
FM Preset Dn/Trk Dn
Seek Dn/Track Dn
Seek Dn/Track Dn
CHRYSLER / DODGE / JEEP Version 2
STEERING WHEEL LEGEND 2009-UP
(Uses controls on BACK of Steering wheel ONLY)
vOL UP
SEEK UP
SOURCE
PRESET
vOL
DOWN
3. Connect the steering wheel control module harness to the Main S3-1
interface via the 10-Pin connector. (This step not shown)
4. Plug the 3.5mm connector into the “Remote” jack on the back of your
aftermarket stereo. For Kenwood, connect the Blue wire to the remote
control input wire of the radio. (This step not shown)
SEEK
DOWN
S
J
K
C
A
P
Sony
JVC
Kenwood
Clarion
Alpine
Pioneer
Vol Up +
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Down -
Vol Dwn
Vol Dwn
Vol Dwn
Vol Dwn
Vol Dwn
Vol Dwn
Source
Source
Source
Source
Source
Source
Source
Seek Up
Seek Up/Track Up
Sk Up/Trk Up
Seek Up/Trk Up
FM Preset Up/Trk Up
FM Presets
Seek Up/Track Up
Seek Down
Seek Dn/Track Dn
Sk Dn/Trk Dn
Seek Dn/Trk Dn
FM Preset Dn/Trk Dn
Seek Up/Track Up
Seek Dn/Track Dn
Preset
Next FM Preset
Preset Up
Seek Up/Trk Up
FM Preset /Disk Trk 1
Next FM Preset
Next FM Preset
Volume control note:
Press once: up/down (one increment); Press and hold: up/down (continuous)
STEERING WHEEL CONTROLS: GM
STEERING WHEEL CONTROLS: GM
SEEK UP/
PRESET UP
GENERAL MOTORS GM LAN 11 BIT
STEERING WHEEL LEGEND
GENERAL MOTORS
LAN STEERING
WHEEL LEGEND
2006-UP
SOURCE
vOL UP
MUTE
MUTE
vOL UP
vOL DOWN
vOL DOWN
SEEK UP/TRACK UP
SEEK DN/
PRESET DN
PRESET/BAND
S
J
Sony
K
JVC
Kenwood
SEEK DOWN/TRACK DOWN
C
A
Clarion
P
Alpine
Pioneer
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Source
Source
S
J
K
C
A
P
Sony
JVC
Kenwood
Clarion
Alpine
Pioneer
Source
Source
Source
Source
Source
Vol Up+
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Speak Icon Mute
Mute
Mute
Mute
Mute
Mute
Vol Down-
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Seek/Track Up
Preset/Band Preset Up
Band
Seek Up
Band
Preset Up
Preset Up
Seek Up
Seek/Track Up
Seek/Trk Up
Seek/Trk Up
Seek/Track Up
Seek/Track Up
Seek Up
Seek/Track Up
Seek Up
Track Up
Preset/Track Up
Preset Up
Seek/Track Up
Seek Down
Seek/Track Down Seek/Trk Dn
Seek/Trk Dn
Seek/Track Down
Seek/Track Down Seek /Track Down
Seek Down
Seek/Track Dn
Seek Down
Track Down
Preset/Track Down
Seek/Track Down Seek /Track Down
Mute
Mute
Mute
Speak Icon Mute
Mute
GENERAL MOTORS CLASS II
STEERING WHEEL LEGEND
SOURCE
Mute
TOYOTA STEERING WHEEL LEGEND
SEEK UP/TRACK UP
MUTE
vOLUME UP
vOLUME DOWN
vOL UP
SEEK DOWN/
PRESET DOWN
PRESET/BAND
SEEK UP/
PRESET UP
vOL DOWN
SOURCE
SEEK DN/TRACK DN
S
J
K
C
A
P
Sony
JVC
Kenwood
Clarion
Alpine
Pioneer
SOURCE
MODE
Vol Up +
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
Vol Up
S
J
K
C
A
P
Vol Down -
Vol Dwn
Vol Down
Vol Down
Vol Down
Vol Dwn
Vol Dwn
Sony
JVC
Kenwood
Clarion
Alpine
Pioneer
Source Up
Source
Source
Source
Source
Source
Source
Vol Up +
Vol +
Vol +
Vol +
Vol +
Vol +
Vol +
Source Down
Source
Source
Source
Source
Source
Source
Vol Down -
Vol -
Vol -
Vol -
Vol -
Vol -
Vol -
Seek Up
Seek/Track Up
Seek Up
Track Up
Preset/Track Up
Seek/Track Up
Seek/Track Up
Mode
Source
Source
Source
Source
Source
Source
Seek Down
Seek /Track Down Seek Down
Track Down
Preset/Track Dn
Seek/Track Dn
Seek/Track Dn
Seek Up
FM Presets
FM Presets
Seek Up/Trk Up
FM Preset/Disk Trk 1 FM Presets
FM Presets
Speak Icon
Mute
Mute
Mute
Mute
Mute
Mute
Seek Up
Seek Up/Track Up Seek Up/Trk Up Seek Up/Trk Up
FM Preset Up/Trk Up Seek Up/Track Up
Seek Up/Track Up
Program
Preset Up
Band
Seek Up
Band
Preset Up
Preset Up
Seek Down
Seek Dn/Track Dn Seek Dn/Trk Dn Seek Dn/Trk Dn
FM Preset Dn/Trk Dn Seek Dn/Track Dn
Seek Dn/Track Dn
Volume control note:
Press once: up/down (one increment); Press and hold: up/down (continuous)
Volume control note:
Press once: up/down (one increment); Press and hold: up/down (continuous)
STEERING WHEEL NOTES & TROUBLESHOOTING
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROL NOTES & EXCEPTIONS
FORD STEERING WHEEL LEGEND
vOL
vOL DOWN
The illustrations of steering wheel controls and buttons in this manual are “typical”.
The actual controls and placement of the controls varies between each make, model,
trim level, and/or options package. The overall operation and characteristics are
similar between makes.
For Volume UP/DOWN operation, pressing either button once will increase or decrease
ONE small increment. Press and hold for continuous UP or DOWN volume adjustment.
vOL UP
SEEK DOWN
For CD Seek UP/DOWN operation, pressing either button once will skip UP or DOWN
tracks. Press and hold for manual track FWD/RR.
SEEK UP
MEDIA
or
The radio seek UP/DOWN operation varies between stereo brands. In some cases
pressing the seek UP/DOWN button once will skip UP or DOWN to the next strong
radio station. In other cases, this button will select through Memory preset stations
on the stereo. Consult the steering wheel control pages for your particular brand and
configuration.
SOURCE
TROUBLESHOOTING
S
Sony
J
JVC
K
Kenwood
C
Clarion
Vol Up+
Vol Up
Vol Up
Vol Up
Vol Up
Vol Down-
Vol Down
A
P
Alpine
Pioneer
Vol Up
Vol Up
Vol Down
Vol Down
Vol Down
Vol Down
Vol Down
Media/Music Note Source
Source
Source
Source
Source
Source
Seek Up
Seek Up/Track Up
Sk Up/Trk Up
Seek Up/Trk Up
FM Preset Up/Trk Up Seek Up/Track Up Seek Up/Track Up
Seek Down
Seek Dn/Track Dn
Sk Dn/Trk Dn
Seek Dn/Trk Dn
FM Preset Dn/Trk Dn Seek Dn/Track Dn
Mute
Volume control note:
Press once: up/down (one increment); Press and hold: up/down (continuous)
SCOSCHE STEREO INSTALLATION COMPONENTS
Stereo will not respond to Factory steering controls:
Verify vehicle compatibility. Check the S3-1 harness instruction for your particular
vehicle listing.
Verify / Check installation:
1. Check connections at S3-1 module, verify power, ground is present.
2. Check to determine if steering wheel control module is properly connected to
main S3-1 module.
3. Check to determine if steering wheel OUTPUT wire or 3.5mm cable is
connected to the correct steering wheel INPUT at the back of the aftermarket
stereo.
4. Check to determine that steering wheel selection potentiometer is set to
matching brand of aftermarket radio i.e. A: Alpine, C: Clarion, J: JVC,
K: Kenwood, P: Pioneer, S: Sony (see page 3)
STEREO DASH KITS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement