TOA 900 MK2 SERIES POWER AMPLIFIER (240- WATT) P

TOA 900 MK2 SERIES POWER AMPLIFIER (240- WATT) P
TOA 900 MK2 SERIES
POWER AMPLIFIER
(240- WATT )
P-924MK2
Approved
DESCRIPTION
The TOA P-924MK2 Power Amplifier delivers up to
240 watts of power at less than 0.5% total harmonic
distortion (THD) from 20 to 20,000Hz (transformerless
4-ohm output). Optional plug-in modules are available for
use with the P-924MK2 to provide a full range of operating
applications. The use of edge connectors on the rear of the
unit permits selection from a wide assortment of TOA plugin modules.
A low-cut switch for a cutoff frequency of 60Hz and an input
level switch for an input sensitivity of 1V (0dBV) or 0.1V
(-20dBV) are provided. The P-924MK2 has output
terminals to match 4- or 8-ohm speaker systems and 25- or
70-volt constant voltage speaker distribution systems. An
optional rack mounting bracket is available.
FEATURES
1. Output power: 240 watts RMS
2. Wide frequency response: 20 to 20,000Hz ±1dB
3. Low distortion and noise level
4. Excellent output regulation
5. Built-in protection circuitry when heat sink temperature
overheats
6. Separate output terminals for 4 and 8 ohms, 25 and
70 volts constant voltage speaker distribution systems
7. Full range of plug-in modules
8. Input level switch (1,000mV / 100mV)
9. Mountable in three EIA standard rack units with optional
rack mounting bracket
Frequency Response
at 1/10 rated output (Direct output: 4-ohm load,
transformer output: 21-ohm load)
SPECIFICATIONS
Type
Output Power
Power amplifier
Power Bandwidth
(D) 20-20,000Hz, 0.5% THD
(T) 50-20,000Hz, 0.5% THD
Frequency Response
(D) 20-20,000Hz, ±1dB (T) 20-15,000Hz, ±1dB
(T) 20-20,000Hz, +1dB/-3dB_
0.01% at 1 kHz, rated output
Total Harmonic Distortion
Inputs
Input
(D) 240 watts RMS, (T) 220 watts RMS
One input port: Port accepts any input
module except T-01
One direct input
Note: Use of direct input prohibits use of modular
input port
Sensitivity/Impedance
Source Impedance
Outputs
(T)= Transformer
(D)= Direct
Input port: 100mV or 1000mV(switchable)/10k ohms
Direct input: 100mV or 1000mV(switchable)/10k ohms
Power Output vs. Frequency
at 0.5% THD (Direct output: 4-ohm load,
transformer output: 21-ohm load)
200 ohms with M-01/M-11/M-21/M-51/M-61 modules
(balanced Lo-Z microphone preamplifier)
50k ohms with M-03P module
(unbalanced Hi-Z microphone preamplifier).
R-01 module (mag. phono preamplifier)
220k ohms with U-01/U-11/U-21/U-61 modules
(auxiliary preamplifier)
10k ohms with B-01 module
(bridging transformer)
600 ohms with L-01 module (Iine matching transformer),
I-01 module (paging input)
Architect’s and Engineer’s Specifications
Main (T): 8 ohms, 25 and 70 volts, balanced
Main (D): 4 ohms, unbalanced
Output Regulation (1kHz)
(D): Less than 0.5dB, no load to full load
(T): Less than 1.0dB, no load to full load
Signal-to-Noise Ratio
(Band Pass: 20-20,000Hz)
With Tone Controls Centered
Input level switch in 0dBV (1000mV) position: 108dB
Input level switch in -20dBV (100mV) position: 90dB
Controls
1 input gain control, 1 input level switch,
1 power ON/OFF switch, 1 low-cut switch
Indicators
1 power LED, 1 protect LED, 1 signal LED,
1 normal LED, 1 peak LED
Protection
Self-protection, with 2AC fuses (1 inside) and 2DC fuses
Connectors
Inputs: Card-edge connector and screw-terminal strip
Output: Screw-terminal strip
AC power cord/plug: SJT, 3-prong type
AC outlet: 3-pin grounding type
Power Consumption
120V/3A
Temperature Range
12°F to 140°F (-10°C to +60°C)
Dimensions
16.5”(W) x 6.0”(H) x 13.2”(D) (420 x 151.3 x 334.2mm)
Weight
(without input modules)
43lbs. (19.5kg)
Color
Black
Standard Accessory
1 volume control cover (YA-920), 1 input port cover
Other Features
Output disconnected for approx. 5 seconds after
switching power on.
Optional Accessories
Plug-in modules
(see specifications for individual modules),
Rack mounting bracket model MB-35B
Specifications are subject to change without notice.
NOTE: MODULE WITH MUTING FUNCTION CANNOT BE UTILIZED
IN P SERIES AMPLIFIERS.
The power amplifier shall be capable of operation from a 120V, 50/60Hz line.
Either direct input or plug-in module connections shall be available on the
rear panel. The amplifier shall meet the following performance criteria. Input
sensitivity for rated output shall be available at 0.1V or 1.0V for module input
and direct input. Power output shall be 240W at less than 0.5% THD from 20
to 20,000Hz (direct output) or 50 to 20,000Hz (transformer output).
Frequency response shall be ±1dB from 20 to 20,000Hz (direct output) or 20
to 15,000Hz (transformer output). Input impedance shall be 10,000 ohms for
module input and direct input.
Source impedance shall be 200/50k ohms with a microphone preamplifier,
50k ohms with a mag. phono preamplifier, 220k ohms with an auxiliary
preamplifier, 10k ohms with a bridging transformer, 600 ohms with a line
matching transformer and 600 ohms with a paging input. Load impedance
shall be 4, 8, 2.6 (25V line) or 21 (70V line) ohms. Load voltage shall be
31.0, 43.8, 25 or 70 volts.
Equivalent input noise shall be -126dBm with a Lo-Z microphone
preamplifier. Output noise shall be 90dB below rated output when all gain
controls are off.
TOA plug-in accessory modules designed for use with the power amplifier
shall utilize the latest in surface mount component technology and include
the following modules: the M Series microphone preamplifiers available with
remote volume control, voice gate and compressor options; the U Series
auxiliary preamplifiers available with remote volume control and compressor
options; the R-01 magnetic phono preamplifier; the B Series bridging
transformers; the L Series line matching transformers; the S Series signal
generator modules, and the l-01 TOA intercom system interface paging
module.
The power amplifier shall be rack mounted using the TOA MB-35B rack
mounting bracket. The amplifier’s dimensions shall be 16.5”(W) x 6.0”(H) x
13.2”(D) (420 x 151.3 x 334.2mm) and its weight shall be 43lbs. (19.5kg).
The power amplifier shall be TOA model P-924MK2.
TOA Corporation
Printed in Japan (502) 833-62-059-8A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement